Pioneer PD-10 Manuale utente

Marca: Pioneer

Modello: PD-10

Tipo: Manuale utente

Questo manuale è adatto anche per

Operating Instructions | Mode d’emploi | Bedienungsanleitung |

Istruzioni per I’uso | Handleiding | Manual de instrucciones |

Инструкции по эксплуатации

Super Audio CD Player | Lecteur Super Audio CD |

Super Audio CD-Spieler | Lettore CD Super Audio |

Super-Audio CD-speler | Reproductor de Super Audio CD |

PD-30_PWSYXZT8.book 1 ページ２０１２年５月７日　月曜日　午前１１時３３分

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient

magnitude to constitute a risk of electric

shock to persons.

CAUTION:

TO PREVENT THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT

D3-4-2-1-1_A1_En

WARNING

This equipment is not waterproof. To prevent a fire or

shock hazard, do not place any container filled with

liquid near this equipment (such as a vase or flower

pot) or expose it to dripping, splashing, rain or

moisture.

D3-4-2-1-3_A1_En

WARNING

Before plugging in for the first time, read the following

section carefully.

The voltage of the available power supply differs

according to country or region. Be sure that the

power supply voltage of the area where this unit

will be used meets the required voltage (e.g., 230 V

or 120 V) written on the rear panel.

D3-4-2-1-4*_A1_En

WARNING

To prevent a fire hazard, do not place any naked flame

sources (such as a lighted candle) on the equipment.

D3-4-2-1-7a_A1_En

VENTILATION CAUTION

When installing this unit, make sure to leave space

around the unit for ventilation to improve heat radiation

(at least 10 cm at top, 10 cm at rear, and 10 cm at each

side).

WARNING

Slots and openings in the cabinet are provided for

ventilation to ensure reliable operation of the product,

and to protect it from overheating. To prevent fire

hazard, the openings should never be blocked or

covered with items (such as newspapers, table-cloths,

curtains) or by operating the equipment on thick carpet

or a bed.

D3-4-2-1-7b*_A1_En

Information for users on collection and disposal of old equipment and used batteries

These symbols on the products, packaging, and/or accompanying documents mean

that used electrical and electronic products and batteries should not be mixed with

general household waste.

For proper treatment, recovery and recycling of old products and used batteries,

please take them to applicable collection points in accordance with your national

legislation.

By disposing of these products and batteries correctly, you will help to save valuable

resources and prevent any potential negative effects on human health and the

environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products and batteries,

please contact your local municipality, your waste disposal service or the point of sale

where you purchased the items.

These symbols are only valid in the European Union.

For countries outside the European Union:

If you wish to discard these items, please contact your local authorities or dealer and

ask for the correct method of disposal.

K058a_A1_En

Symbol examples

for batteries

Symbol for

equipment

European model only

Thank you for buying this Pioneer product.

Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put

them away in a safe place for future reference..

PD-30_PWSYXZT8.book 2 ページ２０１２年５月７日　月曜日　午前１１時３３分

If the AC plug of this unit does not match the AC

outlet you want to use, the plug must be removed

and appropriate one fitted. Replacement and

mounting of an AC plug on the power supply cord of

this unit should be performed only by qualified

service personnel. If connected to an AC outlet, the

cut-off plug can cause severe electrical shock. Make

sure it is properly disposed of after removal.

The equipment should be disconnected by removing

the mains plug from the wall socket when left unused

for a long period of time (for example, when on

vacation).

D3-4-2-2-1a_A1_En

CAUTION

The /I STANDBY/ON switch on this unit will not

completely shut off all power from the AC outlet.

Since the power cord serves as the main disconnect

device for the unit, you will need to unplug it from the

AC outlet to shut down all power. Therefore, make

sure the unit has been installed so that the power

cord can be easily unplugged from the AC outlet in

case of an accident. To avoid fire hazard, the power

cord should also be unplugged from the AC outlet

when left unused for a long period of time (for

example, when on vacation).

D3-4-2-2-2a*_A1_En

Operating Environment

Operating environment temperature and humidity:

+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH

(cooling vents not blocked)

Do not install this unit in a poorly ventilated area, or in

locations exposed to high humidity or direct sunlight (or

strong artificial light)

D3-4-2-1-7c*_A1_En

This product is for general household purposes. Any

failure due to use for other than household purposes

(such as long-term use for business purposes in a

restaurant or use in a car or ship) and which requires

repair will be charged for even during the warranty

period.

K041_A1_En

POWER-CORD CAUTION

Handle the power cord by the plug. Do not pull out the

plug by tugging the cord and never touch the power

cord when your hands are wet as this could cause a

short circuit or electric shock. Do not place the unit, a

piece of furniture, etc., on the power cord, or pinch the

cord. Never make a knot in the cord or tie it with other

cords. The power cords should be routed such that they

are not likely to be stepped on. A damaged power cord

can cause a fire or give you an electrical shock. Check

the power cord once in a while. When you find it

damaged, ask your nearest PIONEER authorized

service center or your dealer for a replacement.

S002*_A1_En

CAUTION

This product is a class 1 laser product classified

under the Safety of laser products, IEC 60825-1:2007.

CLASS 1 LASER PRODUCT

D58-5-2-2a_A1_En

Contents

01 Before you start

Disc/content format playback compatibility. . . . . .4

What’s in the box. . . . . . . . . . . . . . . . . . . . . . . . . . 4

Loading the batteries in the remote control . . . . . .4

Using the remote control. . . . . . . . . . . . . . . . . . . . .4

02 Connecting up

Analog audio output connections . . . . . . . . . . . . . 5

Digital audio output connections. . . . . . . . . . . . . . 5

Using centralized control with other Pioneer

components (PD-30 only) . . . . . . . . . . . . . . . . . . . 5

Plugging in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

03 Controls and displays

Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Rear panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Front panel display . . . . . . . . . . . . . . . . . . . . . . . . 7

04 Playback

Playing discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Set the power to Standby. . . . . . . . . . . . . . . . . . . . .8

Fast forward/Fast reverse . . . . . . . . . . . . . . . . . . . .8

Skip function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Direct search

(designate a specific track for playback). . . . . . . . .8

Repeat playback . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Random playback . . . . . . . . . . . . . . . . . . . . . . . . . .8

Programmed playback (Play tracks in a

predetermined order) . . . . . . . . . . . . . . . . . . . . . . .8

View disc data . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

iPod/iPhone/iPad playback

(PD-30 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Confirm what iPod/iPhone/iPad models are

supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Playing your iPod/iPhone/iPad . . . . . . . . . . . . . . . .9

Playing files stored on USB storage devices . . . . 10

05 Using advanced functions

Playing with high-fidelity sound . . . . . . . . . . . . . . 11

Sound Retriever. . . . . . . . . . . . . . . . . . . . . . . . . . .11

Pure Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Changing the playback area (layer)

of an SACD/CD . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Adjusting overall display illumination . . . . . . . . . 11

Auto power down (automatically sets power to

standby). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Playback functions . . . . . . . . . . . . . . . . . . . . . . . 11

06 Additional information

Playable disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Playable file formats . . . . . . . . . . . . . . . . . . . . . . 12

Cautions on use. . . . . . . . . . . . . . . . . . . . . . . . . . 13

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . 14

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

PD-30_PWSYXZT8.book 3 ページ２０１２年５月７日　月曜日　午前１１時３３分

Before you start01

Chapter 1:

Before you start

Disc/content format playback

compatibility

Discs playable on this player are as shown below.

• SACD (Super Audio CD)*

(2-channel area only)

•CD

•DSD disc

* “Super Audio CD” is a registered trademark.

Note

• This unit does not permit playback of the multi-

channel areas of SACD discs.

• This unit’s DIGITAL OUT terminals do not output

sound from SACD and DSD discs, nor from iPod/

iPhone/iPad devices.

• When a disc is loaded, turning on the power will not

cause playback to automatically start. As a result,

timed playback is not possible even if the unit is

connected to a timer.

About DualDisc playback

A DualDisc is a new two-sided disc, one side of which

contains DVD content video, audio, etc. while the other

side contains non-DVD content such as digital audio

material. The non-DVD, audio side of the disc is not

compliant with the CD Audio specification and therefore

may not play. For more detailed information on the

DualDisc specification, please refer to the disc

manufacturer or disc retailer.

Discs that cannot be played

•DVD-Video

• DVD-Audio

•CD-G

•Video CD

• DTS CD

It is possible that some discs other than the ones listed

above may not be playable either.

What’s in the box

Please confirm that the following accessories are in the

box when you open it.

• Remote control x1

• AAA/IEC R03 dry cell batteries x2

• RCA audio cable (red/white plugs) x1

•Power cord

•Warranty card

• Operating instructions (This document)

Note

• Illustrations featured in the Operating Instructions

may have been modified or simplified for ease of

explanation, and may therefore differ from the

actual product appearance.

• The illustrations used here are mainly of the PD-30.

Loading the batteries in the remote

control

1 Open the rear lid.

PD-30

PD-10

2 Insert the new batteries, matching the

polarities as indicated inside the case.

3 Close the rear lid.

The batteries included with the unit have been provided

to allow you check product operation and may not last

long. We recommend using alkaline batteries that have

a longer life.

WARNING

• Do not use or store batteries in direct sunlight or

other excessively hot place, such as inside a car or

near a heater. This can cause batteries to leak,

overheat, explode or catch fire. It can also reduce

the life or performance of batteries.

Caution

Incorrect use of batteries may result in such hazards as

leakage and bursting. Observe the following

precautions:

• When inserting the batteries, make sure not to

damage the springs on the battery’s  terminals.

• Do not use any batteries other than the ones

specified. Also, do not use a new battery together

with an old one.

• When loading the batteries into the remote control,

set them in the proper direction, as indicated by the

polarity marks ( and ).

• Do not heat batteries, disassemble them, or throw

them into flames or water.

• Batteries may have different voltages, even if they

are the same size and shape. Do not use different

types of batteries together.

• To prevent leakage of battery fluid, remove the

batteries if you do not plan to use the remote

control for a long period of time (1 month or more).

If the fluid should leak, wipe it carefully off the

inside of the case, then insert new batteries. If a

battery should leak and the fluid should get on your

skin, flush it off with large quantities of water.

• When disposing of used batteries, please comply

with governmental regulations or environmental

public institution’s rules that apply in your country/

area.

