Hitachi HDC-1098EP Manuale del proprietario

EN-1

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may

cause undesired operation.

Note:

This equipment has been tested and found to comply with the limits for Class B digital

devices, pursuant to Part 15 of the FCC rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation.This

equipment generates uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

Use of shielded cable is required to comply with Class B limits in Subpart B of Part 15

of the FCC rules.

Do not make any changes or modifications to the equipment unless otherwise

specified in the manual. If such changes or modifications should be made, you could

be required to stop operation of the equipment.

Notice

If static electricity or electromagnetism causes data transfer to discontinue midway

(fail), restart the application or disconnect and connect the communication cable

(USB, etc.) again.

EN-2

READ THIS FIRST

Trademark Information



Microsoft

®

and Windows

®

are U.S. registered trademarks of Microsoft Corporation.

 Pentium

®

is a registered trademark of Intel Corporation.

 Macintosh is a trademark of Apple Inc.

 SD™ is a trademark.

 SDHC™ is a trademark.

 Other names and products may be trademarks or registered trademarks of their

respective owners.

Product Information

 Product design and specifications are subject to change without notice. This

includes primary product specifications, software, software drivers, and user’s

manual. This User Manual is a general reference guide for the product.

 The product and accessories that come with your camera may be different from

those described in this manual. This is due to the fact that different retailers often

specify slightly different product inclusions and accessories to suit their market

requirements, customer demographics, and geographical preferences. Products

very often vary between retailers especially with accessories such as batteries,

chargers, AC adapters, memory cards, cables, pouches, and language support.

Occasionally a retailer will specify a unique product colour, appearance, and

internal memory capacity. Contact your dealer for precise product definition and

included accessories.

 The illustrations in this manual are for the purpose of explanation and may differ

from the actual design of your camera.

 The manufacturer assumes no liability for any errors or discrepancies in this user

manual.

EN-3

SAFETY INSTRUCTIONS

Read and understand all Warnings and Cautions before using this product.

Warnings

If foreign objects or water have entered the camera, turn the power off

and remove the battery.

Continued use might cause fire or electric shock. Consult the store of

purchase.

If the camera has fallen or its case has been damaged, turn the power

off and remove the battery.

Continued use might cause fire or electric shock. Consult the store of

purchase.

Do not disassemble, change or repair the camera.

This might cause fire or electric shock. For repair or internal inspection, ask

the store of purchase.

Use the supplied AC adapter only with the indicated power supply

voltage.

Use with any other power supply voltage might cause fire or electric shock.

Do not use the camera in areas near water.

This might cause fire or electric shock. Take special care during rain, snow,

on the beach, or near the shore.

Do not place the camera on inclined or unstable surfaces.

This might cause the camera to fall or tilt over, causing damage.

Keep the battery out of the reach of children.

Swallowing the battery might cause poisoning. If the battery is accidentally

swallowed, immediately consult a physician.

Do not use the camera while you are walking, driving or riding a

motorcycle.

This might cause you to fall over or result in traffic accident.

Please use battery with complete external seals.

Do not use battery from which the seals have been damaged or removed.

This may cause leakage, explosion, or injury.

EN-4

Cautions

Insert the battery paying careful attention to the polarity (+ or –) of the

terminals.

Inserting the battery with its polarities inverted might cause fire and injury, or

damage to the surrounding areas due to the battery rupturing or leaking.

Do not fire the flash close to anyone’s eyes.

This might cause damage to the person’s eyesight.

Do not subject the LCD monitor to impact.

This might damage the glass on the screen or cause the internal fluid to

leak. If the internal fluid enters your eyes or comes into contact with your

body or clothes, rinse with fresh water. If the internal fluid has entered your

eyes, consult a physician to receive treatment.

A camera is a precision instrument. Do not drop it, strike it or use

excessive force when handling the camera.

This might cause damage to the camera.

Do not use the camera in humid, steamy, smoky, or dusty places.

This might cause fire or electric shock.

Do not remove the battery immediately after long period of continuous

use.

The battery becomes hot during use. Touching a hot battery might cause

burns.

Do not wrap the camera or place it in cloth or blankets.

