Hoover LBHVP16ALUDE Manuale utente

Marca: Hoover

Modello: LBHVP16ALUDE

Categoria: Lavatrici

Tipo: Manuale utente

Questo manuale è adatto anche per

VISION

washing machine

User instructions

Lavabiancheria

Istruzioni per l’uso

Contents Page

Preface 4

General delivery notes 5

Notes on safety 5

Quick start 6

Useful advice for the user 7

Setting up, installation & testing 8

Using Vision for the first time 12

Description of controls 17

Detergent drawer 22

Detergents, washing aids and amounts to use 23

Programme selector 25

Whisper 26

The main wash 27

Programme guide 30

Cleaning and routine maintenance 32

Trouble shooting 34

Power failure 35

Customer service 36

Technical data 37

Before switching on the appliance make sure it is

correctly installed and that the transit brackets are

removed as shown in page 8.

Programme selector dial

Start/pause button

Door handle

Big wash load button

Timer saver button

Pre wash button

Extra rinse button

Select spin button

Child lock button

Set end time/delay start button

Fast iron button

Detergent drawer

Door locked indicator light

Vision Inter@ct panel

Controls

DEFGH I LM B

General delivery notes

On delivery check that there is the following with the appliance:

–Instruction manual

–Certificate of guarantee

–Caps

–Inlet hose

and check that no damage has occurred during transit, and if so, call your nearest Authorised

Technical Support Service agent (see Customer Service)

Safety notes.

Note: for any cleaning or maintenance procedure for the

washing machine

A) Pull out the plug

B) Turn off the tap

C) Hoover equips all its appliances with earthing. Ensure that the mains supply is earthed,

and if it is not, seek assistance from a qualified person.

CE Appliance complies with European Directive 89/336/EEC, 73/23/EEC and subsequent

amendments.

D) Do not touch the appliance when hands or feet are wet or damp. Do not use the

appliance with bare feet.

E) The use of adapters, multiple connectors and/or extensions is not recommended.

Note:

water temperature can reach 90°C during the wash cycle

F) Check there is no water left in the drum before opening the door.

G) Do not allow children or unauthorised persons to use the appliance without supervision.

H) Do not pull the power cable or the appliance itself to remove the plug from the socket.

I) The appliance must not be exposed to weather conditions (rain, direct sun, etc...)

L) When moving the appliance never lift it by the controls or by the detergent drawer.

Preface

Read these instructions for use and all other information enclosed with the washing machine

and act accordingly.

Keep all documentation for future reference or for any future owners.

Note: this machine is solely for domestic use.

Notes on disposal

All packaging material used is environmentally-friendly and recyclable. Please help dispose of

the packaging via environmentally-friendly means.

Your supplier or local council will be able to give you

details of current means of disposal.

Appliances which are finished with are not worthless rubbish! Valuable materials can be

salvaged via scrap reprocessing.

Note: pull out the mains plug from appliances which are

finished with. Cut the power cable and dispose of it,

together with the plug.

When disposing of an old washing machine, please ensure that the porthole lock is rendered

inoperable to prevent children shutting themselves in the appliance.

Useful advice for users

Tips on using your domestic appliance in the most environmentally-friendly and economical way

Do a full load in your washing machine

To prevent any possible waste of energy, water or detergent we recommend that you

put a full load in your washing machine, not exceed the maximum load size.

Save up to 50% energy by washing a full load instead of 2 half loads.

When is prewashing really needed?

Only with particularly dirty loads! Energy savings of 5 to 15% are made by not selecting the

prewash option for normally soiled laundry.

Which wash temperature should you choose?

Using stain removers before machine washing reduces the need to wash at temperatures

over 60°C. Energy savings of up to 50% can be made by using a 60°C wash temperature.

ARIEL - Chosen and recommended by Hoover

When we produce a new washing machine we subject it to every test possible. And one of the

most important tests is the one that enables our experts to identify the most suitable detergent

for solving laundry problems. Ariel was able to meet our needs: to make the washing machine

function efficiently, not compromise the machine.s lifespan and produce the best wash results.

Consistently excellent results, which was the main aim of the test we carried out, determined

our choice and our recommendation. The prime function of a detergent that answers all

washing requirements is to work with the water to remove dirt from fabrics, holding it in

suspension until it is removed when the water is pumped out, and to control the amount of

foam forming in the washing machine, without damaging the fibres of the items being washed.

Ariel fully satisfies all these requirements, as it contains high quality elements, the result of the

most advanced research, ensuring excellent results under all conditions.

After washing

–Wait about two minutes for the door locking device

to disengage (only if door locked indicator is ON)

– Switch off the machine by turning the control knob

to the STOP position

–Open the door and remove the laundry

Note: Please ensure that Vision set-up, installation and

testing has been completed before referring to the

Quick Start.

When in transit never rest the porthole against the trolley.

M) N.B!

If the appliance is installed on a carpeted floor ensure that the ventilation holes on the

base of the appliance are not obstructed.

N) The appliance should be lifted by two people.

O) If the appliance is not running properly or breaks down, switch it off, turn off the tap and

do not tamper with the appliance.

Consult only the Authorised Technical Support Service for possible repair and ask them to

use original spare parts.

Failure to comply with the above can compromise the safety of the appliance.

P) If the appliance’s power cable should ever need replacing, consult the Authorised

Technical Support Service.

Quick Start

Washing

–Open the door by pressing the button inside the door handle (see fig.PAGE 19).

–Select laundry and put it in the machine.

–Close the door.

–Put detergent in the dispenser compartments (compartment I for pre wash and

compartment II for all other programmes).

–Select programme by turning the programme knob (Your desired programme may be

seen on the display).

–Select any function buttons required and then press the Start/Pause button.

–There may be a short time delay from pressing the start/pause bottom to the start of the

programme, while the machine senses the water required and sets the parameters for the

programme.

Installation & Testing

After removing the machine from the packaging, proceed

as follows:

On the back of the machine

1) Unscrew the screws G and remove the back panel.

2) Unscrew the centre brace A, the two side screws C

and remove the transverse bracket D and the relevant

plastic spacer.

3) Unscrew the 2 B braces and remove them.

This will cause 2 plastic spacers to fall into

the machine.

4) Remove the above-mentioned plastic

spacers.

5) Remove the plastic bags containing the two

polystyrene blocks at the sides.

6) Remount the back panel using the screws G.

7) Cover the holes using the caps enclosed in the

instructions envelope.

8) Level the machine using the two adjustable front feet.

Note: we recommend you keep the transit bracket, braces

and screws to immobilise the machine for future transit.

The Manufacturers will not be responsible for any possible

damage to the machine caused by not following the rules

relating to releasing the mechanism. The user is responsible

for all costs of installation.

ACD

Water supply

The machine has an inlet hose with 3/4» threaded

ferrules fitted to the ends to attach between the threaded

connector on the appliance and the cold water supply.

The appliance must be connected to the water mains

using new hose-sets. The old hose-seta should not be

resused.

The appliance must only be connected to the cold water

supply.

Connection to a warm water supply, that is over 40°,

may damage certain delicate fabrics.

Acqua-stop

The fill hose supplied with this machine has a double skin

and incorporates a water valve . If the inner hose bursts the

valve will automatically shut off the water supply to prevent

flooding. The indicator turns red (A). Should this happen,

turn off the water supply immediately and have a new fill

hose fitted by Hoover Service.

min 50 cm

max 85 cm

+2,6 mt max

max 100 cm

min 4 cm

Safety antitwist

device (press and

twist to remove

the washer)

Red button

blocked valve

indicator

➝

Testing the installation

Refer to the programme guide for details of how to select programmes.

For stopping each programme before its completion, the programme must be cancelled by

holding down the START/PAUSE button for five seconds. The display will inform you that the

programme has been cancelled.

1. Turn on the water supply and check for leaks from fill hose.

2. Switch on the electricity supply.

3. Select spin programme 29 and then press the Start button to start the machine. Allow the

programme to continue for one minute and then cancel the programme (Please see

“description of controls” section for cancelling the programme). This will remove any water

remaining in the machine from factory testing.

4. To check for cold water filling to the machine:

Select a rinse programme and press the Start button to start the machine.

Allow the tumble action to continue until the water has pumped out.

Check that the drain outlet is not leaking or overflowing.

5. Switch off the machine at the end of the cycle by turning the control knob to the off position.

Installation testing is now complete.

To ensure the drum is thoroughly clean after testing and storage, select programme 2 and run

the machine for a complete cycle using only wash detergent and water.

If the machine is not to be used immediately, switch off the mains power supply and remove

the plug from the power socket. We also recommend that the water stop taps are turned off.

Note: it is advisable to isolate the washing machine from

the water and electricity supplies after each wash.

Note: it is advisable to turn off the tap after each wash

to isolate the washing machine from the water supply.

For the washing machine to function properly the terminal end of the discharge hose

(mouth) must be at a minimum of 50 cm and a maximum of 85 cm from the ground.

Electricity supply and safety advice

Washing machines are supplied to operate at a voltage of 230V, 50 Hz single-phase. Check

that the conductor is powerful enough to supply at least 3.0 kW, then connect the plug to a

10A earthed socket.

After installation,the appliance must be positioned so that the plug is accessible.

Check that the electricity supply to your home has an earthing system.

The socket in your home and the plug on the appliance must be of the same type.

It is generally not advisable to use multiple adapters and/or extension leads.

All Hoover washing machines comply with the safety requirements laid down by the Quality

Trademark Institute.

1110

When using your new Hoover Vision for the first time

Your new Vision washing machine incorporates highly sophisticated Inter@ct technology

which always ensures the best performance is achieved automatically. The Vision display

panel is a good example of Inter@ct technology as you can always see in plain English what

the machine is doing both before a wash programme (when you are setting the various

programmes and options) and during a cycle (when the display lets you see the stage the

cycle has reached). In this way, the Vision panel Inter@cts with you and really does serve as

your personal Washing Advice Centre.

This machine will operate prior to programming the Vision set up. However, this machine has

Start Delay and Programme End functions and for these functions to work efficiently the

Vision set must be programmed. This is a simple operation and special care has been taken

during manufacture to ensure that the user can operate this machine simply and effectively.

A quick guide around your Vision menu:

Connect product up to the electric / water supplies and drainage (see pag. 8).

Select any wash programme. After a short time a message will be displayed:

Note: The first message appear in German. See below for changing to English.

1312

HOOVER VISION

WILLKOMMEN! 11:05

accurate time can be reset later

1 KOCHWAESCHE

90° STARK 1600 UPM

this is displayed if prog. 1 is selected

CHOSEN LANGUAGE

ENGLISH

SET TIME MODE TO

ABSOLUTE

if RELATIVE is displayed press

“Extra rinse” (Extra spülgang)

(This changes a menu option)

Prior to entering the Vision pre set, remember time is limited while you decide on your options

(30 sec. / section). If you run out of time start from this point again.

Hold down at the same time the “Timer saver” (Express) and “Extra rinse” (Extra spülgang)

buttons for 5 sec. until screen changes to:

Press “Timer saver” (Express). This confirm and enters an option

Press “Timer saver” (Express)

ENABLE FINAL BLEEPING

YES

if NO is displayed press

“Extra rinse” (Extra spülgang)

Press “Timer saver” (Express)

SET NEW TIME

hh:

to change hours press the

“Extra rinse” (Extra spülgang) until correct

Press “Timer saver” (Express)

SET NEW TIME

mm:

to change mins press the

“Extra rinse” (Extra spülgang) until correct

PPress “Timer saver” (Express)

ENABLE MEMORY ?

