ESAB Mig L3000i Origo™ Mig L3000i Manuale utente

Categoria
Sistema di saldatura
Tipo
Manuale utente
Valid for serial no. 802--xxx--xxxx0459 827 227 080328
Mig L3000i
Aristot /Origot
Instruction manual Èíñòðóêöèÿ ïî ýêñïëóàòàöèè
-- 2 --
Rights reserved to alter specifications without notice.
Îñòàâëÿåì çà ñîáîé ïðàâî èçìåíÿòü ñïåöèôèêàöèþ áåç ïðåäóïðåæäåíèÿ.
Ðóññêèé 3...............................................
ENGLISH 12..............................................
Ðóññêèé
TOCr
-- 3 --
1 ÒÅÕÍÈÊÀ ÁÅÇÎÏÀÑÍÎÑÒÈ 4........................................
2 ÂÂÅÄÅÍÈÅ 6.......................................................
2.1 Îáîðóäîâàíèå 6...........................................................
3 ÒÅÕÍÈ×ÅÑÊÈÅ ÕÀÐÀÊÒÅÐÈÑÒÈÊÈ 6................................
ÑÒÀÍÎÂÊÀ 7.......................................................
4.1 Ðàñïîëîæåíèå 7...........................................................
4.2 Ñåòü ýëåêòðîïèòàíèÿ 8.....................................................
5 ÏÎÐßÄÎÊ ÐÀÁÎÒÛ 9...............................................
5.1 Ñîåäèíåíèÿ è óñòðîéñòâà óïðàâëåíèÿ 9.....................................
5.2 Óïðàâëåíèå âåíòèëÿòîðàìè 9...............................................
5.3 Çàùèòà îò ïåðåãðåâà 9.....................................................
6 ÒÅÕÍÈ×ÅÑÊÎÅ ÎÁÑËÓÆÈÂÀÍÈÅ 10.................................
6.1 Ïðîâåðêà è î÷èñòêà 10......................................................
7 ÂÛßÂËÅÍÈÅ ÍÅÈÑÏÐÀÂÍÎÑÒÅÉ 10.................................
8 ÇÀÊÀÇ ÇÀÏÀÑÍÛÕ ×ÀÑÒÅÉ 11.......................................
ÑÕÅÌÀ 20..............................................................
ÍÎÌÅÐ ÇÀÊÀÇÀ 22.....................................................
ÄÎÏÎËÍÈÒÅËÜÍÛÅ ÏÐÈÍÀÄËÅÆÍÎÑÒÈ 23...........................
ba40d1ra -- 4 --
1 ÒÅÕÍÈÊÀ ÁÅÇÎÏÀÑÍÎÑÒÈ
Ïîëüçîâàòåëè ñâàðî÷íîãî îáîðóäîâàíèÿ ESAB îòâå÷àþò çà âûïîëíåíèå ïðàâèë òåõíèê è
áåçîïàñíîñòè ëèöàìè, ðàáîòàþùèìè íà îáîðóäîâàíèè è ðÿäîì ñ íèì. Ïðàâèëà òåõíèêè
áåçîïàñíîñòè äîëæíû îòâå÷àòü òðåáîâàíèÿì ê áåçîïàñíîé ýêñïëóàòàöèè ñâàðî÷íîãî
îáîðóäîâàíèÿ ýòîãî òèïà. Ïîìèìî ñòàíäàðòíûõ ïðàâèë òåõíèêè áåçîïàñíîñòè è îõðàíû
òðóäà íà ðàá î÷åì ìåñòå ðåêîìåíäóåòñÿ ñëåäóþùåå.
Âñå ðàáîòû äîëæíû âûïîëíÿòüñÿ ïîäãîòîâëåííûìè ëèöàìè, çíàêîìûìè ñ ýêñïëóàòàöèåé
ñâàðî÷íîãî îáîðóäîâàíèÿ. Íåïðàâèëüíàÿ ýêñïëóàòàöèÿ îáîðóäîâàíèÿ ìîæåò âûçâàòü
îïàñíûì ñèòóàöèè, ïðèâîäÿùèå ê òðàâìèðîâàíèþ ïåðñîíàëà è ïîâðåæäåíèþ
îáîðóäîâàíèÿ.
1. Bñå ëèöà, èñïîëüçóþùèå ñâàðî÷íîå îáîðóäîâàíèå, äîëæíû çíàòü:
S èíñòðóêöèè ïî ýêñïëóàòàöèè
S ðàñïîëîæåíèå îðãàíîâ àâàðèéíîãî îñòàíîâà
S íàçíà÷åíèå îáîðóäîâàíèÿ
S ïðàâèëà òåõíèêè áåçîïàñíîñòè
S òåõíîëîãèþ ñâàðêè
2. Îïåðàòîð îáåñïå÷èâàåò:
S óäà ëåíèå ïîñòîðîííèõ ëèö èç ðàá î÷åé çîíû îáîðóäîâàíèÿ ïðè åãî çàïóñêå
S çàùèòó âñåõ ëèö îò â îçäåéñòâèÿ ñâàðî÷íîé äóãè
3. Ðàáî÷åå ìåñòî äîëæíî:
S îòâå÷àòü óñëîâèÿì ýêñïëóàòàöèè
S íå èìåòü ñêâîçíÿêîâ
4. Ñðåäñòâà çàùèòû ïåðñîíàëà
S Âî âñåõ ñëó÷àÿõ ðåêîìåíäóåòñÿ èñïîëüçîâàòü èíäèâèäóàëüíûå ñðåäñòâà çàùèòû,
íàïðèìåð, çàùèòíûå î÷êè, îãíåñòîéêóþ ñïåöîäåæäó è çàùèòíûå ðóêàâèöû.
