Sony MEX-N6002BD Manuale del proprietario

MEX-N6002BD

4-687-334-23(1)

Bluetooth®

Audio System

Operating Instructions

GB

Bedienungsanleitung

DE

Mode d’emploi

FR

Istruzioni per l’uso

IT

Gebruiksaanwijzing

NL

To cancel the demonstration (DEMO) display, see page 18.

For the connection/installation, see page 30.

Zum Deaktivieren der Demo-Anzeige (DEMO) schlagen Sie

bitte auf Seite 20 nach.

Informationen zum Anschluss und zur Installation finden Sie auf

Seite 34.

Pour annuler la démonstration (DEMO), reportez-vous à la

page 20.

Pour le raccordement/l’installation, reportez-vous à la page 33.

Per annullare la dimostrazione (DEMO), vedere pagina 20.

Per l’installazione e i collegamenti, consultare pagina 33.

Om de demonstratie (DEMO) te annuleren, zie pagina 20.

Raadpleeg pagina 33 voor meer informatie over de aansluiting/

installatie.

2GB

Made in Thailand

Laser Diode Properties

 Emission Duration: Continuous

 Laser Output: Less than 53.3 W

(This output is the value measurement at a distance

of 200 mm from the objective lens surface on the

Optical Pick-up Block with 7 mm aperture.)

The nameplate indicating operating voltage, etc., is

located on the bottom of the chassis.

Hereby, Sony Corporation declares that this

equipment is in compliance with Directive 2014/53/

EU.

The full text of the EU declaration of conformity is

available at the following internet address:

http://www.compliance.sony.de/

This equipment is intended to be used with the

approved version(s) of software that are indicated

in the EU Declaration of Conformity.

The software loaded on this equipment is verified

to comply with the essential requirements of the

Directive 2014/53/EU.

Software version: 1_

The software version can be checked in the

firmware setup item of the general setup menu.

Notice for customers: the following

information is only applicable to equipment

sold in countries applying EU Directives

Manufacturer: Sony Corporation, 1-7-1 Konan

Minato-ku Tokyo, 108-0075 Japan

For EU product compliance: Sony Belgium,

bijkantoor van Sony Europe Limited, Da Vincilaan

7-D1, 1935 Zaventem, Belgium

Disposal of waste batteries and

electrical and electronic

equipment (applicable in the

European Union and other

European countries with separate

collection systems)

This symbol on the product, the battery or on the

packaging indicates that the product and the

battery shall not be treated as household waste.

On certain batteries this symbol might be used in

combination with a chemical symbol. The chemical

symbols for mercury (Hg) or lead (Pb) are added if

the battery contains more than 0.0005% mercury or

0.004% lead.

By ensuring these products and batteries are

disposed of correctly, you will help prevent

potentially negative consequences for the

environment and human health which could

otherwise be caused by inappropriate waste

handling. The recycling of the materials will help to

conserve natural resources.

In case of products that for safety, performance or

data integrity reasons require a permanent

connection with an incorporated battery, this

battery should be replaced by qualified service staff

only.

To ensure that the battery and the electrical and

electronic equipment will be treated properly, hand

over these products at end-of-life to the applicable

collection point for the recycling of electrical and

electronic equipment.

For all other batteries, please view the section on

how to remove the battery from the product safely.

Hand the battery over to the applicable collection

point for the recycling of waste batteries.

For more detailed information about recycling of

this product or battery, please contact your local

Civic Office, your household waste disposal service

or the shop where you purchased the product or

battery.

Disclaimer regarding services offered by third

parties

Services offered by third parties may be changed,

suspended, or terminated without prior notice.

Sony does not bear any responsibility in these sorts

of situations.

For safety, be sure to install this unit in the

dashboard of the car as the rear side of the unit

becomes hot during use.

For details, see “Connection/Installation”

(page 30).

Warning if your car’s ignition has no ACC

position

Be sure to set the AUTO OFF function (page 18).

The unit will shut off completely and

automatically in the set time after the unit is

turned off, which prevents battery drain. If you

do not set the AUTO OFF function, press and hold

OFF until the display disappears each time you

turn the ignition off.

3GB

Caution

IN NO EVENT SHALL SONY BE LIABLE FOR ANY

INCIDENTAL, INDIRECT OR CONSEQUENTIAL

DAMAGES OR OTHER DAMAGES INCLUDING,

WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF

REVENUE, LOSS OF DATA, LOSS OF USE OF THE

PRODUCT OR ANY ASSOCIATED EQUIPMENT,

DOWNTIME, AND PURCHASER’S TIME RELATED TO

OR ARISING OUT OF THE USE OF THIS PRODUCT, ITS

HARDWARE AND/OR ITS SOFTWARE.

Dear customer, this product includes a radio

transmitter.

According to UNECE Regulation no. 10, a vehicle

manufacturers may impose specific conditions for

installation of radio transmitters into vehicles.

Please check your vehicle operation manual or

contact the manufacturer of your vehicle or your

vehicle dealer, before you install this product into

your vehicle.

Emergency calls

This BLUETOOTH car handsfree and the electronic

device connected to the handsfree operate using

radio signals, cellular, and landline networks as well

as user-programmed function, which cannot

guarantee connection under all conditions.

Therefore do not rely solely upon any electronic

device for essential communications (such as

medical emergencies).

On BLUETOOTH communication

 Microwaves emitting from a BLUETOOTH device

may affect the operation of electronic medical

devices. Turn off this unit and other BLUETOOTH

devices in the following locations, as it may cause

an accident.

 where inflammable gas is present, in a hospital,

train, airplane, or petrol station

 near automatic doors or a fire alarm

 This unit supports security capabilities that

comply with the BLUETOOTH standard to provide

a secure connection when the BLUETOOTH

wireless technology is used, but security may not

be enough depending on the setting. Be careful

when communicating using BLUETOOTH wireless

technology.

 We do not take any responsibility for the leakage

of information during BLUETOOTH

communication.

If you have any questions or problems concerning

your unit that are not covered in this manual,

consult your nearest Sony dealer.

Important notice

4GB

Table of Contents

Guide to Parts and Controls . . . . . . . . . . . . . . . . . . . 5

Getting Started

Detaching the Front Panel . . . . . . . . . . . . . . . . . . . . 6

Resetting the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Preparing a BLUETOOTH Device. . . . . . . . . . . . . . . . 7

Connecting a USB Device . . . . . . . . . . . . . . . . . . . . . 9

Connecting Other Portable Audio Device . . . . . . . . 9

Listening to the Radio

Receiving DAB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Using FM/MW/LW. . . . . . . . . . . . . . . . . . . . . . . . . . 11

Using Radio Data System (RDS) . . . . . . . . . . . . . . . 11

Playback

Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Playing a USB Device . . . . . . . . . . . . . . . . . . . . . . . 12

Playing a BLUETOOTH Device. . . . . . . . . . . . . . . . . 13

Searching and Playing Tracks. . . . . . . . . . . . . . . . . 13

Handsfree Calling (via BLUETOOTH

only)

Receiving a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Making a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Available Operations during Call . . . . . . . . . . . . . . 15

Useful Functions

SongPal with iPhone/Android smartphone . . . . . 16

Using Siri Eyes Free . . . . . . . . . . . . . . . . . . . . . . . . . 17

Settings

Canceling the DEMO Mode . . . . . . . . . . . . . . . . . . 18

Basic Setting Operation . . . . . . . . . . . . . . . . . . . . . 18

General Setup (GENERAL). . . . . . . . . . . . . . . . . . . . 18

Sound Setup (SOUND) . . . . . . . . . . . . . . . . . . . . . . 19

Display Setup (DISPLAY) . . . . . . . . . . . . . . . . . . . . . 21

BLUETOOTH Setup (BLUETOOTH). . . . . . . . . . . . . . 21

SongPal Setup (SONGPAL) . . . . . . . . . . . . . . . . . . . 21

Additional Information

Updating the Firmware. . . . . . . . . . . . . . . . . . . . . . 22

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Connection/Installation

Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Parts List for Installation . . . . . . . . . . . . . . . . . . . . 30

Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

5GB

Guide to Parts and Controls

Front panel removed (inner panel)

The number 3/ (repeat) button has a tactile dot.

 (browse) (page 10, 13, 14)

During DAB reception:

Enter the browse mode.

During playback:

Enter the browse mode.

(Not available when an iPod is connected.)

 Front panel release button

 SEEK +/–

During DAB reception:

Select a service. Press and hold to search for an

ensemble.

During FM/MW/LW reception:

Tune in radio stations automatically. Press and

hold to tune manually.

/ (prev/next)

/ (fast-reverse/fast-forward)

 Control dial

Rotate to adjust the volume.

PUSH ENTER

Enter the selected item.

Press SRC, rotate then press to change the

source (timeout in 2 seconds).

VOICE (page 15, 17)

Activate voice dial, voice recognition (Android™

smartphone only), or the Siri function (iPhone

only).

APP (page 16)

Press and hold for more than 2 seconds to

establish “SongPal” function (connection).

N-Mark

Touch the control dial with Android smartphone

to make BLUETOOTH connection.

 Receptor for the remote commander

 Disc slot

 Display window

 (disc eject)

 SRC (source)

Turn on the power.

Change the source.

OFF

Press and hold for 1 second to turn the source

off and display the clock.

Press and hold for more than 2 seconds to turn

off the power and the display.

 (back)

Return to the previous display.

MODE (page 10, 11, 15)

 CALL

Enter the call menu. Receive/end a call.

Press and hold more than 2 seconds to switch

the BLUETOOTH signal.

Main unit

6GB

 MENU

Open the setup menu.

DSPL (display)

Press and hold, then press to change display

items.

 Number buttons (1 to 6)

Receive stored DAB services or radio stations.

Press and hold to store DAB services or radio

stations.

ALBUM /

Skip an album for audio device. Press and hold

to skip albums continuously.

(Not available when an iPod is connected.)

(repeat)

(shuffle)

MIC (page 15)

PAUSE

 AF (alternative frequencies)/TA (traffic

announcement)

Set AF and TA.

PTY (program type)

Press and hold to select PTY in DAB or RDS.

 AUX input jack

 USB port

 RESET (inner panel) (page 7)

Detaching the Front Panel

You can detach the front panel of this unit to

prevent theft.

1 Press and hold OFF  until the unit turns

off, press the front panel release button

, then pull the panel towards you to

remove.

Caution alarm

If you turn the ignition switch to the OFF position

without detaching the front panel, the caution

alarm will sound for a few seconds. The alarm will

only sound if the built-in amplifier is used.

Serial numbers

Make sure the serial numbers on the bottom of the

unit and the back of the front panel are matched

correctly. Otherwise you cannot make BLUETOOTH

pairing, connection and disconnection by NFC.

Getting Started

Attaching the front panel

7GB

Resetting the Unit

Before operating the unit for the first time, after

replacing the car battery, or changing the

connections, you must reset the unit.

Press RESET on the inner panel with a ball-point

pen, etc., after detaching the front panel.

Note

Resetting the unit will erase the clock setting and some

stored contents.

Setting the Clock

1 Press MENU, rotate the control dial to

select [GENERAL], then press it.

2 Rotate the control dial to select [SET

CLOCK-ADJ], then press it.

The hour indication flashes.

3 Rotate the control dial to set the hour

and minute.

To move the digital indication, press SEEK +/–.

4 After setting the minute, press MENU.

The setup is complete and the clock starts.

To display the clock

Press and hold DSPL.

Preparing a BLUETOOTH Device

You can enjoy music, or perform handsfree calling

depending on the BLUETOOTH compatible device

such as a smartphone, cellular phone and audio

device (hereafter “BLUETOOTH device” if not

otherwise specified). For details on connecting,

refer to the operating instructions supplied with the

device.

Before connecting the device, turn down the

volume of this unit; otherwise, loud sound may

result.

By touching the control dial on the unit with an

NFC* compatible smartphone, the unit is paired and

connected with the smartphone automatically.

* NFC (Near Field Communication) is a technology

enabling short-range wireless communication

between various devices, such as mobile phones and

IC tags. Thanks to the NFC function, data

communication can be achieved easily just by

touching the relevant symbol or designated location

on NFC compatible devices.

For a smartphone with Android OS 4.0 or lower

installed, downloading the app “NFC Easy Connect”

available at Google Play™ is required. The app may

not be downloadable in some countries/regions.

1 Activate the NFC function on the

smartphone.

For details, refer to the operating instructions

supplied with the smartphone.

2 Touch the N-Mark part of the unit with

the N-Mark part of the smartphone.

Make sure that lights up on the display of the

unit.

To disconnect by One touch

Touch the N-Mark part of the unit with the N-Mark

part of the smartphone again.

Notes

 When making the connection, handle the

smartphone carefully to prevent scratches.

 One touch connection is not possible when the unit is

already connected to two NFC compatible devices. In

this case, disconnect either device, and make

connection with the smartphone again.

Connecting with a Smartphone by One

touch (NFC)

8GB

When connecting a BLUETOOTH device for the first

time, mutual registration (called “pairing”) is

required. Pairing enables this unit and other devices

to recognize each other. This unit can connect two

BLUETOOTH devices (two cellular phones, or a

cellular phone and an audio device).

1 Place the BLUETOOTH device within 1 m

(3 ft) of this unit.

2 Press MENU, rotate the control dial to

select [BLUETOOTH], then press it.

3 Rotate the control dial to select [SET

PAIRING], then press it.

4 Rotate the control dial to select [SET

DEVICE 1]* or [SET DEVICE 2]*, then press

it.

flashes while the unit is in pairing standby

mode.

* [SET DEVICE 1] or [SET DEVICE 2] will be changed

to the paired device name after pairing is

complete.

5 Perform pairing on the BLUETOOTH

device so it detects this unit.

6 Select [MEX-N6002BD] shown in the

display of the BLUETOOTH device.

If your model name does not appear, repeat

from step 2.

7 If passkey* input is required on the

BLUETOOTH device, input [0000].

* Passkey may be called “Passcode,” “PIN code,”

“PIN number” or “Password,” etc., depending on

the device.

When pairing is made, stays lit.

8 Select this unit on the BLUETOOTH device

to establish the BLUETOOTH connection.

or lights up when the connection is made.

Note

While connecting to a BLUETOOTH device, this unit

cannot be detected from another device. To enable

detection, enter the pairing mode and search for this

unit from another device.

To start playback

For details, see “Playing a BLUETOOTH Device”

(page 13).

To disconnect the paired device

Perform steps 2 to 4 to disconnect after this unit

and the BLUETOOTH device are paired.

To use a paired device, connection with this unit is

required. Some paired devices will connect

automatically.

1 Press MENU, rotate the control dial to

select [BLUETOOTH], then press it.

2 Rotate the control dial to select [SET BT

SIGNL], then press it.

Make sure that lights up.

3 Activate the BLUETOOTH function on the

BLUETOOTH device.

4 Operate the BLUETOOTH device to

connect to this unit.

or lights up.

Icons in the display:

To connect the last-connected device from

this unit

Activate the BLUETOOTH function on the

BLUETOOTH device.

To connect with the audio device, press SRC to

select [BT AUDIO] and press PAUSE.

To connect with the cellular phone, press CALL.

Pairing and connecting with a

BLUETOOTH device

[0000]

Input passkey

Connecting with a paired BLUETOOTH

device

Lights up when handsfree calling is

available by enabling the HFP (Handsfree

Profile).

Lights up when the audio device is

playable by enabling the A2DP

(Advanced Audio Distribution Profile).

9GB

Note

While streaming BLUETOOTH audio, you cannot

connect from this unit to the cellular phone. Connect

from the cellular phone to this unit instead.

Tip

With BLUETOOTH signal on: when the ignition is turned

to on, this unit reconnects automatically to the last-

connected cellular phone.

To install the microphone

For details, see “Installing the microphone”

(page 33).

When an iPhone/iPod with iOS5 or later installed is

connected to the USB port, the unit is paired and

connected with the iPhone/iPod automatically.

To enable BLUETOOTH Auto Pairing, make sure [SET

AUTOPAIR] in [BLUETOOTH] is set to [ON] (page 21).

1 Activate the BLUETOOTH function on the

iPhone/iPod.

2 Connect an iPhone/iPod to the USB port.

Make sure that lights up on the display of the

unit.

Notes

 BLUETOOTH Auto Pairing is not possible if the unit is

already connected to two BLUETOOTH devices. In this

case, disconnect the either device, then connect the

iPhone/iPod again.

 If BLUETOOTH Auto Pairing is not established, see

“Preparing a BLUETOOTH Device” for details (page 7).

Connecting a USB Device

1 Turn down the volume on the unit.

2 Connect the USB device to the unit.

To connect an iPod/iPhone, use the USB

connection cable for iPod (not supplied).

Connecting Other Portable

Audio Device

1 Turn off the portable audio device.

2 Turn down the volume on the unit.

3 Connect the portable audio device to the

AUX input jack (stereo mini jack) on the

unit with a connecting cord (not

supplied)*.

* Be sure to use a straight type plug.

4 Press SRC to select [AUX].

To match the volume level of the connected

device to other sources

Start playback of the portable audio device at a

moderate volume, and set your usual listening

volume on the unit.

