Genius COMPAS 24 24C Istruzioni per l'uso

Categoria
Gate Opener
Tipo
Istruzioni per l'uso
COMPAS 24
COMPAS 24 C
GUIdA Per l’InStAllAtOre - GUIde fOr the InStAller
GUIde POUr l’InStAllAteUr - GUíA PArA el InStAlAdOr
leItfAden für den InStAllAteUr - GIdS vOOr de InStAllAteUr
ITALIANO
AVVERTENZE PER L’INSTALLATORE
OBBLIGHI GENERALI PER LA SICUREZZA
ATTENZIONE! È importante per la sicurezza delle persone seguire attentamente tutta
l’istruzione. Una errata installazione o un errato uso del prodotto può portare a
gravi danni alle persone.
Leggere attentamente le istruzioni prima di iniziare l’installazione del prodotto.
I materiali dell’imballaggio (plastica, polistirolo, ecc.) non devono essere lasciati alla
portata dei bambini in quanto potenziali fonti di pericolo.
Conservare le istruzioni per riferimenti futuri.
Questo prodotto è stato progettato e costruito esclusivamente per l’utilizzo indicato in
questa documentazione. Qualsiasi altro utilizzo non espressamente indicato potrebbe
pregiudicare l’integrità del prodotto e/o rappresentare fonte di pericolo.
GENIUS declina qualsiasi responsabilità derivata dall’uso improprio o diverso da quello
per cui l’automatismo è destinato.
Non installare l’apparecchio in atmosfera esplosiva: la presenza di gas o fumi infiam-
mabili costituisce un grave pericolo per la sicurezza.
Gli elementi costruttivi meccanici devono essere in accordo con quanto stabilito dalle
Norme EN 12604 e EN 12605.
Per i Paesi extra-CEE, oltre ai riferimenti normativi nazionali, per ottenere un livello di
sicurezza adeguato, devono essere seguite le Norme sopra riportate.
GENIUS non è responsabile dell’inosservanza della Buona Tecnica nella costruzione
delle chiusure da motorizzare, nonché delle deformazioni che dovessero intervenire
nell’utilizzo.
L’installazione deve essere effettuata nell’osservanza delle Norme EN 12453 e EN 12445.
Il livello di sicurezza dell’automazione deve essere C+D.
Prima di effettuare qualsiasi intervento sull’impianto, togliere l’alimentazione elettrica
e scollegare le batterie.
Prevedere sulla rete di alimentazione dell’automazione un interruttore onnipolare con
distanza d’apertura dei contatti uguale o superiore a 3 mm. È consigliabile l’uso di un
magnetotermico da 6A con interruzione onnipolare.
Verificare che a monte dell’impianto vi sia un interruttore differenziale con soglia da
0,03 A.
Verificare che l’impianto di terra sia realizzato a regola d’arte e collegarvi le parti
metalliche della chiusura.
L’automazione dispone di una sicurezza intrinseca antischiacciamento costituita da un
controllo di coppia. E’ comunque necessario verificarne la sogli di intervento secondo
quanto previsto dalle Norme indicate al punto 10.
I dispositivi di sicurezza (norma EN 12978) permettono di proteggere eventuali aree
di pericolo da Rischi meccanici di movimento, come ad Es. schiacciamento, convo-
gliamento, cesoiamento.
Per ogni impianto è consigliato l’utilizzo di almeno una segnalazione luminosa nonché
di un cartello di segnalazione fissato adeguatamente sulla struttura dell’infisso, oltre
ai dispositivi citati al punto “16”.
GENIUS declina ogni responsabilità ai fini della sicurezza e del buon funzionamento
dell’automazione, in caso vengano utilizzati componenti dell’impianto non di pro-
duzione GENIUS.
Per la manutenzione utilizzare esclusivamente parti originali GENIUS.
Non eseguire alcuna modifica sui componenti facenti parte del sistema d’automa-
zione.
L’installatore deve fornire tutte le informazioni relative al funzionamento manuale
del sistema in caso di emergenza e consegnare all’Utente utilizzatore dell’impianto il
libretto d’avvertenze allegato al prodotto.
Non permettere ai bambini o persone di sostare nelle vicinanze del prodotto durante
il funzionamento.
L’applicazione non può essere utilizzata da bambini, da persone con ridotte ca-
pacità fisiche, mentali, sensoriali o da persone prive di esperienza o del necessario
addestramento.
Tenere fuori dalla portata dei bambini radiocomandi o qualsiasi altro datore di impulso,
per evitare che l’automazione possa essere azionata involontariamente.
Il transito tra le ante deve avvenire solo a cancello completamente aperto.
L’utente utilizzatore deve astenersi da qualsiasi tentativo di riparazione o d’intervento
e deve rivolgersi solo ed esclusivamente a personale qualificato GENIUS o centri
d’assistenza GENIUS.
Tutto quello che non è previsto espressamente in queste istruzioni non è permesso.
ENGLISH
IMPORTANT NOTICE FOR THE INSTALLER
GENERAL SAFETY REGULATIONS
ATTENTION! To ensure the safety of people, it is important that you read all the fol-
lowing instructions. Incorrect installation or incorrect use of the product could
cause serious harm to people.
Carefully read the instructions before beginning to install the product.
Do not leave packing materials (plastic, polystyrene, etc.) within reach of children
as such materials are potential sources of danger.
Store these instructions for future reference.
This product was designed and built strictly for the use indicated in this documentation.
Any other use, not expressly indicated here, could compromise the good condition/
operation of the product and/or be a source of danger.
GENIUS declines all liability caused by improper use or use other than that for which
the automated system was intended.
Do not install the equipment in an explosive atmosphere: the presence of inflammable
gas or fumes is a serious danger to safety.
The mechanical parts must conform to the provisions of Standards EN 12604 and EN
12605.
For non-EU countries, to obtain an adequate level of safety, the Standards mentioned
above must be observed, in addition to national legal regulations.
GENIUS is not responsible for failure to observe Good Technique in the construction
of the closing elements to be motorised, or for any deformation that may occur
during use.
The installation must conform to Standards EN 12453 and EN 12445. The safety level of
the automated system must be C+D.
Before attempting any job on the system, cut out electrical power and disconnect
the batteries.
The mains power supply of the automated system must be fitted with an all-pole
switch with contact opening distance of 3mm or greater. Use of a 6A thermal breaker
with all-pole circuit break is recommended.
Make sure that a differential switch with threshold of 0.03 A is fitted upstream of the
system.
Make sure that the earthing system is perfectly constructed, and connect metal parts
of the means of the closure to it.
The automated system is supplied with an intrinsic anti-crushing safety device consisting
of a torque control. Nevertheless, its tripping threshold must be checked as specified
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
in the Standards indicated at point 10.
