Yamaha DSP5D Manuale del proprietario

PM5DV2/DSP5D Editor Owner’s Manual

1

❏

Special Notices

•The software and this owner’s manual are the exclusive copyrights of Yamaha Corporation.

•Copying of the software or reproduction of this manual in whole or in part by any means is expressly forbidden without the

written consent of the manufacturer.

•Copying of the commercially available music sequence data and/or digital audio ﬁles is strictly prohibited except for your per-

sonal use.

•Yamaha makes no representations or warranties with regard to the use of the software and documentation and cannot be held

responsible for the results of the use of this manual and the software.

•The screen displays as illustrated in this owner’s manual are for instructional purposes, and may appear somewhat different

from the screens which appear on your computer.

•Future upgrades of application and system software and any changes in speciﬁcations and functions will be announced separately.

•Windows is a registered trademark of Microsoft Corporation in the U.S. and other countries.

•Apple, Mac and Macintosh are trademarks of Apple Inc., registered in the U.S. and other countries.

•The company names and product names in this Owner’s Manual are the trademarks or registered trademarks of their respec-

tive companies.

Yamaha Pro Audio Global Site

http://www.yamahaproaudio.com/

Contents

Getting Started .................................................. 2

INPUT CH window ............................................. 8

ST IN window................................................... 11

FX RTN window................................................ 13

MIX window..................................................... 15

MATRIX window .............................................. 17

STEREO window ............................................... 19

DCA window .................................................... 21

Selected Channel window ............................... 22

If an input channel is selected ....................... 22

If a MIX channel is selected ........................... 31

If a MATRIX channel is selected..................... 36

If a STEREO A/B channel is selected............... 37

Patch Editor window........................................ 40

Surround Editor window.................................. 45

GEQ window .................................................... 47

Effect Editor window........................................ 50

DCA/Mute Group window............................... 54

Scene window .................................................. 57

Library window ................................................ 66

Meter window.................................................. 68

Timecode Counter window.............................. 69

Sync window .................................................... 69

Preference window .......................................... 70

User Defined Keys Setup window.................... 72

Fader Mode Assign window............................. 73

Output Port Att window .................................. 73

Word Clock window......................................... 74

Oscillator window ............................................ 77

Cue/Solo window............................................. 79

Port Trim window ............................................ 82

Keyboard Shortcuts.......................................... 83

Index................................................................. 84

*Speciﬁcations and descriptions in this owner ’s manual are

for information purposes only. Yamaha Corp. reserves the

right to change or modify products or speciﬁcations at any

time without prior notice. Since speciﬁcations, equipment

or options may not be the same in every locale, please

check with your Yamaha dealer.

PM5DV2/DSP5D Editor

Owner’s Manual

Term Deﬁnition

Studio Manager refers to Studio Manager V2

PM5D Editor

refers to PM5DV2 Editor

This editor works with PM5DV2. Make sure that the console’s ﬁrmware has been updated to V2.

Description of menus and buttons

In the event that menu and button names on a Windows system are different from those on a Mac, this manual uses the

Windows menu and button names followed by the Mac menu and button names in parentheses.

PM5DV2/DSP5D Editor Owner’s Manual

2

What is PM5D/DSP5D Editor?

PM5D Editor and DSP5D Editor allow you to remotely control the parameters of the PM5D or DSP5D, and save the

parameters on your computer.

PM5D/DSP5 Editor are used by starting them up from within Studio Manager. To use PM5D/DSP5D Editor, you

must perform the following steps.

“Start up Studio Manager and make settings”

→

“Start up PM5D Editor or DSP5D Editor and make settings”

→

“Synchronize with the PM5D/DSP5D itself (

➥

p.5)”

For details on operations in Studio Manager, refer to the Studio Manager operating manual.

Settings in PM5D/DSP5D Editor

You will need to set the following items individually for each editor that is open.

• Before you make the following settings, you must select the MIDI ports in the Setup window of Studio

Manager.

•To start up PM5D Editor or DSP5D Editor in the Setup window of Studio Manager, double-click the cor-

responding icon in the Studio Manager window.

❏

PM5D Editor: System Setup

To open the System Setup window, choose the [File] menu item [System Setup].

You must specify the Input port and the Output port.

Input port/Output port:

From the ports you have previ-

ously speciﬁed in Studio Manager, select the ports you will use

for communication with the PM5D.

Console Device ID:

PM5D Editor can control the desired

single unit chosen from a maximum of eight units that each

have their own ID. Select the ID of the unit you want to control.

Fast Sync:

This shortens the synchronization time with the

PM5D itself. If synchronization fails, clear this check box.

Level Meter:

This speciﬁes whether level meter data will be

included in the communication with the PM5D itself. If this

check box is selected, level meter data from the PM5D will be

received, but the response speed may be slower. If you feel that

the response is slow, clear this check box.

System Color:

You can change the workspace color of

PM5D Editor. Choose one of eight colors from the pulldown

menu. This is convenient when you need to distinguish

between multiple instances of PM5D Editor.

Synchronize Plug-in Boards:

If these option boxes are selected, the data of the Y96K plug-in board

installed in the corresponding slot will be synchronized along with the scene data.

Window Control from Console:

PM5D Editor windows can be opened or closed remotely from the

PM5D itself by using user-deﬁned keys. This option enables remote control.

Set Default:

By clicking this button, you can store the current System Setup settings as the default values for

PM5D Editor.

Getting Started

NOTE

PM5DV2/DSP5D Editor Owner’s Manual

3

❏

DSP5D Editor: System Setup

To open the System Setup window, choose [System Setup] from the [File] menu.

You must specify the Input port and Output port.

Input port/Output port:

From the ports you have previ-

ously speciﬁed in Studio Manager, select the ports you will use

for communication with the DSP5D.

Fast Sync:

This shortens the time required for synchroniza-

tion with the DSP5D. If synchronization fails, you should dis-

able (clear) this item.

Level Meter:

This speciﬁes whether level meter data will be

included in the communication with the DSP5D. If this check

box is selected, level meter data from the DSP5D will be

received, but the response speed may be slower. If you feel that

the response is slow, clear this check box.

System Color:

You can change the workspace color of

DSP5D Editor. Choose one of eight colors from the pulldown

menu. This is convenient when you need to distinguish

between multiple instances of DSP5D Editor.

Set Default:

By clicking this button, you can store the cur-

rent System Setup settings as the default values for DSP5D Editor.

❏

Mixer Setup

To open the Mixer Setup window, choose [Mixer Setup] from the [File] menu.

Pair Mode:

Select whether faders will be paired Horizontally or Vertically.

Pan Nominal Position:

Select whether the signal will be at nominal level when panned to the center (Cen-

ter) or when panned all the way to left or right (L<-->R). You can make separate settings for monaural channels

and paired channels.

Bus Setup:

Select the MIX bus mode (VARI/FIXED) for every two adjacent odd-numbered/even-numbered

MIX buses. MIX buses assigned as surround buses are indicated as “SURROUND” and cannot be changed.

Surround Bus Allocation:

Select the MIX buses (MIX 1–8 or MIX 9–16) that will be used as surround

buses.

Stereo B Setup:

Specify whether the same signal as the STEREO A bus will be sent to the STEREO B bus (Ste-

reo Bus), or whether the STEREO B bus will function as the CENTER bus for LCR mode (Center Bus).

PM5DV2/DSP5D Editor Owner’s Manual

4

Number of Effects:

This changes the number of assigned internal effects and GEQ modules. Decreasing the

number of internal effects by one will increase the number of available GEQ modules by one. You can change the

number assigned between eight internal effects (and twelve GEQ modules) to no internal effects (and twenty

GEQ modules). You can use up to eight GEQ modules as effects.

+48V Master:

This function is found only in DSP5D Editor. It is the master switch for the phantom power

(+48V) supplied to INPUT jacks 1–48 and ST IN jacks 1–4. If this switch is off, phantom power will not be

applied, regardless of whether the +48V shown in the display is on or off.

Surround Mode:

Select the surround mode (STEREO, 3-1, 5.1, 6.1).

External HA:

This speciﬁes the connection ports for external HA (AD8HR) units connected via the slots.

External HA units are assigned an ID of 1–8 (1–4 on the DSP5D), and here you can select the ports to which each

will be connected.

IP Address:

This function is found only in DSP5D Editor. You can specify the IP Address, Subnet Mask, and

Default Gateway values. If the DSP5D and computer are connected in a one-to-one correspondence, we recom-

mend that you use the following default values.

•

IP Address

................... 192.168.0.129

•

Subnet Mask

............... 255.255.255.0

•

Default Gateway

......... 192.168.0.1

•For details on network settings for your computer, refer to DME-N Network Driver installation guide for

DSP5D(Windows) or Network-MIDI Driver installation guide(Mac).

• If you changed the IP Address, you must close DSP5D Editor and Studio Manager, and re-specify the

IP Address values for the DME-N Network Driver communication port or the Network-MIDI Driver com-

munication port. The connection between the DSP5D and DSP5D Editor will be broken when you

change the IP Address

Cascade Connection:

This function is found only in DSP5D Editor. It speciﬁes the Cascade Machine ID

when using a cascade connection. If this is set to 1, you will be able to make DME Connection settings. If this is

set to 2 or 3, the Cascade setting will be Slave, and you won’t be able to make DME Connection settings.

DME Connection:

This function is found only in DSP5D Editor. This is a setting for connecting the DSP5D

with a DME series unit (except the DME32). For details on the connection method, refer to the Global function

MIDI Remote Function section in the reference section of the DSP5D manual.

Even if you enable DME Connection, remote control of the DME cannot be performed from DSP5D Editor.

Use the separate DME Designer to remotely control the DME.

