Hoover HNF6127PULSE-30 Manuale utente

Categoria
Lavatrici
Tipo
Manuale utente
Instruction Book
Washing Machine
English
Italiano
®
40003344Eng.qxd 03/06/2005 12:30 Page 1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Delivery information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Do’s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Don’ts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Unpacking the Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Choose a location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Electricity supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Water supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Connecting to the cold water supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Connection of the machine to the drain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Moving the machine into position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Adjusting the feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Testing the installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Washing advice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Loading your washing machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Sorting the laundry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
The Dispenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Detergent dosage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Dispensing instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
The Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Wash Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Automatic Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Programme Selector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Special Programmes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Daily Programmes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Programme Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
A Typical Wash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Selecting the wash programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Starting the wash cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Cleaning and Routine Maintenance. . . . . . . . . . . . . . . . . . . . 30
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Power Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
2
English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Italiano . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
40003344Eng.qxd 03/06/2005 12:30 Page 2
Introduction
Please read and follow these instructions
carefully and operate the machine accordingly.
This booklet provides important guidelines for
safe use, installation, maintenance and some
useful advice for best results when using your
machine.
Keep all documentation in a safe place for future
reference or for any future owners.
Delivery information
Please check that the following items are
delivered with the appliance:
Instruction manual
Guarantee card
Blanking plug
Inlet hose & hooked end support
(see Unpacking and Installation Instructions)
Base panel & x2 push clips
Energy Label
Do’s
All packaging materials used are
environmentally-friendly and recyclable.
Please help dispose of the packaging via
environmentally-friendly means. Your local
council will be able to give you details of
current means of disposal.
To ensure safety when disposing of an old
washing machine disconnect the mains plug
from the socket, cut the mains power cable
and destroy this together with the plug. To
prevent children shutting themselves in the
machine break the door hinges or the door
lock.
This machine is solely for domestic use,
i.e. to wash, rinse and spin dry household
textiles and garments.
3
Check that no
damage has
occurred to the
machine during
transit. If it has,
call for service
by GIAS.
40003344Eng.qxd 03/06/2005 12:30 Page 3
Don’ts
Do not touch the appliance when hands or
feet are damp or wet.
Do not lean on the door when loading the
machine or use the door to lift or move the
machine.
Do not use adapters, multiple connectors
and/or extensions.
Do not allow children to play with the
machine or its controls.
Do not try to open the door when water is
visible in the drum or the door locked
indicator (Blocco Porta) is on.
European directive
2002/96/EC
This appliance is marked according to the
European directive 2002/96/EC on Waste Electrical
and Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly,
you will help prevent potential negative
consequences for the environment and human
health, which could otherwise be caused by
inappropriate waste handling of this product.
The symbol on the product indicates that this
product may not be treated as household waste.
Instead it shall be handed over to the applicable
collection point for the recycling of electrical and
electronic equipment
Disposal must be carried out in accordance with
local environmental regulations for waste disposal.
For more detailed information about treatment,
recovery and recycling of this product, please
contact your local city office, your household
waste disposal service or the shop where you
purchased the product.
4
Failure to
comply with
the above can
compromise the
safety of the
appliance. You
may be charged
for a service call
if a problem
with your
machine is
caused by
misuse.
If the appliance
is not running
properly or
breaks down,
switch it off,
disconnect the
plug from the
socket, turn off
the water
supply and do
not tamper
with the
appliance.
Consult GIAS
Service for
possible repair.
40003344Eng.qxd 03/06/2005 12:30 Page 4
Unpacking the product
Remove the machine from its packaging close to
the final location of the machine.
1. Cut carefully around the base of the
packaging.
2. Lay the machine on its back and remove the
base and the two polystyrene spacers on
each side of the machine. We recommend
that a second person assist in the lifting and
manoeuvring of the machine.
3. Return the machine to the upright position,
remove the remainder of the packaging and
the central screw in the transit bar.
4. Remove the four retaining screws in the
transit bar and pull out the transit bracket.
5
Dispose of the packaging safely.
Make sure it is out of the reach
of children, it is a potential
source of danger.
40003344Eng.qxd 03/06/2005 12:30 Page 5
5. Take the base panel provided and fit the
two self adhesive strips by removing the
backing paper on one side and locating the
strips on each side of the base panel.
6. Tilt the machine forward and locate the
base panel under the front of the machine.
Remove the remaining backing paper from
the self-adhesive strips and offer up the
base panel to the bottom of the cabinet.
7. Take the two plastic fixing clips and fix the
base panel to the base of the machine.
Bring the machine back to the upright
position.
6
We recommend you keep the transit bracket and
screws to protect the machine for future transit.
The manufacturers will not be responsible for any
damage to the machine caused by not following the
instructions relating to releasing the transit protection.
The user is responsible for all installation costs.
40003344Eng.qxd 03/06/2005 12:30 Page 6
8. Cover the central hole in the rear of the
machine with the cap enclosed in the
instruction bag.
Choose a location
After the machine has been installed, ensure
that the mains plug and water supply valves
are easily accessible.
Make sure there is enough space for the
machine. Select a space at least 600mm wide
and 850mm high. Also leave enough space
to open the door fully so you can load and
unload it easily.
Keep the area underneath and around the
machine free of combustible materials such
as lint, paper, rags, chemicals etc.
7
Installation
Do not plug the
machine in and
switch it on at
the mains until
the installation
is completed.
40003344Eng.qxd 03/06/2005 12:30 Page 7
Electricity supply
Washing machines are supplied to operate at a
voltage of 230V, 50 Hz single phase. Check that
the supply circuit is rated to at least 10A.
Electricity can be extremely dangerous.
This washing machine must be earthed.
The socket outlet and the plug on the appliance
must be of the same type.
Do not use multiple adapters and/or extension
leads.
The wires in the mains lead are coloured in
accordance with the following codes:
Blue NEUTRAL
Brown LIVE
Green and Yellow EARTH
CE Appliance complies with European Directive
89/336/EEC, 73/23/EEC and subsequent
amendments.
Water supply
The cold water pressure should be between
0.05-0.8 Mpa.
Do not connect the machine to a single
outlet instantaneous water heater.
The water supply tap should be accessible
when the machine is installed.
Before connecting the fill hose, check that
the water is running from the water supply
tap to be used.
8
You may be
charged for a
service call if a
problem with
your machine is
caused by
incorrect
installation.
If the mains
cord on this
appliance is
damaged, it
must be
replaced by a
special cord
which is ONLY
obtainable from
the GIAS spares
service. It must
be installed by
a competent
person.
40003344Eng.qxd 03/06/2005 12:30 Page 8
Connecting to the cold
water supply
This machine has an inlet hose with a 19mm
(3/4") threaded ferrule fitted to the end, to
attach between the threaded connector on the
appliance and the water supply.
Only use the new hose supplied to connect the
machine and ensure that the sealing washers are
in place inside the hose connectors.
Do not re-use old hoses which are attached to
existing installations.
Do not over-tighten the connections. Hand tight
is sufficient.
Do not trap or kink the hose.
1. Connect the elbow end of the hose provided
to the threaded inlet on the back of the
machine.
Grey pipe to the white threaded inlet on
the machine.
2. Hand tighten the connector.
3. Connect the straight ends of the pipes to
the water supply; ensure that there are no
kinks.
4. Turn on the water supply and check for
leaks. If there is a leak, turn off the water
supply, disconnect the hose and check the
sealing washers are in place. Refit the hose
and turn on the water supply.
9
40003344Eng.qxd 03/06/2005 12:30 Page 9
Connection of the machine to the
drain
This machine must be connected in accordance with the water supply
regulations. Water byelaws prohibit connection to a surface water drain.
Decide which plumbing option suits you best then follow the instructions
below.
Option 1
Waste pipe connection (waste trap)
Fit the hooked end support to the outlet pipe. Position at least 800mm off the
floor.
After removing the blanking plug or cutting the membrane from the waste
system securely fix the outlet pipe to the drainage system, using a hose clip.
Secure the hooked end support up to at least 800mm to avoid water being
drawn back into the machine.
10
All machines are tested with water prior to leaving the
factory so a small amount of water may remain in the
drum and drain hose.
Flooding could occur if any part of the installation is
not completed correctly.
800 mm
hose clip
hooked end support
sink
flexible
discharge hose
trap with hose
adaptor
40003344Eng.qxd 03/06/2005 12:30 Page 10
Option 2
Into a standpipe
Ensure that the standpipe is not located near
an electrical socket.
Fit the hooked end support to the outlet pipe.
Install the hose into the standpipe ensuring
that the pipe is at least 500mm from the floor.
Insert the outlet pipe approximately 100mm
into the standpipe.
Moving the machine
into position
Your machine is heavy so care must be taken
when moving it. We recommend that two people
move the machine to avoid strain and possible
injury.
Take care not to damage flooring when
moving the machine.
When moving the machine to its final
position take care not to kink or damage
the hose at the back of the machine.
Adjusting the feet
Once the machine is in place the feet should be
adjusted to ensure that the machine is level. If
the machine is not level it may become noisy or
move.
Adjust the feet on the front corners of the
machine until the machine is firm and level.
When the machine is firm and level, tighten the
locking nuts on the two feet.
11
Do not drag or
lift the machine
by its door.
100 mm
500 mm
min
40003344Eng.qxd 03/06/2005 12:30 Page 11
Refer to the programme guide for details of how
to select programmes.
1. Turn on the water supply and check for
leaks from the fill hose.
2. Switch on the electricity supply.
3. Select the spin programme and then
press the Avvio/Pausa button to start the
machine. Allow the programme to continue
for one minute and then cancel the
programme by returning the selector to the
OFF position. This will remove any water
remaining in the machine from factory
testing.
4. To check for cold water filling to the
machine:
Select the rinse programme and press
the Avvio Pausa button to start the machine.
Allow the tumble action to continue until
the water has pumped out. Check that the
drain outlet is not leaking or overflowing.
5. Switch off the machine at the end of the
cycle by turning the programme knob to the
OFF position.
6. Select the spin programme and press
the Avvio Pausa button to switch the
machine on. If the machine takes longer
than one minute to empty check the drain
hose for kinks.
Installation testing is now
complete.
Now you have successfully installed the machine
we advise that you run the machine to ensure the
drum is thoroughly clean after testing and
storage. Select Cotone Resistente and run the
machine for a complete cycle using only wash
detergent and water.
12
Testing the installation
This
programme
will take
approximately
2 hours to
complete.
40003344Eng.qxd 03/06/2005 12:30 Page 12
The following tips are designed to assist in
getting the best results from your machine whilst
utilising it in the most environmentally-friendly
and economical way. It is also important to
understand the items to avoid in your laundry, to
ensure the continued safe and reliable operation
of your machine.
Loading your washing
machine
To make further reductions of energy, water and
detergent consumption, we recommend that you
put a full load into your machine. Energy savings
of up to 50% can be achieved by washing one full
load compared to two half loads.
Do not overload the machine as this will reduce
the quality of the wash and may cause damage
to the machine and your laundry.
When is prewashing really
needed?
Only with particularly dirty loads! Energy savings
of 5 to 15% are made by not selecting the
prewash option for less dirty laundry. Pre-treat
awkward stains with a washable stain remover.
Which wash temperature should
you choose?
Using stain removers before machine washing
reduces the need to wash at temperatures over
60°C.
Using a 40°C wash temperature can make energy
savings of up to 50%.
Heavily soiled laundry
To ensure the best performance when washing a
particularly dirty load, we recommend that you
reduce the amount of items to be put into the
machine. Allowing more space in the drum the
13
Washing advice
40003344Eng.qxd 03/06/2005 12:30 Page 13
items can circulate more freely and will wash
cleaner.
Sorting the laundry
Items to avoid
We recommend that you do not wash underwired
bras in the machine. Should the wires become
detached it could cause damage to your clothes
and the machine. If the washcare label states that
the bra is machine washable then we advise
placing it in a wash bag.
Recommendations
Always follow the wash care labelling on the
garments.
Fasten zips, tie strings and close press studs to
prevent tangling. Ensure that pockets are
emptied of loose change and other small items.
Check that there are no metal objects in the
laundry as these may damage the laundry and
the machine.
Place small items in a wash bag.
14
Do not use the
machine to
wash items that
do not have a
wash label.
Do not wash
items
previously
treated with
solvents.
40003344Eng.qxd 03/06/2005 12:30 Page 14
Detergent dosage
Only use detergents which are suitable for use in a washing machine. You will
obtain the best results from your wash with the minimum use of chemical
products, and the best care for your laundry if you take into consideration the
degree of soiling as well as the type of detergent to choose.
The amount of detergent to use depends on:
Water hardness.
Depending on the hardness of the water and the type of detergent used,
it is possible to reduce the amount of detergent.
The softer the water supply, the less detergent is required.
The degree of soiling.
It is possible to reduce the amount of detergent used depending on the
degree of soiling.
Use less detergent for less soiled items.
Amount of laundry.
It is possible to reduce the amount of detergent when washing only a
small amount of laundry.
For smaller loads use less detergent.
The dosages shown on the packaging of detergents for washing delicates
often already refer to a reduced wash size. Always follow the dosage
instructions on the detergent packaging.
15
The Dispenser
DO NOT exceed the maximum detergent dosage
COMPARTMENT I
Prewash detergent
Maximum dosage
100ml of powder
COMPARTMENT II
Mainwash detergent
Maximum dosage
200ml of powder
COMPARTMENT
Fabric Conditioner
Maximum dosage 200ml
40003344Eng.qxd 03/06/2005 12:31 Page 15
Dispensing instructions
The detergent drawer is split into 3
compartments:
the left-hand compartment, labelled "II", is
for detergent used during the main wash.
the centre compartment, labelled is for
special additives such as fabric softeners,
fragrances, starch, brighteners etc.
the right-hand compartment, labelled "I", is
for detergent used during Prewash.
Dispensing in the drum
Liquid detergents and some tablets are dispensed
via the machine drum using the recommended
dispensing device which is placed upright on top
of the washload towards the back of the drum.
Some tablets are designed to be placed in the
dispenser drawer, check the detergent pack for
details.
16
Do not put any
items into the
drawer other
than detergents
that are
designed to be
dispensed from
the drawer as
they may cause
blockage or
damage.
40003344Eng.qxd 03/06/2005 12:31 Page 16
Turning the machine on
The machine is turned on by selecting a programme via the programme
selector. This status will be indicated by the STOP indicator light flashing, this
light will continue to flash until the machine has started or the machine is
returned to the OFF position.
Start/Pause (Avvio/Pausa)
Start (Avvio)
After selecting the programme and the required options press the Avvio Pausa
button once to start the machine. The STOP light will stop flashing and START
light will illuminate and there will be a short time delay to the start of the
programme while the machine sets the wash parameters for the selected
programme and options. If the duration of the programme you have selected
is shorter than 60 minutes, then the time remaining indicator will illuminate
accordingly. The Blocco Porta indicator light will also illuminate a few seconds
after pressing the Avvio Pausa button.
17
The Control Panel
The programme selector must be returned to the OFF
position to reset the controls between each wash cycle.
CHRONOVISION
Display
Door Locked Indicator
(Blocco Porta)
Start/Pause
(Avvio
Pausa)
Delay Start
(Partenza
Differita)
Pre Wash
(Pre Lavaggio)
Day & Night
(Buona
Notte)
Special
Care (Stop
Allergia)
Spin Speed
Selector
(Giri
Centrifuga)
Temperature
Selector
(Temperatura
Lavaggio)
Programme
Selector
40003344Eng.qxd 03/06/2005 12:31 Page 17
Pause (Pausa)
The programme may be paused at any time
during the wash cycle by holding down the Avvio
Pausa button for about two seconds. When the
machine is in the paused mode, the time
remaining for the programme in the
CHRONOVISION indicator and option buttons will
flash. The Blocco Porta indicator light will remain
illuminated for approximately 2 minutes. The
door can be opened when this indicator goes out.
To restart the programme, press the Avvio Pausa
button once again.
Cancelling and changing the
programme
To cancel the programme the programme selector
should be rotated to the OFF position.
Select a new programme and start as detailed
above.
Door Locked indicator
(Blocco Porta)
The Blocco Porta indicator light is illuminated
when the door is fully closed and the machine is
ON.
When Avvio Pausa is pressed on the machine with
the door closed the indicator will flash
momentarily and then illuminate. If the door is
not closed the indicator will continue to flash.
A special safety device prevents the door from
being opened immediately after the end of the
cycle. Wait for 2 minutes after the wash cycle has
finished and the Blocco Porta light has gone out
before opening the door. As a safety measure,
check that there is no water evident in the drum.
At the end of the cycle turn the programme
selector to OFF.
If the programme is paused, the door locked
indicator will go out after 2 minutes and the door
can be opened. Check there is no water evident
in the drum before opening the door.
18
When starting a
subsequent
wash cycle the
programme
selector must
be returned to
OFF prior to the
next
programme
being selected
and started.
40003344Eng.qxd 03/06/2005 12:31 Page 18
CHRONOVISION
In order to better manage your time, this washing
machine features an indicator light system that
keeps you constantly informed on the remaining
cycle time and the status of the start delay
function.
When a drying time is selected the
CHRONOVISION display will display the time
remaining on the washing programme when the
washing is taking place and the time remaining in
the drying phase when drying is taking place.
19
START
60'
30'
15'
STOP
Remaining time above
60 minutes
Remaining time less
than 60 minutes
Remaining time less
than 30 minutes
Remaining time less
than 15 minutes
End of the programme
3h
6h
9h
3 hours or less remaining
before the programme
commences
6 hours or less remaining
before the programme
commences
9 hours or less remaining
before the programme
commences
CHRONOVISION DISPLAY
WASH PROGRESS
START DELAY
40003344Eng.qxd 03/06/2005 12:31 Page 19
Prewash (Pre Lavaggio)
This option is available on the cottons and
synthetics programmes. Prewash is automatic on
the Sports programme. This option is particularly
useful for heavily soiled loads and can be used
before selecting the main wash programme.
Detergent for this programme should be added
to the first compartment of the soap drawer
labelled "I" (Please refer to Detergent Drawer
section of manual). We recommend you only use
20% of the main wash detergent quantity.
Delay Start (Partenza Differita)
This option is available to delay the start of the
wash cycle by up to 9 hours. The selection of the
time is completed by pressing the Partenza
Differita button, the CHRONOVISION display will
indicate the time selected. When the correct
delay is selected press the Avvio Pausa button to
start the cycle.
Special Care (Stop Allergia)
By pressing this button you can activate a special
new wash cycle in the Cottons and Mixed Fabrics
programs, thanks to the new Optima wash
system. This option treats with care the fibres of
garments and the delicate skin of those who wear
them.
The load is washed in a much larger quantity of
water and this, together with the new combined
action of the drum rotation cycles, where water is
filled and emptied, will give you garments which
have been cleaned and rinsed to perfection. The
amount of water in the wash is increased so that
the detergent dissolves perfectly, ensuring an
efficient cleaning action. The amount of water is
also increased during the rinse procedure so as to
remove all traces of detergent from the fibres.
This function has been specifically designed for
people with delicate and sensitive skin, for whom
even a very small amount of detergent can cause
irritation or allergy. You are advised to also use
20
Wash Options
The options
should be
selected
BEFORE
pressing the
Avvio Pausa
button
40003344Eng.qxd 03/06/2005 12:31 Page 20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72

Hoover HNF6127PULSE-30 Manuale utente

Categoria
Lavatrici
Tipo
Manuale utente