This might cause heat to build up and deform the case, resulting in fire. Use

the camera in a well-ventilated place.

Do not leave the camera in places where the temperature may rise

significantly, such as inside a car.

This might adversely affect the case or the parts inside, resulting in fire.

Before you move the camera, disconnect cords and cables.

Failure to do this might damage cords and cables, resulting in fire and

electric shock.

EN-5

Notes on Battery Usage

When you use the battery, carefully read and strictly observe the Safety Instructions

and the notes described below:

 Use only the specified battery (3.7V).

 Avoid extremely cold environments as low temperatures can shorten the battery

life and reduce camera performance.

 When you are using a new rechargeable battery or a rechargeable battery that has

not been used for an extended period of time (the battery that passed the expiry

date is an exception), it may affect the number of images that can be captured.

Therefore, to maximize its performance and lifetime, we recommend that you fully

charge the battery and discharge it for at least one complete cycle before use.

 The battery may feel warm after a long period of continuous use of the camera or

the flash. This is normal and not a malfunction.

 The camera may feel warm after a long period of continuous use. This is normal

and not a malfunction.

 If the battery is not to be used for a long period of time, remove it from the camera

to prevent leakage or corrosion and store it after no battery power is left. Stored for

a long time in a fully charged condition, its performance may be impaired.

 Always keep the battery terminals clean.

 There is a risk of explosion if the battery is replaced by an incorrect type.

 Dispose of used battery according to the recycle instructions.

 Charge the rechargeable!battery fully before using for the first time.

 To prevent short-circuiting or fire, keep the battery away from other metal objects

when carrying or storing.

This symbol mark [crossed-out wheeled bin] indicates separate col-

lection of waste batteries in the EU countries. The batteries provided

with this product shall not be treated as household waste. Please use

the return and collection systems available in your country for the

disposal of the waste batteries.

If a chemical symbol is printed beneath the symbol mark, this

chemical symbol means that the batteries contains a heavy metal at

a certain concentration. It is indicated as follows:

Hg: mercury, Cd: cadmium, Pb: lead.

CONTENTS

EN-6

7 INTRODUCTION

7 Overview

7 Package Contents

8 GETTING TO KNOW YOUR

CAMERA

8 Front View

9Rear View

10 LCD Monitor Display

12 GETTING STARTED

12 Preparation

13 Charging the Battery

14 Initial Settings

16 CAPTURE MODE

16 Capturing Images

17 Taking Images When the Smile

Feature Is On

18 Recording Shots into Multiple

Image Layout

19 Setting the Scene Mode

20 Setting the Panorama Mode

21 VIDEO MODE

21 Recording Video Clips

21 Playing Back Video Clips

22 PLAYBACK MODE

22 Playing Back Still Images

23 Playback Display

23 Removing Red-eye

24 Attaching Voice Memos

25 DPOF Settings

26 Protecting Images

27 Erasing Images

28 MENU OPTIONS

28 Capture Menu

31 Video Menu

32 Playback Menu

33 Setup Menu

35 TRANSFERRING FILES TO

YOUR COMPUTER

35 Downloading Your Files

36 USING THE CAMERA AS A PC

CAMERA

37 EDITING SOFTWARE

INSTALLATION

38 SPECIFICATIONS

39 APPENDIX

39 Possible Number of Shots

40 Troubleshooting

41 Connecting to a PictBridge

Compliant Printer

EN-7

INTRODUCTION

Overview

Congratulations on your purchase of the new digital camera.

Capturing high-quality digital images is fast and easy with this state-of-the-art smart

camera. Equipped with a 10.0-megapixel CCD, this camera is capable of capturing

images with a resolution of up to 3648 x 2736 pixels.

Package Contents

Carefully unpack your camera and ensure that you have the following items:

Common Product Components:

 Digital camera

 User’s manual

 Software CD-ROM

 USB cable

 AV cable

 Camera strap

 Camera pouch

 Rechargeable lithium-ion battery

 Battery charger

 AC adapter for battery charger

Common (Optional) Accessories:

 SD/SDHC memory card

 Accessories and components may vary by retailer.

EN-8

GETTING TO KNOW YOUR CAMERA

Front View

1 2 3 5

8

7

6

4

1. MODE button

2. Self-timer LED

3. ON/OFF power button

4. Status LED

5. Flash

6. Lens

7. Microphone

8. Zoom lever

EN-9

Rear View

Item

Function

8

Capture Mode

6

Video Mode 7 Playback Mode

1. Shutter button Record button Voice memo rec.

2. Playback Playback Playback

3. Menu Menu Menu

4. Focus

auto>Z>O>Q

Focus

auto>O>Q

next 10th image

5. Flash

Auto>a>d>c>`>_

--

Next image

6. Self-timer

Off>f>g>h

Self-timer

Off>f>g

previous 10th image

7. Compensation

s>P

--

Previous image

8. Set Set Set

9. -- -- Delete

1

2

3

4

5

6

7

8

9

d

e

f

EN-10

LCD Monitor Display

Capture mode

P

m

2008 / 01 / 01 00 : 00

2008/01/01 00:00

00001

+ 0.3

x4.0

1 2

3

1011

12

13

4

5

6

7

8

9

14

15

16

17

18

q

1. Zoom status

2. Flash mode

[Blank]Auto Flash

[a] Forced Flash

[d] Flash Off

[c] Red-eye Reduction

[`] Slow Sync

[_] Pre-flash

3. Battery condition

[l] Full battery power

[o] Medium battery

power

[n] Low battery power

[m] No battery power

4. Storage media

[r]

Internal memory

(no card)

[q] SD/SDHC

memory card

5. [ ] Histogram

6. Main focus area

7. Image quality

[y] Fine

[x] Standard

[w] Economy

8. Image size resolution

[p] 3648 x 2736

[l] 2816 x 2112

[i] 2272 x 1704

[f] 1600 x 1200

[x] 640 x 480

9. Available number of

shots

10. ISO

[Blank] Auto

[:] ISO 64

[5] ISO 100

[7] ISO 200

[9] ISO 400

[0] ISO 800

[;] ISO 1600

11. Self-timer icon

[f] 2 sec.

[g] 10 sec.

[h] 10+2 sec.

12. Date and time

13. [s]Exposure

compensation

[P] Backlight correction

(Adjust exposure value

with the e / fbuttons)

14. Capture mode icon

[Blank] Single

[T] Continuous

[U] AEB

[

]

- Album Shot

[/] Burst

[.] Cont.flash

[+] Pre-Shot

[

]

, Coupl. Shot

15. Slow shutter warning

16. White balance

[Blank] Auto

[$] Incand.

[&] Fluoresc.1

[*] Fluoresc.2

[%] Daylight

[#] Cloudy

[(] Manual WB

17. Focus setting

[Blank] Auto focus

[Z] Face detection

[O] Macro

[Q] Infinity

18. Scene mode

[W] Smile Shot

[t] Anti-shake

[T] Panorama

[Q] Portrait Man

[R] Portrait Lady

[N] Landscape

[F] Sports

[B] Night Portrait

[C] Night Scene

[G] Candlelight

[H] Fireworks

[M] Text

[K] Sunset

[I] Sunrise

[E] Splash Water

[J] Flow Water

[X] Snow

[S] Beach

[D] Pets

[L] Nautral Green

[N] User Setting

EN-11

Video mode [B]

1. Zoom status

2. Flash mode

3. Battery condition

4. Storage media

5. Main focus area

6. Video quality

7. Video resolution

8.

Available recording time/Elapsed time

9. Self-timer icon

10.Date and time

11. Focus setting

12. Mode icon

Playback mode

!

[

7

]

!

-

!

Still image playback

1. Voice memo

2. Battery condition

3. Storage media

4. Histogram

5. Image quality

6. ISO

7. Image size resolution

8. File number

9. Folder number

10.Date and time

11. Exposure value

12.Aperture value

13.Shutter speed value

14. DPOF icon

15.Protect icon

16. Mode icon

Playback mode

!

[

7

]

!

-

!

Video playback

1. Video status bar

2. Elapsed time

3. File number

4. Folder number

5. Play mode

6. Mode icon

7.

Protect icon

8. Total recorded time

00 : 21

x4.0

1 2

3

7

8 9

4

5

6

10

11

12

100 - 0001

Total

00 : 00 : 08

Play

00 : 00 : 01

00:00:01

E

1

6 5 4 3

8

7

2

EN-12

GETTING STARTED

Preparation

1. Attach the camera strap.

2. Open the battery/memory card cover.

3. Insert the supplied battery with correct orientation

as shown.

4. Insert an SD/SDHC memory card (Optional).



The camera has

32MB internal memory

(approx. 28MB available for image storage)

,

but you can load an SD/SDHC memory card to

expand the camera’s memory capacity.

 Be sure to format the memory card with this

camera before its initial usage.

5. Close the battery/memory card cover and make sure

it is locked securely.



To prevent valuable data from being accidentally erased from an

SD/SDHC memory card

, you can slide the write protect tab (on

the side of the

SD/SDHC

memory card) to “LOCK”.

 To save, edit, or erase data on an SD/SDHC memory card,

you must unlock the card/

 To prevent damaging of an SD/SDHC memory card, be sure

to turn off the power when inserting or removing the SD/SDHC

memory card. If inserting or removing the SD/SDHC memory

card with the power on, the camera will automatically turn off.

EN-13

Charging the Battery

Charge the battery fully with the supplied battery charger before use.

1. Insert the battery into the battery charger.

2. Connect the power cord to the charger and

insert the plug into a wall outlet.

 The status LED on the charger lights red

when charging has started and lights

green when charging is completed. The

LED also lights green if no battery is

inserted into the charger.

 Charging time varies according to the

ambient temperature and the status of battery.

 Remove the battery after charging is completed.

 The battery may feel warm after it has been charged or immediately after being used. This is

normal and not a malfunction.

 When using the camera in cold areas, keep the camera and battery warm by holding them inside

your outer clothes.

2

1

EN-14

Initial Settings

Setting the Date and Time

The date/time needs to be set if and when:

 The camera is turned on for the first time.

 The camera is turned on after leaving the camera without the battery for an

extended period of time.

When the date and time information is not displayed on the LCD monitor, follow these

steps to set the correct date and time.

1. Toggle the MODE button to [8] or [

B]; or press

the [

7

]

button

.

2. Press the MENU button.

3. Select [Setup] with the f button.

4. Select [Date/Time] with the c / d buttons, and

press the SET button.

5. Select the date format with the c / d buttons,

and press the SET button.

 Select the item’s field with the e / f buttons

and adjust the value for the date and time

with the c / d buttons.



The time is displayed in 24-hour format.



After confirming all settings are correct, press

the

SET

button.

6. To exit from the [Setup] menu, press the MENU

button.

EN-15

Choosing the Language

Specify in which language menus and messages are to be displayed on the LCD

monitor.

1.

Toggle the MODE button to [8] or [B]; or press

the [

7

]

button.

2. Press the MENU button.

3. Select [Setup] menu with the f button.

4. Select [Language] with the

c

/

d

buttons and

press the

SET

button.

5. Select the displayed language with the

c

/

d

buttons and press the

SET

button.

 The setting will be stored.

Formatting the Memory Card or Internal Memory

This utility formats the internal memory (or memory card) and erases all stored images

and data.

1. Toggle the MODE button to [8] or [B]; or press

the [

7

]

button

.

2. Press the MENU button.

3. Select [Setup] menu with f button.

4. Select [Format] with the

c

/

d

buttons, then

press the

SET

button.

5. Select [Execute] with the

c

/

d

buttons, and

press the

SET

button.



To cancel formatting, select [Cancel] and

press the

SET

button.

EN-16

CAPTURE MODE

Capturing Images

Your camera is equipped with a 3.0" full colour TFT LCD monitor to help you compose

images, playback recorded images/video clips or adjust menu settings.

1. Press the ON/OFF button to turn the power on.

 The status LED lights green and the camera is initiated.

2. Toggle the MODE button to [8].

3. Compose your image in the LCD monitor.

 Slide the zoom lever to =/X side to zoom in on the subject, and enlarges the

subject on the LCD monitor.

 Slide the zoom lever to >/Y side to zoom out on the subject, and provides a

wider angle image.

4. Press the shutter button.

 Pressing the shutter button down halfway

automatically focuses and adjusts the

exposure, and pressing the shutter button

down fully captures the images.

 The focus area frame turns green when the

camera is in focus and the exposure is

calculated.

 When the focus is not suitable, the frame of

the focus area turns red.

1

2

EN-17

Taking Images When the Smile Feature Is On

With the camera’s new “smile detection” function, this camera detects smiles so you do

not miss those special moments in life.

1. Toggle the MODE button until the scene mode

selection screen appears.

2. Select [Smile Shot] with the e / f buttons, and

press the SET button.

3. Compose the image, and press the shutter button

down fully.

4. Once the camera detects a smile, it will

automatically capture 3 images (by default, the flash

mode setting is set to

d).

 If the flash mode setting is changed to

a, the

camera will only capture an image after it detects

a smile.

 When capturing group shots (if the number of

people is more than 1), the camera will

automatically capture the image(s) when it

detects two smiles. The number of shots taken

depends on the flash mode setting.

 If the camera does not detect a smile within 5

seconds, the camera returns to preview display.

 Press the shutter button once again to reactivate

this function.

!

EN-18

Recording Shots into Multiple Image Layout

The Album Shot mode enables you to easily record images and combine three shots into a

single image.

1. Toggle the MODE button to [8].

2. Press the MENU button, and select the [Function] menu with the f buttons.

3. Select [Capture Md.] with the c / d buttons, and press the SET button.

4. Select [Album Shot] with the c / d buttons, and press the SET button.

5. Press the MENU button.

6. Press the shutter button to capture the first image.

7. Press the shutter button again to capture the second and third images.

 Pressing the SET button during step 2 or 3 will delete the last captured image.

 The camera returns to normal preview display by pressing the d button. Press the d

button again to switch back to album shot preview display.

 This shot can only be recorded if there are 3 shots recorded in each of the available

frames.

Recording Shots using Face Detection Technology

Face Detection Technology can identify and focus on the human faces in the image. This

advanced function simultaneously detects up to 5 human faces regardless of their position in

the scene.

1. Toggle the MODE button to [8].

2. Toggle the OZ button until [Z] icon appears on the LCD monitor.

 The white frame is identified as the “top priority” face (main focus frame), and gray

ones around the other faces.

3. Press the shutter button halfway down to lock the focus.

 The main focus frame simultaneously turns green.

 If the “top priority” face is out of focus, all frames will be disappeared from the screen.

4. Press the shutter button down fully to capture your image.

 Subjects that are not suitable with this function:

a. A person wearing glasses, sunglasses, or face covered with hat or hair.

b. A person turning sideways.

EN-19

Setting the Scene Mode

By simply selecting one of the following 21 modes, you can capture the image with the

most!appropriate settings.

1. Toggle the MODE button until the scene mode

selection screen appears.

2. Select the desired scene mode with the e / f

buttons, and press the SET button.

3. Compose the image and press the shutter button.

The table below will help you choose the appropriate scene mode:

Scene mode Description

W Smile Shot Select this mode to automatically capture an image when a smiling

face is detected.

n Anti-Shake This mode minimizes the influences of hand shaking when you want

to capture an image.

T Panorama Select this mode when you want to capture a series of shots then

stitch them together with software to make a single photo.

QPortrait Man Select this mode when you want to capture an image that makes a

man stand out against a blurred background.

RPortrait Lady Select this mode when you want to capture an image that makes a

lady stand out against a blurred background.

l Landscape Select this mode when you want to capture an image with infinity

focus, hard sharpness and high saturation.

l Sports Select this mode when you want to capture fast-moving subjects.

g Night Portrait Select this mode when you want to capture people with an evening or

night scene background.

h Night Scene Select this mode when you want to capture dark scenes such as night

views.

c Candlelight Select this mode when you want to capture photos of candlelit scene,

without spoiling the ambience.

d Fireworks Select this mode when you want to capture fireworks clearly with

optimal exposure. The shutter speed becomes slower, so using a

tripod is recommended.

!

La pagina sta caricando ...

Hitachi HDC-1098EP Manuale del proprietario

Questo manuale è adatto anche per

Hitachi HDC-1098EP Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti