Simplicity RIDER, SMI SPX SIDE DISCHARGE Manuale utente

80088447

Revision B

Not for

Reproduction

2

1

2

3

4

5

6

7

Not for

Reproduction

3

8

9

10

11

12

13

14

15

Not for

Reproduction

4

16

17

18

Not for

Reproduction

5

Table of Contents:

Products Covered by This Manual......................................6

General Information..............................................................6

European Office Contact Information.................................6

European Union (EU) Stage V (5): Carbon Dioxide (CO2)

Values.....................................................................................6

Operator Safety..................................................................... 6

Save these instructions.................................................... 6

Slope Identification Guide................................................ 6

Safety Symbols and Meanings.........................................6

Safety Alert Symbol and Signal Words............................ 7

Safety Decals................................................................... 7

Safety Messages.............................................................8

Features and Controls..........................................................8

Control Symbols and Meanings....................................... 8

Electronic Maintenance Display....................................... 9

Operation............................................................................. 10

Operating Area............................................................... 10

Safety Interlock System Tests........................................11

Engine.............................................................................11

Tractor Operation........................................................... 13

Maintenance.........................................................................15

Maintenance Schedule................................................... 15

Tire Pressure Check...................................................... 15

Battery Maintenance.......................................................15

Mower Blade Stop Time.................................................16

Change the Engine Oil...................................................16

Air Filter Assembly (Cartridge with pre-cleaner).............16

Push the Tractor By Hand............................................. 16

Check the Spark Plugs.................................................. 16

Towed Equipment...........................................................17

Clean the Mower Deck (if equipped)..............................17

Storage.................................................................................17

Troubleshooting..................................................................18

Troubleshooting the Rider..............................................18

Troubleshooting the Mower............................................18

Specifications......................................................................19

Specifications Chart ...................................................... 19

Power Ratings Disclaimer.............................................. 19

Not for

Reproduction

6

Products Covered by This

Manual

The products that follow are covered by this manual:

2691481-00, 2691481-01, 2691481-02, 2691487-00,

2691487-01, 2691487-02, 2691683-00, 2691684-00,

2691685-00, 2691700-00, 2691701-00, 2691702-00,

2691703-00, 2691714-00, 2691715-00

General Information

For additional information, refer to theCustomer Contact

Guideincluded with the unit.

The illustrations in this document are representative.

Your unit might look different from the images

shown.LEFTandRIGHTare referenced from the operator's

position.

The use of Important and Note in the text shows clarifications,

exceptions, or alternatives to the procedures.

All language translations of this document derive from the

initial English source file.

Recycle all packaging, used oil, and batteries according to

applicable government regulations.

European Office Contact

Information

For questions regarding European emissions, please contact

our European office at:

Max-Born-Straße 2, 68519 Viernheim, Germany.

European Union (EU) Stage

V (5): Carbon Dioxide (CO

2

)

Values

Carbon dioxide values of Briggs & Stratton

®

EU Type-

Approval Certificate engines can be found by entering CO2

into the search window on BriggsandStratton.com.

Operator Safety

Save these instructions

Save these instructions for future reference.This manual

contains safety information to make you aware of the hazards

and risks associated with the product and how to avoid them.

It also contains important instructions that must be obeyed

during the initial set-up, operation, and maintenance of the

product.

This product is designed and intended for cutting well

maintained grass and is not intended for other purposes.

It is important that you read and understand these instructions

before you attempt to start or operate this equipment.

Make sure that you are fully familiar with the controls and the

correct use of the product.

Know how to stop the unit and disengage controls quickly.

Slope Identification Guide

How to measure the slope of a lawn surface with a

smartphone or an angle finder tool:

WARNING

Do not operate on slopes greater than10degrees.

1. Use a straight edge at least two (2) feet long (A,

Figure1). A 2x4 or a straight piece of metal works well.

2. Angle finder tools.

a. Use your smartphone:Many smartphones (B,

Figure1) have an inclinometer (angle finder) located

under the compass application (app). Or, search an

app store for an Inclinometer app.

b. Use angle finder tools:Angle finder tools (C and

D, Figure1) are available at local hardware stores

or online (also called inclinometer, protractor, angle

meter, or angle gauge). Dial type (C) or digital type

(D) work, others may not.Read and obey the user

instructions supplied with the angle finder tool.

3. Put the two (2) feet long straight edge along the steepest

part of the lawn slope. Put the board up and down the

slope.

4. Lay the smartphone or angle finder tool on the straight

edge and read the angle in degrees. This is the slope of

your lawn.

Note:A paper gauge slope identification guide is included

in your product literature packet and is also available to

download from the manufacturer's website.

Safety Symbols and Meanings

Symbol Meaning

Safety information about hazards that can result in personal

injury.

Read and understand the Operator's Manual before you

operate or service the unit.

Not for

Reproduction

7

Symbol Meaning

Remove the key and read the Operator's Manual before

you service the unit.

Stop

Fire hazard

Explosion hazard

Shock hazard

Toxic fume hazard

Moving parts

Wear eye protection.

Hazardous chemical

Hot surface hazard

Amputation hazard

Thrown objects hazard

Symbol Meaning

Keep a safe distance

Keep children away

Amputation hazard

Roll-over hazard

Safety Alert Symbol and Signal Words

The safety alert symbol identifies safety information

about hazards that can result in personal injury. A signal word

(DANGER,WARNING, orCAUTION) is used with the alert

symbol to indicate the likelihood and the potential severity of

injury. In addition, a hazard symbol may be used to represent

the type of hazard.

DANGERindicates a hazard which, if not

avoided,willresult in death or serious injury.

WARNINGindicates a hazard which, if not

avoided,couldresult in death or serious injury.

CAUTIONindicates a hazard which, if not

avoided,couldresult inminor or moderate injury.

NOTICEindicates information considered important but not

hazard-related.

Safety Decals

Before you operate the unit, read the safety decals.Compare

Figure2to the decals shown in the table that follows. The

cautions and warnings are for your safety. To avoid personal

injury or damage to the unit, understand and obey the safety

decals.

IMPORTANT:If the safety decals become worn or damaged,

and cannot be read, order replacement decals from your local

dealer.

Not for

Reproduction

8

A

B

Safety Decal Icon Definitions

Compare the letters (A-J) in the safety decal icons to

thesafety definitions listed in the table that follows.

A WARNING:Read and understand the Operator's Manual before

you use this machine. Know the locations and functions of all

controls. Do not operate this machine unless you are trained.

B DANGER - LOSS OF TRACTION, SLIDING, STEERING

AND CONTROL ON SLOPES HAZARD:If the machine stops

forward motion or starts to move on a slope, stop the blades,

andslowlydriveoff the slope.

C DANGER - FIRE HAZARD:Make sure the unit is free of grass,

leaves, and excess oil. Do not add fuel while the engine is hot or on.

Stop the engine. Let the engine cool for at least 3 minutes before

you add fuel. Do not add fuel indoors, in an enclosed trailer, garage

or other enclosed areas. Remove spilled fuel. Do not smoke while

you operate this machine.

D DANGER - TIPPING AND SLIPPING HAZARD:Mow up and down

slopes not across. Do not operate on slopes more than 10 degrees.

Avoid sudden and sharp (fast) turns while on slopes.

E DANGER - AMPUTATION AND DISMEMBERMENT HAZARD:To

avoid injury from rotating blades and moving parts, keep safety

devices (guards, shields and switches) in place and working.

F Do not mow when children or others are around. DO NOT carry

riders especially children even with the blades off. Do not mow

in reverse unless absolutely necessary. Look down and behind –

before and while you drive the unit in reverse.

G Consult technical literature before technical repairs or maintenance.

When you leave the machine, stop the engine, set the parking

brake to the lock position, and remove the ignition key.

H Keep by-standers and children a safe distance away. Remove

objects that can be thrown by the blade. Do not mow without the

discharge chute in place.

I Do not mow without discharge chute or entire grass catcher in

place.

J To avoid injury from rotating blades, stay clear of deck edge and

keep others away.

Safety Messages

WARNING

Read, understand, and obey all the instructions and

warnings in the Operator's Manual and on the machine,

engine, and attachments before you operate this machine.

Failure to obey the safety instructions in this manual and on

the equipment could result in death or serious injury.

• Only let operators who are responsible, trained and

familiar with the instructions and physically capable to

operate the machine.

• Do not operate the machine while under the influence of

alcohol or drugs.

• Wear safety glasses and closed toe footwear.

• Do not put hands or feet near rotating parts or under

the machine. Keep clear of the discharge opening at all

times.

• Keep the machine in good working order. Replace worn

or damaged parts.

• Be careful when youservice the blades. Wrap the

blades or wear gloves. Replace damaged blades. Do

not repair or alterthe blades.

• Use full width ramps when you load and unload a

machine for transport.

• See attachment or accessory for proper wheel weights

or counterweights.

• To help prevent fires, keep machine free of grass,

leaves, or other unwanted material. Clean remaining oil

or fuel spillage. Remove fuel soaked debris and let the

machine to cool before storage.

WARNING

Running engine gives off carbon monoxide, an odorless,

colorless, poison gas. Breathing carbon monoxide can

cause headaches, fatigue, dizziness, vomiting, confusion,

seizures, nausea, fainting or death.

• Operate equipment ONLY outdoors.

• Keep exhaust gas from entering a confined area

through windows, doors, ventilation intakes, or other

openings.

Features and Controls

Make sure that the callout letters in Figure3agree with the

features and controls listed in the table that follows.

Control Symbols and Meanings

A Electronic Dash Panel

Not for

Reproduction

9

B Reverse Mowing Option (RMO)

C Ignition Switch

OFF

ON

START

D Headlight Switch

E Power Take-Off (PTO)

F Power Take-Off(PTO), Engage

Blades

G Power Take-Off (PTO), Disengage

Blades

H Cruise Control

I Parking Brake Control

J Throttle Control

K Throttle Control SLOW Position

L Throttle Control FAST Position

M Choke

N Fuel Level Gauge (if equipped)

O Ground Speed Pedals

P Seat Adjustment Lever

Q Mower Lift Lever

R Height-of-Cut Switch

S Transmission Release Lever

T Fuel Tank

U Brake Pedal

Electronic Maintenance Display

Note:When you start the unit, the Total Hours show on the

maintenance display. The total hours will set to 0 after 999.9.

Display Total Hours, Trip Hours, and Clock

1. Push MODE (A, Figure4) for less than 1 second to show

the Trip Hours.

2. Push RESET (B) for more than 3 seconds to set the Trip

Hours to 0.

Not for

Reproduction

10

3. Push MODE for less than 1 second to show the Clock.

SeeSet the Clocksection.

4. Push MODE for less than 1 second to show the Total

Hours.

Set the Clock

1. Push MODE (A, Figure4) for more than 3 seconds. The

hours will flash on the display.

2. Push RESET to adjust the hours.

3. Push MODE for less than 1 second to save the setting.

The minutes will flash on the display.

4. Push RESET to adjust the minutes.

5. Push MODE for less than 1 second to save the setting.

Maintenance Display

OIL CHANGE- This message shows after 50 hours of

operation. After you change the oil and filter, push MODE two

times to show OIL HRS. Then, push and hold MODE for 3

seconds to set the timer to zero.The display will automatically

clear.

AIR FILTER CHECK- This message shows after 25 hours of

operation. After you clean or change the air filter, push MODE

three times to show AIR FILTER HRS. Then, push and hold

MODE for 3 seconds to set the timer to zero.The display will

automatically clear.

CHANGE BLADES- This message shows after 100 hours

of operation. After you change the blade, hold the RESET

button for more than 3 seconds to set the timer to zero.The

display will automatically clear.

LOW BATTERY- This message shows when a battery

voltage problem occurs. The display will automatically clear

after servicing of the battery.

Note:The LOW BATTERY message shows on the display

before all other messages. Do the servicing ofthe battery

first. Then, do a check for other maintenance messages.

Operation

Read theOperator Safetysection before you operate this

machine. Make sure that you know the controls and how to

stop the unit.

Operating Area

1. Know the area where you plan to operate the mower.

2. Make sure that the area is free of unwanted material that

could be picked up by the blades and thrown.

DANGER

This machine is capable of throwing objects that could

injure bystanders or cause damage to buildings.

• Do not operate the machine without the entire grass

catcher, discharge chute, or other safety devices in

place and functioning properly. Check frequently for

signs of wear or deterioration and replace as needed.

• Clear the operating area of any objects which could

be thrown by or interfere with the operation of the

machine.

3. Move the rider mower outside, before you start the

engine.

WARNING

Engines give off carbon monoxide, an odorless, colorless,

poison gas. Breathing carbon monoxide can cause nausea,

fainting, or death.

4. Note all slopes and drop-offs.

DANGER

Operating on slopes, or near water, or drop-offs can result

in loss of control and roll-over.

• Mow up and down slopes not across.

• Reduce speed and be careful on slopes.

• Do not operate on slopes over 10 degrees, which is a

3.5 foot rise over a 20 foot length.

• Give yourself a minimum of two mower widths of

clearance around water, retaining walls, or drop-offs.

• Avoid mowing wet grass.

• Do not operate machine under any condition where

traction, steering, or stability is in question. Tires could

slide even if the wheels are stopped.

• Avoid starting and stopping on slopes.

• Avoid making sudden changes in speed or direction.

• Make turns slowly and gradually.

• Be careful while operating machine with a grass catcher

or other attachment(s). They can affect the stability of

the machine.

• Follow the manufacturer's recommendation for weight

limits for towed equipment and towing on slopes.

SeeTowed Equipment.

5. Make sure that the operating area is clear of bystanders,

especially children.

Not for

Reproduction

11

DANGER

This rider mower is capable of amputating hands and feet.

• Stop the mower when children or others are near.

• Keep children out of the operating area and under the

watchful care of a responsible adult.

• Do not carry passengers, especially children, even

with the blade(s) shut off. Children can fall off and be

seriously injured or interfere with the safe machine

operation. Children who have been given rides in

the past can suddenly appear in the mowing area for

another ride and be run over or backed over by the

machine.

• Use care when approaching blind corners, shrubs,

trees, or other objects that obscure vision.

Safety Interlock System Tests

This machine is equipped with a Safety Interlock System.

Do not attempt to bypass or tamper with the switches

anddevices.

WARNING

If the machine does not pass a safety test, do not operate

the machine. See an Authorized Dealer.

Test 1 — Engine will NOT crank if:

• Power Take Off (PTO) switch is ON, OR

• Brake pedal is NOT fully pushed down (parking brake

OFF)

Test 2 — Engine will crank and start if:

• PTO switch is OFF, AND

• Brake pedal is fully pushed down (parking brake ON).

Test 3 — Engine will SHUT OFF if:

• Operator rises off seat with PTO engaged, OR

• Operator rises off seat with brake pedal NOT fully pushed

down (parking brake OFF).

Test 4 — Mower Blade Stopping TimeCheck

The mower blades and mower drive belt willcome to a

complete stop in five seconds after the PTO switch is OFF.

If the mower drive belt does not stop in five seconds, see an

Authorized Service Dealer.

Test 5 — Reverse Mowing Option (RMO) Check

• The engine will STOP when reverse travel is attempted

with the PTO switched ON and the Reverse Mowing

Option (RMO) not activated.

• The RMO light will come on when the RMO has been

activated.

DANGER

Mowing in reverse can be hazardous to bystanders. Tragic

accidents can occur if the operator is not alert to the

presence of children. DO NOT activate the Reverse Mowing

Option (RMO) if children are present. Children are often

attracted to the machine and the mowing activity.

Engine

Check and Add Engine Oil

Use Briggs & Stratton

®

Warranty Certified oils for best

performance. Other high-quality detergent oils are acceptable

if classified for service SF, SG, SH, SJ or higher. Do not use

special additives.

Outdoor temperatures determine the proper oil viscosity for

the engine. Use the chart to select the best viscosity for the

outdoor temperature range expected.

A SAE 30 - Below 40 °F (4 °C) the use of SAE 30 will result in hard

starting.

B 10W-30 - Above 80 °F (27 °C) the use of 10W-30 can cause increased

oil consumption. Check oil level more frequently.

C 5W-30

D Synthetic 5W-30

E

Vanguard

®

Synthetic 15W-50



*Below 40°F (4°C) the use of SAE 30 will result in hard starting.



**Above 80°F (27°C) the use of 10W-30 can cause increased oil consumption.

1. Put the unit on a level surface as shown in Figure5.

2. Stop the engine and remove the key. Make sure that the

oil fill area is clean.

3. Remove the dipstick (A, Figure6).Remove the remaining

oil from the dipstick.

4. Install and tighten the dipstick.

5. Remove the dipstick again, and check the oil level.

6. Make sure that the oil level is at the top of the FULL mark

(B) on the dipstick.

7. If the oil level is FULL, install and tighten the dipstick.

8. If the oil level is LOW, add oil into the oil fill tube (C). 

Note:DO NOT add oil at the quick oil drain (if equipped).

9. Wait one minute, and check the oil level again.

10. Install and tighten the dipstick.

Not for

Reproduction

12

Oil Pressure

If the oil pressure is too low, a pressure switch (if equipped)

will either stop the engine or activate a warning device on the

equipment. If this occurs, stop the engine and check the oil

level with the dipstick.

If the oil level is below the ADD mark, add oil until it touches

the FULL mark. Start the engine and check for the correct oil

pressure before you operate the machine.

If the oil level is between the ADD and FULL marks,DO NOT

start the engine. Contact an Authorized Service Dealer to

correct the oil pressure.

Fuel Recommendations

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON). High altitude

use, see below.

• Gasoline with up to 10% ethanol (gasohol) is acceptable.

NOTICE Do not use unapproved gasolines, such as E15

and E85. Do not mix oil in gasoline or modify the engine to

run on alternate fuels. Use of unapproved fuels will damage

the engine components, which will not be covered under

warranty.

To protect the fuel system from gum formation, mix a fuel

stabilizer into the fuel. SeeStorage.All fuel is not the same.

If start or performance problems occur, change fuel providers

or brands. This engine is certified to operate on gasoline.

The emissions control system for carbureted engines is EM

(Engine Modifications). The emissions control systems for

engines with electronic fuel injection are ECM (Engine Control

Module), MPI (Multi Port Injection), and if equipped an O2S

(Oxygen Sensor).

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum 85

octane/85 AKI (89 RON) gasoline is acceptable.

For carbureted engines, high altitude adjustment is

required to maintain performance. Operation without this

adjustment will cause decreased performance, increased

fuel consumption, and increased emissions. Contact

a Briggs & Stratton Authorized Service Dealer for high

altitude adjustment information. Operation of the engine at

altitudes below 2,500 feet (762 meters) with the high altitude

adjustment is not recommended.

For Electronic Fuel Injection (EFI) engines, no high altitude

adjustment is necessary.

Add Fuel

WARNING

Fuel and its vapors are extremely flammable and explosive.

Always handle fuel with extreme care. Failure to Observe

these safety instructions can cause fire or explosion which

could result in severe burns or death.

When Adding Fuel

• Stop the engine and let the engine cool at least 3

minutes before you remove the fuel cap.

• Extinguish all cigarettes, cigars, pipes, and other

sources of ignition.

• Fill fuel tank outdoors or in well-ventilated area.

• Do not overfill fuel tank. To allow for expansion of the

fuel, do not fill above the bottom of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot lights,

heat, and other ignition sources.

• Check fuel lines, tank, cap, and fittings frequently for

cracks or leaks. Replace if necessary.

• If fuel spills, wait until it evaporates before you start the

engine and avoid creating any source of ignition.

• Use only an approved fuel container.

1. Remove unwanted material from the fuel cap area.

2. Remove the fuel cap (A, Figure7).

3. Fill the fuel tank (B) with fuel. DO NOT fill above the

bottom of the fuel tank neck (C).

4. Install the fuel cap.

Start the Engine

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

When you start the engine:

• Make sure that spark plug, muffler, fuel cap, and air

cleaner (if equipped) are installed correctly.

• Do not crank the engine with spark plug removed.

• If the engine floods, set the choke (if equipped) to the

OPEN/RUN position, move the throttle (if equipped) to

the FAST position and crank until engine starts.

WARNING

Engines give off carbon monoxide, an odorless, colorless,

poison gas.

Breathing carbon monoxide can cause nausea, fainting, or

death.

Fire or explosion can cause severe burns or death.

• Start and operate the engine outdoors.

• Do not start or operate the engine in enclosed area,

even if doors or windows are open.

1. Check the oil level. SeeCheck and Add Engine Oil.

Not for

Reproduction

13

2. Make sure that the equipment drive controls are

disengaged.

3. Sit in the seat and lift UP the seat adjustment lever to lock

the seat in position.

4. Engage the parking brake control (I, Figure8). Push the

brake pedal, pull OUT the parking brake control, and

release the brake pedal.

5. Push the PTO switch (E) to disengage it.

6. Set the throttle/choke control (J) to the CHOKE position (if

equipped).

7. Put the key into the ignition switch (C) and turn it to the

START position. For push-button start models, push the

button two times and hold until the engine starts.

8. After the engine starts, move the throttle/choke control

to half speed. Make sure that the engine is ON for a

minimum of 30 seconds. This will warm the engine.

9. Set the throttle/choke control to the FAST position.

Note:In the event of an emergency, turn the ignition switch

to the OFF position. This will STOP the engine. SeeStop the

Engine.



Note:If the engine does not start after 2 or 3 attempts,

contact an Authorized Service Dealer.

Stop the Engine

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

• Do not choke the carburetor to stop the engine.

1. Release the ground speed pedals(O, Figure9).

2. Disengage the Power Take-Off (PTO) switch (E). Wait for

all moving parts to stop.

3. Move the throttle control (J)to the SLOW position.

4. Turn the ignition key switch (C) to the OFF position.

Remove the key.

5. Engage the parking brake control (I). Push the brake

pedal (U), pull UP on the parking brake control, and

release the brake pedal.

In the event of an emergency, turn the ignition switch to the

OFF position. This will STOP engine.

Tractor Operation

1. Sit in the seat and adjust the seat so that you can

comfortably reach all the controls. SeeFeatures and

Controls.

2. Engage the parking brake:

A. Fully push DOWN on the brake pedal.

B. Pull UP on the parking brake control.

C. Release the brake pedal.

3. Disengage the PTO.

4. Start the engine. SeeStart the Engine.

5. Disengage the parking brake:

A. Fully push DOWN on the brake pedal.

B. Push IN the parking brake control.

C. Release the brake pedal.

6. Push DOWN on the speed control pedal to move forward.

Release the pedal to STOP.

Note:The further down the pedal is pushed the faster the

tractor will move.

7. Stop the tractor:

A. Release the speed control pedals.

B. Set the parking brake.

C. STOP the engine. SeeStop the Engine.

Cruise Control

1. Push DOWN on the ground speed pedal (O, Figure3).

SeeFeatures and Controls.

2. When you reach the desired speed, pull UP on the cruise

control. The cruise control will lock in one of its five

locking positions.

3. Push DOWN on the brake pedal (U, Figure3) or

on the ground speed pedal to disengage the cruise

control.SeeFeatures and Controls.

Mowing

DANGER

This machine is capable of amputating hands and feet, and

throwing objects. Failure to obey the safety instructions

could result in serious injury or death.

• Only operate the machine in daylight hours or good

artificial light.

• Avoid holes, ruts, bumps, rocks, or other hidden

hazards.

Uneven terrain can overturn the machine or cause

operator to lose their balance or footing.

• Do not direct discharge material toward anyone. Avoid

discharging material against a wall or obstruction as

material may ricochet back toward the operator.

• Stop the blade(s) when crossing gravel surface.

• Do not leave a running machine unattended. Always

park on level ground, disengage the attachment, set

parking brake, stop engine and remove starter insert or

key.

1. Engage the parking brake control (I,Figure3).

2. Make sure the PTO switch (E)is disengaged.

3. Start the engine. SeeStart the Engine.

4. Set the throttle control (J)to the FAST position.

5. Engage the PTO to activate the mower blades.

6. Use the Height-of-Cut Electric Switch (R) to set the

cutting height to the desired level. SeeAdjusting the

Mower Cutting Height.

Not for

Reproduction

14

7. Disengage the parking brake control, then begin to mow.

8. Disengage the PTO.

9. STOP the engine. SeeStop the Engine.

WARNING

The engine will STOP if the reverse ground speed pedal is

depressed while the PTO is ON and the RMO has not been

activated. Always disengage the PTO OFF before tractor

operation. Sudden loss of drive could create a hazard.

Adjust the Mower Cutting Height

The mower lift lever (Q, Figure3)lowers the deck to cutting

position or raises the deck to the transport position.

1. Lower the deck:

A. Slightly pull back on the mower lift lever.

B. Push the mower lift lever to the left.

C. Push DOWN on the mower lift lever.

2. Raise the deck:

A. Pull UP on the mower lift lever.

B. Lock in the notch to the right.

Note:DO NOT cut when the deck is raised to transport

position.

Note:The height-of-cut switch(R, Figure3)controls the

mower cutting height. It adjusts the cutting height between 1.5

- 3.5 in. (2.5 - 8.89 cm). SeeSpecifications.

Reverse Mowing Option (RMO)

DANGER

Mowing in reverse can be hazardous to bystanders.

Tragic accidents can occur if the operator is not alert to

the presence of children. Children are often attracted to

the machine and the mowing activity. Never assume that

children will remain where you last saw them.

• Keep children out of the operating area and under the

watchful care of a responsible adult.

• Do not carry passengers, especially children, even

with the blade(s) shut off. Children can fall off and be

seriously injured or interfere with the safe machine

operation. Children who have been given rides in

the past can suddenly appear in the mowing area for

another ride and be run over or backed over by the

machine.

• Do not mow in reverse unless absolutely necessary.

Always look down and behind before and while

backing.

• If the machine mows in reverse without Reverse

Mowing Option activated, see an authorized dealer

immediately.

1. Engage the Power Take-Off (PTO) (E, Figure3).

2. Set the Reverse Mowing Option (RMO) key (B)to the ON

position.

3. The L.E.D. light comes on.

4. The operator mows in reverse.

Note:Remove the key to restrict access to the RMO.

Not for

Reproduction

15

Maintenance

WARNING

Unintentional sparking can result in fire or electric shock.

Unintentional start-up can result in entanglement, traumatic

amputation, or laceration.

Before adjustments and repairs:

• Disconnect the spark plug wire. Keep it away from the

spark plug.

• On electric start engines, disconnect the batteryat the

negative (-) terminal.

• Use ONLY the correct tools.

• DO NOT tamper with the governor spring, links, or other

parts to increase engine speed.

• Replacement parts must be of the same design and

installed in the same position as the original parts.

Other parts may not perform as well, may damage the

unit, and may result in injury.

• DO NOT strike the flywheel with a hammer or hard

object because the flywheel can shatter during

operation.

Maintenance Schedule

RIDER AND MOWER

Every 8 Hours or Daily

Check the Safety interlock system.

Remove unwanted material from the rider, mower deck, and engine

compartment.

Every 25 Hours or Annually

*

Check the tire pressure.

Check the mower blade stopping time.

Check for loose hardware on the rider and mower.

Every 50 Hours or Annually

*

Clean the battery and cables.

Check the rider brakes.

Seea Briggs & Stratton Authorized Service Dealer Annually

Lubricate the rider and mower.

Mower blades check**

*Whichever comes first.

**Check the mower blades more often in regions with sandy soils or

high dust conditions.

ENGINE

First 5 Hours

Change the engine oil.

Every 8 Hours or Daily

Check the engine oil level.

Every 25 Hours or Annually

*

Clean the air filter and pre-cleaner.**

Every 50 Hours orAnnually

*

Change the engine oil.

Replace the oil filter.

Annually

Replace the air filter.

ENGINE

Replace the pre-cleaner.

See Dealer Annually to

Inspect the muffler and spark arrester.

Replace the spark plugs.

Replace the fuel filter.

Clean the air cooling system.

*Whichever comes first.

**Clean more often in dusty conditions or when airborne material is

present.

Tire Pressure Check

For the correct traction and the best mowing performance,

make sure that the tire inflation pressure is 12-14

psi (0,82-0,96 bar). Refer to Tire Pressure Check in

theMaintenance Schedule. Also, see Tire Inflation Pressure

in theSpecificationssection.

Note:There can be a difference in tire inflation pressurefrom

the "Maximum Inflation" shown on the side of the tires.

Battery Maintenance

Clean the Battery and Cables

WARNING

When you remove or install battery cables, always

disconnect the NEGATIVE (black) cable FIRST and

reconnect it LAST. If not done in this order, the positive

terminal can be shorted to the frame by a tool.

Note:DO NOT remove or connect the battery cable while the

engine is ON.

1. STOP the engine. Remove the key.

2. Disconnect the NEGATIVE (-)cables (A, Figure10) from

the battery first.

3. Disconnect the POSITIVE (+) cables (B) from the battery

last.

4. Clean the battery surface with baking soda and water.

5. Use a wire brush and terminal cleaner to to clean the

battery terminals and cable ends.

6. Lubricate the battery terminals with petroleum jelly or

non-conducting grease.

7. Install the battery.

8. Connect thePOSITIVE (+) cables to the battery first.

9. Connect thethe NEGATIVE (-)cablesto the battery last.

Charge the Battery

WARNING

Keep open flames and sparks away from the battery.

Gassesfrom the battery are very explosive.

Not for

Reproduction

16

A dead battery or one too weak to start the engine can

be the result of a defect in the charging system or other

electrical component. If there are doubts about the cause of

the problem, see an Authorized Service Dealer. To replace

the battery, seeClean the Battery and Cables.

Mower Blade Stop Time

WARNING

If the mower blade does not STOP in 5 seconds or less,the

clutch must be adjusted. DO NOT operate the machine

until the adjustment has been corrected by aBriggs &

StrattonAuthorizedService Dealer.

After the Power Take-Off (PTO) switch turns OFF, the mower

blades and mower drive belt must STOP in 5 seconds or

less.If the mower drive belt does not STOP in 5 seconds,

contact Briggs & Stratton Authorized Service Dealer for

repairs.

Change the Engine Oil

1. Put the rider on a level surface (A, Figure11).

2. Stop the engine and remove starter insertor key (B).

3. Clean the oil fill and filter areas.

4. Remove the dipstick(C).

5. Disconnect the oil drain hose (A,Figure12)

6. Carefully remove the cap (B),and lower the hose into an

approved container (C).

7. After the oil has drained, installthe cap tightly, then attach

the hose to the side of the engine.

8. Remove the oil filter (B, Figure13) and discard.

9. Lightly lubricate the oil filter gasket (A) with clean oil.

10. Install the oil filter by hand until the gasket touches the

oil filter adapter (C). Then, tighten the oil filter 1/2 to 3/4

turns.

11. Add oil.Refer to theCheck and Add Oilsection.

Air Filter Assembly (Cartridge with pre-

cleaner)

WARNING

DO NOT start or operate the engine without an air cleaner

assembly or air filter as it is a fire hazard.

NOTICE DO NOT use pressurized air or solvents to clean

the air filter. Pressurized air can damage the filter and

solvents will dissolve it.

1. Loosen the fasteners (A, Figure14) and remove the

cover (B).

2. Remove the air cleaner assembly (C) and disassemble it.

3. Remove unwanted material or debris that can get into the

carburetor throat (D).

4. Remove the pre-cleaner from the air filter.

5. Lightly tap the air filter on a hard surface to loosen debris.

If the air filter is dirty, replace it.

6. Soak the pre-cleaner in liquid detergent and water. Let it

fully air dry. DO NOT lubricate the pre-cleaner.

7. Assemble the dry pre-cleaner to the air filter.

8. Install the air filter assembly.

9. Install the cover and tighten the fasteners.

Push the Tractor By Hand

1. Disengage the Power-Take-Off (PTO) (E, Figure3).

2. STOP the engine. SeeStop the Engine.

3. Pull the transmission release lever (S, Figure15). Then,

push the lever down to lock in position.

4. The rider can be pushed by hand.

WARNING

Towing the unit will cause transmission damage. Do not use

another vehicle to push or pull this unit. Do not actuate the

transmission release lever while the engine is ON.

Check the Spark Plugs

WARNING

Unintentional sparking can result in fire or electric shock.

Unintentional start-up can result in entanglement, traumatic

amputation, or laceration.

When you test for spark:

• Use an approved spark plug tester.

• DO NOT check for spark with the spark plug removed.

NOTICE Spark plugs have different heat ranges. It is

important that the correct spark plug is used, otherwise,

engine damage can occur. Replace the spark plug with the

same type or equivalent one.

Clean the Spark Plugs

Clean the spark plugswith a wire brush and sturdy knife. DO

NOT use abrasives.

Check the Spark Plug Gap

Use a spark plug feeler gauge (A,Figure16) to check the

gap between the two electrodes. When the gap is correct, the

gauge will drag slightly as you pull it through the gap.

To adjust the spark plug gap, use a spark plug gauge and

gently bend the curved electrode. Make sure that you do not

touch the center electrode or the porcelain.

Install the Spark Plugs

Tighten the spark plug with your fingers, and then, tighten it

with a wrench as shown in Figure 17.

• 180 in-lbs (20 Nm), OR

• 1/2 turn when you install the original spark plug, OR

• 1/4 turn when you install a new spark plug.

Not for

Reproduction

17

Towed Equipment

1. Before you tow the unit, make sure that the hitch is

designed for towing.

2. Attach towed equipment ONLY at the hitch point.

3. For towed equipment and towing on slopes, make sure

that the weight limit recommendationsare correct.

• Gross weight (trailer and load) of 400 lb (181.4 kg).

• Maximum of 20 lb (9.1 kg) foot up or down on the

tongue.

• Go from a 10° limit to a 5°limit on slopes.

4. DO NOT let children or others in or on towed equipment.

5. The weight of the towed equipment on slopes can cause

loss of traction and loss of control.

6. DO NOT shift to neutral and coast down hill.

Clean the Mower Deck (if equipped)

Note:Use the washout port (C, Figure18) to clean the bottom

of the mower deck.

1. Put the rider on a smooth level surface.

2. Attach the quick disconnect (A,Figure18)to the garden

hose (B) and then connect to the washout port (C)on the

mower deck.

3. Turn the water ON.

4. Start the engine. SeeStart the Engine.

5. Set the Height-of-Cut to the highest position. SeeAdjust

the Mower Cutting Height.

6. Engage the Power Take-Off (PTO) to activate the mower

blades.The rotation of the blades and the water will clean

the bottom of the mower deck.

7. Disengage the PTO.

8. Stop the engine. SeeStop the Engine.

9. Turn the water OFF.

10. Remove the garden hose and quick disconnect from the

washout port (C).

Storage

WARNING

Never store the unit (with fuel) in an enclosed, non-

ventilated structure. Fuel vapors can travel to an ignition

source (such as a furnace, water heater, etc.) and cause an

explosion.

• Store away from furnaces, stoves, water heaters, or

other appliances that have pilot lights or other ignition

sources because they can ignite fuel vapors.

Equipment

Turn OFF the Power Take-Off (PTO), and set the parking

brake. Remove the starter insert.Let the machine cool.

If you remove the battery, the battery life will increase. Make

sure that thebattery is in a cool, and dry location, and keep

it fully charged. If the battery is left in the unit, disconnect the

negative cable.

Fuel System

Fuel can become stale when kept in a storage container

for more than 30 days. Each time you fill the container

with fuel, addfuel stabilizerto the fuel as specified by the

manufacturer’s instructions. This keeps fuel fresh and

decreases fuel-related problems or contamination in the fuel

system.

It is not necessary to drain fuel from the engine whenfuel

stabilizeris added as instructed. Before storage, turn the

engine ON for 2 minutes to move the fuel and stabilizer

through the fuel system.

Before starting the machine after it has been stored:

• Check all fluid levels. Check all maintenance items.

• Do all recommended checks and procedures found in this

manual.

• Make sure the engine is warm before you use it.

Not for

Reproduction

18

Troubleshooting

Troubleshooting the Rider

PROBLEM LOOK FOR REMEDY

The brake pedal is not pushed down. Fully push down on the brake pedal.

The fuel tank is empty. If engine is hot, let it cool, and then fill the fuel tank

again.

The PTO switch is in ON position. Set the PTO switch to the OFF position.

The cruise control is engaged. Set the cruise control to the NEUTRAL/OFF

position.

The engine is flooded. Disengage the choke.

The battery terminals are dirty. Refer toClean the Battery and Cables.

The battery is discharged or dead. Charge or replace the battery.

The engine will not turn over or start.

Loose or broken wiring. Visually check wiring. If wires are frayed or broken,

see an Authorized Service Dealer.

The engine starts hard or runs poorly. The fuel mixture is too rich. Clean the air filter.

Low oil level. Check and add oil as required.The engine knocks.

Incorrect grade of oil. Refer to theCheck and Add Engine Oilsection.

The engine is too hot. Check the engine fins, blower screen, and air

cleaner (if equipped).

Incorrect grade of oil. Refer to theCheck and Add Engine Oilsection.

Excessive oil consumption.

Too much oil in crankcase. Drain excess oil.

The air filter is dirty.  Refer to theAir Filter Assemblysection.The engine exhaust is black.

The choke is closed. Open the choke.

The speed control pedals are not pushed down. Push down on the speed control pedals.

The transmission release lever is in the PUSH

position.

Move the transmission release lever to the DRIVE

position.

The engine runs, but the rider will not drive.

The parking brake is engaged. Disengage the parking brake.

The rider steers hard or handles poorly. Incorrect tire inflation. Refer to theCheck Tire Pressuresection.

Note:For all other problems, contact an Authorized Service Dealer.

Troubleshooting the Mower

PROBLEM LOOK FOR REMEDY

The mower cut is uneven. The tires are not correctly inflated. Refer to theTire Pressure Checksection.

The engine speed is too slow. Set to FAST throttle.The mower cut looks rough.

The ground speed is too fast. Slow down.

The engine speed is too slow. Set to FAST throttle.

The ground speed is too fast. Slow down.

Dirty or clogged air cleaner. Refer to theAir Filter Assemblysection.

Height-of-Cut is set too low. Cut tall grass at maximum Height-of-Cut during first

pass.

