Yamaha RX-V757 Manuale utente

Categoria
Ricevitori AV
Tipo
Manuale utente
YAMAHA ELECTRONICS CORPORATION, USA
6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD.
135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H.
SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A.
RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD.
YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B.
J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD.
17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
©
2005 All rights reserved.
RX-V757
Printed in Malaysia WE59930
RX-V757
AV Receiver
OWNER’S MANUAL
U
01EN_RX-V757_U-cv_version1.fm Page 1 Friday, December 24, 2004 4:29 PM
IMPORTANT SAFETY INSTRUCTIONS
i
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert you to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle
is intended to alert you to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
1 Read Instructions – All the safety and operating instructions
should be read before the product is operated.
2 Retain Instructions – The safety and operating instructions
should be retained for future reference.
3 Heed Warnings – All warnings on the product and in the
operating instructions should be adhered to.
4 Follow Instructions – All operating and use instructions
should be followed.
5 Cleaning – Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners. Use
a damp cloth for cleaning.
6 Attachments – Do not use attachments not recommended by
the product manufacturer as they may cause hazards.
7 Water and Moisture – Do not use this product near water –
for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a swimming pool;
and the like.
8 Accessories – Do not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may fall,
causing serious injury to a child or adult, and serious
damage to the product. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer, or sold
with the product. Any mounting of the product should
follow the manufacturer’s instructions, and should use a
mounting accessory recommended by the manufacturer.
9 A product and cart combination should be moved with care.
Quick stops, excessive force, and uneven
surfaces may cause the product and cart
combination to overturn.
10 Ventilation – Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of the
product and to protect it from overheating, and these
openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should not
be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
11 Power Sources – This product should be operated only from
the type of power source indicated on the marking label. If
you are not sure of the type of power supply to your home,
consult your product dealer or local power company. For
products intended to operate from battery power, or other
sources, refer to the operating instructions.
12 Grounding or Polarization – This product may be equipped
with a polarized alternating current line plug (a plug having
one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you
are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the polarized plug.
13 Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and the
point where they exit from the product.
14 Lightning – For added protection for this product during a
lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line
surges.
15 Power Lines – An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be
fatal.
16 Overloading – Do not overload wall outlets, extension
cords, or integral convenience receptacles as this can result
in a risk of fire or electric shock.
17 Object and Liquid Entry – Never push objects of any kind
into this product through openings as they may touch
dangerous voltage points or short-out parts that could result
in a fire or electric shock. Never spill liquid of any kind on
the product.
18 Servicing – Do not attempt to service this product yourself
as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
19 Damage Requiring Service – Unplug this product from the
wall outlet and refer servicing to qualified service personnel
under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the
product,
c) If the product has been exposed to rain or water,
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPORTANT SAFETY INSTRUCTIONS
ii
EXAMPLE OF ANTENNA GROUNDING
MAST
GROUND
CLAMP
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810–20)
GROUNDING CONDUCTORS
(NEC SECTION 810–21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
ELECTRIC
SERVICE
EQUIPMENT
NEC – NATIONAL ELECTRICAL CODE
d) If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to its normal
operation,
e) If the product has been dropped or damaged in any
way, and
f) When the product exhibits a distinct change in perfor-
mance - this indicates a need for service.
20 Replacement Parts – When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other
hazards.
21 Safety Check – Upon completion of any service or repairs to
this product, ask the service technician to perform safety
checks to determine that the product is in proper operating
condition.
22 Wall or Ceiling Mounting – The unit should be mounted
to a wall or ceiling only as recommended by the
manufacturer.
23 Heat – The product should be situated away from heat
sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
24 Outdoor Antenna Grounding – If an outside antenna or
cable system is connected to the product, be sure the antenna
or cable system is grounded so as to provide some
protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA 70,
provides information with regard to proper grounding of the
mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and, in particular, specifies
that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as
practical.
FCC INFORMATION (for US customers)
1 IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
2 IMPORTANT: When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product MUST
be used. Follow all installation instructions. Failure to
follow instructions could void your FCC authorization to
use this product in the USA.
3 NOTE: This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15
for Class “B” digital devices. Compliance with these
requirements provides a reasonable level of assurance that
your use of this product in a residential environment will
not result in harmful interference with other electronic
devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions found
in the users manual, may cause interference harmful to the
operation of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this
product is found to be the source of interference, which
can be determined by turning the unit “OFF” and “ON”,
please try to eliminate the problem by using one of the
following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
iii
1 To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2 Install this sound system in a well ventilated, cool,
dry, clean place – away from direct sunlight, heat
sources, vibration, dust, moisture, and/or cold.
Allow ventilation space of at least 30 cm on the top,
20 cm on the left and right, and 20 cm on the back of
this unit.
3 Locate this unit away from other electrical
appliances, motors, or transformers to avoid
humming sounds.
4 Do not expose this unit to sudden temperature
changes from cold to hot, and do not locate this unit
in a environment with high humidity (i.e. a room with
a humidifier) to prevent condensation inside this
unit, which may cause an electrical shock, fire,
damage to this unit, and/or personal injury.
5 Avoid installing this unit where foreign object may
fall onto this unit and/or this unit may be exposed to
liquid dripping or splashing. On the top of this unit,
do not place:
Other components, as they may cause damage
and/or discoloration on the surface of this unit.
Burning objects (i.e. candles), as they may cause
fire, damage to this unit, and/or personal injury.
Containers with liquid in them, as they may fall
and liquid may cause electrical shock to the user
and/or damage to this unit.
6 Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If
the temperature inside this unit rises, it may cause
fire, damage to this unit, and/or personal injury.
7 Do not plug in this unit to a wall outlet until all
connections are complete.
8 Do not operate this unit upside-down. It may
overheat, possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cord from the wall
outlet, grasp the plug; do not pull the cord.
11 Do not clean this unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used.
Using this unit with a higher voltage than specified
is dangerous and may cause fire, damage to this
unit, and/or personal injury. YAMAHA will not be
held responsible for any damage resulting from use
of this unit with a voltage other than specified.
13 To prevent damage by lightning, disconnect the
power cord and outdoor antenna from the wall outlet
during an electrical storm.
14 Do not attempt to modify or fix this unit. Contact
qualified YAMAHA service personnel when any
service is needed. The cabinet should never be
opened for any reasons.
15 When not planning to use this unit for long periods
of time (i.e. vacation), disconnect the AC power plug
from the wall outlet.
16 Be sure to read the “TROUBLESHOOTING” section
on common operating errors before concluding that
this unit is faulty.
17 Before moving this unit, press STANDBY/ON to set
this unit in the standby mode, and disconnect the
AC power plug from the wall outlet.
18 VOLTAGE SELECTOR (Asia and General models
only)
The VOLTAGE SELECTOR on the rear panel of this
unit must be set for your local main voltage BEFORE
plugging into the AC main supply. Voltages are:
Asia model ..................... 220/230–240 V AC, 50/60 Hz
General model
........................... 110/120/220/230–240 V AC, 50/60 Hz
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association’s Consumer
Electronics Group want you to get the most out of your equipment
by playing it at a safe level. One that lets the sound come through
loud and clear without annoying blaring or distortion – and, most
importantly, without affecting your sensitive hearing.
Since hearing damage from loud sounds is often
undetectable until it is too late, YAMAHA and the
Electronic Industries Association’s Consumer
Electronics Group recommend you to avoid
prolonged exposure from excessive volume levels.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
This unit is not disconnected from the AC power
source as long as it is connected to the wall outlet,
even if this unit itself is turned off. This state is called
the standby mode. In this state, this unit is designed to
consume a very small quantity of power.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to
wide slot and fully insert.
This Class B digital apparatus complies with Canadian
ICES-003.
IMPORTANT
Please record the serial number of this unit in the space
below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
1
PREPARATIONINTRODUCTION
BASIC
OPERATION
SOUND FIELD
PROGRAMS
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
FEATURES............................................................. 2
GETTING STARTED............................................ 3
Supplied accessories.................................................. 3
Installing batteries in the remote control................... 3
CONTROLS AND FUNCTIONS ......................... 4
Front panel................................................................. 4
Remote control...........................................................6
Using the remote control ........................................... 7
Front panel display ....................................................8
Rear panel................................................................10
SPEAKER SETUP ............................................... 11
Speaker placement................................................... 11
Speaker connections ................................................ 12
CONNECTIONS .................................................. 15
Before connecting components................................15
Connecting video components................................. 16
Connecting audio components................................. 19
Connecting the FM and AM antennas..................... 21
Connecting the power supply cord .......................... 22
Speaker impedance setting ...................................... 23
Turning on the power............................................... 23
AUTO SETUP....................................................... 24
Introduction.............................................................. 24
Optimizer microphone setup.................................... 24
Starting the setup ..................................................... 25
PLAYBACK.......................................................... 30
Basic operations....................................................... 30
Selecting sound field programs ............................... 32
Selecting input modes.............................................. 37
FM/AM TUNING................................................. 39
Automatic and manual tuning.................................. 39
Presetting stations.................................................... 40
Selecting preset stations........................................... 42
Exchanging preset stations ...................................... 43
XM SATELLITE RADIO TUNING .................. 45
What is XM Satellite Radio?...................................45
XM Satellite Radio connections..............................45
XM Satellite Radio functions .................................. 46
Activating XM Satellite Radio ................................47
Basic XM Satellite Radio operations.......................48
XM Satellite Radio search modes............................ 49
Setting XM Satellite Radio preset channels ............52
RECORDING....................................................... 55
SOUND FIELD PROGRAM
DESCRIPTIONS...............................................56
For movie/video sources.......................................... 56
For music sources.................................................... 58
ADVANCED OPERATIONS ..............................59
Selecting the OSD mode.......................................... 59
Using the sleep timer............................................... 59
Manually adjusting speaker levels........................... 60
SET MENU............................................................61
Using SET MENU................................................... 63
1 SOUND MENU.................................................... 64
2 INPUT MENU...................................................... 69
3 OPTION MENU................................................... 71
ADVANCED SETUP MENU...............................73
REMOTE CONTROL FEATURES ...................75
Control area ............................................................. 75
Setting remote control codes ................................... 76
Controlling other components ................................. 78
Programming codes from other remote controls..... 79
Changing source names in the display window....... 80
Clearing function sets.............................................. 81
Clearing individual functions .................................. 82
ZONE 2 (U.S.A., CANADA, AUSTRALIA
AND EUROPE MODELS ONLY) ..................83
Zone 2 connections.................................................. 83
Remote controlling Zone 2...................................... 84
EDITING SOUND FIELD PARAMETERS ......86
What is a sound field ............................................... 86
Changing parameter settings ................................... 86
SOUND FIELD PARAMETER
DESCRIPTIONS...............................................88
TROUBLESHOOTING .......................................93
RESETTING THE FACTORY PRESETS ........98
GLOSSARY...........................................................99
Audio formats.......................................................... 99
Sound field programs............................................. 100
Audio information ................................................. 100
Video signal information....................................... 101
SPECIFICATIONS.............................................102
CONTENTS
INTRODUCTION
PREPARATION
BASIC OPERATION
SOUND FIELD PROGRAMS
ADVANCED OPERATION
ADDITIONAL INFORMATION
FEATURES
2
Built-in 7-channel power amplifier
Minimum RMS output power
(0.06% THD, 20 Hz to 20 kHz, 8 )
Front: 100 W + 100 W
Center: 100 W
Surround: 100 W + 100 W
Surround back: 100 W + 100 W
Sound field features
Proprietary YAMAHA technology for the creation of
sound fields
Dolby Digital/Dolby Digital EX decoder
DTS/DTS-ES Matrix 6.1, Discrete 6.1, DTS Neo:6,
DTS 96/24 decoder
Dolby Pro Logic/Dolby Pro Logic II/
Dolby Pro Logic IIx decoder
Virtual CINEMA DSP
SILENT CINEMA
Sophisticated AM/FM tuner
40-station random and direct preset tuning
Automatic preset tuning
Preset station shifting capability (preset editing)
XM Satellite Radio
XM Satellite Radio programming (using the “XM
connect and Play digital antenna accessory”, sold
separately)
Other features
YPAO: YAMAHA Parametric Room Acoustic
Optimizer for automatic speaker setup
192-kHz/24-bit D/A converter
A SET MENU that provides you with items for
optimizing this unit for your audio/video system
8 additional input jacks for discrete multi-channel input
PURE DIRECT for pure fidelity sound with analog and
PCM sources
On-screen display function helpful in controlling this
unit
S-video signal input/output capability
Component video input/output capability
Video signal conversion (Composite video S-video
Component video) capability for monitor out
Optical and coaxial digital audio signal jacks
Sleep timer
Cinema and music night listening modes
Remote control with preset remote control codes and
“learning” capability
Zone 2 custom installation facility (U.S.A., Canada,
Australia and Europe models only)
y indicates a tip for your operation.
Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button
names differ between the main unit and the remote control, the button name on the remote control is given in parentheses.
This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In
case of differences between the manual and product, the product has priority.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, “Surround EX”, and the double-D symbol
are trademarks of Dolby Laboratories.
“SILENT CINEMA” is a trademark of YAMAHA
CORPORATION.
“DTS”, “DTS-ES”, “Neo:6” and “DTS 96/24” are trademarks of
Digital Theater Systems, Inc.
The XM name and related logos are registered trademarks of XM
Satellite Radio Inc.
FEATURES
GETTING STARTED
3
INTRODUCTION
Please check that you received all of the following parts.
1 Press the part and slide the battery
compartment cover off.
2
Insert four supplied batteries (AAA, R03,
UM-4) according to the polarity markings
(+ / –) on the inside of the battery
compartment.
3 Slide the cover back until it snaps into place.
Notes on batteries
Change all of the batteries if you notice the following
conditions; the operation range of the remote control decreases,
the indicator does not flash or its light becomes dim.
Do not use old batteries together with new ones.
Do not use different types of batteries (such as alkaline and
manganese batteries) together. Read the packaging carefully as
these different types of batteries may have the same shape and
color.
If the batteries have leaked, dispose of them immediately. Avoid
touching the leaked material or letting it come into contact with
clothing, etc. Clean the battery compartment thoroughly before
installing new batteries.
Do not throw away batteries with general house waste; dispose
of them correctly in accordance with your local regulations.
GETTING STARTED
Supplied accessories
TRANSMIT
RE-NAME
INPUT MODE
STANDBY
SYSTEM
POWER
AB
PHONO
CDMD/CD-RTUNERV-AU X
DVD
AMP
POWERPOWER
REC
AUDI O
MUTE
MENUTITLE
CH CH
VOL
DISC SKIP
SET MENU
LEVEL
PRESET/CH
SRCH MODE
A-E/CAT.
BAND
TV INPUT
TV VOL
ON SCREEN
STRAIGHT
MOVIEENTERTAINMUSICSTEREO
4321
8
10
7
09
65
ENT.
PURE DIRECT
EXTD SUR.STANDARD SELECT
NIGHT
SPEAKERSAB
EFFECTMEMORY
CHP/INDEX
DISPLAYRETURN
TV MUTE
ENTER
TV VOL
AVTV
SELECT
VCR 1DTV/CBL DVR/VCR2
MULTI CH IN
SLEEP
CLEAR LEARN
Remote control
Batteries (4)
(AAA, R03, UM-4)
Indoor FM antenna
(U.S.A., Canada, China
and General models)
AM loop antenna
Indoor FM antenna
(Europe, Australia and
Korea models)
Optimizer microphone
Installing batteries in the remote
control
1
3
2
If the remote control is without batteries for more than
2 minutes, or if exhausted batteries remain in the
remote control, the contents of the memory may be
cleared. When the memory is cleared, insert new
batteries, set up the remote control code and program
any acquired functions that may have been cleared.
CONTROLS AND FUNCTIONS
4
1 STANDBY/ON
Turns on this unit or sets it to the standby mode. When
you turn on this unit, you will hear a click and there will
be a 4 to 5-second delay before this unit can reproduce
sound.
In standby mode, this unit consumes a small amount of power in
order to receive infrared-signals from the remote control.
2 OPTIMIZER MIC jack
Use to connect and input audio signals from the supplied
microphone for use with the AUTO SETUP function (see
page 24).
3 Remote control sensor
Receives signals from the remote control.
4 Front panel display
Shows information about the operational status of this
unit.
5 A/B/C/D/E, NEXT, CATEGORY
*
Selects one of the 5 preset station groups (A to E) when
the unit is in tuner mode.
Selects the speaker channel to be adjusted when the unit is
not in tuner mode.
6 PRESET/TUNING/ CH* l / h, LEVEL –/+
Selects preset station number 1 to 8 when the colon (:) is
displayed next to the band indication in the front panel
display when the unit is in tuner mode. Selects the tuning
frequency when the colon (:) is not displayed.
Adjusts the level of the speaker channel selected using
A/B/C/D/E (NEXT) when the unit is not in tuner mode.
7 MEMORY (MAN’L/AUTO FM)
Stores a station in the memory. Hold down this button for
more than 3 seconds to start automatic preset tuning.
8 TUNING MODE (AUTO/MAN’L MONO),
DISPLAY*
Switches the tuning mode between automatic (AUTO
indicator on) and manual (AUTO indicator off).
9 VIDEO AUX jacks
Input audio and video signals from a portable external
source such as a game console. To reproduce source
signals from these jacks, select V-AUX as the input
source.
0 VOLUME
Controls the output level of all audio channels.
This does not affect the REC OUT level.
CONTROLS AND FUNCTIONS
Front panel
MAIN
ZONE ON/OFF
ZONE 2
DISPLAY
S VIDEO VIDEO OPTICALL AUDIO R
LEVEL
CATEGORY
NEXT
SEARCH MODE
EFFECT
MEMORY
MAN'L/AUTO FM
FM/AM
XM
PRESET/TUNING
EDIT
OPTIMIZER MIC A/B/C/D/E
PROGRAM
l PRESET/TUNING/CH h
TUNING MODE
AUTO/MAN'L MONO
PURE DIRECTINPUT MODETONE CONTROLSTRAIGHT
SPEAKERSPHONES
SILENT CINEMA
STANDBY
/ON
BA
MULTI CH
INPUT
VOLUME
VIDEO AUX
INPUT
31452609
J
KHGEBACDF I
L
78
(U.S.A. model)
(U.S.A., Canada,
Australia and Europe
models only)
Note
CONTROLS AND FUNCTIONS
5
INTRODUCTION
A PHONES (SILENT CINEMA) jack
Outputs audio signals for private listening with
headphones. When you connect headphones, no signals
are output to the PRE OUT jacks or to the speakers.
All Dolby Digital and DTS audio signals are mixed down
to the left and right headphone channels.
B SPEAKERS A/B
Turns on or off the set of front speakers connected to the A
and/or B terminals on the rear panel each time the
corresponding button is pressed.
C PRESET/TUNING (EDIT), SEARCH MODE
*
Switches the function of PRESET/TUNING/CH l / h
(LEVEL) between selecting preset station numbers and
tuning.
D STRAIGHT (EFFECT)
Switches the sound fields off or on. When STRAIGHT is
selected, input signals (2-channel or multi-channel) are
output directly from their respective speakers without
effect processing.
E FM/AM, XM
*
Switches the reception band when the unit is in tuner
mode.
F PROGRAM
Use to select sound field programs or adjust the bass/treble
balance (in conjunction with TONE CONTROL).
G TONE CONTROL
Use to adjust the bass/treble balance for the front left and
right, center, presence and subwoofer channels (see
page 31).
H INPUT MODE
Sets the priority (AUTO, DTS, ANALOG) for the type of
signals received when one component is connected to two
or more of this unit’s input jacks (see page 37).
I INPUT selector
Selects the input source you want to listen to or watch.
J MULTI CH INPUT
Selects the source connected to the MULTI CH INPUT
jacks. When selected, the MULTI CH INPUT source takes
priority over the source selected with INPUT (or the input
selector buttons on the remote control).
K PURE DIRECT
Turns on or off PURE DIRECT mode (see page 35).
U.S.A., Canada, Australia and Europe
models only
L ZONE ON/OFF buttons
MAIN
Switches this unit’s operation to control the component in
the main room (see page 84).
ZONE 2
Switches this unit’s operation to control the component in
the second room (Zone 2) (see page 84).
*
Available only when the unit is in the XM Satellite Radio
mode (see page 45).
CONTROLS AND FUNCTIONS
6
This section describes the function of each control on the
remote control used to control this unit. To operate other
components, see “REMOTE CONTROL FEATURES” on
page 75.
1 Infrared window
Outputs infrared control signals. Aim this window at the
component you want to operate.
2 TRANSMIT indicator
Flashes while the remote control is sending signals.
3 STANDBY
Sets this unit in the standby mode.
4 SYSTEM POWER
Turns on the power of this unit.
5 Input selector buttons
Select the input source and change the control area.
6 Display window
Shows the name of the selected source component that
you can control.
7 LEVEL, BAND
Selects the speaker channel to be adjusted and sets the
level.
Switches the reception band when the unit is in tuner
mode.
8 Cursor buttons u / d / j / i /ENTER
Use to select and adjust sound field program parameters or
SET MENU items.
Press j / i to select a preset station group (A to E) when
the unit is in tuner mode.
Press u / d to select a preset station number (1 to 8)
when the unit is in tuner mode.
9 RETURN, MEMORY*
Returns to the previous menu level when adjusting the
SET MENU parameters.
0 Sound field program/numeric buttons
Use to select sound field programs.
Use numbers 1 through 8 to select preset stations when the
unit is in tuner mode.
Use SELECT to playback 2-channel sources in multiple
channel format (see page 34).
Use EXTD SUR. to switch between 5.1 or 6.1/7.1-channel
playback of multi-channel software (see page 33).
Use PURE DIRECT to turn on or off PURE DIRECT
mode (see page 35).
A SPEAKERS A/B
Use to turn on or off the set of front speakers connected to
the A and/or B terminal on the rear panel each time the
corresponding button is pressed.
B RE-NAME
Use to change the input source name in the display
window (see page 80).
Remote control
TRANSMIT
RE-NAME
INPUT MODE
STANDBY
SYSTEM
POWER
AB
PHONO
CDMD/CD-RTUNERV-AUX
DVD
AMP
POWERPOWER
REC
AUDIO
MUTE
MENUTITLE
CH CH
VOL
DISC SKIP
SET MENU
LEVEL
PRESET/CH
SRCH MODE
A-E/CAT.
BAND
TV INPUT
TV VOL
ON SCREEN
STRAIGHT
MOVIEENTERTAINMUSICSTEREO
4321
8
10
7
09
65
ENT.
PURE DIRECT
EXTD SUR.STANDARD SELECT
NIGHT
SPEAKERSAB
EFFECTMEMORY
CHP/INDEX
DISPLAYRETURN
TV MUTE
ENTER
TV VOL
AVTV
SELECT
VCR 1DTV/CBL DVR/VCR2
MULTI CH IN
SLEEP
CLEAR LEARN
B
C
D
E
F
H
J
K
L
M
N
O
I
8
9
7
0
2
3
4
1
6
5
G
A
CONTROLS AND FUNCTIONS
7
INTRODUCTION
C CLEAR
Use to clear functions acquired when using the learn and
rename features, or setting remote control codes (see
page 81).
D LEARN
Use to set up manufacturer codes or program functions
from other remote controls (see pages 76 and 79).
E SLEEP
Sets the sleep timer.
F INPUT MODE
Sets the priority (AUTO, DTS, ANALOG) for the type of
signals received when one component is connected to two
or more of this unit’s input jacks (see page 37).
G MULTI CH IN
Selects MULTI CH INPUT when using an external
decoder (etc.).
H SELECT k/n
Selects another component that you can control
independently of the input component selected with the
input selector buttons.
I AMP
Selects the AMP mode. You must select the AMP mode to
control the main unit.
J VOL +/
Increases or decreases the volume level.
K MUTE
Mutes the sound. Press again to restore the audio output to
the previous volume level.
L SET MENU, SRCH MODE
*
Activates the SET MENU function.
M ON SCREEN
Selects the display mode of the on-screen display (OSD)
this unit sends to your video monitor.
N STRAIGHT (EFFECT)
Switches the sound fields off or on. When STRAIGHT is
selected, input signals (2-channel or multi-channel) are
output directly from their respective speakers without
effect processing.
O NIGHT, ENT.
*
Turns on or off the night listening modes (see page 35).
*
Available only when the unit is in the XM Satellite Radio
mode (see page 45).
The remote control transmits a directional infrared beam.
Be sure to aim the remote control directly at the remote
control sensor on the main unit during operation.
Handling the remote control
Do not spill water or other liquids on the remote
control.
Do not drop the remote control.
Do not leave or store the remote control in the
following types of conditions:
places of high humidity, such as near a bath
places of high temperature, such as near a heater or
stove
extremely low temperatures
dusty places
Using the remote control
DISPLAY
S VIDEO VIDEO OPTICALL AUDIO R
LEVEL
CATEGORY
NEXT
SEARCH MODE
EFFECT
MEMORY
MAN'L/AUTO FM
FM/AM
XIM
PRESET/TUNING
EDIT
OPTIMIZER MIC A/B/C/D/E
PROGRAM
l PRESET/TUNING/CH h
TUNING MODE
AUTO/MAN'L MONO
PURE DIRECTINPUT MODETONE CONTROLSTRAIGHT
SPEAKERSPHONES
SILENT CINEMA
STANDBY
/ON
BA
MULTI CH
INPUT
VOLUME
VIDEO AUX
INPUT
30 30
TRANSMIT
RE–NAME
CLEAR
LEARN
POWER SLEEP
STANDBY
INPUT MODE
SYSTEM
PHONO TUNER CD
MULTI CH IN
V
-
AUX
CBL/SAT MD/TAPE CD-R
DTV DVR/VCR2VCR 1 DVD
SELECT
POWER
TV
POWER
AV
AMP
REC
DISC SKIP
AUDIO
VOL
LEVEL
TITLE
BAND
TV INPUT
SRCH MODE
TV VOL
PRESET/CH
SET MENU
MENU
A-E/CAT.
MUTE
CH
TV MUTE
ENTER
CH
PRESET PRESET
RETURN
TV VOL
ON SCREEN
DISPLAY
STRAIGHT
EFFECTMEMORY
STEREO
MUSIC
ENTERTAIN MOVIE
12
34
56
8
STANDARD
SELECT
EXTD SUR.
PURE DIRECT
7
90
ENT.
+10
NIGHT
A
SPEAKERS
B
CHP/INDEX
Approximately 6 m (20 ft)
CONTROLS AND FUNCTIONS
8
1 Decoder indicators
When any of this unit’s decoders function, the respective
indicator lights up.
2 VIRTUAL indicator
Lights up when Virtual CINEMA DSP is active (see
page 36).
3 SILENT CINEMA indicator
Lights up when headphones are connected and a sound
field program is selected (see page 31).
4 Input source indicators
A cursor lights to show the current input source.
5 Sound field indicators
Light to indicate the active DSP sound fields.
6 CINEMA DSP indicator
Lights up when you select a CINEMA DSP sound field
program.
7 YPAO indicator
Lights up during the auto setup procedure and when the
auto setup speaker settings are used without any
modifications.
8 AUTO indicator
Lights up when this unit is in automatic tuning mode.
9 TUNED indicator
Lights up when this unit is tuned into a station.
0 STEREO indicator
Lights up when this unit is receiving a strong signal for an
FM stereo broadcast while the AUTO indicator is lit.
A MEMORY indicator
Flashes to show that a station can be stored.
B MUTE indicator
Flashes while the MUTE function is on.
C VOLUME level indication
Indicates the current volume level.
D PCM indicator
Lights up when this unit is reproducing PCM (Pulse Code
Modulation) digital audio signals.
E STANDARD
Lights up when a decoder is selected (see page 34).
F NIGHT indicator
Lights up when you select night listening mode.
G SP A B indicators
Light up according to the set of front speakers selected.
Both indicators light up when both sets of speakers are
selected.
H Headphones indicator
Lights up when headphones are connected.
I HiFi DSP indicator
Lights up when you select a HiFi DSP sound field
program.
J Multi-information display
Shows the current sound field program name and other
information when adjusting or changing settings.
Front panel display
PHONOCDTUNER
MD/CD-R
DVD
DTV/CBL
V-AUX
VCR1
DVR/VCR2
96
24
q
PL
q
EX
q
PL
MATRIX DISCRETE
SILENT CINEMA
NIGHT
ZONE2STANDARD
HD AUTO
YPAO
PS
PS
HOLD
HOLD
RT CT
RT CT
EON
EON
PTY
PTY
PTY
PTY
TUNED STEREO MUTE
VOLUME
MEMORY
SLEEP
VIRTUAL
PCM
q
PL x
A B
SP
mS
dB
ft
dB
96/24
HiFi DSP
LFE
LCR
SL SB SR
q
DIGITAL
t
123456789 A B C0
O
IJ M
KNLED
FH
G
(U.S.A., Canada, Australia,
U.K. and Europe models
only)
Presence DSP sound field
Listening position
Left surround
DSP sound field
Right surround
DSP sound field
Surround back DSP sound field
CONTROLS AND FUNCTIONS
9
INTRODUCTION
K SLEEP indicator
Lights up while the sleep timer is on.
L 96/24 indicator
Lights up when a DTS 96/24 signal is input to this unit.
M LFE indicator
Lights up when the input signal contains the LFE signal.
N Input channel indicators
Indicate the channel components of the current digital
input signal.
U.S.A., Canada, Australia and Europe
model only
O ZONE 2 indicator
Lights up when Zone 2 power is on.
CONTROLS AND FUNCTIONS
10
1 DIGITAL OUTPUT jacks
See page 19 for details.
2 Audio component jacks
See page 19 for connection information.
3 Video component jacks
See pages 16 and 18 for connection information.
4 Antenna terminals
(except U.K. model)
See page 21 for connection information.
5 PRESENCE/ZONE 2 speaker terminals
(U.S.A., Canada, Australia and Europe
models)
PRESENCE speaker terminals
(other models)
See page 13 for connection information.
6 REMOTE IN/OUT jacks
(U.S.A., Canada, Australia and Europe models
only)
See page 83 for details.
7 XM jack
See page 45 for connection information.
8 CONTROL OUT jack
(U.S.A., Canada, Australia, U.K. and Europe
models only)
This is a control expansion terminal for commercial use.
9 AC OUTLET(S)
Use to supply power to your other A/V components (see
page 22).
0 DIGITAL INPUT jacks
See pages 16, 18 and 19 for details.
A MULTI CH INPUT jacks
See page 17 for connection information.
B ZONE 2 OUTPUT jacks
(U.S.A., Canada, Australia and Europe models
only)
These jacks output analog signals only. See page 83 for
details.
TUNER INPUT jacks
(U.K. model only)
C PRE OUT jacks
See page 20 for connection information.
D Speaker terminals
See page 13 for connection information.
General models only
VOLTAGE SELECTOR
See page 22 for details.
Rear panel
GND
AUDIO AUDIO
DIGITAL
INPUT
DVD
DVD
CD
COAXIAL
DTV/CBL
MD/CD-R
MD/CD-R
SUB
WOOFER
SURROUND
BACK
SURROUND
FRONT
OUT
(REC)
IN
(PLAY)
MD
/CD-R
CD
PHONO
DVD
VIDEO
MONITOR
OUT
DTV
/CBL
DVD
COMPONENT VIDEO
PR PB Y
75 UNBAL.
FM
ANT
AM
ANTGND
TUNER
DTV/
CBL
IN
VCR 1
OUT
IN
DVR/
VCR 2
OUT
CENTER
DIGITAL
OUTPUT
MULTI CH INPUT
ZONE 2
OUTPUT
VIDEO S VIDEO
MONITOR OUT
FRONT
SUB
WOOFER
FRONT
A
B
CENTER SINGLE
PRE OUT
SURROUND
SURROUND
BACK
PRESENCE/
ZONE 2
OUT
IN
REMOTE
CONTROL
OUT
AC OUTLETS
SWITCHED
+12V
15mA MAX.
SPEAKERS
SURROUND
CENTER SURROUND BACK
OPTICAL
12 3 48965
0A B C D
XM
7
(U.S.A. model)
SPEAKER SETUP
11
PREPARATION
The speaker layout below shows the standard ITU-R
*
speaker setting. You can use it to enjoy CINEMA DSP
and multi-channel audio sources.
*
ITU-R is the radio communication sector of the ITU
(International Telecommunication Union).
Front speakers (FR and FL)
The front speakers are used for the main source sound plus
effect sounds. Place these speakers an equal distance from
the ideal listening position. The distance of each speaker
from each side of the video monitor should be the same.
Center speaker (C)
The center speaker is for the center channel sounds
(dialog, vocals, etc.). If for some reason it is not practical
to use a center speaker, you can do without it. Best results,
however, are obtained with the full system. Align the front
face of the center speaker with the front face of your video
monitor. Place the speaker centrally between the front
speakers and as close to the monitor as possible, such as
directly over or under it.
Surround speakers (SR and SL)
The surround speakers are used for effect and surround
sounds. Place these speakers behind your listening
position, facing slightly inwards, about 1.8 m (6 ft) above
the floor.
Surround back speakers (SBR and SBL)
The surround back speakers supplement the surround
speakers and provide for more realistic front-to-back
transitions. Place these speakers directly behind the
listening position and at the same height as the surround
speakers. They should be positioned at least 30 cm (12 in)
apart. Ideally, they should be positioned at the same width
as the front speakers.
Subwoofer
The use of a subwoofer, such as the YAMAHA Active
Servo Processing Subwoofer System, is effective not only
for reinforcing bass frequencies from any or all channels,
but also for high fidelity reproduction of the LFE (low-
frequency effect) channel included in Dolby Digital and
DTS software. The position of the subwoofer is not so
critical, because low bass sounds are not highly
directional. But it is better to place the subwoofer near the
front speakers. Turn it slightly toward the center of the
room to reduce wall reflections.
Presence speakers (PR and PL)
Presence speakers supplement the sound from the front
speakers with extra ambient effects produced by CINEMA
DSP (see page 56). These effects include sounds that
filmmakers intend to locate a little farther back behind the
screen in order to create more theater-like ambience. Place
these speakers at the front of the room about 0.5 - 1 m
(1 - 3 ft) outside the front speakers, facing slightly
inwards, and about 1.8 m (6 ft) above the floor.
SPEAKER SETUP
Speaker placement
60˚
30˚
PL
PR
SBR
SBL
FL
FR
C
SL
SR
SR
80˚
SL
30 cm (12 in) or more
1.8 m (6 ft)
1.8 m (6 ft)
12
SPEAKER SETUP
Be sure to connect the left channel (L), right channel (R),
“+” (red) and “–” (black) properly. If the connections are
faulty, no sound will be heard from the speakers, and if the
polarity of the speaker connections is incorrect, the sound
will be unnatural and lack bass.
If you will use 4 or 6 ohm speakers, be sure to
set this unit’s speaker impedance setting to 4
ohms before using (see page 23).
Before connecting the speakers, make sure that the
power of this unit is off.
Do not let the bare speaker wires touch each other or do
not let them touch any metal part of this unit. This
could damage this unit and/or speakers.
Use magnetically shielded speakers. If this type of
speakers still creates the interference with the monitor,
place the speakers away from the monitor.
A speaker cord is actually a pair of insulated cables
running side by side. One cable is colored or shaped
differently, perhaps with a stripe, groove or ridges.
Connect the striped (grooved, etc.) cable to the “+” (red)
terminals on this unit and your speaker. Connect the plain
cable to the “–” (black) terminals.
1 Remove approximately 10 mm (3/8") of
insulation from the end of each speaker
cable.
2 Twist the exposed wires of the cable together
to prevent short circuits.
3 Unscrew the knob.
4 Insert one bare wire into the hole in the side
of each terminal.
5 Tighten the knob to secure the wire.
Connecting to PRESENCE/ZONE 2 or
PRESENCE speaker terminals
1 Open the tab.
2 Insert one bare wire into the hole of each
terminal.
3 Return the tab to secure the wire.
Banana plug connections
(With the exception of U.K. and Europe models)
First, tighten the knob and then insert the banana plug
connector into the end of the corresponding terminal.
y
You can also use banana plugs with the PRESENCE/ZONE 2 and
PRESENCE speaker terminals. Open the tab, then insert one
banana plug connector into the hole of each terminal. Do not
attempt to close the tabs after connecting the banana plugs.
Speaker connections
CAUTION
10 mm (3/8")
1
2
Red: positive (+)
Black: negative (–)
3
4
5
2
1
3
Banana plug
(With the exception of U.K. and
Europe models)
13
SPEAKER SETUP
PREPARATION
FRONT
SUB
WOOFER
FRONT
A
B
CENTER SINGLE
PRE OUT
SURROUND
SURROUND
BACK
PRESENCE/
ZONE 2
SPEAKERS
SURROUND
CENTER SURROUND BACK
231
6 7 10
98
45
Subwoofer
system
Center
speaker
Front speakers (A)
Surround back
speakers
LeftRight
LeftRight
Surround speakers
Front
speakers
(B)
(U.S.A. model)
LeftRight
LeftRight
Presence speakers
You can connect both surround back and presence speakers to this unit, but they do not output sound simultaneously.
The surround back speakers output the surround back channel included in Dolby Digital EX and DTS-ES software and only
operate when the Dolby Digital EX, DTS-ES or Dolby Pro Logic IIx decoder is turned on.
The presence speakers output ambient effects created by the DSP sound fields. They do not output sound when other sound fields
are selected.
14
SPEAKER SETUP
FRONT terminals
Connect one or two speaker systems (6, 7) to these
terminals. If you use only one speaker system, connect it
to the FRONT A or B terminals.
CENTER terminals
Connect a center speaker (8) to these terminals.
SURROUND terminals
Connect surround speakers (4, 5) to these terminals.
SUBWOOFER jack
Connect a subwoofer with built-in amplifier (1), such as
the YAMAHA Active Servo Processing Subwoofer
System, to this jack.
SURROUND BACK terminals
Connect surround back speakers (9, 10) to these terminals.
If you only connect one surround back speaker, connect it
to the left (L) terminals.
PRESENCE terminals
Connect presence speakers (2, 3) to these terminals.
*
If you are using either the U.S.A., Canada, Australia, U.K. or
Europe model, you can also use these speakers as Zone 2
speakers (see page 72).
1
6
7
8
9
2
3
5
4
10
Speaker layout
CONNECTIONS
15
PREPARATION
Do not connect this unit or other components to the mains
power until all connections between components are
complete.
Cable indications
Analog jacks
You can input analog signals from audio components by
connecting audio pin cable to the analog jacks on this unit.
Connect red plugs to the right jacks and white plugs to the
left jacks.
Digital jacks
This unit has digital jacks for direct transmission of digital
signals through either coaxial or fiber optic cables. You
can use the digital jacks to input PCM, Dolby Digital and
DTS bitstreams. When you connect components to both
the COAXIAL and OPTICAL jacks, priority is given to
the input signals from the COAXIAL jack. All digital
input jacks are compatible with 96-kHz sampling digital
signals.
This unit handles digital and analog signals independently. Thus
audio signals input to the analog jacks are only output to the
analog OUT (REC) jacks. Likewise audio signals input to the
digital (OPTICAL or COAXIAL) jacks are only output to the
DIGITAL OUTPUT jack.
Dust protection cap
Pull out the cap from the optical jack before you connect
the fiber optic cable. Do not discard the cap. When you are
not using the optical jack, be sure to put the cap back in
place. This cap protects the jack from dust.
Video jacks
This unit has three types of video jacks. Connection
depends on the availability of input jacks on your monitor.
The signals input through the S VIDEO jacks on this unit
are automatically converted for output through the
VIDEO jacks. When VIDEO CONV. is set to ON (see
page 71), signals input through the VIDEO jacks can be
output through the S VIDEO and COMPONENT VIDEO
jacks. Likewise, signals input through the S VIDEO jacks
can also be output through the COMPONENT VIDEO
jacks.
VIDEO jacks
For conventional composite video signals.
S VIDEO jacks
For S-Video signals, separated into luminance (Y) and
color (C) video signals to achieve high-quality color
reproduction.
COMPONENT VIDEO jacks
For component signals, separated into luminance (Y) and
color difference (P
B, PR) to provide the best quality in
picture reproduction.
When signals are input through both the S VIDEO and VIDEO
jacks, signals input through the S VIDEO jack have priority.
CONNECTIONS
Before connecting components
Note
CAUTION
S
V
O
V
V
V
L
R
C
Y
P
B
PR
left analog cables
right analog cables
optical cables
coaxial cables
video cables
S-video cables
For analog signals
For digital signals
For video signals
component video cables
Note
VIDEO
S VIDEO
COMPONENT VIDEO
P
R
P
B
Y
S VIDEO
VIDEO
COMPONENT
VIDEO
Signal flow inside this unit
Only when VIDEO CONV. is set to ON
(see page 71).
Output
(MONITOR OUT)
Input
16
CONNECTIONS
Connections for DVD playback
Be sure to connect your video source components in the same way you connect your video monitor to this unit if VIDEO CONV. (see
page 71) is set to OFF. For example, if you connect your video monitor to this unit using a VIDEO connection, connect your video
source components to this unit using the VIDEO connections. (Even when V CONV. is set to OFF, S-video signals input from your
video source component are automatically converted to composite signals in this unit.)
Connecting video components
Note
VIDEO
AUDIO
DIGITAL
INPUT
DVD
DVD
COAXIAL
DVD
MONITOR
OUT
DVD
COMPONENT VIDEO
PR PB Y
VIDEO S VIDEO
MONITOR OUT
S
P
R PB Y
V
LRC
O
DVD player
Video
monitor
(U.S.A. model)
Optical out
Video out
Audio out
Video in
Coaxial out
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107

Yamaha RX-V757 Manuale utente

Categoria
Ricevitori AV
Tipo
Manuale utente