Lenco LS-410 Manuale utente

Model: LS-410

User manual - Turntable with 4 speakers built-in

and Bluetooth reception

Gebruikshandleiding - Platenspeler met 4 ingebouwde

luidsprekers en Bluetooth-ontvangst

Bedienungsanleitung - Plattenspieler mit 4 integrierten

Lautsprechern und Bluetooth-Empfang

Manuel de l’utilisateur – Tourne-disque équipé de 4 haut-parleurs intégrés et d’un

récepteur Bluetooth

Manual del usuario - Tocadiscos con 4 altavoces

integrados y recepción por Bluetooth

Руководство по эксплуатации - Проигрыватель с 4 встроенными динамиками и

Bluetooth

Manuale dell'utente – Giradischi con 4 altoparlanti

integrati e ricezione Bluetooth

1

Index

English ..................................................................................................... 2

Nederlands ............................................................................................ 31

Deutsch ................................................................................................. 63

Français ................................................................................................. 95

Español ................................................................................................ 127

Italiano ................................................................................................ 160

Russian................................................................................................192

Version : 3.0

2

English

CAUTION:

Usage of controls or adjustments or performance of procedures other

than those specified herein may result in hazardous radiation

exposure.

PRECAUTIONS BEFORE USE

KEEP THESE INSTRUCTIONS IN MIND:

1. Do not cover or block any ventilation openings. When placing the

device on a shelf, leave 5 cm (2”) free space around the whole

device.

2. Install in accordance with the supplied user manual.

3. Keep the device away from heat sources such as radiators,

heaters, stoves, candles and other heat-generating products or

naked flame. The device can only be used in moderate climates.

Extremely cold or warm environments should be avoided.

Working temperature between 0° and 35°C.

4. Avoid using the device near strong magnetic fields.

5. Electrostatic discharge can disturb normal usage of this device.

If so, simply reset and restart the device following the instruction

manual. During file transmission, please handle with care and

operate in a static-free environment.

6. Warning! Never insert an object into the product through the

vents or openings. High voltage flows through the product and

inserting an object can cause electric shock and/or short circuit

internal parts. For the same reason, do not spill water or liquid on

the product.

7. Do not use in wet or moist areas such as bathrooms, steamy

kitchens or near swimming pools.

8. The device shall not be exposed to dripping or splashing and

make sure that no objects filled with liquids, such as vases, are

placed on or near the apparatus.

3

9. Do not use this device when condensation may occur. When the

unit is used in a warm wet room with damp, water droplets or

condensation may occur inside the unit and the unit may not

function properly; let the unit stand in power OFF for 1 or 2 hours

before turning on the power: the unit should be dry before

getting any power.

10. Although this device is manufactured with the utmost care and

checked several times before leaving the factory, it is still

possible that problems may occur, as with all electrical

appliances. If you notice smoke, an excessive build-up of heat or

any other unexpected phenomena, you should disconnect the

plug from the main power socket immediately.

11. This device must operate on a power source as specified on the

specification label. If you are not sure of the type of power supply

used in your home, consult your dealer or local power company.

12. Keep away from animals. Some animals enjoy biting on power

cords.

13. To clean the device, use a soft dry cloth. Do not use solvents or

petrol based fluids.

To remove severe stains, you may use a damp cloth with dilute

detergent.

14. The supplier is not responsible for damage or lost data caused by

malfunction, misuse, modification of the device or battery

replacement.

15. Do not interrupt the connection when the device is formatting or

transferring files. Otherwise, data may be corrupted or lost.

16. If the unit has USB playback function, the USB memory stick

should be plugged into the unit directly. Don’t use an USB

extension cable because it can cause interference resulting in

failing of data.

17. The rating label has been marked on the bottom or back panel of

the device.

4

18. This device is not intended for use by people (including children)

with physical, sensory or mental disabilities, or a lack of

experience and knowledge, unless they’re under supervision or

have received instructions about the correct use of the device by

the person who is responsible for their safety.

19. This product is intended for non professional use only and not for

commercial or industrial use.

20. Make sure the unit is adjusted to a stable position. Damage

caused by using this product in an unstable position vibrations or

shocks or by failure to follow any other warning or precaution

contained within this user manual will not be covered by

warranty.

21. Never remove the casing of this device.

22. Never place this device on other electrical equipment.

23. Do not allow children access to plastic bags.

24. Only use attachments/accessories specified by the manufacturer.

25. Refer all servicing to qualified service personnel. Servicing is

required when the device has been damaged in any way, such as

the power supply cord or the plug, when liquid has been spilled

or objects have fallen into the device, when the device has been

exposed to rain or moisture, does not operate normally, or has

been dropped.

26. Long exposure to loud sounds from personal music players may

lead to temporary or permanent hearing loss.

27. If the product is delivered with power cable or AC power adaptor:

⚫ If any trouble occur, disconnect the AC power cord and refer

servicing to qualified personnel.

⚫ Don’t step on or pinch the power adaptor. Be very careful,

particularly near the plugs and the cable’s exit point. Do not

place heavy items on the power adaptor, which may

damage it. Keep the entire device out of children’s reach!

When playing with the power cable, they can seriously

injure themselves.

5

⚫ Unplug this device during lightning storms or when unused

for a long period.

⚫ The socket outlet must be installed near the equipment and

must be easily accessible.

⚫ Do not overload ac outlets or extension cords. Overloading

can cause fire or electric shock.

⚫ Devices with class 1 construction should be connected to a

main socket outlet with a protective earthed connection.

⚫ Devices with class 2 construction do not require a earthed

connection.

⚫ Always hold the plug when pulling it out of the main supply

socket. Do not pull the power cord. This can cause a short

circuit.

⚫ Do not use a damaged power cord or plug or a loose outlet.

Doing so may result in fire or electric shock.

28. If the product contains or is delivered with a remote control

containing coin/cell batteries:

Warning:

⚫ “Do not ingest battery, Chemical Burn Hazard” or equivalent

working.

⚫ [The remote control supplied with] This product contains a

coin/button cell battery. If the battery is swallowed, it can

cause severe internal burns in just 2 hours and can lead to

death.

⚫ Keep new and used batteries away from children.

⚫ If the battery compartment does not close securely, stop

using the product and keep it away from children.

⚫ If you think batteries might have been swallowed or placed

inside any part of the body, seek immediate medical

attention.

29. Caution about the use of Batteries:

⚫ Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

6

⚫ Battery cannot be subjected to high or low extreme

temperatures, low air pressure at high altitude during use,

storage or transportation.

⚫ Replacement of a battery with an incorrect type that can

result in an explosion or the leakage of flammable liquid or

gas.

⚫ Disposal of a battery into fire or a hot oven, or mechanically

crushing or cutting of a battery, that can result in an

explosion.

⚫ Leaving a battery in an extremely high temperature

surrounding environment that can result in an explosion or

that leakage of flammable liquid or gas.

⚫ A battery subjected to extremely low air pressure that may

result in an explosion or the leakage of flammable liquid or

gas.

⚫ Attention should be drawn to the environmental aspects of

battery disposal.

INSTALLATION

• Unpack all parts and remove protective material.

• Do not connect the unit to the mains before checking the mains

voltage and before all other connections have been made.

* Those instruction are related only to products using power cable

or AC power adaptor.

7

Product Description

1. DC INPUT Jack

2. Phono & Line Out Switch

3. AUX IN Jack

4. Phono & Aux Out Jacks

5. Lid Hinge

6. Counterweight

7. Tracking Force Dial

8. Tonearm Lift Lever

9. Tonearm Clip

10. Tonearm

11. Volume Control

12. Indicator

13. Speed Selector Button

14. Play/Stop Button

15. ON/OFF/Function Button

16. Stylus Cartridge

17. Turntable platter

18. Turntable spindle

8

Included Items

Before installing the turntable, check the package contents to ensure

all parts below are included and free of visible damage. Please retain

the original packaging materials for exchange or return purposes.

1) Turntable Unit

2) Power Adapter

3) Turntable Lid

4) Slip Mat

5) Platter with Belt

6) Counterweight

7) Cartridge Alignment

Protractor

8) 45 RPM Adapter

9) Instruction Manual

Installing the turntable

. Mount the turntable on a level surface.

. To avoid the effects of vibrations and acoustic pressure, do not

mount the turntable next to items such as speakers.

. The turntable may pick up radio static if placed next to a radio.

Therefore, try to keep the turntable away from radios.

. If the turntable is near equipment (cell phone, etc.) that emits

strong radio waves, noise may occur.

9

Installing the Lid

Insert the hinge pockets of the lid onto the hinges of the turntable.

Turntable Platter and Belt Setup

1. Turn the platter over and check the belt position.

Make sure that the drive

belt is looped in the middle

of the circle. The drive belt

located too high or too low

in this circle may cause the

drive belt to fall off or

speed to be unstable.

2. Set the platter on the spindle.

Make sure the platter is fully seated on the spindle.

10

3. Place the belt on the motor pulley.

Align one of the platter openings with the motor pulley, and while

pulling both ends of the red ribbon that comes attached to the belt,

place the belt on the motor pulley, as per the diagram. When doing

this, be careful not to twist the belt.

4. Remove the red ribbon from the belt.

11

Rotating the Platter

1. Using your hands, slowly rotate the

platter ten times in a clockwise

direction (Figure 1).

2. This step is for resetting the auto

mechanism, getting rid of any twists in

the belt and making sure the belt rides

smoothly along the drive rim on the

underside of the platter.

3. Place the slip mat on top of the platter.

Make sure the logo on the mat is

facing up (Figure 2).

Cartridge Tracking Force Adjustment

The supplied Counterweight is

suitable for cartridges weighing

between 3.0-6.0g.

12

1. Gently push and turn the counterweight

onto the rear of the tonearm (with the dial

facing toward the front of the turntable).

2. Pull the protector straight forward to

remove it.

NOTE: Applying a downward force may

cause the stylus to come off the body. Only

low volume is output if the stylus has come

off, or is about to come off, so refer to

"Replacing the stylus" to reattach the stylus

correctly.

EN

CAREFUL!

3. Remove the tie-wrap and unlock the tonearm.

4. Lower the tonearm lift lever and position the cartridge in the space

between the tonearm rest and platter.

5. Carefully rotate the counterweight until the tonearm achieves a

neutral balance. The tonearm should return to this balanced

position if it is moved up or down. This adjustment must be done

carefully.

13

6. Once the tonearm is correctly balanced, return the tonearm to its

rest. Without moving the position of the counterweight, gently

rotate the tracking force dial until the zero is in line with black

center line on the rear of the tonearm. Check to make sure the

tonearm is still neutrally balanced.

7. Finally, rotate the counterweight and tracking force dial together

counterclockwise (as seen from the front) to adjust the tracking

force according to the cartridge manufacturer's recommendations.

Note: Each mark on the scale represents 0.1g.The recommended

tracking force for the factory-installed cartridge is 3.5g±0.5g. Carefully

rotate the tracking force dial. When "3.5" is centered over the black

line on the top of the tonearm please stop.

Connection to External Speaker with RCA Audio Cable

This turntable includes 4 built-in speakers and a built-in phono

amplifier.

If you wish to use your own amplifier or speakers, please follow the

instructions below:

14

NOTE: In order to achieve the best sound, it is advised to set the

turntable volume to a minimal level. Then the turntable's audio will be

played back through your own amplifier, speakers, etc.

1. Setting pre-amplifier selector switch

This product has a built-in phono amplifier function. You can use

the product even if you do not have a phono amplifier or

connectable equipment with a built-in phono amplifier.

Use the pre-amplifier selector switch to set the output, as shown

below.

Connectable equipment

being used

Position of pre-amplifier

selector switch

Where to connect RCA

audio cable

Device with phono input

PHONO

Phono input jack and

ground (earth) terminal of

connectable equipment

Device without phono

input

LINE

AUX or line input jack of

connectable equipment

NOTE: The RCA Jacks are not designed to be connected directly to the

passive/unpowered speakers on LINE mode. If connected to the

passive speakers, there will be no sound.

2. Connecting the device

15

Align the settings for the pre-amplifier selector switch and

connect the RCA audio cable to an input jack that is

compatible with the connectable equipment you are using

(amplifier, active speakers, etc.).

• The RCA audio cable's red jack is for the right (R) channel, and

the white jack is for the left (L) channel.

16

Main Power Connection

1. Insert the DC plug of the AC adapter cord into the DC INPUT Jack at

the back of the turntable.

2. Plug the AC adapter into a normal power outlet.

NOTE: Do not plug the AC power adapter into a power outlet before all

turntable assembly is completed. Before turning on turntable power,

recheck all connections to make sure they are correct and secure.

Always turn off the turntable before connecting or disconnecting from

power.

Power Management Function

The turntable will automatically power off after 20 minutes of

inactivity.

The indicator light will turn off.

To resume operation, press the ON/OFF button again.

Playing a Record

1. Before playing a record

1.1 Pull the protector straight forward to remove it.

NOTE: Applying a downward force may

cause the stylus to come off the body.

Only low volume is output if the stylus

has come off, or is about to come off,

so refer to "Replacing the stylus" to

reattach the stylus correctly.

1.2 Place the record on the felt mat so that the center hole aligns with

the spindle.

17

2. Turntable Operation

Sufficiently lower the volume of the amplifier and speakers first.

2.1 Connect the included power adapter to the turntable, press the

mode button. The turntable will turn on. The indicator will light

in red.

2.2 Remove the stylus protector from the stylus.

2.3 Place the record on the slip mat.

2.4 Press the Speed Selector button to switch between 33 and

45 RPM speeds according to the type of record.

2.5 Press the START/Stop button once and the platter will play or

pause.

2.6 Unlock the tonearm clip and set the tonearm lift lever to the up

position.

2.7 Position the tonearm over the desired location (groove) on the

record.

2.8 Carefully lower the tonearm on the record by setting the

tonearm lift lever to the down position.

2.9 Turn up the volume of the turntable as needed.

2.10 When you are finished playing the record, raise the tonearm,

return it to rest on the arm clip and long press the mode button

to turn off the turntable.

18

NOTE:

1. If the silent pause time between each track is longer than

3 minute, the platter will stop spinning automatically to avoid

damaging the record. The indicator light will be red. To resume

operation, press the START button.

2. If the felt mat gets dirty, it can easily scratch the record, so remove

the felt mat periodically and wipe off any dust.

3. To prevent the record from scratches and warping, remove it after

use.

4. Do not use a disk stabilizer.

AUX-IN Operation

This turntable includes an auxiliary audio signal input jack for

connecting external audio devices like MP3 players, CD players, and

older, non-dockable iPods so you can listen to your external source

through the turntable's speakers.

1. Use an audio cable (not included) with one 3.5 mm stereo

connection on each end of the cable.

2. Plug one end into the AUX-IN jack on the turntable and the other

end to the Line Out jack of the audio device.

3. Power on the turntable and audio device. The indicator light of

turntable is red.

4. Press the MODE button again, the indicator light of turntable

turns green. It's AUX-IN mode.

5. The volume level can be controlled through the turntable.

Operate all the functions on the auxiliary device as usual.

NOTE:

1. Make sure the tone arm is securely locked to avoid any damage.

2. When you are done, don't forget to turn off the power on the

turntable and your external device.

19

Bluetooth Operation

1. Connect the included power adapter to the turntable and press

the mode button, the indicator will light in red.

2. Press the mode button twice to Bluetooth mode. The indicator

light turns blue and flash quickly. You will hear an activation

sound from the turntable.

3. Turn on the Bluetooth feature of your media device and search

for and select "Lenco LS-410 "to pair the media device and

turntable.

4. Once your media device is successfully paired with the turntable,

the turntable will play a short confirmation sound.

5. Play and stream music from your media device to the turntable.

The indicator light will become solid.

Note: Bluetooth version: 5.0

“This product has a bluetooth reception function, you can not

transmit any bluetooth sound with it: this means that you can receive

wirelessly a bluetooth sound signal from an external source like a

smartphone.”

La pagina sta caricando ...

Lenco LS-410 Manuale utente

Lenco LS-410 Manuale utente

in altre lingue

Documenti correlati

Altri documenti