Yamaha RX-V559 Manuale del proprietario

YAMAHA ELECTRONICS CORPORATION, USA

6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD.

135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H.

SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A.

RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD.

YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND

YAMAHA SCANDINAVIA A.B.

J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD.

17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

©

RX-V559

Printed in Malaysia WG73470

RX-V559

AV Receiver

Ampli-tuner audio-vidéo

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

GEBRUIKSAANWIJZING

ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ

G

RX-V559_G_cv.fm Page 1 Tuesday, November 22, 2005 3:43 PM

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry, clean

place – away from direct sunlight, heat sources, vibration,

dust, moisture, and/or cold. Allow ventilation space of at

least 30 cm on the top, 20 cm on the left and right, and 20

cm on the back of this unit.

3 Locate this unit away from other electrical appliances,

motors, or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in a environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign object may fall onto

this unit and/or this unit may be exposed to liquid dripping

or splashing. On the top of this unit, do not place:

– other components, as they may cause damage and/or

discoloration on the surface of this unit.

– burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– containers with liquid in them, as they may fall and

liquid may cause electrical shock to the user and/or

damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature

inside this unit rises, it may cause fire, damage to this unit,

and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections

are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cord.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and

may cause fire, damage to this unit, and/or personal injury.

YAMAHA will not be held responsible for any damage

resulting from use of this unit with a voltage other than

specified.

13 To prevent damage by lightning, keep the power cable and

outdoor antennas disconnected from a wall outlet or this unit

during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact qualified

YAMAHA service personnel when any service is needed.

The cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time

(i.e. vacation), disconnect the AC power plug from the wall

outlet.

16 Install this unit near the AC wall outlet where the power

cable plug can be reached easily.

17 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit is

faulty.

18 Before moving this unit, press MASTER ON/OFF to release

it outward to the OFF position to turn off this unit, and then

disconnect the power cable from the AC wall outlet.

19 VOLTAGE SELECTOR (Asia and General models only)

The VOLTAGE SELECTOR on the rear panel of this unit

must be set for your local main voltage BEFORE plugging

into the AC wall outlet. Voltages are:

Asia model ............................ 220/230–240 V AC, 50/60 Hz

General model ........ 110/120/220/230–240 V AC, 50/60 Hz

■ For U.K. customers

If the socket outlets in the home are not suitable for the

plug supplied with this appliance, it should be cut off and

an appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

The plug severed from the mains lead must be destroyed, as a

plug with bared flexible cord is hazardous if engaged in a live

socket outlet.

■ Special Instructions for U.K. Model

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN

OR MOISTURE.

This unit is not disconnected from the AC power

source as long as it is connected to the wall outlet, even

if this unit itself is turned off. In this state, this unit is

designed to consume a very small quantity of power.

Note

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured

markings identifying the terminals in your plug,

proceed as follows:

The wire which is coloured BLUE must be connected

to the terminal which is marked with the letter N or

coloured BLACK. The wire which is coloured

BROWN must be connected to the terminal which is

marked with the letter L or coloured RED.

Making sure that neither core is connected to the earth

terminal of the three pin plug.

1

PREPARATIONINTRODUCTION

BASIC

OPERATION

SOUND FIELD

PROGRAMS

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

English

FEATURES............................................................. 2

GETTING STARTED............................................ 3

Supplied accessories .................................................. 3

Installing batteries in the remote control ................... 3

CONTROLS AND FUNCTIONS ......................... 4

Front panel ................................................................. 4

Remote control........................................................... 6

Front panel display .................................................... 9

Rear panel ................................................................ 11

CONNECTIONS .................................................. 12

Placing speakers....................................................... 12

Connecting speakers ................................................ 13

Information on jacks and cable plugs ...................... 16

Audio and video signal flow.................................... 17

Connecting a TV...................................................... 18

Connecting a DVD player, a DVD recorder,

a VCR or an STB................................................. 19

Connecting a CD player, an MD player

or a tape deck....................................................... 21

Connecting a YAMAHA iPod universal dock ........ 22

Connecting a multi-format player

or an external decoder ......................................... 23

Connecting a game console, a video camera

or a portable audio player.................................... 23

Connecting the FM and AM antennas ..................... 24

Connecting the power cable..................................... 26

Setting the speaker impedance................................. 27

Turning on and off the power .................................. 28

BASIC SETUP ...................................................... 29

PLAYBACK.......................................................... 32

USING AUDIO FEATURES............................... 34

Using SILENT CINEMA ........................................ 34

Muting the audio output........................................... 34

Selecting the night listening mode........................... 34

Selecting the input mode ......................................... 35

Using the sleep timer ............................................... 35

Adjusting the speaker level...................................... 36

Selecting the Compressed Music

Enhancer mode .................................................... 37

Selecting the MULTI CH INPUT component......... 38

Enjoying multi-channel sources

in 2-channel stereo............................................... 39

Enjoying unprocessed input sources........................ 39

Enjoying pure hi-fi stereo sound.............................. 39

USING VIDEO FEATURES ............................... 40

Displaying the input source information ................. 40

Selecting the OSD mode.......................................... 41

Playing video sources in the background ................ 41

ENJOYING SURROUND SOUND .................... 42

Enjoying multi-channel sources in surround ........... 42

Enjoying 2-channel sources in surround.................. 43

Using Virtual CINEMA DSP .................................. 44

RECORDING........................................................45

FM/AM TUNING..................................................46

Automatic tuning ..................................................... 46

Manual tuning.......................................................... 47

Automatic preset tuning........................................... 48

Manual preset tuning ............................................... 49

Selecting preset stations........................................... 50

Exchanging preset stations ...................................... 51

RADIO DATA SYSTEM TUNING

(U.K. AND EUROPE MODELS ONLY)........53

Selecting the Radio Data System program .............. 53

Using the Radio Data System station network ........ 54

Displaying the Radio Data System information ...... 55

SOUND FIELD PROGRAMS .............................57

Selecting sound field programs ............................... 57

Sound field program descriptions............................ 58

Changing sound field parameter settings................. 60

Sound field program speaker layouts ...................... 66

SET MENU ............................................................69

Using SET MENU................................................... 71

1 SOUND MENU.................................................... 72

2 INPUT MENU...................................................... 77

3 OPTION MENU................................................... 79

ADVANCED SETUP............................................82

REMOTE CONTROL FEATURES ...................84

Controlling this unit, a TV,

or other components ............................................ 84

Setting the remote control code ............................... 86

Setting library codes ................................................ 87

Resetting all remote control codes........................... 88

USING MULTI-ZONE CONFIGURATION.....89

Connecting Zone 2................................................... 89

Controlling Zone 2................................................... 90

USING iPod® ........................................................92

Setting the remote control code ............................... 92

Controlling iPod ...................................................... 92

RESETTING THE SYSTEM...............................94

TROUBLESHOOTING .......................................95

GLOSSARY.........................................................100

Audio information ................................................. 100

Video information.................................................. 101

Sound field program information .......................... 102

SPECIFICATIONS.............................................103

CONTENTS

INTRODUCTION

PREPARATION

BASIC OPERATION

SOUND FIELD PROGRAMS

ADVANCED OPERATION

ADDITIONAL INFORMATION

FEATURES

2

Built-in 6-channel power amplifier

◆ Minimum RMS output power

(0.06% THD, 20 Hz to 20 kHz, 8 Ω)

Front: 95 W + 95 W

Center: 95 W

Surround: 95 W + 95 W

Surround back: 95 W

Sound field programs

◆ Proprietary YAMAHA technology for the creation of sound

fields

◆ Dolby Digital/Dolby Digital EX decoder

◆ DTS/DTS-ES Matrix 6.1, Discrete 6.1, DTS Neo:6, DTS 96/

24 decoder

◆ Dolby Pro Logic/Dolby Pro Logic II/Dolby Pro Logic IIx

decoder

◆ Virtual CINEMA DSP

◆ SILENT CINEMA

™

Sophisticated AM/FM tuner

◆ 40-station random and direct preset tuning

◆ Automatic preset tuning

◆ Preset station shifting capability (preset editing)

Radio Data System

(U.K. and Europe models only)

◆ Radio Data System tuning capability

iPod controlling capability

◆ DOCK terminal to connect a YAMAHA iPod universal dock

(such as YDS-10 sold separately), which supports iPod (Click

and Wheel), iPod nano, and iPod mini

Other features

◆ 192-kHz/24-bit D/A converter

◆ OSD (on-screen display) menus that allow you to optimize

this unit to suit your individual audiovisual system

◆ 6 additional input jacks for discrete multi-channel input

◆ S-video signal input/output capability

◆ Component video input/output capability

(3 COMPONENT VIDEO INs and 1 MONITOR OUT)

◆ Digital video signal conversion (composite video ↔ S-video

→ component video) capability for monitor out

◆ Optical and coaxial digital audio signal jacks

◆ Sleep timer

◆ Cinema and music night listening modes

◆ Remote control with preset remote control codes,

backlighting input selector buttons, and an iPod (stationed in a

YAMAHA iPod universal dock connected to the DOCK

terminal) controlling capability

◆ Zone 2 custom installation facility

◆ Zone switching capability between the main zone and Zone 2

using ZONE CONTROL

◆ PORTABLE mini analog input jack on the front panel for a

portable audio player

◆ Compressed Music Enhancer mode to improve the sound

quality of compression artifacts (such as the MP3 format) to

that of a high-quality stereo

• y indicates a tip for your operation.

• Some operations can be performed by using either the buttons on the front panel or the ones on the remote control. In case the button

names differ between the front panel and the remote control, the button name on the remote control is given in parentheses.

• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In

case of differences between the manual and product, the product has priority.

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, and the double-D symbol are trademarks

of Dolby Laboratories.

Manufactured under license from Digital Theater Systems, Inc.

“DTS”, “DTS-ES”, “NEO:6”, and “DTS 96/24” are trademarks

“iPod” is a trademark of Apple Computer, Inc., registered in the

U.S. and other countries.

“SILENT CINEMA” is a trademark of YAMAHA

CORPORATION.