S Ïðè ñâàðêå çàïðåùàåòñÿ íîñèòü ñâîáîäíóþ îäåæäó, óêðàøåíèÿ è ò.ä., íàïðèìåð,
øàðôû, áðàñëåòû, êîëüöà, êîòîðûå ìîãóò ïîïàñòü â ñâàðî÷íîå îáîðóäîâàíèå èëè
âûçâàò ü îæîãè.
5. Îáùèå ìåðû ïðåäîñòîðîæíîñòè
S Ïðîâåðüòå íàäåæíîñòü ïîäêëþ÷åíèÿ îáðàòíîãî êàáåëÿ.
S Ðàáîòû íà îáîðóäîâàíèè ñ âûñîêèì íàïðÿæåíèåì äîëæíû ïðîèçâîäèòüñÿ
òîëüêî êâàëèôèöèðîâàííûì ýëåêòðèêîì.
S Â ïðåäåëàõ äîñòóïà äîëæíû íàõîäèòüñÿ ñîîòâåòñòâóþùèå ñðåäñòâà
ïîæàðîòóøåíèÿ, èìåþùèå ÿñíóþ ìàðêèðîâêó.
S Çàïðåù àåòñÿ ïðîâîäèòü ñìàçêó è òåõíè÷åñêîå îáñëóæèâàíèå îáîðóäîâàíèå âî
âðåìÿ ýêñïëóàòàöèè.
RU
ba40d1ra -- 5 --
Ïåðåä íà÷àëîì ìîíòàæà è ýêñïëóàòàöèè âíèìàòåëüíî èçó÷èòå ñîîòâåòñòâóþùèå èíñòðóêöèè.
ÇÀÙÈÒÈÒÅ ÑÅÁß È ÄÐÓÃÈÕ!
ÂÍÈÌÀÍÈÅ!
Äóãoaaÿ caapka è peçka oïacíû kak äëa ècïoëíèteëÿ paáît, tak è äëa ïîctopoííèõëèö. Tpeáyéte
coáëþäåíèå àñå õ ïðààèë áåçîïàñíîñòè, äåéñòàóþùèõ íà îáúåêòå, êîòîðûå äîëæíû ó÷èòûààòú
ñåäåíèÿ îá îïàñíîñòÿõ, ïðåäñòààëåííûå èçãîãàèòåëåì ñààð î÷íîãî îáîðóäîààíèà.
ÎÏÀÑÍÎÑÒÜ ÑÌÅÐÒÅËÜÍÎÃÎ ÏÎÐÀÆÅÍÈß ÝËÅÊÒÐÈ×ÅÑÊÈÌ ÒÎÊÎÌ.
S Ñâàðî÷íûé àãðåãàò óñòàíàâëèâàåòñÿ è çàçåìëÿåòñÿ â ñîîòâåòñòâèè ñ äåéñòâóþùèìè íîðìàìè è
ïðàâèëàìè.
S Íå äîïóñêàéòå êîíòàêòà íàõîäÿùèõñÿ ïîä íàïðÿæåíèåì äåòàëåé è ýëåêòðîäîâ ñ íåçàùèùåííûìè
÷àñòÿìèòåëàîêðûìèðóêàâèöàìèèìîêðîéîäåæäîé.
S Îáåñïå÷üòå ýëåêòðè÷åñêóþ èçîëÿöèþ î ò çåìëè è ñâàðèâàåìûõ äåòàëåé.
S Îáåñïå÷üòå ñîáëþäåíèå áåçîïàñíûõ ðàáî÷èõ ðàññòîÿíèé.
ÄÛÌÛ È ÃÀÇÛ ìîãóò áûòü îïàñíû äëÿ ÷åëîâåêà
S Èñêëþ÷èòå âîçìî æíîñòü âîçäåéñòâèÿ äûìîâ.
S Äëÿ èñêëþ÷åíèÿ âäûõàíèÿ äûìîâ âî âðåìÿ ñâàðêè îðãàíèçóåòñÿ îáùàÿ âåíòèëÿöèÿ ïîìåùåíèÿ, à
òàêæåâûòÿæíàÿâåíòèëÿöèÿèççîíûñâàðêè.
ÈÇËÓ×ÅÍÈÅ ÄÓÃÈ âûçûâàåò ïîðàæåíèå ãëàç è îæîãè êîæè.
S Çàùèòèòå ãëàçà è êîæó. Äëÿ ýò îãî èñïîëüçóéòå çàùèòíûå ùèòêè, öâåòíûå ëèíçû è çàùèòíóþ
ñïåöîäåæäó.
S Äëÿ çàùèòû ïîñòîðîííèõ ëèö ïðèìåíÿþòñÿ çàùèòíûå ýêðàíû èëè çàíàâåñè.
ÏÎÆÀÐÎÎÏÀÑÍÎÑÒÜ
S Èñêðû (áðûçãè ìåòàëëà) ìîãóò âûçâàòü ïîæàð. Óáåäèòåñü â îòñóòñòâèè ãîðþ÷èõ ìàòåðèàëîâ
ïîáëèçîñòè îò ìåñòà ñâàðêè.
ØÓÌ - ×ðåçìåðíûé øóì ìîæåò ïðèâåñòè ê ïîâðåæäåíèþ îðãàíîâ ñëóõà
S Ïðèìèòå ìåðû äëÿ çàùèòû ñëóõà. Èñïîëüçóéòå çàòû÷êè äëÿ óøåé èëè äðóãèå ñðåäñòâà çàùèòû
ñëóõà.
S Ïðåäóïðåäèòå ïîñòîðîííèõ ëèö îá îïàñíîñòè.
ÍÅÈÑÏÐÀÂÍÎÑÒÈ -- Ïðè íåèñïðàâíîñòè îáðàòèòåñ ü ê ñïåöèàëèñòàì ïî ñâàðî÷íîìó
îáîðóäîâàíèþ
Êîìïàíèÿ ESAB ãîòîâà ïðåäîñòàâèòü âàì âñå çàùèòíîå ñíàðÿæåíèå è
ïðèíàäëåæíîñòè, íå îáõîäèìûå äëÿ âûïîëíåíèÿ ñâàðî÷íûõ ð àáîò.
ÂÍÈÌÀÍÈÅ!
Çàïðåùàåòñÿ èñïîëüçîâàòü èñòî÷íèê ïèòàíèÿ äëÿ îòòàèâàíèÿ òðóá.
ÎÑÒÎÐÎÆÍÎ!
Îáîðóäîâàíèå Class À íå ïðåäíàçíà÷å íî äëÿ èñïîëüçîâàíèÿ â
æèëûõ ïîìåùåíèÿõ, ãäå ýëåêòðîñíàáæåíèå îñóùåñòâëÿåòñÿ èç
áûòîâûõ ñåòåé íèçêîãî íàïðÿæåíèÿ. Â òàêèõ ìåñòàõ ìîãóò
ïîÿâèòüñÿ ïîòåíöèàëüíûå òðó äíîñòè îáåñïå÷åíèå
ýëåêòðîìàãíèòíîé ñîâìåñòèìîñòè îáîðóäîâàíèÿ Class À
âñëåäñòâèå êîíäóêòèâíûõ è ðàäèàöèîííûõ ïîìåõ.
Äàííîå èçäåëèå ïðåäíàçíà÷åíî òîëüêî äëÿ äóãîâîé ñâàðêè.
RU
ba40d1ra -- 6 --
ÎÑÒÎÐÎÆÍÎ!
Ïåðåä íà÷àëîì ìîíòàæà è ýêñïëóàòàöèè
âíèìàòåëüíî è çó÷èòå ñîîòâåòñòâóþùèå
èíñòðóêöèè.
2 ÂÂÅÄÅÍÈÅ
Áëîê Mig L3000i ïðåäñòàâëÿåò ñîáîé èñòî÷íèê ïèòàíèÿ äëÿ ýëåêòðîäóãîâîé
ñâàðêè â ñðåäå çàùèòíîãî ãàçà îáû÷íîé ñâàðî÷íîé ïðîâîëîêîé (MIG), ëèáî
áåç ãàçà ñ èñïîëüçîâàíèåì ïðîâîëîêè ñ ôëþñîì (MAG), íî ìîæåò áûòü òàêæå
èñïîëüçîâàí äëÿ ñâàðêè ïîêðûòûì ýëåêòðîäîì (MMA). Èñòî÷íèê ïèòàíèÿ
èñïîëüçóåòñÿ â ñî÷åòàíèè ñ áëîê îì ïîäà÷è ïðîâîëîêè Feed L3004.
Íàñòðîéêà âñåõ óñòà âîê îñóùåñòâëÿåòñÿ íà áëîêå ïîäà÷è ïðîâîëîêè.
Àêñåññóàð² îò ä ëÿ èçäåëÿ ìîæíî íàéòè íà ñòðíèöå 23.
2.1 Îáîðóäîâàíèå
Èñòî÷íèê ïèòàíèÿ êîìïëåêò óåòñÿ îáðàòíûì êàáåëåì äëèíîé 5 ì è
ðóêîâîäñòâîì ïî ýêñïëóàòàöèè.
3 ÒÅÕÍÈ×ÅÑÊÈÅ ÕÀÐÀÊÒÅÐÈÑÒÈÊÈ
Mig L3000i
Íàïðÿæåíèå ñåòè
400 Â, ±10%, 3 50/60 Ãö
Ïèòàíèå îò ñåòè S
sc min
1,4 MVA
Ïåðâè÷íûé òîê
I
ìàêñ.
(MIG/MAG)
I
max
(MMA)
16 A
19 A
Ïîòðåáëÿåìàÿ ìîùíîñòü õîëîñòîãî õîäà â
ðåæèìå ýíåðãîñáåðåæåíèÿ, 6,5 ìèí ïîñëå
ñâàðêè
30 Âò
Äèàïàçîí óñòàâîê
Ñâàðêà MIG/MAG
MMA
8-48 Â / 16-300 À
16-300 À
Äîïóñòèìàÿ íàãðóçêà ïðè (MIG/MAG)
ðàáî÷åì öèêëå 35%
ðàáî÷åì öèêëå 60%
ðàáî÷åì öèêëå 100%
300 À / 29 Â
24/2
200 À / 24 Â
Äîïóñòèìàÿ íàãðóçêà ïðè MMA
ðàáî÷åì öèêëå 30%
ðàáî÷åì öèêëå 60%
ðàáî÷åì öèêëå 100%
300 À / 32 Â
230 À / 29,2 Â
19/27,
Êîýôôèöèåíò ìîùíîñòè ïðè
ìàêñèìàëüíîì òîêå
MIG/MAG
MMA
0.90
0.90
Êïä ïðè ìàêñèìàëüíîì òîêå
MIG/MAG
MMA
85 %
84 %
RU
ba40d1ra -- 7 --
Mig L3000i
Íàïðÿæåíèå õîëîñòîãî õîäà
MIG/MAG
MMA
70 - 80 Â
57 -67 Â
Ðàáî÷àÿ òåìïåðàòóðà îò -10 äî +40˚C
Ïîñòîÿííûé ýêâèâàëåíòíûé óðîâåíü
çâóêîâîãî äàâëåíèÿ ïî øêàëå À
<7Á
Ðàçìåðû, ä x ø x â 652 x 2 49 x 423 ìì
Ìàññà 29 êã
Êëàññ èçîëÿöèè òðàíñôîðìàòîðà H
Ê ëàññ çàùèòû êîðïóñà IP23C
Êëàññ ïðèìåíåíèÿ
Ðàáî÷èé öèêë
Ðàáî÷èé öèêë ïðåäñòàâëÿåò ñîáîé äîëþ %%) äåñÿòèìèíóòíîãî èíòåðâàëà, â òå÷åíèå
êîòîðîé ìîæíî ïðîèçâîäèòü ñâàðêó ïðè îïðåäåëåííîé íàãðóçêå áåç ïåðåãðóçêè.
Êëàññ êîæóõà
Íîðìû IP óêàçûâàþò êëàññ êîæóõà, ò.å., ñòåïåíü çàùèòû îò ïðîíèêíîâåíèÿ òâåðäûõ
îáúåêòîâ è âîäû. Îáîðóäîâàíèå ñ ìàðêèðîâêîé IP 23 ïðåäíàçíà÷åíî äëÿ íàðóæíîé è
âíóòðåííåé óñòàíîâêè.
Ê ëàññ çîíû óñòàíîâêè
Ýòîò ñèìâîë îçíà÷àåò, ÷òî èñòî÷íèê ïèòàíèÿ ïðåäíàçíà÷åí äëÿ èñïîëüçîâàíèÿ â çîíàõ
ñ ïîâûøåííîé îïàñíîñòüþ ïîðàæåíèÿ ýëåêòðî òîê îì.
Ïèòàíèå îò ñåòè, S
sc ìèí.
Ìíèìà ëüíàÿ ìîùíîñòü ïðè êîðîòêîì çàìûêàíèè ñåòè â ñîîòâåòñòâèè ñî ñòàíäàðòîì IEC
61000-3-12
ÑÒÀÍÎÂÊÀ
Ââîä â ýêñïëóàòàöèþ äîëæåí ïðîèçâîäèòüñÿ êâàëèôèöèðîâàííûì
ñïåöèàëèñòîì.
Ïðèìe÷aíèå!
Òðåáîâàíèÿ ê ñåòÿì ýëåêòðîñíàáæåíèÿ
Èç-çà áîëüøèõ âåëè÷èí òîêà â ïåðâè÷íîé îáìîòêå îáîðóäîâàíèå âûñîêîé ìîùíîñòè
ìîæåò ñóùåñòâåííî ïîâëèÿòü íà ìîùíîñòíûå õàðàêòåðèñòèêè ñåòè. Ïîýòîìó â îòíîøåíèè
íåêîòîðîãî îáîðóäîâàíèÿ ïðèìåíÿþòñÿ îãðàíè÷åíèÿ èëè äîïîëíèòåëüíûå òðåá îâàíèÿ,
êàñàþùèåñÿ ìàêñèìàëüíî äîïóñòèìîãî ñîïðîòèâëåíèÿ îáîðóäîâàíèÿ èëè ì èíèìàëüíîé
ñïîñîáíîñòè îáåñïå÷èòü ñòàáèëüíîå ýíåðãîñíàáæåíèå â òî÷êàõ âçàèìîäåéñòâèÿ
îáùåñòâåííûõ ñåòåé.  òàêîì ñëó÷àå ïîëüçîâàòåëü îáîðóäîâàíèÿ èëè òîò, êòî åãî
óñòàíàâëèâàåò, äîëæåí ïðîêîíñóëüòèðîâàòüñÿ ñ îïåðàòîðîì ýíåðãîñåòè ïî ïîâîäó
âîçìî æíîñòè ïîäêëþ÷åíèÿ òàêîãî ðîäà îáîðóäîâàíèÿ.
4.1 Ðàñïîëîæåíèå
Ðàçìåñòèòå ñâàðî÷íûé èñòî÷íèê ïèòàíèÿ òàêèì îáðàçîì, ÷òîáû åãî
âîçäóõîçàáîðíûå è âûïóñêíûå îòâåðñòèÿ íå áûëè çàãðàæäåíû.
RU
ba40d1ra -- 8 --
4.2 Ñåòü ýëåêòðîïèòàíèÿ
Óáåäèò åñü â òîì, ÷ò î áëîê ïîäêëþ÷åí ê ñåòè
ýëåêòðîïèòàíèÿ ñ òðåáóåìûì íàïðÿæåíèåì è çàùèùåí
ïðåäîõðàíèòåëÿìè òðåáóåìîãî íîìèíàëà. Íåîáõîäèìî
îáåñïå÷èòü çàùèòíîå çàçåìëåíèå â ñîîòâåòñòâèè ñ
äåéñòâóþùèìè íîðìàìè.
Ïàñïîðòíàÿ òàáëè÷êà ñ ïàðàìåòðàìè ñåòè ýëåêòðîïèòàíèÿ.
