ProLights 230 W high power LED ellipsoidal profile Manuale utente

Marca: ProLights

Modello: 230 W high power LED ellipsoidal profile

Categoria: Stroboscopi

Tipo: Manuale utente

ECLIPSEHD2

ECLIPSELB05

ECLIPSELB10

ECLIPSELB14

ECLIPSELB19

ECLIPSELB26

ECLIPSELB36

ECLIPSELB50

USER MANUAL

MANUALE UTENTE

ECLIPSEHD2

EN - IT

LED PROFILER

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the

characteristics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

REV.02-11/19

ECLIPSEHD2

Packing content

• ECLIPSEHD2

• Mount bracket

• Power cable

• User manual

TABLE OF CONTENTS

Safety

General instructions

Warnings and installation precautions

1 Introduction

1. 1 Description

1. 2 Technical specifications

1. 3 Configurations

1. 4 Operating elements and connections

2 Installation

2. 1 Mounting

3 Functions and settings

3. 1 Operation

3. 2 Basic

3. 3 Menu structure

3. 4 DMX mode

3. 5 DMX configuration

3. 6 Linking

3. 7 Static mode

3. 8 Auto show mode

3. 9 Master/Slave mode

3. 10 Dimmer mode

3. 11 LED Frequency

3. 12 Fan mode

3. 13 Back Light

3. 14 Fixure information

3. 15 Connection of the DMX line

3. 16 Construction of the DMX termination

3. 17 DMX control

4 Maintenance

4. 1 Maintenance and cleaning the unit

4. 2 Fuse replacement

4. 3 Trouble shooting

ECLIPSEHD2

SAFETY

General instruction

• The products referred to in this manual conform to the European Community Directives and are there-

fore marked with .

• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.

Never make any modiﬁcations on the unit not described in this instruction manual, otherwise you will

risk an electric shock.

• Connection must be made to a power supply system ﬁtted with eﬃcient earthing (Class I appliance ac-

cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units

from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• The connection to the main network of electric distribution must be carried out by a qualiﬁed electrical

installer. Check that the main frequency and voltage correspond to those for which the unit is designed

as given on the electrical data label.

• This unit is not for home use, only professional applications.

• Never use the ﬁxture under the following conditions:

- in places wet;

- in places subject to vibrations or bumps;

- in places with a temperature of over 45 °C.

• Make certain that no inﬂammable liquids, water or metal objects enter the ﬁxture.

• Do not dismantle or modify the ﬁxture.

• All work must always be carried out by qualiﬁed technical personnel. Contact the nearest sales point for

an inspection or contact the manufacturer directly.

• If the unit is to be put out of operation deﬁnitively, take it to a local recycling

plant for a disposal which is not harmful to the environment.

Warnings and installation precautions

• If this device will be operated in any way diﬀerent to the one described in this manual, it may suﬀer

damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like

short circuit, burns, electric shock, etc.

• Before starting any maintenance work or cleaning the projector, cut oﬀ power from the main supply.

• Always additionally secure the projector with the safety rope. When carrying out any work, always com-

ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country

in which the ﬁxture’s being used.

• Install the ﬁxture in a well ventilated place.

• Keep any inﬂammable material at a safe distance from the ﬁxture.

• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent

that their eﬀectiveness is impaired.

• The lamp (LED) shall be changed if it has become damaged or thermally deformed.

• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ﬂashing light, may

trigger epileptic seizures in photosensitive persons or persons with epilepsy.

• Do not touch the product’s housing when operating because it may be very hot.

• This product was designed and built strictly for the use indicated in this documentation. Any other use,

not expressly indicated here, could compromise the good condition/operation of the product and/or

be a source of danger.

• We decline any liability deriving from improper use of the product.

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

ECLIPSEHD2

- 1 - INTRODUCTION

1.1 DESCRIPTION

ECLIPSEHD2 updates ECLIPSEHD ranges with extra brightness and higher CRI / R9 / TLCI.

The ﬁxture is a proper LED replacement for the traditional 750 W Tungsten ellipsoidal luminaire. The opti-

cal system harnesses the power of a 230 W COB LED to create an even beam with clean shutter cuts and

beautiful sharp or soft edge gobo focusing.

Featuring HD dimming and available in a 3.300 K or 5.400 K, the ECLIPSEHD2 delivers the performance and

quality of output demanded from this level of the luminaire.

1.2 TECHNICAL SPECIFICATIONS

LIGHT SOURCE

• Source: 230W high-power white LED

• CT: (TU) 3.300 K - (DY) 5.400K

• CRI: (TU) 97 - (DY) 95,5

• Luminous ﬂux: (TU) 5°: 8’837 lm - 10°: 9’420 lm - 14°: 11’328 lm -19°: 10’989 lm - 26°: 13’504 lm - 36°:

13’548 lm - 50°: 12’020 lm - (DY) 5°: 7’537 lm - 10°: 9’832 lm - 14°: 13’787 lm -19°: 11’694 lm - 26°: 14’466

lm - 36°:14’454 lm - 50°: 12’267lm

• Lux: (TU) 5° 106’166 lx - 10° 58’800 lx - 14° 30’978 lx - 19° 28’800 lx - 26° 22’300 lx - 36° 12’600 lx - 50°

4’150lx @3 m

• Lux: (DY) 5° 45’080 lx - 10° 25’676 lx - 14° 13’778 lx - 19° 33’000 lx - 26° 24’300 lx - 36° 13’900 lx - 50°

6’000lx @3 m

• Source life expectancy: > 50.000 h

• Other: TLCI (TU) 19°: 90,5 - 26°: 89,7 - 36°: 92 - 50°: 90

OPTICS

• Beam angle: optional 5° / 10° / 14° / 19° / 26° / 36° / 50° / Z 15-30° / Z 25-50°

• Lens type: high-quality glass lens optics

• Focus: manual

COLOUR SYSTEM

• Colour mixing: static white

DYNAMIC EFFECTS

• Gobo size: B, outer: 86 mm - image: 64,5 mm - thickness: 1,1 mm

• Static colour mode: selection of static colour

• Manual colour mode:

• Auto mode: built-in programs with execution speed adjustment

BODY

• Body: sturdy die-cast aluminium body conceived for long-time durability

• Body colour: black

CONTROL

• Protocols: DMX512, RDM

• DMX channels: 1 / 2 / 5channel

• RDM: RDM ready for ﬁxture remote monitor and settings

• Display: black OLED high resolution display

ECLIPSEHD2

• Firmware upgrade: yes, via USB - DMX interface (UPBOX1) not included

• Master/Slave: for synchronized operation of more units linked in a chain

ELECTRONICS

• Dimmer: linear 0 ~ 100% electronic dimmer

• Dimmer curves: 4 diﬀerent dimming curves available

• Strobe / shutter: 1 - 30 Hz, electronic

• Operating temperature: -10° ~ +45°

• Flicker: ﬂicker free operation

• Selectable PWM: 600 ~ 25.000 Hz

ELECTRICAL

• Power supply: 100-240 V – 50/60 Hz

• Power consumption (at 230 V): 229 W

• Power consumption (at 120 V): 226 W

• Output (at 230 V): 15 units on a single power line

• Output (at 120 V): 8 units on a single power line

PHYSICAL

• Cooling: combination of heat pipe cooling system and low noise fan

• Sospension and ﬁxing: hanging bracket suitable for safe hanging and positioning

• Signal connection: Amphenol XLR 5p IN/OUT connectors

• Power connection: Neutrik powerCON IN/OUT connectors

• IP rating: 20

• Dimensions (WxHxD): 342x506x530 mm

• Weight: 7,11 kg

Technical drawing Fig.1

526

342

528

ECLIPSEHD2

1.3 CONFIGURATIONS

Conﬁguration

1 Reﬂector Housing

Middle part, compatible with

5 °, 10 °, 14 °, 19°, 26°, 36°,

50° optics

ECLIPSELB05

Optics for ECLIPSE proﬁler,

5° beam

ECLIPSELB10

Optics for ECLIPSE proﬁler,

10° beam

ECLIPSELB14

Optics for ECLIPSE proﬁler,

14° beam

ECLIPSELB19

Optics for ECLIPSE proﬁler,

19° beam

ECLIPSELB26

Optics for ECLIPSE proﬁler,

26° beam

ECLIPSELB36

Optics for ECLIPSE proﬁler,

36° beam

ECLIPSELB50

Optics for ECLIPSE proﬁler,

50° beam

ECLIPSEHD2

Fig.2

Rear panel

1.4 OPERATING ELEMENTS AND CONNECTIONS

1. MOUNTING BRACKET

2. LOCKING KNOB for the mounting bracket

3. HANDLE

4. ECLIPSEHD2

5. SAFETY EYE to attach safety cable.

6. SHUTTER

7. ECLIPSEMP - Aluminium middle part

8. OPTIC

9. FILTER FRAME

10. FUSE OLDER in the event of breakage, always

replace the fuse with the same type and

rating (T3.15A).

11. CONTROL PANEL with display and 4 button

used to access the control panel functions

and manage them.

12. POWER IN (PowerCON IN): for connection to a

socket (100-240V~/50-60Hz) via the supplied

mains cable.

13. POWER OUT (PowerCON OUT): connect to

supply power to the next unit.

14. DMX OUT (5-pole XLR):

1 = ground, 2 = DMX-, 3 = DMX+, 4 N/C, 5 N/C

15. DMX IN (5-pole XLR):

1 = ground, 2 = DMX-, 3 = DMX+, 4 N/C, 5 N/C

HD2

ECLIPSEHD2

CLAMP

SAFETY

CABLE

- 2 - INSTALLATION

2.1 MOUNTING

ECLIPSEHD2 may be set up on a solid and even surface. The unit can also be mounted upside down to a

cross arm. For ﬁxing, stable mounting clips are required. The mounting place must be of suﬃcient stability

and be able to support a weight of 10 times of the unit’s weight.

When carrying out any installation, always comply scrupulously with all the regulations (particularly re-

garding safety) currently in force in the country in which the ﬁxture’s being used.

• Install the projector at a suitable location by means of the mounting bracket (1).

• Always additionally secure the projector with the safety rope from falling down. For this purpose, fas-

ten the safety rope at a suitable position so that the maximum fall of the projector will be 20 cm.

• Adjust the projector and use the knob (2) to slightly release or tighten the locking mechanism of the

bracket if is necessary.

Fig.3

ECLIPSEHD2

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

Connect the supplied main cable to a socket (100-240 VAC-50/60 Hz). Then the unit is ready for operation

and can be operated via a DMX controller or it independently performs its show program in succession.

To switch oﬀ, disconnect the mains plug from the socket. For a more convenient operation it is recom-

mended to connect the unit to a socket which can be switched on and oﬀ via a light switch.

3.2 BASIC

Access control panel functions using the four panel buttons located directly underneath the OLED Display

(ﬁg.4).

UP DOWN ENTER

Used to access the menu or

to return a previous menu

option

Navigates downwards through

the menu list and increases

the numeric value when in a

function

Navigates upwards through

the menu list and decreases

the numeric value when in

a function

Used to select and store the

current menu or confirm the

current function value or

option within a menu

Fig.4 - Functions of the buttons

MENU UP

DOWNENTER

ECLIPSEHD2

3.3 MENU STRUCTURE

MENU Remark

1 DMX Address

Value (001-512) Default: 001

2 DMX Channel

Theater

1 Ch Default: 5 CH

2 Ch

5 Ch

3 Static

Dimmer

Value (0-255)

Default: Dimmer=255,

Strobe=0

Strobe

Value (0-255)

4 Auto Show

Auto 1

Value (1-100)

Default: Auto 4; Speed:100

Auto 2

Value (1-100)

Auto 3

Value (1-100)

Auto 4

Value (1-100)

5 Master/Slave

Master Default: Slave

Slave

6 Dimmer Mode

Off Default: Off

Dimmer 1

Dimmer 2

Dimmer 3

7 LED Frequency

600 Hz Default: 1200 kHz

1200 Hz

2000 Hz

4000 Hz

25 kHz

8 Fan Mode

Auto Default: Auto

High

9 Back Light

On Default: On

10 s

20s

30 s

10 Information

Fixture Hours < 9999H >

Version < V1.0 >

UID: 15D002050001

ECLIPSEHD2

3.4 DMX MODE

• Press the button MENU so many times until the display shows DMX ADDRESS, and press the button ENTER

to conﬁrm.

• Press UP/DOWN button to select the desired value (001-512). Press and hold to scroll quickly.

• Press ENTER button to store.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

To able to operate the ECLIPSEHD2 with a light controller, adjust the DMX start address for the first a

DMX channel. If e. g. address 33 on the controller is provided for controlling the function of the first DMX

channel, adjust the start address 33 on the ECLIPSEHD2. The other functions of the light effect panel are

then automatically assigned to the following addresses.

An example with the start address 33 is shown below:

3.5 DMX CONFIGURATION

ECLIPSEHD2 is equipped with diﬀerent DMX conﬁguration.

• Press the button MENU so many times until shows DMX CHANNEL, and press the button ENTER to conﬁrm.

• Select the desired DMX conﬁguration (1CH - 2CH - 5CH) through the buttons UP/DOWN.

The tables on page 14 indicate the operating mode and DMX value. The ECLIPSEHD2 is equipped with

5-pole XLR connections.

3.6 LINKING

Several units may be interconnected in order to control all further slave units to the same eﬀect of the

master unit.

1. Connect the DMX OUT of the master unit via 5-pole XLR cable to the DMX IN of the ﬁrst slave unit.

2. Connect the DMX OUT of the ﬁrst slave unit to the DMX IN of the second slave unit, etc. until all units

are connected in a chain.

DMX Address: 48DMX Address: 38DMX Address: 33 DMX Address: 43

Fig.5 - Example 5 DMX channels configuration

DMX512 Controller

Number of

DMX channels

Start address

(example)

DMX Address

occupied

Next possible start

address for unit No. 1

Next possible start

address for unit No. 2

Next possible start

address for unit No. 3

1 33 33 34 35 36

2 33 33-34 35 37 39

5 33 33-37 38 43 48

. . . . . . . . . . . .

ECLIPSEHD2

3.7 STATIC MODE

This ﬁxture has the ability to accept custom static color settings. Access these chases via the control panel

on the back of the ﬁxture.

• To enable the static mode, press MENU repeatedly until STATIC shows on the display.

• Through the button UP/DOWN select DIMMER or STROBE then press the button ENTER.

• Set the value (000 - 255), through the buttons UP/DOWN.

• Press the button ENTER to conﬁrm.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.8 AUTO SHOW MODE

If no DMX control signal is present at the DMX INPUT, the unit independently runs through its show pro-

gramme provided that the blackout mode is switched oﬀ:

• Press the button MENU so many times until the display shows AUTO, then press the button ENTER.

• Press the button UP/DOWN to switch between the show AUTO 1 - AUTO 4. The unit will operate in show

• mode.

• Using the button UP/DOWN to select the desired run speed slow-fast (0-100)

• Press the button ENTER to save the setting.

• IMPORTANT: Programs AUTO 1 - AUTO 4 are fully pre-programmed and will not be altered by changes.

3.9 MASTER/SLAVE MODE

This mode will allow you to link up the units together without a controller. Choose a unit to function as the

Master. The unit must be the ﬁrst unit in line; other units will work as slave with the same eﬀect.

• Press the button MENU so many times until the display shows MASTER/SLAVE and press the button ENTER.

• Press UP/DOWN to set the unit as master or slave (MASTER, SLAVE).

• Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of the

units. For longer cable runs we suggest a terminator at the last ﬁxture (see page 13).

3.10 DIMMER MODE

Enter in Dimmer mode to select speciﬁc dimming curve, press the button MENU so many times until

shows DIM MODE, and press the button ENTER to conﬁrm.

• Press the button UP/DOWN to select OFF - DIM1 - DIM2 - DIM3.

• Press ENTER button to store.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.11 LED FREQUENCY

To adjust the frequency of the LEDs, press the MENU button repeatedly until the display shows LED Fre-

quency, and then press the ENTER button.

• Select the frequency (600Hz - 1200Hz - 2000Hz - 4000Hz - 25kHz) using the UP/DOWN buttons.

• To conﬁrm, press the ENTER key.

• Press the MENU button to go back or wait a few seconds to exit the setup menu.

3.12 FAN MODE

To set the Fan Mode press the button MENU so many times until shows FAN MODE, and press the button

ENTER to conﬁrm.

• Press the button UP/DOWN to select AUTO - HIGH.

ECLIPSEHD2

• Press ENTER button to conﬁrm the selection.

• Press the MENU button to go back or to meet the waiting time to exit from the setup menu automati-

cally.

3.13 BACK LIGHT

To activate Backlight display press the button MENU so many times until shows BACK LIGHT, and press the

button ENTER to conﬁrm.

• Press the button UP/DOWN to select ON - 10s - 20s - 30s.

• Press ENTER button to conﬁrm the selection.

• Press the MENU button to go back or to meet the waiting time to exit from the setup menu automati-

cally.

3.14 INFORMATION

To view all the information on the device, proceed as follows:

• Press the MENU to access the main menu, then press the UP/DOWN button to select INFORMATION, then

use the ENTER button to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, then select one of the following information

and press the ENTER button to display it

- FixHours - Through the Time Information function you can display the operating time of the

projector.

- Version - Through Software Version function you can display the currently installed software

version.

ECLIPSEHD2

Fig.6

Fig.7

3.15 CONNECTION OF THE DMX LINE

DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120Ω imped-

ance and low capacity.

The following diagram shows the connection mode:

ATTENTION

The screened parts of the cable (sleeve) must never be connected to the system’s earth, as this would

cause faulty ﬁxture and controller operation.

Over long runs can be necessary to insert a DMX level matching ampliﬁer.

For those connections the use of balanced microphone cable is not recommended because it cannot

transmit control DMX data reliably.

• Connect the controller DMX input to the DMX output of the ﬁrst unit.

• Connect the DMX output to the DMX input of the following unit. Connect again the output to the input

of the following unit until all the units are connected in chain.

• When the signal cable has to run longer distance is recommended to insert a DMX termination on the

last unit.

3.16 CONSTRUCTION OF THE DMX TERMINATION

The termination avoids the risk of DMX 512 signals being reﬂected back along the cable when they reach-

es the end of the line: under certain conditions and with certain cable lengths, this could cause them to

cancel the original signals.

The termination is prepared by soldering a 120Ω 1/4 W resistor between pins 2 and 3 of the 5-pin male XLR

connector, as shown in ﬁgure.

DMX - OUTPUT

XLR socket

DMX - INPUT

XLR plug

Pin1 : GND - Shield

Pin2 : - Negative

Pin3 : + Positive

Pin4 : N/C

Pin5 : N/C

Example:

3 pin XLR connector

ECLIPSEHD2

3.17 DMX CONTROL

1 CHANNEL

MODE

FUNCTION DMX

Value

1 Ch

DIMMER

0~100% 000 - 255

2 CHANNELS

MODE

FUNCTION DMX

Value

2 Ch

DIMMER

0~100% 000 - 255

STROBE

NO Function

Strobe Slow to Fast

000 - 010

011 - 255

5 CHANNELS

MODE

FUNCTION DMX

Value

5 Ch

DIMMER

0~100% 000 - 255

STROBE

NO Function

Strobe Slow to Fast

000 - 010

011 - 255

Auto programs

NO Function

Auto Program 1

Auto Program 2

Auto Program 3

Auto Program 4

000 - 010

011 - 070

071 - 130

131 - 190

191 - 255

Auto Speed

Speed slow to fast 000 - 255

Dimmer Speed Mode

Prese dimmer speed from display menu

Dimmer speed mode off

Dimmer speed mode 1 (fast speed)

Dimmer speed mode 2 (middle speed)

Dimmer speed mode 3 (slow speed)

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

ECLIPSEHD2

- 4 - MAINTENANCE

4.1 MAINTENANCE AND CLEANING THE UNIT

• Make sure the area below the installation place is free from unwanted persons during setup.

• Switch oﬀ the unit, unplug the main cable and wait until the unit has cooled down.

• All screws used for installing the device and any of its parts should be tightly fastened and should not

be corroded.

• Housings, ﬁxations and installation spots (ceiling, trusses, suspensions) should be totally free from any

deformation.

• The main cables must be in impeccable condition and should be replaced immediately even when a

small problem is detected.

• It is recommended to clean the front at regular intervals, from impurities caused by dust, smoke, or

other particles to ensure that the light is radiated at maximum brightness. For cleaning, disconnect the

main plug from the socket. Use a soft, clean cloth moistened with a mild detergent. Then carefully wipe

the part dry. For cleaning other housing parts use only a soft, clean cloth. Never use a liquid, it might

penetrate the unit and cause damage to it.

4.2 FUSE REPLACEMENT

1. Remove the safety cap by a screwdriver.

2. Replace the blown fuse with a fuse of the exact same type and rating.

3. Install the safety cap, and reconnect power.

4.3 TROUBLESHOOTING

Fig.8

Problems Possible causes Checks and remedies

Fixture does not light up

• No mains supply

• Dimmer fader set to 0

• All color faders set to 0

• Faulty LED

• Faulty LED board

• Check the power supply voltage

• Increase the value of the dimmer channels

• Increase the value of the color channels

• Replace the LED board

General low light intensity

• Dirty lens assembly

• Misaligned lens assembly

• Clean the fixture regularly

• Install lens assembly properly

Fixture does not power up

• No power

• Loose or damaged power cord

• Faulty internal power supply

• Check for power on power outlet

• Check power cord

• Replace internal power supply

Fixture does not respond to DMX

• Wrong DMX addressing

• Damaged DMX cables

• Bouncing signals

• Check control panel and unit addressing

• Check DMX cables

• Install terminator as suggested

Contact an authorized service center in case of technical problems or not reported in the table can not be

resolved by the procedure given in the table.

REV.02-11/19

Music & Lights S.r.l. si riserva ogni diritto di elaborazione in qualsiasi forma delle presenti istruzioni per l’uso.

La riproduzione - anche parziale - per propri scopi commerciali è vietata.

Al fine di migliorare la qualità dei prodotti, la Music&Lights S.r.l. si riserva la facoltà di modificare, in

qualunque momento e senza preavviso, le specifiche menzionate nel presente manuale di istruzioni.

Tutte le revisioni e gli aggiornamenti sono disponibili nella sezione 'Manuali' sul sito www.musiclights.it

ECLIPSEHD2

• ECLIPSEHD2

• Staffa di fissaggio

• Cavo di alimentazione

• Manuale utente

Contenuto dell'imballo:

INDICE

Sicurezza

Avvertenze generali

Attenzioni e precauzioni per l’installazione

1 Introduzione

1. 1 Descrizione

1. 2 Specifiche tecniche

1. 4 Configurazioni

1. 3 Elementi di comando e di collegamento

2 Installazione

2. 1 Montaggio

3 Funzioni e impostazioni

3. 1 Funzionamento

3. 2 Impostazione base

3. 3 Struttura menu

3. 4 Modalità DMX

3. 5 Configurazione canali DMX

3. 6 Collegamento

3. 7 Modalità Static

3. 8 Modalità Auto Show

3. 9 Modalità Master/Slave

3. 10 Modalità Dimmer

3. 11 Frequenza LED

3. 12 Fan Mode

3. 13 Back Light

3. 14 Informazioni sul dispositivo

3.15 Collegamenti della linea DMX

3.16 Costruzione del terminatore DMX

3.17 Canali DMX

4 Manutenzione

4. 1 Manutenzione e pulizia del sistema ottico

4. 2 Sostituzione fusibile

4. 3 Risoluzione dei problemi

ECLIPSEHD2

ATTENZIONE! Prima di effettuare qualsiasi operazione con l’unità, leggere con attenzione

questo manuale e conservarlo accuratamente per riferimenti futuri. Contiene informazioni

importanti riguardo l’installazione, l’uso e la manutenzione dell’unità.

SICUREZZA

Avvertenze generali

• I prodotti a cui questo manuale si riferisce sono conformi alle Direttive della Comunità Europea e per-

tanto recano la sigla .

• Il dispositivo funziona con pericolosa tensione di rete 230V~. Non intervenire mai al suo interno al di

fuori delle operazioni descritte nel presente manuale; esiste il pericolo di una scarica elettrica.

• È obbligatorio eﬀettuare il collegamento ad un impianto di alimentazione dotato di un’eﬃciente messa

a terra (apparecchio di Classe I secondo norma EN 60598-1). Si raccomanda, inoltre, di proteggere le

linee di alimentazione delle unità dai contatti indiretti e/o cortocircuiti verso massa tramite l’uso di

interruttori diﬀerenziali opportunamente dimensionati.

• Le operazioni di collegamento alla rete di distribuzione dell’energia elettrica devono essere eﬀettuate

da un installatore elettrico qualiﬁcato. Veriﬁcare che frequenza e tensione della rete corrispondono alla

frequenza ed alla tensione per cui l’unità è predisposta, indicate sulla targhetta dei dati elettrici.

• L’unità non per uso domestico, solo per uso professionale.

• Evitare di utilizzare l’unità:

- in luoghi soggetti ad umidità;

- in luoghi soggetti a vibrazioni, o a possibili urti;

- in luoghi a temperatura superiore ai 45°C.

• Evitare che nell’unità penetrino liquidi inﬁammabili, acqua o oggetti metallici.

• Non smontare e non apportare modiﬁche all’unità.

• Tutti gli interventi devono essere sempre e solo eﬀettuati da personale tecnico qualiﬁcato. Rivolgersi al

più vicino centro di assistenza tecnica autorizzato.

• Se si desidera eliminare il dispositivo deﬁnitivamente, consegnarlo

per lo smaltimento ad un’istituzione locale per il riciclaggio.

Attenzioni e precauzioni per l’installazione

• Se il dispositivo dovesse trovarsi ad operare in condizioni diﬀerenti da quelle descritte nel presente

manuale, potrebbero veriﬁcarsi dei danni; in tal caso la garanzia verrebbe a decadere. Inoltre, ogni altra

operazione potrebbe provocare cortocircuiti, incendi, scosse elettriche, rotture etc.

• Prima di iniziare qualsiasi operazione di manutenzione o pulizia sull’unità togliere la tensione dalla rete

di alimentazione.

• È assolutamente necessario proteggere l’unità per mezzo di una fune di sicurezza. Nell’eseguire qual-

siasi intervento attenersi scrupolosamente a tutte le normative (in materia di sicurezza) vigenti nel

paese di utilizzo.

• Installare l’unità in un luogo ben ventilato.

• Mantenere i materiali inﬁammabili ad una distanza di sicurezza dall’unità.

• I ﬁltri, le lenti o gli schermi ultravioletti se danneggiati possono limitare la loro eﬃcienza.

• I LED devono essere sostituiti se danneggiati o termicamente deformati.

• Non guardare direttamente il fascio luminoso. Tenete presente che i veloci cambi di luce possono pro-

vocare attacchi d’epilessia presso persone fotosensibili o epilettiche.

• Non toccare l’alloggiamento del prodotto quando è in funzione perché potrebbe essere molto caldo.

• Questo prodotto è stato progettato e costruito esclusivamente per l’utilizzo indicato in questa docu-

mentazione. Qualsiasi altro utilizzo non espressamente indicato potrebbe pregiudicare la funzionalità

del prodotto e/o rappresentare fonte di pericolo.

• Si declina qualsiasi responsabilità derivata dall’uso improprio del prodotto.

La pagina sta caricando ...

ProLights 230 W high power LED ellipsoidal profile Manuale utente

Marca: ProLights

Modello: 230 W high power LED ellipsoidal profile

Categoria: Stroboscopi

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: ProLights 230 W high power LED ellipsoidal profile User manual

ProLights 230 W high power LED ellipsoidal profile Manuale utente

ProLights 230 W high power LED ellipsoidal profile Manuale utente

in altre lingue

Documenti correlati