Pottinger SERVO 25 NOVA 3-furrows Istruzioni per l'uso

Operator‘s manual

Translation of the original Operating Manual

Nr. 99+987.EN.80T.0

Plough

SERVO 25

(MaschNr + . . 01001)

SERVO 25 NOVA

(MaschNr + . . 01001)

1500_GB-PAGE 2

Product liability, information obligation

Product liability obliges manufacturers and dealers to issue operating instructions for the machine at the point of sale and to instruct

the customer on the operation, safety and maintenance regulations governing the machine.

A confirmation is required to verify that the machine and operating instructions have been handed over correctly.

For this purpose

- Document A is to be signed and returned to Pöttinger or via the internet to www.poettinger.at

- Document B remains with the specialist dealer handing over the machine.

- The customer receives document C.

For the purposes of product liability law, every farmer is an entrepreneur.

In the terms of product liability law, damage to property is any damage arising due to the machine, but not to the machine, and an

excess (500 euros) exists for this liability.

Corporate damage to property within the terms of the product liability law is excluded from this liability.

Be advised! The operating instructions must also be handed over with any subsequent machine sale or transfer and the transferee

must be instructed in the regulations stated.

Pöttinger - Trust creates Afnity - since 1871

"Quality pays for itself." Therefore we apply the highest quality standards to our products which are constantly monitored by our

in-house quality management and our management board. Because the safety, perfect function, highest quality and absolute

reliability of our machines in operation are the core competencies for which we stand.

There may be deviations between these instructions and the product as we are constantly developing our products. Therefore no

claims may be derived from the data, illustrations and descriptions. Please contact your Specialist Service Centre for any binding

information about specific features of your machine.

We would ask you to please understand that changes to the scope of supply with regard to form, equipment and technical

specifications are possible at any time.

Any form of reprint, translation or reproduction, including excerpts, requires the written approval of Pöttinger Landtechnik GmbH.

All rights according to copyright laws remain expressly reserved by Pöttinger Landtechnik GmbH.

Refer to PÖTPRO for additional information about your machine:

Are you looking for suitable accessories for your machine? No problem! All the information you require is here at your disposal.

Scan the QR code on the machine's type plate or look under www.poettinger.at/poetpro

And if we don't have what your looking for, then your Specialist Service Centre is there for you with help and advice.

GB-0600 Dokum D Servo - 3 -

PÖTTINGER Landtechnik GmbH

Industriegelände 1

A-4710 Grieskirchen

Tel. 07248 / 600 -0

Telefax 07248 / 600-2511

 Check SERVO Turnover Plough as per the delivery docket. Check that delivery is complete.

All safety equipment and operating devices at hand.

 Using the operating manual explain and go over the operation, initial start and maintenance of the machine or

implement with the customer.

 Fitting to the tractor has been carried out.

 Check that hydraulic connections to the tractor have been made and that they are correct.

 Hydraulic functions (turnover, cutting width adjustment) have been demonstrated and explained.

 Plough is set correctly to the tractor (cutting width of 1st component, drawing point).

 Transport and working positions have been explained.

 Information about optional and additional equipment has been given.

 It has been pointed out that to read the operating manual is imperative.

Cross where applicable. X

In accordance with Product Liability obligations, we would ask you to please check the following points.

Confirmation is required to prove that the machine and the operating instructions have been properly handed over. For this purpose you have

received a confirmation e-mail from Pöttinger. If you have not received this mail, please contact your local dealer. Your dealer can fill in the

handover declaration online.

