Zenith Concierge H25F36DT Manuale utente

Marca: Zenith

Modello: Concierge H25F36DT

Categoria: TV LCD

Tipo: Manuale utente

Installation / Operating Guide | Warranty

Concierge TVs

RECORD TV MODEL NUMBER

The model and serial number of the Concierge

TV are located

on the back of the TV cabinet. For future convenience, we

suggest that you record the numbers here:

MODEL NO.____________________________________

SERIAL NO.____________________________________

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.

REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence

of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a

risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating

and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

POWER CORD POLARIZATION:

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE

CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

NOTE TO CABLE/TV INSTALLER:

This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National Electric Code

(U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be

connected to the grounding system of the building, as close to the point of the cable entry as practical.

REGULATORY INFORMATION:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

Do not attempt to modify this product in any way without written authorization from Zenith Electronics Corporation.

Unauthorized modification could void the user’s authority to operate this product.

COMPLIANCE:

The responsible party for this product’s compliance is:

Zenith Electronics Corporation, 2000 Millbrook Drive, Lincolnshire, IL 60069, USA. Phone: 1-847-941-8000.

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Concierge

is a trademark of Zenith Electronics Corporation

2-WIRE COMM-WARN

For Customer Support/Service please call:

1-888-865-3026

www.zenith.com

PAGE 3

1. Read Instructions

All the safety and operating instructions should be read

before the product is operated.

2. Follow Instructions

All operating and use instructions should be followed.

3. Retain Instructions

The safety and operating instructions should be retained for

future reference.

4. Heed Warnings

All warnings on the product and in the operating instruc-

tions should be adhered to.

5. Cleaning

Unplug this product from the wall outlet before cleaning.

Do not use liquid cleaners or aerosol cleaners. Use a damp

cloth for cleaning.

6. Water and Moisture

Do not use this product near water for example, near a

bath tub, wash bowl, kitchen sink, or laundry tub, in a wet

basement, or near a swimming pool.

7. Accessories, Carts, and Stands

Do not place this product on a slippery or tilted surface, or

on an unstable cart, stand, tripod, bracket, or table. The

product may fall, causing serious injury to a child or adult,

and serious damage to the product. Use only with a cart,

stand, tripod, bracket, or table recommended by the manu-

facturer, or sold with the product. Any mounting of the

product should follow the manufacturer’s instructions, and

should use a mounting accessory recommended by the man-

ufacturer.

8. Transporting Product

A product and cart combination should be moved with care.

Quick stops, excessive force, and uneven surfaces may

cause the product and cart combination to overturn.

9. Attachments

Do not use attachments not recommended by the product

manufacturer as they may cause hazards.

10. Ventilation

Slots and openings in the cabinet are provided for ventila-

tion and to ensure reliable operation of the product and to

protect it from overheating, and these openings must not

be blocked or covered. The openings should never be

blocked by placing the product on a bed, sofa, rug, or

other similar surface. This product should not be placed in

a built-in installation such as a bookcase or rack unless

proper ventilation is provided or the manufacturer’s instruc-

tions have been adhered to.

11. Power Sources

This product should be operated only from the type of

power source indicated on the marking label. If you are not

sure of the type of power supply to your home, consult

your product dealer or local power company. For products

intended to operate from battery power, or other sources,

refer to the operating instructions.

12. Power Cord Polarization

This product is equipped with a polarized alternating-cur-

rent power plug (a plug having one blade wider than the

other). This plug will fit into the power outlet only one

way. This is a safety feature. If you are unable to insert the

plug fully into the outlet, try reversing the plug. If the

plug should still fail to fit, contact your electrician to

replace your obsolete outlet. Do not defeat the safety pur-

pose of the polarized plug.

13. Power Cord Protection

Power-supply cords should be routed so that they are not

likely to be walked on or pinched by items placed upon or

against them, paying particular attention to cords at plugs,

convenience receptacles, and the point where they exit

from the product.

Important safeguards for you and your new product

This product has been manufactured and tested with your safety in mind. However, improper use can result in potential

electrical shock or fire hazards. To avoid defeating the safeguards that have been built into the new product, please read

and observe the following safety points when installing and using the new product, and save them for future reference.

Observing the simple precautions discussed in this operating guide can help the user get many years of enjoyment and safe

operation that are built into the new product.

This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association.

PORTABLE CART WARNING

(Continued on next page)

IMPORTANT SAFETY INSTRUCTIONS

206-3489-O

(Continued from previous page)

14. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the

product, be sure the antenna or cable system is grounded so

as to provide some protection against voltage surges and

built-up static charges. Article 810 of the National Electrical

Code (U.S.A.), ANSI/ NFPA 70 provides information with

regard to proper grounding of the mast and supporting

structure, grounding of the lead-in wire to an antenna dis-

charge unit, size of grounding conductors, location of

antenna-discharge unit, connection to grounding electrodes,

and requirements for the grounding electrode.

15. Lightning

For added protection for this product (receiver) during a

lightning storm, or when it is left unattended and unused

for long periods of time, unplug it from the wall outlet and

disconnect the antenna or cable system. This will prevent

damage to the product due to lightning and power-line

surges.

16. Power Lines

An outside antenna system should not be located in the

vicinity of overhead power lines or other electric light or

power circuits, or where it can fall into such power lines or

circuits. When installing an outside antenna system,

extreme care should be taken to keep from touching such

power lines or circuits as contact with them might be fatal.

17. Overloading

Do not overload wall outlets and extension cords as this can

result in a risk of fire or electric shock.

18. Object and Liquid Entry

Never push objects of any kind into this product through

openings as they may touch dangerous voltage points or

short-out parts that could result in a fire or electric shock.

Never spill liquid of any kind on the product.

19. Servicing

Do not attempt to service this product yourself as opening

or removing covers may expose you to dangerous voltage or

other hazards. Refer all servicing to qualified service person-

nel.

20. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing

to qualified service personnel under the following condi-

tions:

a. If the power-supply cord or plug is damaged.

b. If liquid has been spilled, or objects have fallen into the

product.

c. If the product has been exposed to rain or water.

d. If the product does not operate normally by following

the operating instructions. Adjust only those controls that

are covered by the operating instructions as an improper

adjustment of other controls may result in damage and will

often require extensive work by a qualified technician to

restore the product to its normal operation.

e. If the product has been dropped or the cabinet has been

damaged.

f. If the product exhibits a distinct change in performance.

21. Replacement Parts

When replacement parts are required, be sure the service

technician has used replacement parts specified by the man-

ufacturer or have the same characteristics as the original

part. Unauthorized substitutions may result in fire, electric

shock, or other hazards.

22. Safety Check

Upon completion of any service or repairs to this product,

ask the service technician to perform safety checks to deter-

mine that the product is in proper operating condition.

23. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as

recommended by the manufacturer. The product may slide or

fall, causing serious injury to a child or adult, and serious

damage to the product.

24. Heat

The product should be situated away from heat sources such

as radiators, heat registers, stoves, or other products

(including amplifiers) that produce heat.

PAGE 4

206-3489-O

Antenna Lead in Wire

Antenna Discharge Unit

(NEC Section 810-20)

Grounding Conductor

(NEC Section 810-21)

Ground Clamps

Power Service Grounding

Electrode System (NEC

Art 250, Part H)

Ground Clamp

Electric Service

Equipment

Example of Grounding According to National Electrical

Code Instructions

NEC - National Electrical Code

IMPORTANT SAFETY INSTRUCTIONS

206-3854

PAGE 5

Table of Contents

Use the steps outlined below as a setup guide and to determine the TV

features that will require adjustment for the needs of the user

Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Important Safety Instructions . . . . . . . . . . . . . . . . 3 - 4

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Step 1. Hook Up TV to Signal Source(s) etc.

TV and other Equipment Hookups

Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Cable service . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Antenna with VCR . . . . . . . . . . . . . . . . . . . . . . . . 8

Cable service with VCR . . . . . . . . . . . . . . . . . . . . . 9

S-Video device . . . . . . . . . . . . . . . . . . . . . . . . . 10

External Speaker . . . . . . . . . . . . . . . . . . . . . . . . 11

Step 2. Channel Search and Reception Setup

Auto Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

(Select Antenna, or cable service and do channel search)

Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . 13

Guest’s Remote Key Functions . . . . . . . . . . . . . . . . . 14

Installer’s Remote Key Functions . . . . . . . . . . . . . . . . 15

On-Screen Menus Overview . . . . . . . . . . . . . . . . . . . . 16

Step 3. Customize the TV’s Features

Setup Menu (Start with page 12, Auto Program)

Add/Del/Blank . . . . . . . . . . . . . . . . . . . . . . . . . 17

Channel Labels . . . . . . . . . . . . . . . . . . . . . . . . . 18

Clock Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Timer (On/Off Timers) . . . . . . . . . . . . . . . . . . . . 20

Captions (Caption/Text) . . . . . . . . . . . . . . . . . . . 21

Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Audio Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Bass, Treble, Balance, Audio Mode,

Front Surround, Sound Rite, Speakers

Video Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Contrast, Brightness, Color, Tint, Sharpness, Picture Pref.

Installer Parental Control Menu . . . . . . . . . . . . 25 - 26

Set up Parental Control

Other Menus and On-Screen Displays . . . . . . . . . . . . 27

Managing the Channel Banks . . . . . . . . . . . . 28 - 29 - 30

Installer Menus . . . . 31 - 32 - 33 - 34 - 35 - 36 - 37 - 38

LT2000 Quickset II Clone Programmer . . . . . . 39 - 40 - 41

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Guest Operation Section (Copy for Guest Usage)

Guest Remote Control Key Functions . . . . . . . . . . . . . 44

Guest Parental Control Menu . . . . . . . . . . . . . . . 45 - 46

Guest Menus and On-Screen Displays . . . . . . . . . . . . . 47

Warranty for Concierge Series TVs . . . . . . . . . . Back Cover

Purchase the Optional Installer’s Remote and Clone Programmer

To preform a normal installation set up, you need an installer’s remote like the LP702, and the LT2000 Quickset II Clone

Programmer - - both are shown and described in later sections. The installer remote allows access to the Installer and,

User menus. The installer remote has Menu, Select, and Adjust keys (Down/Left/Right arrow) keys. The LT2000 Quickset

II Clone Programmer is used to duplicate a TV’s setup and install it on another identical TV. See your Zenith Dealer.

Installer/Hotel Note:

Pages 44, 45, 46, and 47 contain information and menus which the guest can use to operate the TV.

It is recommended that these four pages be copied and included with the literature packet that the

lodge provides to guests.

Design and specifications are subject to change without prior notice.

Locate the Antenna/Cable jack on the back of the TV.

Connect the antenna wire that runs from the wall

directly to this jack, according to one of the diagrams

to the right.

Remove the back of the remote and put in two AA

batteries.

Plug in the TV. The TV is designed to operate on stan-

dard current, 120-volt 60 Hertz AC. Do not attempt to

operate it on DC power.

Go to page 12 to Auto Program the TV.

Mini glossary

75 OHM RF CABLE The wire that comes from an off-air antenna or cable service provider. Each end looks like a hex shaped nut with a wire

sticking through the middle, and it screws onto the threaded jack on the back of your TV.

A small device that connects a two-wire 300 ohm antenna to a 75 ohm RF jack. They are usually about an inch long with two screws

on one end and a round opening with a wire sticking out on the other end.

206-3854

Hook Up an Antenna to the TV

PAGE 6

300 TO 75 OHM

ADAPTER

Flat Wire

(300 ohm)

Antenna

300/75 ohm

Adapter

TV Back

S-Video

M.P.I.

R- Audio - L

Antenna

Cable

Video

Matrix

Out

R- Audio - L

TV Back

S-Video

M.P.I.

R- Audio - L

Antenna

Cable

Video

Matrix

Out

R- Audio - L

RF Coaxial Wire

(75ohm)

Antenna

Back of

Remote

120 V AC

60 Hz

Connect an off-air antenna to the TV

If you have a 75 ohm RF cable, then you don’t need

any adapters!

A 300 to 75 ohm adapter is not included with the

Zenith TV.

206-3854

PAGE 7

Hook Up Cable (CATV) to the TV

If you’re using a cable box, leave the TV on channel 3

or 4 and use your cable box to change channels.

If you’re using a cable box, Auto Program might only

find the channel your cable service is on (usually chan-

nel 3 or 4). Don’t worry, that’s all you need!

TV Back

S-Video

M.P.I.

R- Audio - L

Antenna

Cable

Video

Matrix

Out

R- Audio - L

Cable TV

Wall Jack

Round Wire

(75ohm)

TV Back

S-Video

M.P.I.

R- Audio - L

Antenna

Cable

Video

Matrix

Out

R- Audio - L

Cable TV

Wall Jack

Cable Box

Out

RF Coaxial Wire

(75ohm)

3 4

output

switch

Locate the Antenna/Cable jack on the back

of the TV.

Connect the wire that runs from the wall directly

to this jack, according to one of the diagrams to

the right.

Remove the back of the remote and put in

two AA batteries.

Plug in the TV. The TV is designed to operate on

normal current, 120-volt 60 Hertz AC. Do not

attempt to operate it on DC power.

Go to page 12 to Auto Program the TV.

Back of

Remote

120 V AC

60 Hz

Connect cable service to the TV

Locate the Antenna/Cable In jack on the back

of the VCR.

Connect the wire that runs from the antenna,

according to one of the diagrams to the right. As

required, make the other connections as shown to

the right.

Remove the back of the remote, put in

two AA batteries.

Plug in the TV. The TV is designed to operate on

standard current, 120-volt 60 Hertz AC. Do not

attempt to operate it on DC power.

Go to page 12 to Auto Program the TV.

206-3854

PAGE 8

Hook Up Antenna and VCR to the TV

TV Back

S-Video

M.P.I.

R- Audio - L

Antenna

Cable

Video

Matrix

Out

R- Audio - L

Out

Audio

Video

3 4

VCR Back

VCR Back AV Panel

output

switch

Flat Wire

(300 ohm)

Antenna

300/75 ohm

Adapter

A/V cables

not included

with TV

TV Back

S-Video

M.P.I.

R- Audio - L

Antenna

Cable

Video

Matrix

Out

R- Audio - L

Out

Audio

Video

3 4

VCR Back

VCR Back AV Panel

output

switch

A/V cables

not included

with TV

RF Coaxial Wire

(75ohm)

Antenna

Back of

Remote

120 V AC

60 Hz

Connect an off-air antenna and VCR to the TV

No A/V cables are included with the Zenith TV.

Without A/V cables, most VCRs will not play

videocassettes in stereo sound.

206-3854

PAGE 9

Locate the Antenna/Cable In jack on the back of

the VCR.

Connect the wire that runs from the wall, accord-

ing to one of the diagrams to the right. As

required, make the other connections as shown to

the right.

Remove the back of the remote, put in

two AA batteries.

Plug in the TV. The TV is designed to operate on

standard current, 120-volt 60 Hertz AC. Do not

attempt to operate it on DC power.

Go to page 12 to Auto Program the TV.

Hook Up Cable Service (CATV) and VCR

TV Back

S-Video

M.P.I.

R- Audio - L

Antenna

Cable

Video

Matrix

Out

R- Audio - L

Out

Audio

Video

3 4

VCR Back

VCR Back AV Panel

output

switch

A/V cables

not included

with TV

Cable Box

Out

RF Coaxial Wire

(75ohm)

3 4

output

switch

TV Back

S-Video

M.P.I.

R- Audio - L

Antenna

Cable

Video

Matrix

Out

R- Audio - L

Out

Audio

Video

3 4

VCR Back

VCR Back AV Panel

output

switch

A/V cables

not included

with TV

RF Coaxial Wire

(75ohm)

Cable TV

Wall Jack

Back of

Remote

120 V AC

60 Hz

Connect a VCR and Cable service to the TV

Leave the VCR and the television tuned to channel three

and use the cable box to change channels.

No A/V cables are included with your TV. Without A/V

cables, most VCRs will not play videocassettes in stereo

sound.

PAGE 10

206-3854

S-Video Hook Up

Connect an external S-Video device to the TV

TV Back

S-Video

M.P.I.

R- Audio - L

Antenna

Cable

Video

Matrix

Out

R- Audio - L

S-Video cable

not included

with TV

S-Video Device

S-Video

Device

Connections

Panel

S-Video Out

Audio Out

R L

Locate the S-Video out jack on the back of the

VCR or other S-Video device.

Connect the S-Video cable from the device to the

TV S-Video In jack, according to the diagram to

the right. As required, make the other audio con-

nections as shown to the right.

Remove the back of the remote, put in

two AA batteries.

Plug in the TV. The TV is designed to operate on

standard current, 120-volt 60 Hertz AC. Do not

attempt to operate it on DC power.

Go to page 12 to Auto Program the TV.

Back of

Remote

120 V AC

60 Hz

No S-Video cable or audio cables are provided with the TV. Since

S-Video is for Video only, you must connect audio cables or there

will be no sound for the S-Video source.

PAGE 11

206-3854

A/V cables

not included

with TV

Audio In

Speaker Back

TV Back

S-Video

M.P.I.

R- Audio - L

Antenna

Cable

Video

Matrix

Out

R- Audio - L

External Speaker Hook Up

Locate the Audio In jack on the back of the

speaker.

Connect a standard audio cable from the

Matrix Out jack on the TV, to the Audio In

jack on the external speaker.

Connect an external speaker to the TV

PAGE 12

206-3751

Auto Program (Channel Search)

TIMER

CH PREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

ALARM

ADJ

SELECT

3/5

AUTO PROGRAM

ADD/DEL/BLNK

CH. LABELS

CLOCK SET

TIMER

CAPTIONS

LANGUAGE

TO PROGRAM

SETUP MENU

4/6

Use Auto Program to specify Antenna or cable service

incoming signal source and automatically store all of the

channels that are found by channel search

With the optional Installer remote control in hand, press

the POWER key to turn on the TV.

Press MENU repeatedly until the Setup menu appears.

Using SELECT on the remote control, highlight Auto

Program on the screen.

Press the Right or Left ADJ (Adjust) arrow to go to the

Auto Program menu.

Using SELECT, choose either Cable TV or Off-Air Antenna

on your screen. (The flashing option is selected.)

Press the Right or Left ADJ arrow to begin the Channel

Search.

Press ENTER when finished.

Mini glossary

OFF-AIR-ANTENNA If the guest can only view over-the-air broadcasts, select Antenna.

CABLE If you provide cable service to your guests, select Cable.

Auto Program finds channels being received by the TV tuner.

Cable will not work unless a cable service is present.

PAGE 13

206-3751

Front Panel Controls

Use the front control panel to access the menus or just operate the TV

Note: Item 10 Key Defeat, in the installer’s menu allows the installer to:

Set Menu Option 10, Key defeat to “0” - Front panel controls give access to menus.

Set Menu Option 10, Key defeat to “1” - Menus not available with front panel controls.

You can use Channel to tune to available channels and

Volume to set the sound level, regardless of the key

defeat setting.

Press POWER to turn the TV on.

To access the menus, press the MENU button on

the control panel. Cycle through the various

menus by pressing MENU repeatedly.

Use the SELECT button to highlight the option

you want to modify.

Use either the Right or Left ADJUST button to

modify the option you have chosen.

Press CAPTIONS to turn captions on and off.

The menu will disappear after a few seconds.

TV Operation

Power turns the TV on and off.

Channel Up/Down tunes to next channel.

Volume Up/Down adjusts sound level.

Captions turns selected Caption/Text option on

and off.

Camport: Front Audio/Video Inputs

Video Input

L-Audio-R Inputs

Used for stereo sound from various types of

equipment.

adjust select menu

captions volume channel power

L audio R

video in

Typical Front Panel Controls

PAGE 14

206-3854

Guest Remote Key Functions

TIMER ALARM

CH PREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

remote control part number

SC652Z

124-213-18

6710V00108A

FLASHBK (FLASHBACK)

Returns to the last channel viewed.

POWER

Turns TV On or Off

CHANNEL (UP/DOWN)

Scrolls through available channels, and the

Video Channel (Audio/Video source).

MUTE

Turns sound Off and On, while the picture

remains.

ENTER

Press to view the

Channel/Time/Audio display or to

remove any on-screen

display or menu.

NUMBER KEYPAD

Used to key-in numbers and select channels

directly: key-in channel numbers and press

ENTER to go to new channel

TIMER

Press repeatedly to set the TV turn-off

time from 10 minutes up to 4-hours.

Sets AM or PM in Clock/Alarm menus.

VOLUME (LEFT/RIGHT)

Adjusts the sound level.

CHANNEL PREVIEW

Displays the available TV channels, including

access to guest’s Parental Control menu (if

Active). Allows guest to select the Video

source. (Use the Audio/Video jacks on the

back of the TV as the source of the picture

and sound.)

CC (CLOSED CAPTIONING)

Direct access to closed captions.

Press ENTER to exit.

A quick list of the keys on the guest remote and what they do

ALARM

Press to go to the Alarm menu. Set a time for

the TV to turn itself on.

NOTE:

The channel and volume keys can be used by the guest to select and adjust the Parental

Control settings, if the installer activates the Parental Control (V-CHIP) option in the

Installer menu.

206-3751

PAGE 15

Installer Remote Key Functions

TIMER

CH PREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

ALARM

ADJ

SELECT

remote control part number

LP702

124-213-04

FLASHBK (FLASHBACK)

Returns to the last channel viewed.

POWER

Turns TV On or Off

CHANNEL (UP/DOWN)

Chooses next available channel.

MUTE

Turns sound Off and On, while the picture

remains.

ENTER

Press to view the Channel/Time display or

to remove any on-screen display or menu.

TIMER

Press repeatedly to adjust TV turn-off time

from 10 minutes up to 4-hours.

Sets AM or PM in Clock/Alarm menus.

VOLUME (LEFT/RIGHT)

Adjusts the sound level.

CC (CLOSED CAPTIONING)

Direct access to closed captions.

Press ENTER to exit.

A quick list of the keys on the optional LP702 installer’s remote and what they do

ALARM

Press to go to the Alarm menu. Set a time

for the TV to turn itself on.

MENU/SELECT/ADJ (ADJUST)

Adjusts on-screen menus and options.

Press MENU repeatedly to scroll through

menus. Use SELECT to choose an option

and ADJ (adjust) Left/Right to change

the selected option.

CHANNEL PREVIEW

Gives installer access to the guest’s

menus. Displays the available TV channels

and hotel guest’s Parental Control menu

(if active). Selects the Video source. (Use

the Audio/Video jacks on the back of the

TV as the source of the picture and

sound.)

TV/FM

Selects TV or Radio mode on TVs equipped

with FM radio.

NUMBER KEYPAD

Used to key-in numbers and select chan-

nels directly: key-in channel numbers

and press ENTER to go to new channel

PAGE 16

206-3751

On-Screen Menus Overview

ON-SCREEN MENUS

SETUP MENU Adjusts the basic operational features of the TV

Auto Program 12 Automatically finds and stores active channels to scroll through using Channel Up/Down.

Add/Del/Blnk 17 Manually picks and chooses which active channels will appear when using Channel Up/Down

Channel Labels 18 Labels the channels with their network names (ABC, CBS, HBO, etc.).

Clock Set 19 Sets the time.

Timer 20 Sets times for the TV to turn itself on and off each day.

Caption/Text 21 Chooses a captioning or text option.

Language 22 Picks the language the on-screen menus will appear in.

AUDIO MENU 23 Customizes the sound. Options are:

Bass, Treble, Balance, Audio Mode, Front Surround, SoundRite, Speakers.

VIDEO MENU 24 Adjusts the picture appearance. The options are: Contrast, Brightness, Color, Tint, Sharpness, Picture Pref.

PARENTAL 25/41 Allows installer/user to block program content for up to 12 hours, with the use of a password.

CONTROL MENU

27 OTHER MENUS AND ON-SCREEN DISPLAYS

Channel/Time Shows the current time, channel, (or video source), type of incoming audio signal, and XDS* info if provided.

Alarm Sets a time the TV will turn itself on.

Sleep Timer Sets a time the TV will turn off.

Volume Shows current sound level.

Captions Used to select Caption/Text options.

Ch Preview Displays the available channels and menus list.

Channel Bank Shows currently selected channel bank.

INSTALLER MENUS

Installer Menus 31 Makes adjustments to the TV’s operational features.

*XDS (Extended Data Service) Additional program information provided at the discretion of the

broadcaster. May include: title of broadcast, elapsed time, and time remaining on program.

Descriptions of the menus and on-screen displays available to the installer

Menu Name Page Description

PAGE 17

206-3751

Setting Add/Delete/Blank

TIMER

CH PREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

ALARM

ADJ

SELECT

CH 44 ADDED

AUTO PROGRAM

ADD/DEL/BLNK

CH. LABELS

CLOCK SET

TIMER

CAPTIONS

LANGUAGE

SETUP MENU

3/5

Fine-tune the guest’s channel selection list

Press the MENU key on the Installer’s remote so the Setup

menu appears.

Press SELECT repeatedly to highlight the Add/Del/Blnk

option.

Using either the NUMBER keypad and ENTER or the

Channel Up/Down arrow on the remote, select a channel.

(If adding a deleted channel, you will need to use the

NUMBER keypad and ENTER.)

Using the Right/Left ADJ arrow, specify whether that

channel is Added, Deleted, or Blank.

To continue, select another channel and repeat Step 4.

When you are finished, press ENTER to remove menu.

Adding Aux, VCR 3, VCR 4, to the Channel

Preview List

Go to the Setup menu, select the Add/Del/Blnk option.

Use Channel Up/Down to select the option and choose

Added.

Note: If the option was turned off in the Service menu,

you will have to reinstate it before it can appear as an

option in the Channel Preview list.

Note: You can specify Add, Delete or Blank for VCR3,

VCR4, and Aux. Caution: If you delete CH3, VCR3 is also

deleted, if you delete CH4, VCR4 is also deleted and vice

versa.

If you delete a channel, it isn’t gone for good. Just select it using

the NUMBER keypad on the remote, or add it later.

Mini glossary

ADD Adds new channels to the list that the guest can scroll through when using the remote.

DELETE Removes channels for one reason or another from the list that the guest can scroll through.

BLANK Removes the video signal from a channel so the guest will only receive the audio signal.

PAGE 18

206-3751

Setting Up Channel Labels

TIMER

CH PREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

ALARM

ADJ

SELECT

AUTO PROGRAM

ADD/DEL/BLNK

CH. LABELS

CLOCK SET

TIMER

CAPTIONS

LANGUAGE

CH 32 ABC

SETUP MENU

Overview

Channel Labels help the user identify the channel or network being viewed.

In the Setup menu with the CH LABELS option highlighted, use the Adjust

Left/Right arrow to scroll through the available channel labels, such as,

A&E, AMC, ESPN, HBO, etc. These are a series of alphabetically organized

preset labels from which you can choose the more common networks. Use

any of these or create custom labels.

- - - - , The 4 dashes will allow a channel label to appear; if one is provid-

ed by XDS. (Extended data service)

NONE, prevents any channel label from appearing.

LAB 1, thru LAB 20, are the 20 programmable labels.

The 20 programmable labels can be customized for your needs.

Each programmable label has 5 characters spaces available.

To Program a Channel Label

First select a channel using the NUMBER keypad and ENTER or the Channel

Up/Down arrow, on the optional Installer’s remote control.

(To select a deleted channel, use the NUMBER keypad and ENTER.)

To program a channel label, go to the Setup menu and select CH LABELS.

Use the Right/Left ADJ adjust arrow to scroll the available preset labels.

Scroll past - - - -, scroll past NONE, to go to the first programmable label

slot, LAB 1. Notice that the label appears with the title LAB 1.

Creating a Custom Channel Label

Use Volume Up/Down to select the first letter.

Use Channel Up/Down to change the character to one of the 255 characters

available.

(A blank letter space is available if required, after the “!” symbol.)

In Channel Labels Mode, use the following keys to:

Adjust Left/Right Move to the next label.

- - move to the next or previous label.

Volume Up/Down Select character spaces

- - move to the next or previous

character space.

Channel Up/Down Scroll through the available characters.

ENTER Accept the custom channel label and

remove the menu.

MUTE Remove any custom label, insert ‘NONE’,

- - if any custom label character space

is selected.

PAGE 19

206-3751

Set the Clock

TIMER

CH PREVIEW

ENTER

ALARM

ADJ

SELECT

Mini glossary

TIME A four-digit figure broken down into hours and minutes, used to enter the current time when setting the clock or wake-up alarm.

HOURS First two digits that are entered when setting the clock or the wake-up alarm.

MINUTES The last two digits that are entered when setting the clock, or the wake-up alarm.

TIMER Chooses AM or PM when setting the clock.

The clock can also be set using 24 hour “military time.” For p.m. settings

add 1200. For example, to set 6:30 p.m., add 1200 to 630, = enter 1830.

For Auto Clock Set to work, TV must be tuned to a channel that has XDS

data available. Auto Clock Set, sets the time only once while the TV is on.

To set the clock with XDS data, turn TV off, then back on again, or set the

clock time manually.

AUTO

EASTERN

CENTRAL

MOUNTAIN

PACIFIC

CLOCK MENU

CLOCK SET

TIME ZONE

DAY. SAVING

AUTO

OFF

10:43 AM

CLOCK MENU

CLOCK SET

TIME SET

MANUAL

TIMER

AUTO PROGRAM

ADD/DEL/BLNK

CH. LABELS

CLOCK SET

TIMER

CAPTIONS

LANGUAGE

SETUP MENU

TO SET CLOCK

AUTO PROGRAM

ADD/DEL/BLNK

CH. LABELS

CLOCK SET

TIMER

CAPTIONS

LANGUAGE

SETUP MENU

TO SET CLOCK

USE SELECT TO CHOOSE

USE ADJ TO CHANGE

USE SELECT TO CHOOSE

USE ADJ TO CHANGE

Clock Auto/Manual Operating Modes Setup

Use MENU, SELECT, and ADJ Left/Right to choose the Clock menu and to

set up the clock menu options, with the optional Installer’s remote.

Clock Mode Auto: TV automatically sets the time.

Time Zone: User can choose the time zone or have the

TV set it automatically.

Day. Savings: User can choose to have daylight

savings adjust the clock time one hour,

or have the TV adjust it automatically.

Manual: User sets the time on the clock.

Press ENTER repeatedly to remove menus.

PAGE 20

206-3584

ON TIME 9:00 AM

OFF TIME 7:00 PM

ON/OFF TIMER

TIMER

AUTO PROGRAM

ADD/DEL/BLNK

CH. LABELS

CLOCK SET

TIMER

CAPTIONS

LANGUAGE

TO SET TIMER

SETUP MENU

Set up On/Off Timers

Note: On/Off Timers oper-

ate independently of each

other.

On the optional Installer’s remote, press MENU

repeatedly until the Setup menu appears.

Press SELECT repeatedly to highlight the Timer option, press

the Right arrow.

Use SELECT to choose an option. Use the number keypad

and/or the Left/Right ADJ arrows to enter the times. Use the

TIMER key to set AM/PM.

Press ENTER to remove menu and return to TV viewing.

Your options are:

• On Time

Sets a time that the TV will turn itself On each day.

• Off Time

Sets a time that the TV will turn itself Off each day.

• On/Off Timer

Enables or disables the On/Off Timer functions. (The On/Off

Timer can be disabled but the settings will be retained.)

The clock must be set before the Timers will function.

The Off Timer can be used to turn the TV off at the preset time.

Note: No On Timer setting is required to use the Off Timer feature.

Mini glossary

TIME A four-digit figure broken down into hours and minutes, used to enter the time when setting the clock or programming timers.

HOURS First two digits that are entered when setting the clock or programming timers.

MINUTES The last two digits that are entered when setting the clock, or programming timers.

TIMER Choose AM or PM with the TIMER button when setting the clock.

Timer

TIMER

CH PREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

ALARM

ADJ

SELECT

La pagina sta caricando ...

Zenith Concierge H25F36DT Manuale utente

Marca: Zenith

Modello: Concierge H25F36DT

Categoria: TV LCD

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: Zenith Concierge H25F36DT User manual

Documenti correlati

Altri documenti

LG H25F36DT Manuale del proprietario