The safety devices (EN 12978 standard) protect any danger areas against mechanical
movement Risks, such as crushing, dragging, and shearing.
Use of at least one indicator-light is recommended for every system, as well as a
warning sign adequately secured to the frame structure, in addition to the devices
mentioned at point “16”.
GENIUS declines all liability as concerns safety and efficient operation of the automated
system, if system components not produced by GENIUS are used.
For maintenance, strictly use original parts by GENIUS.
Do not in any way modify the components of the automated system.
The installer shall supply all information concerning manual operation of the system
in case of an emergency, and shall hand over to the user the warnings handbook
supplied with the product.
Do not allow children or adults to stay near the product while it is operating.
The application cannot be used by children, by people with reduced physical, mental,
sensorial capacity, or by people without experience or the necessary training.
Keep remote controls or other pulse generators away from children, to prevent the
automated system from being activated involuntarily.
Transit through the leaves is allowed only when the gate is fully open.
The User must not in any way attempt to repair or to take direct action and must solely
contact qualified GENIUS personnel or GENIUS service centres.
Anything not expressly specified in these instructions is not permitted.
FRANÇAIS
CONSIGNES POUR L’INSTALLATEUR
RÈGLES DE SÉCURITÉ
ATTENTION! Il est important, pour la sécurité des personnes, de suivre à la lettre
toutes les instructions. Une installation erronée ou un usage erroné du produit
peut entraîner de graves conséquences pour les personnes.
Lire attentivement les instructions avant d’installer le produit.
Les matériaux d’emballage (matière plastique, polystyrène, etc.) ne doivent pas être
laissés à la portée des enfants car ils constituent des sources potentielles de danger.
Conserver les instructions pour les références futures.
Ce produit a été conçu et construit exclusivement pour l’usage indiqué dans cette
documentation. Toute autre utilisation non expressément indiquée pourrait compro-
mettre l’intégrité du produit et/ou représenter une source de danger.
GENIUS décline toute responsabilité qui dériverait d’usage impropre ou différent de
celui auquel l’automatisme est destiné.
Ne pas installer l’appareil dans une atmosphère explosive: la présence de gaz ou de
fumées inflammables constitue un grave danger pour la sécurité.
Les composants mécaniques doivent pondre aux prescriptions des Normes EN
12604 et EN 12605.
Pour les Pays extra-CEE, l’obtention d’un niveau de sécurité approprié exige non
seulement le respect des normes nationales, mais également le respect des Normes
susmentionnées.
GENIUS n’est pas responsable du non-respect de la Bonne Technique dans la con-
struction des fermetures à motoriser, ni des déformations qui pourraient intervenir lors
de l’utilisation.
L’installation doit être effectuée conformément aux Normes EN 12453 et EN 12445. Le
niveau de sécurité de l’automatisme doit être C+D.
Couper l’alimentation électrique et déconnecter la batterie avant toute intervention
sur l’installation.
Prévoir, sur le secteur d’alimentation de l’automatisme, un interrupteur omnipolaire
avec une distance d’ouverture des contacts égale ou supérieure à 3 mm. On recom-
mande d’utiliser un magnétothermique de 6A avec interruption omnipolaire.
Vérifier qu’il y ait, en amont de l’installation, un interrupteur différentiel avec un seuil
de 0,03 A.
Vérifier que la mise à terre est réalisée selon les règles de l’art et y connecter les pièces
métalliques de la fermeture.
L’automatisme dispose d’une sécurité intrinsèque anti-écrasement, formée d’un con-
trôle du couple. Il est toutefois nécessaire d’en vérifier le seuil d’intervention suivant les
prescriptions des Normes indiquées au point 10.
Les dispositifs de sécurité (norme EN 12978) permettent de protéger des zones éven-
tuellement dangereuses contre les Risques mécaniques du mouvement, comme
l’écrasement, l’acheminement, le cisaillement.
On recommande que toute installation soit doté au moins d’une signalisation lumi-
neuse, d’un panneau de signalisation fixé, de manière appropriée, sur la structure de
la fermeture, ainsi que des dispositifs cités au point “16”.
GENIUS décline toute responsabilité quant à la sécurité et au bon fonctionnement
de l’automatisme si les composants utilisés dans l’installation n’appartiennent pas à
la production GENIUS.
Utiliser exclusivement, pour l’entretien, des pièces GENIUS originales.
Ne jamais modifier les composants faisant partie du système d’automatisme.
L’installateur doit fournir toutes les informations relatives au fonctionnement manuel du
système en cas d’urgence et remettre à l’Usager qui utilise l’installation les “Instructions
pour l’Usager” fournies avec le produit.
Interdire aux enfants ou aux tiers de stationner près du produit durant le fonction-
nement.
Ne pas permettre aux enfants, aux personennes ayant des capacités physiques,
mentales et sensorielles limitées ou dépourvues de l’expérience ou de la formation
nécessaires d’utiliser l’application en question.
Eloigner de la portée des enfants les radiocommandes ou tout autre générateur
d’impulsions, pour éviter tout actionnement involontaire de l’automatisme.
Le transit entre les vantaux ne doit avoir lieu que lorsque le portail est complètement
ouvert.
L’utilisateur doit s’abstenir de toute tentative de réparation ou d’intervention et doit
s’adresser uniquement et exclusivement au personnel qualifié GENIUS ou aux centres
d’assistance GENIUS.
Tout ce qui n’est pas prévu expressément dans ces instructions est interdit.
ESPAÑOL
ADVERTENCIAS PARA EL INSTALADOR
REGLAS GENERALES PARA LA SEGURIDAD
ATENCION! Es sumamente importante para la seguridad de las personas seguir
atentamente las presentes instrucciones. Una instalación incorrecta o un uso
impropio del producto puede causar graves daños a las personas.
Lean detenidamente las instrucciones antes de instalar el producto.
Los materiales del embalaje (plástico, poliestireno, etc.) no deben dejarse al alcance
de los niños, ya que constituyen fuentes potenciales de peligro.
Guarden las instrucciones para futuras consultas.
Este producto ha sido proyectado y fabricado exclusivamente para la utilización
indicada en el presente manual. Cualquier uso diverso del previsto podría perjudicar
el funcionamiento del producto y/o representar fuente de peligro.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
1.
2.
3.
4.
GENIUS declina cualquier responsabilidad derivada de un uso impropio o diverso
del previsto.
No instalen el aparato en atmósfera explosiva: la presencia de gas o humos inflama-
bles constituye un grave peligro para la seguridad.
Los elementos constructivos mecánicos deben estar de acuerdo con lo establecido
en las Normas EN 12604 y EN 12605.
