Tecnosystemi SORRISO LED SCA 15 lt - SORRISO SCA 15 lt under boiler acid condensate water pump Manuale del proprietario

Tipo
Manuale del proprietario
Sorriso cable
LEGENDA
1. Pompa Sorriso.
2. Sportellino ispezione.
3. Serbatoio trasp. ispezionabile e lavabile.
4. Filtro serbatoio.
5. Ingresso acqua di condensa.
6. Attacco scarico condensa per tubo Ø4x6.
7. Cavo alimentazione + allarme.
8. N°2 asole per ssaggio pompa.
9. 3° foro per ssaggio pompa.
10. Pulsante per aggancio/sgancio sportellino.
1
2
3
SORRISO CLIMA-SC11
• Portata: 11 lt/h per climatizzatori no a 10 kw
• Mandata max: 8 mt vert. tra pompa e
uscita dell’acqua
• Tensione: 230V 50Hz - 125V 60Hz
• Contatto allarme: NO / 6A
• Dimensioni tubo: ø 4 x 6 (mm)
• Dimensioni pompa: L 220 x P 70 x H 50 (mm)
• Potenza assorbita: 19 W
• Livello sonoro: max 21 dB(A)
• Grado di protezione: IP20
1. Pompa SORRISO CLIMA-SC11.
2. Split.
3. Ingresso acqua.
4. Attacco scarico acqua.
5. Tubo Ø4x6 scarico acqua.
6. Cavo elettrico alimentazione + allarme.
7. Bacinella raccogli condensa split
SORRISO-SCA 15
• Portata: 15 lt/h
• Mandata max: 10 mt vert. tra pompa e
uscita dell’acqua
• Tensione: 230V 50Hz - 125V 60Hz
• Contatto allarme: NO / 6A
• Dimensioni tubo: ø 4 x 6 (mm)
• Dimensioni pompa: L 220 x P 70 x H 50 (mm)
• Potenza assorbita: 19 W
• Livello sonoro: max 29 dB(A)
• Grado di protezione: IP20
INSTALLAZIONE E MESSA IN SERVIZIO
1. Pompa SORRISO-SCA.
2. Caldaia condensazione.
3. Ingresso acqua.
4. Attacco scarico acqua.
5. Tubo scarico condensa.
6. Cavo elettrico alimentazione + allarme.
7. Sifone caldaia*
1
2
3
6
7
4
5
4
7
*
*
5
6
* ATTENZIONE! Solo condensa acida
della caldaia, NO condensa camino
1
2
3
6
7
4
5
1
2
3
4
7
*
*
5
6
LEGEND
1. Sorriso Pump.
2. Inspection door.
3. Transparent tank that can be inspected and
washed.
4. Tank lter.
5. Condensation water inlet.
6. Condensation drain coupling for a Ø4x6 pipe.
7. Power supply cable + alarm.
8. N°2 slots to secure the pump.
9. 3rd hole to fasten the pump.
10. button to fasten/release the door.
1. CLIMA-SC11 SORRISO pump.
2. Split.
3. Water inlet.
4. Water drain coupling.
5. Ø4x6 water drain pipe.
6. Power supply cable + alarm.
7. Split condensate tray
1. SORRISO-SCA pump.
2. Condensing boiler.
3. Water inlet.
4. Water drain coupling.
5. Condensation drain pipe.
6. Power supply cable + alarm.
7. Boiler siphon*
* WARNING! Only acid condensate from the boiler,
NOT ue condensate
SORRISO CLIMA-SC 11
Capacity: 11 l/h for air-conditioners up to 10 Kw
Max supply: 8 vert. m between pump and water
outlet
Voltage: 230V 50Hz - 125V 60Hz
Alarm contact: NO / 6A
Pipe size: ø 4 x 6 (mm)
Pump size: L 220 x P 70 x H 50 (mm)
Absorbed power: 19 W
Sound level: max 21 dB(A)
Protection rating: IP20
SORRISO-SCA 15
Capacity: 15 l/h
Max supply: 10 vert. m between pump and water
outlet
Voltage: 230V 50Hz - 125V 60Hz
Alarm contact: NO / 6A
Pipe size: ø 4 x 6 (mm)
Pump size: L 220 x P 70 x H 50 (mm)
Absorbed power: 19 W
Sound level: max 29 dB(A)
Protection rating: IP20
Supply (Vertical M)
Capacity (litres/hour)
Connection to the power supply
Important! The Sorriso Clima-SC11 and SCA15 pumps must be installed
by qualied personnel and in compliance with the CEI 64-8 standard.
Moreover, make sure the system has been powered off before conducting
any operation.
Power on the electric circuit of the Sorriso Clima-SC11 and SCA15 pumps by
connecting the Light Blue and Brown wires to the mains supply. Use two wires
with an identical or bigger cross-section connected to a protective device that
interrupts the power supply on the phase and neutral conductors and compliant
with current regulations. The cable does not need to be earthed as the circuit has
a double insulation .
The Sorriso Clima-SC11 and SCA15 pumps have a IP20 protection rating: install
away from water. Do not install in cold-storage rooms.
VERY IMPORTANT!! ALWAYS CONNECT THE ALARM SYSTEM
Electrical alarm connection.
the Sorriso Clima-SC11 and SCA15
pumps have a C-NO 6A 250Vac alarm
contact at the ends of the black wires.
For the electrical connection refer to
the wiring diagram in this instruction
leaet. We recommend using the
alarm contact to interrupt the operation
of the external unit (or internal unit for
multisplit systems).
Fuse: 315mA Rapido
Power supply cable
Sorriso SC11
cable power supply
Sorriso SCA15
the Relay is NOT supplied
WITH LED INDICATOR
Code: 12170100L - 12170101L
*WARNING! THE PRESENCE OF THE
ALARM LED DOES NOT EXCLUDE
CONNECTION OF THE ALARM WIRES
YELLOW: POWERED
GREEN: RUNNING
RED: ALARM *
1
2
4
3
ATTENZIONE!! PER MODELLI SORRISO CLIMA-SC11
E SORRISO-SCA15 UTILIZZARE SOLO TUBO Ø 4mm x 6mm
UTILIZZARE SOLO TUBO Ø4 mm x 6 mm PER LA CONNESSIONE TRA
POMPA E SCARICO DELL’ACQUA. ATTENZIONE!!! ESEGUIRE SEMPRE IL
COLLEGAMENTO DI ALLARME
MANTENERE LA POMPA SORRISO IN PIANO. LA POSIZIONE INCLINATA
DELLA POMPA (SUPERIORE A 10°) IMPEDISCE AL GALLEGGIANTE INTERNO
IN POLISTIROLO, DI SCORRERE LIBERAMENTE LUNGO LA PROPRIA SEDE.
UTILIZZARE I 3 TASSELLI E 3 VITI DI FISSAGGIO PER IL POSIZIONAMENTO
DELLA POMPA. (VEDERE SCHEMA DI FORATURA PER IL FISSAGGIO)
N
ON ESEGUIRE STROZZATURE DEL TUBO MA COMPIERE CURVE CON
RAGGIO DI ALMENO 50 mm.
LA PRESENZA DI STROZZATURE DANNEGGIA
IL LAVORO DELLA POMPA. CONSIDERARE CHE AD OGNI CURVA DEL TUBO,
CORRISPONDE UNA PERDITA DI PREVALENZA DI CIRCA 1 mt.
INSERIRE COMPLETAMENTE IL MANICOTTO DI GOMMA DEL TUBO
PROVENIENTE DALLO SCARICO DELLO SPLIT NEL SERBATOIO
PER MODELLO SCA NON UTILIZZARE LA POMPA PER SMALTIRE LA
CONDENSA PROVENIENTE DALLA CANNA FUMARIA: UTILIZZARE SOLO
PER CONDENSA DELLA CALDAIA
ALL’INIZIO DELLA STAGIONE (PRIMA DI ACCENDERE LO SPLIT O LA
CALDAIA), ESEGUIRE SEMPRE UN INTERVENTO DI MANUTENZIONE
ORDINARIA. APRIRE LO SPORTELLO, ESTRARRE IL SERBATOIO E
SCIACQUARLO CON ACQUA: SCIACQUARE ANCHE IL FILTRO.
AL TERMINE DELLA STAGIONE TOGLIERE L'ALIMENTAZIONE ALLA POMPA.
COD. C20001097
REV. 07 / 28-07-2022
8
2
7
8
5
10
3
4
6
1
9
8
2
7
8
5
10
3
4
6
1
9
Mandata (mt Verticali)
Capacità (Litri/ora)
Supply (Vertical M)
Capacity (litres/hour)
La garanzia ha durata di 2 anni a decorrere dalla data di consegna.
L’azienda fornitrice garantisce la qualità dei materiali impiegati e la corretta realizzazione dei
componenti. La garanzia copre difetti di materiale e di fabbricazione e si intende relativa
alla fornitura dei pezzi in sostituzione di qualsiasi componente che presenti difetti, senza che
possa venir reclamata alcuna indennità, interesse o richiesta di danni.
La garanzia non copre la sostituzione dei componenti che risultano danneggiati per:
trasporto non idoneo; installazione non conforme a quanto specicato in questo manuale di
installazione uso e manutenzione; la non osservanza delle speciche tecniche di prodotto;
quant’altro non riconducibile a vizi originari del materiale o di produzione a condizione che il
reclamo del cliente sia coperto dalla garanzia e noticato nei termini e modalità richiesta dal
fornitore, lo stesso si impegnerà, a sua discrezione, a sostituire o riparare ciascun prodotto
o le parti di questo che presentino vizi o difetti.
Collegamento elettrico di alimentazione
Importante! L’installazione della pompa Sorriso Clima-SC11 e SCA15
dev’essere eseguita da personale qualicato e in accordo con la norma
CEI 64-8. Assicurarsi, inoltre, che l’impianto sia fuori tensione prima di
effettuare qualsiasi operazione.
Alimentare il circuito elettrico della pompa Sorriso Clima-SC11 e SCA15,
collegando i li Azzurro e Marrone alla rete elettrica generale, mediante due li di
pari o superiore sezione asservito da un dispositivo di protezione e interruzione
elettrica sulla fase e sul neutro conforme alle normative vigenti. Il cavo non
prevede il collegamento di terra in quanto il circuito è a doppio isolamento . La
pompa Sorriso Clima-SC11 e SCA15 hanno grado di protezione IP20: installare
in ambienti riparati dall'acqua. Non installare in celle frigorifere.
Collegamento elettrico di allarme.
ATTENZIONE!!!ESEGUIRE SEMPRE IL COLLEGAMENTO DI ALLARME
La pompa Sorriso Clima-SC11 e SCA15 dispone di un contatto di allarme C-NO
6A 250Vac ai capi dei li neri. Per il collegamento elettrico, fare riferimento allo
schema elettrico presente in questo foglio istruzioni. Si consiglia di utilizzare il
contatto di allarme per interrompere l’unità esterna (o interna in caso di multisplit).
Cavo alimentazione
Sorriso SC11
Alimentazione cavo
Sorriso SCA15
Fuse: 315mA Rapido
5
L’allarme interviene nei seguenti casi:
1. Mancata alimentazione elettrica al blocco pompa;
2. Guasto del circuito interno del blocco pompa;
3. Intervento del sensore termico di sicurezza presente nella pompa;
4. Raggiungimento del livello di allarme del galleggiante nel serbatoio.
Quando interviene l'allarme, il contatto apre.
Importante! Non interrompere MAI l’alimentazione della mini pompa.
Principio di funzionamento del contatto di Allarme.
ESEGUIRE SEMPRE IL COLLEGAMENTO DI ALLARME
INTERVENTO DELL'ALLARME
cavo Sorriso
PER VERSIONI CON LED DI SEGNALAZIONE
Codici: 12170100L - 12170101L
*ATTENZIONE! LA PRESENZA DEL
LED DI ALLARME NON ESCLUDE IL
COLLEGAMENTO DEI FILI DI ALLARME
GIALLO: ALIMENTAZIONE
VERDE: FUNZIONAMENTO
ROSSO: ALLARME *
6
Solo quando verrà data alimentazione
ai morsetti, il contatto di allarme
commuterà tra C e NO: in questo
modo potrà essere possibile asservire
direttamente l'unità che produce la
condensa.
Se non si intende interrompere
l'alimentazione di tale unità o la serie
termostato, è possibile collegare un
segnale acustico o luminoso asservite
dal relè.
Fino al momento in cui la pompa Sorriso sarà priva di
alimentazione elettrica, il contatto di allarme risulterà assente
tra i capi dei li neri.
GARANZIA
1
2
WARNING! FOR SORRISO MODELS CLIMA-SC11 AND
SORRISO-SCA15 ONLY USE Ø 4 mm x 6 mm PIPE
ONLY USE Ø 4 mm x 6 mm PIPE TO CONNECT THE PUMP TO THE WATER
OUTLET. VERY IMPORTANT!! ALWAYS CONNECT THE ALARM SYSTEM
KEEP THE SORRISO PUMP ON A FLAT SURFACE. THE TILTED POSITION
OF THE PUMP (MORE THAN 10°) PREVENTS THE INTERNAL POLYSTYRENE
FLOAT FROM FREELY SLIDING ALONG ITS SEAT.
USE THE 3 INSERTS AND 3 FIXING SCREWS TO POSITION THE PUMP.
(REFER TO THE DRILLING DIAGRAM TO FIX THEM)
DO NOT THROTTLE THE PIPE, BEND IT. BENDS MUST HAVE A RADIUS
OF AT LEAST 50 mm. THROTTLING AFFECTS THE PUMP’S OPERATION.
CONSIDER THAT EACH PIPE BEND CORRESPONDS TO A HEAD DROP OF
APPROXIMATELY 1 mt.
INSERT THE WHOLE RUBBER COUPLING OF THE PIPE COMING FROM THE
SPLIT SYSTEM’S OUTLET IN THE TANK
FOR THE SCA MODEL, DO NOT USE THE PUMP TO REMOVE CONDENSATE
COMING FROM THE FLUE: USE IT ONLY FOR THE BOILER’S CONDENSATE
ALWAYS CONDUCT ROUTINE MAINTENANCE WHEN THE SEASON STARTS
(BEFORE TURNING ON THE SPLIT SYSTEM OR THE BOILER). OPEN THE
DOOR, TAKE OUT THE TANK AND RINSE IT WITH WATER: RINSE THE FILTER
AS WELL.
AT THE END OF THE SEASON SWITCH OFF THE POWER TO THE PUMP.
3
INSTALLATION AND ACTIVATION
4
ALARM
5
ALWAYS CONNECT THE ALARM SYSTEM
1. There is no power supply on the pump blocking device;
2. In the event of failure of the circuit inside the pump blocking device;
3. When the thermal safety sensor in the pump is tripped;
4. When the alarm level of the oat in the tank is reached.
The contact opens when the alarm is triggered.
Important! NEVER interrupt the mini pump’s power supply.
HOW THE ALARM CONTACT WORKS
6
SORRISO
SC-11 LT
The warranty lasts 2 years from the date of delivery.
The supplier company guarantees the quality of the materials used and the correct
construction of the components. The warranty covers defects in materials and manufacturing
defects and refers to the supply of spare parts of any components featuring defects, without
any compensation, interest or claim for damages.
The warranty does not cover the replacement of components damaged due to: incorrect
transportation; installation not compliant with that specied in this installation, use and
maintenance manual; non-observance of product technical specications; anything else
that is not linked to original faults of the material or production provided that the customer
complaint is covered by the guarantee and a claim is made within the time limit and in
the way requested by the supplier, the same supplier will commit, at their own discretion,
to replace or repair any product or part of product showing signs of faults or defects.
WARRANTY
SORRISO
SCA-15 LT
ITALIANO INGLESE
ITALIANO INGLESE
Tecnosystemi S.p.A. Società Benet
Via dell'Industria 2/4 - z.i. San Giacomo di Veglia
31029 Vittorio Veneto Treviso
Tel. 0438 - 500044 / Fax. 0438 - 501516
N° VERDE 800 904474 (only for Italy)
[email protected] - www.tecnosystemi.com
C.F. - P. IVA - R.I.TV IT02535780247 Cap. Soc. € 5.000.000,00 i.v.
Accessori e Fissaggi
per la Climatizzazione
Barriere d’Aria
ed Accessori
Recuperatori di Calore
ed Accessori per V.M.C.
Componenti per la
Diusione dell’Aria
Strumenti ed
Utensili
Prodotti per
il Riscaldamento
Fissaggi e Accessori
per il Fotovoltaico
Prodotti per la Sanicazione
e per la Protezione Individuale
Sistemi
Gestione Multizona
N°2 FORI A Ø 6MM
N°1 FORO “B” Ø 6MM
1. INSTALLAZIONE CON SPLIT (SORRISO SC15): Posizionare il foglio sulla parete facendolo passare sotto il lato inferiore dello split, allineando la linea “L con la base dello split
INSTALLAZIONE CON CALDAIA (SORRISO SCA15): Posizionare il foglio sulla parete allineando la linea “L al di sotto del sifone
2. Forare nei punti A e “B” (ø 6 mm) in corrispondenza degli interassi indicati a disegno.
3. Inserire a muro i tasselli forniti a corredo e avvitare quasi completamente le viti nei punti A.
4. Agganciare la pompa e traslare secondo il movimento delle asole: serrare le due viti.
5. Completare il della pompa inserendo e serrando la vite nel punto “B”.
1. INSTALLATION WITH SPLIT (SORRISO SC15): Place the sheet on the wall, passing under the bottom side of the split, align the line “L with the base of the split
INSTALLATION ON BOILER (SORRISO SCA15): Place the sheet on the wall lining up the line “L below the siphon
2. Drill holes at points “A and “B” (ø 6 mm) at the center distance in the drawing.
3. Insert to the wall the wall plugs supplied and screw in the screws almost completely at the A” points
4. Hang the pump and move according to the movement of the slots and tighten the two screws.
5. Complete the pump mounting by inserting and tightening the screw at “B” point .
N°2 HOLES “A” Ø 6MM
N°1 HOLE “B” Ø 6MM
Rev.12/2012
SCALA DISEGNO 1:1
SCHEME SCALE 1:1
A
A
B
LL
LINEA INFERIORE DI
BATTUTA DELLO SPLIT
Punto di ingresso acqua di condensa nel serbatoio
The entry point condensate water in the tank
DIMA INSTALLAZIONE :
POMPA SORRISO DA SOTTO SPLIT “SORRISO CLIMA - SC 11 LT.
POMPA PER ACQUA DI CONDENSA ACIDA “SORRISO - SCA 15 LT.
POMPA SORRISO DA SOTTO SPLIT “SORRISO CLIMA LED - SC 11 LT.
POMPA PER ACQUA DI CONDENSA ACIDA “SORRISO LED - SCA 15 LT.
DIMA :
“SORRISO CLIMA - SC 11 LT.” CONDENSATION DRAIN PUMP
“SORRISO - SCA 15 LT.” PUMP FOR ACID CONDENSATION WATER
“SORRISO CLIMA LED - SC 11 LT.” CONDENSATION DRAIN PUMP
“SORRISO LED - SCA 15 LT.” PUMP FOR ACID CONDENSATION WATER
C20001098 - Rev. 07/2017
  • Page 1 1
  • Page 2 2

Tecnosystemi SORRISO LED SCA 15 lt - SORRISO SCA 15 lt under boiler acid condensate water pump Manuale del proprietario

Tipo
Manuale del proprietario