• Input Port / Output Port

This speciﬁes the DSP5D’s connector/slot to which the DME is connected. You can choose SLOT1, SLOT2,

CASCADE IN/OUT D-SUB, or CASCADE OUT RJ-45.

• If you select CASCADE IN/OUT D-SUB or CASCADE OUT RJ-45, the Slot display area of Patch Editor

will show the selected connector/slot.

• Since CASCADE IN RJ-45 cannot be used, you must connect the DSP5D via its CASCADE OUT RJ-

45 connector if you use an Ethernet cable to connect the DME and DSP5D.

• Monitor Port

This speciﬁes the DSP5D port that will receive monitor signals from the DME. You can select stereo channels

from within the port selected by Input Port.

• Connect

This initiates or ends communication between the DSP5D and DME. Communication will begin if this check

box is selected, and will end if this check box is cleared. The actual start or end of communication will occur

when you click the OK button.

• MIDI Program Change

This allows the DME to recall a scene according to the Program Change Table assignment in synchronization

with scene recall that occurs on the DSP5D. If you enable this function by selecting the check box, synchroni-

zation via MIDI program change will be enabled. In order to enable this function, the Connect check box

must be selected.

NOTE

PM5DV2/DSP5D Editor Owner’s Manual

5

Synchronizing PM5D/DSP5D Editor

When PM5D/DSP5D Editor starts up, the parameter settings on the PM5D/DSP5D itself and the parameter settings

in PM5D/DSP5D Editor may be different. Therefore, you must ﬁrst match the parameter settings on the PM5D/

DSP5D itself with those in PM5D/DSP5D Editor. This operation is called “synchronization.” Follow the steps below

to synchronize PM5D/DSP5D Editor.

1 Select [Synchronize], then [Re-synchronize].

The window shown at right opens.

2 Select whether you want to transfer your settings to PM5D/

DSP5D Editor, or vice versa.

At this time, the All Libs option determines whether or not Scene and

Library data is synchronized.

If the [Fast Sync] check box is selected, synchronization with the unit itself will be faster. In order to enable this

item, you must select the [Fast Sync] check box in the System Setup window.

PC -> Console (DSP5D):

Tr ansfers the current parameter settings in PM5D/DSP5D Editor to the PM5D/

DSP5D itself.

Console (DSP5D) -> PC:

Tr ansfers the current parameter settings of the PM5D/DSP5D itself to the PM5D/

DSP5D Editor.

3 Click [OK].

Do not operate the PM5D/DSP5D itself while synchronization is in progress.

• When you synchronize with Studio Manager, synchronize will occur between all editors selected in Stu-

dio Manager and the respective hardware units.

• If loading of scene data from an external location is disabled on the unit itself, the Direction will be set to

Console (DSP5D) -> PC. If there is scene data that is set to Read Only, a dialog box will appear when

you click OK, asking whether you want the read-only data to be synchronized as Console (DSP5D) ->

PC, or not synchronized. Your selection will apply to all scene data that is set to Read Only.

Ofﬂine Edit Function

If you do not want to synchronize PM5D/DSP5D itself with PM5D/DSP5D Editor, select [Ofﬂine Edit] from the

[Synchronization] menu. To apply your off-line edits to the PM5D/DSP5D itself, select [Re-Synchronize] from the

[Synchronization] with the PC -> Console (DSP5D) option to synchronize the PM5D/DSP5D itself with PM5D/

DSP5D Editor.

The Ofﬂine Edit function is also activated when you click the [ONLINE]/[OFFLINE] button in the Sync window.

Some effect parameters in the PM5D/DSP5D itself change their displayed values depending on the sam-

pling frequency. If you switch PM5D/DSP5D Editor from OFFLINE to ONLINE, displayed parameter val-

ues may change because PM5D/DSP5D Editor loads the sampling frequency from the PM5D/DSP5D

itself and updates the display.

Working with Sessions

In PM5D/DSP5 Editor, mix settings for an entire PM5D/DSP5D unit, including scene and library data, are called a

Session.

When you save a session in the window of an editor, the settings of only that editor will be saved in a ﬁle. Session ﬁles

saved by PM5D/DSP5D Editor have a ﬁlename extension of “.YSE”. Files in which only the PM5D itself data is saved

(ﬁlename extension “.PM5”) can also be handled, allowing you to use a memory card to exchange data with the

PM5D itself.

Creating a new Session

Choose [New Session] from the [File] menu.

Opening a previously saved Session

Choose [Open Session] from the [File] menu.

Saving the current Session

Choose [Save Session] from the [File] menu.

Saving the current Session with a new name

Choose [Save Session As...] from the [File] menu.

NOTE

PM5DV2/DSP5D Editor Owner’s Manual

6

If you save a Session in the Studio Manager window, all selected Editor settings are saved in a ﬁle with a ﬁle extension

of “.YSM.”

Data with the extension “.PM5” that was saved by PM5D version 1 and PM5D Editor (supporting version

1) can also be opened by PM5DV2 Editor.

Window operations

You can select and open each window from the [Win-

dows] menu. For the INPUT CH window and Effect Edi-

tor window, use the sub-menu to select the channels or

library you want to see.

In the Library window or Scene window, click the tabs

located at the top of the window to switch between

pages.

Edit functions

❏

Ch Copy / Ch Paste (channel copy / channel paste) function

The Ch Copy/Ch Paste function copies or pastes the channel that is selected by the [SELECT] button (or [SEL] key.)

Copy can also be executed by using the keyboard’s <Ctrl> ( ) key + <C> key. Paste can also be executed by using the

keyboard’s <Ctrl> ( ) key + <V> key.

Since the Undo data is cleared when you execute Ch Paste, Undo will become unavailable at that point.

❏

Ch Move (channel move) function

The Ch Move function moves the speciﬁed channel to the location of

another channel that has the same structure.

When you select Ch Move, the dialog box shown at the right will appear.

When you click the buttons located below Source and Destination, a chan-

nel list will appear.

Select the move Source and move Destination, and click the OK button to

move the channel.

The channels affected by Ch Move will be the same set of channels as selected by [SELECT] button (or [SEL] key).

This is not available for output channels. Undo data will be cleared when you execute Ch Move, so all Undo opera-

tions will become unavailabl at that point.

• If the Source is a paired channel, the channels will be moved as a pair.

• If there are paired channels between the Source and Destination, movement occurs in pairs (units of

two channels).

•Movement will occur in pairs (units of two channels) if parameters of which there is one instance for

every two channels are turned on (also if parameters such as GANG or LINK are on).

NOTE

PM5DV2/DSP5D Editor Owner’s Manual

7

Undo/Redo Function

In PM5D/DSP5D Editor, you can cancel the latest operation (Undo) and also cancel the cancellation of the latest

operation (Redo). If you perform an Undo operation twice in a row, you can cancel the two most-recent operations.

If you perform an Undo operation three times in a row, you can cancel the three most-recent operations. In this way,

you can cancel multiple recent operations.

The following table describes how to use the Undo/Redo function.

Please note, however, that after you perform one of the following operations, you cannot successfully undo or redo

any previous operation:

•Operations on the PM5D/DSP5D itself

• Quitting Studio Manager

•Changing the surround mode or pair mode

•Synchronizing with the PM5D/DSP5D itself

•Session operations

•The GEQ [EQ FLAT] button

•Moving the fader positions by changing the GEQ variable width

You cannot Undo or Redo the following operations:

• Edits in the Setup window

• Synchronization

• Opening and closing the windows

• Resizing the windows

• Ch Copy/Ch Paste

• Ch Move

For some functions, there are also other operations that cannot be undone.

For Library and Scene operations, Undo/Redo will apply only to the single preceding operation. You can-

not undo an operation that occurred two or more operations previously. Undo/Redo in these windows can

be performed only using the [UNDO] button in the respective window. Even if you execute a scene recall

from the Sync window, you cannot use a shortcut or menu operation to undo this.

Other Functions

❏

Resetting to the default value (Ctrl ( ) + click)

Move the cursor to a control or a parameter value, then hold down the <Ctrl> ( ) key and click the mouse but-

ton to reset the value to the default (e.g., to reset an Input Channel fader to –

∞

dB, or reset a pan setting to Cen-

ter).

❏

Ctrl ( ) +Shift+Click

Move the cursor to a fader or AUX Send control, then hold down the <Ctrl> ( ) key and <Shift> key and click

the mouse button to reset the value to the nominal level.

Undo

Choose [Undo] from the [Edit] menu.

Redo

Choose [Redo] from the [Edit] menu.

NOTE

PM5DV2/DSP5D Editor Owner’s Manual

8

This window displays the parameters of input channels 1–24 or 25–48. The window shows either the channel 1–24

layer or the channel 25–48 layer. To open the other layer’s window, choose the [Windows] menu command [INPUT

CH] and choose “CH1-24” or “CH25-48.”

You can use the [View] menu to choose the parameters that will be displayed in the window.

A Input patch

Here you can select an input source to assign to the input channel, from the following

choices.

*These choices are shown only in PM5D Editor.

B +48V

Switches on/off the phantom power (+48V) of the internal HA (PM5D-RH model and

DSP5D only) or of the external HA (AD8HR, AD824) patched to the input channel.

C HA GAIN

Drag the knob in the screen to adjust the gain of the internal HA (PM5D-RH model

and DSP5D only) or of the external HA (AD8HR, AD824) patched to the input chan-

nel.

NONE No assignment

AD1–AD48 INPUT jacks 1–48

AD1L–AD4R L/R channels of ST IN jacks 1–4

S1-1, S1-2...S4-15, S4-16

Input channels of an I/O card installed in slots 1–4

On the DSP5D, SLOT3 and SLOT4 are assigned

to CASCADE IN/OUT D-SUB.

FX1L, FX1R...FX8L, FX8R L/R outputs of internal effects 1–8

2TR D1L, 2TR D1R...2TR D3L, 2TR D3R L/R channels of 2TR IN DIGITAL jacks 1–3*

2TR A1L, 2TR A1R, 2TR A2L, 2TR A2R L/R channels of 2TR IN ANALOG jacks 1/2*

INPUT CH window

1

2

3

PM5DV2/DSP5D Editor Owner’s Manual

9

D HPF (High Pass Filter)

Switches the high pass ﬁlter on/off. You can drag the numeric value up or down to edit

the cutoff frequency.

E Ø (Phase)

Inverts the phase of the signal after AD conversion.

F INSERT

Switches the INSERT PATCH path between enabled/disabled.

G DIRECT

Switches the output to the DIRECT OUT PATCH port between enabled/disabled.

H GATE

Turns the gate on/off. The indica-

tor immediately below the button

shows the gate’s on/off setting

and the open/closed status.

I COMP (Compressor)

Switches the compressor on/off. When the compressor is on, the GR meter immediately

below the button shows the amount of gain reduction.

J EQ (Equalizer)

Switches the EQ on/off. The graph immediately below the button shows the approxi-

mate response of the EQ. You can drag within the graph to edit the response of the EQ.

To reset the EQ to ﬂat response, hold down the <Ctrl> key ( key) of your computer

keyboard and click the graph.

K DELAY

Switches the delay on/off. You can also edit the delay time by dragging the numeric

value located immediately below the button up or down

L Channel number

Indicates the input channel number corresponding to this module. You can double-

click this number to open the Selected Channel window for this channel. If you hold

down your computer keyboard’s <Ctrl> key ( key) and double-click this, the Locked

window will open.

M MIX SEND

The bar graphs in this area indicate the send levels of

the signals sent from the input channel to MIX buses.

You can also adjust the send levels by dragging a bar

graph to left or right.

The bar graph display will change according to the

send position (pre/post) and on/off status of the signal

sent from the input channel to the MIX buses.

•You can turn this on/off by clicking the number at the left.

•For FIXED-type MIX buses, the bar graph is ﬁxed at nominal level (0 dB),

and only the on/off status is shown.

N PAN

Sets the panning of the signal sent from the input channel to the STEREO bus. This

may be BALANCE depending on the PAN mode.

O SELECT

Selects input channel for which you want to perform operations. This is linked with the

INPUT channel strip [SEL] keys on the PM5D panel.

P CH ON (Channel on) button

Switches the input channel on/off. This is linked with the INPUT channel strip CH

[ON] keys on the PM5D panel.

L

O

P

N

M

5

6

7

8

9

J

4

K

Gate= closed

(red)

Gate= open

(green)

Gate= off

Pre/on (green)

Pre/off (green)

Post/off (yellow)

Post/on (yellow)

NOTE

PM5DV2/DSP5D Editor Owner’s Manual

10

Q Channel name

This is a text box that displays the channel name. You can also edit the channel name in

this text box.

Note that while the channel number (

L) does not change when you switch pairing

mode in the Mixer Setup window, the channel name display will change according to

the pairing mode.

For example if the CH1-24 layer is displayed, and you switch the pairing mode from

Horizontal to Vertical, the channel name indications that had been arranged in the

order of channels 1, 2, 3 ... 24, 25 will change to the order of 1, 3, 5 ... 45, 47.

R Fader

Adjusts the input level of the input channel. This is linked with the INPUT channel

strip faders on the PM5D panel.

The current fader value is shown in the numeric box immediately below the fader. The

level meter at the right of the fader shows the level of the input signal.

The numbers and

alphabetical letters at

the right of the fader

indicate the DCA

group and mute

groups to which that

channel belongs, and

show the Recall Safe

and Mute Safe status of

the channel.

S CUE

This button cue-monitors the signal of the input channel. This is linked with the

INPUT channel strip [CUE] keys on the PM5D panel. If SOLO is active, this will func-

tion as SOLO.

Q

S

R

The numbers of DCA groups to which this

channel belongs are shown in yellow.

The numbers of mute groups to which this

channel belongs are shown in red.

If this channel is set to Recall Safe, the R

character is shown in orange.

If this channel is set to Mute Safe, the M char-

acter is shown in red.

PM5DV2/DSP5D Editor Owner’s Manual

11

In this window you can view and edit the parameters of ST IN channels 1–4. You can use the [View] menu to choose

the parameters that will be displayed in the window.

A Input patch

Selects the input source that will be assigned to the ST IN channel. The input sources

that can be assigned are the same as for an input channel (➥ p.8).

B +48V

Switches on/off the phantom power (+48V) of the internal HA (PM5D-RH model and

DSP5D only) or of the external HA (AD824, AD8HR) patched to the ST IN channel.

C HA GAIN

Drag the knob in the screen to adjust the gain of the internal HA (PM5D-RH model

and DSP5D only) or of the external HA (AD824, AD8HR) patched to the ST IN chan-

nel.

D HPF (High Pass Filter)

Switches the high pass ﬁlter on/off. You can drag the numeric value up or down to edit

the cutoff frequency.

E Ø (Phase)

Inverts the phase of the signal after AD conversion.

F INSERT

Switches the INSERT PATCH path between enabled/disabled.

G DIRECT

Switches the output to the DIRECT OUT PATCH port between enabled/disabled.

ST IN window

5

6

7

1

2

3

4

PM5DV2/DSP5D Editor Owner’s Manual

12

H GATE

Turns the gate on/off. The indicator immediately below the button shows the gate’s on/

off setting and the open/closed status (➥ p.9).

I COMP (Compressor)

Switches the compressor on/off. When the compressor is on, the GR meter immediately

below the button shows the amount of gain reduction.

J EQ (Equalizer)

Switches the EQ on/off. The graph immediately below the button shows the approxi-

mate response of the EQ. You can drag the graph to edit the response of the EQ, or hold

down the <Ctrl> key ( key) of your computer keyboard and click the graph to reset

it to a ﬂat response.

K DELAY

Switches the delay on/off. You can also edit the delay time by dragging the numeric

value located immediately below the button up or down

L Channel number

This is the number of the ST IN channel for this module. You can double-click this

number to open the Selected Channel window for this channel. If you hold down your

computer keyboard’s <Ctrl> key ( key) and double-click this, the Locked window

will open.

M MIX SEND

The send levels of the signals sent from the ST IN channel to the MIX buses are shown

as bar graphs. You can also adjust the send levels by dragging a bar graph to left or right.

The bar graph display will change according to the send position (pre/post) and on/off

status of the signal sent from the ST IN channel to the MIX buses (➥ p.9).

N PAN

Speciﬁes the panning of the signal sent from the ST IN channel to the STEREO bus.

(You can set L and R separately.) This may be BALANCE depending on the PAN mode.

O SELECT

Selects the ST IN channel for which you want to perform operations. (L and R can be

selected separately.) This is linked with the ST IN channel strip [SEL] keys on the

PM5D panel.

P CH ON (Channel on) button

Switches the ST IN channel on/off. This is linked with the ST IN channel strip CH

[ON] keys on the PM5D panel.

Q Channel name

This is a text box that displays the channel name. You can also edit the channel name in

this text box.

R Fader

Adjusts the input level of the ST IN channel. This is linked with the faders of the ST IN

channel strip on the PM5D panel.

The numbers and alphabetical letters at the right of the fader indicate the DCA group

and mute groups to which that channel belongs, and show the Recall Safe and Mute

Safe status of the channel (➥ p.10).

S CUE

This button cue-monitors the signal of the ST IN channel. This is linked with the ST IN

channel strip [CUE] keys on the PM5D panel. If SOLO is active, this will function as

SOLO.

O

Q

N

P

R

S

L

M

8

J

9

K

PM5DV2/DSP5D Editor Owner’s Manual

13

In this window you can view and edit the parameters of FX RTN channels 1–4. You can use the [View] menu to

choose the parameters that will be displayed in the window.

A Input patch

Selects the input source that will be assigned to the FX RTN channel. The input sources

that can be assigned are the same as for an input channel (➥ p.8).

B +48V

Switches on/off the phantom power (+48V) of the internal HA (PM5D-RH model and

DSP5D only) or of the external HA (AD8HR, AD824) patched to the FX RTN channel.

C HA GAIN

Drag the knob in the screen to adjust the gain of the internal HA (PM5D-RH model

and DSP5D only) or of the external HA (AD8HR, AD824) patched to the FX RTN

channel.

D HPF (High Pass Filter)

Switches the high pass ﬁlter on/off. You can drag the numeric value up or down to edit

the cutoff frequency.

E Ø (Phase)

Inverts the phase of the signal after AD conversion.

F EQ (Equalizer)

Switches the EQ on/off. The graph immediately below the button shows the approxi-

mate response of the EQ. You can drag the graph to edit the response of the EQ, or hold

down the <Ctrl> key ( key) of your computer keyboard and click the graph to reset

it to a ﬂat response.

FX RTN window

6

1

2

5

3

4

PM5DV2/DSP5D Editor Owner’s Manual

14

G Channel number

This is the number of the FX RTN channel for this module. You can double-click this

number to open the Selected Channel window for this channel. If you hold down your

computer keyboard’s <Ctrl> key ( key) and double-click this, the Locked window

will open.

H MIX SEND

The send levels of the signals sent from the FX RTN channel to the VARI-type MIX

buses are shown as bar graphs (the L/R settings are linked). You can also adjust the send

levels by dragging a bar graph to left or right.

The bar graph display will change according to the send position (pre/post) and on/off

status of the signal sent from the FX RTN channel to the MIX buses (➥ p.9).

I PAN

Speciﬁes the panning of the signal sent from the FX RTN channel to the STEREO bus.

(You can set L and R separately.) This may be BALANCE depending on the PAN mode.

J SELECT

Selects the FX RTN channel for which you want to perform operations. (L and R can be

selected separately.) This is linked with the FX RTN channel strip [SEL] keys on the

PM5D panel.

K CH ON (Channel on) button

Switches the FX RTN channel on/off. This is linked with the FX RTN channel strip CH

[ON] keys on the PM5D panel.

L Channel name

This is a text box that displays the channel name. You can also edit the channel name in

this text box.

M Fader

Adjusts the input level of the FX RTN channel. This is linked with the faders of the FX

RTN channel strip on the PM5D panel.

The numbers and alphabetical letters at the right of the fader indicate the DCA group

and mute groups to which that channel belongs, and show the Recall Safe and Mute

Safe status of the channel (➥ p.10).

N CUE

This button cue-monitors the signal of the FX RTN channel. This is linked with the FX

RTN channel strip [CUE] keys on the PM5D panel. If SOLO is active, this will function

as SOLO.

K

M

N

7

J

9

L

8

PM5DV2/DSP5D Editor Owner’s Manual

15

In this window you can view and edit the parameters of MIX channels 1–24. You can use the [View] menu to choose

the parameters that will be displayed in the window.

A EQ (Equalizer)

Switches the EQ on/off. The graph immediately below the button shows the approxi-

mate response of the EQ. You can drag the graph to edit the response of the EQ, or hold

down the <Ctrl> key ( key) of your computer keyboard and click the graph to reset

it to a ﬂat response.

B COMP (Compressor)

Switches the compressor on/off. When the compressor is on, the GR meter immediately

below the button shows the amount of gain reduction.

C INSERT

Switches the INSERT PATCH path between enabled/disabled.

D DELAY

Switches the delay on/off. You can also edit the delay time by dragging the numeric

value located immediately below the button up or down

E Channel number

Indicates the number of the MIX channel corresponding to this module. You can dou-

ble-click this number to open the Selected Channel window for this channel. If you

hold down your computer keyboard’s <Ctrl> key ( key) and double-click this, the

Locked window will open.

MIX window

5

4

1

3

2

PM5DV2/DSP5D Editor Owner’s Manual

16

F MTRX (Send level to MATRIX buses)

These bar graphs indicate the send levels of the signals

sent from the MIX channel to each MATRIX bus. You

can also adjust the send levels by dragging a bar graph

to left or right.

The bar graph display will change as follows according

to the send position (pre/post) and on/off status of the

signal sent from the MIX channel to the MATRIX

buses.

You can turn this on/off by clicking the number at left.

G TO ST (To STEREO)

This is an on/off switch for the signal sent from the MIX channel to the STEREO bus.

H PAN

Sets the panning of the signal sent from the MIX channel to the STEREO bus.

I VARI/FIXED

Indicates the type (VARI or FIXED) of the currently selected MIX bus. (This parameter

is for display only. If you want to switch between VARI/FIXED from within PM5D/

DSP5D Editor, use the Mixer Setup window (➥ p.3)

If surround mode is enabled, MIX buses that are assigned as surround buses are dis-

played with the name of the surround channel (L, R, Ls, Rs ...), and the other MIX

buses are displayed as “FIXED.”

J SELECT

Selects the MIX channel for which you want to make settings. This is linked with the

MIX [SEL] keys in the MIX section of the PM5D panel.

K ON

Switches the MIX channel on/off.

L Channel name

This is a text box that indicates the channel name. You can also edit the channel name

within this text box.

M Fader

Adjusts the output level of the MIX channel. The current fader value is shown in the

numeric box immediately below the fader. The level meter at the right of the fader

shows the output level of the signal.

The numbers and alphabetical letters at the right of the fader indicate the DCA group

and mute groups to which that channel belongs, and show the Recall Safe and Mute

Safe status of the channel. (For the signiﬁcance of the numbers and alphabetical letters,

see ➥ p.10).

N CUE

This button cue-monitors the signal of the MIX channel. This is linked with the MIX

[CUE] keys in the MIX section of the PM5D panel. If SOLO is active, this will function

as SOLO.

7

8

9

N

M

J

K

L

6

Pre/on (green)

Pre/off (green)

Post/off (yellow)

Post/on (yellow)

NOTE

PM5DV2/DSP5D Editor Owner’s Manual

17

In this window you can view and edit the parameters of MATRIX channels 1–8. You can use the [View] menu to

choose the parameters that will be displayed in the window.

MATRIX window

PM5DV2/DSP5D Editor Owner’s Manual

18

A MIX (Send levels from the MIX channels to the MATRIX bus)

Here you can view and edit the send levels of the signals sent from each MIX channel to

the MATRIX bus. The method of operation and the meaning of the display are the same

as for (

6) MTRX in the MIX window (➥ p.16).

B STEREO (Send levels from the STEREO channels to the MATRIX

bus)

Here you can view and edit the send levels of the signals sent from the STEREO A/B

channels to the MATRIX bus. The method of operation and the meaning of the display

are the same as for (

6) MTRX in the MIX window (➥ p.16).

C Channel number

Indicates the number of the MATRIX channel corresponding to this module. You can

double-click this number to open the Selected Channel window for this channel. If you

hold down your computer keyboard’s <Ctrl> key ( key) and double-click this, the

Locked window will open.

D EQ (Equalizer)

Switches the EQ on/off. The graph immediately below the button shows the approxi-

mate response of the EQ. You can drag the graph to edit the response of the EQ, or hold

down the <Ctrl> key ( key) of your computer keyboard and click the graph to reset

it to a ﬂat response.

E COMP (Compressor)

Switches the compressor on/off. When the compressor is on, the GR meter immediately

below the button shows the amount of gain reduction.

F INSERT

Switches the INSERT PATCH path between enabled/disabled.

G DELAY

Switches the delay on/off. You can also edit the delay time by dragging the numeric

value located immediately below the button up or down

H SELECT

Selects the MATRIX channel for which you want to make settings. This is linked with

the MATRIX [SEL] keys in the MATRIX section of the PM5D panel.

I ON

This switches the MATRIX channel on/off. This is linked with the MATRIX [ON] keys

in the MATRIX section of the PM5D panel.

J Channel name

This is a text box that indicates the channel name. You can also edit the channel name

within this text box.

K Fader

This adjusts the output level of the MATRIX channel. The current fader value is shown

in the numeric box immediately below the fader. The level meter at the right of the

fader shows the output level of the signal.

The numbers and alphabetical letters at the right of the fader indicate the DCA group

and mute groups to which that channel belongs, and show the Recall Safe and Mute

Safe status of the channel. (For the signiﬁcance of the numbers and alphabetical letters,

see ➥ p.10).

L CUE

This button cue-monitors the signal of the MATRIX channel. This is linked with the

MATRIX [CUE] keys in the MATRIX section of the PM5D panel. If SOLO is active, this

will function as SOLO.

4

6

7

8

9

J

K

L

3

1

2

5

PM5DV2/DSP5D Editor Owner’s Manual

19

In this window you can view and edit the parameters of the STEREO A/B channels. You can use the [View] menu to

choose the parameters that will be displayed in the window.

STEREO window

PM5DV2/DSP5D Editor Owner’s Manual

20

A EQ (Equalizer)

Switches the EQ on/off. The graph immediately below the button shows the approxi-

mate response of the EQ. You can drag the graph to edit the response of the EQ, or hold

down the <Ctrl> key ( key) of your computer keyboard and click the graph to reset

it to a ﬂat response.

B COMP (Compressor)

Switches the compressor on/off. When the compressor is on, the GR meter immediately

below the button shows the amount of gain reduction.

C INSERT

Switches the INSERT PATCH path between enabled/disabled.

D DELAY

Switches the delay on/off. You can also edit the delay time by dragging the numeric

value located immediately below the button up or down. If GANG is turned on, the L/R

delay time will be linked while maintaining their offset value. If GANG is off, the L/R

delay times can be edited individually.

E Channel number

This is the channel number (STEREO A or B) of this module. You can double-click this

number to open the Selected Channel window for this channel. If you hold down your

computer keyboard’s <Ctrl> key ( key) and double-click this, the Locked window

will open.

F MTRX (Send level to MATRIX buses)

Here you can view and edit the send levels of the signals sent from the STEREO A/B

channel to each MATRIX bus. The method of operation and the meaning of the display

are the same as for (

6) MTRX in the MIX window (➥ p.16).

G BALANCE

Adjusts the left/right balance of the STEREO A/B channel.

H SELECT

Selects the STEREO A/B channel for which you want to make settings. (You can specify

L and R independently.) This is linked with the STEREO [SEL] key in the STEREO A/B

channel strip of the PM5D panel.

I ON

This switches the STEREO A/B channel on/off. This is linked with the STEREO [ON]

key in the STEREO A/B channel strip of the PM5D panel.

J Channel name

This is a text box that indicates the channel name. You can also edit the channel name

within this text box.

K Fader

Adjusts the output level of the STEREO A/B channel. This is linked with the STEREO

fader in the STEREO A/B channel strip of the PM5D panel.

The current fader value is shown in the numeric box immediately below the fader. The

level meter at the right of the fader shows the output level of the signal.

The numbers and alphabetical letters at the right of the fader indicate the DCA group

and mute groups to which that channel belongs, and show the Recall Safe and Mute

Safe status of the channel. (For the signiﬁcance of the numbers and alphabetical letters,

see ➥ p.10).

L CUE

This button cue-monitors the signal of the STEREO A/B channel. This is linked with

the STEREO [CUE] key in the STEREO A/B channel strip of the PM5D panel. If SOLO

is active, this will function as SOLO.

K

L

9

7

8

J

1

3

4

5

6

2

La pagina sta caricando ...

Yamaha DSP5D Manuale del proprietario

Questo manuale è adatto anche per

Yamaha DSP5D Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti