General Music rp-x Manuale del proprietario

D I G I T A L K E Y B O A R D S

•English

Owners manual

rp-x

•Italiano

•Deutsch

•Français

D I G I T A L K E Y B O A R D S

•English

Owners manual

rp-x

The information contained in this manual are considered correct at the moment of printing. Generalmusic reserves the

right to change or modify any technical speciﬁcation without prior notice or obbligation to upgrade existing units.

SPECIAL MESSAGES

IMPORTANT NOTE: To reduce the risk related to the correct and normal use of the instrument, all Generalmusic products are accuralety tested

in a safety laboratory. DO NOT modify the present unit, the safety standard and the correct instrument operativity could be compromised, and as

a further consequence the warranty will be invalidated.

ALARM SYMBOLS:

Generalmusic electronics products

could present labels similar to that

displayed in this section. Please follow

accurately the precautions descripted

in the safety instructions.

The exclamation mark within an equilateral triangle is

intended to alert.

The lightning ash with arrowhead symbol, within an equilat-

eral triangle, is intended to alert the user to the presence of

uninsulated “dangerous voltage” within the product’s enclo-

sure that may be of sufcient magnitude to constitute a risk of

electric shock to persons.

SAVE THESE INSTRUCTIONS

Generalmusic cannot be held responsible for damage caused by improper use or modiﬁcations to the

instrument, or data lost or destroyed

IMPORTANT SAFETY AND INSTALLATION INSTRUCTIONS

When using electric products, basic precautions should always be followed, including the following:

1. Read all the Safety and Installation instructions and explanations of Graphic Symbols before using the product.

2. This product must be earthed. If it should malfunction or breakdown, grounding provides a path of least resistance for electric

current to reduce the risk of electric shock. This product is equipped with a cord having an equipment-grounding conductor and a

grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and earthed in accordance with all

local codes and ordinances.

DANGER:Improper connection of the equipment grounding conductor can result in a risk of electric shock. Check with a qualied electrician or serviceman if you are

in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product, if it will not t the outlet, have a proper outlet installed by a

qualied electrician.

3. To reduce the risk of injury, close supervision is necessary when this product is used near children.

4. Do not use this product near water for example, near a bathtub, washbowl, kitchen sink, in a wet basement, or near a swimming

pool or the like.

5. This product should only be used by a stand or cart that is recommended by the manufacturer.

6. This product, either alone or in combination with an amplier and headphones or speakers, may be capable of producing sound levels that could

cause permanent hearing loss. Do not operate for a long period of time at a high volume level or at a level that is uncomfortable. If you experience

any hearing loss or ringing in the ears, you should consult an audiologist.

7. This product should be located so that its location or position does not interfere with its proper ventilation.

8. This product should be located away from heat sources such as radiators, heat registers, or other products that produce heat.

9. The product should be connected to a power supply only of the type described in the operating instructions or as marked on the product.

10. This product may be equipped with a polarized line plug (one blade wider than the other). This is a safety feature. If you are unable to insert the plug

into the outlet, contact an electrician to replace your obsolete outlet. Do not defeat the safety purpose of the plug.

11. The power-supply cord of the product should be unplugged from the outlet when left unused for a long period of time. When unplugging the power

supply cord, do not pull on the cord but grasp it by the plug.

12. Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings.

13. The product should be serviced by qualied service personnel when:

A. The power-supply cord or the plug has been damaged

B. Objects have fallen, or liquid has been spilled into the product;or

C. The products has been exposed to rain or moisture

D. The product does not appear to be operating normally or exhibits a marked change in performance

E. The product has been dropped, or the enclosure damaged.

14. Do not attempt to service the product beyond that described in the user-maintenance instructions. All other servicing should be referred to qualied

service personnel.

15. WARNING - Do not place objects on product power cord or place it in a position where anyone could trip over, walk on or roll anything over it. Do

not allow the product, or its bench, or its pedal board to rest on or to be installed over power cords of any type. Improper installations of this type

create the possibility of re hazard and/or personal injury.

16. Electromagnetic interference (RFI). This electronic product utilizes digital sampled wave processing technology (S.W.P.) that may adversely affect

radio/tv reception. Read FCC information inside back cover for additional information.

INSTRUCTION PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS.

The illustrations and the screens of this manual are for instructional purposes only and may appear different from

those on your instrument.

WARNING!

This marking shown on the product or its literature, indicates that it should

not be disposed with other household wastes at the end of its working life. To

prevent possible harm to the enviroment or human health from uncontrolled

waste disposal, please separate this from other types of wastes and recycle it

responsibly to promote the sustainable reuse of material resources. Household

users should contact either the retailer where they purchased this product, or

their local government of ce, for details of where and how they can take this

item for environmentally safe recycling. Business users should contact their

supplier and check the terms and conditions of the purchase contract. This

product should not be mixed with other commercial wastes for disposal.

The declaration of conformity can be downloaded from the

Generalmusic website:www.generalmusic.com

Technical speciﬁcations are subject to change

M A N U A L I N D E X

Introduction

1

Front Panel

1

Rear panel and connections

1

Getting started

2

Power the expander

2

Connect a speaker system

2

Connect a midi master controller

3

Connect pedals

3

Using the input connection

3

Connect The Rp-x To A Pc 4

Connect To A Pc Via Midi 4

Connect To A Pc Via Usb 4

Start the rp-x

5

Listen to the demo sequence

5

The Default Performance Mode

5

Select the performances

6

Manual recalling

6

Midi recalling

6

Edit the performance

7

Selecting the parts (ch)

7

Selecting the parameters to edit in the selected parts (ch): sound

8

Selecting the parameters to edit in the selected parts (ch): volume

8

Selecting the parameters to edit in the selected parts (ch): velocity

9

Selecting the parameters to edit in the selected parts (ch): trans-

9

Selecting the parameters to edit in the selected parts (ch): tune

9

Selecting the parameters to edit in the selected parts (ch): efx

9

Selecting the parameters to edit in the selected parts (ch): rev

10

The mode "ALL" in edit menu

10

Memorize the performance

11

Store the edit in the same performance location

11

Store the edit in a different performance location

11

Exit the performance store

12

Copy the performance

12

Memory management system

13

Common channel setting

13

Midi identification number

13

System reset

14

Midi data bulk (dump)

15

Sound list

16

Performance list

17

Technology

18

Technical specifications

19

Midi implementation chart

19

rp-x Product Package

• rp-x expander

• Owners manual

• Gem PC - Software Editor

• AC Adapter

• MIDI Cable

Page 1

owners manual

rp-x

r p - x

$# 53"

). /544(25

-)$)

0%$!,3

 ,2

).054

/54054

,

2-

INTRODUCTION

FRONT PANEL

1

2

3

4

These buttons allows to modify the parameters value.

The two buttond pressed at the same time start the

DEMO sequence.

5

This button enter the edit mode and select the editing

parameters.

6

7

the Volume knob, set the output level of the instru-

ment.

8

This button switch on or off the instrument.

Adapter input, in order to avoid hardware problem

with this unit, please use the adapter included in the

module package only.

1

2 3

4 5 6

7

8

2

USB connection to the PC. Use this connection with a

proper USB cable to connect the module to a PC. See

the relative chapter in this manual.

2

3

The three standard MIDI ports allows the connection of

the instrument to a MIDI controller, such as a Master

keyboard a Midi Accordion or a PC (equipped with

MIDI interface).

3

4

it's possible to connect two type of pedals to the ex-

pander, an Expression pedal to the Input #2 and a

Gem Multipedal unit to the Input #1.

4

5

The INPUT RCA connectors allows to plug an external

(Line) source to the instrument. Consult the relative

chapter of this user manual.

5

6

Connect the instrument to an external speaker system

or a Mixer.

6

These jack connectors allows to plug two headphones

to the module.

The perf button (PERFORMANCE), select the per-

formance mode. See the relative chapter, in this

manual.

This led monitoring the midi data received to the midi

input of the module.

The 3 digit display visualize the values and the pa-

rameters of the various editing levels.

display

midi

perf

phones edit

volume

data entry/demo

on/off

REAR PANEL AND CONNECTIONS

12 D.C. in

USB

MIDI IN-THRU-OUT

PEDALS

INPUT

OUTPUT

Congratulations & thank you for purchasing the GEM rp-x Expander. Utilizing our

proprietary DRAKE technology, the rp-x produces a vast variety of acoustic and electric

piano sounds with exceptional quality. The rp-x also incorporates an intuitive, yet easy to

use operational interface that will satisfy even the most demanding live or professional

studio applications.

