ProLights IP65 160 W zoomable LED ellipsoidal Manuale utente

Marca: ProLights

Modello: IP65 160 W zoomable LED ellipsoidal

Categoria: Stroboscopi

Tipo: Manuale utente

USER MANUAL

MANUALE UTENTE

ECLIPSEJZIP

EN - IT

LED PROFILER

ECLIPSEJZIP

ECLIPSEJZIPLZ2550

ECLIPSEJZIPLZ1530

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the

characteristics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

REV.01-04/19

ECLIPSEJZIP

Packing content

• ECLIPSEJZIP

• Power cable

• User manual

TABLE OF CONTENTS

Safety

General instructions

Warnings and installation precautions

1 Introduction

1. 1 Description

1. 2 Technical specications

1. 3 Operating elements and connections

2 Installation

2. 1 Mounting

3 Functions and settings

3. 1 Operation

3. 2 Basic

3. 3 Menu structure

3. 4 DMX mode

3. 5 DMX addressing

3. 6 DMX linking

3. 7 Wireless settings

3. 8 Screen

3. 9 Advanced

3. 10 Information

3. 11 Master / Slave

3. 12 Eects mode

3. 13 Static mode

3. 14 DMX control

3. 15 Connection of the DMX line

3. 16 Construction of the DMX termination

4 Maintenance

4. 1 Maintenance and cleaning the unit

4. 2 Trouble shooting

ECLIPSEJZIP

SAFETY

General instruction

• The products referred to in this manual conform to the European Community Directives and are there-

fore marked with .

• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.

Never make any modications on the unit not described in this instruction manual, otherwise you will

risk an electric shock.

• Connection must be made to a power supply system tted with ecient earthing (Class I appliance ac-

cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units

from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• The connection to the main network of electric distribution must be carried out by a qualied electrical

installer. Check that the main frequency and voltage correspond to those for which the unit is designed

as given on the electrical data label.

• This unit is not for home use, only professional applications.

• Never use the xture under the following conditions:

- in places subject to vibrations or bumps;

- in places with a temperature of over 45 °C.

• Make certain that no inammable liquids, water or metal objects enter the xture.

• Do not dismantle or modify the xture.

• All work must always be carried out by qualied technical personnel. Contact the nearest sales point for

an inspection or contact the manufacturer directly.

• If the unit is to be put out of operation denitively, take it to a local recycling

plant for a disposal which is not harmful to the environment.

Warnings and installation precautions

• If this device will be operated in any way dierent to the one described in this manual, it may suer

damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like

short circuit, burns, electric shock, etc.

• Before starting any maintenance work or cleaning the projector, cut o power from the main supply.

• Always additionally secure the projector with the safety rope. When carrying out any work, always com-

ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country

in which the xture’s being used.

• Install the xture in a well ventilated place.

• Keep any inammable material at a safe distance from the xture.

• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent

that their eectiveness is impaired.

• The lamp (LED) shall be changed if it has become damaged or thermally deformed.

• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ashing light, may

trigger epileptic seizures in photosensitive persons or persons with epilepsy.

• Do not touch the product’s housing when operating because it may be very hot.

• This product was designed and built strictly for the use indicated in this documentation. Any other use,

not expressly indicated here, could compromise the good condition/operation of the product and/or

be a source of danger.

• We decline any liability deriving from improper use of the product.

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

ECLIPSEJZIP

- 1 - INTRODUCTION

1.1 DESCRIPTION

ECLIPSEJZIP is an IP rated zoomable ellipsoidal designed for exterior application. ECLIPSEJZIP reaches an

exceedingly high lumen output of nearly 6’000 lumens, and all in a compact size allowing for use on any

outdoor show or for logo and texture projection over buildings. ECLIPSEJZIP can use two dierent manual

zoom lenses (optional) being 15°-30° or 25°-50° and it can be mounted at any distance from the projection

surface.

1.2 TECHNICAL SPECIFICATIONS

LIGHT SOURCE

• Source: 160W warm white LED

• CT: 3100K

• CRI: >81

• Luminous ux: (50°) 5274 lm - (25°) 5770 lm; (30°) 4200 lm - (15°) 5012lm

• Lux: (50°) 2040 lux - (25°) 5160 lux; (30°) 3710 lux - (15°) 12900lux @3m

• Lux: (50°) 734 lux - (25°) 1857 lux; (30°) 1336 lux - (15°) 4644lux @5m

• Source life expectancy: >50.000 h

OPTICS

• Beam angle: (optional) manual zoom lens 15°-30° or (optional) manual zoom lens 25°-50°

• Lens diameter: 87mm

• Lens type: high-quality glass lens optics

• Focus: manual

COLOUR SYSTEM

• Macros: several pre-build macros with adjustable speed

DYNAMIC EFFECTS

• Gobo size: M: Ø 66mm, img Ø 48 mm, 2 mm

• Static colour mode: selection of static dimmer

• Manual colour mode: manual adjustment of dimmer and strobe

• Auto mode: built-in programs with execution speed adjustment

BODY

• Hardware on-board: on board mechanics for rigging to the ceiling

• Body: sturdy die-cast aluminium body conceived for long-time durability

• Body colour: black

CONTROL

• Protocols: DMX512, W-DMX

• DMX channels: 1 / 3channel

• W-DMX: included, wireless solution receiver

• RDM: RDM ready for xture remote monitor and settings

• Display: black OLED high resolution display

• Firmware upgrade: yes, via USB-DMX interface (UPBOX1) not included

• Master/Slave: for synchronized operation of more units linked in a chain

• Other: 16bit control of dimmer

ECLIPSEJZIP

ECLIPSEJZIPLZ2550 ECLIPSEJZIPLZ1530

310 262

310

310 344

Fig.1 - Technical drawings

275275

440

ELECTRONICS

• Dimmer: linear 0~100% electronic dimmer

• Dimmer curves: 4 dierent dimming curves available

• Strobe / shutter: 1 - 30 Hz, electronic

• Operating temperature: -20° ~ +45°

• Flicker: icker free operation

• Selectable PWM: 600~25K Hz

ELECTRICAL

• Power consumption: 136 W

• Power supply: 100-240V – 50/60Hz

• Power consumption (at 230V): 136W

• Power consumption (at 120V): 138.6W

• Power factor: pF 0.98 @ 120V - pF 0.97 @ 230V

PHYSICAL

• Cooling: forced air with low noise fan

• Sospension and xing: hanging bracket suitable for safe hanging and positioning

• Signal connection: Seetronic XLR 5p IN/OUT connectors

• Power connection: Seetronic powerCON waterproof IN/OUT connectors

• IP rating: 65 for temporary outdoor application, not for xed installation

• Dimensions with ECLIPSEJZIPLZ2550 (WxHxD): 537x310x489mm

• Dimensions with ECLIPSEJZIPLZ1530 (WxHxD): 619x310x489mm

• Weight: 7.9kg

ECLIPSEJZIP

9 10 11 12

Rear panel

1.3 OPERATING ELEMENTS AND CONNECTIONS

Fig.2

1. MOUNTING BRACKET

2. LOCKING KNOB for the mounting bracket

3. SAFETY EYE to attach safety cable

4. SHUTTER (x4)

5. OPTICS

6. FOCUS KNOB

7. GEL FRAME HOLDER

8. CONTROL PANEL with display and 4 button

used to access the control panel functions

and manage them.

9. POWER IN (PowerCON TRUE IN): for

connection to a socket 100-240V~/50-60Hz)

via the supplied mains cable.

10. DMX IN (5-pole XLR): 1 = ground, 2 = DMX-, 3

= DMX+, 4 N/C, 5 N/C.

11. DMX OUT (5-pole XLR): 1 = ground, 2 = DMX-,

3 = DMX+, 4 N/C, 5 N/C.

12. POWER OUT (PowerCON TRUE OUT): power

output for connection of multiple units in

series.

ECLIPSEJZIP

- 2 - INSTALLATION

2.1 MOUNTING

ECLIPSEJZIP may be set up on a solid and even surface. The unit can also be mounted upside down to a

cross arm. For xing, stable mounting clips are required. The mounting place must be of sucient stability

and be able to support a weight of 10 times of the unit’s weight.

When carrying out any installation, always comply scrupulously with all the regulations (particularly re-

garding safety) currently in force in the country in which the xture’s being used.

• Install the projector at a suitable location by means of the mounting bracket (1).

• Always additionally secure the projector with the safety rope from falling down. For this purpose, fas-

ten the safety rope at a suitable position so that the maximum fall of the projector will be 20 cm.

• Adjust the projector and use the knob (2) to slightly release or tighten the locking mechanism of the

bracket if is necessary.

Fig.3

CLAMP

SAFETY

CABLE

ECLIPSEJZIP

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

Connect the supplied main cable to a socket (100-240 VAC-50/60 Hz). Then the unit is ready for operation

and can be operated via a DMX controller. To switch o, disconnect the mains plug from the socket. For a

more convenient operation it is recommended to connect the unit to a socket which can be switched on

and o via a light switch.

3.2 BASIC

Access control panel functions using the four panel buttons located directly underneath the OLED Display

(g.4).

MODE UP DOWN ENTER

Used to access the menu or

to return a previous menu

option

Navigates downwards through

the menu list and increases

the numeric value when in a

function

Navigates upwards through

the menu list and decreases

the numeric value when in

a function

Used to select and store the

current menu or conrm the

current function value or

option within a menu

Fig.4 - Functions of the buttons

MODE UP

DOWNENTER

ECLIPSEJZIP

3.3 MENU STRUCTURE

1 CONNECT

DMX Address

Value (1-512)

DMX Mode

1Ch

3Ch

Wireless Setting

Receive O/On

O

Receive Reset

Yes

Wireless To DMX

Yes

2 SETUP

Screen

Back Light

10s

20s

30s

Flip Display

Yes

Key Lock

Yes

3 ADVANCED

Dimmer Mode

O

Dimmer1

Dimmer2

Dimmer3

LED Frequency

600Hz

1200Hz

2000Hz

4000Hz

6000Hz

25kHZ

Fan Mode

Auto

Silent

Factory Reload

Yes

4 INFORMATION

Fixture Hours

<9999H>

Version

<V1.0>

UID

15D00227****

5 STAND ALONE

Master/Slave

Eects

Eect 1

Eect 2

Eect 3

Eect 4

<1-100>

Static

Dimmer

Strobe

<000-255>

ECLIPSEJZIP

. . . . . . . . . . . .

DMX512 Controller

DMX Address: 33 DMX Address: 42DMX Address: 36 DMX Address: 39

Fig.5 - Example 3 DMX channels conguration

Number of

DMX channels

Start address

(example)

DMX Address

occupied

Next possible start

address for unit No. 1

Next possible start

address for unit No. 2

Next possible start

address for unit No. 3

1 33 33 34 35 36

3 33 33-35 36 39 42

3.4 DMX MODE

• Press on MODE and select Connect and press on ENTER to conrm.

• Press on UP/DOWN to select DMX Mode, then choose the desired DMX mode: 1 Ch or 3Ch. Press on ENTER

to store.

• Press on MODE to go back or to meet the waiting time to exit the setup menu.

The tables on page 12 indicate the operating mode and DMX value.

3.5 DMX ADDRESSING

• Press on MODE and select Connect and press on ENTER to conrm.

• Press on UP/DOWN to select Dmx Address, then choose the desired DMX address: 001 - 512. Press and hold

to scroll quickly.

• Press on ENTER button to store.

• Press on MODE button to go back or to meet the waiting time to exit the setup menu.

To able to operate the ECLIPSEJZIP with a light controller, adjust the DMX start address for the rst a DMX

channel. If e. g. address 33 on the controller is provided for controlling the function of the rst DMX chan-

nel, adjust the start address 33 on the ECLIPSEJZIP. The other functions of the light eect panel are then

automatically assigned to the following addresses.

