Audio-Technica AT-LP3WH Manuale utente

AT-LP3

User Manual

Fully Automatic Belt-Drive Turntable

Manuel de l’utilisateur

Tourne-disque à entraînement par courroie

entièrement automatique

Manuel de l’utilisateur

Vollautomatischer, riemenbetriebener

Plattenspieler

Manuale dell’utente

Giradischi con trasmissione a cinghia

totalmente AUTOMATICO

Manual de usuario

Tocadiscos de transmisión por correa

totalmente automático

Manual do Usuário

Toca-discos acionado por correia

totalmente automático

Руководство пользователя

Полностью автоматический проигрыватель

виниловых пластинок с ре менным приводом

1

Introduction

Thank you for purchasing this Audio-Technica product.

Read through this user manual before using the product to ensure its correct use. Also, keep this manual, along with the warranty, for future reference.

This product is only for use in the following countries. Make sure that the operating voltage of the product is correct for the country you live in.

Country list: EU, Russia

Package contents

Make sure that you have all the included items listed below before using this product.

If some items are missing or damaged, contact your local Audio-Technica dealer.

•

Turntable body

•

Rubber mat

•

Dust cover

•

Platter (with drive belt)

•

Counterweight

•

Headshell (AT-HS3) with VM stereo cartridge

(AT91R)

•

Power cable (Use the correct power cable for the country you live in.)

•

User manual (this document)

•

45 RPM adapter

After purchase, we suggest that you save all packaging materials for possible future storage, moving, or shipping.

2

Safety precautions

Important information

Warning:

To prevent fire or shock hazard, do not expose this apparatus to rain or moisture.

Caution:

Do not expose this apparatus to drips or splashes.

To avoid electric shock, do not open the cabinet.

Refer servicing to qualified personnel only.

Do not expose this apparatus to excessive heat such as sunshine, fire

or the like.

Do not subject this apparatus to strong impact.

This apparatus should be located close enough to the AC outlet so that you can easily grasp the power cord plug at any time.

In case of emergency, disconnect the power cord plug of this apparatus quickly.

Do not place any objects filled with liquids, such as vases, on this apparatus.

To prevent fire, do not place any naked flame sources (such as lighted candles) on this apparatus.

Do not install this apparatus in a confined space such as a bookcase or similar unit.

To install this apparatus only in the place where ventilation is good.

Notes on use

Turntable body

•

Do not set and use the product in locations that are considerably hot or humid, dirty, or subject to extreme vibrations.

•

The product should be positioned on a flat, level surface.

Cartridge

•

Attach the provided protector to the cartridge when the product is not in use.

•

Do not touch the stylus of the cartridge with your finger.

•

Do not allow the stylus to bump against the platter, rubber mat, or edge of the record.

3

Part names and functions

Overall diagram

8 9

10

11

12 13

15

14

1

2

3

4

5

6

7

1

45 RPM adapter (shown in receptacle)

Select the platter speed (33-1/3 or 45 RPM).

2

Platter

3

Rubber mat

4

Spindle

5

Dust cover hinge holders

Attachment points for dust cover hinges.

6

Tonearm part

For details, refer to “Tonearm” on p. 4.

7

Size selector

Switch between 12" and 7", according to the size of the record.

8

Platter speed button

Select the platter speed (33-1/3 or 45 RPM).

9

START button

Spins the platter and moves the tonearm.

10

STOP button

Returns the tonearm to its original position and stops the platter.

11

Dust cover

12

Pre-amplifier selector switch

If using an amplifier with a PHONO input jack, set this switch to the

PHONO position. If connecting to the AUX jack of an amplifier, set this

switch to the LINE position.

13

MM (VM)/MC cartridge selector switch

If using an MM (VM) cartridge, set this switch to the MM position. If

using an MC cartridge, set this switch to the MC position.

14

RCA audio cable (with grounding wire)

Connect to PHONO input jack (grounding wire to ground terminal, if

available) or AUX (LINE) input jack of a receiver, amplifier or other

connectable equipment.

15

AC inlet

Insert the power cable here.

4

Part names and functions

Tonearm

1

2

3

5

6

8

4

9

7

1

Counterweight

Balances the tonearm and adjusts to provide the proper tracking force.

2

Tracking force gauge ring

Use to adjust the tracking force.

3

Tonearm lift

Moves the tonearm vertically to and from the face of the record.

4

Tonearm rest

5

Anti-skate control dial

While the record is playing, a force acts on the stylus tip to pull it inward.

This force can be counteracted by setting the same values for anti-skate

and the tracking force.

6

Tonearm lift control lever

Operates the tonearm lift.

7

Tonearm

8

Locking ring

Rotate the ring to the left (counterclockwise) to secure the headshell. To

remove the headshell, rotate the ring to the right.

9

Headshell and cartridge

The cartridge (AT91R) is mounted to the headshell (AT-HS3).

5

Preparation for use

Installing the turntable

•

Mount the product on a level surface.

•

To avoid the effects of vibrations and acoustic pressure, do not mount the

product next to such items as speakers.

•

The product may pick up radio static if placed next to a radio. Therefore, try

to keep the product away from radios.

•

If the product is near equipment (cell phone, etc.) that emits strong radio

waves, noise may occur.

Placing the platter and the rubber mat

This product requires some assembly before using it for the first time.

Do not connect the power cable until assembly is complete.

1. Set the platter on the spindle.

•

Make certain that the platter is fully seated on the spindle.

2. Place the belt on the motor pulley (brass-colored).

•

Align one of the platter openings with the brass motor pulley, and, while pulling

both ends of the red ribbon that comes attached to the belt, place the belt on the

motor pulley, as per the diagram. When doing this, be careful not to twist the

belt.

Belt

Motor pulley

(brass-colored)

Red ribbon

Straight Twisted

3. Remove the red ribbon from the belt.

4. Set the rubber mat on the platter.

•

After setting the rubber mat, put the 45 RPM adapter into the space made for it

on the upper left.

Rubber mat45 RPM adapter

PlatterOpening

Motor pulley

(brass-colored)

Spindle

6

Preparation for use

Assembling the tonearm

1. Insert the headshell into the locking ring.

•

Hold the right and left edges of the headshell so that you do not damage the

stylus or cut the cartridge’s wires.

2. With the headshell inserted, turn the locking ring

counterclockwise (to the left).

3. With the tracking force gauge ring facing forward, attach

the counterweight to the back of the tonearm, and slowly

turn it counterclockwise (to the left).

Tonearm balance and tracking force

In order for the cartridge to pick up sound correctly from the record’s grooves,

the tonearm’s balance and tracking force must be adjusted to fit the

specifications of the cartridge. If the tonearm’s balance and tracking force are

not properly adjusted, the record or the cartridge’s stylus may become damaged.

•

Do not drag the cartridge’s stylus across the record or rubber mat when

adjusting the tonearm’s balance or tracking force. Doing so may damage the

stylus.

Setting tonearm balance

1. Remove the cartridge’s protector.

2. While holding headshell, remove the cable tie used to

secure the tonearm at the time of delivery.

3. While still lightly holding the headshell, turn the

counterweight to adjust the tonearm’s balance.

•

Adjust the balance so that the tonearm is level when you release the headshell.

4. Return the tonearm to the tonearm rest.

Locking ring

Tonearm Counterweight

Adjust so that tonearm is level

7

Preparation for use

Setting tracking force

1. While supporting the counterweight so that it does not

move, turn the tracking force gauge ring so that its “0”

position lines up with the centerline on the back of the

tonearm (the tracking force is not adjusted simply by

turning the tracking force gauge ring).

2. Turn the counterweight and the tracking force gauge

ring together counterclockwise until the centerline value

matches the recommended tracking force value for the

cartridge you are using.

•

Refer to the cartridge maker’s specifications for the recommended tracking force

value.

•

The tracking force value for the cartridge provided with this product is 2.0 g.

Setting the anti-skate adjustment

While the record is playing, a force acts on the stylus tip to pull it inward. This

force can be counteracted by setting the same values for anti-skate and the

tracking force.

1. Adjust the anti-skate control dial to have the same value

as the tracking force value.

•

The tracking force value for the cartridge provided with this product is 2.0 g.

Installing/removing the dust cover

When attaching the dust cover, insert the hinges of the dust cover into the

two dust cover hinge holders on the back of the body. When removing the dust

cover, slowly pull the dust cover out from the dust cover hinge holders.

Setting MM (VM)/MC Cartridge Selector Switch

If using a moving magnet (MM or VM) cartridge, set this switch to the MM

position. If using a moving coil (MC) cartridge, set this switch to the MC

position.

•

This switch is set to the MM position at the time of purchase. This is the

correct setting for the AT91R VM stereo cartridge included with the product.

Setting pre-amplifier selector switch

This product has a built-in phono equalizer function. You can use the product,

even if you do not have a phono amplifier or connectable equipment with a

built-in phono amplifier.

Use the pre-amplifier selector switch to set the output, as shown below.

Connectable

equipment being

used

Position of

pre-amplifier

selector switch

Where to connect

RCA audio cable

Device with phono

input

PHONO Phono input jack and

ground (earth) terminal of

connectable equipment

Device without phono

input

LINE AUX or line input jack of

connectable equipment

PC sound card LINE PC sound card’s line input

jack

*1

An audio adapter (sold separately) may be required to connect the RCA audio cable to

the line input jack of the PC sound card.

Centerline

Tracking force gauge ring

Hinge

8

Preparation for use

Connecting the device

Align the settings for the pre-amplifier selector switch and connect the RCA audio cable to an input jack that is compatible with the connectable equipment you are

using (amplifier, receiver, active speakers, sound card, etc.).

•

The RCA audio cable's red jack is for the right (R) channel, and the white jack is for the left (L) channel.

Rotating the platter

1. Using your hands, rotate the platter ten times.

•

Raise the tonearm lift control lever to lift the tonearm. Slowly rotate the turntable

ten times by hand in the direction of the arrow.

•

You may want to hold the tonearm to prevent it from moving. This step is for

resetting the auto mechanism, getting rid of any twists in the belt and making

sure the belt rides smoothly along the drive rim on the underside of the platter.

Connecting the power cable

This product does not have a power switch. A standby current is always running

through the product, even when it is not being used; disconnect the power cable

plug from the outlet when not using the product for a long period of time.

1. Connect the power cable plug to the outlet.

•

For safety, raise the tonearm by lifting the tonearm lift control lever to the UP

position.

•

Connect the power cable plug to the outlet without removing the cartridge’s

protector. If the platter has rotated, press the STOP button without touching the

tonearm, and then wait until the tonearm returns to its original position.

•

If you play a record immediately after inserting the power cable, the sound that

is played may be garbled. Wait a short time (about 30 seconds) after plugging the

power cable plug into the outlet before playing a record.

*1

Depending on the connectable equipment you are using, a ground

(earth) terminal may be present near the phono input jack. If this is

the case, connect the grounding wire of the RCA audio cable to it.

This will help prevent a low humming noise that might otherwise

be heard during playback.

With PHONO

*1

Without PHONO

To outlet

Connectable equipment

(Amplifier, etc.)

Tonearm

9

Playing a record

Before playing a record

1. Remove the cartridge’s protector.

•

Pull the protector straight forward to remove it.

•

Applying a downward force may cause the stylus to come off the body. Only low

volume is output if the stylus has come off, or is about to come off, so refer to

“Replacing the stylus” on p. 10 to reattach the stylus correctly.

2. Place the record on the rubber mat so that the center

hole aligns with the spindle.

•

If playing a 45 RPM record with a large center hole, attach the 45 RPM adapter

(see the right side of the diagram below).

Automatic operation

Lower the volume of the amplifier, speakers, etc. sufficiently.

1. Select the size with the size selector.

•

Select “12"” for an LP record with a 12" diameter, and “7"” for a 45 RPM record

with a 7" diameter.

2. Press the speed with the platter speed button.

•

Select “33” for a 33-1/3 RPM record, and “45” for a 45 RPM record.

3. Press the START button.

•

Do not bump the product while the record is playing.

•

Do not switch the record size selection while the record is playing. Doing either of

these can cause the product to malfunction.

Manual operation

Lower the volume of the amplifier, speakers, etc. sufficiently.

1. Raise the tonearm by lifting the tonearm lift control lever

to the UP position.

Tonearm lift control lever

2. Position the tonearm over the desired location (groove)

on the record.

3. Lower the tonearm by moving the tonearm lift control

lever to the DOWN position. The tonearm descends

slowly onto the record and play begins.

•

Alternatively, you can skip steps 1 to 3, and use the finger-lift on the headshell to

position the tonearm over the desired location on the record. Carefully lower the

tonearm to the record surface.

•

Do not subject the product to strong impact during playback.

Pausing the record

1. After lowering the volume of the amplifier, speakers, etc.

sufficiently, lift the tonearm with the tonearm lift control

lever.

protector

45 RPM adapter

10

Playing a record

Stopping the record

Once the record has been played until the end, the tonearm automatically

returns to the tonearm rest.

To manually stop the record, do the following.

1. Lower the volume of the amplifier, speakers, etc.

sufficiently.

2. Press the STOP button.

•

Once the record stops playing, the tonearm automatically returns to the tonearm

rest.

3. Remove the record after the platter has come to a

complete stop.

•

When the tonearm reaches the end (center) of the record, it will automatically

lift and return to the tonearm rest. Do not interfere with its motion. Doing so can

cause the product to malfunction. If the tonearm does not lift and return to the

tonearm rest, press the STOP button to complete this operation.

•

If the rubber mat gets dirty, it can easily scratch the record, so remove the

rubber mat periodically and wipe off any dust.

•

To prevent the record from scratches and warping, remove it after use.

•

Do not use a disk stabilizer.

•

Do not use a platter other than the one provided.

•

This product is not intended for DJs. Do not touch the record or the platter while

the record is playing.

Care

Turntable body

•

When the turntable body is dirty or dusty, first disconnect the power cable

plug, and then wipe off the dirt and dust with a soft, dry cloth.

•

Do not use benzenes, thinners, etc.

•

When storing the product for a long time, disconnect the power cable plug

from the outlet and wrap the equipment in plastic; do not allow it to become

damp.

Stylus tip

•

If dirt and grime are stuck to the stylus tip, clean it with a commercially sold

brush.

•

We recommend using a stylus cleaner (sold separately) if the stylus tip is

considerably dirty. Clean the stylus tip by moving the brush from the rear to

the front of the stylus tip.

Replacing the stylus

Removing the stylus

•

In addition to the deterioration of sound quality, records may also be

damaged as the cartridge’s stylus tip wears down.

•

As a rule of thumb, replace the stylus after 300 to 500 hours of use.

•

Be sure to disconnect the product’s power cable plug from the outlet.

1. Release the headshell from the tonearm.

•

Hold the tonearm tightly and then remove the headshell gently.

2. Remove the protector from the cartridge.

3. Remove the stylus by pulling in the direction of the arrow.

Installing a new replacement stylus

1. Mount the new replacement stylus to the cartridge.

2. Mount the protector onto the cartridge.

3. Mount the headshell onto the tonearm.

Engage rear tab first.

11

Replacing a cartridge

Replacing a new cartridge

Refer to the user manual for the cartridge that you will be using if you are

replacing the cartridge (AT91R) included with this product with another,

commercially sold cartridge. After you replace the old cartridge with a new one,

you must readjust the overhang and the tonearm’s balance and tracking force.

1. Release the headshell from the tonearm.

•

Hold the tonearm tightly and then remove the headshell gently.

2. Remove the stylus from the cartridge.

•

Refer to “Removing the stylus” on p. 10.

3. Remove the lead wires.

•

Be careful not to damage the lead wires.

4. Using a commercially sold, non-metallic slotted

screwdriver, remove the installation screws, and then

remove the cartridge from the headshell.

5. Refer to the user manual for the new cartridge for

mounting instructions.

6. Using a commercially sold, non-metallic slotted

screwdriver, tighten the screws in both places, and then

adjust the overhang.

•

Refer to "Adjusting the overhang" on p. 12.

•

After the adjustments are complete, tighten the screws securely.

7. Attach the headshell to the tone arm.

8. Adjust the tonearm balance and tracking force.

•

Refer to “Tonearm balance and tracking force” on p. 6 to perform the

readjustments.

Replacing the belt

•

The belt is a consumable part. Replace the belt if the speed of playback

slows down or irregular rotation occurs. As a rule of thumb, we suggest

replacing the belt once a year.

•

Before replacing the belt, be sure to disconnect the product’s power cable

plug from the outlet.

1. Remove the rubber mat.

2. Remove the platter, turn the platter over, and then

remove the old belt.

•

Place your thumbs in the openings and pull up strongly.

3. Place the new belt around the inner circle.

•

Be careful not to twist the belt while doing this.

4. Attach the platter.

•

Align one of the openings with the position of the motor pulley (brass-colored).

5. Place the belt on the motor pulley (brass-colored).

•

Grasp the belt that was attached in step 3 and, while pulling it, place it on the

brass motor pulley.

Installation screws

Plastic washers

Nuts

Motor pulley (brass-colored)

Opening

Place the belt

Motor pulley (brass-colored)

Belt

12

Replacing the belt

6. Using your hands, rotate the platter ten times.

•

Raise the tonearm lift control lever to lift the tonearm. Slowly rotate the turntable

ten times by hand in the direction of the arrow.

When the turntable is moved

Using the product's original packing materials, wrap the turntable in the

reverse order from when you unwrapped it. If you do not have the packaging

materials, take the following measures:

•

After disconnecting the power cable plug from the outlet, remove the rubber

mat and platter, and then wrap them so that they do not get damaged.

•

Use a string or something similar to tie the tonearm to the rest so that it

does not move.

•

Remove the counterweight.

•

Remove the headshell from the tonearm with the protector attached to the

cartridge, and then wrap the entire headshell assembly so that it does not

get damaged.

•

Wrap the turntable body with paper or a soft cloth so that it does not get

damaged.

Adjusting the overhang

The position of the cartridge must be accurately determined (adjusting the

overhang) when mounting a cartridge or headshell other than the one provided.

1. Mount the cartridge so it is parallel to the headshell.

•

Match up the positions of the cartridge and headshell to the figure below and

mount the cartridge so it is parallel to the headshell.

2. Mount the cartridge it is perpendicular to the top of the

headshell.

Front of headshell

This illustration represents the actual size.

Place the headshell on the figure below, and then adjust the stylus tip of

the new cartridge along the lines for the "Stylus tip" of the cartridge.

Overhang adjustment guide

45.0 mm

Stylus tip

Underside of headshell

13

Troubleshooting

Problem Solution

The platter does not spin.

•

Is the power cable plug connected to the outlet? Connect the power cable plug to the outlet.

•

Has the belt slipped from the platter? Correctly place the belt on the platter.

•

Is the belt placed on the motor pulley? Check that the belt is placed on the motor pulley (brass-colored) correctly.

•

Has the belt been damaged? Replace it with a new belt.

The platter spins, but there is no

sound or the volume is not loud

enough.

•

Are the function settings and input for connected equipment (amplifier, etc.) selected correctly? Check whether the

settings for the connected equipment are correct.

•

Is the stylus damaged? Check the stylus and replace it, if necessary.

•

Is the stylus placed correctly on the body of the cartridge? Check the cartridge and adjust it, if necessary.

•

Are the setting positions for the pre-amplifier selector switch correct? Check that the pre-amplifier settings are

correct, noting the following common problems and their causes:

– If there is no sound, or if the volume is not loud enough, the product is set to the “PHONO” position and connected

to the amplifier’s AUX/LINE input.

– If the volume is too loud or is distorted, the product is set to the “LINE” position, and the connectable equipment is

connected to the PHONO input.

•

Is the tracking force set too heavy? Adjust the tracking force.

The stylus skips.

•

Is the tracking force set too light? Adjust the tracking force.

•

Is the anti-skate set improperly? Verify anti-skate is set for same value as cartridge tracking force.

•

Is the record warped? Check the record.

•

Is the record scratched? Check the record.

There is howling.

•

Is the product picking up excessive vibrations from the floor, surfaces of the walls, or nearby speakers? Decrease the

vibrations or mount the product on a surface that is not subject to the effects of vibrations.

•

Is the product mounted on an unstable surface? Check whether the surface on which the product is mounted is suitable.

There is noise when the record is

playing.

•

Is there dust on the cartridge’s stylus tip? If dust is stuck to the stylus tip, clean it with a commercially sold brush.

The sound when the record is playing

is either too fast or too slow.

•

Are the speed settings for this product correct? Use the platter speed button to select the correct speed for the type

of record being played.

Playback speed slows down or there

is irregular rotation.

•

Is the belt stretched out? Replace it with a new belt.

Hum is heard during playback.

•

Is the ground line connected correctly? Make sure the ground line is properly connected.

•

Is the headshell attached to the tonearm firmly? Make sure the locking ring is tight.

Dimensions

435

353

(Unit: mm)

128

14

Specifications

Turntable specifications

Type 2-Speed, fully automatic operation

Motor DC motor

Drive method Belt drive

Speeds 33-1/3 RPM, 45 RPM

Turntable platter Die-cast aluminium

Wow and flutter < 0.2 % WRMS (33 RPM) at 3 kHz

Signal-to-noise ratio > 60 dB

Outputs levels

“PHONO”

“LINE (MM)”

3.5 mV nominal at 1 kHz, 5 cm/sec

220 mV nominal at 1 kHz, 5 cm/sec

Phono Pre-amp gain (MM)

Phono Pre-amp gain (MC)

36 dB nominal, RIAA equalized

56 dB nominal, RIAA equalized

Tonearm specifications

Type Static balanced straight shaped w/soft

damping control

Effective length 221.5 mm

Overhang 19 mm

Maximum tracking error angle Less than 3°

Stylus pressure adjustment range 1 to 4 g

Applicable cartridge weight range

(including headshell)

14.5 to 20 g

Cartridge and headshell specifications

Cartridge Model AT91R

Cartridge Type VM Dual Magnet

Recommended load impedance 47,000 ohms

Output voltage 3.5 mV (mV at 1 kHz, 5 cm/sec)

Stylus 0.6 mil bonded conical

Cantilever Aluminum pipe

Tracking force range 1.5 to 2.5 g (standard 2.0 g)

Cartridge weight 5.0 g

Headshell model AT-HS3

Headshell weight 11.1 g

Headshell overhang adjustment 8 mm

General specifications

Power supply requirements 220 to 240 V / 50, 60 Hz

Power consumption 2 W

Dimensions 435 mm (17.13")×353 mm (13.90")×

128 mm (5.04")

(W×D×H)

Weight 5.2 kg (11.46 lbs)

Accessories included Rubber mat, Dust cover, Platter (with

drive belt), Counterweight, Headshell

(AT-HS3) with VM stereo cartridge

(AT91R), 45 RPM adapter, Power cable*

Replacement stylus (sold

separately)

ATN91R

Replacement headshell (sold

separately)

AT-HS3

Replacement belt (sold separately) AT-LP3 exclusive belt

*Use the correct power cable for the country you live in.

Specifications are subject to change without notice due to improvements.

1

Introduction

Nous vous remercions d’avoir fait l’acquisition de ce produit Audio-Technica.

Avant utilisation, merci de lire attentivement ce manuel pour vous assurer du bon usage du produit. De meme, veuillez conserver ce manuel ainsi que la garantie

pour consultations ultérieures.

Ce produit n’est destiné qu’à une utilisation dans les pays suivants. Veillez à ce que la tension d’utilisation du produit corresponde à celle utilisée dans le pays où

vous vivez.

Liste des pays : Union européenne, Russie

Contenu de l’emballage

Assurez-vous que tous les articles inclus répertoriés sur la liste ci-dessous soient présents avant d’utiliser le produit.

Si certains éléments sont manquants ou endommagés, contactez votre distributeur local Audio-Technica.

•

Corps du plateau de la platine

•

Tapis amortissant en caoutchouc

•

Couvercle anti-poussière

•

Plateau (avec courroie d’entraînement)

•

Contrepoids

•

Porte-cellule (AT-HS3) avec cellule stéréo VM

(AT91R)

•

Câble d’alimentation (Utilisez le câble d’alimentation adéquat pour le pays dans lequel où vous

vivez.)

•

Manuel d’utilisation (ce document)

•

Adaptateur 45 tours

Après l’achat, nous vous suggérons de conserver tous les emballages pour un éventuel stockage, déménagement, ou transport.

2

Consignes de sécurité

Informations importantes

Avertissement:

Pour éviter tout risque de choc électrique ou d’incendie, n’exposez pas cet appareil à la pluie ou à l’humidité.

Mise en garde:

Protégez cet appareil des projections et des gouttes d’eau.

Pour éviter tout risque de choc électrique, n’ouvrez pas le boîtier.

Confiez tous travaux d’entretien à un technicien qualifié.

N’exposez pas cet équipement à des températures excessives, telles que celles de la lumière directe du soleil, d’une flamme ou autres.

Ne soumettez pas cet équipement à de forts impacts.

Placez l’appareil à proximité d’une prise de courant pour une utilisation aisée du câble d’alimentation.

En cas d’urgence, déconnectez immédiatement la prise du câble d’alimentation de l’appareil.

Ne placez pas d’objets remplis de liquides, tels que des vases, sur l’appareil.

Pour éviter tout risque d’incendie, ne placez pas de flammes nues (telles que des bougies allumées) sur l’appareil.

N’installez pas cet appareil dans un espace confiné tel qu’une étagère ou un endroit similaire.

Installez cet appareil uniquement dans des endroits avec une bonne ventilation.

Remarques d’utilisation

Corps du plateau de la platine

•

Ne placez pas et n’utilisez pas le produit dans des endroits soumis à de fortes chaleurs ou une humidité élevée, très sales ou soumis à des vibrations extrêmes.

•

Le produit doit être placé sur une surface plane et lisse.

Cellule

•

Fixez la protection fournie sur la cellule lorsque le produit n’est pas utilisé.

•

Ne touchez pas la pointe de lecture de la cellule avec votre doigt.

•

Empêchez la pointe de lecture de percuter le plateau, le tapis amortissant en caoutchouc ou le bord du disque.

3

Noms des pièces et fonctions

Schéma de l’ensemble

8 9

10

11

12 13

15

14

1

2

3

4

5

6

7

1

Adaptateur 45 tours (affiché dans le réceptacle)

Sélectionnez la vitesse du plateau (33-1/3 ou 45 tours).

2

Plateau

3

Tapis amortissant en caoutchouc

4

Axe

5

Supports de charnières du couvercle anti-poussière

Points de fixation pour les charnières du couvercle anti-poussière.

6

Bras de lecture

Pour plus de détails, reportez-vous à la section “Bras de lecture” en p. 4.

7

Sélecteur de taille

Permuter entre 12" et 7", en fonction de la taille du disque.

8

Bouton de vitesse du plateau

Sélectionnez la vitesse du plateau (33-1/3 ou 45 tours).

9

Bouton START

Fait tourner le plateau et déplace le bras de lecture.

10

Bouton STOP

Replace le bras de lecture dans sa position d’origine et arrête le plateau.

11

Couvercle anti-poussière

12

Sélecteur de préamplificateur

Si vous utilisez un amplificateur avec une prise entrée PHONO, placez le

sélecteur en position PHONO. En cas de connexion d’un amplificateur à la

prise AUX, placez ce sélecteur sur la position LINE.

13

Sélecteur de cellule MM (VM)/MC

Si vous utilisez une cellule MM (VM), placez ce sélecteur en position

MM. Si vous utilisez une cellule MC, placez ce sélecteur en position MC.

14

Câble audio RCA (avec câble de mise à la terre)

Raccordez la prise d’entrée PHONO (câble de mise à la terre à la borne

de mise à la terre, si disponible) ou la prise d’entrée AUX (LINE) d’un

récepteur, amplificateur ou autre équipement connecté.

15

Entrée d’alimentation

Insérez le câble d’alimentation ici.

4

Noms des pièces et fonctions

Bras de lecture

1

2

3

5

6

8

4

9

7

1

Contrepoids

Equilibre le bras de lecture et permet un réglage pour obtenir la force

d’appui adéquate.

2

Bague de réglage de la force d’appui

Utilisez pour régler la force d’appui.

3

Porte-bras de lecture

Déplace le bras de lecture verticalement vers et depuis la face du disque.

4

Pose-bras de lecture

5

Cadran de contrôle anti-skating

Pendant la lecture du disque, une force agit sur la pointe de lecture pour

la tirer vers l’intérieur. Cette force peut être contre-balancée en réglant

les mêmes valeurs pour la force anti-skating et la force d’appui.

6

Levier de commande de levage du bras de lecture

Soulève le bras de lecture.

7

Bras de lecture

8

Bague de verrouillage

Tournez la bague vers la gauche (dans le sens anti-horaire) pour fixer le

porte-cellule. Pour enlever le porte-cellule, tournez la bague vers la droite.

9

Porte-cellule et cellule

La cellule (AT91R) est montée sur le porte-cellule (AT-HS3).

5

Préparation pour l’utilisation

Installation de la platine

•

Montez le produit sur une surface plane.

•

Pour éviter les effets de vibrations et la pression acoustique, ne montez pas

le produit à côté d’éléments tels que des haut-parleurs.

•

Le produit peut percevoir des parasites s’il est placé à côté d’une radio. Par

conséquent, essayez de garder le produit éloigné des radios.

•

Si le produit est proche d’équipements (téléphone portable, etc.) qui

émettent de fortes perturbations de radio, des bruits parasites peuvent

survenir.

Placement du plateau et du tapis amortissant

en caoutchouc

Ce produit nécessite un peu de montage avant de l’utiliser pour la première

fois.

Ne connectez pas le câble d’alimentation jusqu’à ce que le montage soit

terminé.

1. Placez le plateau sur l’axe.

•

Assurez-vous que le plateau est correctement installé sur l’axe.

2. Placez la courroie sur la poulie du moteur (laiton coloré).

•

Alignez une des ouvertures du plateau avec la poulie du moteur en laiton, et, tout

en tirant les deux extrémités de la languette rouge qui est fixée sur la courroie,

placez la courroie sur la poulie du moteur, selon le schéma. Tout en effectuant

cette opération, veillez à ne pas tordre la courroie.

Courroie

Poulie de moteur

(laiton coloré)

Languette rouge

Droite Tordue

3. Déposez la languette rouge de la courroie.

4. Placez le tapis amortissant en caoutchouc sur le plateau.

•

Après avoir placé le tapis amortissant en caoutchouc, placez l’adaptateur 45 tours

dans l’espace prévu à cet effet dans le coin supérieur gauche.

Tapis amortissant en caoutchoucAdaptateur 45 tours

PlateauOuverture

Poulie de moteur

(laiton coloré)

Axe

La pagina sta caricando ...

Audio-Technica AT-LP3WH Manuale utente

Questo manuale è adatto anche per

Audio-Technica AT-LP3WH Manuale utente

in altre lingue

Documenti correlati

Altri documenti