Yamaha V1 Manuale utente

Marca: Yamaha

Modello: V1

Categoria: Attrezzatura musicale

Tipo: Manuale utente

Questo manuale è adatto anche per

PM5D system software V1.20 includes the following changes and additions relative to V1.04 (changes up to V1.12 are also included).

Use ENCODER [ON] keys to turn phan-

tom power (+48V) on/off (from V1.05)

A “USE ENCODER-ON AS +48V” option has been added

to the PREFERENCE 1 screen. If this option is on, and HA

(head amp input sensitivity) is selected as the encoder

mode, you can use the ENCODER [ON] key located above

each encoder to turn phantom power supply (+48V) on/off.

Switch parameter value indication on/

off in the Name display (from V1.05)

A “CHANNEL NAME NUMERIC DISPLAY” field has been

added to the PREFERENCE 2 screen. In V1.04 and earlier,

operating the fader or encoder (pan setting) of each chan-

nel caused the name display to show the value of that

parameter. In V1.05 and later, turning the “ENCODER

VALUE” and “FADER VALUE” options off will prevent the

respective parameter value from appearing when you oper-

ate the fader or encoder.

Select the monitor source from the

panel (from V1.05)

When selecting a monitor source from the panel in V1.04 or

earlier, you could simultaneously select one source from

[2TR A1]–[2TR D3] or [DEFINE] and one source from

[STEREO A]/[STEREO B] (including LCR), for a maxi-

mum total of two sources. In V1.05 and later, turning on

one key will turn off the other keys, allowing you to select a

single monitor source more rapidly. If you want to select

two sources simultaneously (as in V1.04 and earlier), press

the corresponding panel keys simultaneously, or use the

MONITOR screen.

HA follows Recall Safe on/off operations

(from V1.05)

A new SAFE KEY MODE SELECT section has been added

to the RECALL SAFE screen. If you turn on the HA+CH

button, using the [RECALL SAFE] key of the panel or the

RECALL SAFE button in the CH VIEW screen (INPUT

VIEW function) to turn Recall Safe on/off will now also

turn on/off the Recall Safe setting for the HA patched to the

corresponding channel. If the CH button is on, the HA

Recall Safe setting will not be linked.

DCA group name Recall Safe and Selec-

tive Recall can be switched on/off (from

V1.05)

A new WITH NAME button has been added to the DCA

area of the RECALL SAFE screen and SELECTIVE RECALL

screen. This allows you to exclude just the DCA group name

from DCA group Recall Safe and Selective Recall. If the

WITH NAME button is on, Recall Safe and Selective Recall

will apply to the DCA group names of DCA groups for

which these functions are on. If the WITH NAME button is

off, DCA group names are excluded from Recall Safe and

Selective Recall.

PM5D V1.20 Supplementary Manual

Displaying output channel names (from

V1.20)

The OUTPUT PATCH function now includes a NAME

screen that enables you to name output channels and view

channel names on various screens.

The procedure functions the same as the NAME screen for

the INPUT PATCH function.

However, the NAME screen is not included in the CH

COPY, GLOBAL PASTE, or CSV IMPORT/EXPORT

function.

Parameter operation for Recall Safe/

Selective Recall (from V1.12)

When using Recall Safe or Selective Recall, there has been a

change in the behavior of parameters of which only one

exists for each pair of adjacent odd-numbered/even-num-

bered channels or modules (see owner's manual p.165). If

Recall Safe or Selective Recall is specified for only one of

these channels or modules, the parameters will behave as

follows.

• PAIR

Forcibly turned off (pairing will be defeated).

• GATE STEREO LINK

• COMP STEREO LINK

• GEQ LINK

LINK parameters will be forcibly turned off (link will be

defeated).

• DELAY GANG

• ATT GANG

GANG parameters will be recalled. If GANG turns On

because of the recall, the relative differences of the

DELAY and ATT parameter values following the recall

will be maintained when they are edited.

• MS DECODE

• FIXED/VARI

These will not be recalled.

• PAN MODE

The PAN MODE parameter will be recalled. However, if

the recall would cause the PAN MODE setting to change

from BALANCE to some other setting, or from some

other setting to BALANCE, then the PAN MODE and

PAN parameters will not be recalled. Also, if the recall

causes the PAN MODE to become GANG PAN, the rel-

ative difference of the PAN parameter values following

the recall will be maintained when they are edited.

Support for the Y96K card (from V1.10)

A PLUG-IN screen has been added to the EFFECT func-

tion. Also, PLUGIN parameters have been added to the

RECALL SAFE screen and SELECTIVE RECALL screen of

the SCENE function. These additions are in order to sup-

port the Y96K card that will become available in the near

future from the Waves Corporation. For details on opera-

tion, refer to the owner’s manual for the Y96K.

Please note that the Y96K card will operate as follows.

• Data will be stored/recalled as scene data, but the Undo

function is not supported.

• If you power-off and then power-on the PM5D, con-

ventional scene data will be in the same state as when

you powered-off, but the Y96K will be in the state that

was last stored or recalled.

• If you recall a scene that produces a major change in the

settings of the Y96K, the settings of the Y96K will change

several seconds after recall occurs on the PM5D. If you

want the timing of the change to be synchronized, use

the FADE TIME screen to specify a START OFFSET.

• Do not perform scene store/recall operations in the

Y96K’s update waiting screen. If you do so, the screen

will become inoperable for up to 30 seconds.

• The Scene Store operation saves the Y96K settings in the

PM5D. If you executed Scene Store while the Y96K had

previously been installed, and then once again store the

scene with the Y96K not installed, the previous Y96K

settings will remain. If a scene has never been stored

while the Y96K is installed, recalling that scene with the

Y96K installed will not affect the Y96K in any way.

• In PREVIEW mode, the PLUG-IN screen does not dis-

play the Y96K status.

MIDI EVENT etc. data now maintained

during scene recall (from V1.05)

The MIDI EVENT, GPI OUT CONTROL, and REMOTE

TRANSPORT data included in a scene is now maintained

when a scene recall occurs. This means that if you store a

recalled scene into another scene, this data will be stored as

it was when recalled.

DME series monitor source selection and

EXTERNAL CUE on/off (from V1.05)

A MONITOR button and monitor source select button have

been added to the DME CONTROL screen. When you click

the monitor source select button ( ), the MONITOR

POINT SELECT window will appear, letting you select the

DME series unit monitor source. If the MONITOR button

is on, the EXTERNAL CUE indicator in the upper part of

the display will turn on, and the monitor signal of the DME

series unit will be sent to the PM5D’s CUE bus.

Note

Before turning on the MONITOR button, you must select the

same port as the monitor output on the DME series unit and

as the monitor input for the PM5D. To specify the DME series

unit monitor output, use the “Monitor Out” dialog box of DME

Designer, accessed by [Tools] menu

→

[Monitor]. To specify

the PM5D monitor input, use the MONITOR PORT field on the

SETUP page of the DME CONTROL screen.

Much faster DME control (from V1.20)

The speed of remote control operation of the DME64N/24N

(firmware version 2.0 or later) has been increased.

(In particular, speed is increased when a connection is made

via an MY16-C or MY16-CII card.)

The speed of remote control operation of the DME8i-C/

8o-C/4io-C has also been increased.

Newly added bulk dump data types

(from V1.05)

The following data types can now be handled by bulk dump.

SETUP data compatibility (from V1.05)

SETUP data created on system software V1.05 or later can-

not be loaded into a system that’s running V1.03 or earlier.

However, SETUP data created on system software V1.03 or

earlier can be loaded by a system that’s running V1.05 or

later.

Scene data compatibility (from V1.10)

In conjunction with Y96K card support, compatibility of

scene data (ALL DATA, SCENE MEMORY, SCENE MEM-

ORY with LINKED LIBRARY) has been changed as follows.

Scene data created with system software V1.10 or later can-

not be loaded into a system running V1.04 or earlier.

However, scene data created on a system running V1.04 or

earlier can be loaded into a system running V1.10 or later.

In this case, the Y96K settings will remain as they were prior

to loading. If you save this data on a system running V1.10

or later, the data size will increase by the amount required

for Y96K support.

A note regarding scenes/libraries imme-

diately after system startup

After the system is started up, the PM5D takes several min-

utes to transfer scene/library data within internal memory.

(The time required depends on the amount of data.) This

means that the following restrictions apply during this time.

• You can’t execute the PASTE button in the GLOBAL

PASTE screen.

• You can’t execute the scene memory UNDO function.

• Scene memory recall will take a bit of time.

Data name

(D0)

Data Number

(D1,2)

tx/rx Function

‘K’

512

(Current Data)

tx/rx

Surround Setting

& Request

‘V’

512-

(Current Data)

tx/rx

User Defined Keys

& Request

‘L’

512-

(Current Data)

tx/rx

MIDI Remote &

Request

‘U’

512-

(Current Data)

tx/rx

Fader Mode &

Request

U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation

List of parameters available for Pair or Recall Safe operation

The following table illustrates which parameters for the paired channels can be linked and which settings for each parameter can

be selected for Recall Safe operation.

: Parameters of paired channels are linked.

–:Parameters cannot be linked, or selected for Recall Safe operation.

■

Input channels

■

MIX channels

■

MATRIX channels

■

STEREO channels

■

Other

* The parameter becomes eligible for Recall Safe if the

library link is turned off in the SCENE screen.

Parameter

Pair Recall Safe

Recall Safe —

GANG

possible

on HA

HA (not ALL)

NAME

—

PHASE — INPUT ALL

MS DECODE — INPUT ALL

LCR INPUT ALL

Fade Time INPUT FADER, ALL

Insert INPUT ALL

Direct Out INPUT ALL

On INPUT ALL

Fader INPUT FADER, ALL

PA N GANG INPUT ALL

Att GANG INPUT ATT, ALL

Gate INPUT GATE, ALL

Comp INPUT COMP, ALL

HPF INPUT EQ, ALL

EQ INPUT EQ, ALL

Delay On INPUT DELAY, ALL

Delay TIME GANG INPUT DELAY, ALL

Surround LFE INPUT ALL

Surround Div INPUT ALL

Surround Div Rear INPUT ALL

Surround Div Link INPUT ALL

Mute Assign INPUT ALL

DCA Assign INPUT ALL

To Stereo On INPUT ALL

To Mix Follow Pan INPUT MIX SEND, ALL

To Mix ON INPUT MIX SEND, ALL

To Mix LEVEL INPUT MIX SEND, ALL

To Mix PAN INPUT MIX SEND, ALL

To Mix PRE/POST INPUT MIX SEND, ALL

PAIR INPUT ALL

Global Paste —

Solo Safe —

Cue —

Key In Cue —

Mute Safe —

Selective Recall —

Tracking Recall —

Parameter

Pair Recall Safe

Recall Safe —

LCR MIX ALL

Fade Time MIX FADER, ALL

Insert MIX ALL

On MIX ALL

Fader MIX FADER, ALL

BALANCE — MIX ALL

Comp MIX COMP, ALL

EQ MIX EQ, ALL

Delay On MIX DELAY, ALL

Delay TIME GANG MIX DELAY, ALL

Mute Assign MIX ALL

DCA Assign MIX ALL

To Mix ON CH to MIX (not ALL)

To Mix LEVEL CH to MIX (not ALL)

To Mix Pan — CH to MIX (not ALL)

To Mix PRE/POST CH to MIX (not ALL)

To Matrix ON MIX TO MTRX, ALL

To Matrix LEVEL MIX TO MTRX, ALL

To Matrix POINT MIX TO MTRX, ALL

To Matrix PAN — MIX ALL

To Stereo On MIX ALL

To Stereo Point MIX ALL

Post To ST MIX ALL

Mute Assign MIX ALL

DCA Assign MIX ALL

PAIR MIX ALL

VARI/FIX MIX ALL

Global Paste —

Solo Safe —

Cue —

Mute Safe —

Selective Recall —

Tracking Recall —

Parameter Pair Recall Safe

Recall Safe —

Fade Time MATRIX FADER, ALL

Insert MATRIX ALL

On MATRIX ALL

Fader MATRIX FADER, ALL

BALANCE — MATRIX ALL

Comp MATRIX COMP, ALL

EQ MATRIX EQ, ALL

Delay On MATRIX DELAY, ALL

Delay TIME GANG MATRIX DELAY, ALL

Mute Assign MATRIX ALL

DCA Assign MATRIX ALL

PAIR MATRIX ALL

Global Paste —

Solo Safe —

Cue —

Mute Safe —

Selective Recall —

Tracking Recall —

Parameter

Pair Recall Safe

Recall Safe —

Fade Time ST FADER, ALL

Insert ST ALL

On ST ALL

Fader SY FADER, ALL

BALANCE — ST ALL

Comp ST COMP, ALL

EQ ST EQ ALL

Delay On ST DELAY, ALL

Delay TIME GANG ST DELAY, ALL

Mute Assign ST ALL

DCA Assign ST ALL

MONO — ST ALL

To Matrix On ST TO MTRX, ALL

To Matrix LEVEL ST TO MTRX, ALL

To Matrix POINT ST TO MTRX, ALL

To Matrix PAN — ST ALL

Global Paste —

Solo Safe —

Cue —

Mute Safe —

Selective Recall —

Tracking Recall —

Parameter Pair Recall Safe

INPUT PATCH Turn off the library link.*

OUTPUT PATCH

Tu rn off the library link.*

EFF1-8

GEQ1-12 LINK GEQ1-12

DCA

FADER,MUTE

DCA1-8

DCA FADE TIME

DCA1-8

DCA NAME

DCA1-8 (WITH NAME)

MUTE MASTER

MIDI REMOTE

MIDI REMOTE A-D

PLUG-IN

PLUG-IN 1-4

Yamaha V1 Manuale utente

Marca: Yamaha

Modello: V1

Categoria: Attrezzatura musicale

Tipo: Manuale utente

Questo manuale è adatto anche per

Scarica il pdf

rapporto

in altre lingue

English: Yamaha V1 User manual
français: Yamaha V1 Manuel utilisateur
español: Yamaha V1 Manual de usuario
Deutsch: Yamaha V1 Benutzerhandbuch
русский: Yamaha V1 Руководство пользователя
Nederlands: Yamaha V1 Handleiding
português: Yamaha V1 Manual do usuário
dansk: Yamaha V1 Brugermanual
čeština: Yamaha V1 Uživatelský manuál
polski: Yamaha V1 Instrukcja obsługi
svenska: Yamaha V1 Användarmanual
Türkçe: Yamaha V1 Kullanım kılavuzu
suomi: Yamaha V1 Ohjekirja
română: Yamaha V1 Manual de utilizare

Documenti correlati

Altri documenti

Tascam DP-03 Manuale del proprietario