FEATURES

Notes

iPod

®

GETTING STARTED

3

INTRODUCTION

English

Check that you received all of the following parts.

1 Take off the battery compartment cover.

2 Insert the two supplied batteries

(AA, R6, UM-3) according to the polarity

markings (+ and –) on the inside of the

battery compartment.

3 Snap the battery compartment cover back

into place.

• Change all of the batteries if you notice the following

conditions:

– the operation range of the remote control decreases.

– the TRANSMIT indicator does not flash or its light becomes

dim.

• Do not use an old battery together with a new one.

• Do not use different types of batteries (such as alkaline and

manganese batteries) together. Read the packaging carefully as

these different types of batteries may have the same shape and

color.

• If the batteries have leaked, dispose of them immediately. Avoid

touching the leaked material or letting it come into contact with

clothing, etc. Clean the battery compartment thoroughly before

installing new batteries.

• Do not throw away batteries with general house waste; dispose

of them correctly in accordance with your local regulations.

• If the remote control is without batteries for more than 2

minutes, or if exhausted batteries remain in the remote control,

the contents of the memory may be cleared. When the memory

is cleared, insert new batteries, set up the remote control code

and program any acquired functions that may have been

cleared.

GETTING STARTED

Supplied accessories

Installing batteries in the remote control

TV MUTE TV INPUT

MUTE

AMP

SOURCE

TV

MENUTITLE

SET MENU

LEVEL

DISPLAYRETURN

BAND

SRCH MODE

DAB MEMORY

A/B/C/D/E

ENTER

PRESET/CH

REC

AUDIO

DISC SKIP

STEREO

1

EFFECT

VOLUME

TV VOL TV CH

TRANSMITCODE SET

STANDBY

POWER

POWERPOWER

CD

AVTV

MULTI CH IN

SLEEP

CD-R

DVD DTV

MD

CBL

TUNER

V-AU X DVR

STANDARD

5

SPEAKERS

9

MUSIC

2

SELECT

6

ENHANCER

0

ENTERTAIN

3

EXTD SUR.

7

NIGHT

10

MOVIE

4

DIRECT ST.

8

STRAIGHT

ENT.

FREQ/TEXT EONSTARTPTY SEEKMODE

Remote control

Batteries (2)

(AA, R6, UM-3)

Indoor FM antenna

(U.S.A., Canada, China, Asia

and General models)

AM loop antenna

75-ohm/300-ohm antenna

adapter (U.K. model only)

Indoor FM antenna

(U.K., Europe, Australia

and Korea models)

1

3

2

Notes

CONTROLS AND FUNCTIONS

4

1 MASTER ON/OFF

Turns on or off this unit (see page 28).

2 MAIN ZONE ON/OFF

Turns on the main zone or sets it to the standby mode

(see page 28).

• In the standby mode, this unit consumes a small amount of

power in order to receive infrared signals from the remote

control.

• When you turn on this unit, there will be a 4 to 5-second delay

before this unit can reproduce sound.

• This button is operational only when MASTER ON/OFF is

pressed inward to the ON position.

3 Remote control sensor

Receives signals from the remote control (see page 8).

4 Front panel display

Shows information about the operational status of this unit

(see page 9).

5 A/B/C/D/E, NEXT

• Selects one of the 5 preset station groups (A to E) when

“TUNER” is selected as the input source (see page 46).

• Selects the speaker channel whose output level you

want to adjust when “TUNER” is not selected as the

input source (see page 36).

6 PRESET/TUNING l / h, LEVEL +/–

• Selects one of the 8 preset station numbers (1 to 8)

when “TUNER” is selected as the input source. The

colon (:) is displayed in the front panel display (see

page 46).

• Selects the tuning frequency when “TUNER” is

selected as the input source. The colon (:) is not

displayed in the front panel display (see page 46).

• Adjusts the level of the speaker channel selected using

NEXT when “TUNER” is not selected as the input

source (see page 36).

7 MEMORY (MAN’L/AUTO FM)

Stores a preset station in the memory. Hold down this

button for more than 3 seconds to start automatic preset

tuning (see page 48).

CONTROLS AND FUNCTIONS

Front panel

ZONE 2

ON/OFF

ZONE

CONTROL

VIDEO PORTABLEL AUDIO R

NEXTEDIT

EFFECT

MEMORY

FM/AM

PRESET/TUNING

A/B/C/D/E

PROGRAM

l PRESET/TUNING h

TUNING MODE

INPUT MODETONE CONTROLSTRAIGHT

SPEAKERSPHONES

MAIN ZONE

MASTER

SILENT CINEMA

BA

MULTI CH

INPUT

VOLUME

VIDEO AUX

INPUT

ON OFF

LEVEL

MAN'L/AUTO FM

AUTO/MAN'L

ON/OFF

3145687

IJKGFD

A

L

BC

2

EH

90

Notes

CONTROLS AND FUNCTIONS

5

INTRODUCTION

English

8 TUNING MODE (AUTO/MAN’L)

Switches between automatic tuning (the AUTO indicator

is turned on) and manual tuning (the AUTO indicator is

turned off) (see page 46).

9 ZONE 2 ON/OFF

Turns on Zone 2 or sets it to the standby mode

(see page 90).

This button is operational only when MASTER ON/OFF is

pressed inward to the ON position.

0 ZONE CONTROL

Switches the zone you want to control between the main

zone and Zone 2 (see page 90).

y

When Zone 2 is selected, the ZONE2 indicator flashes in the front

panel display for approximately 5 seconds. While the indicator is

flashing, perform the desired operation.

A VOLUME

Controls the output level of all audio channels.

y

This does not affect the AUDIO OUT (REC) level.

B PHONES (SILENT CINEMA) jack

Outputs audio signals for private listening with

headphones (see page 34).

• When you connect headphones, no signals are output at the

SUBWOOFER OUTPUT jack or the speaker terminals.

• All Dolby Digital and DTS audio signals are mixed down to the

left and right headphone channels.

C SPEAKERS A/B

Turns on or off the set of front speakers connected to the

FRONT A and/or B terminals on the rear panel each time

the corresponding button is pressed.

D PRESET/TUNING, EDIT

• Switches the function of PRESET/TUNING l / h

between selecting preset station numbers and selecting

the tuning frequency.

• Edits the assignments of preset stations (see page 51).

E STRAIGHT (EFFECT)

Turns the sound field programs off or on. When the

“STRAIGHT” mode is selected, 2-channel or multi-

channel input signals are output directly from their

respective speakers without effect processing

(see page 39).

F FM/AM

Switches the reception band between FM and AM when

“TUNER” is selected as the input source (see page 46).

G PROGRAM selector

Selects sound field programs or adjusts the bass/treble

balance in conjunction with TONE CONTROL (see

page 33).

H TONE CONTROL

Adjusts the bass/treble balance of the front left and right

speakers in conjunction with the PROGRAM selector

(see page 33).

I INPUT MODE

Selects either digital or analog input signals exclusively or

sets this unit to automatically detect the type of input

signals and select the corresponding input signals when

one component is connected via both digital and analog

connections (see page 35).

J INPUT selector

Selects the desired input source.

K MULTI CH INPUT

Selects the component connected to the MULTI CH

INPUT jacks as the input source (see page 38).

The input source connected to the MULTI CH INPUT jacks takes

priority over the source selected with the INPUT selector on the

front panel (or the input selector buttons on the remote control).

L VIDEO AUX jacks

Input audio and video signals from a portable external

source such as a game console, a video camera or a

portable audio player (see page 23).

y

To reproduce the source signals input at these jacks, select

“V-AUX” as the input source.

• The audio signals input at the PORTABLE mini jack take

priority over the ones input at the AUDIO L/R jacks.

• The audio signals input at the DOCK terminal on the rear panel

take priority over the ones input at the VIDEO AUX jacks.

Note

Notes

Note

Notes

CONTROLS AND FUNCTIONS

6

This section describes the function of each control on the

remote control used to control this unit. To operate other

components, see “REMOTE CONTROL FEATURES” on

page 84.

The operation mode of the remote control buttons in the shaded

areas below depends on the component selector switch position.

Set the component selector switch to AMP to control this unit. To

control the TUNER functions, set the component selector switch

to SOURCE and then press TUNER to select “TUNER” as the

input source.

■ Controlling this unit

Set the component selector switch to AMP to control this

unit.

1 Infrared window

Outputs infrared control signals. Aim this window at the

component you want to operate (see page 8).

2 CODE SET

Use to set up remote control codes (see page 86).

3 Input selector buttons

Select the input source you want to control.

The corresponding input selector button for the currently selected

input source lights up for approximately 5 seconds after you press

any buttons on the remote control, showing which source

component is currently being operated.

4 Sound field program selector buttons

Select sound field programs (see page 57).

– Use SELECT to play back 2-channel sources in

surround (see page 43).

– Use EXTD SUR. to switch between 5.1 and

6.1-channel playback of multi-channel sources

(see page 42).

– Use DIRECT ST. to play back 2-channel sources in hi-

fi stereo sound (see page 39).

5 SPEAKERS

Turns on or off the set of front speakers connected to the

FRONT A and/or B terminals on the rear panel. Press this

button repeatedly to toggle as follows:

6 ENHANCER

Turns on or off the Compressed Music Enhancer mode

(see page 37).

7 LEVEL

Selects the speaker channel to be adjusted and sets the

output level (see page 36).

8 Cursor buttons u / d / j / i, ENTER

Select and adjust the sound field program parameters or

the “SET MENU” parameters.

9 RETURN

Returns to the previous menu level when adjusting the

“SET MENU” parameters.

0 TRANSMIT indicator

Flashes while the remote control is sending infrared

signals.

Remote control

Note

TV MUTE TV INPUT

MUTE

AMP

SOURCE

TV

MENUTITLE

SET MENU

LEVEL

DISPLAYRETURN

BAND

SRCH MODE

DAB MEMORY

A/B/C/D/E

ENTER

PRESET/CH

REC

AUDIO

DISC SKIP

STEREO

1

EFFECT

VOLUME

TV VOL TV CH

TRANSMITCODE SET

STANDBY

POWER

POWERPOWER

CD

AVTV

MULTI CH IN

SLEEP

CD-R

DVD DTV

MD

CBL

TUNER

V-AUX DVR

STANDARD

5

SPEAKERS

9

MUSIC

2

SELECT

6

ENHANCER

0

ENTERTAIN

3

EXTD SUR.

7

NIGHT

10

MOVIE

4

DIRECT ST.

8

STRAIGHT

ENT.

FREQ/TEXT EONSTARTPTY SEEKMODE

K

0

A

B

C

D

F

E

G

H

I

J

1

2

3

4

5

6

8

9

7

L

Note

A on B on

A and B off

CONTROLS AND FUNCTIONS

7

INTRODUCTION

English

A STANDBY

Sets this unit to the standby mode (see page 28).

This button is operational only when MASTER ON/OFF on the

front panel is pressed inward to the ON position.

B POWER

Turns on this unit (see page 28).

This button is operational only when MASTER ON/OFF on the

front panel is pressed inward to the ON position.

C SLEEP

Sets the sleep timer (see page 35).

D MULTI CH IN

Selects the component connected to the MULTI CH

INPUT jacks as the input source when using an external

decoder, etc. (see page 38).

E VOLUME +/–

Increases or decreases the volume level.

F Component selector switch

Selects the operation mode of the remote control buttons

in the shaded areas.

AMP

Operates this unit.

SOURCE

Operates the component selected with an input

selector button (see page 85).

TV

Operates the TV assigned to either DTV/CBL or

(see page 84).

• To set the remote control codes for other components, see

page 86.

• When you set the remote control codes for both DTV/CBL and

(see page 86), priority is given to the one set for DTV/

CBL.

G MUTE

Mutes the audio output. Press again to restore the audio

output to the previous volume level (see page 34).

H STRAIGHT (EFFECT)

Turns the sound field programs off or on. When the

“STRAIGHT” mode is selected, 2-channel or multi-

channel input signals are output directly from their

respective speakers without effect processing

(see page 39).

I NIGHT

Turns on or off the night listening modes (see page 34).

J SET MENU

Enters “SET MENU” (see page 71).

K DISPLAY

Selects the on-screen display (OSD) mode for your video

monitor (see page 41).

L Radio Data System tuning buttons

(U.K. and Europe models only)

FREQ/TEXT

Switches the Radio Data System display between the

PS mode, PTY mode, RT mode, CT mode (if the

station offers the corresponding data services) and the

frequency display (see page 55).

PTY SEEK MODE

Sets this unit to the PTY SEEK mode (see page 53).

PTY SEEK START

Starts searching for a station once the desired program

type is selected in the PTY SEEK mode (see page 53).

EON

Selects a program type (NEWS, AFFAIRS, INFO, or

SPORT) for automatic tuning (see page 54).

Note

Notes

CONTROLS AND FUNCTIONS

8

■ Controlling the TUNER functions

Set the component selector switch to SOURCE and then

press TUNER to select “TUNER” as the input source.

4 Numeric buttons

Use numbers 1 through 8 to select preset stations.

7 BAND

Switches the reception band between FM and AM

(see page 46).

8 Cursor buttons u / d / j / i

Press j / i to select a preset station group (A to E) and

u / d to select a preset station number (1 to 8)

(see page 50).

■ Using the remote control

The remote control transmits a directional infrared ray.

Be sure to aim the remote control directly at the remote

control sensor on this unit during operation.

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following types

of conditions:

– places of high humidity, such as near a bath

– places of high temperatures, such as near a heater or stove

– places of extremely low temperatures

– dusty places

Notes

ZONE 2

ON/OFF

ZONE

CONTROL

VIDEO PORTABLEL AUDIO R

NEXTEDIT

EFFECT

MEMORY

FM/AM

PRESET/TUNING

A/B/C/D/E

PROGRAM

l PRESET/TUNING h

TUNING MODE

INPUT MODETONE CONTROLSTRAIGHT

SPEAKERSPHONES

MAIN ZONE

MASTER

SILENT CINEMA

BA

MULTI CH

INPUT

VOLUME

VIDEO AUX

INPUT

ON OFF

LEVEL

MAN'L/AUTO FM

AUTO/MAN'L

ON/OFF

30 30

TV MUTE TV INPUT

MUTE

AMP

SOURCE

TV

MENUTITLE

SET MENU

LEVEL

DISPLAYRETURN

BAND

SRCH MODE

DAB MEMORY

A/B/C/D/E

ENTER

PRESET/CH

REC

AUDIO

DISC SKIP

STEREO

1

EFFECT

VOLUME

TV VOL TV CH

TRANSMITCODE SET

STANDBY

POWER

POWERPOWER

CD

AVTV

MULTI CH IN

SLEEP

CD-R

DVD DTV

MD

CBL

TUNER

V-AUX DVR

STANDARD

5

SPEAKERS

9

MUSIC

2

SELECT

6

ENHANCER

0

ENTERTAIN

3

EXTD SUR.