1

Page 2

owners manual

rp-x

$# 53"

). /544(25

-)$)

0%$!,3

 ,2

).054

/54054

,

2-

$# 53"

). /544(25

-)$)

0%$!,3

 ,2

).054

/54054

,

2-

r p - x

GETTING STARTED

Connect the adapter to a proper voltage A.C. wall

plug.

1

POWER THE EXPANDER

Connect audio output of the expander to your live or

studio speaker system.

2

The rp-x expander is a professional suond generator with a top quality pcm physical/modelling sound

library. Always use an adequate stereo external speaker system in order to get the maximum performance

from this instrument.

CONNECT A SPEAKER SYSTEM

Connected to desktop or laptop PC via MIDI or USB in a MIDI network2

Played via MIDI from a MIDI master controllers such as a digital piano, a master keyboard,

a MIDI guitar, a MIDI accordion.

1

Start the

rp-x

Set the

global

volume

NOTE: always turn on the speaker of your system after all the others devices.

The Gem rp-x expander is a top quality piano sound generator, designed to be used in the following ways :

In this chapter we will cover all the basic steps necessary to properly connect and use the instrument.

Page 3

owners manual

rp-x

$# 53"

). /544(25

-)$)

0%$!,3

 ,2

).054

/54054

,

2-

MIDI OUT

MIDI IN

$# 53"

). /544(25

-)$)

0%$!,3

 ,2

).054

/54054

,

2-

MIDI IN

MIDI OUT

MIDI MASTER KEYBOARD

MIDI Accordion

$# 53"

). /544(25

-)$)

0%$!,3

 ,2

).054

/54054

,

2-

$# 53"

). /544(25

-)$)

0%$!,3

 ,2

).054

/54054

,

2-

SPEAKER SYSTEM

MIDI IN

MIDI OUT

AUDIO OUT

$# 53"

). /544(25

-)$)

0%$!,3

 ,2

).054

/54054

,

2-

MIDI IN

MIDI OUT

EXPRESSION pedal

code �970013

MULTIPEDAL

prod. code �970464

SUSTAIN pedal

prod. code

�970116

SUSTAIN pedal PIANO TYPE

prod. code

�970134

r p - x

MIDI IN

MIDI OUT

MIDI THRU

AUDIO

OUTPUT TO

SPEAKER

$# 53"

). /544(25

-)$)

0%$!,3

 ,2

).054

/54054

,

2-

MIDI IN

INPUT

OUTPUT

Rear Panel

CONNECT A MIDI MASTER CONTROLLER

USING THE INPUT CONNECTION

The rp-x module can be used as a powerful piano sound expansion for any type of MIDI controller, digital

piano, master keyboard, MIDI guitar and accordion.

In order to achieve the maximum control of the rp-x, please refer to this next chapter where the different

parts of the instrument will be fully explained.

CONNECT PEDALS

It is not possible to change these parameters set from the rp-x internal edit menu. However using the advanced

PC editor supplied with the module, it’s possible to edit some of these parameters in a very detailed way.

The rp-x is equipped with RCA stereo input connections. These jacks allow you to connect another instru-

ment (or external LINE audio source) and mix the signal into the audio OUTPUT of the module.

Please note that the external mixed signal will be not processed in any way from the rp-x, this is a dry input only.

This connection allows you to use two mixer inputs to connect a digital piano and the rp-x at the same time.

In the same way, using the input connection it's possible to connect the rp-x to a gm-x (GM compatible module).

T he EX P R E SS I O N

pedal can be con-

nected to the Pedal

Input #2 only

Independently of the MIDI or USB controller you're using with the rp-x, it's possible to connect directly to

the module various type of pedals: single switch, multi switch, continuos control.

Page 4

owners manual

rp-x

$# 53"

). /544(25

-)$)

0%$!,3

 ,2

).054

/54054

,

2-

r p - x

$# 53"

). /544(25

-)$)

0%$!,3

 ,2

).054

/54054

,

2-

SPEAKER SYSTEM

PC MIDI OUT

MIDI IN

Not included

CONNECT TO A PC VIA MIDI

CONNECT TO A PC VIA USB

to the speaker systemD.C. adapter

USB cable

CONNECT THE rp-x TO A PC

The Rp-x expander can be connected to a PC in two different way: using the MIDI or the USB (Universal Serial

Bus) interface. Using the MIDI the PC has to be equipped with a proper MIDI interface (see the note below), in

case of USB it's possibile to use directly the PC USB built-in connection. In both case, MIDI or USB, the tranfer

rate and the features of the protocol are complying the standard MIDI speciﬁ cations, the only difference consist

of the connections type.

NOTE: Normally the desktop PC offers the MIDI connection from the installed audio card. The type of the connection

it depend from the model of the audio card. About this purpose, please refer to the owner manual of your PC.

gem X-series

editor Soft-

ware

You can use the rp-x connected to a PC or to play its sound via MIDI from a software sequencer or to create or edit

the internal performances (see the next chapter), using the PC editor included in the instrument package.

We will assume that a MIDI interface along with software to play MIDI ﬁ les is correctly installed in your PC. Please refer

to the operating instructions of these devices to properly conﬁ gure the PC to transmit standard MIDI ﬁ les via the MIDI

OUT socket.

REMEMBER! The MIDI interface does not transmit AUDIO signals, just control

data only. You must always connect the audio output of the MIDI instrument

(such as the rp-x) you are controlling, to an external speaker system

For instruction on this feature, please refer to the CD ROM included with the expander.

As previously noted, the only difference in MIDI or USB is only the type of connections, the data transfer rate and the

features are the same in both cases.

MIDI OUT

MIDI IN

Page 5

owners manual

rp-x

r p - x

THE DEFAULT PERFORMANCE MODE

After powering up the rp-x, the instrument defaults to the PERFORMANCE mode. The LED of the relative

button on the panel will illuminate. The rp-x is now ready to be played.

The Performance mode consist of a complete set of parameters including sounds, volume, transpose, tuning, reverb, efx,

etc. And up to four multi-timbral PARTS.

The PERFORMANCE (PERF) mode is the rp-x main operating level to play and perform. This mode allows

you to program and recall in real time, up to 99 different set ups.

The data stored in the PERF mode is memorized when the instrument is powered off.

The rp-x comes with a complete set of pre-programmed performances. These performance are designed to

highlight the sound and power of this instrument.

Severeal of the factory programmed performances utilize Split or Layer mode. In order to hear all PARTS used

in any of the factory programmed Split or Layered performances, your MIDI master controller must be assegned

to transmit on MIDI channel 1. See ahead for further details in the chapter named MIDI COMMON Channel.

START THE rp-x

LISTEN TO THE DEMO SEQUENCE

For a complete listing of the factory programmed Performances, please refer to page 17 of this owner’s

manual.

Once the rp-x module is connected to your controller, it's possible to use it, in the

way you prefer.

Use the ON/OFF button on the front panel to switch on the module.

The rp-x has an internal DEMO sequence demonstrating the musical quality & power

of the instrument. Press the two DATA ENTRY buttons on the panel at the same time

in order to start the DEMO. The display show the message “DE1” (Demo 1).

Playing the DEMO. Adjust the instrument output VOLUME, by rotating the VOLUME

knob on the panel.

The DEMO sequence contains various songs from different musical

styles. During playback it’s possible to select each demo song, by simply

pressing the DATA button. The display will indicate the number of

the selected DEMO song. In the normal DEMO mode, all the songs will

be played in chain.

You can exit The DEMO mode by pressing the PERF button on the panel. The

module will return the default mode.

Page 6

owners manual

rp-x

r p - x

Performance - Performance +

MIDI MASTER KEYBOARD

MIDI IN

MIDI OUT

r p - x

MIDI MASTER KEYBOARD

MIDI IN

MIDI OUT

r p - x

1

4

7

- 0

8

5

2

+

9

6

3

MIDI MASTER KEYBOARD

MIDI IN

MIDI OUT

r p - x

1

4

7

- 0

8

5

2

+

9

6

3

SELECT THE PERFORMANCES

It is possible to recall the internal 99 performances rp-x in two different way.

MANUAL RECALLING

Please consult the PERF list on page 17 to visualize the performance

names and theyr structure (single, layer, Split, etc.).

MIDI RECALLING

Please note the MIDI transmission channel of the MIDI controller has to be set to the MIDI ch. # 01

Press the DATA buttons to select the internal

performances.

From your MIDI controller send the MIDI Program Change corresponding to the PERFOMANCE you wish to

recall. (Prg. Cng �01 select PERF �01, Prg. Cng �02 select PERF �02 etc.)(Prg. Cng �01 select PERF �01, Prg. Cng �02 select PERF �02 etc.)

The way to transmit the MIDI Program Change can differ from one MIDI controller to another, please refer

to the owners manual of your MIDI controller in regards to this purpose.

Page 7

owners manual

rp-x

r p - x

EDIT THE PERFORMANCE

In the rp-x it's possible quickly modify (edit) the factory pre programmed performance according to your

needs. The PERFORMANCE mode possesses a very important feature, it’s possible to store (and recall), in

the instrument memory 99 different settings, which are retained in the modules memory after turning off

the instrument.

Press the EDIT button on the panel to enter the

PERF edit mode.

The PART (CH) parameter is automatically selected, mean-

while its current value it's visualized in the display

NOTE

Modifying any default parameters value, the PERF

LED on the panel start blinking, visualizing the

editing status.

1

2

In the rp-x it is possible to select 4 different parts, corresponding to the MIDI channel #01, #02, #03, # 04.

SELECTING THE PART (CH)

Press repeatedly the DATA button, the display will

show the PART (CH) number you wish to edit.

The parameter set directly available from the panel of the rp-x module is a reduced set than available in the in-

strument, (this is due to the simplified navigation system used in the module). The best way to fully edit the rp-x

performance is to use the PC EDITOR software included in the package. This software allows you to easily create or

edit all kinds of performances!

Once all the 4 MIDI channel have been selected, the

display will show the message ALL. This condition allows

you to modify some parameters values at the same time,

speeding up the editing operation. See ahead for further

details.

Please consult page 8 to move on the editing menu next pa-

rameter.

Page 8

owners manual

rp-x

r p - x

SELECTING THE PARAMETERS TO EDIT IN THE SELECTED PARTS (CH): SOUND

The current default value of the selected parameter, is show

in the display. In the part number 1 the sound is: GRAND

PIANO. Please refer to the sound list included on page 16

of this manual.

SELECTING THE PARAMETERS TO EDIT IN THE SELECTED PARTS (CH): VOLUME

Volume -

Volume +

Part disabled

The rp-x has a database with 50 sounds in total. Please

consult the complete list on Page 16.

Once you have selected the PART you wish to modify

(#01 in this example), the EDIT menu parameter are

selected by pressing the EDIT button. Each time you

press the button a different parameter is selected.

Pressing the DATA button you select the next sound

in the sound database.

Each time you press the DATA button a next sound

is selected.

To select the VOLUME parameters of the selected

PART (CH) sound, press the EDIT button once more

time. The current default value of the parameter

is indicated in the display. Volume = 105 in this

example.

You can increase or decrease the volume level, by

pressing the DATA buttons. The display show

you in realtime the value changing.

Once you have reached the VOLUME = 000, (minimum sound

level), by pressing once more again the DATA button you'll set

the selected part OFF, then the part is disabled.

NOTE

It's possible to restore the VOLUME default value by pressing the two

DATA buttons at the same time.

NOTE

Modifying any default parameters value, the PERF LED on the

panel start blinking, visualizing the editing status.

Page 9

owners manual

rp-x

r p - x

EFX -

EFX +

SELECTING THE PARAMETERS TO EDIT IN THE SELECTED PARTS (CH): VELOCITY

Press the EDIT button to select the VELOCITY param-

eter. The display indicates the current default value,

in this example.

Velocity - Velocity +

NOTE

SELECTING THE PARAMETERS TO EDIT IN THE SELECTED PARTS (CH): TRANSPOSE

SELECTING THE PARAMETERS TO EDIT IN THE SELECTED PARTS (CH): TUNE

NOTE

Transpose - Transpose +

Tune -

Tune +

SELECTING THE PARAMETERS TO EDIT IN THE SELECTED PARTS (CH): EFX

This parameter allows you to set a programmable VELOCITY offset , in order to increase or decrease the

velocity value of incoming MIDI notes transmitted by a MIDI controller. Value range: -64/00/+63. Value=00

does not affects the original velocity values.

If you need it, You can set the VELOCITY value, by

pressing the DATA buttons. The display show you

in realtime the value changing.

The parameter VELOCITY it's GLOBAL, then its setting will affect ALL the parts at the same time. For this reason it can be

selected if the "ALL" mode has been enabled only. About the "ALL" mode please consult pages #7 and #10 .

It is possible to restore the VELOCITY, TRANSPOSE and TUNE default value , by pressing the two DATA buttons at the same time.

TRANSPOSE allows to shift the PART (CH) pitch in a range of +/- 24 semitones.

Press the EDIT button to select TRANSPOSE. The dis-

play indicates the current default value

(TRANSPOSE=00, C=C), in this example.

Pressing the DATA buttons to increase or de-

crease the PART transpose. The display show you in

realtime the value changing. Each single step (+/- 24)

correspond to a semitone.

TUNE allows you to shift the PART (CH) pitch ﬁne tuning in a range of : - 64/00/+ 63.

Press the EDIT button to select TUNE. The display

indicates the current default value (TUNE= 00), in

this example.

Pressing the DATA buttons to increase or de-

crease the PART TUNE. The display show you in

realtime the value changing.

Set the EFX send level (chorus, tremolo, phaser, delay etc.) in the selected PART.

Press the EDIT button to select the EFX. The display

indicates the current default value (EFX = 000), in

this example.

Pressing the DATA buttons to increase or de-

crease the EFX send in the selected part. The display

shows you in realtime the value changing. The pa-

rameter range is from 0 to 127.

Page 10

owners manual

rp-x

r p - x

REV -

REV +

r p - x

Tune -

Tune +

Etc.

SELECTING THE PARAMETERS TO EDIT IN THE SELECTED PARTS (CH): REV

THE MODE "ALL" IN EDIT MENU

As already described in the previuos page, the ALL

mode is a way offer by the rp-x system to speed up

the editing operation for some parameters.

In fact setting the ALL mode in PART (CH) edit and selecting one of the edit parameters (*), the value you insert

affects all the parts at the same time.

(*) The SOUND selection it's excluded from the ALL mode.

VOLUME

In ALL MODE sets the GENERAL volume of the instrument.

VELOCITY

Allows you to set a programmable VELOCITY offset , in order to increase or decrease the velocity value

of incoming MIDI notes transmitted from a MIDI controller. Value range: -64/00/+63.

Value = 00 does not affects the original velocity values.

TRANSPOSE

Sets the GLOBAL transpose of the module +/- 12 semitones. This value is added to the PART value.

The total transpose value is: +/- 36 semitones (+/- 24 semitones in PART, plus +/- 12 semitone in

ALL mode).

TUNE

Control the GLOBAL tune of the module, from A = 427 to A= 452 Hz.

EFX

Control the effect (EFX) general level.

REV

Control the reverb (REV) general level.

Selecting the "ALL "mode the TUNE becomes a GLOBAL pa-

rameter. Editing this parameter the display indicates the detune

values in step of HERTZ. Range: from A = 427 to A= 452 Hz.,

A=440 standard default value.

NOTE

Set the REVERB (REV) level in the selected PART.

Press the EDIT button to select the REV. The display

indicates the current default value (REV = 024), in

this example.

Pressing the DATA buttons to increase or de-

crease the REV send in the selected part. The display

shows you in realtime the value changing. The pa-

rameter range is from 0 to 127.

Page 11

owners manual

rp-x

r p - x

MEMORIZE THE PERFORMANCE

STORE THE EDIT IN THE SAME PERFORMANCE LOCATION

STORE THE EDIT IN A DIFFERENT PERFORMANCE LOCATION

Once your PERFORMANCE edit it's complete press the

blinking PERF button on the display.

At this point both the PERF button and the digit

"P01" in the display (indicating the number of the

edited performance in this example), blink at the

same time.

Keep the PERF button pressed at least for 2 seconds

to store in the current location. The display show the

message "STR" (STORE).

1

2

3

Once your PERFORMANCE edit it's complete press the

blinking PERF button on the display.

1

At this point both the PERF button and the digit "P01"

in the display (indicating the number of the edited

performance, N.01 in this example), blink at the

same time.

2

It's now possible to select another PERF location using

the DATA buttons. It's possible to select any of

the 99 available memory locations.

3

Once the desidered memory location is reached, keep

the PERF button pressed at least for 2 seconds to store

data. The display show the message "STR" (STORE).

4

The PERF LED and the display will stop blinking, the

PERF number is showed again to comfirm the STORE

operation.

4

5

The PERF LED and the display will stop blinking and

the PERF number is showed again to comfirm the

STORE operation.

Page 12

owners manual

rp-x

r p - x

EXIT THE PERFORMANCE STORE

COPY THE PERFORMANCE

Once your PERFORMANCE edit it's complete press the

blinking PERF button on the display.

1

At this point both the PERF button and the digit

"P01" in the display (indicating the number of the

edited performance in this example), blink at the

same time.

2

3

Select a performance to be copied.

1

Press the EDIT button

2

Press the PERF button in the display, the selected

performance number start blinking on the display.

3

Select a destination memory PERFORMANCE location

using the DATA buttons.

4

Keep the PERF button pressed to STORE the PERFOR-

MANCE in the new location.

5

The PERF LED and the display will stop blinking.

The PERF number is showed again on the display to

comfirm the STORE operation. The EDIT button LED

goes OFF

5

The selected PERFORMANCE is the SOURCE performance, the data contained in this location will be copied in a destination

memory location you'll select in the next stage #4

At this stage it's possible to exit the STORE procedure

by simply pressing the EDIT button. The LED will stop

blinking and the edited data will be deleted. The

display show again the PERF number you start to

edit, while the EDIT button LED goes OFF.

Use the DATA buttons to select a PERFORMANCE

location. It's possible to select any of the 99 available

memory locations.

To help the edit operation the module allows you to copy the PERFORMANCE data to any other available location. In

this way it's easier to create, for example, different versions of the same split or layer PERFORMANCE.

Page 13

owners manual

rp-x

r p - x

MEMORY MANAGEMENT SYSTEM

COMMON CHANNEL SETTING

It is possible to select as MIDI COMMON channel any of the 16

available MIDI channels. As you can see the default of the MIDI

COMMON is set on ch. #1.

MIDI IDENTIFICATION NUMBER

This function allows to use more than one expander in a MIDI network, assigning an identiﬁcation number of the ex-

pander. This function is really useful using the rp-x PC editor, where even the software allows to ﬁx an identiﬁcation

number, in this case it's possible to work with a MIDI sistem composed from two or more rp-x module and the relative

editors without conﬂict.

Enter the MEMORY MANAGEMENT SYSTEM mode keep-

ing pressed al least for 2 seconds the PERF and the EDIT

buttons at the same time. As already seen the first menu

is the MIDI COMMON channel setting.

Press the EDIT buttons to select the MIDI ID menu, the

display show the default ID set on �01 (ALL MODE).

Press the PERF button to exit the COMMON CHANNEL

setting mode. The LED on the display stop blinking and

the instrument select the default mode.

This menu contains some important function for the global instrument setting:

These setting are automatically stored in the expander memory and also saved switching ON/OFF the instrument.

•COMMON CHANNEL SETTING

•MIDI IDENTIFICATION NUMBER

•SYSTEM RESET

•MIDI DATA BULK

To enter the MIDI COMMON channel setting mode keep

al least for 2 seconds the PERF and the EDIT buttons

pressed at the same time.

Both the pressed button and the PART (CH) LED will blink

in the instrument.

The MIDI COMMON channel is a very useful function allowing a high grade of versatility in MIDI programming.

In the default assign the COMMON channel allows you to control the performances playing and selection using

the MIDI ch.#01 only. Many of the internal rp-x performance are programmed using different parts (and differ-

ent MIDI channel) in layer or split mode. The MIDI COMMON allows to fully play and select these performances

using a master MIDI controller transmitting in a single MIDI channel.

Set the new COMMON using the DATA buttons

Press the PERF button to exit the COMMON CHANNEL

setting mode.

The LED on the display stop blinking and the instrument

select the default mode.

Select a different MIDI ID according with your needs using

the DATA buttons. Value Range 0-15.

Page 14

owners manual

rp-x

r p - x

SYSTEM RESET

Enter the MEMORY MANAGEMENT SYSTEM mode keep-

ing pressed al least for 2 seconds the PERF and the EDIT

buttons at the same time. As already seen the first menu

is the MIDI COMMON channel setting.

Both the pressed buttons and the PART (CH) LED will blink in

the instrument.

This function restore the original programmed factory set up of the entire instrument.

Press the EDIT button again, the display show the flash-

ing message "RST", RESET. The RESET menu it's now

selected.

Keep the DATA button pressed at least 2 sec. to reset

the instrument. Once the message "RST" in the display

stops blinking the factory data set up is restored.

Press the EDIT buttons again and the MIDI ID menu is

selected.

Press the PERF button to exit the menu and select the

default mode.

La pagina sta caricando ...

General Music rp-x Manuale del proprietario

General Music rp-x Manuale del proprietario

in altre lingue

Altri documenti