Para los países no pertenecientes a la CEE, además de las referencias normativas
nacionales, para obtener un nivel de seguridad adecuado, deben seguirse las
Normas arriba indicadas.
GENIUS no es responsable del incumplimiento de las buenas técnicas de fabricación
de los cierres que se han de motorizar, así como de las deformaciones que pudieran
intervenir en la utilización.
La instalación debe ser realizada de conformidad con las Normas EN 12453 y EN
12445. El nivel de seguridad de la automación debe ser C+D.
Quiten la alimentación eléctrica y desconecten las baterías antes de efectuar
cualquier intervención en la instalación.
Coloquen en la red de alimentación de la automación un interruptor omnipolar con
distancia de apertura de los contactos igual o superior a 3 mm. Se aconseja usar un
magnetotérmico de 6A con interrupción omnipolar.
Comprueben que la instalación disponga línea arriba de un interruptor diferencial
con umbral de 0,03 A.
Verifiquen que la instalación de tierra esté correctamente realizada y conecten las
partes metálicas del cierre.
La automación dispone de un dispositivo de seguridad antiaplastamiento constituido
por un control de par. No obstante, es necesario comprobar el umbral de intervención
según lo previsto en las Normas indicadas en el punto 10.
Los dispositivos de seguridad (norma EN 12978) permiten proteger posibles áreas
de peligro de Riesgos mecánicos de movimiento, como por ej. aplastamiento,
arrastre, corte.
Para cada equipo se aconseja usar por lo menos una señalización luminosa así
como un cartel de señalización adecuadamente fijado a la estructura del bastidor,
además de los dispositivos indicados en el “16”.
GENIUS declina toda responsabilidad relativa a la seguridad y al buen funciona-
miento de la automación si se utilizan componentes de la instalación que no sean
de producción GENIUS.
Para el mantenimiento utilicen exclusivamente piezas originales GENIUS
No efectúen ninguna modificación en los componentes que forman parte del
sistema de automación.
El instalador debe proporcionar todas las informaciones relativas al funcionamiento
del sistema en caso de emergencia y entregar al usuario del equipo el manual de
advertencias que se adjunta al producto.
No permitan que niños o personas se detengan en proximidad del producto durante
su funcionamiento.
La aplicación no puede ser utilizada por niños, personas con reducida capacidad
física, mental, sensorial o personas sin experiencia o la necesaria formación.
Mantengan lejos del alcance los niños los telemandos o cualquier otro emisor de
impulso, para evitar que la automación pueda ser accionada involuntariamente.
Sólo puede transitarse entre las hojas si la cancela está completamente abierta.
El usuario debe abstenerse de intentar reparar o de intervenir directamente, y debe
dirigirse exclusivamente a personal cualificado GENIUS o a centros de asistencia
GENIUS.
Todo lo que no esté previsto expresamente en las presentes instrucciones debe
entenderse como no permitido
DEUTSCH
HINWEISE FÜR DEN INSTALLATIONSTECHNIKER
ALLGEMEINE SICHERHEITSVORSCHRIFTEN
ACHTUNG! Um die Sicherheit von Personen zu gewährleisten, sollte die Anleitung auf-
merksam befolgt werden. Eine falsche Installation oder ein fehlerhafter Betrieb
des Produktes können zu schwerwiegenden Personenschäden führen.
Bevor mit der Installation des Produktes begonnen wird, sollten die Anleitungen
aufmerksam gelesen werden.
Das Verpackungsmaterial (Kunststoff, Styropor, usw.) sollte nicht in Reichweite von
Kindern aufbewahrt werden, da es eine potentielle Gefahrenquelle darstellt.
Die Anleitung sollte aufbewahrt werden, um auch in Zukunft Bezug auf sie nehmen
zu können.
Dieses Produkt wurde ausschließlich für den in diesen Unterlagen angegebenen Ge-
brauch entwickelt und hergestellt. Jeder andere Gebrauch, der nicht ausdrücklich
angegeben ist, könnte die Unversehrtheit des Produktes beeinträchtigen und/oder
eine Gefahrenquelle darstellen.
Die Firma GENIUS lehnt jede Haftung für Schäden, die durch unsachgemäßen oder
nicht bestimmungsgemäßen Gebrauch der Automatik verursacht werden, ab.
Das Gerät sollte nicht in explosionsgefährdeten Umgebungen installiert werden: das
Vorhandensein von entflammbaren Gasen oder Rauch stellt ein schwerwiegendes
Sicherheitsrisiko dar.
Die mechanischen Bauelemente müssen den Anforderungen der Normen EN 12604
und EN 12605 entsprechen.
Für Länder, die nicht der Europäischen Union angehören, sind für die Gewährleistung
eines entsprechenden Sicherheitsniveaus neben den nationalen gesetzlichen Bezug-
svorschriften die oben aufgeführten Normen zu beachten.
Die Firma GENIUS übernimmt keine Haftung im Falle von nicht fachgerechten Au-
sführungen bei der Herstellung der anzutreibenden Schließvorrichtungen sowie bei
Deformationen, die eventuell beim Betrieb entstehen.
Die Installation muß unter Beachtung der Normen EN 12453 und EN 12445 erfolgen.
Die Sicherheitsstufe der Automatik sollte C+D sein.
Vor der Ausführung jeglicher Eingriffe auf der Anlage sind die elektrische Versorgung
und die Batterie abzunehmen.
Auf dem Versorgungsnetz der Automatik ist ein omnipolarer Schalter mit Öffnun-
gsabstand der Kontakte von über oder gleich 3 mm einzubauen. Darüber hinaus
wird der Einsatz eines Magnetschutzschalters mit 6A mit omnipolarer Abschaltung
empfohlen.
Es sollte überprüft werden, ob vor der Anlage ein Differentialschalter mit einer Auslö-
seschwelle von 0,03 A zwischengeschaltet ist.
Es sollte überprüft werden, ob die Erdungsanlage fachgerecht augeführt wurde. Die
Metallteile der Schließung sollten an diese Anlage angeschlossen werden.
Die Automation verfügt über eine eingebaute Sicherheitsvorrichtung für den Quetsch-
schutz, die aus einer Drehmomentkontrolle besteht. Es ist in jedem Falle erforderlich,
deren Eingriffsschwelle gemäß der Vorgaben der unter Punkt 10 angegebenen
Vorschriften zu überprüfen.
Die Sicherheitsvorrichtungen (Norm EN 12978) ermöglichen den Schutz eventueller
Gefahrenbereiche vor mechanischen Bewegungsrisiken, wie zum Beispiel Quetschun-
gen, Mitschleifen oder Schnittverletzungen.
Für jede Anlage wird der Einsatz von mindestens einem Leuchtsignal empfohlen
sowie eines Hinweisschildes, das über eine entsprechende Befestigung mit dem
Aufbau des Tors verbunden wird. Darüber hinaus sind die unter Punkt “16” erwähnten
Vorrichtungen einzusetzen.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
Die Firma GENIUS lehnt jede Haftung hinsichtlich der Sicherheit und des störungsfreien
Betriebs der Automatik ab, soweit Komponenten auf der Anlage eingesetzt werden,
die nicht im Hause GENIUS hergestellt urden.
Bei der Instandhaltung sollten ausschließlich Originalteile der Firma GENIUS verwendet
werden.
Auf den Komponenten, die Teil des Automationssystems sind, sollten keine Verände-
rungen vorgenommen werden.
Der Installateur sollte alle Informationen hinsichtlich des manuellen Betriebs des
Systems in Notfällen liefern und dem Betreiber der Anlage das Anleitungsbuch, das
dem Produkt beigelegt ist, übergeben.
Weder Kinder noch Erwachsene sollten sich während des Betriebs in der unmittelbaren
Nähe der Automation aufhalten.
Die Anwendung darf nicht von Kindern, von Personen mit verminderter körperlicher,
geistiger, sensorieller Fähigkeit oder Personen ohne Erfahrungen oder der erforderlichen
Ausbildung verwendet werden.
Die Funksteuerungen und alle anderen Impulsgeber sollten außerhalb der Reichweite
von Kindern aufbewahrt werden, um ein versehentliches Aktivieren der Automation
zu vermeiden.
Der Durchgang oder die Durchfahrt zwischen den Flügeln darf lediglich bei vollständig
geöffnetem Tor erfolgen.
Der Benutzer darf direkt keine Versuche für Reparaturen oder Arbeiten vornehmen
und hat sich ausschließlich an qualifiziertes Fachpersonal GENIUS oder an Kunden-
dienstzentren GENIUS zu wenden.
Alle Vorgehensweisen, die nicht ausdrücklich in der vorliegenden Anleitung vorge-
sehen sind, sind nicht zulässig
NEDERLANDS
WAARSCHUWINGEN VOOR DE INSTALLATEUR
ALGEMENE VEILIGHEIDSVOORSCHRIFTEN
LET OP! Het is belangrijk voor de veiligheid dat deze hele instructie zorgvuldig wordt
opgevolgd. Een onjuiste installatie of foutief gebruik van het product kunnen
ernstig persoonlijk letsel veroorzaken.
Lees de instructies aandachtig door alvorens te beginnen met de installatie van
het product.
De verpakkingsmaterialen (plastic, polystyreen, enz.) mogen niet binnen het bereik
van kinderen worden gelaten, want zij vormen een mogelijke bron van gevaar.
Bewaar de instructies voor raadpleging in de toekomst.
Dit product is uitsluitend ontworpen en gebouwd voor het doel dat in deze documen-
tatie wordt aangegeven. Elk ander gebruik, dat niet uitdrukkelijk wordt vermeld, zou
het product kunnen beschadigen en/of een bron van gevaar kunnen vormen.
GENIUS aanvaardt geen enkele aansprakelijkheid voor schade die ontstaat uit
oneigenlijk gebruik of ander gebruik dan waarvoor het automatische systeem is
bedoeld.
Installeer het apparaat niet in een explosiegevaarlijke omgeving: de aanwezigheid
van ontvlambare gassen of dampen vormt een ernstig gevaar voor de veiligheid.
De mechanische bouwelementen moeten in overeenstemming zijn met de bepalin-
gen van de normen EN 12604 en EN 12605.
Voor niet-EEG landen moeten, om een goed veiligheidsniveau te bereiken, behalve de
nationale voorschriften ook de bovenstaande normen in acht worden genomen.
GENIUS is niet aansprakelijk als de regels der goede techniek niet in acht genomen
zijn bij de bouw van het sluitwerk dat gemotoriseerd moet worden, noch voor ver-
vormingen die zouden kunnen ontstaan bij het gebruik.
De installatie dient te geschieden in overeenstemming met de normen EN 12453 en
EN 12445. Het veiligheidsniveau van het automatische systeem moet C+D zijn.
Alvorens ingrepen te gaan verrichten op de installatie moet de elektrische voeding
worden weggenomen en moeten de batterijen worden afgekoppeld.
Zorg op het voedingsnet van het automatische systeem voor een meerpolige
schakelaar met een opening tussen de contacten van 3 mm of meer. Het wordt
geadviseerd een magnetothermische schakelaar van 6A te gebruiken met meerpo-
lige onderbreking.
Controleer of er bovenstrooms van de installatie een differentieelschakelaar is ge-
plaatst met een limiet van 0,03 A.
Controleer of de aardingsinstallatie vakkundig is aangelegd en sluit er de metalen
delen van het sluitsysteem op aan.
Het automatische systeem beschikt over een intrinsieke beveiliging tegen inklem-
ming, bestaande uit een controle van het koppel. De inschakellimiet hiervan dient
echter te worden gecontroleerd volgens de bepalingen van de normen die worden
vermeld onder punt 10.
De veiligheidsvoorzieningen (norm EN 12978) maken het mogelijk eventuele gevaar-
lijke gebieden te beschermen tegen Mechanische gevaren door beweging, zoals
bijvoorbeeld inklemming, meesleuren of amputatie.
Het wordt voor elke installatie geadviseerd minstens één lichtsignaal te gebruiken
alsook een waarschuwingsbord dat goed op de constructie van het hang- en slui-
twerk dient te worden bevestigd, afgezien nog van de voorzieningen die genoemd
zijn onder punt “16”.
GENIUS aanvaardt geen enkele aansprakelijkheid voor wat betreft de veiligheid en de
goede werking van het automatische systeem, als er in de installatie gebruik gemaakt
wordt van componenten die niet door GENIUS zijn geproduceerd.
Gebruik voor het onderhoud uitsluitend originele GENIUS-onderdelen.
Verricht geen wijzigingen op componenten die deel uitmaken van het automatische
systeem.
De installateur dient alle informatie te verstrekken over de handbediening van het
systeem in noodgevallen, en moet de gebruiker van de installatie het bij het product
geleverde boekje met aanwijzingen overhandigen.
De toepassing mag niet worden gebruikt door kinderen, personen met lichamelijke,
geestelijke en sensoriele beperkingen, of door personen zonder ervaring of de be-
nodigde training.
Sta het niet toe dat kinderen of volwassenen zich ophouden in de buurt van het
product terwijl dit in werking is.
Houd radio-afstandsbedieningen of alle andere impulsgevers buiten het bereik van
kinderen, om te voorkomen dat het automatische systeem onopzettelijk kan worden
aangedreven.