An example with the start address 33 is shown below:

ECLIPSEJZIP

3.6 LINKING

1. Connect the DMX OUT of the master unit via 5-pole XLR cable to the DMX IN of the rst slave unit.

2. Connect the DMX OUT of the rst slave unit to the DMX IN of the second slave unit, etc. until all units

are connected in a chain.

3.7 WIRELESS SETTINGS

• To enter the Wireless mode press on MODE and select Connect, then select Wireless Settung using ENTER.

• Select the Receive On/O function pressing on UP/DOWN, then press on ENTER.

• To activate the Receive function, pressing on UP/DOWN and select the On option.

• Press on ENTER to conrm the selection.

• Press on MODE to go back or wait a few seconds to exit the setup menu.

NOTE - Once you have performed these steps, you must synchronize with any WiFi unit with which you

want to communicate by pressing the sync button on it. At this point connect the DMX console to the

WiFi unit to open the communication with the ECLIPSEJZIP.

• To reset the unit, select the Receive Reset function pressing on UP/DOWN, select Connect, then select

Receive Reset and press on ENTER.

• To activate the mode use UP / DOWN and select the Yes option.

• Press the ENTER button to conrm the selection.

• Press on MODE button to go back or wait a few seconds to exit the setup menu.

• To activate the Wireless to DMX function, use UP / DOWN to press on ENTER until the display shows Con-

nect, then select Wireless to DMX, then press on ENTER.

• To activate the mode use the UP/DOWN buttons and select the Yes option.

• Press on ENTER to conrm the selection.

• Press on MODE to go back or wait a few seconds to exit the setup menu.

3.8 SCREEN

It is possible to modify the following parameters, related to the display, following the same procedure:

• Press on MODE to access the main menu.

• Press on UP/DOWN to scroll through the menu, select Set Up, then press on ENTER to access the next

menu.

• Press on UP/DOWN to select Screen and press on ENTER to proceed.

• Select the proposed option with the UP/DOWN button and press the ENTER button to conrm.

- Backlight - Auto O display backlight. This function allows you to switch o automatically the back-

lighting of the display after a certain time which can be set using the UP/DOWN. To have the display

always on select On or set a value between those shown (10s, 20s, 30s) to turn o the display once the

chosen time has elapsed, after exiting the menu.

- Flip Display - Display orientation. This feature allows you to rotate the display by 180 ° to get a better

view of the display when the unit is hanging upside down. Select Yes to activate the function or No

to deactivate.

- Key lock - With this function, you can lock the keys on the control panel to prevent, for example, tam-

pering with the settings. If this function is activated, the keys are locked automatically. To disable or

temporarily disable or disable the key lock function, press the keys in the following order to regain

access to the menu commands: UP, DOWN, UP, DOWN, ENTER. Select Yes to activate the function or

No to deactivate it.

• Press on ENTER to conrm the selection.

• Press on MODE repeatedly to exit the menu and to save the changes made.

ECLIPSEJZIP

3.9 ADVANCED

You can change the parameters for the device by following these steps:

• Press on MODE to enter the menu mode.

• Press on UP/DOWN to select Advanced. Press the button ENTER to conrm.

• Press on UP/DOWN to select the desired option and press on ENTER to conrm:

- Dimmer Mode - Adjusting the dimmer. Enter in Dimmer Mode to select specic dimming curve.

Particularly when set:

• O: The increase in light intensity is linear.

• Dimmer 1: dimmer curve with low fade.

• Dimmer 2: dimmer curve with medium fade.

• Dimmer 3: dimmer curve with high fade.

- LED Frequency - To adjust the frequency of the LEDs. Select the frequency 600 Hz - 25 KHz using the UP/

DOWN and press on ENTER to conrm the selection.

- Fan Mode - Fan speed. Select the desired fan speed Auto, On, Silent, through UP/ DOWN.

- Factory Reload - To reset the unit. Select Yes or No and select ENTER to conrm.