Ðåêîìåíäóåìûå íîìèíàëû ïðåäîõðàíèòåëåé è ìèíèìàëüíàÿ ïëîùàäü
ïîïåðå÷íîãî ñå÷åíèÿ êàáåëåé
Mig L3000i MIG/MAG MMA
Íàïðÿæåíèå ñåòè 400 Â 3μ 50 Ãö 400 Â 3μ 50 Ãö
Ïëîùàäü ïîïåðå÷íîãî ñå÷åíèÿ
ñèëîâîãî êàáåëÿ ïèòàíèÿ, ìì
2
4G2.5 4G2.5
Ôàçíûé òîê, I
eff
I
ñðåäíåêâàäðàòè÷íîå
äåéñòâóþùåå çíà÷åíèå
10 A 10 A
Ïðåäîõðàíèòåëü
Óñòîé÷èâûé ê ïåðåíàïðÿæåíèÿì
Òèï C, ìèíèàòþðíûé
âûêëþ÷àòåëü
16 A
16 A
16 A
16 A
Âíèìàíèå! Ïðèâåäåííûå âûøå çíà÷åíèÿ ïëîùàäè ïîïåðå÷íîãî ñå÷åíèÿ ñèëîâûõ êàáåëåé è
íîìèíàëû ïðåäîõðàíèòåëåé ñîîòâåòñòâóþò øâåäñêèì íîðìàì. Ýêñïëóàòàöèÿ èñòî÷íèêà
ñâàðî÷íîãî òîêà äîëæíà îñóùåñòâëÿòüñÿ â ñîîòâåòñòâèè ñ äåéñòâóþùèìè íàöèîíàëüíûìè
íîðìàòèâíûìè äîêóìåíòàìè.
Âíèìàíèå! Ýòîò èñòî÷íèê ñâàðî÷íîãî òîêà ðàññ÷èòàí íà ïîäêëþ÷åíèå ê
÷åòûðåõïðîâîäíîé ñèñòåìå íàïðÿæåíèåì 230/400 Âîëüò.
Åñëè èñòî÷íèê ïèòàíèÿ ïðåäïîëàã àåòñÿ èñïîëüçîâàòü â ñòðàíå ñ áîëåå
âûñîêèì ñåòåâûì íàïðÿæåíèåì, èñòî÷íèêà ïèòàíèÿ íóæíî ïîäêëþ÷àòü ÷åð åç
çàùèòíûé òðàíñôîðìàòîð.
RU
ba40d1ra -- 9 --
5 ÏÎÐßÄÎÊ ÐÀÁÎÒÛ
Îáùèå ïðàâèëà òåõíèêè áåçîïàñíîñòè ïðè ðàáîòå ñ îáîðóäîâàíèåì
ïðèâîäÿòñÿ íà ñòð. 4. Ïðî÷òèòå èõ äî èñïîëüçîâàíèÿ îáîðóäîâàíèÿ!
5.1 Ñîåäèíåíèÿ è óñòðîéñòâà óïðàâëåíèÿ
1 Ñîåäèíèòåëü îõëàæäàþùåãî
óñòðîéñòâà, áëîêà ïîäà÷è ïðîâîëîêè
èëè áëîêà äèñòàíöèîííîãî óïðàâëåíèÿ
3 Ñîåäèíèòåëü ñâàðî÷íîãî êàáåëÿ (-)
Ñâàðêà ìåòîäîì ÌMA
2 Ñîåäèíèòåëü îáðàòíîãî êàá åëÿ (-) 4 Ïåðåêëþ÷àòåëü íàïðÿæåíèÿ ñåòè 1 / 0
5.2 Óïðàâëåíèå âåíòèëÿòîðàìè
Áëîê ïèòàíèÿ ñíàáæåí òàéìåðîì, êîòîðûé âûê ëþ÷àåò âåíòèëÿòîðû ÷åðåç 6,5
ìèíóò ïîñëå ïðåêðàùåíèÿ ñâàðêè, è ïåðåâîäèò óñòðîéñòâî â ðåæèì
ýíåðãîñáåðåæåíèÿ. Ïðè âîçîáíîâëåíèè ñâàðêè âåíòèëÿòîðû âíîâü íà÷íó ò
ðàáîòàòü.
Âåíòèëÿòîðû ðàáîòàþò íà ïîíèæåííûõ îáîðîòàõ ïðè ñâàðî÷íûõ òîêàõ äî 110 A
èíàïîëíûõîáîðîòàõïðèáîëüøèõòîêàõ.
5.3 Çàùèòà îò ïåðåãðåâà
Èñòî÷íèê ñâàðî÷íîãî òîêà ñíàáæåí çàùèòîé îò ïåðåãðåâà, êîòîðàÿ
ñðàáàòûâàåò, êîãäà òåìïåðàòóðà óñòðîéñòâà ñòàíîâèòñÿ ñëèøêîì âûñîêîé. Â
ýòîì ñëó÷àå ïðåêðàùàåòñÿ ïîäà÷à ñâàðî÷íîãî òîêà, à íà äèñïëåå ïàíåëè
óïðàâëåíèÿ áëîêà ïîäà÷è ïðîâîëîêè âûñâå÷èâàå òñÿ êîä îòêàçà.
Êîãäà òåìïåðàòóðà ñíèçèòñÿ, ðåëå âíîâü àâòîìàòè÷åñêè âêëþ÷àòñÿ.
RU
ba40d1ra -- 1 0 --
6 ÒÅÕÍÈ×ÅÑÊÎÅ ÎÁÑËÓÆÈÂÀÍÈÅ
Ðåã óëÿðíîå òåõíè÷åñêîå îáñëóæèâàíèå èìååò âàæíîå çíà÷åíèå ä ëÿ
áåçîïàñíîé è íàäåæíîé ðàáîòû îáîðóäîâàíèÿ.
