Philips HX6973/53 Manuale utente

FlexCare+

900+ series

Rechargeable

sonic toothbrush

1

2

3

4

5

6

7

8

9

10

11

14

13

12

1

English 6

Deutsch 21

Español 40

Français 57

Italiano 75

Nederlands 92

Português 110

Ελληνικα

128

English

Introduction

Congratulations on your purchase and welcome to Philips! To fully

benefit from the support that Philips offers, register your product at

www.philips.com/welcome.

Important

Read this user manual carefully before you use the appliance and

save it for future reference.

Danger

-

Keep the charger away from water. Do not

place or store it over or near water

contained in a bathtub, washbasin, sink etc.

Do not immerse the charger in water or any

other liquid. After cleaning, make sure the

charger is completely dry before you

connect it to the mains.

Warning

-

The mains cord cannot be replaced. If the

mains cord is damaged, discard the charger.

-

Always have the charger replaced with one

of the original type in order to avoid a

hazard.

-

Do not use the charger outdoors or near

heated surfaces.

6

English

-

If the appliance is damaged in any way

(brush head, toothbrush handle or charger),

stop using it. This appliance contains no

serviceable parts. If the appliance is

damaged, contact the Consumer Care

Centre in your country (see chapter

‘Guarantee and support').

-

This appliance can be used by children aged

from 8 years and above and by persons with

reduced physical, sensory or mental

capabilities or lack of experience and

knowledge if they have been given

supervision or instruction concerning use of

the appliance in a safe way and if they

understand the hazards involved. Children

shall not play with the appliance. Cleaning

and user maintenance shall not be made by

children unless they are older than 8 and

supervised.

Caution

-

Do not clean the brush head, the handle,

the charger, the charger cover and/or the

sanitizer in the dishwasher.

7

English

-

If you have had oral or gum surgery in the

previous 2 months, consult your dentist

before you use the toothbrush.

-

Consult your dentist if excessive bleeding

occurs after using this toothbrush or if

bleeding continues to occur after 1 week of

use.Also consult your dentist if you

experience discomfort or pain when you use

the Philips Sonicare.

-

The Philips Sonicare toothbrush complies

with the safety standards for

electromagnetic devices. If you have a

pacemaker or other implanted device,

contact your physician or the device

manufacturer of the implanted device prior

to use.

-

If you have medical concerns, consult your

doctor before you use the Philips Sonicare.

-

This appliance has only been designed for

cleaning teeth, gums and tongue. Do not

use it for any other purpose. Stop using the

appliance and contact your doctor if you

experience any discomfort or pain.

8

English

-

The Philips Sonicare toothbrush is a

personal care device and is not intended for

use on multiple patients in a dental practice

or institution.

-

Stop using a brush head with crushed or

bent bristles. Replace the brush head every

3 months or sooner if signs of wear appear.

-

Do not use other brush heads than the ones

recommended by the manufacturer.

-

If your toothpaste contains peroxide, baking

soda or bicarbonate (common in whitening

toothpastes), thoroughly clean the brush

head with soap and water after each

use.This prevents possible cracking of the

plastic.

-

Do not insert objects into the air openings of

the sanitizer or block these air openings by

placing it on a soft surface or in a position or

location where objects will block these

openings (examples of objects: magazine,

tissue paper and hair).

9

English

-

The UV light bulb is hot during and

immediately after the sanitizing cycle. Do

not touch the UV light bulb when it is hot.

-

Do not operate the sanitizer without the

protective screen in place to avoid contact

with a hot bulb.

-

If the sanitizer has been used for 3

consecutive UV clean cycles (i.e. 3 times in a

row), switch it off for at least 30 minutes

before you start another UV clean cycle.

-

Discontinue use of the sanitizer if the UV

light bulb remains on when the door is

open. UV light can be harmful to the human

eye and skin. Keep the sanitizer out of the

reach of children at all times.

Electromagnetic fields (EMF)

This Philips appliance complies with all applicable standards and

regulations regarding exposure to electromagnetic fields.

General description (Fig. 1)

1 Hygienic travel cap

2 Brush head with unique identifier

3 Handle

4 Power on/off button

5 Intensity level indicator

6 Intensity level button (+ and -)

7 Brushing modes

10

English

8 Mode button

9 Battery level indicator

10 UV sanitiser base with integrated charger and cord wrap (specific

types only)

- Not shown: UV light bulb

- Not shown: Sanitizer drip tray

- Not shown: Protective screen for UV light bulb

11 Mains cord with plug

12 Charger cover with brush head holders (select models)

13 Travel charger

- Not shown: Travel case

The content of the box may vary based on the model purchased.

Preparing for use

Changing the colour code ring (for select models)

Sonicare brush heads come with interchangeable colour code rings to

identify your brush head.

To change the colour code ring:

1 Pull the colour code ring from the bottom of the brush head.

2 Install a new ring by slipping one edge of the new ring over the

bottom of the brush head.

Attaching the brush head

1 Align the brush head so the bristles point in the same direction as

the front of the handle. (Fig. 2)

2 Firmly press the brush head down onto the metal shaft until it

stops.

Note: There is a small gap between the brush head and the

handle.

Charging the appliance

1 Put the plug of the charger or sanitizer in a wall socket.

2 Place the handle on the charger or sanitiser.

11

English

The flashing light of the battery level indicator indicates that the

toothbrush is charging. (Fig. 3)

-

1 solid green LED indicates that the toothbrush is 34-66%

charged.

-

2 solid green LEDs indicate that the toothbrush is 67-94%

charged.

-

3 solid green LEDs indicate that the toothbrush is fully charged.

Note: If the battery charge of your Philips Sonicare is low, you hear 3

beeps and 1 LED of the recharge gauge flashes yellow for 30 seconds

after completing the brushing cycle.

Note: To keep the battery fully charged at all times, you may keep

your Philips Sonicare on the charger when not in use. Once the

Philips Sonicare is fully charged, the charger draws minimal energy

from the wall socket.

Note: It takes at least 24 hours to fully charge the battery.

Using the appliance

Brushing instructions

1 Wet the bristles (Fig. 4) and apply a small amount of toothpaste

(Fig. 5). (Fig. 4)

2 Place the toothbrush bristles against the teeth at a slight angle (45

degrees), pressing firmly to make the bristles reach the gumline or

slightly beneath the gumline. A change in vibration (and a slight

change in sound) alerts you when you apply too much pressure

while brushing. (Fig. 6)

Note: Keep the center of the brush in contact with the teeth at all

times.

3 Press the power on/off button to switch on the Philips Sonicare.

(Fig. 7)

4 Apply light pressure to maximize Philips Sonicare’s effectiveness

and let the Philips Sonicare toothbrush do the brushing for you.

Do not scrub.

12

English

5 Gently move the brush head slowly across the teeth in a small

back and forth motion so the longer bristles reach between your

teeth (Fig. 8). Continue this motion throughout the brushing cycle.

6 To clean the inside surfaces of the front teeth, tilt the brush handle

semi-upright and make several vertical overlapping brushing

strokes on each tooth (Fig. 9).

7 Begin brushing in section 1 (outside upper teeth) and brush for 30

seconds (45 seconds in Deep Clean mode) before you move to

section 2 (inside upper teeth). Continue brushing in section 3

(outside lower teeth) and brush for 30 seconds (45 seconds in

Deep Clean mode) before you move to section 4 (inside lower

teeth (Fig. 10)).

Note: To make sure you brush evenly throughout the mouth, divide

your mouth into 4 sections using the Quadpacer feature (see chapter

‘Features’).

Note:After you have completed the brushing cycle, you can spend

additional time brushing the chewing surfaces of your teeth and

areas where staining occurs. (Fig. 11) You can also brush your tongue,

with the toothbrush turned on or off, as you prefer.

Your Philips Sonicare is safe to use on:

- Braces (brush heads wear out sooner when used on braces).

- Dental restorations (fillings, crowns, veneers).

Brushing modes

Philips Sonicare automatically starts in the default Clean mode.

1 Prior to switching on the Philips Sonicare, press the mode button

to toggle between modes.

-

The selected brushing mode illuminates.

-

Once a brushing mode has been selected, it remains active

until another brushing mode is selected.

Note: When the toothbrush is switched on, you cannot toggle

between modes.

The following brushing modes are available:

Clean Complete whole mouth cleaning (2 minutes).

13

English

Gum Care Complete whole mouth cleaning (2 minutes) plus gentle

cleaning for problem areas and along the gumline (1 minute).

Refresh (select models) Touch-up for a quick clean (1 minute).

Sensitive Gentle cleaning for sensitive gums and teeth (2 minutes).

Massage (select models) Gentle gum stimulation (2 minutes).

White 2 minutes of Clean mode, with an additional 30 seconds of

White mode to focus on your visible front teeth.

Note: When Sonicare is used in clinical studies, the default 2-minute

Clean mode must be selected. The handle has to be fully charged.

Deactivate the Easy-start feature. For areas where excess staining

occurs, an additional 30 seconds of brushing time can be spent to

help remove stains.

Features

Easy-start

The Easy-start feature gently increases power over the first 14

brushings to help you get used to brushing with the Philips Sonicare

toothbrush. This Philips Sonicare toothbrush comes with the Easy-

start feature activated.

Activating or deactivating the Easy-start feature

1 Attach the brush head to the handle.

2 Place the handle in the plugged-in charger.

- To deactivate Easy-start:

Press and hold the power on/off and mode button for 5 seconds.

You hear 1 beep to indicate that the Easy-start feature has been

deactivated.

- To activate Easy-start:

14

English

Press and hold the power on/off and mode button for 5 seconds.

You hear 2 beeps to indicate that the Easy-start feature has been

activated.

Note: Using the Easy-start feature beyond the initial ramp-up period

is not recommended and reduces Philips Sonicare effectiveness in

removing plaque.

Note: Easy-start feature is only active in Clean Mode.

Smartimer

The Smartimer indicates that your brushing cycle is complete by

automatically turning off the toothbrush at the end of the brushing

cycle.

Dental professionals recommend brushing no less than 2 minutes

twice a day.

Quadpacer

- The Quadpacer is an interval timer that has a short beep and

pause to remind you to brush the 4 sections of your mouth.

Depending on the brushing mode you have selected, the

Quadpacer beeps at different intervals during the brushing cycle.

See ‘Brushing modes’ in chapter ‘Using the appliance’.

The Quadpacer feature on this model has been activated. To

deactivate or reactivate the Quadpacer feature:

1 Place the handle with a brush head attached on the plugged-in

charger.

2 Press and hold the mode button until:

a You hear 1 beep to indicate that the Quadpacer has been

deactivated.

b You hear 2 beeps to indicate that the Quadpacer has been

activated.

Cord wrap on deluxe charger (specific types only)

If your type includes the deluxe charger cover and base, the travel

charger is pre-installed inside the cover. If you want to shorten the

mains cord, you can store excess cord in the cord wrap feature built

into the charger base.

15

English

1 To separate the charger cover from the charger base, press the

two grey snap bars on the charger base and pull the white charger

cover upwards.

2 Wrap excess power cord around the grey charger base as shown in

the picture. Be sure to wrap the cord on the inside of the two snap

levers.

3 When you have stored the excess cord, guide the mains cord

through the small groove in the rear of the grey charger base.

4 To reattach the charger cover, press it down over the charger base

until it snaps into place.

Tip: For extra convenience during travel, you can remove the travel

charger and use it without the charger cover and charger base.

Cord wrap on sanitiser with integrated charger

(specific types only)

If your type includes the sanitiser, you can store excess cord in the

cord wrap feature built into the bottom of the sanitiser.

Sanitising (specific types only)

- With the UV sanitizer you can clean your brush head after every

use (Fig. 12).

Unplug the sanitizer, discontinue use and call Consumer Care if:

- The UV light bulb remains on when the door is open.

- The window is broken or missing from the sanitizer.

- The sanitizer gives off smoke or a burning smell while it is

operating.

Note: UV light can be harmful to the human eye and skin. This device

should be kept out of reach of children at all times.

1 After brushing, rinse the brush head and shake off excess water.

Warning: Do not place the travel cap on the brush head

during sanitization.

2 Place your finger in the door recess on top of the sanitizer and pull

open the door (Fig. 13).

3 Place the brush head on one of the 2 pegs in the sanitizer with the

bristles facing the light bulb (Fig. 14).

16

English

Note: Only clean Philips Sonicare snap-on brush heads in the

sanitizer.

Note: Do not clean Philips Sonicare for Kids brush heads in the

sanitiser.

4 Make sure the sanitizer is plugged into a live outlet of appropriate

voltage.

5 Close the door and press the green power on/off button once to

select the UV clean cycle.

Note: You can only turn on the sanitizer if the door is properly

closed.

Note: The sanitizer stops if you open the door during the sanitizing

cycle.

Note: The sanitizer cycle runs for 10 minutes and then

automatically shuts off.

-

The sanitizer is in operation when the light glows through the

window.

Cleaning

Warning: Do not clean the brush head, handle, travel charger

or the UV sanitizer in the dishwasher.

Toothbrush handle

1 Remove the brush head and rinse the metal shaft area with warm

water. Make sure you remove any residual toothpaste (Fig. 15).

Caution: Do not push on the rubber seal on the metal shaft with

sharp objects, as this may cause damage.

2 Wipe the entire surface of the handle with a damp cloth.

Brush head

1 Rinse the brush head and bristles after each use (Fig. 16).

2 Remove the brush head from the handle and rinse the brush head

connection with warm water at least once a week.

17

English

Sanitiser (specific types only)

Warning: Do not immerse the sanitiser in water or rinse it

under the faucet.

Warning: Do not clean the sanitiser when the UV light bulb is

hot.

For optimal effectiveness, it is recommended to clean your sanitiser

weekly.

1 Unplug the sanitiser.

2 Pull the drip tray straight out. Rinse the drip tray and wipe it clean

with a damp cloth (Fig. 17).

3 Clean all interior surfaces with a damp cloth.

4 Remove the protective screen in front of the UV light bulb (Fig. 18).

To remove the screen, grasp the edges next to the snaps, gently

squeeze and pull out the protective screen.

5 Remove the UV light bulb.

To remove the light bulb, grasp it and pull it out of the metal clasp.

6 Clean the protective screen and the UV light bulb with a damp

cloth.

7 Reinsert the UV light bulb.

To reinsert the light bulb, align the bottom of the light bulb with

the metal clasp and push the bulb into the clasp.

8 Reinsert the protective screen.

To reinsert the screen, align the pegs on the screen with the slots

on the reflective surface near the UV light bulb. Push the screen

straight into the slots on the sanitiser.

Storage

If you are not going to use the product for a long time, unplug it, clean

it (see chapter 'Cleaning') and store it in a cool and dry place away

from direct sunlight. You can use the integrated cord wrap to store

excess cord of the UV sanitizer in an organized manner.

18

English

Replacement

Brush head

- Replace Philips Sonicare brush heads every 3 months to achieve

optimal results.

- Use only Philips Sonicare replacement brush heads.

UV light bulb

Replacement UV bulbs are available through the Philips Consumer

Care Centre in your country.

Recycling

- This symbol means that this product shall not be disposed of with

normal household waste (2012/19/EU) (Fig. 22).

- This symbol means that this product contains a built-in

rechargeable battery which shall not be disposed of with normal

household waste (Fig. 23) (2006/66/EC). We strongly advise you to

take your product to an official collection point or a Philips service

center to have a professional remove the rechargeable battery.

- Follow your country’s rules for the separate collection of electrical

and electronic products and rechargeable batteries. Correct

disposal helps prevent negative consequences for the

environment and human health.

Removing the rechargeable battery

Warning: PLEASE NOTE THAT THIS PROCESS IS NOT

REVERSIBLE.

- To remove the rechargeable battery, you need a flat-head

(standard) screwdriver. Observe basic safety precautions when you

follow the procedure outlined below. Be sure to protect your eyes,

hands, fingers, and the surface on which you work.

1 To deplete the rechargeable battery of any charge, remove the

handle from the charger, turn on the Philips Sonicare and let it run

until it stops. Repeat this step until you can no longer switch on

the Philips Sonicare.

19

English

2 Insert a screwdriver into the slot located at the bottom of the

handle and turn counterclockwise to release the bottom cap (Fig.

19).

3 Hold the handle upside down and push down on the shaft to

release the internal components of the handle (Fig. 20).

4 Insert the screwdriver under the circuit board, next to the battery

connections, and twist to break the connections. Remove the

circuit board and pry the battery from the plastic carrier (Fig. 21).

The rechargeable battery can now be recycled and the rest of the

product discarded appropriately.

Warranty and support

If you need information or support, please visit

www.philips.com/support or read the international warranty leaflet.

Warranty restrictions

The terms of the international warranty do not cover the following:

- Brush heads.

- Damage caused by use of unauthorized replacement parts.

- Damage caused by misuse, abuse, neglect, alterations or

unauthorized repair.

- Normal wear and tear, including chips, scratches, abrasions,

discoloration or fading.

20

English

La pagina sta caricando ...

Philips HX6973/53 Manuale utente

Questo manuale è adatto anche per

Philips HX6973/53 Manuale utente

in altre lingue

Documenti correlati

Altri documenti