INSTRUCTIONS FOR PRODUCT HANDOVER

EN

- 4 -

1800_GB-INHALT_987

CONTENTS EN

Table of contents

WARNING SIGNS

CE sign ...................................................................... 5

Meaning of warning signs .......................................... 5

ATTACHING TO THE TRACTOR

Preparations on the tractor ........................................ 6

Hydraulic control on the lifting gear ........................... 6

Hydraulic connection ................................................. 7

Preparations on the plough ........................................ 7

Attaching to the tractor ............................................... 8

Removal from tractor ................................................. 8

Garaging, cleaning and winter storage of the

implement ................................................................. 8

Before driving to the field ........................................... 9

Fine setting (Measurement F) .................................. 10

Table for Katt. II ........................................................ 10

OPERATION

Setting the plough to the tractor using ......................11

"Servomatic" .............................................................11

Turning the plough over ........................................... 12

Setting the plough gradient (11) ............................... 12

Ploughing with hydraulic control .............................. 13

OPERATION

ON-LAND Ploughing.................................................14

Conventional ploughing ............................................14

Converting to conventional ploughing .......................14

Converting to "ON-LAND" ploughing ........................14

OVERLOAD SAFETY

Shear bolts ............................................................... 15

SERVO NOVA

Fully automatic "Non-stop" overload safety ............. 16

Setting range ........................................................... 16

Gas tank (43): ...........................................................17

Changing the pressure in the gas tank .....................17

Advice for general maintenance .............................. 18

Cleaning of machine parts ....................................... 18

Hydraulic unit .......................................................... 18

Setting the ploughing component tilt ........................ 19

Basic setting of the ploughing component ............... 19

SERVO 25 ............................................................... 20

ADDITIONAL DEVICES

Setting the disk coulter (* ......................................... 21

Spring loaded disk coulter (* .................................... 21

Pre-ploughing implements ....................................... 21

FEELER WHEELS

Double feeler wheel ................................................. 22

PLOUGH-TRAILING IMPLEMENTS

Extension arm with hydraulic releasing device for

packer and trailing implements ................................ 23

Working with a trailing implement ............................ 23

Disconnect the arm .................................................. 24

Adjusting the amortisation effect.............................. 24

Extension arm with hydraulic releasing device for

packer and trailing implements ................................ 25

Working with a trailing implement ............................ 26

TECHNICAL DATA

Defined use of the plough according to the

manufacturer’s instructions ...................................... 28

Position of Vehicle Identification Plate ..................... 28

Technical data .......................................................... 29

Optional Equipment ................................................. 30

Plough body forms ................................................... 31

Plough body ............................................................. 32

SUPPLEMENT

Lubricants ................................................................ 38

Combination of tractor and mounted implement .......41

9501_GB-WARNBILDER_942

GB

- 5 -

warning signs

CE sign

The CE sign, which is affixed by the manufacturer, indicates outwardly that this machine conforms to the engineering

guideline regulations and the other relevant EU guidelines.

EU Declaration of Conformity (see supplement)

By signing the EU Declaration of Conformity, the manufacturer declares that the machine being brought into

service complies with all relevant safety and health requirements.

Meaning of warning signs

Stay clear of swinging area of

implements

Never reach into the crushing danger area

as long as parts may move.

1000-GB ANBAU_987

GB

- 6 -

aTTaCHing TO THE TraCTOr

Preparations on the tractor

General

Please observe the power range limits of the tractor being used.

Wheels

- Air pressure in the tractor’s rear tyres when ploughing should be 0.8

bar.

- Under difficult operating conditions additional wheel weights can be

advantageous. See the tractor manufacturer’s operating manual also.

Ballast weight

- Sufficient ballast weights are to be stacked on the front

of the tractor in order to guarantee steering and braking

capabilities.

- At least 20% of the tractor’s tare weight on the front axle.

Lifting gear

- Left and right lifting struts (4) must be of equal length.

Adjust using adjusting device (3).

- If the lifting struts on the lower link can be pinned variously, then select

the back position (H). In so doing the tractor’s hydraulic unit will not be

heavily loaded.

- Position (2) the upper link (1) according to the tractor manufacturer’s

information.

Setting-up for transportation

- Fix the lower link with the struts (5) so that the attached implement cannot

swing out during transportation.

- The hydraulic’s operating lever must be secured against lowering.

- Do not transport in the „ON-LAND“ position

Setting-up for ploughing

- Set the struts (5) so that the greatest possible sideways swing range

exists.

Hydraulic control on the lifting gear

Control position:

For mounting and dismounting the implement and for transportation.

The control position is the normal setting for the lifting gear hydraulics.

The mounted implement remains at the height (= position) set by the servo-

valve (ST).

Pull control, mix control:

Ploughing occurs with of one of the two operating modes. See chapter

„OPERATION“ for description.

20%

Kg

ST-24-11-2003

1000-GB ANBAU_987

GB

aTTaCHing TO THE TraCTOr

- 7 -

Hydraulic connection

1 Double-action control unit

Preparations on the plough

Mounting axle 825 mm

• Carryoutadaptiontothetractor´sliftinggear

- both helical plates can be fitted in 4 different positions (P1, P2,

P3, P4)

Upper guide pin

The upper guide pin (B) must be secured with the locking piston (BS)

in every pinning position (L1, L2 and L3) (See table).

The upper guide pin (B) must be secured with the linch pin after

positioning!

Pinning position

Upper guide pin (B) Locking piston (BS)

L1 L2

L2 L1

L3 L2

Beware!

If the upper guide pin (B) is placed in the (L2) position,

the locking piston (BS) must only be placed in pinning

position (L1)! Should the locking piston (BS) be placed in

pinning position (L3) then the upper guide pin (B) will be

damaged because plough swing will be constricted!

161-02-28

L1

L2

L3

BS

B

1000-GB ANBAU_987

GB

aTTaCHing TO THE TraCTOr

- 8 -

TD65/92/27

1

P1

P2

Parking stand

- Using the control lever

(8), release parking

stand, swing up and

back and lay in the clamp

(9).

Lighting and Warning equipment

When travelling in fog, half-light or at night, protruding parts are to be

clearly indicated. Advice on the application of warning signs, reflective

film or paint and lighting units can be found in the instructions for

ancillary equipment in supplement C.

PôTTINGER can supply lighting units and warning signs upon

request.

Always observe the

statutory regulations.

Removal from tractor

Hint: The shear points are hardened so when set down onto hard surface

(stone, concrete, etc.), risk of breaking exists. Therefore lower the

shear points onto a suitable support (wooden board)!

- Turn plough frame to working position and park the implement on

stable and even ground.

- Move the control lever (ST)

back and forth several times

to reduce pressure in the

hydraulic lines.

- Switch tractor’s hydraulics

to control position.

- Disconnect hydraulic hoses

from tractor.

- Using the control lever

(8), release parking stand,

swing down and secure.

- Detach upper and lower links from implement.

Garaging, cleaning and winter storage of the

implement

• Observe the points in the chapter „MAINTENANCE AND

SERVICE“!

8

9

TD65/92/31

Attaching to the tractor

Safety advice:

See supplement A1, Pt. 8a-h

- Switch tractor’s hydraulics to control position.

- Attach implement to lower link and secure with linch pin.

Note

The attaching frame can be positioned horizontally by turning the

tilt spindle (11).

Doing this enables an easier coupling to the lower link.

Then turn the tilt spindle (11) back. See chapter „OPERATION“

also.

Pin upper link (1)

- Pin upper link (1) so that the attachment point (P1) on the plough

during operation is somewhat higher than the attachment point (P2)

on the tractor.

Securing lower link

If the tractor’s hydraulic control

is to be steered over the lower

link, then the upper link should

be positioned in the slot (LL) on

the attaching frame.

Securing upper link

If the tractor’s hydraulic control

is to be triggered over the upper

link, then both the (RL) borings

on the attaching frame are to be used.

- Couple hydraulic hoses to the tractor.

ST-24-11-2003

1900_EN-VOREINSTELLUNG_987

EN

PLOUgH PrEsETTing

- 9 -

Before driving to the field

SERVO

1. Carry out basic setting according to Table A.

2. Carry out exact setting when in operation.

SERVO NOVA

1. Carry out basic setting according to Table B.

2. Carry out a more accurate setting when in use.

Setting cutting width

- Loosen both hexagonal screws (SK).

- Remove rear hexagonal screw.

- Swivel the fastening bracket until the required cutting width is

reached and the hexagonal screw goes into one of the holes (1, 2,

3, 4).

- Retighten the hexagonal screws.

Setting the two spindles (ZP, VF)

Pulling point (ZP)

Backfurrow (VF)

• Thesetting dependsonthe innerdistanceof thetractorwheels

(RA) and the set cutting width (1, 2, 3, 4) .

- More information about pulling point and backfurrow in chapter

"APPLICATION".

RA

TD65/92/35

Table A

for

SERVO 25

1

320/330/350

[mm]

2

360/370/400

[mm]

3

400/410/440

[mm]

4

430/450/480

[mm]

RA

[mm]

ZP

[mm]

VF

[mm]

ZP

[mm]

VF

[mm]

ZP

[mm]

VF

[mm]

ZP

[mm]

VF

[mm]

1,000 463 388 486 381 507 374 525 368

1,100 442 383 466 375 487 368 506 361

1200 420 378 445 370 466 362 486 355

1300 398 374 423 366 445 357 466 349

1400 375 369 401 361 424 352 444 344

1500 --- --- 377 356 401 347 423 339

Table B

for

SERVO 25 NOVA

1

320/330/350

[mm]

2

360/370/400

[mm]

3

400/410/440

[mm]

4

430/450/480

[mm]

RA

[mm]

ZP

[mm]

VF

[mm]

ZP

[mm]

VF

[mm]

ZP

[mm]

VF

[mm]

ZP

[mm]

VF

[mm]

1000 508 401 529 395 --- --- --- ---

1,100 487 395 509 388 530 383 548 379

1200 467 389 490 382 510 375 529 370

1300 446 384 469 376 490 369 510 362

1400 425 380 448 371 470 363 490 356

1500 402 375 427 366 449 358 469 350

165-02-11

ZP

VF

1

4

2

sK

3

1900_EN-VOREINSTELLUNG_987

EN

PLOUgH PrEsETTing

- 10 -

Fine setting (Measurement F)

Fine setting is tuning the plough to the tractor being used and is therefore

only to be carried out once.

In so doing, the fine setting spindle is set at the determined measurement

(F).

- Take the measurements (A) and (B) on the lower linkages and determine

the intersection point according to the table for a Kat. II.

The measurements (A, B) must always be taken from ball centre to ball

centre.

- The position of the intersection point between the diagonal lines on the

table is the setting (F).

Table for Katt. II

Kat. II = 825 mm

W = 80 mm

Example:

A = 416 mm

B = 931 mm

W = 80 mm

(W = 200 mm)

The intersection point lies between lines "306" and "308".

Therefore the intersection point is 307 mm.

F = 307 mm

Setting the adjusting spindle

- Remove bolts (12).

- Set the adjustment spindle to the determined measurement

(F).

- Replace bolts (12).

F

B

A

W

165-02-11

12

0900-GB EINSaTz_987

GB

- 11 -

OPEraTiOn

Setting the plough to the tractor using

"Servomatic"

„SERVOMATIC“ enables the optimum adaption of plough to tractor.

The following setting controls should be carried out in order.

1. Fine setting (F)

- Check setting measurement for fine adjustment spindle (F).

See chapter "PRESETTING THE PLOUGH".

2. Furrow width setting of the first ploughing component

(backfurrow)

The furrow width (S2) of the first ploughing component is set by turning

the spindle (VF).

Furrow width (S1) to narrow

- turn spindle (VF) longer

Furrow width (S2) to wide

- turn spindle (VF) shorter

Furrow width (S2) correct

- Spindle is correctly set according to table.

See chapter "PRESETTING THE PLOUGH“

Incorrect setting

The drawing line does not run through the mid-point of the tractor’s rear

axle. Tractor is drawn into already ploughed area during ploughing. This

can only be compensated by steering in the opposite direction.

- Turn spindle (ZP) longer

See chapter "PRESETTING THE PLOUGH“

3. Setting the drawing point (Z)

Correct setting

The drawing line (ZL) runs through the mid-point (M) of the tractor’s

rear axle. No side pull arises from the tractor.

The plough is easy to pull.

- Spindle (ZP) is set according to the table.

See chapter "PRESETTING THE PLOUGH“

F

B

A

W

165-02-11

12

3

1

4

2

SK



165-02-12

0900-GB EINSaTz_987

GB

OPEraTiOn

- 12 -

Turning the plough over

Beware!

Nobody is to stand within the swinging range during turning.

Turning procedure is only to be actuated from the tractor cabin.

The plough must be completely raised to turn.

The automatic reversing gear enables the whole turning procedure to

be carried out through only one single switch position on the control

unit (ST). (Oil quantity necessary: 40 – 50 l/min)

Turning procedure with a double-action cylinder

- Switch control unit (ST) to lift (h).

The plough is turned 180¯.

- Switch control unit (ST) to neutral (O).

After some 5 seconds another turning procedure can be effected.

Setting the plough gradient (11)

The plough should sit as vertical (90°) as possible to the ground during

ploughing. This position is obtained by turning both spindles (11) as

described below.

- Lift plough 5 - 10 cm

- Actuate control unit (ST) briefly.

The plough turns slightly away from the stop spindle (11).

- Set the gradient using the spindle (11).

- Turn plough back to stop again.

- Proceed with ploughing and check whether the plough sits more vertically

(90°) to the ground through the new setting.

TD 65/92/48

s

h

0

ST

TD 65/92/25

90°

0900-GB EINSaTz_987

GB

OPEraTiOn

- 13 -

Ploughing with hydraulic control

So that the hydraulic control functions properly, the following must

be observed.

- Position upper link (1) so that the attachment point (P1) on the

plough during operation is somewhat higher than the attachment

point (P2) on the tractor.

Pinning the upper link

LL, RL = Pinning position for securing lower link

RL = Pinning position for securing upper link

Details see chapter „ATTACHING TO THE TRACTOR“.

- During operation the plough should lie lengthwise as parallel as

possible to the ground surface.

- The working depth is set with the lifting gear via the servo-valve

firstly.

Depending upon the hydraulic control model, varying ground

resistance when ploughing is passed on to the control servo-valve

via the upper link (1) or both the lower links. The relevant impulse

is then converted causing the lifting gear to lift or lower.

An example: Securing upper link

The plough penetrates deeper into the ground.

This causes the pressure on the control servo-valve via the upper

link to become greater.

As a consequence, the control valve remains switched to lift until

the set working depth is reached again.

Note:

Follow the tractor manufacturer’s operating manual also.

TD65/92/27

1

P1

P2

ST-24-11-2003

- 14 -

0300-GB ON LAND_981

GB

OPERATION

ON-LAND Ploughing

What does "ON-LAND-Ploughing" mean?

• Notractorwheelsinthefurrows

- All wheels travel on unploughed ground.

Advantages of an "ON-LAND-Plough"

• Ground care with "ON-LAND" ploughing.

No tractor wheels in furrows to compress and knead the

ground. Less tractor wheel slippage as with conventional

ploughing in wet conditions.

• Greater swing range

This makes even travelling on unploughed ground with

dual wheels possible.

• Boundary ploughing possibility

To swing the plough away from ground already ploughed

(antiON-LAND position). This enables accurate

ploughing right up to a boundary.

• Conventional Ploughing

The plough can be centred behind the tractor =

conventional ploughing with wheels in the furrows.

KP = conventional ploughing

OP = "ON-LAND" ploughing

Conventional ploughing

Ploughing with wheels in the furrows

Swing plough to behind centre of tractor using hyraulics.

Converting to conventional ploughing

Safety points

• Conversion to be carried on rm level ground

only

• Do not enter the area underneath a raised

plough

• When converting stay off the raised plough

1. Raise plough slightly

- use tractor's lifting gear

2. Pin spindle in (KP) position

- secure bolt with linch pin

3. Re-set drawing point (ZP)

- see chapter "Setting the plough to tractor using

"SERVOMATIC"

Converting to "ON-LAND" ploughing

Safety points

• Conversion to be carried on rm level ground

only

• Do not enter the area underneath a raised

plough

• When converting stay off the raised plough

1. Raise plough slightly

- use tractor's lifting gear

2. Pin spindle in (OP) position

- secure bolt with linch pin

3. Re-set drawing point (ZP)

- see chapter "Setting the plough to tractor using

"SERVOMATIC"

(943) 9200 GB SICHERUNG

GB

- 15 -

OVErLOaD saFETY

Shear bolts

The ploughing components are fastened with shear bolts.

When overloaded the shear bolts break (30) and the ploughing component swings away and up.

- Remove the rest of the shear bolt.

- Loosen hexagonal bolt (31).

- Swing ploughing component back into the working position.

- Insert new shear screws and retighten both bolts.

Take note!

Only use genuine shear bolts (see spare parts list) with the corresponding dimension and quality. Under no circumstances

use bolts with greater or lesser strength.

- 16 -

1600_GB-NOVA_984

GB

SERVO NOVA

Fully automatic "Non-stop" overload

safety

For grounds that are difficult to plough, with stones or

other foreign bodies, it is recommended to use the fully

automatic overload safety.

With the SERVO-NOVA plough, every plough body

is secured individually against deteriorating by hydro-

mechanical means.

When driving over obstacle, the plough body can swing

to either side. There is no need to stop the tractor. The

plough body swings back to working position by itself.

In addition to the fully automatic "Non-stop" overload

safety, all plough bodies are protected by a shearbolt.

See chapter "OVERLOAD SAFETY“ for a description.

Setting range

• The

triggering

force

of

the

overload

safety

can

be

adjusted function of the various ground types.

N

ormal setting

-

The pressure on the hydraulic cylinders (40) must be

approx. 10 bar higher than the nitrogen pressure in the

gas tank (43).

N

itrogen pressure in the gas tank (43) (factory

setting)

80 bar

S

etting range for the pressure in the hydraulic

cylinders (40)

90 to 160 bar

If you see during practical operation that the overload

safety triggers too often, you can increase the pressure

(

*

in the hydraulic cylinders with the accompanying top-up

device (42) (see table).

Pres

-

sure

(

*

Triggering

force

( bar )

( kp )

90

1010

100

1125

110

1240

120

1350

130

1460

140

1575

150

1690

160

1800

I

ncreasing pressure in the hydraulic cylinders:

-

Stopcock in position

A.

-

Unscrew the sealing cap (41) on the stopcock and top-

up pipe.

-

Depressurise the control valve on the tractor.

-

Connect the plug-in connection (42) on the tractor.

-

Open stopcock (position E). The hydraulic pressure

drops.

-

Operate the control valve on tractor until the gauge

indicates the target pressure. Then close the shut-off

valve (position A).

Beware!

The stopcock must always be closed during

ploughing (position

A).

-

Depressurise the top-up pipe by means of the control

valve.

-

Take out the top-up pipe and screw back the sealing

cap (41).

- 17 -

1600_GB-NOVA_984

SERVO NOVA GB

Gas tank (43):

The pressure in the gas tank can also be changed.

Reducing or increasing the gas pressure in the tank

depends on the various types of ground.

• Incaseofverylightground,youcanreducethegas

pressure to a certain extent.

Be advised!

No welding, soldering or mechanical work

may be performed on the gas container.

Changing the pressure in the gas tank

This operation may be performed only

by the customer service or a special-

ised workshop.

To reduce or increase the preload

pressure, you need a special filling

and verification device.

1. Release pressure:

a) Take out the plastic cover.

- Take out the lead mould plug (if available) in the gas

filling plug (44) with the help of a sharp tool.

b) Loosen the gas filling plug (44) only slightly.

c) Screw on the filling and verification device.

d) Open the evacuation cock on the filling device slightly.

Let out the nitrogen (N) slowly until the gauge has

reached the target pressure.

e) Close the evacuation cock, take out the filling device,

tighten the gas filling plug and put back the lead mould

plug (if provided).

2. Increase pressure:

For tank filling only use nitrogen (N), no

oxygen (danger of explosion).

f) Connect the filling device onto the nitrogen bottle.

g) Take out the plastic cap.

- Take out the lead mould plug (if available) in the gas

filling plug (44) with the help of a sharp tool.

- Loosen the gas filling plug (44) only slightly.

- Screw on the filling and verification device.

h) Screw the verification device onto the nitrogen bottle.

i) Open the evacuation cock on the filling device slightly

and fill with nitrogen until the gauge reads the target

pressure.

k) Close evacuation cock, take out the filling device, tighten

the gas filling plug and put back in the lead mould plug

(if available).

Note

All gas accumulators show a slight pressure drop after a

certain period of time, according to "HYDAC" factory

specifications.

The gas loss amounts to approx. 2-3 % pa.

It is recommended to check and if necessary correct tank

pressure after 4-5 years.

- 18 -

1800_EN-Wartung_955

EN

MAINTENANCE

Advice for general maintenance

In order to keep the implement in good condition even after

a long service life, please observe the following points:

-Retighten all screws after the first hours of operation.

During the operating season

- Check all screws occasionally and retighten if necessary.

- Oil joints and adjusting spindle once a week.

Wearing parts

- Replace worn out expendable parts in time to prevent any

stress-bearing parts from becoming damaged.

Tyre pressure

- Pay attention to the correct tyre pressure!

Check tyre pressure regularly!

• Danger of bursting when pumping up or

when tyre pressure is too great!

Cleaning of machine parts

Be advised!

Do not use a high pressure cleaner to clean bearings

and hydraulic parts.

-Danger of rust!

-Lubricate the machine after cleaning and carry out a

short trial run.

-Cleaning with too high pressure may damage the paint.

Parking in the open

When parking in the open for

longer periods, clean piston

rods and then preserve with

grease.

Winter storage

- Thoroughly clean the

machine beforehand.

- Put up weather protection.

- Protect exposed parts from rust.

- Lubricate all greasing points according to lubrication chart.

Hydraulic unit

- Check hydraulic hoses regularly for damage.

Immediately replace porous or damaged hydraulic

hoses.

Caution danager of infection!

• If there are defects in the hydraulic unit, do

not touch areas of leakage.

Before working on the hydraulic unit

- lower implement to the ground.

- When carrying out maintenance work on a raised

implement always secure it with a suitable support.

- Depressurize the hydraulic unit and turn the motor off.

FETT

TD 49/93/2

Note:

The lubrication

points and the

frequency of lubri-

cation are stated

in the lubrication

chart at the end of

this Chapter.

- 19 -

1800_EN-Wartung_955

EN

MAINTENANCE

Basic setting of the ploughing component

Checks must be made in the following order after replacing worn out parts:

1. Stand the plough on even ground.

2. The gap (A) between plough and share cutting edge must be the same for all ploughing components.

3. Check the gap (B1) on the last ploughing component.

B1 = 0 - 5 mm for ploughing components* of the type W, UWS

10 - 20 mm for ploughing components* of the type UW, UWS, WSS

4. Set the same measurement for gap (B) as for B1.

* The type of plough body is shown clearly on the manufacturer’s plate.

Setting the ploughing component tilt

If the plough is not penetrating the ground correctly, an

improvement can be obtained by turning the eccentric bush.

•Thebladepointinthearea„S“isseteitherhigher or

lower depending upon the position of the eccentric

bush (A or B).

•Retightenscrewsafterresetting.

On some models a catch plate is fitted instead of an

eccentric bush.

See "Basic setting of the ploughing component" also.

- 20 -

1800_Schmierplan_9832

SERVO 25

10h

1

2

22 1

1 2

076-18-007

1

2

4

076-18-008

10 h

1

La pagina sta caricando ...

Pottinger SERVO 25 NOVA 3-furrows Istruzioni per l'uso

Pottinger SERVO 25 NOVA 3-furrows Istruzioni per l'uso

in altre lingue

Documenti correlati

Altri documenti