The engine stalls easily with the mower engaged.

The engine is not at the operating temperature. START the engine,and let it warmfor several

minutes.

The engine starts, and the rider drives, but the

mower will not cut.

The Power-Take Off (PTO) is disengaged. Engage the PTO.

Note:For all other problems, contact an Authorized Service Dealer.

Not for

Reproduction

19

Specifications

Specifications Chart

Item

2691481, 2691487,

2691683

2691482,

2691488, 2691576

2691483, 2691489 2691714

Engine Intek™Briggs & Stratton Intek™Briggs & Stratton Professional Series™Briggs

& Stratton

Intek™Briggs & Stratton

Displacement 656 cc 656 cc 725 cc 656 cc

Electrical System 9-Amp 9-Amp 9-Amp 9-Amp

Battery 12V - 195CCA 12V - 195CCA 12V - 230CCA 12V - 195CCA

Oil Capacity 64 oz (1,9 L) 64 oz (1,9 L) 64 oz (1,9L) 64 oz (1,9L)

Spark Plug Gap .030 in (,76 mm) .030 in (,76 mm) .030 in (,76 mm) .030 in (,76 mm)

Spark Plug Torque 180 lb-in (20 Nm) 180 lb-in (20 Nm) 180 lb-in (20 Nm) 180 lb-in (20 Nm)

Fuel Tank Capacity 13.2 L 13.2 L 13.2 L 11 L

Transmission

Make and Type

Tuff Torq

®

K46 Tuff Torq

®

K46 Tuff Torq

®

K46 Tuff Torq

®

K46

Chassis

Front Wheel Size 15 x 6-6 15 x 6-6 15 x 6-6 15 x 6-6

Front Wheel Inflation

Pressure

12 - 14 psi (0,82 - 0,92 Bar) 12 - 14 psi (0,82 - 0,92 Bar) 12 - 14 psi (0,82 - 0,92 Bar) 12 - 14 psi (0,82 - 0,92 Bar)

Rear Wheel Size 20 x 8-8 22 x 10-8 22 x 9.5-12 20 x 8-8

Rear Wheel Inflation

Pressure

10 psi (0,68 Bar) 10 psi (0,68 Bar) 10 psi (0,68 Bar) 10 psi (0,68 Bar)

Item 2691701, 2691715 2691684, 2691702 2691685, 2691703 2691700

Engine Intek™Briggs & Stratton Professional Series™Briggs

& Stratton

Professional Series™Briggs

& Stratton

Intek™Briggs & Stratton

Displacement 656 cc 725 cc 725 cc 656 cc

Electrical System 9-Amp 9-Amp 9-Amp 9-Amp

Battery 12V - 195CCA 12V - 230CCA 12V - 230CCA 12V - 195CCA

Oil Capacity 64 oz (1,9 L) 64 oz (1,9 L) 64 oz (1,9 L) 64 oz (1,9 L)

Spark Plug Gap .030 in (,76 mm) .030 in (,76 mm) .030 in (,76 mm) .030 in (,76 mm)

Spark Plug Torque 180 lb-in (20 Nm) 180 lb-in (20 Nm) 180 lb-in (20 Nm) 180 lb-in (20 Nm)

Fuel Tank Capacity 11 L 11 L 11 L 11 L

Transmission

Make and Type

Tuff Torq

®

K46 Tuff Torq

®

K46 Tuff Torq

®

K46 Tuff Torq

®

K46

Chassis

Front Wheel Size 15 x 6-6 15 x 6-6 15 x 6-6 15 x 6-6

Front Wheel Inflation

Pressure

12 - 14 psi (0,82 - 0,92 Bar) 12 - 14 psi (0,82 - 0,92 Bar) 12 - 14 psi (0,82 - 0,92 Bar) 12 - 14 psi (0,82 - 0,92 Bar)

Rear Wheel Size 22 x 10-8 22 x 9.5-12 22 x 9.5-12 20 x 10-8

Rear Wheel Inflation

Pressure

10 psi (0,68 Bar) 10 psi (0,68 Bar) 10 psi (0,68 Bar) 10 psi (0,68 Bar)

Power Ratings Disclaimer

Power Ratings:The gross power rating for individual

gasoline engine models is labeled in accordance with

SAE (Society of Automotive Engineers) code J1940 Small

Engine Power & Torque Rating Procedure, and is rated in

accordance with SAE J1995. Torque values are derived at

2600 RPM for those engines with “rpm” called out on the

label and 3060 RPM for all others; horsepower values are

derived at 3600 RPM. The gross power curves can be viewed

at www.BRIGGSandSTRATTON.COM. Net power values are

taken with exhaust and air cleaner installed whereas gross

power values are collected without these attachments. Actual

gross engine power will be higher than net engine power

and is affected by, among other things, ambient operating

conditions and engine-to-engine variability. Given the wide

array of products on which engines are placed, the gasoline

engine may not develop the rated gross power when used in

a given piece of power equipment. This difference is due to

a variety of factors including, but not limited to, the variety of

engine components (air cleaner, exhaust, charging, cooling,

carburetor, fuel pump, etc.), application limitations, ambient

operating conditions (temperature, humidity, altitude), and

Not for

Reproduction

20

engine-to-engine variability. Due to manufacturing and

capacity limitations, Briggs & Stratton may substitute an

engine of higher rated power for this engine.

Not for

Reproduction

La pagina sta caricando ...

Simplicity RIDER, SMI SPX SIDE DISCHARGE Manuale utente

Questo manuale è adatto anche per

Simplicity RIDER, SMI SPX SIDE DISCHARGE Manuale utente

in altre lingue

Documenti correlati

Altri documenti