Press MENU, then select [SOUND]  [SET AUX VOL]

(page 20).

Connecting with an iPhone/iPod

(BLUETOOTH Auto Pairing)

10GB

To listen to the radio, press SRC to select [TUNER].

When the DAB band is selected for the first time

after replacing the car battery or changing the

connections, the initial scan starts automatically.

Allow the initial scan to finish. (If interrupted, the

initial scan will start again the next time you select

the DAB band.) If no DAB station is stored by the

initial scan, perform an auto scan (page 11).

Tip

Set [SET ANT-PWR] to [ON] (default) or [OFF] depending

on the type of DAB antenna (aerial) (page 19).

Receiving DAB

DAB (Digital Audio Broadcasting) is a transmission

system on terrestrial networks. DAB stations bundle

radio programs (“services”) into an ensemble, and

each service contains one or more components.

The same service can sometimes be received on

different frequencies.

1 Press MODE to select [DB1], [DB2] or

[DB3].

2 Press SEEK +/– to search within an

ensemble for a service; press and hold

SEEK +/– to search for different

ensembles.

Scanning stops when the unit receives a

service/ensemble. Search until the desired

service is received.

1 While receiving the service that you want

to store, press and hold a number button

(1 to 6) until [MEM] appears.

1 After selecting the desired band, press a

number button (1 to 6).

You can display a list of services for easy searching.

1 During DAB reception, press (browse).

The unit enters Quick-BrowZer mode, and the

list of services appears.

2 Rotate the control dial to select the

desired service, then press it.

Reception starts.

To exit the Quick-BrowZer mode

Press (browse).

If you enable DAB announcements, DAB

announcements can interrupt the currently

selected source.

1 Press MENU, rotate the control dial to

select [GENERAL], then press it.

2 Rotate the control dial to select [SET

ANNOUNCE], then press it.

3 Rotate the control dial to select [SET

ANNC-ON] or [SET ANNC-OFF], then press

it.

Note

During a DAB announcement, the volume is adjusted to

the level set for TA in RDS (page 11).

To listen to the same or similar program even

during weak reception

Set [SET SOFTLINK] to [ON] (page 19).

[FM-LINK] lights up when the corresponding FM

program is being received.

“Hard Link” follows the same program, and “Soft

Link” follows a similar program.

Listening to the Radio

Searching for a service manually

Storing a service manually

Receiving stored services

Searching for a service by name (Quick-

BrowZer™)

Setting DAB announcements

SOFT

LINK

DAB FM

Hard

Link

Soft

Link

Hard

Link

Soft

Link

OFF 

ON 

11GB

1 Press MODE to select [DB1], [DB2] or

[DB3].

2 Press MENU, rotate the control dial to

select [GENERAL], then press it.

3 Rotate the control dial to select [SET

AUTOSCAN], then press it.

The unit updates the list of services in Quick-

BrowZer mode.

Using FM/MW/LW

1 Press MODE to change the band (FM1,

FM2, MW or LW).

2 Press MENU, rotate the control dial to

select [GENERAL], then press it.

3 Rotate the control dial to select [SET

BTM], then press it.

The unit stores stations in order of frequency on

the number buttons.

1 Press MODE to change the band (FM1,

FM2, MW or LW).

2 Perform tuning.

To tune manually

Press and hold SEEK +/– to locate the

approximate frequency, then press SEEK +/–

repeatedly to fine adjust to the desired

frequency.

To tune automatically

Press SEEK +/–.

Scanning stops when the unit receives a station.

1 While receiving the station that you want

to store, press and hold a number button

(1 to 6) until [MEM] appears.

1 Select the band, then press a number

button (1 to 6).

Using Radio Data System (RDS)

AF continuously retunes the station to the strongest

signal in a network, and TA provides current traffic

information or traffic programs (TP) if received.

1 Press AF/TA to select [AF-ON], [TA-ON],

[AF/TA-ON] or [AF/TA-OFF].

To store RDS stations with the AF and TA

setting

You can preset RDS stations along with an AF/TA

setting. Set AF/TA, then store the station with BTM

or manually. If you preset manually, you can also

preset non-RDS stations.

To receive emergency announcements

With AF or TA on, emergency announcements will

automatically interrupt the currently selected

source.

To adjust the volume level during a traffic

announcement

Level will be stored into memory for subsequent

traffic announcements, independently from the

regular volume level.

To stay with one regional program

(REGIONAL)

When the AF and REGIONAL functions are on, you

will not be switched to another regional station

with a stronger frequency. If you leave this regional

program’s reception area, set [SET REG-OFF] in

[GENERAL] during FM reception (page 19).

This function does not work in the UK and some

other areas.

Updating the service list automatically

(Auto scan)

Storing automatically (BTM)

Tuning

Storing manually

Receiving the stored stations

Setting alternative frequencies (AF) and

traffic announcement (TA)

12GB

Local Link function (UK only)

This function enables you to select other local

stations in the area, even if they are not stored on

your number buttons.

During FM reception, press a number button (1 to 6)

on which a local station is stored. Within 5 seconds,

press again a number button of the local station.

Repeat this procedure until the local station is

received.

Use PTY to display or search for a desired program

type.

During DAB reception

1 Press and hold PTY.

2 Rotate the control dial until the desired

program type appears, then press it.

The unit lists all services in the selected program

type.

3 Rotate the control dial until the desired

service appears, then press it.

Reception starts.

During FM reception

1 Press and hold PTY.

2 Rotate the control dial until the desired

program type appears, then press it.

The unit starts to search for a station

broadcasting the selected program type.

Type of programs

* May appear depending on the service during DAB

reception.

The CT data from the RDS transmission sets the

clock.

1 Set [SET CT-ON] in [GENERAL] (page 19).

Playing a Disc

1 Insert the disc (label side up).

Playback starts automatically.

Playing a USB Device

In these Operating Instructions, “iPod” is used as a

general reference for the iPod functions on an iPod

and iPhone, unless otherwise specified by the text

or illustrations.

For details on the compatibility of your iPod, see

“About iPod” (page 22) or visit the support site on

the back cover.

MSC (Mass Storage Class) and MTP (Media Transfer

Protocol) type USB devices* compliant with the USB

standard can be used. Some digital media players

or Android smartphones may require setting to

MTP mode.

* e.g., a USB flash drive, digital media player, Android

smartphone

Notes

 For details on the compatibility of your USB device,

visit the support site on the back cover.

 Playback of the following files is not supported.

MP3/WMA/AAC/FLAC:

 copyright-protected files

 DRM (Digital Rights Management) files

 Multi-channel audio files

MP3/WMA/AAC:

 lossless compression files

WAV:

 Multi-channel audio files

1 Connect a USB device to the USB port

(page 9).

Playback starts.

If a device is already connected, to start

playback, press SRC to select [USB] ([IPD]

appears in the display when the iPod is

recognized).

2 Adjust the volume on this unit.

Selecting program types (PTY)

NONE (No Program Type)*, NEWS (News), AFFAIRS

(Current Affairs), INFO (Information), SPORT

(Sports), EDUCATE (Education), DRAMA (Drama),

CULTURE (Culture), SCIENCE (Science), VARIED

(Varied), POP M (Pop Music), ROCK M (Rock Music),

EASY M (M.O.R. Music), LIGHT M (Light classical),

CLASSICS (Serious classical), OTHER M (Other

Music), WEATHER (Weather), FINANCE (Finance),

CHILDREN (Children’s program), SOCIAL A (Social

Affairs), RELIGION (Religion), PHONE IN (Phone In),

TRAVEL (Travel), LEISURE (Leisure), JAZZ (Jazz

Music), COUNTRY (Country Music), NATION M

(National Music), OLDIES (Oldies Music), FOLK M

(Folk Music), DOCUMENT (Documentary)

Setting clock time (CT)

Playback

13GB

To stop playback

Press and hold OFF for 1 second.

To remove the device

Stop playback, then remove the device.

Caution for iPhone

When you connect an iPhone via USB, phone call

volume is controlled by the iPhone, not the unit. Do

not inadvertently increase the volume on the unit

during a call, as a sudden loud sound may result

when the call ends.

Playing a BLUETOOTH Device

You can play contents on a connected device that

supports BLUETOOTH A2DP (Advanced Audio

Distribution Profile).

1 Make BLUETOOTH connection with the

audio device (page 7).

To select the audio device, press MENU, then

select [BLUETOOTH]  [SET AUDIODEV]

(page 21).

2 Press SRC to select [BT AUDIO].

3 Operate the audio device to start

playback.

4 Adjust the volume on this unit.

Notes

 Depending on the audio device, information such as

title, track number/time and playback status may not

be displayed on this unit.

 Even if the source is changed on this unit, playback of

the audio device does not stop.

 [BT AUDIO] does not appear in the display while

running the “SongPal” application via the BLUETOOTH

function.

To match the volume level of the BLUETOOTH

device to other sources

Start playback of the BLUETOOTH audio device at a

moderate volume, and set your usual listening

volume on the unit.

Press MENU, then select [SOUND]  [SET BTA VOL]

(page 20).

Searching and Playing Tracks

1 During playback, press (repeat) or

(shuffle) repeatedly to select the desired

play mode.

Playback in the selected play mode may take

time to start.

Available play modes differ depending on the

selected sound source.

Not available when an iPod is connected.

1 During CD, USB or BT AUDIO*

1

playback,

press (browse)*

2

to display the list of

search categories.

When the track list appears, press (back)

repeatedly to display the desired search

category.

*1 Available only for audio devices supporting

AVRCP (Audio Video Remote Control Profile) 1.4

or above.

*2 During USB playback, press (browse) for

more than 2 seconds to directly return to the

beginning of the category list.

2 Rotate the control dial to select the

desired search category, then press it to

confirm.

3 Repeat step 2 to search the desired track.

Playback starts.

To exit the Quick-BrowZer mode

Press (browse).

Repeat play and shuffle play

Searching a track by name (Quick-

BrowZer)

14GB

Not available when an iPod is connected.

1 Press (browse).

2 Press SEEK +.

3 Rotate the control dial to select the item.

The list is jumped in steps of 10% of the total

number of items.

4 Press ENTER to return to the Quick-

BrowZer mode.

The selected item appears.

5 Rotate the control dial to select the

desired item, then press it.

Playback starts.

To use a cellular phone, connect it with this unit.

You can connect two cellular phones to the unit. For

details, see “Preparing a BLUETOOTH Device”

(page 7).

Receiving a Call

1 Press CALL when a call is received with a

ringtone.

The phone call starts.

Note

The ringtone and talker’s voice are output only from the

front speakers.

To reject the call

Press and hold OFF for 1 second.

To end the call

Press CALL again.

Making a Call

You can make a call from the phonebook or call

history when a cellular phone supporting PBAP

(Phone Book Access Profile) is connected.

When two cellular phones are connected to the

unit, select either phone.

1 Press CALL.

When two cellular phones are connected to the

unit, rotate the control dial to select either

phone, then press it.

2 Rotate the control dial to select [PHONE

BOOK], then press it.

3 Rotate the control dial to select an initial

from the initial list, then press it.

4 Rotate the control dial to select a name

from the name list, then press it.

Searching by skipping items

(Jump mode)

Handsfree Calling (via BLUETOOTH

only)

From the phonebook

15GB

5 Rotate the control dial to select a

number from the number list, then press

it.

The phone call starts.

1 Press CALL.

When two cellular phones are connected to the

unit, rotate the control dial to select either

phone, then press it.

2 Rotate the control dial to select [RECENT

CALL], then press it.

A list of the call history appears.

3 Rotate the control dial to select a name

or phone number from the call history,

then press it.

The phone call starts.

1 Press CALL.

When two cellular phones are connected to the

unit, rotate the control dial to select either

phone, then press it.

2 Rotate the control dial to select [DIAL

NUMBER], then press it.

3 Rotate the control dial to enter the

phone number, and lastly select [ ]

(space), then press ENTER*.

The phone call starts.

* To move the digital indication, press SEEK +/–.

Note

[_] appears instead of [#] on the display.

1 Press CALL.

When two cellular phones are connected to the

unit, rotate the control dial to select either

phone, then press it.

2 Rotate the control dial to select [REDIAL],

then press it.

The phone call starts.

You can make a call by saying the voice tag stored

in a connected cellular phone that has a voice

dialing function.

1 Press CALL.

When two cellular phones are connected to the

unit, rotate the control dial to select either

phone, then press it.

2 Rotate the control dial to select [VOICE

DIAL], then press it.

Alternatively, press VOICE while the “SongPal”

function is off.

3 Say the voice tag stored on the cellular

phone.

Your voice is recognized, and the call is made.

To cancel voice dialing

Press VOICE.

Available Operations during

Call

To adjust the ringtone volume

Rotate the control dial while receiving a call.

To adjust the talker’s voice volume

Rotate the control dial during a call.

To adjust the volume for the other party (Mic

gain adjustment)

Press MIC.

Adjustable volume levels: [MIC-LOW], [MIC-MID],

[MIC-HI].

To reduce echo and noise (Echo Canceler/

Noise Canceler Mode)

Press and hold MIC.

Settable mode: [EC/NC-1], [EC/NC-2].

To switch between handsfree mode and

handheld mode

During a call, press MODE to switch the phone call

audio between the unit and cellular phone.

Note

Depending on the cellular phone, this operation may

not be available.

From the call history

By phone number input

By redial

By voice tags

16GB

SongPal with iPhone/Android

smartphone

Downloading the latest version

of “SongPal” application is

required from the App Store for

iPhone or from Google Play for

Android smartphone.

Notes

 For your safety, follow your local

traffic laws and regulations, and

do not operate the application

while driving.

 “SongPal” is an app for

controlling Sony audio devices

which are compatible with “SongPal”, by your iPhone/

Android smartphone.

 What you can control with “SongPal” varies

depending on the connected device.

 To make use of “SongPal” features, see the details on

your iPhone/Android smartphone.

 For further details on “SongPal,” visit the following

URL: http://rd1.sony.net/help/speaker/songpal/

 Visit the website below and check the compatible

iPhone/Android smartphone models.

For iPhone: visit the App Store

For Android smartphone: visit Google Play

1 Make the BLUETOOTH connection with

iPhone/Android smartphone (page 7).

To select the audio device, press MENU, then

select [BLUETOOTH]  [SET AUDIODEV]

(page 21).

2 Launch the “SongPal” application.

*1

3 Press and hold APP on the unit for more

than 2 seconds.

*2

Connection to iPhone/Android smartphone

starts.

For details on the operations on iPhone/

Android smartphone, see the help of the

application.

*1 If [AUTO LAUNCH] in [SONGPAL] is set to [ON]

(page 21), the “SongPal” connection is

established automagically when the BLUETOOTH

signal of iPhone/Android smartphone is turned

on.

*2 Alternatively, press MENU, then select [SONGPAL]

 [CONNECT] (page 21).

If the device number appears

Make sure that the number is displayed (e.g.,

123456), then select [Yes] on the iPhone/Android

smartphone.

To terminate connection

1 Press MENU, rotate the control dial to select

[SONGPAL], then press it.

2 Rotate the control dial to select [CONNECT], then

press it.

Selecting the source or application

You can operate to select the desired source or

application on iPhone/Android smartphone.

To select the source

Press SRC repeatedly. Alternatively, press SRC,

rotate the control dial to select the desired source,

then press ENTER.

To display the source list

Press SRC.

Announcement of various information by

voice guide (Android smartphone only)

When SMS, Twitter/Facebook/Calendar

notifications, etc., are received, they are

automatically announced through the car speakers.

For details on settings, refer to the help of the

application.

Useful Functions

Establishing the SongPal connection

17GB

Activating voice recognition (Android

smartphone only)

By registering applications, you can control an

application by voice command. For details, refer to

the help of the application.

To activate voice recognition

1 Press VOICE to activate voice recognition.

2 Say the desired voice command into the

microphone when [Say Source or App] appears on

the Android smartphone.

Notes

 Voice recognition may not be available in some cases.

 Voice recognition may not work properly depending

on the performance of the connected Android

smartphone.

 Operate under conditions where noise such as engine

sound is minimized during voice recognition.

Replying a message of SMS (Android

smartphone only)

You can reply a message by voice recognition.

1 Activate voice recognition, then input “Reply.”

The message input display appears on the “SongPal”

application.

2 Input a reply message by voice recognition.

The list of message candidates appears on the

“SongPal” application.

3 Rotate the control dial to select the desired

message, then press it.

The message is sent out.

Making sound and display settings

You can adjust the settings relating to sound and

display via iPhone/Android smartphone.

For details on settings, refer to the help of the

application.

Using Siri Eyes Free

Siri Eyes Free allows you to use an iPhone

handsfree by simply speaking into the microphone.

This function requires you to connect an iPhone to

the unit via BLUETOOTH. Availability is limited

iPhone 4s or later. Make sure that your iPhone is

running the latest iOS version.

You must complete BLUETOOTH registration and

connection configurations for the iPhone with the

unit in advance. For details, see “Preparing a

BLUETOOTH Device” (page 7).

To select the iPhone, press MENU, then select

[BLUETOOTH]  [SET AUDIODEV] (page 21).

1 Activate the Siri function on the iPhone.

For details, refer to the operating instructions

supplied with the iPhone.

2 Press VOICE.

The voice command display appears.

3 After the iPhone beeps, speak into the

microphone.

The iPhone beeps again, then Siri starts

responding.

To deactivate Siri Eyes Free

Press VOICE.

Notes

 The iPhone may not recognize your voice depending

on usage conditions. (For example, if you are in a

moving car.)

 Siri Eyes Free may not function properly, or the

response time may lag in locations where iPhone

signals are difficult to receive.

 Depending on the iPhone’s operating condition, Siri

Eyes Free may not function properly, or may quit.

 If you play a track with an iPhone using the

BLUETOOTH audio connection, when the track starts

playback via BLUETOOTH, Siri Eyes Free automatically

quits and the unit switches to the BLUETOOTH audio

source.

 When Siri Eyes Free is activated during audio

playback, the unit may switch to the BLUETOOTH

audio source even if you do not specify a track to play.

 When connecting the iPhone to the USB port, Siri Eyes

Free may not function properly, or may quit.

 When connecting the iPhone to the unit via USB, do

not activate Siri with the iPhone. Siri Eyes Free may

not function properly, or may quit.

 There is no audio sound while Siri Eyes Free is

activated.

18GB

Canceling the DEMO Mode

You can cancel the demonstration display which

appears when the source is off and the clock is

displayed.

1 Press MENU, rotate the control dial to

select [GENERAL], then press it.

2 Rotate the control dial to select [SET

DEMO], then press it.

3 Rotate the control dial to select [SET

DEMO-OFF], then press it.

The setting is complete.

4 Press (back) twice.

The display returns to normal reception/play

mode.

Basic Setting Operation

You can set items in the following setup categories:

General setup (GENERAL), Sound setup (SOUND),

Display setup (DISPLAY), BLUETOOTH setup

(BLUETOOTH), SongPal setup (SONGPAL)

1 Press MENU.

2 Rotate the control dial to select the setup

category, then press it.

The items that can be set differ depending on

the source and settings.

3 Rotate the control dial to select the

options, then press it.

To return to the previous display

Press (back).

General Setup (GENERAL)

DEMO (demonstration)

Activates the demonstration: [ON], [OFF].

CLOCK-ADJ (clock adjust) (page 7)

CAUT ALM (caution alarm)

Activates the caution alarm: [ON], [OFF]

(page 6).

(Available only while the source is off and the

clock is displayed.)

BEEP

Activates the beep sound: [ON], [OFF].

AUTO OFF

Shuts off automatically after a certain time when

the unit is turned off: [ON] (30 minutes), [OFF].

STEERING

Registers/resets the setting of the steering

wheel remote control.

(Available only while the source is off and the

clock is displayed.)

STR CONTROL (steering control)

Selects the input mode of the connected remote

control. To prevent a malfunction, be sure to

match the input mode with the connected

remote control before use.

CUSTOM

Input mode for the steering wheel remote

control

PRESET

Input mode for the wired remote control

excluding the steering wheel remote control

EDIT CUSTOM

Registers the functions (SOURCE, ATT, VOL +/–,

SEEK +/–, VOICE, ON HOOK, OFF HOOK) to the

steering wheel remote control:

 Rotate the control dial to select the function

you want to assign to the steering wheel

remote control, then press it.

 While [REGISTER] is blinking, press and hold

the button on the steering wheel remote

control you want to assign the function to.

When registration is complete, [REGISTERED]

is displayed.

 To register other functions, repeat steps 

and .

(Available only when [STR CONTROL] is set to

[CUSTOM].)

RESET CUSTOM

Resets the registered functions of the steering

wheel remote control: [YES], [NO].

(Available only when [STR CONTROL] is set to

[CUSTOM].)

Notes

 While making settings, only button operation on

the unit is available. For safety, park your car

before making this setting.

 If an error occurs while registering, all the

previously-registered information remains. Restart

registration from the function where the error

occurred.

 This function may not be available on some

vehicles. For details on the compatibility of your

vehicle, visit the support site on the back cover.

Settings

19GB

CT (clock time)

Activates the CT function: [ON], [OFF].

REGIONAL

Restricts reception to a specific region: [ON],

[OFF]. (Available only when FM is received.)

BTM (best tuning memory) (page 11)

(Available only when the tuner (FM/MW/LW) is

selected.)

ANNOUNCE (announcement)

Enables broadcast announcements (page 10).

(Not available when the source is off and the

clock is displayed.)

SOFTLINK

Searches for and tunes to the similar program

automatically when the signal of the current

program is too weak to receive: [ON], [OFF].

(Available only during DAB reception.)

ANT-PWR (antenna power)

Supplies power to the DAB antenna (aerial) input

terminal: [ON], [OFF].

(Available only when the unit is turned off and

during DAB reception.)

AUTOSCAN (auto scan)

Performs an auto scan to update the list of

services in Quick-BrowZer mode.

(Available only during DAB reception.)

FIRMWARE

(Available only while the source is off and the

clock is displayed.)

Checks/updates the firmware version. For

details, visit the support site on the back cover.

FW VERSION (firmware version)

Displays current firmware version.

FW UPDATE (firmware update)

Enters firmware update process: [YES], [NO].

Updating the firmware takes a few minutes to

complete. During the update, do not turn the

ignition to the OFF position, nor remove the USB

device.

Sound Setup (SOUND)

This setup menu is not available when the source is

off and the clock is displayed.

EXTRA BASS

Reinforces bass sound in synchronization with

the volume level: [1], [2], [OFF].

(Automatically sets to [OFF] when [C.AUDIO+] is

set to [ON].)

C.AUDIO+ (ClearAudio+)

Reproduces sound by optimizing the digital

signal with the Sony recommended sound

settings: [ON], [OFF]. (Automatically sets to [OFF]

when [EQ10 PRESET] is changed and/or [EXTRA

BASS] is set to [1] or [2] and/or [DSO] is set to

[LOW], [MID] or [HIGH].)

EQ10 PRESET

Selects an equalizer curve from 10 equalizer

curves or off: [OFF], [R&B], [ROCK], [POP],

[DANCE], [HIP-HOP], [ELECTRONICA], [JAZZ],

[SOUL], [COUNTRY], [CUSTOM].

The equalizer curve setting can be memorized

for each source.

EQ10 CUSTOM

Sets [CUSTOM] of EQ10.

Setting the equalizer curve: [BAND1] 32 Hz,

[BAND2] 63 Hz, [BAND3] 125 Hz, [BAND4] 250 Hz,

[BAND5] 500 Hz, [BAND6] 1 kHz, [BAND7] 2 kHz,

[BAND8] 4 kHz, [BAND9] 8 kHz, [BAND10] 16 kHz.

The volume level is adjustable in 1 dB steps,

from -6 dB to +6 dB.

POSITION (listening position)

F/R POS (front/rear position)

Simulates a natural sound field by delaying the

sound output from speakers to suit your position:

 [FRONT L] (front left),

 [FRONT R] (front right),

 [FRONT] (center front),

 [ALL] (center of your car),

[CUSTOM] (position set by the advanced car

audio settings on SongPal)

[OFF] (no position set)

ADJ POSITION (adjust position)

Fine-tunes the listening position setting: [+3] –

[CENTER] – [-3].

(Available only when [F/R POS] is not set to [OFF]

or [CUSTOM].)

SW POS (subwoofer position)

 [NEAR] (near),

 [NORMAL] (normal),

 [FAR] (far)

(Available only when [F/R POS] is set to other

than [OFF].)

DSO (dynamic stage organizer)

Creates a more ambient sound as if there were

speakers in the dashboard: [OFF], [LOW], [MID],

[HIGH].

(Automatically sets to [OFF] when [C.AUDIO+] is

set to [ON].)

20GB

BALANCE

Adjusts the sound balance: [RIGHT-15] –

[CENTER] – [LEFT-15].

FADER

Adjusts the relative level: [FRONT-15] – [CENTER]

– [REAR-15].

DSEE (digital sound enhancement engine)

Improves digitally compressed sound by

restoring high frequencies lost in the

compression process: [ON], [OFF].

This setting can be memorized for each source

other than the tuner.

AAV (advanced auto volume)

Adjusts the playback volume level of all

playback sources to the optimum level: [ON],

[OFF].

RB ENH (rear bass enhancer)

Enhances the bass sound by applying a low pass

filter setting to the rear speakers. This function

allows the rear speakers to work as a subwoofer

if one is not connected.

(Available only when [SW DIREC] is set to [OFF].)

RBE MODE (rear bass enhancer mode)

Selects the rear bass enhancer mode: [1], [2], [3],

[OFF].

LPF FREQ (low pass filter frequency)

Selects the subwoofer cut-off frequency: [50Hz],

[60Hz], [80Hz], [100Hz], [120Hz].

LPF SLOP (low pass filter slope)

Selects the LPF slope: [1], [2], [3].

SW DIREC (subwoofer direct connection)

Adjusts the settings for the subwoofer

connected to the rear speaker lead without a

power amplifier.

(Available only when [RBE MODE] is set to [OFF].)

Be sure to connect a 4  – 8  subwoofer to

either of the rear speaker leads. Do not connect

a speaker to the other rear speaker lead.

SW MODE (subwoofer mode)

Selects the subwoofer mode: [1], [2], [3], [OFF].

SW PHASE (subwoofer phase)

Selects the subwoofer phase: [NORM], [REV].

SW POS (subwoofer position)

Selects the subwoofer position: [NEAR],

[NORMAL], [FAR].

(Available only when [F/R POS] is set to other

than [OFF].)

LPF FREQ (low pass filter frequency)

Selects the subwoofer cut-off frequency: [50Hz],

[60Hz], [80Hz], [100Hz], [120Hz].

LPF SLOP (low pass filter slope)

Selects the LPF slope: [1], [2], [3].

S.WOOFER (subwoofer)

SW LEVEL (subwoofer level)

Adjusts the subwoofer volume level:

[+10 dB] – [0 dB] – [-10 dB].

([ATT] is displayed at the lowest setting.)

SW PHASE (subwoofer phase)

Selects the subwoofer phase: [NORM], [REV].

SW POS (subwoofer position)

Selects the subwoofer position: [NEAR],

[NORMAL], [FAR].

(Available only when [F/R POS] is not set to

[OFF].)

LPF FREQ (low pass filter frequency)

Selects the subwoofer cut-off frequency: [50Hz],

[60Hz], [80Hz], [100Hz], [120Hz].

LPF SLOP (low pass filter slope)

Selects the LPF slope: [1], [2], [3].

HPF (high pass filter)

HPF FREQ (high pass filter frequency)

Selects the front/rear speaker cut-off frequency:

[OFF], [50Hz], [60Hz], [80Hz], [100Hz], [120Hz].

HPF SLOP (high pass filter slope)

Selects the HPF slope (effective only when [HPF

FREQ] is set to other than [OFF]): [1], [2], [3].

AUX VOL (AUX volume level)

Adjusts the volume level for each connected

auxiliary device: [+18 dB] – [0 dB] – [-8 dB].

This setting negates the need to adjust the

volume level between sources.

(Available only when the AUX is selected.)

BTA VOL (BLUETOOTH audio volume level)

Adjusts the volume level for each connected

BLUETOOTH device: [+6 dB] – [0 dB] – [-6 dB].

This setting negates the need to adjust the

volume level between sources.

(Available only when the BT audio or application

is selected.)

La pagina sta caricando ...

Sony MEX-N6002BD Manuale del proprietario

Sony MEX-N6002BD Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti