Behringer ULTRA METAL UM100 Manuale utente
- Tipo
- Manuale utente
ULTRA METAL UM100
Thank you for showing your confidence in us by purchasing the BEHRINGER ULTRA
METAL UM100. This high-quality effects pedal comes with a dual-gain circuitry that
enables you to produce super thick, tube-like distortion plus endless sustain. Thanks to
its high-performance features you will achieve the most extreme and sought-after hard
rock or heavy metal distortion sounds.
1. CONTROLS
Top view
The DIST(ortion) control adjusts the amount of distortion effect.
The HIGH control allows you to boost/cut the high-frequency range.
The LOW control allows you to boost/cut the low-frequency range.
+ Please keep in mind that extreme distortion and EQ settings will increase
noise and may induce oscillation.
The two MID FREQ(uency) controls allow to boost/cut a defined mid-frequency
range. The upper control is used to increase or lower the mid range, the control below
adjusts the middle frequency of the mid range that is affected (200 Hz to 5 kHz).
The LEVEL control adjusts the output level.
The ON/BATT LED illuminates when the effect is activated. It also serves as a
battery level indicator.
Use the footswitch to activate/deactivate the effect.
Use this 1/4" TS IN connector to plug in the instrument cable.
The 1/4" TS OUT connector sends the signal to your amp.
Use the DC IN connectionto plug in a 9 V power supply (not included).
The BATTERY COMPARTMENT is located underneath the pedal cover. To install or
replace the 9 V battery, press the hinges with a ballpen and remove the pedal cover. Be
careful not to scratch the unit.
ULTRA METAL UM100
+ The UM100 has no on/off switch. As soon as you insert the jack into the IN
connector, the UM100 begins running. When not using the UM100, remove
the jack from the IN connector. This extends the life of the battery.
The SERIAL NUMBER is located at the bottom.
2. WARRANTY
For our current warranty terms, please refer to our website at http://www.behringer.com.
3. SPECIFICATIONS
In
Connector 1/4" TS
Impedance 500 kW
Out
Connector 1/4" TS
Impedance 1 kW
Power supply 9 V, 100 mA DC regulated
PSU-SB-CN BEHRINGER 220 VAC adaptor China
PSU-SB-EU BEHRINGER 230 VAC adaptor Europe
PSU-SB-JP BEHRINGER 100 VAC adaptor Japan
PSU-SB-SAA BEHRINGER 240 VAC adaptor Australia
PSU-SB-UK BEHRINGER 240 VAC adaptor UK
PSU-SB-UL BEHRINGER 115 VAC adaptor USA
Power connector 2 mm DC jack, negative center
Battery 9 V type 6LR61
Power consumption 30 mA
Dimensions (H x W x D) approx. 54 mm (2 1/8") x 70 mm (2 3/4") x 123 mm (4 4/5")
Weight approx. 0.33 kg (0.73 lbs)
BEHRINGER is constantly striving to maintain the highest professional standards. As a result of these efforts, modifications
may be made from time to time to existing products without prior notice. Specifications and appearance may therefore differ from
those listed or shown.
4. SAFETY INSTRUCTIONS
Do not use near water, or install near heat sources. Use only authorized attachments/accessories. Do not service product yourself.
Contact our qualified servicing personnel for servicing or repairs, especially when power supply cord or plug is damaged.
No utilizar cerca de agua o instalar cerca de fuentes de calor. Utilice sólo accesorios y aditamentos autorizados. No intenté reparar
el producto usted mismo. Contacte a nuestro personal técnico cualificado para servicio y reparaciones, especialmente cuando la
fuente o el cable de alimentación estén dañados.
Technical specifications and appearance subject to change without notice. The information contained herein is correct at the time
of printing. The names of companies, institutions or publications pictured or mentioned and their respective logos are registered
trademarks of their respective owners. Their use neither constitutes a claim of the trademarks by BEHRINGER
®
nor affiliation of the
trademark owners with BEHRINGER
®
. BEHRINGER
®
accepts no liability for any loss which may be suffered by any person who relies
either wholly or in part upon any description, photograph or statement contained herein. Colours and specification may vary slightly
from product. Products are sold through our authorised dealers only. Distributors and dealers are not agents of BEHRINGER
®
and have
absolutely no authority to bind BEHRINGER
®
by any express or implied undertaking or representation. No part of this manual may be
reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording of any kind,
for any purpose, without the express written permission of BEHRINGER Spezielle Studiotechnik GmbH. BEHRINGER
®
is a registered
trademark. ALL RIGHTS RESERVED. © 2005 BEHRINGER Spezielle Studiotechnik GmbH, Hanns-Martin-Schleyer-Str. 36-38, 47877
Willich-Münchheide II, Germany. Tel. +49 2154 9206 0, Fax +49 2154 9206 4903
Die deutsche Anleitung ist erhältlich @ www.behringer.com
Manuel francophone en téléchargement sur www.behringer.com
Manual en español disponible en www.behringer.com
Manuali italiani disponibili @ www.behringer.com
Nederlandse handleiding beschikbaar @ www.behringer.com
Suomenkielinen käyttöohje saatavilla osoitteesta www.behringer.com
Svensk manual finns tillgänglig på www.behringer.com
Dansk vejledning findes på @ www.behringer.com
Manual português disponível @ www.behringer.com
Åëëçíéêü åã÷åéñßäéï õðÜñ÷åé äéáèÝóéìï óôç äéåýèõíóç www.behringer.com
-
1
-
2
Behringer ULTRA METAL UM100 Manuale utente
- Tipo
- Manuale utente
in altre lingue
Documenti correlati
-
Behringer OVERDRIVE DISTORTION OD100 Manuale utente
-
-
-
-
-
-
-
-
-
Vintage Tube Overdrive TO800 Manuale utente