Hoover HIES430B Manuale utente

Thank you for purchasing the HOOVER induction hob. Please read this instruction manual

carefully before using the hob and keep it in a safe place for future reference.

OCAKLAR

KULLANIM VE KURULUM TALİMATLARI

INDUKČNÁ VARNÁ DOSKA

SK

T

INDUKČNÍ VARNÁ DESKA

CZ

SI

Indukcijska kuhalna plošča

Návod na obsluhu

Návod k obsluze

Navodila za uporabo

IT

Piani

cottura

Istruzioni

per

l’ uso

ed

istallazione

KOCHFELDER

GEBRAUCHS- UND INSTALLATIONSANLEITUNG

DE

HIES430B

HIFS430B

Safety Warnings

Your safety is important to us. Please read this

information before using your hob.

Installation

Electrical Shock Hazard

• Disconnect the appliance from the mains

electricity supply before carrying out any work

or maintenance on it.

• Connection to a good earth wiring system is

essential and mandatory.

• Alterations to the domestic wiring system must

only be made by a qualified electrician.

• Failure to follow this advice may result in

electrical shock or death.

Cut Hazard

• Take care - panel edges are sharp.

• Failure to use caution could result in injury or

cuts.

Important safety instructions

• Read these instructions carefully before

installing or using this appliance.

• No combustible material or products should be

placed on this appliance at any time.

• Please make this information available to the

person responsible for installing the appliance

EN-1

By placing the CE mark on this product, we are

confirming compliance to all relevant European safety, health

and environmental requirements which are applicable in

legislation for this product.

as it could reduce your installation costs.

• In order to avoid a hazard, this appliance must

be installed according to these instructions for

installation.

• This appliance is to be properly installed and

earthed only by a suitably qualified person.

• This appliance should be connected to a circuit

which incorporates an isolating switch

providing full disconnection from the power

supply.

• Failure to install the appliance correctly could

invalidate any warranty or liability claims.

Operation and maintenance

Electrical Shock Hazard

• Do not cook on a broken or cracked hob surface.

If the hob surface should break or crack, switch

the appliance off immediately at the mains power

supply (wall switch) and contact a qualified

technician.

• Switch the hob off at the wall before cleaning or

maintenance.

• Failure to follow this advice may result in

electrical shock or death.

Health Hazard

• This appliance complies with electromagnetic

safety standards.

• However, persons with cardiac pacemakers or

EN-2

other electrical implants (such as insulin

pumps) must consult with their doctor or

implant manufacturer before using this

appliance to make sure that their implants will

not be affected by the electromagnetic field.

• Failure to follow this advice may result in death.

Hot Surface Hazard

• During use, accessible parts of this appliance

will become hot enough to cause burns.

• Do not let your body, clothing or any item other

than suitable cookware contact the Induction

glass until the surface is cool.

• Beware: magnetisable metal objects worn on

the body may become hot in the vicinity of the

cooktop. Gold or silver jewellery will not be

affected.

• Keep children away.

• Handles of saucepans may be hot to touch.

Check saucepan handles do not overhang other

cooking zones that are on. Keep handles out of

reach of children.

• Failure to follow this advice could result in

burns and scalds.

Cut Hazard

• The razor-sharp blade of a hob surface scraper

is exposed when the safety cover is retracted.

Use with extreme care and always store safely

EN-3

and out of reach of children.

• Failure to use caution could result in injury or

cuts.

Important safety instructions

• Never leave the appliance unattended when in

use. Boilover causes smoking and greasy

spillovers that may ignite.

• Never use your appliance as a work or storage

surface.

• Never leave any objects or utensils on the

appliance.

• Do not place or leave any magnetisable objects

(e.g. credit cards, memory cards) or electronic

devices (e.g. computers, MP3 players) near the

appliance, as they may be

affected by its electromagnetic field.

• Never use your appliance for warming or

heating the room.

• After use, always turn off the cooking zones

and the hob as described in this manual(i.e. by

using the touch controls). Do not rely on the

pan detection feature to turn off the cooking

zones when you remove the pans.

• Do not allow children to play with the appliance

or sit, stand, or climb on it.

• Do not store items of interest to children in

cabinets above the appliance. Children

EN-4

climbing on the hob could be seriously injured.

• Do not leave children alone or unattended in

the area where the appliance is in use.

• Children or persons with a disability which

limits their ability to use the appliance should

have a responsible and competent person to

instruct them in its use. The instructor should

be satisfied that they can use the appliance

without danger to themselves or their

surroundings.

• Do not repair or replace any part of the

appliance unless specifically recommended in

the manual. All other servicing should be done

by a qualified technician.

• Do not use a steam cleaner to clean your hob.

• Do not place or drop heavy objects on your hob.

• Do not stand on your hob top.

• Do not use pans with jagged edges or drag pans

across the Induction glass surface as this can

scratch the glass.

• Do not use scourers or any other harsh

abrasive cleaning agents to clean your cooktop,

as these can scratch the Induction glass.

• If the power supply cable is damaged, it must

only be replaced by a qualified technician.

• This appliance is designed for domestic use

only.

• This appliance can be used by children aged

from 8 years and above and persons with

EN-5

reduced physical, sensory or mental

capabilities or lack of experience and

knowledge if they have been given supervision

or instruction concerning use of the appliance

in a safe way and understand the hazards

involved. Children shall not play with the

appliance. Cleaning and user maintenance

shall not be made by children without

supervision.

• WARNING: Unattended cooking on a hob with

fat or oil can be dangerous and may result in

fire. NEVER try to extinguish a fire with water,

but switch off the appliance and then cover

flame e.g. with a lid or a fire blanket.

• Metallic objects such as knives, forks, spoons

and lids should not be placed on the hob

surface since they can get hot.

• After use, switch off the hob element by its

control and do not rely on the pan detector.

• The appliance is not intended to be operated by

means of an external timer or separate

remote-control system.

Congratulations on the purchase of your new Induction Hob.

We recommend that you spend some time to read this Instruction / Installation

Manual in order to fully understand how to install correctly and operate it.

For installation, please read the installation section.

Read all the safety instructions carefully before use and keep this Instruction /

Installation Manual for future reference.

EN-6

Product Overview

Top View

1. max. 1800/3000 W zone

2. max. 1800/3000 W zone

3. max. 1800/3000 W zone

4. max. 1400/2000 W zone

5. Flexible zone. 3000/4000 W

6. Glass plate

7. Control

1. max. 1800/3000 W zone

2. max. 1800/3000 W zone

3. max. 1800/3000 W zone

4. max. 1400/2000 W zone

5 - 6. Flexible zone. 3000/4000 W

7. Glass plate

8. Control

EN-7

Control Pane

1. Power / Timer slider touch control

2. Heating zone selection controls

3. keylock control

4. ON/OFF control

5. keep warm control

6. Boost control

7. Timer control

EN-8

A Word on Induction Cooking

Induction cooking is a safe, advanced, efficient, and economical cooking

technology. It works by electromagnetic vibrations generating heat directly in the

pan, rather than indirectly through heating the glass surface. The glass becomes

hot only because the pan eventually warms it up.

Before using your New Induction Hob

• Read this guide, taking special note of the ‘Safety Warnings’ section.

• Remove any protective film that may still be on your Induction hob.

Using the Touch Controls

• The controls respond to touch, so you don’t need to apply any pressure.

• Use the ball of your finger, not its tip.

• You will hear a beep each time a touch is registered.

• Make sure the controls are always clean, dry, and that there is no object (e.g. a

utensil or a cloth) covering them. Even a thin film of water may make the

controls difficult to operate.

iron pot

magnetic circuit

ceramic glass plate

induction coil

induced currents

EN-9

Choosing the right Cookware

• Only use cookware with a base suitable for induction

cooking. Look for the induction symbol on the

packaging or on the bottom of the pan.

• You can check whether your cookware is suitable by carrying out

a magnet test. Move a magnet towards the base of the pan. If it

is attracted, the pan is suitable for induction.

• If you do not have a magnet:

1. Put some water in the pan you want to check.

2. Follow the steps under ‘To start cooking’.

3. If does not flash in the display and the water is heating, the pan is suitable.

• Cookware made from the following materials is not suitable: pure stainless steel, aluminium or

copper without a magnetic base, glass, wood, porcelain, ceramic, and earthenware.

Do not use cookware with jagged edges or a curved base.

Make sure that the base of your pan is smooth, sits flat against the glass, and is

the same size as the cooking zone. Use pans whose diameter is as large as the

graphic of the zone selected. Using a pot a slightly wider energy will be used at its

maximum efficiency. If you use smaller pot efficiency could be less than expected.

Pot less than 140 mm could be undetected by the hob. Always centre your pan on

the cooking zone.

Always lift pans off the Induction hob – do not slide, or they may scratch the glass.

EN-10

Pan Dimension

The cooking zones are, up to a limit, automatically adapted to the diameter of the

pan. However the bottom of this pan must have a minimum of diameter according

to the corresponding cooking zone. To obtain the best efficiency of your hob,

please place the pan in the centre of the cooking zone.

Cooking zone

The base diameter of induction cookware

Minimum (mm)

Maximum (mm)

1,2,3

140

220

Flexible zone

220

220x400

4

140

Cooking zone

The base diameter of induction cookware

Minimum (mm)

Maximum (mm)

1,2,3,4

140

220

Flexible zone

220

220x400

EN-11

HIES430B

HIFS430B

Using your Induction Hob

To start cooking

1. Touch the ON/OFF control.

After power on, the buzzer beeps once, timer control

show “ “ ，heating zone selection controls show

“ “or“ “or“ “, indicating that the induction

hob has entered the state of standby mode.

2. Place a suitable pan on the cooking zone that

you wish to use.

• Make sure the bottom of the pan and the surface

of the cooking zone are clean and dry.

3.Touching the heating zone selection control,

and a indicator upon you touched will flash

4. Adjust heat setting by touching the slider control.

• If you don’t choose a heat setting within 1

minute, the Induction hob will automatically

switch off. You will need to start again at step 1.

• You can modify the heat setting at any time

during cooking.

EN-12

If the display flashes alternately with the heat

setting

This means that:

• you have not placed a pan on the correct cooking zone or,

• the pan you’re using is not suitable for induction cooking or,

• the pan is too small or not properly centred on the cooking zone.

No heating takes place unless there is a suitable pan on the cooking zone.

The display will automatically turn off after 1 minute if no suitable pan is placed

on it.

When you have finished cooking

1. Touching the heating zone selection

control that you wish to switch off

2. Turn the cooking zone off by touching the slider

to the left. Make sure the display shows”0”

3. Turn the whole cooktop off by touching the

ON/OFF control.

4. Beware of hot surfaces

H will show which cooking zone is hot to touch. It will disappear when the

surface has cooled down to a safe temperature. It can also be used as an

energy saving function if you want to heat further pans, use the hotplate

that is still hot.

EN-13

Using the Boost function

Actived the boost function

1. Touching the heating zone selection control

2. Touching the boost control , the zone indicator shows “b” and the power

reach Max.

Cancel the Boost function

1. Touching the heating zone selection control

that you wish to cancel the boost function

2. a: Touching the boost control “ ”, then the cooking zone will revert to its

original setting.

b: Touching the slider control, then the cooking zone will revert to the level

you select.

OR

EN-14

• The function can work in all cooking zones

• The cooking zone returns to its original setting after 5 minutes.

• As the boost function of 1st cooking zone is activated ,the 2nd cooking zone is

limited under level 2 automatically. vice versa

• If the original heat setting equals b, it will return to 15 after 5 minutes

Using the Keep Warm function

Actived the keep warm function

1. Touching the heating zone selection control

2. Touching the keep warm control ,the zone indicator shows “

|

” .

Cancel the keep warm function

Annuler la fonction de conservation au chaud

1. Touching the heating zone selection control

EN-15

2. a: Touching the slider control, then the cooking zone will revert to the level

you select.

b: Touching the function control such as , then the cooking zone will

revert to the level you previously selected.

FLEXIBLE AREA

• This area can be used as a single zone or as two different zones, accordingly to

the cooking needs anytime.

• Flexible area is made of two independent inductors that can be controlled

separately. When working as a single zone, a cookware is moved from one zone

to the other one within the flexible area keeping the same power level of the zone

where the cookware originally was placed, and the part that is not covered by

cookware is automatically switched off.

• Important：Make sure to place the cookwares centered on the single cooking

zone. In case of big pot,oval,rectangular and elongated pans make sure to place

the pans centered on the cooking zone covering both cross.

Examples of good pot placement and bad pot placement.

EN-16

As big zone

1. To activate the flexible area as a single big zone, simply press the dedicated

keys.

2. The power setting works as any other normal area.

3. If the pot is moved from the front to the rear part (or viceversa),the flexible

area detects automatically the new position, keeping the same power.

4. To add a further pot, press again the dedicated keys, in order to detect the

cookware.

As two independent zones

To use the flexible area as two different zones with different power settings, press

the dedicated keys.

EN-17

Locking the Controls

• You can lock the controls to prevent unintended use (for example children

accidentally turning the cooking zones on).

• When the controls are locked, all the controls except the ON/OFF control are

disabled.

To lock the controls

Touch the keylock control. The timer indicator will show “Loc“

To unlock the controls

1. Touch and hold the keylock control for a while.

2. You can now start using your Induction hob.

When the hob is in the lock mode, all the controls are disable except the

ON/OFF , you can always turn the induction hob off with the ON/OFF

control in an emergency, but you shall unlock the hob first in the next

operation.

Over-Temperature Protection

A temperature sensor equipped can monitor the temperature inside the Induction

hob. When an excessive temperature is monitored, the Induction hob will stop

operation automatically.

Detection of Small Articles

When an unsuitable size or non-magnetic pan (e.g. aluminium), or some other

small item (e.g. knife, fork, key) has been left on the hob, the zone automatically

go on to standby in 1 minute. The fan will keep cooling down the induction hob for

a further 1 minute.

Auto Shutdown Protection

Auto shut down is a safety protection function for your induction hob. It shuts

down automatically if ever you forget to turn off your cooking. The default working

times for various power levels are shown in the below table: .

Power level

Keep warm

1~5

6~10

11~14

15

Default working timer (hour)

2

8

4

2

1

When the pot is removed, the induction hob can stop heating immediately and the

hob automatically switch off after 2 minutes.

People with a heart pace maker should consult with their doctor before

using this unit.

EN-18

Using the Timer

You can use the timer in two different ways:

• You can use it as a minute minder. In this case, the timer will not turn any

cooking zone off when the set time is up.

• You can set it to turn cooking zones off after the set time is up.

• You can set the timer for up to 99 minutes.

Using the Timer as a Minute Minder

If you are not selecting any cooking zone

1. Make sure the cooktop is turned on.

Note: you can use the minute minder even if you’re not selecting any cooking

zone.

2. Touch timer control , the “0：10” will show in the

timer display where touched and the “0” flashes.

3. Set the time by touching the slider control. (e.g. 6)

4.Touch timer control again, the “1” will flash.

5. set the time by touching the slider control (e.g.9), now the timer you set is 56

minutes.

EN-19

La pagina sta caricando ...

Hoover HIES430B Manuale utente

Hoover HIES430B Manuale utente

Documenti correlati

Altri documenti