Ga alleen tussen de vleugels door als het hek helemaal geopend is.
De gebruiker mag zelf geen pogingen ondernemen tot reparaties of andere directe
ingrepen, en dient zich uitsluitend te wenden tot gekwalificeerd en geautoriseerd
GENIUS-personeel of een erkend GENIUS-servicecentrum.
Alles wat niet uitdrukkelijk in deze instructies wordt aangegeven, is niet toegestaan
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
COMPAS 24 - COMPAS 24C
ENGLISH
Guide for the installer
Page 5
Notes on reading the instruction
Read this installation manual to the full before you begin installing the product.
The symbol indicates notes that are important for the safety of persons and for the good condition of the automated system.
The symbol draws your attention to the notes on the characteristics and operation of the product.
CE DECLARATION OF CONFORMITY
Manufacturer: GENIUS S.p.A.
Address: Via Padre Elzi, 32 - 24050 - Grassobbio- Bergamo - ITALY
Declares that: Operator mod. COMPAS 24 - COMPAS 24 CCOMPAS 24 - COMPAS 24 C powered on 230V~
is built to be integrated into a machine or to be assembled with other machinery to create a machine under the provisions of Directive
2006/42/EC;
conforms to the essential safety requirements of the following EEC directives:
2006/95/EC Low Voltage directive.
2004/108/EC Electromagnetic Compatibility directive.
and also declares that it is prohibited to put into service the machinery until the machine in which it will be integrated or of which it will
become a component has been identified and declared as conforming to the conditions of Directive 2006/42/EEC and subsequent
modifications.
Grassobbio, December 30, 2009
Managing Director
D. Gianantoni
INDEX
IMPORTANT WARNINGS FOR THE INSTALLER page.6
1. COMPONENTS (Fig. 1) page.6
2. TECHNICAL SPECIFICATIONS page.6
3. ELECTRICAL CONNECTIONS (Fig. 4) page.6
4. INSTALLATION page.6
4.1. PRELIMINARY CHECKS page.6
4.2 INSTALLATION DIMENSIONS page.6
4.3. INSTALLING THE OPERATOR page.7
4.4. WIRING THE OPERATOR page.7
4.5. POSITIONING THE MECHANICAL STOPS page.7
5. AUTOMATED SYSTEM TEST page.7
6. MANUAL MODE OPERATION page.7
7. SPECIAL APPLICATIONS page.8
8. MAINTENANCE page.8
9. REPAIRS page.8
10. ACCESSORIES page.8
COMPAS 24 - COMPAS 24C
ENGLISH
Guide for the installer
Page 6
Thank you for choosing our product. GENIUS is sure you will get
the performances you expect to satisfy your requirements. All our
products are the result of a many years’ experience in the field of
the automated systems, strengthened by being part of a world
leading group in this sector.
In the middle of the manual you will find a detachable
booklet containing all the images for the installation.
The COMPAS automated system consists of a non-reversing electro-
mechanical operator available in two versions:
• COMPAS 24C with built-in control unit
• COMPAS 24 without control unit
The operator was designed for automating the opening of gates
with one or two leaves, with maximum length of 2.5m.
A handy, safe releases system, with personalised key, moves the
leaf in case of a power cut or fault.
The two articulated arms are designed for moving gates with very
large pilasters. The distance between the hinge and the gear-
motor securing point can be up to 220 mm. Thanks to the special
geometry of the two arms, all possible shearing points have been
eliminated.
IMPORTANT WARNINGS FOR THE INSTALLER
Carefully read the whole manual before beginning to install the
operator.
Store the manual for future reference.
The correct operation and the declared technical specifications
are only valid if the instructions given in this manual are strictly
observed and only GENIUS accessories as well as safety device
are used.
To guarantee an adequate level of safety of the automated
system, the use of a control unit with an adjustable electronic
clutch is necessary due to the lack of a mechanical clutch .
The automated system was designed and built to control vehicle
access. Avoid any other use.
The operator cannot be used to move safety exits or gates
installed on emergency routes (escape routes).
Do not transit when the rod is moving.
Anything not expressly specified in this manual is not permitted.
1. COMPONENTS (Fig. 1)
Pos. Description
a
Gearmotor
b
Transformer
c
Control unit (for master motor only)
d
Release device
e
Receiver module (optional)
f
Mechanical stops
g
Transmission arm
h
Covering housing
i
Rear bracket
j
Lower housing
2. TECHNICAL SPECIFICATIONS
Model Compas 24C Compas
Power supply 230 V~ /
Electric motor 24 V
Absorbed power 120 W 40 W
Max torque 250 N/m
Nominal torque 165 N/m
Max angular speed 13 °/sec
Max leaf
a b
2.5 m
Max leaf weight.
b
See graph fig. 2
Use frequency at 20°C 80 cycles/day
Consecutive cycles at 20°C 30
Mximum continuous operating time O.T. 17 min.
Protection Class IP44
Operating ambient temperature
-20°C +55°C
Noise level <70 dB (A)
Operator weight 8.7 Kg 7 Kg
Dimensions See fig. 3
a For leaves with a length L>2m, an electric lock must be installed
to guarantee locking the leaf.
b The weight P of the leaf is a function of the length L. Check if your
leaf is in the zone shown in the graph of fig. 2.
3. ELECTRICAL CONNECTIONS (Fig. 4)
Pos. Description Cables section
a
Gearmotor COMPAS 24 C 3x2.5 mm
2
b Gearmotor COMPAS 24
a
2x2.5 mm
2
c
Flashing lamp 2x1.5 mm
2
d
Key-operated selector switch 2x0.5 mm
2
e
Photocell transmitter 2x0.5 mm
2
(BUS)
f
Photocell receiver 2x0.5 mm
2
(BUS)
g Electric lock
b
2x1 mm
2
a Only for two leaf applications.
b Obligatory for leaf L>2m.
The lay-out below refers to an installation with two motors,
with all safety and signalling devices connected.
For two-motor applications, use a cable, type H05RN-F to
connect the MASTER and SLAVE operators.
4. INSTALLATION
4.1. PRELIMINARY CHECKS
To ensure a correctly operating automated system, the structure of
the gate to be moved must satisfy the following requirements:
The mechanical construction elements must comply with the
provisions of the EN12604 and EN 12605 standards.
leaf length must conform to the operator characteristics (see
paragraph 2)
sturdy, rigid gate structure, suitable for the automated system
smooth, uniform gate movement, without any friction and jam-
ming during the entire opening;
adequately sturdy hinges, in good condition
an efficient earth socket for connection of the operator
We advise you to carry out the metalwork jobs if any, before
installing the automated system.
The condition of the gate structure directly influences the re-
liability and safety of the automated system.
If the leaf to be motorised incorporates a door for the pedestrian
passage it is compulsory to add a safety switch on the door,
connected to the stop input, in order to inhibit the operation
of the automated system when the door is open.
The gearmotor cannot be used to move safety exits or gates
fitted on emergency routes (escape routes).
4.2 INSTALLATION DIMENSIONS
Procedure for finding the securing position of the operator, using
Fig. 5 to help you:
measure dimension Aof the gate and trace a horizontal line
COMPAS 24 - COMPAS 24C
ENGLISH
Guide for the installer
Page 7
on the graph on the measured value, this line to cross the whole
graph.
you will obtain the maximum permissible angular opening accor-
ding to dimension “A” of the graph.
select the opening range you require
select dimension Bso that it intersects the horizontal line (di-
mension “A”) inside the required opening range.
If dimension Apermits opening values greater than the ope-
ning value selected, the value of dimension “B” can change
up to the maximum permissible opening value.
Make sure that the minimum dimension of 450mm in Fig. 5 is
observed.
When the operator has been installed, check if dimension “X”
in Fig. 5 is minimum 500 mm. If dimension “X” is less than
500 mm, run an impact test on the point indicated in Fig. 5,
as described in UNI EN12445 standard, and make sure that
the measured values conform to the specifications of UNI
EN 12453 standard.
If the thrust values are not within the values specified in UNI
EN12453 standard, the zone indicated in figure 5 MUST be
protected with a protective device conforming to the UNI
EN12978 standard.
The operator was studied and made to be secured vertically
(Fig. 6). The operator cannot be installed in other positions.
4.3. INSTALLING THE OPERATOR
When you have established dimensions Aand B”, you can install
the operator as follows:
Loosen by about 1/2 turn the four securing screws of the upper
housing (Fig. 7 ref. a) and withdraw the housing. Set the operator
for manual operation, see paragraph 6.
Establish the height of the operator, bearing in mind that:
the securing bracket of the curved arm must be in a zone
where it can be secured to the gate leaf (Fig. 8)
the minimum off ground height of the operator must permit
securing the curved arm and positioning the lower housing (at
least 85 mm, see fig. 8).
the lower edge of the rear bracket must be aligned with res-
pect to the upper edge of the front bracket (Fig. 9).
Secure the rear bracket in the position you had established, using
four M8 screws. As you secure the bracket, respect the lay-out in
Fig. 10 and check, using a level, if the bracket is horizontal.
To improve water tightness, the external housing covers the
securing bracket - this prevents the bracket from being
directly welded on the pilaster.
The rear bracket must be secured on an as smooth as possible
surface. For masonry pilasters, a counter-plate for walling is
available as an accessory.
Position the operator on the bracket you have just secured, using
two M8x100 screws and the relevant nuts - supplied (Fig. 11).
Set the operator for manual operation, see paragraph 6.
Install the straight arm (Fig. 12) with the supplied screw.
Assemble the rest of the arm as illustrated in Fig. 13.
For correct operation, tighten the two securing screws (Fig.
13 ref. a) and then loosen them by about 1/2 turn to enable
rotation without any friction on the arms.
Align the arms you have just assembled, pushing in the central
zone until they stop, see Fig. 14 ref. a.
There are two stops on the curved arm to facilitate the ali-
gning operation.
Rest the front bracket on the leaf, Fig. 14 ref. b.
Move back the front bracket by about 20 mm and mark the
securing holes, Fig. 14 ref. c.
Secure the bracket in the established position using two M8
screws.
We advise you to secure the bracket with the screws, and
not weld it to the leaf, in order not to rule out future adjust-
ments.
Move the bracket by hand and - with the leaf in closing position
- make sure that the two arms do not impact each other, as
shown in Fig. 14 ref. b.
Take the operator back to the work position - see paragraph
6.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
4.4. WIRING THE OPERATOR
When you have finished securing the operator, you can wire it.
There are three holes in the lower part of the operator. They should
be used for positioning the cable grippers, for routing the power
cables, for connecting accessories and, if necessary, for connecting
the second motor.
Install all the three supplied cable grippers with the securing
nuts (Fig. 15).
Always use the largest cable gripper (Fig. 15 ref. a)
If the other two cable grippers are not used, they must be
closed, using the supplied plugs (Fig. 15 ref. b). Fit the plastic
plug in the cable routing hole and close the cable gripper
until it is tight.
Connect the power cable, as shown in Fig. 16. The earthing wire
must also be connected. Make sure that the power cable wires
are correctly fitted in the ‘comb’ which restrains them Fig. 16.
If the protective fuse has to be replaced, use a fuse with the
following characteristics: 5x20 2A 450V.
Wire all the accessories and safety devices, observing the re-
levant instructions.
4.5. POSITIONING THE MECHANICAL STOPS
The COMPAS operator is supplied standard with opening and clo-
sing mechanical stops. This is to facilitate the installation operations
because there is no need to construct the mechanical stop ele-
ments. The mechanical stops should be fitted in the lower part of
the operator, coupled to a toothed sector. Installation procedure
for the stops:
opening mechAnicAl stop
Set the operator for manual operation, see paragraph 6.
Manually move the leaf to its opening position.
Take the mechanical stop as close as possible to the straight
arm and fasten the two securing screws.
Make sure that the toothed sector is coupled correctly.
closing mechAnicAl stop
Use the closing mechanical stop only in the absence of a
mechanical stop on the closing leaf.
The closing mechanical stop does not guarantee locking the
leaf in case of burglary.
Set the operator for manual operation, see paragraph 6.
Manually move the leaf to its closed position.
Take the mechanical stop as close as possible to the straight
arm and fasten the two securing screws.
Make sure that the toothed sector is coupled correctly.
5. AUTOMATED SYSTEM TEST
When you have made all the necessary electrical connections,
power up the system and program the control unit according to
your requirements.
Run the test for the automation and for all the connected acces-
sories, taking great care when checking the safety devices.
Re-locate the upper covering housing, tighten the securing screws
and position the four covering plugs fig. 18 ref. a.
Position the lower housing as shown in fig. 18 ref. b.
Hand the “User’s Guide” booklet to the customer and describe
its correct operation and use.
Point out, to the end user, any residual risks present in the
installation.
6. MANUAL MODE OPERATION
If the operator has to be manually activated due to a power cut
or to an operator fault, proceed as follows:
Cut power to the system with the differential switch.
Lift the protective plug from the lock, fig. 19 ref. a.
Fit the key and turn it anti-clockwise until it stops, fig. 19 ref. b.
Turn the release knob clockwise until it stops, fig.19 ref. c.
