Yamaha CRW3200E Manuale utente

Marca: Yamaha

Modello: CRW3200E

Categoria: Unità disco ottico

Tipo: Manuale utente

Questo manuale è adatto anche per

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party: Yamaha Electronics Corporation, USA.

Address: 6660 Orangethorpe Avenue

Buena Park, CA 90620

Telephone: 714-522-9105

Fax: 714-670-0108

Type of Equipment: CD Recordable/Rewritable Drive

Model Name: CRW3200

CRW3200NB

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference that

may cause undesired operation.

See user manual instructions if interference to radio reception is suspected.

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements.

Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables.

Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void

your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class

“B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product

in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses

radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause

interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that

interference will not occur in all installations. If this product is found to be the source of interference, which can be determined

by turning the product “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by the interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change

the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this

type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corporation, USA.

6660 Orangethorpe Avenue, Buena Park, CA 90620 U.S.A.

CLASS 1 LASER PRODUCT

LASER KLASSE 1 PRODUKT

LUOKAN 1 LASERLAITE

KLASS 1 LASER APPARAT

PRODUIT LASER DE CLASSE 1

DANGER - VISIBLE AND / OR INVISIBLE LASER

RADIATION WHEN OPEN. AVOID DIRECT EXPOSURE

TO BEAM.

CAUTION - VISIBLE AND / OR INVISIBLE LASER RADIATION WHEN OPEN.

AVOID EXPOSURE TO BEAM.

VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRÅLNING NÄR DENNA

DEL ÄR ÖPPNAD. STRÅLEN ÄR FARLIG.

VARO ! AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA / TAI

NÄKYMÄTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRÅLNING NÄR DENNA DEL

ÄR ÖPPNAD. BETRAKTA EJ STRÅLEN.

VORSICHT ! SICHTBARE UND / ODER UNSICHTBARE LASERSTRAHLUNG

WENN ABDECKUNG GEÖFFNET. NICHT DEM STRAHL AUSSETZEN.

ATTENTION - RADIATION VISIBLE ET / OU INVISIBLE LORSQUE L’APPAREIL

EST OUVERT. EVITEZ TOUTE EXPOSITION AU FAISCEAU.

COMPLIES WITH 21 CFR CHAPTER 1, SUBCHAPTER J.

CAUTION

Use of controls or adjustments or performance of

procedures other than those specified herein may result

in hazardous radiation exposure.

Laser Product Class: Class 1

Laser Diode Properties

Wavelength: 780 – 787 nm

Pulse Durations and Max. Output

at the lens of the Laser Pickup Unit

Read Mode: 0.85 mW (Continuous)

Write Mode: Max. 48 mW

(for 212 ns, Min. Cycle 57.9 ns)

ACHTUNG

Halten Sie sich beim Bedienen und Einstellen der

Bedienungselemente sowie bei der Bedienungsabfolge

an die Anleitung, da sonst gefährliche Strahlen austreten

können.

ATTENTION

L’emploi de commandes, de réglages ou un choix de

procédures différents des spécifications de cette

brochure peut entraîner une exposition à d’éventuelles

radiations pouvant être dangereuses.

PRECAUCION

El usar los controles o ajustar o realizar procedimientos

diferentes a los especificados aquí resultará en

peligrosas exposiciones a la radiación.

VARO! AVATTAESSA JA SUOJALUKITUS OHITETTAESSA

OLET ALTTINA NÄKYMÄTTÖMÄLLE

LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

VARNING! OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR

ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD.

BETRAKTA EJ STRÅLEN. STRÅLEN ÄR FARLIG.

Laserprodukt-Klasse: Klasse 1

Eigenschaften der Laserdiode

Wellenlänge: 780 – 787 nm

Impulsdauer und max. Ausgang an der Linse der

Laser-Abtasteinheit

Lesemodus: 0,85 mW (kontinuierlich)

Schreibmodus: Max. 48 mW

(für 212 ns, Zyklusmin. 57,9 ns)

Classe du produit laser: Classe 1

Caractéristiques de la diode laser

Longueur d’onde: 780 – 787 nm

Durée des impulsions et sortie maximum depuis

la lentille du bloc capteur optique

Mode de lecture: 0,85 mW (continue)

Mode de gravure: max. 48 mW

(pour 212 ns, cycle min. 57,9 ns)

Clase de producto láser: Clase 1

Propiedades del diodo láser

Longitud de onda: 780 – 787 nm

Duración del pulso y potencia de salida máxima

en el objetivo de la unidad captora láser

Modo de lectura: 0,85 mW (continua)

Modo de escritura: máx. 48 mW

(para 212 ns, ciclo mínimo 57,9 ns)

OWNER’S MANUAL

English

SAFETY PRECAUTIONS

PLEASE READ THE FOLLOWING WARNINGS AND CAUTIONS CAREFULLY

TO PREVENT PERSONAL INJURY AND DAMAGE TO THE DEVICE.

These precautions explain how to use the device properly and safely, thereby

preventing injury to yourself and others. This section has been sub-divided into a

WARNING section and a CAUTION section, according to the likelihood and nature

of any potential injuries or damage inflicted. They relate to your personal safety,

and also help you prevent the risk of damage to the device. Please read these

sections carefully prior to proceeding.

WARNING

Always follow these basic precautions to avoid short-circuit, damage, fire, or

other hazards, and to avoid serious injury or fatal accident from electrical shock.

●

Do not attempt to open or disassemble the device to avoid the risk of electrical

shock, fire, or malfunction.

●

Do not look directly at the laser source to avoid the risk of eye damage or

blindness.

●

Do not insert fingers or foreign objects into the device to avoid the risk of

electrical shock, fire, malfunction, or personal injury.

●

Do not expose the device to high humidity or place liquid containers such as a

flower vase on the device to avoid the risk of electrical shock, fire, or

malfunction.

●

Do not expose the device to temperature outside the range 5 – 40 °C (41 – 104

°F) to avoid the risk of fire, deformation of the device panel, or malfunction.

●

Do not expose the device to dusty place to avoid the risk of fire or malfunction.

●

Always follow the owner's manual to set up or connect the devices properly to

avoid the risk of electrical shock, fire, malfunction, or personal injury.

●

If unusual smells, sounds or smoke come from the device, or if foreign objects

such as liquid get into the device, turn off and unplug the computer immediately

to avoid the risk of electrical shock, fire, or malfunction. Contact the store of

purchase or your nearest Yamaha dealer (listed at the back of this manual).

iii

●

Be sure that the computer is electrically grounded to avoid the risk of electrical

shock.

●

Prior to cleaning the drive, always unplug the computer or do not handle the plug

with wet hands to avoid the risk of electrical shock.

CAUTION

Always follow these basic precautions to avoid physical injury to yourself or

others, and damage to the device or other property.

●

Always unplug the computer if it will not be used for a prolonged period of time

or if there is possibility of lightning, to avoid the risk of electrical shock, fire, or

short-circuit.

●

Do not use the device near other electrical appliances such as televisions, radios,

or speakers to avoid the risk of interferences between each other.

●

Do not place the computer unstably to avoid the risk of malfunction or personal

injury by its falling down.

●

Do not place the device with a possibility of excessive vibration to avoid the risk

of damage to written data or malfunction.

●

Place the device horizontally to avoid the risk of damage to written data.

●

Prior to transporting the device, remove the disc from the disc tray to avoid the

risk of damage to written data.

●

Use soft, dry cloths to wipe the device. Do not use benzene, paint thinner,

detergents, or chemically treated wiped cloths, and do not place vinyl, plastic, or

rubber objects on the device to avoid the risk of malfunction or damage to

surface of the device.

●

Do not rest your weight on or place heavy objects on the device, and do not apply

excessive force to the buttons, switches, or connectors to avoid the risk of

damage to the device or personal injury.

●

Do not listen to audio with headphones at high volume for prolonged period of

time to avoid auditory disorder.

●

Prior to turning on the computer, always minimize the volume to avoid auditory disorder

by a sudden burst of sound at high volume.

●

Do not place the device near magnets or anything magnetized such as a display to avoid

the risk of interferences between each other.

●

Have the device serviced regularly to avoid internal dust buildup that can cause

malfunction, damage or fire. For service information and service charges, contact the

store of purchase or your nearest Yamaha dealer (listed at the back of this manual).

●

This drive is for use only with movable equipment, weighing less than 18 kg.

WARRANTY

YAMAHA AND ITS SUPPLIERS ACCEPT NO LIABILITY FOR ANY PROBLEMS THAT OCCUR

AS A RESULT OF ANY OPERATIONS CARRIED OUT OTHER THAN THOSE STATED IN THE

MANUAL THAT COMES WITH THIS PRODUCT, OR THE LOSS OR THE DAMAGE OF ANY

DATA CAUSED AS A RESULT OF USING THIS PRODUCT.

Precautions for Transportation

Transporting the device unfixed may damage its internal mechanism or circuits.

• Remove the disc from the disc tray of the device.

• Put the device in the original box.

Prior to use, check that the complete accessories are included. (Refer to the original box.)

To reduce power consumption of the CRW3200E drive, set your computer to power saving

mode. (P. 36)

This document may not, in whole or in part, be copied, photocopied, reproduced,

translated, transmitted, or reduced to any electronic medium of machine readable form

without prior consent in writing from Yamaha.

Windows is a registered trademark of Microsoft Corporation.

SafeBurn™ is a trademark of Yamaha Corporation.

All other trademarks are the property of their respective companies.

Table of Contents

Features of the CRW3200E Drive .................................................1

Names and Functions of Parts.....................................................2

Front Panel...............................................................................................2

Rear Panel................................................................................................3

Precautions on Use.................................................................. 4

Handling Discs ........................................................................................4

Disclaimer of Indemnity..........................................................................4

Useable discs ...........................................................................................5

System Requirements ..............................................................................7

Preparing the CRW3200E Drive ...................................................8

Serial Number..........................................................................................8

1 Decide the Installation Method............................................................9

2 Set the Jumper Switch .......................................................................14

3 Install the CRW3200E Drive.............................................................16

4 Check Recognition of the CRW3200E Drive....................................22

5 Install CD Writing Software..............................................................25

Loading/Ejecting a Disc ...........................................................26

Troubleshooting.....................................................................28

Firmware.............................................................................34

CRW3200E Drive Specifications .................................................35

Technical Notes.....................................................................38

Buffer Underrun Protection Function....................................................38

Writing Methods....................................................................................38

For details about how to install and use the CD writing software, refer to the

documentation that comes with it.

• The information contained in this manual is subject to change without prior notice.

• Reproduction of this manual, either in part or in full, is expressly forbidden.

Features of the CRW3200E Drive

High speed writing/reading

The CRW3200E drive supports up to 24X-speed writing for CD-R discs, and up

to 10X-speed writing/rewriting for CD-RW discs. In addition, the drive

supports data reading and digital audio data extraction at up to 40X speed.

Tip

• The Partial CAV method permits 24X-speed writing for CD-R discs.

• The CLV method and the 4X – 10X Full CAV method permit 10X-speed writing/

rewriting for CD-RW discs.

SafeBurn™ (Enhanced stability writing technology)

The generous 8MB buffer memory provides sufficient data storage to enable

stable disc writing at high speeds. Even if data transfer from the computer is

interrupted, the Buffer Underrun Protection function is activated to save CD-R

discs from a writing error. (P. 38)

“Optimum Write Speed Control” adjusts the writing speed to the optimum rate

for every CD-R disc automatically. You can set the maximum writing speed

with your CD writing software.

• Optimum Write Speed Control can be activated when the maximum writing

speed is set at 12X or more.

• The minimum writing speed to be automatically selected is 8X. Manually set the

optimum writing speed if a writing speed supported by a disc is less than 8X.

High fidelity digital audio

The CRW3200E drive supports extraction of digital audio data at up to 40X

speed using CD writing software, as well as recording digital audio with high

fidelity even at 24X-speed writing. For higher quality audio, the CRW3200E

drive provides a digital audio output jack which can be connected to the sound

card with an SPDIF (digital audio) input jack, if your computer has one

installed, with an optional digital audio cable.

Audio Master Quality Recording (High quality audio writing mode)

Audio Master Quality Recording enables you to create high quality audio CDs.

This mode is available for CD-R discs with a capacity of 650MB and 700MB.

(P. 40)

Audio CDs that are created with Audio Master Quality Recording may not be

played back on certain audio recorders and CD-R/RW drives.

CD-MRW (CD Mount Rainier ReWriting)

CD-MRW is a new standard of packet writing. Compared to the ordinary packet

writing, CD-MRW provides many useful functions such as background

formatting. (P. 40)

Note

Names and Functions of Parts

➀

Disc tray

Holds the disc. It is opened or closed by

pressing the eject button. (P. 26)

➁

Manual eject hole

Forcibly opens the disc tray when the

tray cannot be opened by pressing the

eject button. (P. 27)

➂

Eject button

Press to open or close the disc tray.

(P. 26)

➃

Headphone jack

Connects headphones or external

speakers to the drive; has stereo mini-

jack specifications.

➄

Headphone volume dial

Controls the volume of the headphones.

The volume increases as the dial is turned

to the right.

➅

LED

Indicates the operational status of the

CRW3200E drive by its colors and

blinking patterns.

Lights or blinks blue

• Lights: Standby (with disc)

• Blinks: Opening/Closing disc tray, or

reading disc information (TOC)

• Blinks rapidly: Playback audio

• Blinks irregularly: Reading data

Lights or blinks purple

• Lights: Standby (no disc) or the disc tray

is open

• Blinks: Accessing for writing or test

writing

• Blinks rapidly: Writing

Blinks orange

• Malfunction

Off

• Power saving (operated via computer

setting)

Front Panel

➅

➁

➃➄

➀➂

Names and Functions of Parts

➀

DIGITAL AUDIO OUT

Connects to the sound card in the

computer if the sound card has an SPDIF

(digital audio) input jack using an

optional digital audio cable. (P. 20)

➁

ANALOG AUDIO OUT

Connects to the sound card in the

computer using the included audio cable.

(P. 19)

➂

Jumper switch

Insert a plastic shunt into the switch to

set the connection of the IDE to master or

slave. The switch is set at slave by

default. (P. 14)

➃

IDE INTERFACE CONNECTOR

Connects the included 40-pin IDE cable.

(P. 17)

➄

DC INPUT

Connects the 4-pin internal power cable

of the computer. (P. 21)

Rear Panel

➁➀➂ ➃ ➄

Precautions on Use

To avoid trouble, such as writing errors, loss of recorded data, and malfunction

of the drive, take the following precautions when handling discs.

• Do not place discs in a hot or damp place or where they will be exposed to

direct sunlight.

• Do not touch the disc surface. Hold the disc by the edge when handling it.

• Remove dust and dirt from the disc surface. Use an air spray to remove dust.

The disc surface may be scratched if strongly wiped with a dry cloth.

• Do not stick labels to the disc surface or write anything on it except where

designated.

• Do not clean discs with chemicals or detergents.

• Do not bend or drop discs.

It is prohibited by law to duplicate copyright material for non-personal use

without the prior consent of the copyright holder. When copying material with

your CD-R/RW drive, take due care not to infringe the copyright.

• Yamaha assumes no liability for the loss of any profits incurred as a result of

the loss or corruption of data written on a CD-R or CD-RW, for any loss or

damage caused by or arising out of extraordinary circumstances (including

circumstances that Yamaha has foreseen or could foresee), nor for any

damages incurred or claimed by a third party.

• After handling important data, make a comparison between the original and

the copied data (to confirm that the data has been copied properly).

• In no event shall Yamaha be liable for any damage to discs due to a Buffer

Underrun Error (P. 38) or for any other reason, or the inability to use

distributed discs with your drive.

• Yamaha assumes no liability for the inability to write/playback discs because

of their format.

Handling Discs

Disclaimer of Indemnity

Precautions on Use

Discs that can be written on

The CRW3200E drive can write on the following discs.

For the latest information about discs previously checked for compatibility with

the drive, refer to the YAMAHA CD-R/RW Drive website URL:

http://www.yamaha.co.jp/english/product/computer/

Useable discs

CD-R discs

• The CRW3200E drive can write at 1X, 2X, 4X, 8X, 12X, 16X or 24X speed.

• CD-R discs can be played back on a CD-ROM drive or a CD player.

• 24X-speed writing is enabled with Partial CAV method. (P. 6)

• Check the writing speeds your disc supports prior to writing.

CD-RW discs

• The CRW3200E drive can write/rewrite at 2X or 4X speed.

• CD-RW discs can be read/played back on a device (e.g. CD-ROM drive)

that supports “CD-RW” discs.

Some discs support only 2X speed.

High Speed CD-RW discs

• The CRW3200E drive can write/rewrite at 4X, 8X or 10X speed.

• High Speed CD-RW discs can be read/played back on a CD-RW drive

that bears the High Speed CD-RW logo or a device (e.g. CD-ROM drive)

that supports “CD-RW” discs.

• When using the packet writing method (P. 40) for writing/rewriting onto High

Speed CD-RW discs, you can select the 4X – 10X Full CAV method. For more

information refer to the documentation that comes with your CD writing

software. (Your CD writing software must support the Full CAV method, as

does the CD Writing software that comes with the CRW3200E drive.)

• The Full CAV method is recommended when opening and editing a file on a

CD-RW disc with an application.

• In order to write, erase, read or play back High Speed CD-RW discs, use a CD-

R/RW drive that bears the High Speed CD-RW logo. When using a CD-ROM

drive to read/play back High Speed CD-RW discs, use a drive that supports

CD-RW discs.

If these discs are used with a CD-R/RW drive not bearing the High Speed CD-

RW logo, the discs may not be recognized, resulting in a computer not

operating properly or other malfunctions occurring.

Refer to the YAMAHA website below prior to attempting to read/play back

these discs on a YAMAHA CD-R/RW drive not bearing the High Speed CD-

RW logo.

URL: http://www.yamaha.co.jp/english/product/computer/

Note

Partial CAV (Constant Angular Velocity)

The CLV (Constant Linear Velocity) method is generally used to write data on a

CD-R disc. In writing using the CLV method, the disc rotation speed is adjusted to

keep the data writing speed (data transfer rate) constant on all parts of the disc.

In contrast, the CAV (Constant Angular Velocity) method exercises control so as to

keep the disc rotation speed constant. Since the CAV method makes it possible to

substantially increase the maximum data transfer rate without straining of the drive,

it is adopted today for most CD-ROM drives.

CD formats define the constant linear density of written data so that the amount of

written data per disc rotation will increase as the writing point moves from the inner

track to the outer track.

With the CAV method, therefore, data is transferred at a higher rate when it is

written on the outer tracks of the disc. To achieve 24X-speed writing, the

CRW3200E drive employs the Partial CAV method, which is a combination of the

CAV method for inner tracks and the CLV method for outer tracks.

The Partial CAV method controls the disc rotation speed so that the CRW3200E

drive starts writing at 18X speed on inner tracks, increasing the speed to 24X as the

read/write head moves outward and holds the speed at 24X on outer tracks.

Tip

The CRW3200E drive supports 8cm discs.

Use only circular discs. Do not use any irregular shaped discs such as heart-shaped

or star-shaped discs to avoid the risk of malfunction.

Note

Precautions on Use

The CRW3200E drive is designed to operate in the following computer

environment. If your computer does not meet these requirements, the

CRW3200E drive may not write at the maximum speed.

Computer (PC/AT compatible)

• CPU: Pentium II-class or higher, 300 MHz or faster

• RAM: 32MB (64MB or more is recommended)

64 MB or more is required (128 MB is recommended) for Windows 2000

Professional, while 128 MB or more is required (256 MB is recommended)

for Windows XP.

• An empty 5 ¼-inch drive bay (for installing the CRW3200E drive as an

additional drive into the computer)

• Hard drive space

Writing data on a CD-R/RW disc requires 50MB to 100MB of free space as a

working area on the hard drive. When writing data on a CD-R/RW disc after

creating an image file, there must be enough free space on the hard drive to

store the image file in addition to the working area (a total of up to 900MB).

However, hard drive space for image files is not required when directly

writing onto a CD-R/RW disc from a hard drive or CD-ROM using the

CRW3200E drive (on-the-fly writing).

Image file

You can collect the data files to be written on a CD-R/RW disc into a single image

file.

The image file is useful for writing the same data onto multiple discs. For details,

refer to the documentation that comes with the CD writing software.

Operating system (OS)

Windows 95 (OSR2 or later), Windows 98, Windows 98 Second Edition,

Windows Me, Windows 2000 Professional, or Windows XP.

CD writing software

The CRW3200E drive requires CD writing software to write onto a CD-R/RW

disc. The CD writing software is included. If using other CD writing software,

be sure that the CD writing software supports the CRW3200E drive.

For details about installing and using the CD writing software, refer to the

documentation that comes with the CD writing software.

System Requirements

Preparing the CRW3200E Drive

Preparing tools

• Phillips screwdriver: Use the proper screwdriver

for the screws to install the CRW3200E drive into

the computer.

• Narrow pliers: Insert and remove the included

plastic shunt for the jumper switch.

The serial number is printed on the label on the top of your CRW3200E drive.

When you have a question about the drive, or need user support services, the

serial number is required.

Please write the serial number down in the space below prior to installing the

CRW3200E drive into your computer. It will be difficult to check the serial

number after installation.

Serial Number

Serial number

(10 characters: 3 letters +

7 numbers)

Preparing the CRW3200E Drive

The following describes how to install the CRW3200E drive on the computer

by taking a tower-type computer for example.

The methods of removing the computer cover or panels and installing an internal

device vary depending on the computer model. Refer to the documentation that

comes with the computer.