Using the remote control

The remote has a range of about 7 m at an angle of about

30º from the remote sensor.

Keep in mind the following when using the remote

control:

• Make sure that there are no obstacles between the

remote and the remote sensor on the unit.

• Remote operation may become unreliable if strong

sunlight or fluorescent light is shining on the unit’s

remote sensor.

• Remote controllers for different devices can

interfere with each other. Avoid using remotes for

other equipment located close to this unit.

• Replace the batteries when you notice a fall off in

the operating range of the remote.

PD-30

PD-10

PD-30

PD-10

7 m

30 °

PD-30_PWSYXZT8.book 4 ページ２０１２年５月７日　月曜日　午前１１時３３分

Connecting up 02

English

DeutschFrançais

Nederlands

Italiano Español Русский

Chapter 2:

Connecting up

Caution

• Before making or changing the connections,

switch off the power and disconnect the power cord

from the AC outlet.

• Connect the power cord after all the connections

between devices have been completed.

Analog audio output connections

By connecting this unit’s analog audio output to the

analog audio input of an amplifier, you can use the

amplifier to enjoy analog audio produced from this unit.

Digital audio output connections

If desired, the digital audio output from this unit can be

connected to an AV amplifier or digital recording device

(CD recorder, MD, etc.).

• This unit’s DIGITAL OUT terminals do not output

sound from SACD and DSD discs, nor from iPod/

iPhone/iPad devices.

Important

Care in the handling of optical fiber cables

• Do not allow optical fiber cables to be bent at sharp

angles. When storing optical fiber cables, roll in

coils of at least 15 cm diameter.

• When connecting optical fiber cables, align the

connectors correctly and insert fully. If the

orientation of the cable connector is incorrect and

excessive force is applied in the attempt to fasten

the connector, the connector may be deformed,

preventing the shutter from closing when the cable

is removed.

Note

• For digital audio output, CDs played on this unit

must produce linear PCM signals with a sampling

rate up to 44.1 kHz and quantitative bits up to 16

bits (some discs may not be playable depending on

the connected component and environment). For

information about other files, see page 12.

ANALOG

AUDIO INPUT

Amplifier

Audio cable (included)

PD-30’s rear panel

DIGITAL IN

OPTICAL

DIGITAL IN

COAXIAL

AV amplifier or

digital recording

device

Optical fiber cable

(commercially

available)

Coaxial digital

audio cable

(commercially

available)

PD-30’s rear panel

AV amplifier or

digital recording

device

Using centralized control with other

Pioneer components (PD-30 only)

This unit and other Pioneer components equipped with

CONTROL IN/OUT jacks can be controlled with a single

remote control by aiming the remote toward the signal

receptor on the AV amplifier or other component. This

also allows remote control of components not equipped

with a remote sensor, or installed in places where the

component’s remote sensor cannot be accessed.

Note

• For connections use a commercially available

monaural miniplug cord (without resistor).

• When connecting the CONTROL IN/OUT jacks,

commercially available audio cords must also be

used to make analog connections. Merely

connecting the CONTROL IN/OUT jacks alone will

not allow proper system control.

• When a control cord is connected to the PD-30’s

CONTROL IN jack, the unit cannot be controlled by

pointing the remote control at the PD-30 (the

remote sensor is automatically disabled).

Plugging in

Important

• If it is necessary to detach the power cord, first be

sure to press the 

STANDBY/ON button on the

front panel of the unit so the PD-30 is turned OFF or

the PD-10 is in standby mode before detaching the

cord.

• Confirm that the [-OFF-] indicator is not lighted in

the main unit’s front panel display before

disconnecting the power cord. If the power cord is

disconnected while the [-OFF-] indicator is still

lighted, the unit’s settings may revert to factory

defaults.

• When going on a trip or otherwise not using the

unit for an extended period, always disconnect the

power cord from its outlet.

Caution

• Do not use any power cord other than the one

supplied with this unit.

• Do not use the supplied power cord for any purpose

other than that described below.

After you’ve finished making all connections, plug the

unit into an AC outlet.

1 Plug the supplied power cord into the

AC IN

socket on the rear of the unit.

2 Plug the other end into AC outlet.

To other Pioneer

component equipped

with CONTROL IN jack

Remote control for

AV amplifier, etc.

Point the remote

control toward the

signal receiver on

the AV amplifier, etc.

Other Pioneer component

equipped with CONTROL

IN/OUT jacks

PD-30

To AC outlet

Power cord

PD-30’s rear panel

PD-30_PWSYXZT8.book 5 ページ２０１２年５月７日　月曜日　午前１１時３３分

Controls and displays03

Chapter 3:

Controls and displays

Remote control

 STANDBY/ON

Switches the amplifier between standby and on.

2 Number buttons

Use these buttons when you wish to specify a certain

track for playback. Use the number buttons to select the

track, then press ENTER to confirm the selection.

CLEAR

Press to clear the contents set for programmed playback

(page 8).

SETUP

Use to set the auto power down function (page 11).

///

Use these to select items, change settings and

move the cursor.

ENTER

Use this to implement the selected item or enter a

setting that you have changed.

iPod MENU

(PD-30 only)

Use when operating the iPod/iPhone/iPad menu.



Press to return to the beginning of the currently

playing track. Press twice to return to the beginning

of the previous track.



Press to start playback. During playback, pause/

unpause playback.



Press during playback to skip ahead to the

beginning of the next track.



Press to perform fast reverse on the currently

playing track. If the button is pressed again during

fast reverse, the reversing speed changes in four

steps.



Press to stop playback.



Press to perform fast forward on the currently

playing track. If the button is pressed again during

fast forward, the fast forward speed will change in

four steps.

iPod/USB

(PD-30)

USB (PD-10)

Press to switch the unit’s input to iPod or USB

(page 9,10).

PD-10

PD-30

SACD/CD

Press to switch the unit’s input to SACD/CD. In the case

of hybrid SACD discs, if this button is pressed when

playback is stopped, the disc's playback area changes

(page 11).

REPEAT

Press to initiate repeat play (page 8).

RANDOM

Press to initiate random play (page 8).

PROGRAM

Press to initiate programmed playback (page 8).

11 PURE AUDIO

Press this button to activate the Pure Audio mode. In this

mode, audio playback is performed with greatest fidelity

to the original sounds (page 11).

 OPEN/CLOSE

Press to open and close the disc tray (page 8).

ENTER

Use this to implement the selected item or enter a

setting that you have changed.

DISPLAY

Press to display various data about the disc, including

elapsed playing time and remaining playing time

(page 8).

DIMMER

Press to change the illumination levels for the main

unit’s front panel display and indicators (page 11).

S.RETRIEVER

Press to alternate between sound retriever function

settings(page 11).

 AMPLIFIER

(PD-10 only)

Press to switch the power between ON and STANDBY on

a Pioneer AV amplifier.

VOLUME +/–

(PD-10 only)

Press these buttons to adjust the sound volume of a

Pioneer AV amplifier.

MUTE

(PD-10 only)

Press to mute the sound on a Pioneer AV amplifier.

Press again to cancel the muting function.

INPUT

(PD-10 only)

Press to switch the input on a Pioneer AV amplifier.

Rear panel

See page 5 for details regarding connections.

CONTROL IN/OUT

jack (PD-30 only)

DIGITAL OUT (COAXIAL)

terminal

DIGITAL OUT (OPTICAL)

terminal

ANALOG OUT

terminals

AC IN

jack

PD-30

DIGITAL IN

1 2 3 54

PD-30_PWSYXZT8.book 6 ページ２０１２年５月７日　月曜日　午前１１時３３分

Controls and displays 03

English

DeutschFrançais

Nederlands

Italiano Español Русский

Front panel

/I STANDBY/ON

When power is turned on, the power indicator in the

center of the button will light.

• On the PD-30 model, this switches the amplifier

between off and on.

To turn power ON, press the button until it remains

in the depressed position.

• On the PD-10 model, this switches the amplifier

between standby and on.

STANDBY

indicator

Lights when power is in the STANDBY mode.

PURE AUDIO

indicator

Lights when Pure Audio function is ON (page 11).

4 Front panel display

(See the following description.)



Press to open and close the disc tray (page 8).

FUNCTION

Use to change the input source. The source changes as

below.

DISC  iPod*

/USB  Return to the beginning

(Undisplayed).

PD-30 only



Press to stop playback.



Press to start playback. During playback, pause/

unpause playback.

9 Remote sensor

Receives the signals from the remote control (page 4).

iPod/USB port

(PD-30)

USB port (PD-10)

Use to connect your Apple iPod/iPhone/iPad (page 9) or

connect a USB device (page 10).

11 Disc tray

(page 8)





Press to return to the beginning of the currently playing

track. Press twice to return to the beginning of the

previous track. When the button is held depressed, the

currently playing track will be reversed at fast speed.

• When pressed again during fast reverse, the speed

of fast reverse will change in four steps.

 

Press to advance to the beginning of the next track.

When the button is held depressed, the currently playing

track will be forwarded at fast speed.

• When pressed again during fast forward, the speed

of fast forward will change in four steps.

PD-30

3 5 6 7 81

2 4

10 12 1311

Front panel display

USB/iPod

Lights during playback of USB flash memory or iPod/

iPhone/iPad.

SACD/CD/DSD

The indicator lights corresponding to the currently

playing disc type.

PGM

Lights during programmed playback (page 8).

TRK

Lights when displaying the track number together with

either the elapsed playing time or remaining playing

time.

FILE

Lights when a file name is displayed.

REPEAT

Lights during repeat playback (page 8).

RANDOM

Lights during random playback (page 8).

ALL

Lights during disc-repeat playback (page 8).

TOTAL

Lights when the disc’s remaining playing time is

displayed.

REMAIN

Lights when displaying the remaining playing time for

track or disc.

S.RTRV

Lights when the sound retriever function is ON

(page 11).

SET UP

Lights when setting the auto power-down function

(page 11).



Lights during fast forward.



Lights during fast reverse.



Lights during playback.



Lights during pause mode.

14 Character display

1 2 4 5 6

1411 12 13

3 7 8 9

PD-30_PWSYXZT8.book 7 ページ２０１２年５月７日　月曜日　午前１１時３３分

Playback04

Chapter 4:

Playback

The functions that can be used differ according to the

type of disc and file. In some cases, some of the

functions cannot be used. See Playback functions on

page 11.

Playing discs

1 Press the front panel’s

/I STANDBY/ON

button to turn

power ON to the unit.

• With the PD-30, turn on the power by

pressing the POWER button in until it

remains at the depressed position.

Side view of front panel

2 Press the



button to

open the disc tray and set

the disc in place.

• Set the disc with the imprinted side facing up.

3 Press the



button

to begin playback.

• To pause playback, press

the  button.

• To stop playback, press the  button.

Note

• Steps 2 and 3 can be performed via the remote

control in the same way as for the main unit’s front

panel controls.

Set the power to Standby

Remove any disc loaded before setting the power switch

to STANDBY mode.

• Press the remote control’s

 STANDBY/ON

button.

The next time you wish to turn on the power,

press the remote control’s  STANDBY/ON button.

• In the case of the PD-30, pressing the front panel

/I STANDBY/ON button sets the unit to power

OFF, not STANDBY mode. To turn on the power

again, press the front panel’s /I STANDBY/ON

button.

Note

• If the power cord is disconnected when the unit is

in the standby mode the unit will turn off, but when

the cord is then reconnected, the unit will not

automatically turn on. After reconnecting the

power cord, press the remote control’s

 STANDBY/ON button to turn the power on.

Fast forward/Fast reverse

• During playback, press the





button.

Each time the button is pressed the

forward or reverse speed is changed in four steps.

• To return to the normal play function, press the

 button.

Skip function

• During playback, press the





button.

Playback will skip ahead or backwards the

number of tracks corresponding to the times the button

is pressed.

Direct search (designate a specific track

for playback)

• Using the number buttons,

input the desired track number,

then press the ENTER button to confirm the

selection.

Even if the ENTER button is not pressed,

playback will begin automatically after a 5-

second interval (this does not apply to

programmed playback).

Repeat playback

Repeat play can be performed for the currently playing

single track, or for all tracks on the entire disc.

• During playback, press the

REPEAT button.

• Repeat play will begin, and the [REPEAT] indicator

will light on the unit’s front panel display. Press the

button again to alternate the type of repeat play

between single-track repeat and disc (all-track)

repeat as follows:

Note

• The repeat play function is canceled when disc

playback is stopped.

Random playback

All tracks on the disc are selected and played in random

order, until each track has been played once.

• During playback, press the

RANDOM

button.

Random playback starts, and the [RANDOM]

lights in the main unit's front panel display.

Note

• Random playback continues until the disc stops, or

until the RANDOM button is pressed once again.

• The random playback function cannot be used

simultaneously with programmed playback.

•If the  button is pressed during random

playback, play skips ahead to the next randomly

selected track. If the  button is pressed,

playback returns to the beginning of the currently

playing track and starts again.

Programmed playback (Play tracks in a

predetermined order)

This function allows you to program up to 24 tracks for

playback in the order selected.

1 From the stop mode, press the

PROGRAM

button.

The [PGM] indicator will light in the unit’s front panel

display.

2 Use the number buttons to select the

number of the desired track,

followed by the

ENTER

button.

Example: To select track 15, press the 1 and 5

buttons, then press ENTER. In the event you

make a mistake, press the CLEAR button.

3 Repeat step 2 to input the numbers of all

desired tracks.

4 Press the



button.

Playback will begin in the order the tracks have

been programmed. If you wish to add other

tracks, repeat steps 1 and 2.

Note

•If the CLEAR button is pressed when the disc is

stopped, all programmed tracks will be cancelled.

• To clear programmed tracks, from the stop mode,

press the PROGRAM button followed by the CLEAR

button. The programmed tracks will be cancelled,

beginning with the last one programmed.

• A “pause” cannot be programmed.

• The contents of programmed playback (all-track

repeat) can be repeated. Just press the REPEAT

button after beginning programmed playback (see

at left).

• Single-track repeat cannot be performed during

programmed playback.

• Random playback cannot be used during

programmed playback.

•If the  button is pressed during programmed

playback, play will jump ahead to begin playback of

the next programmed track.

• After playback has stopped, to begin the same

programmed playback again, press the PROGRAM

button, followed by the  button.

View disc data

• During playback, press the

DISPLAY

button

Various data, including elapsed and remaining playing

times will be displayed.

Depending on the disc, pressing the DISPLAY button

multiple times will cause the display to cycle through

different data contents.

Note

• Displays file name (first 8 characters) when playing

AAC files (PD-30 only), WMA/MP3 files, or files on

DSD discs. Depending on the characters used,

however, the display may not be entirely correct.

single-track repeat

([REPEAT] indicator lights)

Disc repeat ([REPEAT] and [ALL] indicators light)

Repeat OFF

0 9

ENTER

REPEAT

RANDOM

PROGRAM

DISPLAY

0 9

ENTER

PD-30_PWSYXZT8.book 8 ページ２０１２年５月７日　月曜日　午前１１時３３分

Playback 04

English

DeutschFrançais

Nederlands

Italiano Español Русский

iPod/USB

iPod/iPhone/iPad playback

(PD-30 only)

Merely by connecting your iPod/iPhone/iPad to this unit,

you can enjoy high-quality sound from your iPod/iPhone/

iPad.

Confirm what iPod/iPhone/iPad models are

supported

The iPod/iPhone/iPad playable on this unit are shown

below.

• This system has been developed and tested for the

software version of iPod/iPhone/iPad indicated on

the website of Pioneer.

• Installing software versions other than indicated on

the website of Pioneer to your iPod/iPhone/iPad

may result in incompatibility with this system.

Note

• Pioneer does not guarantee that this unit plays

iPod/iPhone/iPad models other than the ones

specified.

• Some functions may be restricted depending on

the model or software version.

• iPod/iPhone/iPad is licensed for reproduction of

non-copyrighted materials or materials the user is

legally permitted to reproduce.

• Features such as the equalizer cannot be controlled

using this system, and we recommend switching

the equalizer off before connecting.

• Pioneer cannot under any circumstances accept

responsibility for any direct or indirect loss arising

from any inconvenience or loss of recorded

material resulting from iPod/iPhone/iPad failure.

• For detailed instructions on using the iPod/iPhone/

iPad, please refer to the manual supplied with the

iPod/iPhone/iPad.

Playing your iPod/iPhone/iPad

1Press

iPod/USB

on the remote

control to select

iPod

as the input

source.

Press the remote control’s iPod/USB button.

• You can also perform the same operation by

pressing the FUNCTION on the front panel

repeatedly.

2 Connect your iPod/iPhone/iPad.

Connect your iPod/iPhone/iPad to the USB port on the

unit’s front panel. Use the iPod cable supplied with your

iPod/iPhone/iPad for the connection.

• For the cable connection, also refer to the operating

instructions for your iPod/iPhone/iPad.

iPod/iPhone/iPad Audio Control

iPod nano 2/3/4/5/6G 

iPod touch 1/2/3/4G 

iPhone 

iPhone 3G/3GS 

iPhone 4/4S 

iPad



iPad 2



iPod/iPhone/iPad

iPod cable

The following operations are possible for iPod/iPhone/

iPad.

Important

If this unit cannot play your iPod/iPhone/iPad, perform

the following troubleshooting checks:

• Check whether the iPod/iPhone/iPad is supported

by this unit.

• Reconnect the iPod/iPhone/iPad to the unit. If this

doesn’t seem to work, try resetting your iPod/

iPhone/iPad.

• Check the iPod/iPhone/iPad software is supported

by this unit.

If the iPod/iPhone/iPad cannot be operated, check the

following items:

• Is the iPod/iPhone/iPad connected correctly?

Reconnect the iPod/iPhone/iPad to the unit.

• Is the iPod/iPhone/iPad experiencing a hangup? Try

resetting the iPod/iPhone/iPad, and reconnect it to

the unit.

Note

• iPod/iPhone/iPad recharging occurs whenever an

iPod/iPhone/iPad is connected to this unit.

(Recharging is enabled only when the unit’s power

is turned ON.) (does not apply when pure audio

function is ON)

• When input is switched from iPod to another

function, the iPod/iPhone/iPad’s playback will be

stopped automatically.

Button What it does



Starts playback. During playback, pause/

unpause playback.



Pauses playback.



Press to skip to the start of the current file,

then previous files.



Hold depressed for fast reverse.



Press to skip to the next file.



Hold depressed for fast forward.

RANDOM

The currently selected iPod/iPhone/iPad

files are played back in random order

(shuffle play).

REPEAT

The currently selected iPod/iPhone/iPad

files are played back repeatedly.

1Each time you press REPEAT the repeat modes

changes as below.

Repeat 1  Repeat all  Normal playback

Repeat 1: Repeats a file currently played back.

Repeat all: Repeats all files.

iPod MENU

Use when operating the iPod/iPhone/iPad

menu.

/

ENTER

Use to perform iPod/iPhone/iPad menu

operations.

PD-30_PWSYXZT8.book 9 ページ２０１２年５月７日　月曜日　午前１１時３３分

Playback04

Playing files stored on USB storage

devices

1 Press

USB

on the remote control

to select USB as the input source.

Press the remote control’s iPod/USB button

(PD-30) or press the remote control

’

USB

button

(PD-10)

• You can also perform the same operation by

pressing the FUNCTION on the front panel

repeatedly.

2 Connect the USB storage device.

3 Press the



button to begin playback.

• To pause playback, press the  button.

• To stop playback, press the  button.

You can perform the following operations. Note that

some buttons are not available for operation depending

on the category currently being played back.

When the auto power down function is set to ON, and

input is set for USB memory playback, if playback from

the USB memory device stops for 30 minutes without

other operation being performed, the power will

automatically switch to standby.

Note

• This unit may not recognize the USB storage

device, play files or supply power to the USB

storage device. For details, see Additional

information on page 12.

• Pioneer does not guarantee that any file recorded

on a USB storage device will play or that power will

be supplied to a USB storage device. Also note that

Pioneer will accept no responsibility whatsoever for

loss of files on USB storage devices caused by

connection to this unit.

• This unit does not support use of a USB hub.

USB storage device

(commercially available)

Button What it does



Starts playback. During playback, pause/

unpause playback.



Stops playback.



Press to skip to the start of the current file,

then previous files.



Press for fast reverse. Each time button is

pressed, reverse speed changes in four

steps.



Press to skip to the next file.



Press for fast forward. Each time button is

pressed, forward speed changes in four

steps.

RANDOM

The currently selected files are played back

in random order (shuffle play).

REPEAT

The currently selected files are played

repeatedly.