Move the leaf by hand.
procedure for restoring normAl operAtion:
Make sure that the system is not powered.
Position the leaf to its closing position.
Turn the release knob anti-clockwise until it stops, then turn the
key clockwise until it stops and remove it.
Check if the release device has been correctly engaged, by
trying to move the leaf by hand. The leaf must be locked and
it must not be possible to move it by hand.
1.
2.
3.
1.
2.
3.
1.
2.
3.
1.
2.
3.
4.
5.
1.
2.
3.
4.
COMPAS 24 - COMPAS 24C
ENGLISH
Guide for the installer
Page 8
Re-position the lock covering plug.
Restore power to the system and command an opening
cycle.
The operator may not correctly execute the decelerations
on the first cycle. Wait for the end of the cycle and give
another opening command.
7. SPECIAL APPLICATIONS
Applications other than those in this manual are EXPRESSLY PROHI-
BITED
8. MAINTENANCE
To ensure correct long-term operation and a constant level of sa-
fety, we advise you to generally control the system every 6 months.
In the “User’s Guide” booklet, there is a form for recording jobs.
9. REPAIRS
The User must not in any way attempt to repair or to take direct
action and must solely contact qualified GENIUS personnel or
GENIUS service centres.
10. ACCESSORIES
For accessories, see the GENIUS catalogue.
5.
6.
COMPAS 24 - COMPAS 24C
Immagini - Images - Images - Imágenes - Bilder - Afbeeldingen
Pag. 1
Fig. 01
Fig. 02
Fig. 03
Fig. 04
Fig. 06
Fig. 07
Fig. 05
COMPAS 24 - COMPAS 24C
Immagini - Images - Images - Imágenes - Bilder - Afbeeldingen
Pag. 2
Fig. 08 Fig. 09
Fig. 10 Fig. 11
Fig. 12 Fig. 13
Fig. 14 Fig. 15
COMPAS 24 - COMPAS 24C
Immagini - Images - Images - Imágenes - Bilder - Afbeeldingen
Pag. 3
Fig. 16 Fig. 17
Fig. 18
Fig. 19
COMPAS 24 - COMPAS 24C
ENGLISH
Instructions for use
Page 3
Read the instructions carefully before using the product and
store them for future use
GENERAL SAFETY REGULATIONS
If correctly installed and used, the COMPAS automated system will
ensure a high degree of safety. Some simple rules on behaviour can
prevent accidental trouble:
Do not stand near the automated system, and do not allow chil-
dren, persons or things to do so, especially when it is operating.
Keep radio-controls, or any other pulse generators that could
involuntarily activate the automated system, well away from
children.
Do not allow children to play with the automated system.
Do not willingly obstruct gate movement.
Prevent any branches or shrubs from interfering with gate mo-
vement.
Keep the indicator-lights efficient and easy to see.
Do not attempt to activate the gate by hand unless you have
released it.
In the event of malfunctions, release the gate to allow access and
wait for qualified technical personnel to do the necessary work.
When you have set manual operation mode, cut power to the
system before restoring normal operation.
Do not in any way modify the components of the automated
system.
The User must not in any way attempt to repair or to take direct
action and must solely contact qualified GENIUS personnel or
GENIUS service centres.
At least every six months: arrange a check by qualified personnel
of the automated system, safety devices and earth connec-
tion.
DESCRIPTION
The COMPAS automated system is ideal for controlling vehicle
access areas in residential environments.
For details on sliding gate behaviour in different function logics,
consult the installation Technician.
Automated systems include safety devices (photocells) that pre-
vent the gate from closing when there is an obstacle in the area
they protect.
The system ensures mechanical locking when the motor is not ope-
rating and, therefore, for gates of less than 2m in length, installing
a lock is unnecessary.
Manual opening is, therefore, only possible by using the release
system.
The built-in control unit has an adjustable electronic clutch enabling
safe use of the automated system.
A handy manual release facility makes it possible to move the gate
in the event of a power cut or fault.
The warning-light indicates that the gate is currently moving.
MANUAL MODE OPERATION
If the operator has to be manually activated due to a power cut
or to an operator fault, proceed as follows:
Cut power to the system with the differential switch.
Lift the protective plug from the lock, fig. 1 ref. a.
Fit the key and turn it anti-clockwise until it stops, fig. 1 ref. b.
Turn the release knob clockwise until it stops, fig. 1 ref. c.
Move the leaf by hand.
1.
2.
3.
4.
5.
Fig. 01
RESTORING NORMAL OPERATION MODE
Procedure to return the operator to normal work condition:
Make sure that the system is not powered.
Position the leaf about halfway of the memory-stored ope-
ning.
Turn the release knob anti-clockwise until it stops, then turn the
key clockwise until it stops and remove it.
Check if the release device has been correctly engaged, by
trying to move the leaf by hand. The leaf must be locked and
it must not be possible to move it by hand.
Re-position the lock covering plug.
Restore power to the system and command an opening
cycle.
MAINTENANCE
To ensure correct long-term operation and a constant level of sa-
fety, we advise you to generally control the system every 6 months.
In the “User’s Guide” booklet, there is a form for recording jobs.
REPAIRS
The User must not in any way attempt to repair or to take direct
action and must solely contact qualified GENIUS personnel or
GENIUS service centres.
1.
2.
3.
4.
5.
6.
REGISTRO DI MANUTENZIONE / MAINTENANCE REGISTER / REGISTRE D’ENTTRETIEN / REGI-
STRO DE MANTENIMIENTO / WARTUNGSPROGRAMM / ONDERHOUDREGISTER
Dati impianto / System data / données de l’installation / Datos equipo / Daten der Anlage / Gegevens
installatie
Installatore / Installer / Installateur / Installador / Monteur / installateur
Cliente / Customer / Client / Cliente / Kunde / Klant
Tipo impianto / Type of system / Type d’installation / Tipo de equipo /
Art der Anlage / Type installatie
Matricola / Serial No. / de série / de serie / Seriennummer / Se-
riennummer
Data installazione / Installation date / Date d’installation / Fecha de
installatión / Installationsdatum / datum installatie
Attivazione / Start-up / Activation / Activación / Inbetriebnahme /
Activering
Configurazione impianto / System configuration / Confijguration de l’installation / Configuración del equi-
po / Konfiguration der Anlage / Configuratie installatie
COMPONENTE / PART / COMPOSANT / COMPONENTE
/ BAUTEIL / ONDEREEL
MODELLO / MODEL / MODÈLE / MODE-
LO / MEDELL / MODEL
MATRICOLA / SERIAL NUMBER / N° DE
SERIE / N° DE SERIE / SERIENNUMMER /
SERIENUMMER
Operatore / Operator / Opérateur / Operador / Antrieb
/ Aandrijving
Dispositivo di sicurezza 1 / Safety device 1 / dispositif
de sécurité 1 / Dispositivo de seguridad 1 / Scherhelt-
svorrichtung 1 / Velligheldsvoorziening 1
Dispositivo di sicurezza 2 / Safety device 2 / dispositif
de sécurité 2 / Dispositivo de seguridad 2 / Scherhelt-
svorrichtung 1 / Velligheldsvoorziening 2
Coppia di fotocellule 1 / Pair of photocells 1 / Paire de
photocellules 1 / Par de fotocélulas 1 / Fotozellenpaar
1 / Paar fotocellen 1
Coppia di fotocellule 2 / Pair of photocells 2 / Paire de
photocellules 2 / Par de fotocélulas 2 / Fotozellenpaar
2 / Paar fotocellen 2
Dispositivo di comando 1 / Control device 1 / Dispositif
de commande 1 / Dispositivi de mando 1 / Schaltvor-
richtung 1 / Bedieningsvoorziening 1
Dispositivo di comando 2 / Control device 2 / Dispositif
de commande 2 / Dispositivi de mando 2 / Schaltvor-
richtung 2 / Bedieningsvoorziening 2
Radiocomando / Radio control / Radiocommande /
Radiomando / Funksteuerung / Afstandsbediening
Lampeggiante / Flashing lamp / Lampe clignotante /
Destellador / Blinkleuchte / Signaallamp
Indicazione dei rischi residui e dell’uso improprio prevedibile / Indication of residual risks and of foreseeable improper use / Indi-
cation des risques résiduels et de l’usage impropre prévisible / Indicación de los riesgos residuos y del uso impropio previsible /
Angabe der Restrisiken und der voraussehbaren unsachgemäßen Anwendung / Aanduiding van de restrisico’s en van voorzienbaar
oneigenlijk gebruik
Registro di manutenzione - Maintenance register - Registre d’enttretien
Registro de mantenimeinto - Wartungsprogramm - Onderhoudregister
Registro di manutenzione - Maintenance register - Registre d’enttretien
Registro de mantenimeinto - Wartungsprogramm - Onderhoudregister
Nr
Data / Date
/ Date /
Fecha /
Datum /
Datum
Descrizione intervento / Job description / Description de
l’intervention / Descripción de la intervención / Beschrei-
bung der Arbeiten / Beschrijving ingreep
Firme / Signatures / Signatures / Firma / Unterschrift /
Handtekeningen
1
Tecnico / Technicia
Technicien / Técnico
Techniker / Technicus
Cliente / Customer
Client / Cliente
Kunde / Klant
2
Tecnico / Technicia
Technicien / Técnico
Techniker / Technicus
Cliente / Customer
Client / Cliente
Kunde / Klant
3
Tecnico / Technicia
Technicien / Técnico
Techniker / Technicus
Cliente / Customer
Client / Cliente
Kunde / Klant
4
Tecnico / Technicia
Technicien / Técnico
Techniker / Technicus
Cliente / Customer
Client / Cliente
Kunde / Klant
5
Tecnico / Technicia
Technicien / Técnico
Techniker / Technicus
Cliente / Customer
Client / Cliente
Kunde / Klant
6
Tecnico / Technicia
Technicien / Técnico
Techniker / Technicus
Cliente / Customer
Client / Cliente
Kunde / Klant
7
Tecnico / Technicia
Technicien / Técnico
Techniker / Technicus
Cliente / Customer
Client / Cliente
Kunde / Klant
8
Tecnico / Technicia
Technicien / Técnico
Techniker / Technicus
Cliente / Customer
Client / Cliente
Kunde / Klant
9
Tecnico / Technicia
Technicien / Técnico
Techniker / Technicus
Cliente / Customer
Client / Cliente
Kunde / Klant
10
Tecnico / Technicia
Technicien / Técnico
Techniker / Technicus
Cliente / Customer
Client / Cliente
Kunde / Klant
Le descrizioni e le illustrazioni del presente manuale non sono impegnative. GENIUS si riserva il diritto, lasciando inalterate le carat-
teristiche essenziali dell’apparecchiatura, di apportare in qualunque momento e senza impegnarsi ad aggiornare la presente pub-
blicazione, le modifiche che essa ritiene convenienti per miglioramenti tecnici o per qualsiasi altra esigenza di carattere costruttivo
o commerciale.
The descriptions and illustrations contained in the present manual are not binding. GENIUS reserves the right, whils leaving the main
features of the equipments unaltered, to undertake any modifications to holds necessary for either technical or commercial reasons,
at any time and without revising the present publication.
Les descriptions et les illustrations du présent manuel sont fournies à titre indicatif. GENIUS se réserve le droit d’apporter à tout mo-
ment les modifications qu’elle jugera utiles sur ce produit tout en conservant les caractéristiques essentielles, sans devoir pour autant
mettre à jour cette publication .
Las descripciones y las ilustraciones de este manual no comportan compromiso alguno. GENIUS se reserva el derecho, dejando
inmutadas las características esenciales de los aparatos, de aportar, en cualquier momento y sin comprometerse a poner al día la
presente publicación, todas las modificaciones que considere oportunas para el perfeccionamiento técnico o para cualquier otro
tipo de exigencia de carácter constructivo o comercial.
Die Beschreibungen und Abbildungen in vorliegendem Handbuch sind unverbindlich. GENIUS behält sich das Recht vor, ohne die
wesentlichen Eigenschaften dieses Gerätes zu verändern und ohne Verbindlichkeiten in Bezung auf die Neufassung der vorliegenden
Anleitungen, technisch bzw, konstruktiv / kommerziell bedingte Verbesserungen vorzunehmen.
De beschrijvingen in deze handleiding zijn niet bindend. GENIUS behoudt zich het recht voor op elk willekeurig moment de verande-
ringen aan te brengen die het bedrijf nuttig acht met het oog op technische verbeteringen of alle mogelijke andere productie- of
commerciële eisen, waarbij de fundamentele eigenschappen van het apparaat gehandhaafd blijven, zonder zich daardoor te
verplichten deze publicatie bij te werken.
Timbro rivenditore: / Distributor’s stamp: / Timbre de l’agent: / Sello del revendedor: / Fachhändlerstempel: / Stempel dealer:
Via Padre Elzi, 32
24050 - Grassobbio
BERGAMO-ITALY
tel. 0039.035.4242511
fax. 0039.035.4242600
www.geniusg.com
00058I0593 Rev.2
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

Genius COMPAS 24 24C Istruzioni per l'uso

Categoria
Gate Opener
Tipo
Istruzioni per l'uso