Òîëüêî ëèöà, èìåþùèå êâàëèôèêàöèþ ýëåêòðèêà òòåñòîâàííûé ïåðñîíàë),
èìåþò ïðàâî ñíèìàòü ïàíåëè, îáåñïå÷èâàþùèå áåçîïàñíîñòü ð àáîòû.
Äàííîå èçäåëèå ïðåäíàçíà÷åíî òîëüêî äëÿ äóãîâîé ñâàðêè.
6.1 Ïðîâåðêà è î÷èñòêà
Ðåãóëÿðíî ï ðîâåðÿéòå, ÷òîáû áëîê ïîäà÷è ï ðîâîëîêè íå áûë çàáèò ãðÿçüþ.
Ïåðèîäè÷íîñòü ïðîâåðêè è ïðèìåíÿåìûå ìåòîäû î÷èñòêè çàâèñÿò îò:
òåõíîëîãèè ñâàðêè, äëèòåëüíîñòè ãîðåíèÿ äóãè è óñëîâèé îêðóæàþùåé ñðåäû.
Îáû÷íî äîñòàòî÷íî îñóùåñòâëÿòü ïðîäóâêó èñòî÷íèêà ïèòàíèÿ ñòðóåé ñæàòîãî
âîçäóõà îíèæåííîãî äàâëåíèÿ) îäèí ðàç â ãîä.
Çàñîðåííûå èëè çàêóïîðåííûå îòâåðñòèÿ äëÿ ïîäâîäà è îòâîäà âîçäóõà òàêæå
ìîãóò ñòàòü ïðè÷èíîé ïåðåãðåâà óñòðîéñòâà.
7 ÂÛßÂËÅÍÈÅ ÍÅÈÑÏÐÀÂÍÎÑÒÅÉ
Ïðåæäå ÷åì âûçûâàòü àòòåñòîâàííîãî ñïåöèàëèñòà ïî îáñëóæèâàíèþ,
ïîïðîáóéòå ñàìîñòîÿòåëüíî âûïîëíèòü ðåêîìåíäóåìûå íèæå ïðîâåðêè.
Òèï íåèñïðàâíîñòè Äåéñòâèÿ:
Îòñóòñòâèå äóãè S Ïðîâåðüòå, âêëþ÷åí ëè âûêëþ÷àòåëü ïèòàíèÿ.
S Ïðîâåðüòå ïðàâèëüíîñòü ïîäñîåäèíåíèÿ êàáåëåé
ïîäà÷è ñâàðî÷íîãî òîêà è îáðàòíûõ êàáåëåé.
S Ïðîâåðüòå, ïðàâèëüíî ëè çàäàíà âåëè÷èíà òîêà.
 ïðîöåññå ñâàðêè ïðîïàë
ñâàðî÷íûé òîê.
S Ïðîâåðüòå, íå ñðàáîòàëà ëè çàùèòà îò ïåðåãðåâà (íà
ïàíåëè óïðàâëåíèÿ âûñâå÷èâàåòñÿ êîä îòêàçà E6).
S Ïðîâåðüòå ñåòåâûå ïðåäîõðàíèòåëè.
×àñòî ñðàáàòûâàå ò çàùèòà îò
ïåðåãðåâà.
S Óáåäèòåñü â òîì, ÷òî íå ïðåâûøåíû íîìèíàëüíûå
çíà÷åíèÿ ïàðàìåòðîâ ñâàðî÷íîãî èñòî÷íèêà ïèòàíèÿ (ò.
å. ÷òî óñòðîéñòâî ðàáîòàåò áåç ïåðåãðóçêè).
Íèçêàÿ ýôôåêòèâíîñòü
ñâàðêè.
S Ïðîâåðüòå ïðàâèëüíîñòü ïîäñîåäèíåíèÿ êàáåëåé
ïîäà÷è ñâàðî÷íîãî òîêà è îáðàòíûõ êàáåëåé.
S Ïðîâåðüòå, ïðàâèëüíî ëè çàäàíà âåëè÷èíà òîêà.
S Óáåäèòåñü â òîì, ÷òî èñïîëüçóåòñÿ ïðîâîä òðåáóåìîãî
òèïà.
S Ïðîâåðüòå ñåòåâûå ïðåäîõðàíèòåëè.
RU
ba40d1ra -- 1 1 --
8 ÇÀÊÀÇ ÇÀÏÀÑÍÛÕ ×ÀÑÒÅÉ
Ðàáîòû ïî ðåìîíòó è ýëåêòðè÷åñêîìó ìîíòàæó äîëæíû âûïîëíÿòüñÿ
êâàëèôèöèðîâàííûì ñïåöèàëèñòîì ESAB .
Íåîáõîäèìî èñïîëüçîâàòü òîëüêî çàïàñíûå ÷àñòè, âûïóùåííûå ôèðìîé
ESAB.
Çàïàñíûå ÷àñòè ìîæíî çàêàçòú ó áëèæàéøåãî ê Âàì ESAB, (ñì. ïåðå÷åíú íà
ïîñëåäíåé ñòðàíèöå äàííîé áðîøþðû).
RU
ENGLISH
-- 1 2 --
TOCe
1 DIRECTIVE 13........................................................
2SAFETY 13...........................................................
3 INTRODUCTION 15...................................................
3.1 Equipment 15................................................................
4 TECHNICAL DATA 15.................................................
5 INSTALLATION 16....................................................
5.1 Location 16..................................................................
5.2 Mains power supply 17........................................................
6 OPERATION 17.......................................................
6.1 Connections and control devices 17............................................
6.2 Fan control 18...............................................................
6.3 Overheating protection 18.....................................................
7 MAINTENANCE 18....................................................
7.1 Inspection and cleaning 18....................................................
8 FAULT--TRACING 19..................................................
9 ORDERING SPARE PARTS 19..........................................
DIAGRAM 20............................................................