• Press repeatedly on MODE to return the menu mode.

3.10 INFORMATION

To view all the information on the device, proceed as follows:

• Press on MODE to access the main menu. Press on UP/DOWN to select Information, then press on ENTER

to access the next menu.

• Press on UP/DOWN to scroll through the menu, then select one of the following information and press

on ENTER to display it.- Fixture Time - Through the Fixture Time function, the operating time of the

projector can be shown on the display.

- Fixture Time - To view the operating time of the projector.

- Software Version - To view the rmware version will show on the display.

- UID - To view the identication ID for the RDM control.

• Press repeatedly on MODE to return the menu mode.

3.11 MASTER/SLAVE MODE

This mode will allow you to link up the units together without a controller. Choose a unit to function as the

Master. The unit must be the rst unit in line; other units will work as slave.

• Press on MODE button so many times until the display shows Stand Alone, then press on ENTER.

• Select Master/Slave, then press ENTER.

• Using UP/DOWN, select the desired mode and then press ENTER.

• Press on MODE to go back or to meet the waiting time to exit the setup menu

• Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of the

units. For longer cable runs we suggest a terminator at the last xture (see page 15).

• Set the slaves to the same DMX modes.

NOTE: the unit, set in Static or Eect mode, always appears to be Master.

3.12 EFFECTS MODE

This xture has a built-in automatic program. To access this, please see the below instructions:

• To enter the Eects mode, press MODE to access the menu, using UP/DOWN select Stand Alone, then

press ENTER to conrm.

• Use UP/DOWN to select the desired program Eect 1, Eect 2, Eect 3, Eect 4, then press ENTER to conrm.

• Set the value (1 - 100), through UP/DOWN, then press ENTER to conrm.

ECLIPSEJZIP

3.14 DMX CONTROL

1 CHANNEL

MODE

FUNCTION DMX

Value

1 Ch

DIMMER

0~100% 000 - 255

3 CHANNELS

MODE

FUNCTION DMX

Value

3 Ch

DIMMER

0~100% 000 - 255

STROBE

No Function

Strobe Slow to Fast

000 - 010

011 - 255

Dimmer Speed Mode

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode 1 (fast speed)

Dimmer speed mode 2 (middle speed)

Dimmer speed mode 3 (slow speed)

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

3.13 STATIC MODE

This xture has the ability to accept custom static color settings. Access these chases via the control panel

on the back of the xture.

• To enable the static mode, press MODE repeatedly until Stand Alone shows on the display.

• Set the strobo value Strobe (000 - 255), through the buttons UP/DOWN, then press ENTER to conrm.

• Set the dimmer value Dimmer (000 - 255), through the buttons UP/DOWN, then press ENTER to conrm.

ECLIPSEJZIP

Fig.6

Fig.7

3.15 CONNECTION OF THE DMX LINE

DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120Ω imped-

ance and low capacity.

The following diagram shows the connection mode:

ATTENTION

The screened parts of the cable (sleeve) must never be connected to the system’s earth, as this would

cause faulty xture and controller operation.

Over long runs can be necessary to insert a DMX level matching amplier.

For those connections the use of balanced microphone cable is not recommended because it cannot

transmit control DMX data reliably.

• Connect the controller DMX input to the DMX output of the rst unit.

• Connect the DMX output to the DMX input of the following unit. Connect again the output to the input

of the following unit until all the units are connected in chain.

• When the signal cable has to run longer distance is recommended to insert a DMX termination on the

last unit.

3.16 CONSTRUCTION OF THE DMX TERMINATION

The termination avoids the risk of DMX 512 signals being reected back along the cable when they reach-

es the end of the line: under certain conditions and with certain cable lengths, this could cause them to

cancel the original signals.

The termination is prepared by soldering a 120Ω 1/4 W resistor between pins 2 and 3 of the 5-pin male XLR

connector, as shown in gure.

DMX - OUTPUT

XLR socket

DMX - INPUT

XLR plug

Pin1 : GND - Shield

Pin2 : - Negative

Pin3 : + Positive

Pin4 : N/C

Pin5 : N/C

Example:

5 pin XLR connector

ECLIPSEJZIP

- 4 - MAINTENANCE

4.1 MAINTENANCE AND CLEANING THE UNIT

• Make sure the area below the installation place is free from unwanted persons during setup.

• Switch o the unit, unplug the main cable and wait until the unit has cooled down.

• All screws used for installing the device and any of its parts should be tightly fastened and should not

be corroded.

• Housings, xations and installation spots (ceiling, trusses, suspensions) should be totally free from any

deformation.

• The main cables must be in impeccable condition and should be replaced immediately even when a

small problem is detected.

• It is recommended to clean the front at regular intervals, from impurities caused by dust, smoke, or

other particles to ensure that the light is radiated at maximum brightness. For cleaning, disconnect the

main plug from the socket. Use a soft, clean cloth moistened with a mild detergent. Then carefully wipe

the part dry. For cleaning other housing parts use only a soft, clean cloth. Never use a liquid, it might

penetrate the unit and cause damage to it.

4.2 TROUBLESHOOTING

Problems Possible causes Checks and remedies

Fixture does not light up

• No mains supply

• Dimmer fader set to 0

• All color faders set to 0

• Faulty LED

• Faulty LED board

• Check the power supply voltage

• Increase the value of the dimmer channels

• Increase the value of the color channels

• Replace the LED board

General low light intensity

• Dirty lens assembly

• Misaligned lens assembly

• Clean the xture regularly

• Install lens assembly properly

Fixture does not power up

• No power

• Loose or damaged power cord

• Faulty internal power supply

• Check for power on power outlet

• Check power cord

• Replace internal power supply

Fixture does not respond to DMX

• Wrong DMX addressing

• Damaged DMX cables

• Bouncing signals

• Check control panel and unit addressing

• Check DMX cables

• Install terminator as suggested

Contact an authorized service center in case of technical problems or not reported in the table can not be

resolved by the procedure given in the table.

Music & Lights S.r.l. si riserva ogni diritto di elaborazione in qualsiasi forma delle presenti istruzioni per l’uso.

La riproduzione - anche parziale - per propri scopi commerciali è vietata.

Al ne di migliorare la qualità dei prodotti, la Music&Lights S.r.l. si riserva la facoltà di modicare, in

qualunque momento e senza preavviso, le speciche menzionate nel presente manuale di istruzioni.

Tutte le revisioni e gli aggiornamenti sono disponibili nella sezione 'Manuali' sul sito www.musiclights.it

REV.01-04/19

ECLIPSEJZIP

• ECLIPSEJZIP

• Cavo di alimentazione

• Manuale utente

Contenuto dell'imballo:

INDICE

Sicurezza

Avvertenze generali

Attenzioni e precauzioni per l’installazione

1 Introduzione

1. 1 Descrizione

1. 2 Speciche tecniche

1. 3 Elementi di comando e di collegamento

2 Installazione

2. 1 Montaggio

3 Funzioni e impostazioni

3. 1 Funzionamento

3. 2 Impostazione base

3. 3 Struttura menu

3. 4 Modalità DMX

3. 5 Indirizzamento DMX

3. 6 Collegamento

3. 7 Impostazioni Wireless

3. 8 Screen

3. 9 Advanced

3. 10 Informazioni sul dispositivo

3. 11 Master/Slave

3. 12 Modalità Eects

3. 13 Modalità Static

3. 14 Canali DMX

3. 15 Collegamenti della linea DMX

3. 16 Costruzione del terminatore DMX

4 Manutenzione

4. 1 Manutenzione e pulizia del sistema ottico

4. 2 Risoluzione dei problemi

ECLIPSEJZIP

ATTENZIONE! Prima di effettuare qualsiasi operazione con l’unità, leggere con attenzione

questo manuale e conservarlo accuratamente per riferimenti futuri. Contiene informazioni

importanti riguardo l’installazione, l’uso e la manutenzione dell’unità.

SICUREZZA

Avvertenze generali

• I prodotti a cui questo manuale si riferisce sono conformi alle Direttive della Comunità Europea e per-

tanto recano la sigla .

• Il dispositivo funziona con pericolosa tensione di rete 230V~. Non intervenire mai al suo interno al di

fuori delle operazioni descritte nel presente manuale; esiste il pericolo di una scarica elettrica.

• È obbligatorio eettuare il collegamento ad un impianto di alimentazione dotato di un’eciente messa

a terra (apparecchio di Classe I secondo norma EN 60598-1). Si raccomanda, inoltre, di proteggere le

linee di alimentazione delle unità dai contatti indiretti e/o cortocircuiti verso massa tramite l’uso di

interruttori dierenziali opportunamente dimensionati.

• Le operazioni di collegamento alla rete di distribuzione dell’energia elettrica devono essere eettuate

da un installatore elettrico qualicato. Vericare che frequenza e tensione della rete corrispondono alla

frequenza ed alla tensione per cui l’unità è predisposta, indicate sulla targhetta dei dati elettrici.

• L’unità non è per uso domestico, solo per uso professionale.

• Evitare di utilizzare l’unità:

- in luoghi soggetti a vibrazioni, o a possibili urti;

- in luoghi a temperatura superiore ai 45°C.

• Evitare che nell’unità penetrino liquidi inammabili, acqua o oggetti metallici.

• Non smontare e non apportare modiche all’unità.

• Tutti gli interventi devono essere sempre e solo eettuati da personale tecnico qualicato. Rivolgersi al

più vicino centro di assistenza tecnica autorizzato.

• Se si desidera eliminare il dispositivo denitivamente, consegnarlo

per lo smaltimento ad un’istituzione locale per il riciclaggio.

Attenzioni e precauzioni per l’installazione

• Se il dispositivo dovesse trovarsi ad operare in condizioni dierenti da quelle descritte nel presente

manuale, potrebbero vericarsi dei danni; in tal caso la garanzia verrebbe a decadere. Inoltre, ogni altra

operazione potrebbe provocare cortocircuiti, incendi, scosse elettriche, rotture etc.

• Prima di iniziare qualsiasi operazione di manutenzione o pulizia sull’unità togliere la tensione dalla rete

di alimentazione.

• È assolutamente necessario proteggere l’unità per mezzo di una fune di sicurezza. Nell’eseguire qual-

siasi intervento attenersi scrupolosamente a tutte le normative (in materia di sicurezza) vigenti nel

paese di utilizzo.

• Installare l’unità in un luogo ben ventilato.

• Mantenere i materiali inammabili ad una distanza di sicurezza dall’unità.

• I ltri, le lenti o gli schermi ultravioletti se danneggiati possono limitare la loro ecienza.

• I LED devono essere sostituiti se danneggiati o termicamente deformati.

• Non guardare direttamente il fascio luminoso. Tenete presente che i veloci cambi di luce possono pro-

vocare attacchi d’epilessia presso persone fotosensibili o epilettiche.

• Non toccare l’alloggiamento del prodotto quando è in funzione perché potrebbe essere molto caldo.

• Questo prodotto è stato progettato e costruito esclusivamente per l’utilizzo indicato in questa docu-

mentazione. Qualsiasi altro utilizzo non espressamente indicato potrebbe pregiudicare la funzionalità

del prodotto e/o rappresentare fonte di pericolo.

• Si declina qualsiasi responsabilità derivata dall’uso improprio del prodotto.

La pagina sta caricando ...

ProLights IP65 160 W zoomable LED ellipsoidal Manuale utente

Marca: ProLights

Modello: IP65 160 W zoomable LED ellipsoidal

Categoria: Stroboscopi

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: ProLights IP65 160 W zoomable LED ellipsoidal User manual

ProLights IP65 160 W zoomable LED ellipsoidal Manuale utente

ProLights IP65 160 W zoomable LED ellipsoidal Manuale utente

in altre lingue

Documenti correlati

Altri documenti