In the event of missing or defective parts please call our customer service dept. at
1 800 282 9346
(Mon. to Fri. 8:00 AM to 5:00 PM ES.T)
1. Rafters (5)
1 1/2” x 4 1/2” x 38" - 10838
2. Pergola End Caps (14)
- 10700-1
3. Post Caps (4)
- 10824
4. Right Posts (2)
4” x4” x 84" - 10792
5. Left Posts (2)
4” x4” x 84" - 10821
6. Post Trims (4)
- 10737-1
7. Carrying Beams (2)
1 1/2” x 4 1/2” x 63 1/2" - 10834-1
8.
Side Panel Top-Rails
(2)
1 1/2” x 1 1/2” x 31 5/8“ - 10822
9. Side Panel Vertical Spindles (10)
7/8” x 1 1/2” x 10 3/8” - 10795
10. Side Panel Middle Rails (2)
1 1/2” x 1 1/2” x 31 5/8“ - 10823
11. Side Panel Square Lattices (2)
1/2” x 26 1/2” x 47 3/4” - 10793
12. Side Panel Horizontal Bottom Rails (2)
1 1/2” x 1 1/2” x 31 5/8" - 10794
13.
3 in. (7.6 cm.)
Stainless Steel Screws
(for Rafters) (26)
- 20007
14.
Tube of Vinyl Glue
- 20000
Tools You Will Need
• Hammer
• Tape Measure
• Level
• Stool or Short Ladder
• Shovel or Auger
• Cordless Drill
General Information
•
Read Instructions through carefully before beginning assembly.
• When assembling components, place on a non-abrasive surface
(i.e. shipping box) to avoid scratching.
• We recommend an area approx 10’x 8’ for unobstructed assembling.
• You should not need to use excessive force when assembling components.
ASSEMBLY INSTRUCTIONS
11
10
9
1
8
2
(Not to scale)
4
Please read through before starting assembly.
IMPORTANT: CHECK THE INSIDE OF YOUR POSTS FOR ALL MATERIALS.
Check Box for These Contents
13
12
1
7
V2.5/111220
80.5 in
50 in
86.5 in
58 in
77.75 in
10.25 in
24 in
32 in
58.5 in 82 in
52.25 in
6
3
5
www.wearevita.com
STEP ON E
2
Lay out the two carrying beams as illustrated with pre-
drilled holes facing up.
Position the five rafters over the respective pre
drilled holes
on the carrying beams as illustrated.
Using the 3” screws fasten the five rafters to the
carrying
beams.
Apply vinyl glue to the inside of the end cap and install
pergola end caps as illustrated.
Assemble the Arbor Top
1
2
3
STEP T WO
Assemble the Side Panels
1
2
3
4
2
1
1234
4
4
Insert the lattice into the bottom rail as shown.
Note: Bottom rail will have 7 holes on one side only
Insert the lattice assembly into the middle rail.
Note: Middle rail will have 7 holes on the bottom side and 5
holes on the top
Insert the five spindles into the top side of the middle rail.
Note: The middle rail will have 5 holes on one side only,
share the space within the middle rail for lattice and
spindles.
Slide the top rail over the lattice assembly.
Repeat for other side panel.
3
Note: The self-auguring screws will drill through the internal rib.
Keep the screw straight to drill through the internal rib.
STEP T WO
3
STEP THREE
Set out one post and complete the side panel by inserting
the side panel assembly into the holes on the post. Push rails
until the tabs snap into place.
Repeat for the adjacent post.
Note that there is a Left and Right post. They are marked at
the top of the post.
Each side panel should have a Left and Right post.
Attach Side Panels to Posts
1
2
4
3
STEP T WO
ST EP FO UR
Slide trim caps into place as illustrated.
If you purchased the Trim Kit, also slide the second set of trim
caps and base moldings at this point.
Glue and insert post caps on top of posts as illustrated
Attach Trim Caps to Posts
1
2
3
4
5
5
“R”
on underside of post top.
“L”
on underside of post top.
ST EP FIVE
Move side panels to their final location and adjust the opening
width to 50 in. (127 cm.).
Place the pre-assembled arbor top onto the post as illustrated.
Fasten the main carrying beams onto the posts using two screws
per side as illustrated
.
Fasten the rafters to the posts using two screws per side as
illustrated.
Connect the Pergola Top to the Posts
1
2
4
2
50 in.
127 cm.
1
3
3
3
Note: To glue the post trims in place:
1. Slide the post trim down.
2. Apply a generous amount of
vinyl glue around the post.
3. Slide the post trim back up to
desired location and allow a few
minutes to cure.
Level
Move the arbor to its final location (you will need a he lper).
When you have identified the location of each post, mark the
positions of the ground and then move the arbor aside.
Excavate four holes approx 33 in. (83.8 cm.) deep. The location and
e
xcavation of these four holes is the most critical step and should
be completed with care. The depth of these holes will allow the
post extension (if ch osen as option) joint to be hidden 3 in. (7.6 cm.)
under the ground.
Carefully move the arbor back into position and level both
horizontal and vertically.
Backll the holes with either gravel or cement
.
1
2
3
4
5
Arbor s must be well secured to prevent tipping over from
wind load, etc.
Into Earth wit h Concrete Footin g
(Option One)
(Assumi ng posts h ave been extended)
Shown with
Optional 4 x 4
Post Extensions
1
(Posts have been extended with 4x4 Professional Post Extension Kit)
4
3
2
(Measuremen ts sh own are inside to inside of posts)
33 in.
83.8 cm.
10 in.
25.4 cm.
50 in.
127 cm.
20 in.
51 cm.
5
STEP FIV E
Inst all th e Sid e Pa nel s
You have Three Options to Complete this Step.
(All purch ased se parately)
OP TI ON ON E - If Your Arbor:
•is going to be installed with fencing or a gate
•is located in a high wind or hurricane area
•is located in ground conditions that are not level
Consider Using:
A - 4x4
Professional Post Extension Kit
(30 in./7 6.2 cm. long), (Kit of 4)
• Purchase from Vita, www.wearevita.com
• Recommended to be installed in concrete footings
• Follow instructions included with the kit
-or -
B - 4 x 4 x 8’ (2 43. 8 cm.) Long Wood Post (4)
• Purchase separate from your local lumberyard
• Recommended to be installed in concrete footing
OP TI ON T WO - If Your Arbor:
•is intended to be used as a stand alone garden accent or pathway
•is located on level ground
Consider Using:
• Purchase from Vita, www.wearevita.com
•Instructions are included with the kit
OP TION THR E E - If Your Arbor:
•is going to be installed onto pre-existing concrete or wood surface
Consider Using:
4 x 4 Sur fa ce Mount Kit
• Purchase from your local hardware store
• Follow instructions included with the kit
www. wearevita .com
4” EZ Mount Post (Package of 4)
North America Toll Free Phone: 1 800 282 9346
-
1
-
2
-
3
-
4
-
5
in altre lingue
Documenti correlati
Altri documenti
-
New England Arbors VA84226 Manuale utente
-
Weatherables YWPG-VICTORIAN Guida d'installazione
-
Ironcraft 833661 Guida d'installazione
-
Ironcraft 836140 Guida d'installazione
-
Suncast A01B02 Guida utente
-
Maytag SOV026TB Manuale utente
-
Hilti MSP-Solarpark Istruzioni per l'uso
-
Intel SR1625UR - Server System - 0 MB RAM Manuale utente