Check the connection of any IDE device installed to decide the installation

method of the CRW3200E drive.

• The CRW3200E drive supports Ultra ATA/33. Even if the motherboard and the

hard drive support Ultra ATA/66 or Ultra ATA/100, they are operated by Ultra

ATA/33 as long as they are connected to the CRW3200E drive by the same IDE

cable or the included 40-pin IDE cable.

• Install the CRW3200E drive horizontally.

Turn off and unplug the computer.

While the computer is turned on, it is dangerous to handle the internal

computer devices due to the risk of an electrical shock. There is also a risk

of damaging the CRW3200E drive, the computer, etc. Be sure to unplug

the computer prior to handling any internal computer device.

Remove all peripheral devices and cables connected to the

computer prior to removing the computer cover.

Clothes and body can become charged with static electricity.

Discharge any static electricity by touching a metallic part of the case or

power unit.

For more information, refer to the documentation that comes with the

computer.

Note

1 Decide the Installation Method

Note

Installing the CRW3200E drive as an additional drive

Check the IDE channel (primary/secondary and master/slave) connecting the

CRW3200E drive. (P. 12 – 13)

An empty 5 ¼-inch drive bay is required to install the CRW3200E drive.

Replacing an existing IDE device with the CRW3200E drive

Connect the CRW3200E drive to the cable that was previously connected to the

existing IDE device.

When replacing a SCSI device, such as a SCSI type CD-ROM drive, do not connect

the CRW3200E drive to the cable that was previously connected to that SCSI

device. Use the included 40-pin IDE cable to connect the CRW3200E drive to the

computer.

Note

CRW3200E

CD-ROM drive, etc.

Preparing the CRW3200E Drive

Examples of connecting the CRW3200E drive

The following describes how to connect the CRW3200E drive for example

recommended by Yamaha.

Example 1: As a secondary slave (For additional drive)

Example 2: As a secondary master (For replacing the existing drive with the

CRW3200E drive)

For the best performance of the CRW3200E drive, Yamaha recommends

that the drive be connected as the sole secondary master.

CD-ROM drive,

etc. (master)

CRW3200E

drive (slave)

IDE cable (primary) IDE cable (secondary)

Hard drive (master)

CRW3200E

drive (master)

Hard drive (master)

IDE cable (primary) IDE cable (secondary)

• The CRW3200E drive is set at slave by default. If you connect the drive as the

sole secondary master, set the drive to master.

• If you connect an IDE device solely to an IDE cable, set the device to master and

connect the drive to the end of the cable.

• If you start up the operating system from a SCSI hard drive, etc., there may be no

IDE device connected to the primary. In such a case, Yamaha recommends that

the CRW3200E drive be connected as the primary master.

• You may find that the IDE cable has one connector when you try to connect the

removed device to another connector. In such a case, you are required to prepare

an IDE cable with two connectors.

• You may have to change the master/slave setting to connect the removed device

to another connector. For more details, refer to the documentation that comes

with the device or refer to the manufacturer’s website.

E-IDE

E-IDE (Enhanced-IDE) is a standard for connecting computers to IDE devices such

as hard discs, CD-ROMs and CD-R/RW drives. Most computers have two IDE

connectors (primary and secondary). Each connector can be connected to two

devices with an IDE cable.

Two IDE devices connected by one IDE cable are called “master” and “slave.”

Note

Slave

Master

Slave

MasterMotherboard Primary

Secondary

Continued on next page

La pagina sta caricando ...

Yamaha CRW3200E Manuale utente

Marca: Yamaha

Modello: CRW3200E

Categoria: Unità disco ottico

Tipo: Manuale utente

Questo manuale è adatto anche per

Scarica il pdf

rapporto

in altre lingue

English: Yamaha CRW3200E User manual
français: Yamaha CRW3200E Manuel utilisateur
Deutsch: Yamaha CRW3200E Benutzerhandbuch
Nederlands: Yamaha CRW3200E Handleiding
dansk: Yamaha CRW3200E Brugermanual
svenska: Yamaha CRW3200E Användarmanual
Türkçe: Yamaha CRW3200E Kullanım kılavuzu
suomi: Yamaha CRW3200E Ohjekirja
română: Yamaha CRW3200E Manual de utilizare

Yamaha CRW3200E Manuale utente

Questo manuale è adatto anche per

Yamaha CRW3200E Manuale utente

in altre lingue

Documenti correlati

Altri documenti