7

NIGHT

10

MOVIE

4

DIRECT ST.

8

STRAIGHT

ENT.

FREQ/TEXT EONSTARTPTY SEEKMODE

Approximately 6 m

CONTROLS AND FUNCTIONS

9

INTRODUCTION

English

1 Decoder indicators

The respective indicator lights up when any of the

decoders of this unit function.

2 ENHANCER indicator

Lights up when the Compressed Music Enhancer mode is

turned on (see page 37).

3 Sound field indicators

Light up to indicate the active DSP sound fields.

4 VIRTUAL indicator

Lights up when Virtual CINEMA DSP is active (see

page 44).

5 Input source indicators

The corresponding cursor lights up to show the currently

selected input source.

6 DOCK indicator

Lights up when you station your iPod in a YAMAHA iPod

universal dock (such as YDS-10 sold separately)

connected to the DOCK terminal of this unit

(see page 22).

7 SILENT CINEMA indicator

Lights up when headphones are connected and a sound

field program is selected (see page 34).

8 CINEMA DSP indicator

Lights up when you select a CINEMA DSP sound field

program (see page 58).

9 AUTO indicator

Lights up when this unit is in the automatic tuning mode

(see page 46).

0 TUNED indicator

Lights up when this unit is tuned into a station

(see page 46).

A STEREO indicator

Lights up when this unit is receiving a strong signal for an

FM stereo broadcast while the AUTO indicator is lit

(see page 46).

B MEMORY indicator

Flashes to show that a station can be stored (see page 48).

C VOLUME level indicator

Indicates the current volume level.

D PCM indicator

Lights up when this unit is reproducing PCM (Pulse Code

Modulation) digital audio signals.

E STANDARD indicator

Lights up when the “SUR. STANDARD” or “SUR.

ENHANCED” program is selected (see page 43).

Front panel display

p

DVR

p

DVD

p

CD

p

V-AUX

p

DTV/CBL

p

MD/CD-R

p

TUNER

96

24

q PL

q EX

q PL

ENHANCER

MATRIX DISCRETE

SILENT CINEMA

ZONE2 NIGHT

DOCK

STANDARD

AUTO

PSHOLD RT

EON

PTYPTY

TUNED

MUTE

VOLUME

MEMORY

SLEEP

VIRTUAL

PCM

q PL x

A B

SP

mS

ft

dB

96/24

HiFi DSP

LFE

LCR

SL SB SR

q

DIGITAL

t

dB

STEREO

CT

2

H

EI

GJK LNMPO

Q

D

F

1345768 B

0A9C

(U.K. and Europe models only)

Presence DSP sound field

Listening position

Surround left

DSP sound field

Surround right

DSP sound field

Surround back DSP sound field

CONTROLS AND FUNCTIONS

10

F SP A B indicators

Light up according to the set of front speakers selected.

G Headphones indicator

Lights up when headphones are connected (see page 34).

H ZONE2 indicator

Lights up when Zone 2 is turned on (see page 90).

I NIGHT indicator

Lights up when you select a night listening mode

(see page 34).

J HiFi DSP indicator

Lights up when you select a HiFi DSP sound field

program (see page 58).

K Multi-information display

Shows the name of the current sound field program and

other information when adjusting or changing settings.

L SLEEP indicator

Lights up while the sleep timer is on (see page 35).

M MUTE indicator

Flashes while the MUTE function is on (see page 34).

N 96/24 indicator

Lights up when a DTS 96/24 signal is input to this unit.

O Input channel indicators

Indicate the channel components of the current digital

input signal (see page 30).

P LFE indicator

Lights up when the input signal contains the LFE signal.

Q Radio Data System indicators

(U.K. and Europe models only)

Lights up when the Radio Data System data is being

received.

EON

Lights up when the EON data service is being

received.

PTY HOLD

Lights up while searching for the Radio Data System

stations in the PTY SEEK mode.

CONTROLS AND FUNCTIONS

11

INTRODUCTION

English

1 Video component jacks

See pages 18 and 19 for connection information.

2 Audio component jacks

See page 21 for connection information.

3 MULTI CH INPUT jacks

See page 23 for connection information.

4 ZONE 2 OUTPUT jacks

See page 89 for connection information.

These jacks output analog signals only.

5 SUBWOOFER OUTPUT jack

See page 13 for connection information.

6 DIGITAL OUTPUT jack

See page 21 for connection information.

7 DIGITAL INPUT jacks

See page 19 for connection information.

8 DOCK terminal

Use to connect a YAMAHA iPod universal dock (such as

YDS-10 sold separately) where your iPod can be

stationed.

See page 22 for connection information.

9 COMPONENT VIDEO jacks

See pages 18 and 19 for connection information.

0 REMOTE jacks

See page 89 for details.

A CONTROL OUT jack

This is a control expansion terminal for custom

installation.

B Antenna terminals

See page 24 for connection information.

C Speaker terminals

See page 13 for connection information.

D AC OUTLET(S)

Use to supply power to your other audiovisual

components.

See page 26 for details.

■ VOLTAGE SELECTOR

(Asia and General models only)

See page 26 for details.

Rear panel

AUDIO AUDIO OUTPUT DIGITAL INPUT

DVD DVD

COAXIAL

DTV/CBLMD/CD-RMD/CD-R

SUB

WOOFER

SUB

WOOFER

SURROUND

FRONT ZONE 2

OUT

(REC)

IN

(PLAY)

MD/

CD-R

CD

DVD

MONITOR OUT

DTV/CBL

DVD DVR

COMPONENT VIDEO

P

RPBY

FM ANT

75Ω

UNBAL.

AM

ANT

GND

TUNER SPEAKERS

DOCK

DTV/CBL

IN OUT

DVR DVD DTV/CBL

IN OUT

DVR

CENTER

DIGITAL

OUTPUT

MULTI CH INPUT

VIDEO S VIDEO

MONITOR

OUT

MONITOR

OUT

FRONT

A

B

OUTIN

REMOTE CONTROL

OUT

+12V

15mA MAX.

SURROUND

CENTER

SURROUND BACK

PRPBY

OPTICAL OPTICAL

0

87654321

AB C

D

9

Note

CONNECTIONS

12

The speaker layout below shows the standard ITU-R

*

speaker setting. You can use it to enjoy CINEMA DSP and

multi-channel audio sources.

*

ITU-R is the radio communication sector of the ITU

(International Telecommunication Union).

Front left and right speakers (FL and FR)

The front speakers are used for the main source sound plus

effect sounds. Place these speakers at an equal distance

from the ideal listening position. The distance of each

speaker from each side of the video monitor should be the

same.

Center speaker (C)

The center speaker is for the center channel sounds

(dialog, vocals, etc.). If for some reason it is not practical

to use a center speaker, you can do without it. Best results,

however, are obtained with the full system. Place the

center speaker centrally between the front speakers and as

close to the monitor as possible, such as directly over or

under it.

Surround left and right speakers (SL and SR)

The surround speakers are used for effect and surround

sounds. Place these speakers behind your listening

position, facing slightly inwards, about 1.8 m above the

floor.

Surround back speaker (SB)

The surround back speaker supplements the surround

speakers and provides more realistic front-to-back

transitions. Place this speaker directly behind the listening

position and at the same height as the surround speakers.

Subwoofer (SW)

The use of a subwoofer with a built-in amplifier, such as

the YAMAHA Active Servo Processing Subwoofer

System, is effective not only for reinforcing bass

frequencies from any or all channels, but also for hi-fi

stereo sound reproduction of the LFE (low-frequency

effect) channel included in Dolby Digital and DTS

sources. The position of the subwoofer is not so critical,

because low bass sounds are not highly directional. But it

is better to place the subwoofer near the front speakers.

Turn it slightly toward the center of the room to reduce

wall reflections.

CONNECTIONS

Placing speakers

SW

FR

FL

SB

SL

SR

C

60˚

30˚

SB

FL

FR

C

SL

SR

80˚

SL

1.8 m

13

CONNECTIONS

PREPARATION

English

Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are faulty,

no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be

unnatural and lack bass.

• Before connecting the speakers, make sure that this unit is turned off (see page 28).

• Do not let the bare speaker wires touch each other or do not let them touch any metal part of this

unit. This could damage this unit and/or speakers.

• Use magnetically shielded speakers. If this type of speakers still creates the interference with the

monitor, place the speakers away from the monitor.

• If you are to use 4 or 6 ohm speakers, be sure to set “SP IMP.” to “6ΩMIN” before using this unit

(see page 27).

• A speaker cord is actually a pair of insulated cables running side by side. Cables are colored or shaped differently, perhaps with a

stripe, groove or ridge. Connect the striped (grooved, etc.) cable to the “+” (red) terminals of this unit and your speaker. Connect the

plain cable to the “–” (black) terminals.

• The low-frequency signals of other speakers set to “SML” (or “SMALL”) or to “NONE” in “SPEAKER SET” (see pages 72 and 73)

are directed to the speakers selected in “LFE/BASS OUT” (see page 73).

Connecting speakers

Notes

CAUTION

OUTPUT

SUB

WOOFER

SPEAKERS

FRONT

A

B

SURROUND

CENTER SURROUND BACK

1 2 4 57

63

Subwoofer

Center

speaker

Front speakers (A)

Surround back

speaker

LeftRight

Surround speakers

Front

speakers

(B)

14

CONNECTIONS

FRONT terminals

Connect one or two front speaker systems (1, 2) to these

terminals. If you use only one front speaker system,

connect it to the FRONT A or B terminal.

CENTER terminals

Connect a center speaker (3) to these terminals.

SURROUND terminals

Connect surround speakers (4, 5) to these terminals.

SURROUND BACK terminals

Connect a surround back speaker (6) to these terminals.

SUBWOOFER jack

Connect a subwoofer with a built-in amplifier (7) (such as

the YAMAHA Active Servo Processing Subwoofer

System) to this jack.

7

1

2

6

5

4

3

Speaker layout

15

CONNECTIONS

PREPARATION

English

■ Connecting the speaker cable

1 Remove approximately 10 mm of insulation

from the end of each speaker cable and then

twist the exposed wires of the cable together

to prevent short circuits.

2 Loosen the knob.

3 Insert one bare wire into the hole on the side

of each terminal.

4 Tighten the knob to secure the wire.

■ Connecting the banana plug

(except U.K., Europe and Asia models)

The banana plug is a single-pole electrical connector

widely used to terminate speaker cables.

1 Tighten the knob.

2 Insert the banana plug connector into the

end of the corresponding terminal.

10 mm

Red: positive (+)

Black: negative (–)

Red: positive (+)

Black: negative (–)

Red: positive (+)

Black: negative (–)

Banana plug

16

CONNECTIONS

You can use the digital jacks to input PCM, Dolby Digital and DTS bitstreams. When you connect components to both the COAXIAL

and OPTICAL jacks, priority is given to the signals input at the COAXIAL jack. All digital input jacks are compatible with 96-kHz

sampling digital signals.

■ Audio jacks

This unit has four types of audio jacks. Connection

depends on the availability of audio jacks on your other

components.

AUDIO jacks

For conventional analog audio signals transmitted via left

and right analog audio cables. Connect red plugs to the

right jacks and white plugs to the left jacks.

DIGITAL AUDIO COAXIAL jacks

For digital audio signals transmitted via coaxial digital

audio cables.

DIGITAL AUDIO OPTICAL jacks

For digital audio signals transmitted via optical digital

audio cables.

Pull out the cap from the optical jack before you connect the fiber

optic cable. Do not discard the cap. When you are not using the

optical jack, be sure to put the cap back in place. This cap protects

the jack from dust.

PORTABLE jack

For analog audio signals transmitted via stereo analog

audio mini cables.

■ Video jacks

This unit has three types of video jacks. Connection

depends on the availability of input jacks on your video

monitor. When “VIDEO CONV.” is set to “ON” (see

page 79), the video signals input at the VIDEO and S

VIDEO jacks are converted and output at the VIDEO, S

VIDEO and COMPONENT VIDEO jacks

interchangeably.

VIDEO jacks

For conventional composite video signals transmitted via

composite video cables.

S VIDEO jacks

For S-video signals, separated into the luminance (Y) and

chrominance (C) video signals transmitted on separate

wires of S-video cables.

COMPONENT VIDEO jacks

For component video signals, separated into the

luminance (Y) and chrominance (P

B, PR) video signals

transmitted on separate wires of component video cables.

Information on jacks and cable plugs

Note

VIDEO S VIDEO

COMPONENT VIDEO

Y PB PR

PB

Y

P

R

S

V

COAXIAL

DIGITAL AUDIO

AUDIO

PORTABLE

OPTICAL

DIGITAL AUDIO

R

L

C

O

M

R

L

Left and right

analog audio

cable plugs

Optical

digital

audio cable

plug

Coaxial

digital audio

cable plug

Composite

video cable

plug

S-video

cable plug

Component

video cable

plugs

Stereo

analog

audio

mini cable

plug

Audio jacks and cable plugs Video jacks and cable plugs

(Red)(White) (Orange) (Yellow) (Green) (Blue) (Red)

Note

17

CONNECTIONS

PREPARATION

English

■ Audio signal flow for AUDIO OUT (REC)

This unit handles digital and analog signals independently. Thus, audio signals input at the analog jacks are output only at the analog

AUDIO OUT (REC) jacks. Likewise, audio signals input at the DIGITAL INPUT (OPTICAL or COAXIAL) jacks are output only at the

DIGITAL OUTPUT jack.

■ Video signal flow for MONITOR OUT

When video signals are input at the COMPONENT VIDEO, S VIDEO and VIDEO jacks, the priority order of the input signals is as

follows where the video signals input at the COMPONENT VIDEO jacks have the top priority:

COMPONENT VIDEO > S VIDEO > VIDEO

Audio and video signal flow

Note

DIGITAL AUDIO

OPTICAL

DIGITAL AUDIO

COAXIAL

PORTABLE

AUDIO

RLRL

Digital output

Output

AUDIO OUT (REC)

Input

Analog output

Digital audio

Analog audio

S VIDEO

VIDEO

COMPONENT

VIDEO

Y P

B

P

R

Y P

B

P

R

Through

Output

(MONITOR OUT)

Input

Video conversion when “VIDEO CONV.” is set to “ON” (see page 79)

Analog video

18

CONNECTIONS

Connect your TV to the VIDEO MONITOR OUT jack, the S VIDEO MONITOR OUT jack or the COMPONENT

VIDEO MONITOR OUT jacks of this unit.

Do not connect this unit or other components to the AC power supply until all connections between

components are complete.

Connecting a TV

CAUTION

MONITOR OUT

COMPONENT VIDEO

VIDEO S VIDEO

MONITOR

OUT

MONITOR

OUT

PRPBY

PRPB

V

S

Y

TV

S-video in

Component video in

Video in

La pagina sta caricando ...

Yamaha RX-V559 Manuale del proprietario

Questo manuale è adatto anche per

Yamaha RX-V559 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti