Dometic PERFECTVIEW VT100DIG Istruzioni per l'uso

VT100DIG

Digital radio link

Installation and Operating Manual . . . . . . 7

Digitale Funkstrecke

Montage- und Bedienungsanleitung . . . 19

Systéme radio numérique

Instructions de montage

et de service . . . . . . . . . . . . . . . . . . . . . . . 32

Tramo de transmisión por radio

digital

Instrucciones de montaje y de uso . . . . .45

Percurso digital

Instruções de montagem e manual de

instruções . . . . . . . . . . . . . . . . . . . . . . . . . 58

Tratta radio digitale

Istruzioni di montaggio e d’uso . . . . . . . . 71

Digitaal zendbereik

Montagehandleiding en

gebruiksaanwijzing. . . . . . . . . . . . . . . . . . 84

Digital trådløs forbindelse

Monterings- og betjeningsvejledning. . . 97

Digital radiolänk

Monterings- och bruksanvisning . . . . . . 109

Digital radiolink

Monterings- og bruksanvisning . . . . . . .121

Digitaalinen radiolinkki

Asennus- ja käyttöohje. . . . . . . . . . . . . . 133

Устройство цифровой

радиосвязи

Инструкция по монтажу

и эксплуатации. . . . . . . . . . . . . . . . . . . . 146

Cyfrowe łącze radiowe

Instrukcja montażu i obsługi . . . . . . . . . 160

Digitálne rádiorelé spojenie

Návod na montáž a uvedenie

do prevádzky . . . . . . . . . . . . . . . . . . . . . 173

Zařízení k přenosu digitálního

rádiového signálu

Návod k montáži a obsluze . . . . . . . . . . 186

Digitális rádiós szakasz

Szerelési és használati útmutató . . . . . . 198

EN

DE

FR

ES

PT

IT

NL

DA

SV

NO

FI

RU

PL

SK

CS

HU

DRIVING SUPPORT

PERFECTVIEW

VT100DIG-IO-16s.book Seite 1 Montag, 1. August 2016 2:46 14

VT100DIG-IO-16s.book Seite 2 Montag, 1. August 2016 2:46 14

VT100DIG

3

1

2

3

4

9

6 8

5

7

10

11

12

1

VT100DIG-IO-16s.book Seite 3 Montag, 1. August 2016 2:46 14

VT100DIG

4

2

3

2.

1.

4

12

5

VT100DIG-IO-16s.book Seite 4 Montag, 1. August 2016 2:46 14

VT100DIG

5

65

7 8

4

1

2

3

6

1

2

3

5

6

4

7

VT100DIG-IO-16s.book Seite 5 Montag, 1. August 2016 2:46 14

VT100DIG

6

8

9

VT100DIG-IO-16s.book Seite 6 Montag, 1. August 2016 2:46 14

VT100DIG Explanation of symbols

EN

7

Please read this instruction manual carefully before installation and first use, and store

it in a safe place. If you pass on the product to another person, hand over this instruc-

tion manual along with it.

Table of contents

1 Explanation of symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2 Safety and installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

3 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

4 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

5 Technical description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

6 Installing the radio link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

7 Connecting electrical power to the radio link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

8 Pairing the system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

9 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

10 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

11 Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

12 Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

1 Explanation of symbols

!

A

I

WARNING!

Safety instruction: Failure to observe this instruction can cause fatal or serious injury.

CAUTION!

Safety instruction: Failure to observe this instruction can lead to injury.

NOTICE!

Failure to observe this instruction can cause material damage and impair the function

of the product.

NOTE

Supplementary information for operating the product.

VT100DIG-IO-16s.book Seite 7 Montag, 1. August 2016 2:46 14

Safety and installation instructions VT100DIG

EN

8

2 Safety and installation instructions

The manufacturer accepts no liability for damage in the following cases:

• Damage to the product resulting from mechanical influences and excess voltage

• Alterations to the product without express permission from the manufacturer

• Use for purposes other than those described in the operating manual

Please observe the prescribed safety instructions and stipulations from the vehicle

manufacturer and service workshops.

!

WARNING!

Inadequate supply cable connections could result in short circuits, which could have as

a consequence that:

• Cable fires occur

• The airbag is triggered

• Electronic control devices are damaged

• Electric functions fail (indicators, brake light, horn, ignition, lights)

A

NOTICE!

To prevent the risk of short circuits, always disconnect the negative terminal of the vehi-

cle's electrical system before working on it.

If the vehicle has an additional battery, its negative terminal should also be discon-

nected.

Please observe the following instructions:

• When working on the following cables, only use insulated cable lugs, plugs and flat push-on

receptacles:

– 30 (direct supply from positive battery terminal)

–15 (connected positive terminal, behind the battery)

– 31 (return line from the battery, earth)

– L (indicator lights left)

– R (indicator lights right)

Do not use terminal strips.

• Use a crimping tool to connect the cables.

• When connecting to cable 31 (earth), screw the cable

– to the vehicle's earth bolt with a cable lug and a gear disc or

– to the sheet-metal bodywork with a cable lug and a self-tapping screw.

Ensure that there is a good earth connection.

VT100DIG-IO-16s.book Seite 8 Montag, 1. August 2016 2:46 14

VT100DIG Safety and installation instructions

EN

9

If you disconnect the negative terminal of the battery, all data stored in the volatile memories will

be lost.

• The following data must be set again, depending on the vehicle equipment options:

–Radio code

– Vehicle clock

–Timer

– On-board computer

– Seat position

You can find instructions for making these settings in the appropriate operating instructions.

Observe the following installation instructions:

!

CAUTION!

• Secure the parts installed in the vehicle in such a way that they cannot become loose

under any circumstances (sudden braking, accidents) and cause injuries to the

occupants of the vehicle.

• Secure any parts of the system covered by the bodywork in such a manner that they

cannot be come loose or damage other parts and cables or impair vehicle functions

(steering, pedals, etc).

• Always follow the safety instructions of the vehicle manufacturer.

Some work (e.g. on retention systems such as the AIRBAG etc.) may only be per-

formed by qualified specialists.

A

NOTICE!

• To prevent damage when drilling, make sure there is sufficient space on the other

side for the drill head to come out.

• Deburr all drill holes and treat them with a rust-protection agent.

Observe the following instructions when working with electrical parts:

A

NOTICE!

• When testing the voltage in electrical cables, only use a diode test lamp or a voltme-

ter.

Test lamps with an illuminant take up voltages which are too high and which can dam-

age the vehicle's electronic system.

• When making electrical connections, ensure that:

– they are not kinked or twisted

– they do not rub on edges

– they are not laid in sharp edged ducts without protection.

• Insulate all connections.

• Secure the cables against mechanical wear with cable binders or insulating tape,

for example to existing cables.

VT100DIG-IO-16s.book Seite 9 Montag, 1. August 2016 2:46 14

Scope of delivery VT100DIG

EN

10

3Scope of delivery

4Intended use

The PerfectView VT100DIG radio link (ref. no. 9600000068) is used for the wireless transmission

of signals between the camera and the monitor for the PerfectView reversing video systems from

2011.

5 Technical description

5.1 Function description

The radio link consists of a transmitter module and a receiver module. The two modules can be

mounted inside or outside the vehicle. They transmit pictures and sound wirelesssly from the

camera to the monitor.

The transmitter module is preferably supplied with a voltage via the ignition plus and is also used

to supply the camera with a voltage. When connecting only with the reversing light, the system

pairing cannot be started in reverse gear.

The receiver module is powered by the monitor. The wireless signals are transmitted in the

2.4 GHz range.

Since the system is designed merely as an additional aid for reversing, it does not relieve you of

the duty to take proper care when reversing.

A

No. in

fig. 5, page 4

Quantity Description

1 1 Transmitter module

21Receiver module

––Fastening material

NOTICE!

• VT100DIG transmits digital data. The data is displayed on the monitor 0.2 s after it

is recorded by the camera. Therefore, it is essential that you drive slowly.

• If the monitor displays a yellow warning triangle, there is a fault in the picture

transmission. It is possible that the display of the camera image on the monitor is

delayed. Therefore the system may not be used as an aid during reversing in such

circumstances.

VT100DIG-IO-16s.book Seite 10 Montag, 1. August 2016 2:46 14

VT100DIG Technical description

EN

11

5.2 Control elements

You will find the following control elements on the transmitter module:

The receiver module has the following control elements:

No. in

fig. 6, page 5

Meaning

1 Antenna connection

2 Pairing button

3 Operating mode display:

• LED glows red when signals are being transmitted

• LED flashes red when the components are being paired

4 Camera connection

5 Blue cable (CAMERA POWER TRIGGER): voltage supply for camera and

switch input for protective cover of CAM80 (see page 15)

6 Green cable (REVERSE TRIGGER): control cable for activating the pairing

signal

7 Red cable (DC INPUT): Connection to the positive terminal of the

voltage supply; preferably ignition plus

8 Black cable (GND): Connection to the negative terminal of the voltage

supply or earth

No. in

fig. 7, page 5

Meaning

1 Antenna connection

2 Pairing button

3 Operating mode display:

• LED glows red when signals are being transmitted

• LED flashes red when the components are being paired

4 Monitor connection

5 Green cable (REVERSE TRIGGER): control cable for activating the pairing

signal

6 Black cable (GND): Connection to earth

VT100DIG-IO-16s.book Seite 11 Montag, 1. August 2016 2:46 14

Installing the radio link VT100DIG

EN

12

6 Installing the radio link

6.1 Tools required

For installation and assembly, you will need the following tools:

• Drill bit set (fig. 1 1, page 3)

• Electric drill (fig. 1 2, page 3)

• Screwdriver (fig. 1 3, page 3)

• Set of ring or open-ended spanners (fig. 1 4, page 3)

• Measuring ruler (fig. 1 5, page 3)

• Hammer (fig. 1 6, page 3)

• Centre punch (fig. 1 7, page 3)

To establish and test the electrical connection, the following tools are required:

• Diode test lamp (fig. 1 8, page 3) or voltmeter (fig. 1 9, page 3)

• Crimping tool (fig. 1 10, page 3)

• Insulating tape (fig. 1 11, page 3)

• Cable bushing sleeves (optional)

To fasten the module and the cables, you may need additional screws and cable binders.

6.2 Installing the modules

!

Observe the following installation instructions:

• Install the modules so that as few objects as possible are between them.

Metal objects in particular can hinder radio transmission.

• If possible, install the modules in the vehicle.

The housings are splash-water protected and can be mounted outside the vehicle. In this

case, you need to select a location that is protected against mechanical impacts (e.g. flying

stones).

• The installation location should be flat.

• Before drilling, check each time that there is sufficient space on the other side for the drill head

to emerge (fig. 2, page 4).

• Transmitter module: Make sure you can lay the connection cable to the camera.

• Receiver module: Make sure you can lay the connection cable to the monitor.

CAUTION!

Select the location of the modules so that they cannot injure the passengers in the

vehicle under any circumstances (e.g. sudden braking, road traffic accidents).

VT100DIG-IO-16s.book Seite 12 Montag, 1. August 2016 2:46 14

VT100DIG Connecting electrical power to the radio link

EN

13

I

To perform the installation, proceed as follows:

➤ Attach the modules temporarily to the planned installation location.

➤ Install the rear view video system if you have not already done so.

➤ Start up the rear view video system.

If the camera image transmission is stable (two or three reception bars at the top right of the

monitor), you can complete final installation of the two modules.

If faults occur (only one reception bar or a yellow warning triangle on the top right of the

monitor) turn or move the transmitter or receiver module slightly and conduct further tests.

Attaching the modules (fig. 8, page 6)

To do this, proceed as follows for each module:

➤ Hold the module at the chosen location and mark the four points for drill holes.

➤ Drill holes with a Ø of 4 mm at each of the points you just marked.

➤ Screw the module on with M5 x 20mm self-tapping screws.

Fixing the antennas (fig. 9, page 6)

I

➤ You can glue the antennae on the corresponding module.

7 Connecting electrical power to the radio link

7.1 General notes on laying cables

I

NOTE

Pictures and sound are sent from the transmitter module to the receiver module. To

ensure flawless functioning, you need to check whether the wireless transmission is

stable before final installation.

NOTE

Always align the antennas in the same direction, for example, both vertically.

This improves the transmission performance.

NOTE

• As far as possible, use original ducts for laying the cables, or other suitable options

such as panelling edges, ventilation grilles or dummy plugs. If no openings are avail-

able, you must drill holes for the cables. Check beforehand that there is sufficient

space on the other side for the drill head to emerge.

• Cables and connections that are not properly installed will cause malfunctions or

damage to components. Correct installation of cables and connections ensures

lasting and trouble-free operation of the retrofitted components.

VT100DIG-IO-16s.book Seite 13 Montag, 1. August 2016 2:46 14

Connecting electrical power to the radio link VT100DIG

EN

14

Therefore, please observe the following instructions:

• Wherever possible, lay cables inside the vehicle, as they are better protected there than

outside.

If you do need to lay a cable outside the vehicle, ensure that it is well fastened (use additional

cable ties, insulating tape etc.).

• To prevent damage to the cables when laying them, ensure that they are far enough away from

hot or moving vehicle components (exhaust pipes, drive shafts, light systems, fans, heaters

etc.).

• Screw on the plug connections of the connecting cables to protect against water penetration

(fig. 4, page 4).

• When laying the cables, make sure:

– they are not kinked or twisted

– they do not rub on edges

– they are not laid in sharp-edged ducts without protection (fig. 3, page 4).

• Protect every through-hole made in the bodywork against water penetration, e.g. by using a

cable with a sealant and by spraying the cable and the cable sleeve with sealant.

I

7.2 Connecting electrical power to the transmitter module

A

VT100DIG requires a few seconds to initiate the digital wireless connection. To keep this start-up

time short, you should connect the transmitter module to an active +12 V voltage supply. If no

continuous operating voltage is available, you can connect the transmitter module to the reversing

light.

Connecting the transmitter module to a continuous operating voltage

➤ Connect the red cable of the transmitter module (fig. 6 7, page 5) to an active positive cable,

e.g. terminal 15.

➤ Connect the black cable of the transmitter module (fig. 6 8, page 5) to earth (bodywork).

➤ Connect the green cable of the transmitter module (fig. 6 6, page 5) to the reversing light.

A

NOTE

Only start sealing through-holes when you have completed all installation work on the

camera and have laid the required cable lengths.

NOTICE!

Make sure the polarity is correct.

NOTICE!

Always connect the green cable to the reversing light and not to a continuous

operating voltage or an active positive cable. The "pairing" is started via this cable by

engaging the reverse gear three times.

VT100DIG-IO-16s.book Seite 14 Montag, 1. August 2016 2:46 14

VT100DIG Connecting electrical power to the radio link

EN

15

➤ Connect the blue cable of the transmitter module (fig. 6 5, page 5) depending on the type

of camera.

– Camera without motorised protective cover to an active positive cable

– Camera with motorised protective cover to the reversing light

➤ Connect the camera connector (fig. 6 4, page 5) to the camera.

Connecting the transmitter module to the reversing light (no continuous operating

voltage)

I

➤ Connect the red cable of the transmitter module (fig. 6 7, page 5) to the positive wire (+) of

the reversing light.

➤ Connect the black cable of the transmitter module (fig. 6 8, page 5) to the earth wire (–) of

the reversing light or to earth (bodywork).

➤ Connect the blue cable of the transmitter module (fig. 6 5, page 5) to the positive wire of the

reversing light.

➤ Connect the camera connector (fig. 6 4, page 5) to the camera.

A

7.3 Connecting electrical power to the receiver module

➤ Connect the green cable of the receiver module (fig. 7 5, page 5) to the reversing switch.

➤ Connect the black cable of the receiver module (fig. 7 6, page 5) to earth (bodywork).

➤ Connect the monitor connector (fig. 7 4, page 5) to the monitor.

➤ Switch on the monitor.

✓ The monitor displays the message “Wait Tx Signal …”.

NOTE

• These connection options only work with the cameras CAM50C, CAM60CM or

CAM30C.

• On some vehicles, the reversing light only works when the ignition is switched on.

In this case, you must switch on the ignition in order to identify the positive and earth

wires.

• If the transmitter module is only connected via the reversing light, the system pairing

cannot be started in the reverse gear.

NOTICE!

The green cable may not be used.

Pairing the transmitter and receiver is only possible when reverse gear is engaged via

the button!

VT100DIG-IO-16s.book Seite 15 Montag, 1. August 2016 2:46 14

Pairing the system VT100DIG

EN

16

8 Pairing the system

I

8.1 Pairing the system manually with the pairing button

➤ Press the pairing button on the receiver module (fig. 7 2, page 5) three times within 10 s

(press the button approx. 1 time per second).

✓ The LED on the receiver module (fig. 7 3, page 5) flashes red.

✓ The monitor displays the message “Pairing Start” and a counter that counts down 50 s.

You need to perform the pairing of the transmitter module within 50 s.

➤ Press the pairing button on the transmitter module (fig. 6 2, page 5) three times within 10 s

(press the button approx. 1 time per second).

✓ The LED on the transmitter module (fig. 6 3, page 5) flashes red.

✓ The modules synchronise themselves with each other.

This takes approx. three to five seconds. For successful pairing, the monitor shows the “Save

data” message and the picture appears.

If pairing is unsuccessful, the monitor displays the message “Pairing Failed”. Repeat

the pairing procedure.

8.2 Pairing the system with reverse gear

You can start pairing the module via the reverse gear if you connect the red cable from the trans-

mitter module to the positive terminal and the green cable of both modules on the reversing light.

➤ Switch on the monitor.

➤ Activate the required channel.

➤ Engage and disengage the reverse gear three times within 10 s.

✓ The LED on the transmitter module (fig. 6 3, page 5) and the LED on the receiver module

(fig. 7 3, page 5) flash red.

✓ The modules synchronise themselves with each other.

This takes approx. three to five seconds. For successful pairing, the monitor shows the “Save

data” message and the picture appears.

If pairing is unsuccessful, the monitor displays the message “Pairing Failed”. Repeat

the pairing procedure.

NOTE

The transmitter module and the receiver module have to be paired with each other so

that the monitor can display the camera images. This is conducted at the factory.

VT100DIG-IO-16s.book Seite 16 Montag, 1. August 2016 2:46 14

VT100DIG Troubleshooting

EN

17

9 Troubleshooting

10 Warranty

The statutory warranty period applies. If the product is defective, please contact the

manufacturer's branch in your country (see the back of the instruction manual for the addresses) or

your retailer.

For repair and guarantee processing, please include the following documents when you send in

the device:

• A copy of the receipt with purchasing date

• A reason for the claim or description of the fault

Fault Cause Suggested remedy

The monitor displays the

message “NO SIGNAL”.

The transmitter module is

not working.

Check the voltage supply.

The monitor displays the

message “REVERSE

FOR IMAGE”.

The green and the blue

cable are incorrectly con-

nected.

Check the camera connection and

function.

The transmitter module is

not receiving a video sig-

nal.

The monitor displays the

message “Pairing

Failed”.

The start signal (on/off

three times) is incomplete

or missing.

Repeat the system pairing until the

monitor displays “Save data”.

The monitor displays the

message “wait for

TX”.

Transmitter and receiver

modules have lost identi-

fication.

Engage reverse gear again.

Start system pairing.

The transmitter module

has no voltage supply.

Check the voltage supply.

Irregular image playback

or yellow warning triangle

on the screen.

– Make sure that the antennae of the

receiver module and the transmitter

module are firmly connected.

Check the reception bars on the moni-

tor. If only one reception bar is dis-

played, change the position of the

transmitter or receiver module.

Check if the battery charge is sufficient.

VT100DIG-IO-16s.book Seite 17 Montag, 1. August 2016 2:46 14

Disposal VT100DIG

EN

18

11 Disposal

➤ Place the packaging material in the appropriate recycling waste bins wherever possible.

M

If you wish to finally dispose of the product, ask your local recycling centre or specialist

dealer for details about how to do this in accordance with the applicable disposal

regulations.

12 Technical data

Approvals

The appliance has E13 certification.

VT100DIG

Ref. no.: 9600000068

Frequency: 2.400–2.483 GHz

Transmission output of transmitter module: 10 mW

Reception delay: < 200 ms

Range: 120 m, free field

Channel raster: 18.9 MHz

Frame rate: max. 30 frames/s

Operating temperature: –20 °C to +60 °C

Operating voltage: 12–30 Vg

Current consumption

Transmitter module (without camera)

Receiver module:

approx. 130 mA

approx. 100 mA

Protection class: IP65

Dimensions (W x H x D) (without antenna): 115 x 110 x 26 mm

Weight: 220 g

13

1622

10R-0412874

VT100DIG-IO-16s.book Seite 18 Montag, 1. August 2016 2:46 14

VT100DIG Erklärung der Symbole

DE

19

Bitte lesen Sie diese Anleitung vor Einbau und Inbetriebnahme sorgfältig durch und

bewahren Sie sie auf. Geben Sie sie im Falle einer Weitergabe des Produktes an den

Nutzer weiter.

Inhaltsverzeichnis

1 Erklärung der Symbole. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

2 Sicherheits- und Einbauhinweise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

3 Lieferumfang . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

4 Bestimmungsgemäßer Gebrauch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

5 Technische Beschreibung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

6 Funkstrecke montieren . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

7 Funkstrecke elektrisch anschließen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

8 System abgleichen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

9 Störungsbeseitigung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

10 Gewährleistung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

11 Entsorgung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

12 Technische Daten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

1 Erklärung der Symbole

!

A

I

WARNUNG!

Sicherheitshinweis: Nichtbeachtung kann zu Tod oder schwerer Verletzung führen.

VORSICHT!

Sicherheitshinweis: Nichtbeachtung kann zu Verletzungen führen.

ACHTUNG!

Nichtbeachtung kann zu Materialschäden führen und die Funktion des Produktes

beeinträchtigen.

HINWEIS

Ergänzende Informationen zur Bedienung des Produktes.

VT100DIG-IO-16s.book Seite 19 Montag, 1. August 2016 2:46 14

Sicherheits- und Einbauhinweise VT100DIG

DE

20

2 Sicherheits- und Einbauhinweise

Der Hersteller übernimmt in folgenden Fällen keine Haftung für Schäden:

• Beschädigungen am Produkt durch mechanische Einflüsse und Überspannungen

• Veränderungen am Produkt ohne ausdrückliche Genehmigung vom Hersteller

• Verwendung für andere als die in der Anleitung beschriebenen Zwecke

Beachten Sie die vom Fahrzeughersteller und vom Kfz-Handwerk vorgeschriebenen

Sicherheitshinweise und Auflagen!

!

WARNUNG!

Unzureichende Leitungsverbindungen können zur Folge haben, dass durch Kurzschluss

• Kabelbrände entstehen,

• der Airbag ausgelöst wird,

• elektronische Steuerungseinrichtungen beschädigt werden,

• elektrische Funktionen ausfallen (Blinker, Bremslicht, Hupe, Zündung, Licht).

A

ACHTUNG!

Klemmen Sie wegen der Kurzschlussgefahr vor Arbeiten an der Fahrzeugelektrik immer

den Minuspol ab.

Bei Fahrzeugen mit Zusatzbatterie müssen Sie an dieser ebenfalls den Minuspol abklem-

men.

Beachten Sie deshalb folgende Hinweise:

• Verwenden Sie bei Arbeiten an den folgenden Leitungen nur isolierte Kabelschuhe, Stecker

und Flachsteckhülsen:

– 30 (Eingang von Batterie Plus direkt)

– 15 (Geschaltetes Plus, hinter Batterie)

– 31 (Rückleitung ab Batterie, Masse)

– L (Blinkerleuchten links)

– R (Blinkerleuchten rechts)

Verwenden Sie keine Lüsterklemmen.

• Verwenden Sie eine Krimpzange zum Verbinden der Kabel.

• Schrauben Sie das Kabel bei Anschlüssen an Leitung 31 (Masse)

– mit Kabelschuh und Zahnscheibe an eine fahrzeugeigene Masseschraube oder

– mit Kabelschuh und Blechschraube an das Karosserieblech.

Achten Sie auf eine gute Masseübertragung!

VT100DIG-IO-16s.book Seite 20 Montag, 1. August 2016 2:46 14

La pagina sta caricando ...

Dometic PERFECTVIEW VT100DIG Istruzioni per l'uso

Questo manuale è adatto anche per

Dometic PERFECTVIEW VT100DIG Istruzioni per l'uso

in altre lingue

Documenti correlati

Altri documenti