1Each time you press REPEAT the repeat modes

changes as below.

Repeat 1

 Repeat all  Normal playback

Repeat 1: Repeats a file currently played back.

Repeat all: Repeats all files.

iPod/USB

PD-30_PWSYXZT8.book 10 ページ２０１２年５月７日　月曜日　午前１１時３３分

Using advanced functions 05

English

DeutschFrançais

Nederlands

Italiano Español Русский

S.RETRIEVER

PURE AUDIO

SACD/CD

DIMMER

SET UP

ENTER

Chapter 5:

Using advanced functions

The functions that can be used differ according to the

type of disc and file. In some cases, some of the

functions cannot be used. See Playback functions on the

right column.

Playing with high-fidelity sound

Sound Retriever

When compressed sound signals are decompressed for

playback, some parts experience dropouts. By setting

the sound retriever function to ON, compensation is

added for those losses, thus producing richer, more

sumptuous sound.

• Press the S.RETRIEVER button.

Each time the button is pressed, the function

will change as follows: S.RTRV: OFF  S.RTRV: LOW 

S.RTRV: HI  Returns to original status

• The sound retriever function is disabled when the

pure audio function is ON.

Pure Audio

This function disables digital audio output and plays

analog audio with high fidelity. When set to ON, the

display shows no indicators. The factory default

condition is OFF.

• Press the PURE AUDIO button.

Press again to turn the function OFF.

• When this function is set to ON and the main unit’s

input is switched to SACD/CD, the PURE AUDIO

indicator will light on the front panel. During disc

playback, the front panel display turns OFF.

• When the PURE AUDIO indicator is lighted, any

iPod/iPhone/iPad connected to the main unit will

not be recharged.

Changing the playback area (layer) of

an SACD/CD

Hybrid SACD discs are composed of two layers, an

SACD layer, and CD layer, allowing you to select which

layer you wish to play.

1 Press the

SACD/CD

button.

Input changes to SACD/CD.

2 In the stop mode, press the SACD/CD

button.

Each time the button is pressed, the playback alternates

between the CD area and SACD 2 channel area.

Note

• This unit does not support SACD multi-channel

areas.

Adjusting overall display illumination

This unit is equipped with a dimmer function to allow the

display illumination to be adjusted in three levels,

responding to differing levels of ambient lighting. The

factory default is the brightest setting.

• Press the

DIMMER

button.

Each time the button is pressed it the brightness

cycles through the three levels.

• The dimmer setting cannot be changed when a

disc is playing with the pure audio function ON (see

at left).

• The brightness of the STANDBY indicator does not

change.

Auto power down (automatically sets

power to standby)

This function automatically switches the unit to standby

mode if no signal or switch operation is detected for 30

minutes.

1 Press the

SET UP

button.

2 Change the setting and confirm.

Use the / button to set the function ON

or OFF as desired, then press the ENTER

button to confirm.

Note

• This function is disabled when iPod input is

selected.

Playback functions

The functions that can be used differ according to the type of disc and file. In some cases, some of the functions

cannot be used. Check the usable functions on the table below.

Function

1 Some functions may not work for some discs or files, even if indicated [] on the table.

Disc/file type

SACD CD-DA

CD-R/-RW

2 Also see Playback of CD-R/CD-RW discs on page 12.

WMA

MP3

AAC

3 • AAC files can be played back only on the PD-30.

• Also see Playable file formats on page 12.

DSD

4 Also see Playing DSD discs on page 12.

Fast forward/Fast reverse



Skip function



Direct search

(designate a specific track for playback)

 ––

Repeat playback



Random playback



Programmed playback

(Play tracks in a predetermined order)

 ––

View disc data



Sound Retriever

–– –

Pure Audio





5 This function is enabled only during playback of files recorded on disc.



SACD/CD



6 Hybrid SACD discs only.

–––

PD-30_PWSYXZT8.book 11 ページ２０１２年５月７日　月曜日　午前１１時３３分

Additional information06

Chapter 6:

Additional information

Playable disc

Playback of CD-R/CD-RW discs

• This unit can play CD-R/CD-RW discs recorded with

CD music format, or audio data in WMA and MP3

format. However, some discs may not be playable,

or may generate noise or distorted sound.

• This unit is for playback only. It cannot record data

on CD-R/CD-RW discs.

• CD-R/CD-RW discs which have not be finalized

cannot be played on this unit. For details, consult

the operating instructions for your disc recorder.

Playing DSD discs

This unit can play DSD disc files recorded in the DSF file

format.

Playable files

• Recorded discs: DVD-R/-RW

• File Extension: .dsf

• Folder name: DSD_DISC

• Capacity: maximum 4 GB per file

• Audio: 2-channel

• Sampling frequency: 2.8224 MHz

Example of folder composition

The order of file/folder playback is not alphabetical, but

depends on the order in which they were recorded to the

disc.

• A single folder can hold a maximum of 150 files.

• A single disc can hold a maximum of 200 folders.

• Each folder should have no more than 8 levels.

• File names using Japanese language fonts and

certain other symbol fonts may not be displayed

correctly.

• Any files other than those of DSF format will be

ignored.

Caution

• Some files may not be playable.

• Discs holding large numbers of files and folders

may require substantial time to begin playback. In

this case, you can move the desired files directly to

the DSD_DISC folder, or limit the number of files to

20 or less.

Operations during playback

The following operations cannot be performed during

playback of a DSD disc:

•Direct search

• Playback of disc files other than DSF type

Display

When the unit is in the stop mode when playing a DSD

disc, the unit will display the indicator [DSD DISC].

During playback, pressing the DISPLAY button will

cause the display to cycle through the following

information each time the button is pressed:

• Number of the track and its elapsed playing time

• Name of file

Root DSD_DISC

FolderA

File01.dsf

FolderB

File02.dsf

FolderD

File03.dsf

FolderC

File04.dsf

File05.dsf

File06.dsf

Playable file formats

Playing audio files

This unit supports the following file formats.

• Note that some file formats are not available for

playback although they are listed as playable file

formats.

• If an attempt is made to play files with unsupported

formats, the sound may be intermittent or be

accompanied by noise. In such cases, confirm that

the file format is compatible with this unit.

• Music files subjected to Digital Rights

Management controls cannot be played. DRM

(Digital Rights Management) copy protection is a

technology designed to protect copyrights. To

prevent illegal copying DRM restricts playback to

the disc recorder or computer originally used to

record the music. For details, consult the operating

instructions and help files for the device or

application used during the original recording.

Caution

• It may not be possible to play all CD-R/CD-RW discs

recorded on a CD recorder or computer, due to

characteristics of the disc, disc scratches or

soiling, or soiling or condensation on the player’s

laser lens.

• Discs recorded on a computer may not be playable

on this unit due to application settings or computer

environment. Be sure to record your discs using the

proper format (for details consult the marketer of

your application).

• Discs recorded in packet write format cannot be

played on this unit.

• CD-R/CD-RW discs that have not be finalized

cannot be played on this unit.

WMA file playback

• Please use discs recorded to compatibility with CD-

ROM file systems (ISO9660 level 1 and 2), and those

compatible with extended format (Joliet, Romeo).

• This unit does not support discs recorded with

Variable Bit Rate (VBR) or lossless encoding.

• This unit does not support multi-session discs.

• A total maximum of 648 folders and tracks can be

recognized and played. Of that number, a

maximum of 299 may be folders. However,

depending on the folder composition, not all folders

and tracks can be recognized and played.

• When using WMA files, be sure they have been

encoded using applications verified and recognized

by Microsoft Corporation. If unrecognized

applications are used, improper operation may

result.

Category

Extension

Stream

PD-30_PWSYXZT8.book 12 ページ２０１２年５月７日　月曜日　午前１１時３３分

Additional information 06

English

DeutschFrançais

Nederlands

Italiano Español Русский

MP3 file playback

• Please use discs recorded to compatibility with CD-

ROM file systems (ISO9660 level 1 and 2), and those

compatible with extended format (Joliet, Romeo).

• This unit does not support Variable Bit Rate (VBR);

(even if files are playable, the times shown in the

front panel display will be incorrect due to the

change in bitrate, thus changing faster or slower

than the correct time values.)

• This unit does not support multi-session discs.

• A total maximum of 648 folders and tracks can be

recognized and played. Of that number, a

maximum of 299 may be folders. However,

depending on the folder composition, not all folders

and tracks can be recognized and played.

• For optimum sound quality, bit rates of 128 kbps or

higher are recommended for recordings.

MPEG-4 AAC file playback

• AAC is an acronym for “Advanced Audio Coding,”

the basic format for audio compression technology

used in MPEG-2 and MPEG-4.

• This unit supports the playback of AAC files with

the extension “.m4a,” as encoded by iTunes®.

However, playback may not be possible in the case

of files copy protected by DRM, and depending on

the iTunes encoding version.

• iTunes is a trademark of Apple Inc., registered in

the U.S. and other countries.

Cautions on use

Moving the player

When moving this unit to a new location, always perform

the following procedure first: Remove any disc loaded

and close the disc tray. Press the unit’s /I STANDBY/

ON button so that the [-OFF-] appears in the front panel

display, then wait ten seconds before disconnecting the

power cord. Damage or malfunctions may result if the

unit is moved with a disc loaded in the tray.

Place of installation

Select a stable place near the TV and AV system to which

the unit is connected.

Do not place the player on top of a TV or color monitor.

Keep it away from cassette decks or other components

easily affected by magnetism.

Avoid the following types of places:

• Places exposed to direct sunlight

• Humid or poorly ventilated places

• Extremely hot or cold places

• Places subject to vibration

• Places in which there is much dust or cigarette

smoke

• Places exposed to soot, steam or heat (in kitchens,

etc.)

Do not mount the unit on a sofa or other object or

material with absorbent qualities, since sound quality

may be adversely affected.

Do not place objects on top

Do not place objects on top of the player.

Keep away from heat

Do not place the player on top of an amplifier or other

device generating heat. When installing in a rack, to

avoid the heat generated by the amplifier and other

devices, place it on a shelf below the amplifier whenever

possible.

Turn the power off when not using the

player

Depending on the conditions of the TV broadcast

signals, striped patterns may appear on the screen when

the TV is turned on while the player’s power is turned on.

This is not a malfunction with the player or TV. If this

happens, turn the player’s power off. In the same way,

noise may be heard in the sound of a radio.

Condensation

If the player is moved suddenly from a cold place into a

warm room (in winter, for example) or if the temperature

in the room in which the player is installed rises

suddenly due to a heater, etc., water droplets

(condensation) may form inside (on operating parts and

the lens). When condensation is present, the player will

not operate properly and playback is not possible. Let the

player stand at room temperature for 1 or 2 hours with

the power turned on (the time depends on the extent of

condensation). The water droplets will dissipate and

playback will become possible.

Condensation can also occur in the summer if the player

is exposed to the direct wind from an air-conditioner. If

this happens, move the player to a different place.

Cleaning the player

Normally, wipe the player with a soft cloth. For tough dirt,

apply some neutral detergent diluted in 5 to 6 parts water

to a soft cloth, wring out thoroughly, wipe off the dirt,

then wipe again with a dry cloth.

Note that getting alcohol, thinner, benzene or

insecticide on the player could cause the print and

coating to peel off. Also, avoid leaving rubber or vinyl

products in contact with the player for long periods of

time, as this could damage the cabinet.

When using chemical-impregnated wipes, etc., read the

wipe’s cautions carefully.

Unplug the power cord from the power outlet when

cleaning the player.

Caution for when the unit is installed in a

rack with a glass door

Do not press the  OPEN/CLOSE on the remote control

to open the disc tray while the glass door is closed. The

door will hamper the movement of the disc tray, and the

unit could be damaged.

Cleaning the pickup lens

The player’s lens should not become dirty in normal use,

but if for some reason it should malfunction due to dust

or dirt, consult your nearest Pioneer authorized service

center. Although lens cleaners for players are

commercially available, we advise against using them

since some may damage the lens.

Handling discs

Do not use damaged (cracked or warped) discs.

Do not scratch the disc’s signal surface or let it get dirty.

Do not load more than one disc into the player at a time.

Do not glue paper or put stickers onto the disc, or use a

pencil, ball-point pen or other sharp-tipped writing

instrument. These could all damage the disc.

Storing discs

Always store discs in their cases, and place the cases

vertically, avoiding places exposed to high temperatures

or humidity, direct sunlight or extremely low

temperatures.

Be sure to read the cautions included with the disc.

Cleaning discs

It may not be possible to play the disc if there are

fingerprints or dust on it. In this case, using a cleaning

cloth, etc., to wipe the disc gently from the center toward

the outer edge. Do not use a dirty cleaning cloth.

Do not use benzene, thinner or other volatile chemicals.

Also do not use record spray or antistatic agents.

For tough dirt, apply some water to a soft cloth, wring out

thoroughly, wipe off the dirt, then wipe off the moisture

with a dry cloth.

Specially shaped discs

Specially shaped discs (heart-shaped, hexagonal, etc.)

cannot be used on this player. Never use such discs, as

they will damage the player.

Condensation on discs

If the disc is moved suddenly from a cold place into a

warm room (in winter, for example), water droplets

(condensation) may form on the disc surface. Discs will

not play properly if there is condensation on them.

Carefully wipe off the water droplets from the disc

surface before using the disc.

PD-30_PWSYXZT8.book 13 ページ２０１２年５月７日　月曜日　午前１１時３３分

Additional information06

Troubleshooting

Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with

this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other

components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks

listed below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.

• If the unit does not operate normally due to external effects such as static electricity disconnect the power plug

from the outlet and insert again to return to normal operating conditions.

Problem Remedy

The disc won’t play or is automatically

ejected after loading.

• Make sure the disc is loaded with the label side face-up and aligned properly in the

disc tray guide (page 8).

• Make sure the disc is free from dirt and dust and is not damaged (page 13).

• Condensation inside the player: Allow time for condensation to evaporate. Avoid

using the player near an air-conditioning unit (page 13).

• The disc tray will open if an unsupported disc type is loaded (page 4).

Cannot play CD-R/-RW discs. • Some CD-R/-RW discs recorded on a computer cannot be played.

Cannot play files in WMA/MP3 or AAC

format (PD-30 only).

• The following types of files cannot be played:

- Files with DRM copy protection

- Recorded discs not in compliance with ISO9660 format

- Files not recorded with sampling frequency of 44.1 kHz

- WMA files recorded with variable bit rate (VBR) or lossless encoding.

Cannot operate the remote

control.

• Replace the battery (page 4).

• Operate within 7 m, 30

of the remote sensor on the front panel (page 4).

• Remove the obstacle or operate from another position.

• Avoid exposing the remote sensor on the front panel to direct light.

• Is the control cord for one component connected improperly? Confirm correct

connections (page 5).

Settings are erased. • If the power cord is forcibly disconnected or a power failure occurs while the unit’s

power is ON, previously entered settings may be deleted. To disconnect the power

cord, first press the remote control's

 STANDBY/ON

button, then wait until the

[-OFF-] goes out in the front panel display; only then disconnect the cord. Particular

care should be taken when the unit's power cord is connected to an outlet on another

component, since turning off the power to the other component may simultaneously

disconnect power to this unit. Whenever possible, connect this unit's power cord

directly to a wall outlet.

No audio, or audio is distorted. • Check that all interconnects are firmly inserted (page 5).

• Check that the plugs and terminals are free of dirt, oxide, etc. and clean if necessary.

Also check the cable for damage.

• Check that the disc is not damaged, and free from dust and dirt.

• Is the unit set to “pause”? Press the



button.

• Check your amplifier/receiver’s settings (volume, input function, speaker settings,

etc.).

• Make sure the player’s output is not connected to the amplifier’s phono (turntable)

inputs.

Noticeable difference in SACD and

CD volume.

• This is due to differences in the audio format and is not a malfunction.

Between tracks of an SACD disc, the

main unit's display indicates [--:--].

• This display may occur depending on the disc.

The analog audio is OK, but there

appears to be no digital audio signal.

• Make sure that Pure Audio feature is switched off (page 11).

• Audio from SACD and DSD discs, as well as iPod cannot be output in digital form.

Use the

ANALOG OUT

terminals for such media (page 5).

USB storage device is not recognized. • Connect the device securely (all the way in) (page 10).

• This unit does not support USB hubs. Connect the USB storage device directly.

• Some USB storage devices may not be recognized properly. Turn the power off then

back on.

• This unit only supports USB mass storage class devices.

• Only the FAT16 and FAT32 file systems are supported. Other file systems (ex. FAT,

NTFS, etc.) are not supported.

• This device does not support the use of external hard disc drives.

A USB storage device is connected

and displayed, but the audio files

stored on the USB storage device

cannot be played back.

• Copyrighted audio files stored on a USB storage device cannot be played back.

Attempting to import music data from a CD, etc., to a computer may cause the

invocation of copy protection, depending on the settings.

• See the list of file formats that can be played back on this unit.

Much time is required to recognized

the USB storage device.

• Some time may be required to load the data when large capacity USB storage

devices are connected (this could take several minutes).

Power is not supplied to the USB

storage device.

• When the pure audio function is set to ON, power is not supplied to

USB

ports

(page 11).

• Does an error message appear in the front panel display? (page 7)

- Turn the power off then back on (page 8).

- Turn the power off, then disconnect and reconnect the USB storage device

(page 10).

- Press

FUNCTION

to switch to the other mode, then switch again to the USB mode.

(When the input is switched back to USB) (page 7).

Music files are played back even

though they’re not recorded in the

USB storage device.

• Confirm whether any hidden files are recorded on the device. Hidden files will be

played.

Cannot operate the iPod/iPhone/iPad. • Make sure the iPod/iPhone/iPad is connected correctly (refer to

iPod/iPhone/iPad

playback (PD-30 only)

on page 9). Also, try disconnecting the iPod/iPhone/iPad then

reconnecting it.

• Confirm that the connected iPod/iPhone/iPad is a model supported by this unit

(page 9).

• If the iPod/iPhone/iPad is experiencing a hangup, try resetting the iPod/iPhone/iPad,

and reconnect it to the unit.

Power is not supplied to the iPod/

iPhone/iPad.

• When the pure audio function is set to ON, power is not supplied to

USB

ports

(page 9).

• Does an error message appear in the front panel display? Turn the power off, then

disconnect and reconnect the iPod/iPhone/iPad.

Sound not produced from iPod/

iPhone/iPad.

• Is sound being produced from the speaker of the iPod/iPhone/iPad? Disconnect

power to the unit, then turn on again. After setting for iPod input, connect the iPod/

iPhone/iPad.

• Audio is not output from the

DIGITAL OUT

terminals.

Problem Remedy

PD-30_PWSYXZT8.book 14 ページ２０１２年５月７日　月曜日　午前１１時３３分

Additional information 06

English

DeutschFrançais

Nederlands

Italiano Español Русский

Specifications

General

System. . . . . . . . . . . . . . . . . . . . . .Super Audio CD player

Power requirements. . . .AC 220 V to 240 V , 50 Hz/60 Hz

Power consumption

PD-30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 W

PD-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 W

Power consumption (standby) . . . . . . . . . . . . . . . 0.45 W

Weight

PD-30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.6 kg

PD-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2 kg

Dimensions

. . . . . . . . . . . . . 435 mm (W) x 128 mm (H) x 329 mm (D)

Operating temperature . . . . . . . . . . . . . +5 °C to +35 °C

Operating humidity . . . . . . . . . . . . . . . . . . . . 5 % to 85 %

(no condensation)

Audio output (1 stereo pair)

Output level. . . . . . . . . . . . . . . . . . . . During audio output

200 mVrms (1 kHz, –20 dB)

Number of channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RCA

Digital audio characteristics

Frequency response

CD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Hz to 20 kHz

SACD . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Hz to 50 kHz

S/N ratio

CD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 dB

SACD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 dB

Dynamic range

CD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 dB

SACD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 dB

Total harmonic distortion:

CD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.0022 %

SACD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.0020 %

Wow and flutter . . . . . . . . . . . . . . Limit of measurement

(±0.001 % W. PEAK) or lower

Digital output

Optical digital output . . . . . . . . . .Optical digital terminal

Coaxial digital output . . . . . . . . . . . . . . . . . .RCA terminal

Accessories

RCA audio cable (red/white plugs) . . . . . . . . . . . . . . . . . 1

Remote control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

AAA/IEC R03 dry cell batteries . . . . . . . . . . . . . . . . . . . . 2

Power cord

Warranty card (European model only)

Operating Instructions (This document)

Note

• Specifications and the design are subject to

possible modifications without notice, due to

improvements.

• Corporation and product names mentioned herein

are trademarks or registered trademarks of the

respective corporations.

PD-30_PWSYXZT8.book 15 ページ２０１２年５月７日　月曜日　午前１１時３３分

Ce point d’exclamation, placé dans un

triangle équilatéral, a pour but d’attirer

l’attention de l’utilisateur sur la présence,

dans les documents qui accompagnent

l’appareil, d’explications importantes du

point de vue de l’exploitation ou de

l’entretien.

Ce symbole de l’éclair, placé dans un

triangle équilatéral, a pour but d’attirer

l’attention de l’utilisateur sur la présence, à

l’intérieur du coffret de l’appareil, de

“tensions dangereuses” non isolées d’une

grandeur suffisante pour représenter un

risque d’électrocution pour les êtres

humains.

ATTENTION :

POUR ÉVITER TOUT RISQUE

D’ÉLECTROCUTION, NE PAS ENLEVER LE

COUVERCLE (NI LE PANNEAU ARRIÈRE).

AUCUNE PIÈCE RÉPARABLE PAR

L’UTILISATEUR NE SE TROUVE À

L’INTÉRIEUR. CONFIER TOUT ENTRETIEN À

UN PERSONNEL QUALIFIÉ UNIQUEMENT.

ATTENTION

DANGER D´ELECTROCUTION

NE PAS OUVRIR

IMPORTANT

D3-4-2-1-1_A1_Fr

AVERTISSEMENT

Cet appareil n’est pas étanche. Pour éviter les risques

d’incendie et de décharge électrique, ne placez près de

lui un récipient rempli d’eau, tel qu’un vase ou un pot

de fleurs, et ne l’exposez pas à des gouttes d’eau, des

éclaboussures, de la pluie ou de l’humidité.

D3-4-2-1-3_A1_Fr

AVERTISSEMENT

Avant de brancher l’appareil pour la première, lisez

attentivement la section suivante.

La tension de l’alimentation électrique disponible

varie selon le pays ou la région. Assurez-vous que

la tension du secteur de la région où l’appareil sera

utilisé correspond à la tension requise (par ex. 230

V ou 120 V), indiquée sur le panneau arrière.

D3-4-2-1-4*_A1_Fr

AVERTISSEMENT

Pour éviter les risques d’incendie, ne placez aucune

flamme nue (telle qu’une bougie allumée) sur

l’appareil.

D3-4-2-1-7a_A1_Fr

PRÉCAUTION DE VENTILATION

Lors de l’installation de l’appareil, veillez à laisser un

espace suffisant autour de ses parois de manière à

améliorer la dissipation de chaleur (au moins 10 cm sur

le dessus, 10 cm à l’arrière et 10 cm de chaque côté).

AVERTISSEMENT

Les fentes et ouvertures du coffret sont prévues pour la

ventilation, pour assurer un fonctionnement stable de

l’appareil et pour éviter sa surchauffe. Pour éviter les

risques d’incendie, ne bouchez jamais les ouvertures et

ne les recouvrez pas d’objets, tels que journaux, nappes

ou rideaux, et n’utilisez pas l’appareil posé sur un tapis

épais ou un lit.

D3-4-2-1-7b*_A1_Fr

K058a_A1_Fr

Information à destination des utilisateurs sur la collecte et l’élimination des

équipements et batteries usagés

Ces symboles qui figurent sur les produits, les emballages et/ou les documents

d’accompagnement signifient que les équipements électriques et électroniques et

batteries usagés ne doivent pas être jetés avec les déchets ménagers et font l’objet

d’une collecte sélective.

Pour assurer l’enlèvement et le traitement appropriés des produits et batteries

usagés, merci de les retourner dans les points de collecte sélective habilités

conformément à la législation locale en vigueur.

En respectant les circuits de collecte sélective mis en place pour ces produits, vous

contribuerez à économiser des ressources précieuses et à prévenir les impacts

négatifs éventuels sur la santé humaine et l’environnement qui pourraient résulter

d’une mauvaise gestion des déchets.

Pour plus d’information sur la collecte et le traitement des produits et batteries

usagés, veuillez contacter votre municipalité, votre service de gestion des déchets

ou le point de vente chez qui vous avez acheté ces produits.

Ces symboles ne sont valables que dans les pays de l’Union Européenne.

Pour les pays n’appartenant pas à l’Union Européenne :

Si vous souhaitez jeter ces articles, veuillez contacter les autorités ou revendeurs

locaux pour connaître les méthodes d’élimination appropriées.

Exemples de marquage

pour les batteries

Marquage pour les

équipements

Ce point d’exclamation, placé dans un

triangle équilatéral, a pour but d’attirer

l’attention de l’utilisateur sur la présence,

dans les documents qui accompagnent

l’appareil, d’explications importantes du

point de vue de l’exploitation ou de

l’entretien.

Ce symbole de l’éclair, placé dans un

triangle équilatéral, a pour but d’attirer

l’attention de l’utilisateur sur la présence, à

l’intérieur du coffret de l’appareil, de

“tensions dangereuses” non isolées d’une

grandeur suffisante pour représenter un

risque d’électrocution pour les êtres

humains.

ATTENTION :

POUR ÉVITER TOUT RISQUE

D’ÉLECTROCUTION, NE PAS ENLEVER LE

COUVERCLE (NI LE PANNEAU ARRIÈRE).

AUCUNE PIÈCE RÉPARABLE PAR

L’UTILISATEUR NE SE TROUVE À

L’INTÉRIEUR. CONFIER TOUT ENTRETIEN À

UN PERSONNEL QUALIFIÉ UNIQUEMENT.

ATTENTION

DANGER D´ELECTROCUTION

NE PAS OUVRIR

IMPORTANT

D3-4-2-1-1_A1_Fr

AVERTISSEMENT

Cet appareil n’est pas étanche. Pour éviter les risques

d’incendie et de décharge électrique, ne placez près de

lui un récipient rempli d’eau, tel qu’un vase ou un pot

de fleurs, et ne l’exposez pas à des gouttes d’eau, des

éclaboussures, de la pluie ou de l’humidité.

D3-4-2-1-3_A1_Fr

AVERTISSEMENT

Avant de brancher l’appareil pour la première, lisez

attentivement la section suivante.

La tension de l’alimentation électrique disponible

varie selon le pays ou la région. Assurez-vous que

la tension du secteur de la région où l’appareil sera

utilisé correspond à la tension requise (par ex. 230

V ou 120 V), indiquée sur le panneau arrière.

D3-4-2-1-4*_A1_Fr

AVERTISSEMENT

Pour éviter les risques d’incendie, ne placez aucune

flamme nue (telle qu’une bougie allumée) sur

l’appareil.

D3-4-2-1-7a_A1_Fr

PRÉCAUTION DE VENTILATION

Lors de l’installation de l’appareil, veillez à laisser un

espace suffisant autour de ses parois de manière à

améliorer la dissipation de chaleur (au moins 10 cm sur

le dessus, 10 cm à l’arrière et 10 cm de chaque côté).

AVERTISSEMENT

Les fentes et ouvertures du coffret sont prévues pour la

ventilation, pour assurer un fonctionnement stable de

l’appareil et pour éviter sa surchauffe. Pour éviter les

risques d’incendie, ne bouchez jamais les ouvertures et

ne les recouvrez pas d’objets, tels que journaux, nappes

ou rideaux, et n’utilisez pas l’appareil posé sur un tapis

épais ou un lit.

D3-4-2-1-7b*_A1_Fr

K058a_A1_Fr

Information à destination des utilisateurs sur la collecte et l’élimination des

équipements et batteries usagés

Ces symboles qui figurent sur les produits, les emballages et/ou les documents

d’accompagnement signifient que les équipements électriques et électroniques et

batteries usagés ne doivent pas être jetés avec les déchets ménagers et font l’objet

d’une collecte sélective.

Pour assurer l’enlèvement et le traitement appropriés des produits et batteries

usagés, merci de les retourner dans les points de collecte sélective habilités

conformément à la législation locale en vigueur.

En respectant les circuits de collecte sélective mis en place pour ces produits, vous

contribuerez à économiser des ressources précieuses et à prévenir les impacts

négatifs éventuels sur la santé humaine et l’environnement qui pourraient résulter

d’une mauvaise gestion des déchets.

Pour plus d’information sur la collecte et le traitement des produits et batteries

usagés, veuillez contacter votre municipalité, votre service de gestion des déchets

ou le point de vente chez qui vous avez acheté ces produits.

Ces symboles ne sont valables que dans les pays de l’Union Européenne.

Pour les pays n’appartenant pas à l’Union Européenne :

Si vous souhaitez jeter ces articles, veuillez contacter les autorités ou revendeurs

locaux pour connaître les méthodes d’élimination appropriées.

Exemples de marquage

pour les batteries

Marquage pour les

équipements

Nous vous remercions pour cet achat d’un produit Pioneer.

Nous vous demandons de lire soigneusement ce mode d’emploi ; vous serez ainsi à même de faire fonctionner l’appareil correctement. Après avoir bien lu le

mode d’emploi, le ranger dans un endroit sûr pour pouvoir s’y référer ultérieurement.

PD-30_PWSYXZT8-Fr.book Page 2 Wednesday, May 9, 2012 4:05 PM

NOTE IMPORTANTE SUR LE CABLE D’ALIMENTATION

Tenir le câble d’alimentation par la fiche. Ne pas

débrancher la prise en tirant sur le câble et ne pas

toucher le câble avec les mains mouillées. Cela risque de

provoquer un court-circuit ou un choc électrique. Ne pas

poser l’appareil ou un meuble sur le câble. Ne pas pincer

le câble. Ne pas faire de noeud avec le câble ou l’attacher

à d’autres câbles. Les câbles d’alimentation doivent être

posés de façon à ne pas être écrasés. Un câble abîmé

peut provoquer un risque d’incendie ou un choc

électrique. Vérifier le câble d’alimentation de temps en

temps. Contacter le service après-vente PIONEER le plus

proche ou le revendeur pour un remplacement.

S002*_A1_Fr

Si la fiche d’alimentation secteur de cet appareil ne

convient pas à la prise secteur à utiliser, la fiche doit

être remplacée par une appropriée. Ce

remplacement et la fixation d’une fiche secteur sur le

cordon d’alimentation de cet appareil doivent être

effectués par un personnel de service qualifié. En cas

de branchement sur une prise secteur, la fiche de

coupure peut provoquer une sérieuse décharge

électrique. Assurez-vous qu’elle est éliminée

correctement après sa dépose.

L’appareil doit être déconnecté en débranchant sa

fiche secteur au niveau de la prise murale si vous

prévoyez une période prolongée de non utilisation

(par exemple avant un départ en vacances).

D3-4-2-2-1a_A1_Fr

ATTENTION

L’interrupteur /I STANDBY/ON de cet appareil ne

coupe pas complètement celui-ci de sa prise secteur.

Comme le cordon d’alimentation fait office de

dispositif de déconnexion du secteur, il devra être

débranché au niveau de la prise secteur pour que

l’appareil soit complètement hors tension. Par

conséquent, veillez à installer l’appareil de telle

manière que son cordon d’alimentation puisse être

facilement débranché de la prise secteur en cas

d’accident. Pour éviter tout risque d’incendie, le

cordon d’alimentation sera débranché au niveau de

la prise secteur si vous prévoyez une période

prolongée de non utilisation (par exemple avant un

départ en vacances).

D3-4-2-2-2a*_A1_Fr

Milieu de fonctionnement

Température et humidité du milieu de fonctionnement :

De +5 °C à +35 °C (de +41 °F à +95 °F) ; Humidité

relative inférieure à 85 % (orifices de ventilation non

obstrués)

N’installez pas l’appareil dans un endroit mal ventilé ou

un lieu soumis à une forte humidité ou en plein soleil

(ou à une forte lumière artificielle).

D3-4-2-1-7c*_A1_Fr

Ce produit est destiné à une utilisation domestique

générale. Toute panne due à une utilisation autre qu'à

des fins privées (comme une utilisation à des fins

commerciales dans un restaurant, dans un autocar

ou sur un bateau) et qui nécessite une réparation

sera aux frais du client, même pendant la période de

garantie.

K041_A1_Fr

ATTENTION

Cet appareil est un produit laser de Classe 1, classé

selon l’article IEC 60825-1:2007 relatif à la Sécurité

des produits laser.

APPAREIL À LASER DE CLASSE 1

D58-5-2-2a_A2_Fr

Sommaire

01 Avant de commencer

Compatibilité en lecture des disques et du

format de gravure . . . . . . . . . . . . . . . . . . . . . . . . . 4

Contenu de l’emballage. . . . . . . . . . . . . . . . . . . . .4

Installation des piles dans la télécommande . . . . . 4

Utilisation de la télécommande. . . . . . . . . . . . . . . .4

02 Connexions

Connexions de sortie audio analogique . . . . . . . . .5

Connexions de sortie audio numérique . . . . . . . . . 5

Commande centralisée avec d’autres composants

Pioneer (PD-30 uniquement) . . . . . . . . . . . . . . . . . 5

Branchement . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

03 Commandes et écrans

Télécommande . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Panneau arrière. . . . . . . . . . . . . . . . . . . . . . . . . . .6

Panneau avant. . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Écran du panneau avant . . . . . . . . . . . . . . . . . . . . 7

04 Lecture

Lecture d’un disque. . . . . . . . . . . . . . . . . . . . . . . . 8

Réglage de la puissance sur la mise en veille . . . . .8

Lecture en avance/retour en arrière rapide . . . . . . .8

Fonction Ignorer (Skip) . . . . . . . . . . . . . . . . . . . . . .8

Recherche directe (désigne une piste

spécifique de lecture) . . . . . . . . . . . . . . . . . . . . . . .8

Lecture répétitive. . . . . . . . . . . . . . . . . . . . . . . . . . .8

Lecture au hasard . . . . . . . . . . . . . . . . . . . . . . . . . .8

Lecture programmée (lecture des pistes dans un

ordre prédéterminé) . . . . . . . . . . . . . . . . . . . . . . . .8

Visualisation des données du disque. . . . . . . . . . . .8

Lecture de l’iPod/iPhone/iPad

(PD-30 uniquement) . . . . . . . . . . . . . . . . . . . . . . . 9

Assurez-vous que les modèles iPod/iPhone/iPad

sont pris en charge . . . . . . . . . . . . . . . . . . . . . . . . .9

Lecture de votre iPod/iPhone/iPad . . . . . . . . . . . . .9

Lecture de fichiers enregistrés sur des dispositifs

de stockage USB . . . . . . . . . . . . . . . . . . . . . . . . . 10

05 Les fonctions avancées

Lecture avec son en haute fidélité . . . . . . . . . . . . 11

Sound Retriever. . . . . . . . . . . . . . . . . . . . . . . . . . .11

Pure Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Modification de la zone de lecture (couche) d’un

SACD/CD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Réglage de la luminosité de l’affichage . . . . . . . . 11

Auto Power Down (Mise hors tension automatique

réglant l’unité sur veille) . . . . . . . . . . . . . . . . . . . 11

Fonctions de lecture . . . . . . . . . . . . . . . . . . . . . . 11

06 Informations complémentaires

Disque pouvant être lu. . . . . . . . . . . . . . . . . . . . . 12

Formats de fichiers pouvant être lus . . . . . . . . . . 12

Précautions à prendre pour l’utilisation. . . . . . . . 13

Guide de dépannage . . . . . . . . . . . . . . . . . . . . . . 14

Spécifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

PD-30_PWSYXZT8-Fr.book Page 3 Wednesday, May 9, 2012 4:05 PM

Avant de commencer01

Chapitre 1:

Avant de commencer

Compatibilité en lecture des disques

et du format de gravure

Les disques pouvant être lus sur ce lecteur sont

répertoriés ci-dessous.

• SACD (Super Audio CD)*

(zone à deux canaux uniquement)

•CD

• Disque DSD

* “Super Audio CD” est une marque déposée.

Remarque

• Cette unité ne permet pas de lire des zones

multicanaux des disques SACD.

• Les bornes DIGITAL OUT de cette unité ne

produisent pas de son des disques SACD et DSD ni

des iPod/iPhone/iPad.

• Lorsqu’un disque est chargé, la mise sous tension

n’entraîne pas automatiquement le lancement de

la lecture. En conséquence, la lecture

chronométrée n’est pas possible même si l’unité

est connectée à une minuterie.

À propos de la lecture de disques DualDisc

Un disque DualDisc est un nouveau disque à deux faces,

l’une d’elle comportant du contenu DVD vidéo, audio,

etc. et l’autre comportant du contenu non-DVD tel que

des données audio numériques. La face audio non-DVD

du disque n’est pas conforme aux spécifications des CD

audio et il se peut donc que la lecture soit impossible.

Pour de plus amples informations sur les

caractéristiques des DualDisc, veuillez consulter le

fabricant ou le détaillant du disque.

Disques ne pouvant pas être lus

•DVD-Vidéo

• DVD-Audio

•CD-G

•CD Vidéo

• DTS CD

Il est possible que certains disques ne faisant pas partie

de la liste ci-dessus ne puissent pas être lus.

Contenu de l’emballage

Veuillez vous assurer que les accessoires suivants sont

livrés avec l’appareil.

• Télécommande x1

• Piles sèches AAA/IEC R03 x2

• Câble audio RCA (fiches rouges/blanches) x1

• Cordon d’alimentation

•Carte de garantie

• Mode d’emploi (ce document)

Remarque

• Les illustrations des Mode d’emploi peuvent avoir

été modifiées ou simplifiées dans le but de

clarification et en conséquence peuvent différer de

l’apparence actuelle du produit.

• Les illustrations utilisées ici représentent

principalement le modèle PD-30.

Installation des piles dans la

télécommande

1 Ouvrez le couvercle arrière.

PD-30

PD-10

2 Placez les piles neuves, en faisant

correspondre la polarité à celle du boîtier.

3 Fermez le couvercle arrière.

Les piles incluses avec l’unité ont été fournies pour

permettre de contrôler le fonctionnement du produit et

ne dureront pas longtemps. Nous recommandons

d’utiliser des piles alcalines qui ont une durée de vie

utile plus longue.

AVERTISSEMENT

• N’utilisez pas et ne rangez pas pas les piles sous la

lumière directe du soleil ou dans un endroit

excessivement chaud, comme une voiture ou à

proximité d’un appareil de chauffage. Les piles

risqueraient de fuir, de surchauffer, d’exploser ou

de s’enflammer. Leur durée de vie ou leurs

performances pourraient également être réduites.

Attention

Toute utilisation incorrecte des piles peut entraîner des

accidents, comme une fuite ou une explosion.

Respectez les précautions suivantes:

• Lorsque vous placez les piles, prenez soin de ne pas

endommager les ressorts des bornes des piles .

• Ne pas utiliser de piles autres que celles qui sont

indiquées. Ne pas utiliser non plus une pile neuve

avec une pile usée.

• Lorsque vous installez les piles dans la

télécommande, orientez les piles dans la bonne

direction en respectant la polarité ( et ).

• Ne pas chauffer, ni démonter, ni ne jeter les piles

dans le feu ou l’eau.

• La tension des piles peut différer l’une de l’autre et

cela même si leur type et forme sont identiques.

Utiliser ensemble uniquement des piles du même

type.

• Pour éviter que les piles ne fuient, enlever les piles

lorsque le produit n’est pas censé être utilisé

pendant une période prolongée (à savoir 1 mois ou

plus). Si les piles ont fuit, nettoyer soigneusement

l’intérieur du compartiment et placer ensuite les

piles. Si une pile fuit et que du liquide entre en

contact avec votre peau, nettoyer à grande quantité

d’eau.

• Lorsque vous jetez des piles usées, veuillez vous

conformer aux normes gouvernementales ou à la

réglementation des institutions publiques

environnementales en vigueur dans votre pays ou

région.

Utilisation de la télécommande

La télécommande a une portée d’environ 7 m à un angle

d’environ 30° par rapport au capteur.

Respectez les consignes suivantes lorsque vous utilisez

la télécommande:

• Aucun obstacle ne doit être présent entre la

télécommande et le capteur de l’appareil.

• Le fonctionnement de la télécommande peut être

perturbé si le capteur est soumis à un éclairage

trop puissant (rayons solaires ou lumière

fluorescente).

• L’utilisation simultanée de plusieurs

télécommandes peut brouiller leur

fonctionnement. Évitez d’utiliser d’autres

télécommandes à proximité de cet appareil.

• Remplacez la pile lorsque vous notez une baisse de

portée de la télécommande.

PD-30

PD-10

PD-30

PD-10

7 m

30 °

PD-30_PWSYXZT8-Fr.book Page 4 Wednesday, May 9, 2012 4:05 PM

Connexions 02

English

DeutschFrançais

Nederlands

Italiano Español Русский

Chapitre 2:

Connexions

Attention

• Avant d’effectuer ou de changer les connexions,

coupez le courant et déconnectez le cordon

d’alimentation de la prise CA.

• Connectez le cordon d’alimentation après avoir

effectué toutes les connexions entre les appareils.

Connexions de sortie audio analogique

Lorsque vous connectez la sortie audio analogique de

cette unité à la sortie audio analogique d’un

amplificateur, vous pouvez utiliser l’amplificateur pour

bénéficier de l’audio analogique de cette unité.

Connexions de sortie audio numérique

Vous pouvez, si souhaité, connecter la sortie audio

numérique de cette unité à un amplificateur AV ou un

appareil d’enregistrement numérique (enregistreur CD,

MD, etc.).

• Les bornes DIGITAL OUT de cette unité ne

produisent pas de son des disques SACD et DSD ni

des iPod/iPhone/iPad.

Important

Précaution à prendre lors de la manipulation des

câbles à fibre optique

• Prenez soin de ne pas plier les câbles à fibre

optique en angles aigus. Lorsque vous rangez les

câbles à fibre optique, enroulez-les en boucle de

15 cm de diamètre.

• Lors de la connexion des câbles à fibre optique,

alignez correctement les connecteurs et

introduisez-les complètement. Si l’orientation du

connecteur du câble est incorrecte et que vous

exercez une force excessive pour introduire le

connecteur, vous risquez de le déformer, ce qui

empêchera l’obturateur de se fermer lorsque le

câble est enlevé.

Remarque

• Pour la sortie audio numérique, les CD lus sur cette

unité doivent produire des signaux PCM linéaires

avec un taux d’échantillonnage allant jusqu’à

44,1 kHz et des bits quantitatives allant jusqu’à 16

bits (il peut s’avérer impossible de lire certains

disques sur le composant connecté et

l’environnement). Pour plus d’informations sur les

autres fichiers, voir page 12.

ANALOG

AUDIO INPUT

Amplificateur

Câble audio (inclus)

Panneau arrière du PD-30

DIGITAL IN

OPTICAL

DIGITAL IN

COAXIAL

Amplificateur AV ou

appareil d’enregistrement

numérique

Câble à fibre optique (en

vente dans le commerce)

Câble audio

numérique coaxial

(en vente dans le

commerce)

Panneau arrière du PD-30

Amplificateur AV ou

appareil d’enregistrement

numérique

Commande centralisée avec d’autres

composants Pioneer (PD-30 uniquement)

Cette unité et les autres composants Pioneer dotés de

prises CONTROL IN/OUT peuvent être contrôlés avec

une seule télécommande en la pointant vers le récepteur

de signaux sur l’amplificateur AV ou un autre

composant. Cette centralisation permet d’utiliser une

télécommande dont les composants ne sont pas munis

d’un télécapteur ou sont installés à des emplacements

inaccessibles par le télécapteur.

Remarque

• Pour établir la connexion, utilisez un cordon mini-

fiche mono en vente dans le commerce (sans

résistance).

• Lors de la connexion des prises CONTROL IN/OUT,

des cordons audio en vente dans le commerce

doivent être utilisés pour établir les connexions

analogiques. La connexion des prises CONTROL

IN/OUT ne suffit pas à à assurer un contrôle

adéquat du système.

• Lorsqu’un cordon de commande est connecté à la

prise CONTROL IN du PD-30, il est impossible de

contrôler l’unité en pointant la télécommande vers

le PD-30 (le télécapteur est automatiquement

désactivé).

Branchement

Important

• Si le cordon d’alimentation doit être déconnecté,

assurez-vous d’appuyer sur le bouton



STANDBY/ON situé le panneau avant de

l’unité de manière à ce que le PD-30 soit sur Arrêt

(OFF) ou le PD-10 en mode de veille avant de retirer

le cordon.

• Assurez-vous que l’indicateur [-OFF-] n’est pas

allumé sur l’écran du panneau avant de l’unité

principale avant de déconnecter le cordon

d’alimentation. Si le cordon d’alimentation est

déconnecté alors que l’indicateur [-OFF-] est

toujours allumé, l’unité peut revenir aux réglages

par défaut.

• Lorsque vous partez en voyage, ou lorsque vous

prévoyez de ne pas utiliser l’appareil pendant une

longue durée, débranchez systématiquement le

cordon d’alimentation de sa prise.

Attention

• Ne pas utiliser de cordon d’alimentation autre que

celui fourni avec cette unité.

• Ne pas utiliser le cordon d’alimentation fourni pour

un usage que celui qui est décrit ci-dessous.

Après avoir effectué toutes les connexions, branchez

l’unité dans une prise CA.

1 Branchez le cordon d’alimentation dans

la prise

AC IN

située sur le panneau arrière

de l’unité.

2 Branchez l’autre extrémité dans la prise

CA.

Vers d’autres composants

Pioneer munis d’une prise

CONTROL IN

Télécommande pour u

amplificateur AV, etc.

Pintez la télécommande

vers le récepteur de

signaux sur

l’amplificateur AV, etc.

Autres composants Pioneer

munis de prises CONTROL IN/

OUT

PD-30

Vers la prise CA

Cordon

d’alimentation

Panneau arrière du PD-30

PD-30_PWSYXZT8-Fr.book Page 5 Wednesday, May 9, 2012 4:05 PM

Commandes et écrans03

Chapitre 3:

Commandes et écrans

Télécommande

 STANDBY/ON

Permet de mettre l’amplificateur en mode veille et sous

tension.

2 Touches numérotées

Utilisez ces boutons pour spécifier la piste à lire. Utilisez

les boutons numérotés pour sélectionner la piste et

appuyez ensuite sur ENTER pour confirmer la sélection.

CLEAR

Appuyez pour effacer le contenu défini pour une lecture

programmée (page 8).

SETUP

Permet de régler la fonction de mise hors tension

automatique (page 11).

///

Utilisez ces boutons pour sélectionner des

éléments, changer les réglages et déplacer le

curseur.

ENTER

Permet d’inclure l’élément sélectionné ou de saisir

un réglage que vous avez changé.

iPod MENU

(PD-30 uniquement)

A utiliser avec un menu iPod/iPhone/iPad.



Appuyez pour revenir au début de la piste en cours

de lecture. Appuyez deux fois pour revenir au début

de la piste précédente.



Appuyez pour lancer la lecture. Au cours de la

lecture, faites une pause/annulez la pause de la

lecture.



Appuyez pendant la lecture pour avancer jusqu’à la

prochaine piste.



Appuyez pour revenir rapidement en arrière de la

piste en cours de lecture. Si vous appuyez à

nouveau sur le bouton pendant le retour en arrière

rapide, la vitesse de l’opération change en quatre

étapes.



Appuyez pour arrêter la lecture.



Appuyez pour avancer rapidement sur la piste en

cours de lecture. Si vous appuyez à nouveau sur le

bouton pendant l’avance rapide, la vitesse de

l’opération change en quatre étapes.

iPod/USB

(PD-30)

USB (PD-10)

Appuyez pour permuter l’unité à iPod ou USB

(page 9,10).

PD-10

PD-30

SACD/CD

Appuyez pour permuter l’unité à SACD/CD. Dans le cas

de disques SACD hybrides, si vous appuyez sur ce

bouton lors de l’arrêt de la lecture, la zone de lecture du

disque change (page 11).

REPEAT

Appuyez pour lancer une lecture répétitive (page 8).

RANDOM

Appuyez pour lancer une lecture au hasard

(page 8).

PROGRAM

Appuyez pour lancer une lecture programmée

(page 8).

11 PURE AUDIO

Appuyez sur ce bouton pour activer le mode Pure Audio.

Ce mode permet d’effectuer une lecture audio d’une

qualité supérieure respectant les sons originaux

(page 11).

 OPEN/CLOSE

Appuyez pour ouvrir et fermer le tiroir-disque (page 8).

ENTER

Permet d’inclure l’élément sélectionné ou de saisir un

réglage que vous avez changé.

DISPLAY

Appuyez pour afficher les diverses données sur le

disque, y compris le temps de lecture écoulé ainsi que le

temps restant (page 8).

DIMMER

Appuyez pour changer les niveaux de luminosité de

l’écran du panneau avant de l’unité principale et des

indicateurs (page 11).

S.RETRIEVER

Appuyez pour alterner entre les divers réglages de la

fonction Sound Retriever (page 11).

 AMPLIFIER

(PD-10 uniquement)

Appuyez pour permuter l’alimentation entre ON et

STANDBY sur l’amplificateur Pioneer AV.

VOLUME +/–

(PD-10 uniquement)

Appuyez sur ces boutons pour régler le volume du son

d’un amplificateur Pioneer AV.

MUTE

(PD-10 uniquement)

Appuyez pour mettre en sourdine le volume d’un

amplificateur Pioneer AV. Appuyez à nouveau sur ce

bouton pour annuler la fonction de mise en sourdine.

INPUT

(PD-10 uniquement)

Appuyez pour permuter l’entrée vers un amplificateur

Pioneer AV.

Panneau arrière

Pour de plus amples informations sur les connexions, voir page 5.

1 CONTROL IN/OUT prise (PD-30 uniquement)

DIGITAL OUT (COAXIAL)

borne

DIGITAL OUT (OPTICAL)

borne

ANALOG OUT

bornes

AC IN

prise

PD-30

DIGITAL IN

1 2 3 54

PD-30_PWSYXZT8-Fr.book Page 6 Wednesday, May 9, 2012 4:05 PM

La pagina sta caricando ...

Pioneer PD-10 Manuale utente

Marca: Pioneer

Modello: PD-10

Tipo: Manuale utente

Questo manuale è adatto anche per

Scarica il pdf

rapporto

in altre lingue

français: Pioneer PD-10 Manuel utilisateur
español: Pioneer PD-10 Manual de usuario
Deutsch: Pioneer PD-10 Benutzerhandbuch
Nederlands: Pioneer PD-10 Handleiding

Pioneer PD-10 Manuale utente

Questo manuale è adatto anche per

Pioneer PD-10 Manuale utente

in altre lingue

Documenti correlati