YES

if NO is displayed press the

“Extra rinse” (Extra spülgang)

Press “Timer saver” (Express)

SET DEMO MODE ?

always select NO,

if YES press “Extra rinse” (Extra spülgang)

Press “Timer saver” (Express)

EXIT MENU?

YES

if NO is displayed press the

“Extra rinse” (Extra spülgang)

Press “Timer saver” (Express)

1 WHITE COTTON

90° HEAVY 1600 RPM

reverts back to the wash programme

selected

You are now able to select any wash programme. You can if you wish also set a delay start.

Where more detailed information is required refer to the relevant section from the following pages.

SPRACHE WAEHLEN

DEUTSCH

Press the “Extra rinse” button (Extra

spülgang) to change the language to

English.

A DETAILED GUIDE AROUND YOUR VISION MENU:

PROGRAMME END

AT 18.00 14:00

Therefore, when setting the Programme end time the programme (as shown above) will end

at 18.00.

The second way is if you wish programme end time or delay start to be programmed by

adding hours; e.g., programme to end in 1

hours. This is called Relative Time Mode.

When utilising the programme end function (or start delay), an example can be seen below

when the Relative Time Mode has been selected in the menu set-up stage.

Therefore, when setting the Programme end time the programme (as shown above) will end

at 15:30. (1h 30m after the current time, which is 14.00)

Both options are very useful, but we feel that the Absolute Time Mode will be more beneficial

and easier to use since there will be no need to calculate how many hours you will need to

leave before you want the machine to end or start.

On reaching the set time mode you will be asked if you would like to select “Relative” time or -

by scrolling through using the “Extra Rinse” button (Extra spülgang) - “Absolute” time.

Enter the preferred setting by pressing the “Timer saver” (Express) button.

When you have entered your preferred time-mode, the display will then ask for the Enable

Final Beeping to be set.

Enable Final Beeping (default setting - YES)

Here you have the option to have a beeping alarm to let you know the wash cycle has finished.

By pressing the “Extra Rinse” (Extra spülgang) button you can scroll through the “yes” and “no”

options.

To enter your selection press the “Timer saver” (Express) button and the screen will then

move to the next stage and ask you to “Set New Time”

Set New Time

This function needs to be set for two reasons: firstly to display the current time of day on the

screen and secondly for the programme end/delay start settings to work correctly.

You will notice in the display window that the hours on the clock will be flashing.

Set the hours by continually pressing the “Extra Rinse” (Extra spülgang) button and then

press the “Timer saver” button to input the hour of day.

Next the minutes on the clock will begin to flash, again press the “Extra rinse” button until the

required minutes are displayed and press “Timer saver” (Express) to input the selection.

When you have Set the New Time, the display will then ask if you wish to “Enable Memory”.

Enable Memory (default setting - NO)

This is a useful feature if you frequently wash laundry using the same programme.

Selecting “Enable Memory” will tell the machine to remember the last programme/functions

used and set them in the memory. This function works only on cottons, delicates, synthetics

and woollens programme (1÷23). The memory does not retain settings within the special

programme group.

Select “Yes” or “No” to this option by using the “Extra Rinse” (Extra spülgang) and “Timer saver”

(Express) button to input the selection.

The display will then shown a message that asks if you require demo mode to be set.

PROGRAMME END

BY 1H 30M 14:00

Programming the machine

Vision needs to be programmed so that the correct clock setting, language and personal

requirements are set. When the machine is turned on and the programme dial is moved away

from the “STOP” position to the programme selections a welcome message will appear.

This message is displayed for a short time while the machine recognises which programme

has been selected. When the machine is ready, the programme details will appear on the

display and from here you may now begin programming the machine.

Example

Enter the Menu

Prior to entering the Vision menu please note you have 30 seconds per operation to make

your selection. Should you run out of time the display will return to the start screen, and you

simply have to re-enter the Vision menu to continue with the programming.

From this stage the menu can be programmed. Hold down the “Timer saver” (Express) and

the “Extra Rinse” (Extra spülgang) buttons together for 5 seconds or until the beep sounds.

The menu options can be changed by pressing the “Extra Rinse” (Extra spülgang) button.

To confirm and enter an option press the “Timer saver” (Express) button.

Setting the language (default setting - GERMAN)

Your washing machine is automatically set to German.

Press the “Extra rinse” (Extra spülgang) button to change the language.

Press the “Timer saver” (Express) button to enter your selection.

When you have entered your chosen language, the display will then ask for the “Time-mode”

to be set.

Setting the time mode (default setting - ABSOLUTE)

There are two ways to select the time mode.

The first is if you wish programme end or delay start to be programmed by starting the actual

time you want the programme to end or begin, e.g., programme to end 18.00. This is called

Absolute Time Mode.

When utilising the programme end function (or start delay), an example can be seen below

when the Absolute Time Mode has been selected in the menu set-up stage.

HOOVER VISION

WELCOME 11.06

1 WHITE COTTON

90° HEAVY 1600 RPM

1514

This is the time of

day.

Description of controls

All of the buttons and dials on the washing machine control panel are listed below.

When you have selected the desired programme and any option buttons, the information you

have selected will appear on the screen in the Vision Inter@ct display panel.

When programmes and option buttons are compatible a bleeping sound will be heard and the

light above the option button selected remain illuminated. If you select an option button that is

not compatible with the programme you require, a buzzing sound will be heard and the button

light will not illuminate. To select an option button press it once in the lower side; to deselect

an option button, press it again.

Carefully read the relevant descriptions detailed below:

Programme Selector Dial

Rotates in both directions

Note: Do not press the start/pause button before

selecting the programme. If this does happen, cancel

the programme (that you have set accidentally) by

pressing the start/pause button for five seconds (See

programme cancelled description).

When you turn the programme selector dial and after the welcome message has

disappeared, you will see a display showing the following details:

Reading from left to right:

1. The programme number

2. The programme name

3. The wash temperature

4. The degree of soiling (how dirty the wash load is)

5. The spin speed

Example

1 WHITE COTTON

90° HEAVY 1600 RPM

Demo mode (default setting - NO)

Please set this option to “No” if not done so already - as this is for SERVICE use only.

If the demo mode option is set to “YES” when exiting the Vision menu the wash programme

WILL NOT commence. Demo Mode must be set at “NO” for the wash cycle to commence.

On entering “No” via the “Timer saver” (Express) button you will then be asked if you wish to

“Exit Menu”.

Exit Menu

If you are happy with the settings you have selected, you can now exit the menu by selecting

“Yes” via the “Extra Rinse” (Extra spülgang) and “Timer saver” (Express) button to input the

selection.

However, if you are not happy with any of the settings selected you must select “No” to the

exit menu command and you can then commence the programming from the beginning. By

pressing the “Timer saver” (Express) button you are able to enter and bypass each option

individually until you reach the option you would like to re-set.

When you are completely satisfied with your menu selection, you may exit the menu and

testing of the installation may now commence.

If, after the initial installation you may want to change any of the menu at a later date, again

run through the menu options from the beginning and change the options you want to reset.

This may be useful to change the “Set New Time” when the clocks go forward or back.

Once set, the menu options will remain in the memory of the machine even if the machine is

unplugged or if a power cut occurs.

1716

START/PAUSE Button

START

To start a programme press this button once. The door locked light will illuminate.

The machine will now be sensing the wash load and ask you to please wait.

Example

The Vision panel will after a short delay display the time to complete the programme and then

the wash cycle will commence. Vision calculates the time to the end of the selected

programme based upon a standard 5 kg load. During the cycle, Vision corrects the time to

that applicable to the size and composition of the load.

Example

This display also shows the current phase of the cycle and in the bottom right hand corner,

the current time is displayed.

This display will change throughout the wash programme as the cycle progresses.

PAUSE

The programme may be paused at any time during the wash cycle by holding down the

Start/Pause button for about two seconds and a beep will sound. A message will appear on

the display to inform you that the programme has been paused. To restart the programme

press the Start/Pause button once again. The display will inform you that the programme will

continue.

Example

SETTING WASHING

PARAMETERS: PLS WAIT

TIME TO END 1H:50M

WASHING 19:30

COLOURFAST COTTON

PROGRAMME PAUSED

PROGRAMME CANCELLED

Note

After cancelling a programme it’s possible to drain the water from the

drum using the spin programme N° 29.

CANCEL

To cancel the programme the Start/Pause button must be pressed down for 5 seconds until the

beep sounds. The display will inform you that the display has been paused and has then been

cancelled.

Example

18 19

DOOR HANDLE

Press the finger-bar inside

the door handle to open the door

Door open: Aspecial safety device prevents the door from being opened immediately

after the end of the cycle. “Door locked” indicator light is illuminated when the door is fully

closed. Wait for 2 minutes after the wash cycle has finished before opening the door. The

door locked neon will go out and the door may be opened. As a safety measure check that

there is no water evident in the drum.

BIG WASH LOAD button (MAXI BELADUNG)

Hoover has designed a special wash boost system specially for big loads - by selecting this

button, (available on programmes 1 ÷ 11) the volume of water within the selected wash cycle

is increased and the length of time of the programme is extended to improve the wash

performance for the bigger load.

TIMER SAVER button (EXPRESS)

This option can be utilised on cotton and synthetic programmes (1 ÷ 17). By selecting the

Timer saver option, the wash time may be reduced by up to 50 minutes, depending on the

programme selected.

PRE-WASH button (VORWÄSCHE)

This option (available on programmes 1÷17) is particularly useful for heavily soiled loads and

can be used before selecting the main wash programme. Detergent for this programme

should be added to the first compartment of the soap drawer labelled “I” (Please refer to

Detergent Drawer Section of manual). We recommend you use only 20% of the

recommended quantities shown on the detergent pack and fabric conditioner should not be

used for this programme.

EXTRA RINSE button (EXTRA SPÜLGANG)

This option (not available for wool programmes) adds more water at the rinsing stage. This

can help prevent skin irritation from detergent residue for people with particularly sensitive

skin. Selecting the Extra Rinse button is also recommended when washing heavily soiled

fabrics which need a lot of detergent, or when the wash load contains towelling fabrics that

have a greater tendency to retain detergent.

FAST IRON Button (LEICHTBÜGELN)

This option is available on Resistant, Synthetics, Delicates, Woollens and some

Special Programmes (excluding programmes 26-29). When this option is selected for

Resistant, Delicates, Woollens or Handwash programmes the machine will stop and the load

will be held within the water in the drum.

This reduces the creasing thus enabling easier ironing. To continue with the wash cycle the

Fast Iron button must be pressed and the programme will re-start. With the Fast Iron option

selected within the synthetics cycle the programme is completed by a short, very low speed

spin. The laundry may be left in the drum in this condition without the risk of excessive

creasing. If a fuller spin cycle is required select the appropriate spin (see Programme Guide)

and then remove the laundry on completion of the programme.

Note: This model is fitted with an electronic “sensor”

device that checks the load is balanced correctly. If the

load is slightly unbalanced the machine will re-balance

it automatically to then carry out the normal spin.

If, after several attempts, balance is not restored a

reduced spin speed will be used. If loads are seriously

unbalanced the spin stage will be cancelled.

This helps limit vibration, reduce noise and improve

the washing machine’s reliability and life.

SELECT SPIN button (SCHLEUDERN)

On selecting the wash programme the display will inform you of the maximum

spin speed permitted for that programme. By repeatedly pressing the select spin button the

speed will decrease by increments of 100 rpm. The minimum speed permitted is 400 rpm, or

by continuously pressing the select spin option the spin may be cancelled if desired.

On selecting the required spin speed the display will then inform you of the chosen

programme, its temperature and the newly selected spin speed.

The machine makes a different noise when spinning! This is

because it has a manifold motor for better performance.

CHILD LOCK button (KINDERSICHERUNG)

This is a useful feature to prevent children playing with the option buttons and tampering

with the programme you have set.

After you have set the programme and option buttons you require, press start

and then Child Lock. This “locks” the control panel.

You may cancel this function by pressing the child lock button briefly until you see the

light above the button flash. While this light is flashing, press the “Fast Iron” button – the

display will inform you that the options are no longer locked and further changes can now be

made.

DELAY START/SET END TIME

(STARTZEIT-VORWAHL/ENDZEIT WÄHLEN)

The programme end time/delay start options can be used if you want the washing to be ready

at a later time (but within 24 hours).

NOTE: After selected the programme END TIME/DELAY START press the start button.

1. DELAY START

After selecting the programme, press delay start/set end time button once and press the

hours and minutes buttons (to the left and right) until the required time is set. The display

returns to the programme option if the button is pressed within 5 seconds.

To cancel delay start, hold down the button for 5 seconds.

2. SET END TIME

Press delay start/set end time button twice and press the hours and minutes buttons (to the

left and right) until the required time is set. When entering the programme end option, the

display will show the minimum time which you can set the programme to end by. This time

may only be extended as you require.

NOTE: When using the delay start/set end time functions, only use detergents and laundry

also via the dispenser drawer. Adding detergents etc. to the drum and then leaving them to

stand for long period of time may damage your laundry.

It is unlikely that water will be visible in the drum!

This is due to the latest technology that achieves the

same standard of washing and rinsing but with far less

water consumption.

Detergents, washing aids and amounts to use

Choice of detergent

General purpose detergents

– Powder detergents, for a thorough wash, with bleaching agent, particularly suitable for

use in hot wash programmes (60°C and over), for heavily soiled and stained laundry.

– Liquid detergents, particularly suitable for grease stains, such as greasy skin marks,

cosmetics and oil.

–These detergents are not suitable for washing stained laundry, as they do not contain

bleach.

– Biological detergents, not all the products available give a really through wash.

Special detergents

– Detergents for coloureds and delicates, without added bleach, also often without any

optical brightening agents, to preserve the colour.

– Detergents for a thorough wash, without added bleach or enzymes, particularly suitable

for handling woollen fibres.

– Detergents for curtains with optical brightening agents, resistant to light, to prevent

yellowing from sunlight.

– Special detergents for programmed use of chemical substances, depending on fabric

type, degree of soiling and water hardness.

Here basic detergents, softeners, bleaches/stain removers can be added separately.

Additional laundry aids

– Water softener, means less detergent can be used where water hardness is classed as

hard to very hard.

– Prewash substances, for the programmed treatment of stains prior to the main wash.

Using them means the subsequent wash can be at a low temperature or with bleach-free

detergents.

– Fabric softener, prevents static build-up in synthetic fabrics and softens fabrics.

If you own a tumble dryer, clothes are softened even without the use of a fabric softener.

Do not put solvents in the washing machine!

Keep detergents and other laundry products out of children’s reach.

Before pouring in the detergent check that there are no foreign bodies in the detergent

drawer.

Dosage details are usually shown on the detergent packaging. Follow those instructions.

Detergent drawer

The detergent drawer is divided into 3 compartments:

–the first, labelled «I», is for detergent utilised during

Prewash

–the second, labelled «II», is for detergent for main

wash

Note: Some detergents are difficult to remove. For

these, we recommend you use the special dispenser

which is placed in the drum.

–the third, labelled “ ” is for special additives, fabric softeners, fragrances, starch,

brighteners etc.

Note: only put liquid products in the third compartment.

The machine is programmed to automatically take up additives during the final rinse stage for

all wash cycles.

Programme selector

The washing machine has 5 different programme groups according to type of wash,

temperature, spin speeds and duration for handling the various types of fabric and their level

of soiling (see wash programme guide on page 30-31).

1. COTTONS

The programmes are designed for maximum washing and rinsing. With spin cycles in

between, they guarantee the laundry is rinsed perfectly. The final spin cycle ensures laundry

is spun dry as much as possible up to the maximum speed.

2. SYNTHETICS and mixed fabrics

Washing and rinsing performance is optimised through drum rotation speeds and water

levels. The delicate action spin minimises creasing.

3. DELICATES

This is a new concept in washing, with a cycle that comprises of alternate periods of activity

and pauses, particularly suitable for washing very delicate fabrics.

Wash and rinsing are carried out using a high water level to provide the best results.

4. WOOLLENS

The programmes are designed for maximum washing at the temperature most suitable to

your woollen garments and their degree of soiling. Always read the wash advice label for the

most suitable temperature.

5. SPECIAL PROGRAMMES - 29 minute Speed Wash, Handwash and Sportswear

SPORTSWEAR

The washing machine has a unique Sportswear programme (programme 24). It is specially

designed to wash mixed sportswear fabrics that cannot be washed on hotter programmes

and is designed to remove the soil and staining created by participation in sports activities.

This programme starts with a cold prewash that breaks down and loosens any excess dirt

and then washes at a cool 30°C, rinses and spins slowly for the best care of your heavily

soiled, delicate garments.

Hoover has given sports items their own wash care programme.

HAND WASH

This washing machine also has a gentle Hand Wash programme cycle (programme 25). This

programme allows a complete washing cycle for garments specified as “Hand Wash only” on

the fabric care label. The programme has a maximum temperature of 30° C and concludes

with 2 rinses, one for fabric conditioner and a slow spin.

SPEED WASH

This washing machine also has a SPEED WASH programme option (Programme 26). This

programme allows a complete washing cycle to be carried out in approximately 29 minutes,

with a maximum load of 2 kg and is recommended for lightly soiled items. When selecting the

Speed Wash programme, please note that we recommend you use only 20% of the

recommended quantities shown on the detergent pack.

Dosages

Only use detergents which are suitable for use in a washing machine.

You will obtain the best results from your wash with the minimum use of chemical products

and the best care for your laundry if you take into consideration the degree of soiling as well

as the type of detergent to choose.

The amount of detergent to use depends on:

– water hardness, depending on the hardness of the water and the type of detergent used,

it is possible to reduce the amount of detergent.

– the degree of soiling, it is possible to reduce the amount of detergent used depending on

the degree of soiling.

– amount of laundry, it is possible to reduce the amount of detergent when washing only a

small amount of laundry.

The amounts shown on pack for detergents for washing delicates often already refer to a

reduced wash size.

Follow the dosage instructions!

Dosage for powder detergent

For normal and low concentration detergents: for normally soiled laundry choose a

programme without prewash.

Put the detergent in compartment II of the drawer.

For heavily soiled laundry, choose a programme with prewash.

Put

⁄

of the detergent in compartment I,

in compartment II of the drawer.

When using water softeners, first put in the detergent, then add the softener to compartment II.

For highly concentrated detergents not in single dose format, follow what is shown on pack

exactly as regards type and amount of dosage.

To avoid the difficulty of checking if the detergent has been taken up, use the dosage aids

provided in the detergent packaging.

Liquid detergent dosage

Liquid detergents may be used in accordance with the instructions on the relevant packaging,

for all programmes without prewash, by using the special container which is placed in the

drum or, for those models that have it, in the special insert for liquid detergents.

Main wash

Sorting the laundry

– It is recommended you wash only items which are washable with water and detergent and

not dry-clean items.

– If you need to wash rugs, bedspreads or other heavy items, it is best not to spin them.

–Sort the laundry according to fabric type, degree of soiling and wash temperature: follow

the labelling in the garments.

Laundry for hot wash

Coloured, easy-care materials

Delicates and wool

Wash by hand

– Items labelled with the following symbols are not suitable for machine washing:

Dry clean

For very delicate items, such as net curtains, underwear, tights etc., you are advised to

use a laundry net or wash bag.

–Woollen items must be labelled with the «Pure New Wool» symbol to be washed in the

machine , and must also be labelled «non-matting» or «machine washable».

–Colour often leaks from new coloured items.

This can then colour other lighter items being washed.

We therefore recommend that coloured items should be washed for the first time separately.

For future washes, colourfast items can only be washed with white laundry up to 40°C.

60 50 40

Auto Half Load

The washing machine is fitted with a self adjusting water level system.

This system enables the machine to use only the right amount of water needed to wash and

rinse the laundry in relation to the particular load.

This results in a reduction of the water and electricity used, without in any way

compromising the washing and rinsing performance.

In fact the amount of water and electricity used will always be appropriate for the clothes load.

The washing machine automatically ensures excellent washing results at minimum cost whilst

respecting the environment .

WHISPER

With Vision,Hoover has made a technology breahthrough by featuring the “WHISPER”

system for extra-quiet washing.

The mission of the New Vision featuring WHISPER is to improve your quality of life.

A number of very important modifications have been introduced to develop WHISPER:

7 sound absorbing panels on the sides of the machine, a sheet of corrugated material on the

bottom, complete soundproofing of the motor, tub made of sound absorbing material

(Silitech).

WHISPER means greater efficiency than other similar, non-soundproofed machines.

Atechnical analysis of the European market reveals that the new Hoover Vision featuring

WHISPER is among the quietest available.

Selecting the wash programme

Refer to the programme guide or the programme descriptions on the front of the machine to

select the most suitable programme.

The programme is selected by turning the programme selector clockwise and aligning the

programme number with the indicator .

Check that the tap is turned on and that the discharge hose is positioned correctly.

Press additional function buttons if you require.

Press the start button. The door locked indicator illuminates and the programme will begin.

When the programme has finished

–the door lock light is lit and the display will read “Door lock activated please wait to open”.

–the door lock light goes out (door lock released) and the display will read “Programme

complete unload the laundry”.

– Switch off the machine by turning the control knob to the off position.

–Open the door and remove the laundry.

Disconnect the plug from the mains power supply and turn off the water supply after every use.

Note: when sorting laundry

–check there are no metal objects in the laundry

(such as paper clips, safety pins, pins, coins

etc...);

–In the event of a machine failure during the

warranty period and foreign objects are found to

be the cause of the failure a labour charge may be

made to call out an engineer.

– button up pillowcases, fasten zips, hook & eye

fasteners, belts and long dressing gown cords;

–remove curtain hooks;

– pay close attention to the labels on items

–if you notice stubborn stains whilst sorting the

laundry, remove them using a special detergent or

a special stain remover.

–We recommend that you do not wash a full load of just towelling items as these can

become too heavy since they absorb a lot of water, possibly resulting in a load which is

out of balance (see page 21).

The correct way to wash

Preparing the laundry

A) Select and sort the laundry according

to the wash care labels found

on each garment. Always check the care labels.

Loading the laundry

B) Open the door.

C) Put the laundry in the washing machine.

Close the door again, ensuring that no items of

laundry are obstructing the lock, or door seal.

Putting detergent in machine

D) Open the drawer, choose the detergent and put in

the correct amount, according to the manufacturer’s

instructions and the advice on page 23.

Add any other laundry aids (see page 23). Close the

drawer again.

Liquid detergents that are to be placed directly into the

drum should use the recommended dispensing device.

Programme guide

PROGRAMME

Acrylics

Synthetics (Nylon)

Coloured mixed fabrics

Normal-Light

soiling

230°

●●●

Acrylics

Synthetics (Nylon)

Coloured mixed fabrics

Normal-Light

soiling

15°

(cold)

●●●

Delicates

Delicates Synthetics

& mixed fabrics

Light soiling

Delicate fabrics

1,5 40°

●●

Delicates

Delicates Synthetics

& mixed fabrics

Light soiling

Delicate fabrics

1,5 30°

●●

Delicates

Delicates Synthetics

& mixed fabrics

Light soiling 1,5

15°

(cold)

●●

Woollens

Machine washable

Wool ,

very delicate fabrics,

synthetic

knits

Normal soiling 1 40°

●●

Woollens Light soiling 1 30°

●●

Woollens Light soiling 1

15°

(cold)

●●

Special:

Sportswear

Mixed fabrics

Thorough wash

for small loads

230°

●●

Special:

Hand Wash

Mixed fabrics “Hand

Wash only” garments

Hand washing of

delicate garments

130°

●●

Special:

Speed Wash

Mixed fabrics

Rapid wash for lightly

soiled garments

250°

●●

Rinse & Wool

Spin

Delicate fabrics

& wool

Rinse &

Wool rinse

●

Last Rinse

& Spin

Mixed fabrics

Last Rinse & Spin

●

Spin

Mixed fabrics

High Speed Spin

FABRIC TYPE PROGRAMME FOR LOAD

WATER

TEMP.

°C

DETERGENT

III

Points to consider: When washing heavily soiled laundry it is recommended the load is reduced

by about 1-1.5 kg. By doing so the laundry is allowed to circulate more freely.

Energy label data based on programme 2 tested in accordance with EN60456.

If the pre-wash button is pressed.

❀

Programme guide

PROGRAMME

Resistant

cotton

Colourfast fabrics

Cotton, linen, hemp

Intensive - heavily

soiled

590°

●●●

Resistant

cotton

Cotton, mixed fabrics

Colour Fast

Intensive - heavily

soiled

560°

●●●

Resistant

cotton

Cotton, mixed fabrics

Colour Fast

Intensive - heavily

soiled

550°

●●●

Resistant

cotton

Cotton, mixed fabrics

Colour Fast

Intensive - heavily

soiled

540°

●●●

Colour

cotton

Cotton, mixed fabrics

Colour Fast

Normal-Light soiling 5 60°

●●●

Colour

cotton

Cotton, mixed fabrics

Colour Fast

Normal-Light soiling 5 50°

●●●

Colour

cotton

Cotton, mixed fabrics

Colour Non Fast

Normal-Light soiling 5

40°

●●●

Colour

cotton

Cotton, mixed fabrics

Colour Non Fast

Normal-Light soiling 5 30°

●●●

Delicate

colour

Cotton, mixed fabrics

Colour Non Fast

Lightly soiled - delicate

coloureds

540°

●●●

Delicate

colour

Cotton, mixed fabrics

Colour Non Fast

Lightly soiled - delicate

coloureds

530°

●●●

Delicate

colour

Cotton, mixed fabrics

Colour Non Fast

Lightly soiled - delicate

coloureds

15°

(cold)

●●●

Synthetics

Mixed synthetic fabrics

Colour Fast mixed fabrics

Heavily soiling 2 60°

●●●

Synthetics

Mixed fabrics,

Cotton, synthetics

Heavily soiling 2 50°

●●●

Synthetics

Mixed fabrics,

Cotton, synthetics

Heavily soiling 2 40°

●●●

Acrylics

Synthetics (Nylon)

Coloured mixed fabrics

Normal-Light

soiling

240°

●●●

FABRIC TYPE PROGRAMME FOR LOAD

WATER

TEMP.

°C

DETERGENT

❀

Transporting/Storing the appliance

for long periods when appliance

is not in use

If the appliance is being transported or is out of use for

long periods in unheated places, all remaining water

must be completely removed from all hoses.

Ensure mains power is off, then unclip the hose and

point it downwards into a basin until all the water has

emptied out.

When finished, repeat the operation in the reverse order.

Cleaning and routine maintenance

Do not use alcohol-based scourers and /or thinners on the outside of your washing machine,

just a wipe with a damp cloth will suffice. The washing machine needs very little maintenance:

–Cleaning the drawer compartments.

–Cleaning the filter.

Cleaning the drawer compartments

Even if it is not strictly necessary, it is advisable to clean

the compartments for bleaching detergents and additives

occasionally.

A) To do this you just need to pull them out firmly, but

without forcing them.

B) Clean everything in the compartment under running water.

C) Put everything back in its proper place.

Cleaning the filter

The washing machine is fitted with a special filter for

handling large deposits which could block the discharge

hose (coins, buttons etc.) and which can, therefore, be

easily retrieved.

The cleaning operation is as follows:

1. Open the lid as shown in fig.

2. Turn the filter anticlockwise until it stops, remove it

and clean it.

3. After cleaning it, reassemble it following the previous

instructions in reverse order.

4. Close the lid.

Attention: if the filter needs

cleaning while there is washing

still in the drum, follow the

instructions on the following page

to empty the water. This will

prevent excessive loss of water

via the filter.

3332

Note:

The use of environmentally-friendly, phosphate-free detergents (check detergent information

on pack) can have the following effects:

–waste water from rinsing may be cloudier because of the presence of a white powder

(zeolites) held in suspension, without the rinse performance being adversely affected;

–presence of white powder on laundry after washing, which is not absorbed by the fabric

and does not alter the colour of the fabric.

–The presence of foam in the final rinsing water is not necessarily an indication of poor rinsing.

–Carrying out more rinse cycles does not serve any purpose in such cases.

It is unlikely that water will be visible in the drum!

This is due to the latest technology that achieves the

same standard of washing and rinsing but with far less

water consumption.

Important: the water may be very hot!

Power failure

If there is a power failure the wash cycle will be interrupted, the wash programme and

functions will be suspended. When the power is restored, the wash programme and functions

will re-start from the same point and complete the programme.

The load can be removed from the machine during a power failure as follows:

The water can be drained from the machine by:

1. Switch off the machine by the programme dial and at the mains power supply.

Remove the plug from the mains power supply socket.

2. Carefully move the machine so the rear of the machine is accessible. Please follow the

safety precautions which we recommend under the “safety notes” section of this manual.

3. Unclip the drain hose from the rear panel of the machine and lower the hose into a bowl on

the floor.

When the bowl is full raise the end of the drain pipe to a height higher than the top of the

appliance to stop the flow of water. Empty and replace the bowl and continue draining the

machine until empty.

Trouble shooting

What might be the cause of…

Defects you can remedy yourself

Before calling GIAS Service for technical advice please run through the following checklist. A

charge will be made if the machine is found to be working or has been installed incorrectly or

used incorrectly.If the problem persists after completing the recommended checks, please call

the GIAS Service, they may be able to assist you over the telephone.

CAUSE REMEDYPROBLEM

Plug not in socket.

Not switched on.

Power failure.

Fuse blown.

Door open.

RCD tripped (trip switch)

Has the Delay start been set.

Plug it in.

Switch on.

Check and refer to “Power Failure” section.

Check.

Close door.

Reset RCD.

Check.

1. Does not work on any

programme

See cause 1.

Water supply turned off.

Programme selector not correctly positioned.

Check.

Turn on water supply.

Position programme selector correctly.

2. Does not fill with water

Kink in discharge hose.

Foreign bodies in filter

The machine has been plumbed in incorrectly.

Straighten discharge hose.

Examine filter.

Check installation.

3. Water does not drain away

Leaking gasket between tap and water inlet hose.

Strand of clothing or dirt between door rubber

gasket and door glass.

Incorrect plumbing.

Replace gasket and tighten connection.

Re-load the machine and keep rubber door

gasket/door glass clean.

Check plumbing.

4. Water on floor around the

washing machine

Water has not yet drained away.

“Spin Cancel” option selected

(certain models only).

Unbalanced load.

Wait a few minutes for machine to empty.

Check.

Rearrange load evenly.

5. Does not spin

Washing machine not completely level.

Load not distributed evenly.

Transit brackets not removed.

Adjust the special adjustable feet.

Rearrange the laundry evenly.

Remove transit brackets (

see installation section

6. Machine vibrates a lot

during spin

Two minutes have not elapsed since the

programme finished.

–

No water fill.

No pump out.

Wait two minutes.

Call service.

Check water supplies are on.

Check drain is clear.

Check drain hose is not kinked.

7. Door will not open

8. Display reads error

0, 1, 5, 7, 8, 9

9. Display reads error 2

10. Display reads error 3

Machine overfilled with water. Turn off water supply to machine.

Call service.

11.Display reads error 4

3534

The machine makes a different noise when spinning! This is

because it has a manifold motor for better performance.

Appliance complies with European Directive 89/336/EEC, 73/23/EEC and subsequent

amendments.

Technical data

■

Max. load of dry laundry

■

Water pressure

■

Spin Speed

Measurements

■

Width

■

Depth

■

Height

NB: For specifications regarding electrical data, see the data panel on the front of the washing

machine (porthole area).

5 kg

(0,5 ÷ 8 bar)

0,05 ÷ 0,8 MPa

1600 r.p.m.

60 cm

61 cm

85 cm

Fig. 1

The manufacturer declines all responsibility in the event of any printing mistakes in

this booklet. The manufacturer also reserves the right to make appropriate

modifications to its products without changing the essential characteristics.

Customer Service

The appliance is covered by a certificate of guarantee which allows you free use of the

Hoover Technical Support Service, except for the price of the call, for a period of one year

from the date of purchase. Remember to send off the guarantee certificate for validation

within 10 days of the date of purchase.

You should retain the receipt issued by the retailer when you purchased the machine to show

to the call out engineer, should you need to consult one.

If your washing machine shows signs of a defect or is not working properly, before you

contact GIAS Service we recommend you carry out the checks detailed on page 34 within the

Trouble shooting section.

If the problem with the machine persists after completing all the recommended checks,

please dial the GIAS Service number on the rear cover of this manual.

For the cost of a telephone call, you will be connected directly to GIAS. It is important you tell

the GIAS advisor your product’s model number and serial number, which you will find on the

rating label (16 characters, beginning with the number 3), found on the front of the washing

machine (door area). By doing this, your enquiry will be responded to more efficiently.

Important: the water and the load may be very hot!

4. Once the machine is fully drained of water, clip the hose to the rear of the machine. Press

the door open button and remove the load.

The door can be opened approximately 2 minutes after the power failure by simply pressing

the door open button. Do not force open the door.

Indice Pagina

Introduzione 40

Note generali alla consegna 41

Prescrizioni di sicurezza 41

Guida rapida 42

Installazione e collaudo 43

Informazioni utili per il lavaggio 48

Utilizzo di Vision per la prima volta 49

Descrizione dei comandi 54

Cassetto del detersivo 59

Detersivi, additivi e dosaggi 60

Selettore programmi 62

Riduzione automatica dei consumi 63

Super Silent 63

Il lavaggio 64

Guida ai programmi 66

Pulizia e manutenzione ordinaria 68

Ricerca guasti 70

Interruzione di corrente 71

Dati tecnici 72

3938

Selettore programmi

Tasto Avvio/Pausa

Maniglia apertura oblò

Pulsante “Extra carico”

Pulsante “Lavaggio rapido”

Pulsante “Pre lavaggio”

Pulsante “Extra risciacquo”

Pulsante “Giri centrifuga”

Pulsante “Blocco tastiera”

Pulsante “Partenza programmata/Regolazione fine ciclo”

Pulsante “Stiro facile”

Cassetto detersivo

Descrizione comandi

DEFGH I LM B

La pagina sta caricando ...

Hoover LBHVP16ALUDE Manuale utente

Marca: Hoover

Modello: LBHVP16ALUDE

Categoria: Lavatrici

Tipo: Manuale utente

Questo manuale è adatto anche per

Scarica il pdf

rapporto

Hoover LBHVP16ALUDE Manuale utente

Questo manuale è adatto anche per

Hoover LBHVP16ALUDE Manuale utente

Documenti correlati

Altri documenti