ORDERING NUMBER 22.................................................
ACCESSORIES 23.......................................................
-- 1 3 --
ba40d1ea
1DIRECTIVE
DECLARATION OF CONFORMITY
ESAB AB, Welding Equipment, SE--695 81 Laxå, Sweden, gives its unreserved guarantee that weld-
ing power source Mig L3000i from serial number 802 (2008 w.02) are constructed and tested in comp-
liance with the standard EN 60974--1 and EN 60974--10 (Class A) in accordance with the require-
ments of directive (2006/95/EC) and (2004/108/EEC).
-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --------
Kent Eimbrodt
Global Director
Equipment and Automation
Laxå 2008--01--04
2SAFETY
Users of ESAB welding equipment have the ultimate responsibility for ensuring that anyone who
works on or near the equipment observes all the relevant safety precautions. Safety precautions
must meet the requirements that apply to this type of welding equipment. The following recommen-
dations should be observed in addition to the standard regulations that apply to the workplace.
All work must be carried out by trained personnel well--acquainted with the operation of the welding
equipment. Incorrect operation of the equipment may lead to hazardous situations which can result
in injury to the operator and damage to the equipment.
1. Anyone who uses the welding equipment must be familiar with:
S its operation
S location of emergency stops
S its function
S relevant safety precautions
S welding
2. The operator must ensure that:
S no unauthorized person is stationed within the working area of the equipment when it is
started up.
S no--one is unprotected when the arc is struck
3. The workplace must:
S be suitable for the purpose
S be free from drafts
4. Personal safety equipment
S Always wear recommended personal safety equipment, such as safety glasses, flame--proof
clothing, safety gloves.
S Do not wear loose--fitting items, such as scarves, bracelets, rings, etc., which could become
trapped or cause burns.
5. General precautions
S Make sure the return cable is connected securely.
S Work on high voltage equipment may only be carried out by a qualified electrician.
S Appropriate fire extinquishing equipment must be clearly marked and close at hand.
S Lubrication and maintenance must not be carried out on the equipment during operation.
GB
-- 1 4 --
ba40d1ea
WARNING
Read and understand the instruction manual before installing or operating.
Arc welding and cutting can be injurious to yourself and others. Take precausions when welding.
Ask for your employer’s safety practices which should be based on manufacturers’ hazard data.
ELECTRIC SHOCK - Can kill
S Install and earth the welding unit in accordance with applicable standards.
S Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.
S Insulate yourself from earth and the workpiece.
S Ensure your working stance is safe.
FUMES AND GASES - Can be dangerous to health
S Keep your head out of the fumes.
S Use ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone
and the general area.
ARC RAYS - Can injure eyes and burn skin.
S Protect y our eyes and body. Use the correct welding screen and filter lens and wear protective
clothing.
S Protect bystanders with suitable screens or curtains.
FIRE HAZARD
S Sparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.
NOISE - Excessive noise can damage hearing
S Protect y our ears. Use earmuffs or other hearing protection.
S Warn bystanders of the risk.
MALFUNCTION - Call for expert assistance in the event of malfunction.
PROTECT YOURSELF AND OTHERS!
ESAB can provide you with all necessary welding p rotectio n and accessories.
WARNING!
Do not use the power source for thawing frozen pipes.
CAUTION!
Class A equipment is not intended for use in residential locations where
the electrical power is provided by the public low--voltage supply
system. There may be potential difficulties in ensuring electromagnic
compatibility of class A equipment in those locations, due to conducted
as well as radiated disturbances.
CAUTION!
This product is solely intended for arc welding.
CAUTION!
Read and understand the instruction manual before
installing or operating.
GB
-- 1 5 --
ba40d1ea
Do not dispose of electrical equipment together with normal waste!
In observance of European Directive 2002/96/EC on Waste Electrical and Electronic
Equipment and its implementation in accordance with national law, electrical equipment
that has reached the end of its life must be collected separately and returned to an
environmentally compatible recycling facility. As the owner of the equipment, you should
get information on approved collection systems from our local representative.
By applying this European Directive you will improve the environment and human
health!
3 INTRODUCTION
The Mig L3000i is a MIG/MAG welding power sour ce, which can also be used f or
MMA welding. The power source is used in combination with wire feed unit
Feed L3004.
All settings are adjusted from the wire feed unit.
ESAB’s accessories for the product can be found on page 23.
3.1 Equipment
Thepowersourceissuppliedwitha5mreturncableandaninstructionmanual.
4 TECHNICAL DATA
Mig L3000i
Mains voltage 400 V, ±10%, 3 50/60 Hz
Mains supply S
sc min
1.4 MVA
Primary current
I
max
MIG/MAG
I
max
MMA
16 A
19 A
No--load power demand when in the
energy--saving mode, 6.5 min. after welding
30 W
Setting range
MIG/MAG
MMA
8-- 48 V / 16-- 300 A
16--300 A
Permissible load at MIG/MAG
35% duty cycle
60% duty cycle
100% duty cycle
300 A / 29 V
240 A / 26 V
200 A / 24 V
Permissible load at MMA
30% duty cycle
60% duty cycle
100% duty cycle
300 A / 32 V
230 A / 29.2 V
190 A / 27.6 V
Power factor at maximum current
MIG/MAG
MMA
0.90
0.90
Efficiency at maximum current
MIG/MAG
MMA
85 %
84 %
Open --circuit voltage
MIG/MAG
MMA
70 -- 80 V
57 -- 67 V
GB
-- 1 6 --
ba40d1ea
Mig L3000i
Operating temperature -- 1 0 t o + 4 0 ˚C
Constant A--weighed sound pressure <70dB
Dimensions lxwxh 652 x 249 x 423 mm
Weight 29 kg
Insulation class transformer H
Enclosure class IP23C
Application class
Duty cycle
The duty cycle refers to the time as a percentage of a ten--minute period that you can weld at a cer-
tain load without overloading.
Enclosure class
The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid
objects or water. Equipment marked IP23 is designed for indoor and outdoor use.
Application class
The symbol indicates that the power source is designed for use in areas with increased
electrical hazard.
Mains supply, S
sc min
Minimum short circuit power on the network in accordance with IEC 61000--3--12
5 I NSTALLATION
The installatio n must be executed b y a p rofession al.
Note!
Mains supply requirements
High power equipment may, due to the primary current drawn from the mains supply, influence the
power quality of the grid. Therefore connection restrictions or requirements regarding the
maximum permissible mains impedance or the required minimum supply capacity at the interface
point to the public grid may apply for some types of equipment (see technical data). In this case it
is the responsibility of the installer or user of the equipment to ensure, by consultation with the
distrubution network operator if necessary, that the equipment may be connected.
5.1 Location
Position the welding power source such that its cooling air inlets and outlets are not
obstructed.
GB
-- 1 7 --
ba40d1ea
5.2 Mains power supply
Check that the welding power source is connected to the
correct mains power supply voltage, and that it is protected by
the correct fuse size. A protective earth connection must be
made in accordance with regulations.
Rating plate with supply connection data
Recommend ed fuse sizes an d minimum cable area
Mig L3000i MIG/MAG MMA
Mains voltage 400 V 3μ 50 Hz 400 V 3μ 50 Hz
Mains cable area mm
2
4G2.5 4G2.5
Phase current, I
eff
10 A 10 A
Fuse
Anti--surge
Type C MCB
16 A
16 A
16 A
16 A
Note! The mains cable areas and fuse sizes as shown above are in accordance with Swedish
regulations. Use the welding power source in accordance with the relevant national regulations.
Note! This welding power source is designed for connection to a four wire 230/400
volt system.
If the power source is to be used in a country with a higher mains voltage, the power
source shall be connected via a safety transformer.
6 OPERATION
General safety regulations for the handling of the equipment can be found on
page 13. Read through before you start using the equipment!
6.1 Connections and control devices
1 Connection for cooling unit, wire feed unit
or remote control unit
3 Connection for welding current cable (+)
(MMA welding)
2 Connection for return cable (--) 4 Mains voltage switch 1 / 0
GB
-- 1 8 --
ba40d1ea
6.2 Fan control
The power source has a time control that switches off the fans 6.5 minutes after
welding has stopped, the unit switches to energy--saving mode. The fans start again
when welding restarts.
The fans run at reduced speed for welding currents up to 110 A, and at full speed for
higher currents.
6.3 Overheating protection
The welding power source has overheating protection which operate if the
temperature becomes too high, When this occurs the welding current is interrupted
and a fault code is displayed on the control panel for the wire feed unit.
The overheating protection resets automatically when the temperature has fallen.
7 MAINTENANCE
Regular maintenance is important for safe, reliable operation.
Only those persons who have appropriate electrical knowledge (authorized
personnel) may remove the safety plates.
CAUTION!
All guarantee undertakings from the supplier cease to apply if the customer himself
attempts any work in the product during the guarantee period in order to rectify any faults.
7.1 Inspection and cleaning
Check r egularly that the welding power source is not clogged with dirt.
How often and which cleaning methods apply depend on: the welding process, arc
times, placement, and the surrounding environment. It is normally sufficient to blow
the dust out of the power source with dry compressed air (reduced pressure) once a
year.
Clogged or blocked air inlets and outlets otherwise result in overheating.
GB
-- 1 9 --
ba40d1ea
8 FAULT--TRACING
Try these recommended checks and inspections before sending for an authorised
service technician.
Type of fault Action
No arc. S Check that the mains power supply switch is turned on.
S Check that the welding current supply and return cables are
correctly connected.
S Check that the correct current value is set.
The welding current is
interrupted during welding.
S Check whether the overheating protection has operated (fault
code E6 is displayed on the control panel).
S Check the mains power supply fuses.
The overheating protection
cut--out frequently.
S Make sure that you are not exceeding the rated data for the
welding power source (i.e. that the unit is not being
overloaded).
Poor welding performance. S Check that the welding current supply and return cables are
correctly connected.
S Check that the correct current value is set.
S Check that the correct wire is being used.
S Check the mains power supply fuses.
9 ORDERING SPARE PARTS
Mig 3000i is designed and tested in accordance with the international and European
standards IEC/EN 60974--1 and EN 60974--10. It is the obligation of the service unit
which has carried out the service or repair work to make sure that the product still
conforms to the said standard.
Repair and electrical work should be performed by an authorized ESAB serviceman.
Use only ESAB original spare and wear parts.
Spare parts may be ordered through your nearest ESAB dealer, see the last page of
this publication.
GB
Edition 080328
Diagram Ñõåìà
-- 2 0 --
ba40e
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

ESAB Mig L3000i Origo™ Mig L3000i Manuale utente

Categoria
Sistema di saldatura
Tipo
Manuale utente