ESAB Tig 3000i Origo™ Tig 3000i Manuale utente
- Categoria
- Sistema di saldatura
- Tipo
- Manuale utente
Questo manuale è adatto anche per
Valid for serial no. 802--xxx--xxxx0459 943 127 100114
Tig 3000i
Origot
Instruction manual Èíñòðóêöèÿ ïî ýêñïëóàòàöèè
-- 2 --
Rights reserved to alter specifications without notice.
Îñòàâëÿåì çà ñîáîé ïðàâî èçìåíÿòü ñïåöèôèêàöèþ áåç ïðåäóïðåæäåíèÿ.
Ðóññêèé 3...............................................
ENGLISH 12..............................................
Ðóññêèé
TOCr
-- 3 --
1 ÒÅÕÍÈÊÀ ÁÅÇÎÏÀÑÍÎÑÒÈ 4........................................
2 ÂÂÅÄÅÍÈÅ 6.......................................................
2.1 Îáîðóäîâàíèå 6...........................................................
2.2 Ïóëüò óïðàâëåíèÿ 6........................................................
3 ÒÅÕÍÈ×ÅÑÊÈÅ ÕÀÐÀÊÒÅÐÈÑÒÈÊÈ 7................................
4ÓÑÒÀÍÎÂÊÀ 8.......................................................
4.1 Èíñòðóêöèè ïî ïîäúåìó 8..................................................
4.2 Ðàñïîëîæåíèå 8...........................................................
4.3 Ñåòü ýëåêòðîïèòàíèÿ 8.....................................................
5 ÏÐÀÂÈËÀ ÏÐÈÌÅÍÅÍÈß 9..........................................
5.1 Ñîåäèíåíèÿ è óñòðîéñòâà óïðàâëåíèÿ 9.....................................
5.2 Óïðàâëåíèå âåíòèëÿòîðàìè 10...............................................
5.3 Çàùèòà îò ïåðåãðåâà 10.....................................................
6 ÒÅÕÍÈ×ÅÑÊÎÅ ÎÁÑËÓÆÈÂÀÍÈÅ 10.................................
6.1 Ïðîâåðêà è ÷èñòêà 10.......................................................
7 ÏÎÈÑÊ È ÓÑÒÐÀÍÅÍÈÅ ÍÅÈÑÏÐÀÂÍÎÑ ÒÅÉ 11.......................
8 ÇÀÊÀÇ ÇÀÏÀÑÍÛÕ ×ÀÑÒÅÉ 11.......................................
ÑÕÅÌÀ 22..............................................................
ÍÎÌÅÐ ÇÀÊÀÇÀ 24.....................................................
ÄÎÏÎËÍÈÒÅËÜÍÛÅ ÏÐÈÍÀÄËÅÆÍÎÑÒÈ 25...........................
bt30d1ra -- 4 --
1 ÒÅÕÍÈÊÀ ÁÅÇÎÏÀÑÍÎÑÒÈ
Ïîëüçîâàòåëè ñâàðî÷íîãî îáîðóäîâàíèÿ ESAB îòâå÷àþò çà âûïîëíåíèå ïðàâèë òåõíèêè áåçîïàñíîñòè ëèöàìè,
ðàáîòàþùèìè íà îáîðóäîâàíèè è ðÿäîì ñ íèì. Ïðàâèëà òåõíèêè áåçîïàñíîñòè äîëæíû îòâå÷àòü òðåáîâàíèÿì ê
áåçîïàñíîé ýêñïëóàòàöèè ñâàðî÷íîãî îáîðóäîâàíèÿ ýòîãî òèïà. Ïîìèìî ñòàíäàðòíûõ ïðàâèë òåõíèêè
áåçîïàñíîñòè è îõðàíû òðóäà íà ðàáî÷åì ìåñòå ðåêîìåíäóåòñÿ ñëåäóþùåå.
Âñå ðàáîò û äîëæíû âûïîëíÿòüñÿ ïîäãîòîâëåííûìè ëèöàìè, çíàêîìûìè ñ ýêñïëóàòàöèåé ñâàðî÷íîãî
îáîðóäîâàíèÿ. Íåïðàâèëüíàÿ ýêñïëóàòàöèÿ îáîðóäîâàíèÿ ìîæåò âûçâàòü îïàñíûì ñèò óàöèè, ïð èâîäÿùèå ê
òðàâìèðîâàíèþ ïåðñîíàëà è ïîâðåæäåíèþ îáîðóäîâàíèÿ.
1. Bñå ëèöà, èñïîëüçóþùèå ñâàðî÷íîå îáîðóäîâàíèå, äîëæíû çíàòü:
S èíñòðóêöèè ïî ýêñïëóàòàöèè
S ðàñïîëîæåíèå îðãàíîâ àâàðèéíîãî îñòàíîâà
S íàçíà÷åíèå îáîðóäîâàíèÿ
S ïðàâèëà òåõíèêè áåçîïàñíîñòè
S òåõíîëîãèþ ñâàðêè
2. Îïåðàò îð îáåñïå÷èâàåò:
S óäàëåíèå ïîñòîðîííèõ ëèö èç ðàáî÷åé çîíû îáîðóäîâàíèÿ ïðè åãî çàïóñêå
S çàùèòó âñåõ ëèö îò âîçäåéñòâèÿ ñâàðî÷íîé äóãè
3. Ðàáî÷åå ìåñòî äîëæíî:
S îòâå÷àòü óñëîâèÿì ýêñïëóàòàöèè
S íå èìåòü ñêâîçíÿêîâ
4. Ñðåäñòâà çàùèòû ïåðñîíàëà
S Âî âñåõ ñëó÷àÿõ èñïîëüçóéòå ðåêîìåíäîâàííûå ñðåäñòâà èíäèâèäóàëüíîé çàùèòû, òàêèå êàê çàùèòíûå
î÷êè, îãíåñòîéêóþ îäåæäó, çàùèòíûå ïåð÷àòêè. Âíèìàíèå! Íå èñïîëüçóéòå çàùèòíûå ïåð÷àòêè ïðè
çàìåíå ïðîâîëîêè.
S Ïðè ñâàðêå çàïðåùàåòñÿ íîñèòü ñâîáîäíóþ îäåæäó, óêðàøåíèÿ è ò.ä., íàïðèìåð, øàðôû, áðàñëåòû,
êîëüöà, êîòîðûå ìîãóò ïîïàñòü â ñâàðî÷íîå îáîðóäîâàíèå èëè âûçâàòü îæîãè.
5. Îáùèå ìåðû ïðåäîñòîðîæíîñòè
S Ïðîâåðüòå íàäåæíîñòü ïîäêëþ÷åíèÿ îáðàòíîãî êàáåëÿ.
S Ðàáîòû íà îáîðóäîâàíèè ñ âûñîêèì íàïðÿæåíèåì äîëæíû ïðîèçâîäèòüñÿ òîëüêî
êâàëèôèöèðîâàííûì ýëåêòðèêîì.
S Â ïðåäåëàõ äîñòóïà äîëæíû íàõîäèòüñÿ ñîîòâåòñòâóþùèå ñðåäñòâà ïîæàðîòóøåíèÿ, èìåþùèå ÿñíóþ
ìàðêèðîâêó.
S Çàïðåùàåòñÿ ïð îâîäèòü ñìàçêó è òåõíè÷åñêîå îáñëóæèâàíèå îáîðóäîâàíèå âî âðåìÿ ýêñïëóàòàöèè.
RU
bt30d1ra -- 5 --
Ïåðåä íà÷àëîì ìîíòàæà è ýêñïëóàòàöèè âíèìàòåëüíî èçó÷èòå ñîîòâåòñòâóþùèå èíñòðóêöèè.
ÇÀÙÈÒÈÒÅ ÑÅÁß È ÄÐÓÃÈÕ!
ÂÍÈÌÀÍÈÅ!
Äóãoâaÿ câapêa è peçêa oïacíû êaê äëÿ ècïoëíèòeëÿ paáîò, òaê è äëÿ ïîcòopoííèõëèö. Tpeáyéte
coáëþäå íèå âñåõ ïðàâèë áåçîïàñíîñòè, äåéñòâóþùèõ íà îáúåêòå, êîòîðûå äîëæíû ó÷èòûâàòü
ñâåäåíèÿ îá îïàñíîñòÿõ, ïðåäñòàâëåííûå èçãîãîâèòåëåì ñâàð î÷íîãî îáîðóäîâàíèÿ.
ÎÏÀÑÍÎÑÒÜ ÑÌÅÐÒÅËÜÍÎÃÎ ÏÎÐÀÆÅÍÈß ÝËÅÊÒÐÈ×ÅÑÊÈÌ ÒÎÊÎÌ.
S Ñâàðî÷íûé àãðåãàò óñòàíàâëèâàåòñÿ è çàçåìëÿåòñÿ â ñîîòâåòñòâèè ñ äåéñ òâóþùèìè íîðìàìè è
ïðàâèëàìè.
S Íå äîïóñêàéòå ê îíò àêòà íàõîäÿùèõñÿ ïîä íàïðÿæåíèåì äåòàëåé è ýëåêòðîäîâ ñ íåçàùèùåííûìè
÷àñòÿìèòåëà,ìîêðûìèðóêàâèöàìèèìîêðîéîäåæäîé.
S Îáåñïå÷üò å ýëåêòðè÷åñêóþ èçîëÿöèþ îò çåìëè è ñâàðèâàåìûõ äåòàëåé.
S Îáåñïå÷üòå ñî áëþäåíèå áåçîïàñíûõ ðàáî÷èõ ðàññòîÿíèé.
ÄÛÌÛ È ÃÀÇÛ ìîãóò áûòü îïàñíû äëÿ ÷åëîâåêà
S Èñêëþ÷èòå âîçìî æíîñòü âîçäåéñòâèÿ äûìîâ.
S Äëÿ èñêëþ÷åíèÿ âäûõàíèÿ äûìîâ âî âðåìÿ ñâàðêè îðãàíèçóåòñÿ îáùàÿ âåíòèëÿöèÿ ïîìåùåíèÿ, à
òàêæåâûòÿæíàÿâåíòèëÿöèÿèççîíûñâàðêè.
ÈÇËÓ×ÅÍÈÅ ÄÓÃÈ âûçûâàåò ïîðàæåíèå ãëàç è îæîãè êîæè.
S Çàùèòèòå ãëàçà è êîæó. Äëÿ ýòîã î èñïîëüçóéòå çàùèòíûå ùèòêè, öâåòíûå ëèíçû è çàùèòíóþ
ñïåöîäåæäó.
S Äëÿ çàùèòû ïîñ òîðîííèõ ëèö ïðèìåíÿþòñÿ çàùèòíûå ýêðàíû èëè çàíàâåñè.
ÏÎÆÀÐÎÎÏÀÑÍÎÑÒÜ
S Èñêðû (áðûçãè ìåòàëëà) ìîãóò âûçâàòü ïîæàð. Óáåäèòåñü â îòñóòñòâèè ãîðþ÷èõ ìàòåðèàëîâ
ïîáëèçîñòè îò ìåñòà ñâàðêè.
ØÓÌ - ×ðåçìåðíûé øóì ìîæåò ïðèâåñòè ê ïîâðåæäåíèþ îðãàíîâ ñëóõà
S Ïðèìèòå ìåðû äëÿ çàùèòû ñëóõà. Èñïîëüçóéòå çàòû÷êè äëÿ óøåé èëè äðóãèå ñðåäñòâà çàùèòû
ñëóõà.
S Ïðåäóïðåäèòå ïîñòîðîííèõ ëèö îá îïàñíîñòè.
ÍÅÈÑÏÐÀÂÍÎÑÒÈ - Ïðè íåèñïðàâ íîñòè îáðàòèòåñü ê ñïåöèàëèñòàì ïî ñâàðî÷íîìó
îáîðóäîâàíèþ
Êîìïàíèÿ ESAB ãîòîâà ïðåäîñòàâèòü âàì âñå çàùèòíîå ñíàðÿæåíèå è
ïðèíàäëåæíîñòè, íå îáõîäèìûå äëÿ âûïîëíåíèÿ ñâàðî÷íûõ ðàáîò .
ÂÍÈÌÀÍÈÅ!
Çàïðåùàåòñÿ èñïîëüçîâàòü èñòî÷íèê ïèòàíèÿ äëÿ îòòàèâàíèÿ òðóá.
ÎÑÒ ÎÐÎÆÍÎ!
Îáîðóäîâàíèå Class À íå ïðåäíàçíà÷å íî äëÿ èñïîëüçîâàíèÿ â
æèëûõ ïîìåùåíèÿõ, ãäå ýëåêòðîñíàáæåíèå îñóùåñòâëÿåòñÿ èç
áûòîâûõ ñåòåé íèçêîãî íàïðÿæåíèÿ. Â òàêèõ ìåñòàõ ìîãóò
ïîÿâèòüñÿ ïîòåíöèàëüíûå òðó äíîñòè îáåñïå÷åíèå
ýëåêòðîìàãíèòíîé ñîâìåñòèìîñòè îáîðóäîâàíèÿ Class À
âñëåäñòâèå êîíäóêòèâíûõ è ðàäèàöèîííûõ ïîìåõ.
Äàííîå èçäåëèå ïðåäíàçíà÷åíî òîëüêî äëÿ äóãîâîé ñâàðêè.
RU
bt30d1ra -- 6 --
ÎÑÒ ÎÐÎÆÍÎ!
Ïåðåä íà÷àëîì ìîíòàæà è ýêñïëóàòàöèè
âíèìàòåëüíî è çó÷èòå ñîîòâåòñòâóþùèå
èíñòðóêöèè.
2 ÂÂÅÄÅÍÈÅ
Tig 3000i ïðåäñòàâëÿåò ñîáîé èñòî÷íèê ïèòàíèÿ äëÿ äóãîâîé ñâàðêè
âîëüôðàìîâûì ýëåêòðîäîì â çàùèòíîì ãàçå (TIG), êîòîðûé ìîæíî òàêæå
èñïîëüçîâàòü ä ëÿ ðó÷íîé äóãîâîé ñâàðêè ìåòàëëè÷åñêèì ïëàâÿùèìñÿ
ýëåêòðîäîì (MMA).
Àêñåññóàðû îò äëÿ èçäåëÿ ìîæíî íàéòè íà ñòðíèöå 25.
2.1 Îáîðóäîâàíèå
 êîìïëåêò ïîñòàâêè âõîäÿò:
ðóêîâîäñòâî ê ñâàðî÷íîìó èñòî÷íèêó ïèòàíèÿ, ðóêîâîäñòâî ê ïóëüòó
óïðàâëåíèÿ è 5 ì îáðàòíîãî ïðîâîäà.
2.2 Ïóëüò óïðàâëåíèÿ
Áëîêè ïîñòàâëÿþòñÿ â êîìïëåêòå ñ îäíèì èç ñëåäóþùèõ ïóëüòîâ óïðàâëåíèÿ:
TA23 TA24
Ïîäðîáíîå îïèñàíèå ïóëüòà óïðàâëåíèÿ ïðèâåäåíî â îòäåëüíîì ðóêîâîäñòâå
ïî ýêñïëóàòàöèè.
RU
bt30d1ra -- 7 --
3 ÒÅÕÍÈ×ÅÑÊÈÅ ÕÀÐÀÊÒÅÐÈÑÒÈÊÈ
Tig 3000i
Íàïðÿæåíèå ñåòè 400 Â, ↓10%, 3∼ 50/60 Ãö
Ïèòàíèå îò ñåòè S
sc min
1,4 MVA
Ïåðâè÷íûé òîê
I
ìàêñ.
TIG
I
ìàêñ.
MMA
14. 1 A
19 A
Ïîòðåáëÿåìàÿ ìîùíîñòü õîëîñòîãî õîäà â
ðåæèìå ýíåðãîñáåðåæåíèÿ, 6,5 ìèí ïîñëå
ñâàðêè
30 Âò
Äèàïàçîí óñòàâîê
MMA
TIG
16-300 À
4-300 À
Äîïóñòèìàÿ íàãðóçêà ïðè ñâàðêå TIG
ÏÂ 35%
ÏÂ 60%
ÏÂ 100%
300 À / 22 Â
240À/19,6Â
200 À / 18 Â
Äîïóñòèìàÿ íàãðóçêà ïðè ñâàðêå MMA
ÏÂ 30%
ÏÂ 60%
ÏÂ 100%
300 À / 32 Â
230 À / 29,2 Â
190À/27,6Â
Êîýôôèöèåíò ìîùíîñòè ïðè
ìàêñèìàëüíîì òîêå
TIG
MMA
0.89
0.90
Êïä ïðè ìàêñèìàëüíîì òîêå
TIG
MMA
81. 5 %
84 %
Íàïðÿæåíèå õîëîñòîãî õîäà
MMA
57 -67 Â
Ðàáî÷àÿ òåìïåðàò óðà îò -10 äî +40˚C
Òåìïåðàòóðà ïðè òðàíñïîðòèðîâêå îò -20 äî +55˚C
Ïîñòîÿííûé ýêâèâàëåíòíûé óðîâåíü
çâóêîâîãî äàâëåíèÿ ïî øêàëå À
<70äÁ
Ðàçìåðû, ä x ø x â 652 x 2 49 x 423 ìì
Ìàññà 32.5 êã
Êëàññ èçîëÿöèè òðàíñôîðìàòîðà H
Ê ëàññ çàùèòû IP 23
Êëàññ ïðèìåíåíèÿ
Ðàáî÷èé öèêë
Ðàáî÷èé öèêë ïðåäñòàâëÿåò ñîáîé äîëþ (â %%) äåñÿòèìèíóòíîãî èíòåðâàëà, â òå÷åíèå
êîòîðîé ìîæíî ïðîèçâîäèòü ñâàðêó ïðè îïðåäåëåííîé íàãðóçêå áåç ïåðåãðóçêè. Ðàáî÷èé
öèê ë óêàçàí äëÿ òåìïåðàòóðû 40˚C.
Êëàññ êîæóõà
Íîðìû IP óêàçûâàþò êëàññ êîæóõà, ò.å., ñòåïåíü çàùèòû îò ïðîíèêíîâåíèÿ òâåðäûõ
îáúåêòîâ è âîäû. Îáîðóäîâàíèå ñ ìàðêèðîâêîé IP 23 ïðåäíàçíà÷åíî äëÿ íàðóæíîé è
âíóòðåííåé óñòàíîâêè.
Ê ëàññ çîíû óñòàíîâêè
Ýòîò ñèìâîë îçíà÷àåò, ÷òî èñòî÷íèê ïèòàíèÿ ïðåäíàçíà÷åí äëÿ èñïîëüçîâàíèÿ â çîíàõ
ñ ïîâûøåííîé îïàñíîñòüþ ïîðàæåíèÿ ýëåêòðî òîê îì.
RU
bt30d1ra -- 8 --
Ïèòàíèå îò ñåòè, S
sc ìèí.
Ìíèìà ëüíàÿ ìîùíîñòü ïðè êîðîòêîì çàìûêàíèè ñåòè â ñîîòâåòñòâèè ñî ñòàíäàðòîì IEC
61000-3-12
4ÓÑÒÀÍÎÂÊÀ
Ââîä â ýêñïëóàòàöèþ äîëæåí ïðîèçâîäèòüñÿ êâàëèôèöèðîâàííûì
ñïåöèàëèñòîì.
Ïðèìe÷aíèå!
Òðåáîâàíèÿ ê ñåòÿì ýëåêòðîñíàáæåíèÿ
Èç-çà áîëüøèõ âåëè÷èí òîêà â ïåðâè÷íîé îáìîòêå îáîðóäîâàíèå âûñîêîé ìîùíîñòè
ìîæåò ñóùåñòâåííî ïîâëèÿòü íà ìîùíîñòíûå õàðàêòåðèñòèêè ñåòè. Ïîýòîìó â îòíîøåíèè
íåêîòîðîãî îáîðóäîâàíèÿ ïðèìåíÿþòñÿ îãðàíè÷åíèÿ èëè äîïîëíèòåëüíûå òðåáîâàíèÿ,
êàñàþùèåñÿ ìàêñèìàëüíî äîïóñòèìîãî ñîïðîòèâëåíèÿ îáîðóäîâàíèÿ èëè ìèíèìàëüíîé
ñïîñîáíîñòè îáåñïå÷èòü ñòàáèëüíîå ýíåðãîñíàáæåíèå â òî÷êà õ âçàèìîäåéñòâèÿ
îáùåñòâåííûõ ñåòåé.  òàêîì ñëó÷àå ïîëüçîâàòåëü îáîðóäîâàíèÿ èëè òîò, êòî åãî
óñòàíàâëèâàåò, äîëæåí ïðîêîíñóëüòèðîâàòüñÿ ñ îïåðàòîðîì ýíåðãîñåòè ïî ïîâîäó
âîçìî æíîñòè ïîäêëþ÷åíèÿ òàêîãî ðîäà îáîðóäîâàíèÿ.
4.1 Èíñòðóêöèè ïî ïîäúåìó
4.2 Ðàñïîëîæåíèå
Óñòàíîâèòå ñâàðî÷íûé èñòî÷íèê ïèòàíèÿ òàêèì îáðàçîì, ÷òîáû åãî
âîçäóõîçàáîðíûå è âûïóñêíûå îòâåðñòèÿ íå áûëè çàãðàæäåíû.
4.3 Ñåòü ýëåêòðîïèòàíèÿ
Óáåäèòåñü â òîì, ÷ò î áëîê ïîäêëþ÷åí ê ñå òè
ýëåêòðîïèòàíèÿ ñ òðåáóåìûì íàïðÿæåíèåì è çàùèùåí
ïðåäîõðàíèòåëÿìè òðåáóåìîãî íîìèíàëà. Íåîáõîäèìî
îáåñïå÷èòü çàùèòíîå çàçåìëåíèå â ñîîòâåòñòâèè ñ
äåéñòâóþùèìè íîðìàìè.
Ïàñïîðòíàÿ òàáëè÷êà ñ ïàðàìåòðàìè ñåòè ýëåêòðîïèòàíèÿ.
RU
bt30d1ra -- 9 --
Ðåêîìåíäóåìûå íîìèíà ëû ïðå äîõðàíèòåëåé è ìèíèìàëüíûå ñå÷åíèÿ
êàáåëåé
Tig 3000i TIG MMA
Íàïðÿæåíèå ñåòè 400 Â 3μ 50 Ãö 400 Â 3μ 50 Ãö
Ñå÷åíèå êàáåëÿ ïèòàíèÿ,
ìì
2
4G2,5 4G2,5
Ôàçíûé òîê, I
1eff
8A 13 A
Ïðåäîõðàíèòåëü
óñòîé÷èâûé ê
ïåðåíàïðÿæåíèÿì
òèï C MCB
10 A
16 A
16 A
16 A
Âíèìàíèå! Ïðèâåäåííûå âûøå ñå÷åíèÿ ñèëîâûõ êàáåëåé è íîìèíàëû ïðåäî õðàíèòåëåé
ñîîòâåòñòâóþò øâåäñêèì íîðìàì. Ýêñïëóàòàöèÿ èñòî÷íèêà ñâàðî÷íîãî òîêà äîëæíà
îñóùåñòâëÿòüñÿ â ñîîòâåòñòâèè ñ äåéñòâóþùèìè íàöèîíàëüíûìè íîðìàòèâíûìè
äîêóìåíòàìè.
Âíèìàíèå!Ýòîò èñòî÷íèê ñâàðî÷íîãî òîêà ðàññ÷èòàí íà ïîäê ëþ÷åíèå ê
÷åòûðåõïðîâîäíîé ñèñòåìå c íàïðÿæ åíèåì 230/400 Âîëüò.
Åñëè èñòî÷íèê ïèòàíèÿ ïðåäïîëàãàåòñÿ èñïîëüçîâàòü â ñòðàíå ñ áîëåå
âûñîêèì ñåòåâûì íàïðÿæåíèåì, èñòî÷íèê ïèòàíèÿ íóæíî ïîäêëþ÷àòü ÷åðåç
òðàíñôîðìàòîð áåçîïàñíîñòè.
5 ÏÐÀÂÈËÀ ÏÐÈÌÅÍÅÍÈß
Îáùèå ïðàâèëà òåõíèêè áåçîïàñíîñòè ïðè ðàáîòå ñ îáîðóäîâàíèåì
ïðèâîäÿòñÿ íà ñòð. 4. Ïðî÷òèòå èõ äî èñïîëüçîâàíèÿ îáîðóäîâàíèÿ!
5.1 Ñîåäèíåíèÿ è óñòðîéñòâà óïðàâëåíèÿ
1 Ïóëüò óïðàâëåíèÿ,
ñì. îòäåëüíîå ðóêîâîäñòâî ïî
ýêñïëóàòàöèè
5 Ñîåäèíèòåëü äëÿ ñâàðî÷íîãî êàáåëÿ (-)
èëè ñâàðî÷íîé ãîðåëêè
2 Ñîåäèíèòåëü CAN äëÿ áëîêà
îõëàæäåíèÿ èëè áëîêà äèñòàíöèîííîãî
óïðàâëåíèÿ
6 Ñîåäèíèòåëü äëÿ îáðàòíîãî êàáåëÿ (+)
3 Ãíåçäî äëÿ ñèãíàëà ïóñêà îò ñâàðî÷íîé
ãîðåëêè
7 Âûêëþ÷àòåëü ïèòàíèÿ
4 Øòóöåðäëÿïîäà÷èãàçàêñâàðî÷íîé
ãîðåëêå
8 Øòóöåð ä ëÿ çàùèòíîãî ãàçà
RU
bt30d1ra -- 1 0 --
5.2 Óïðàâëåíèå âåíòèëÿòîðàìè
Èñòî÷íèê ïèòàíèÿ îñíàùåí òàéìåðîì, îáåñïå÷èâàþùèì ïðîäîëæåíèå ðàáîòû
âåíòèëÿòîðîâ â òå÷åíèå 6,5 ìèí ïîñëå ïðåêðàùåíèÿ ñâàðêè, è ïåðåê ëþ÷åíèå
áëîêà â ðåæèì ýíåðãîñáåðåæåíèÿ. Ïðè âîçîáíîâëåíèè ñâàðêè âåíòèëÿòîðû
çàïóñêàþ òñÿ âíîâü.
Âåíòèëÿòîðû ðàáîòàþò íà ïîíèæåííûõ îáîðîòàõ ïðè ñâàðî÷íûõ òîêàõ äî 110 A
èíàïîëíûõîáîðîòàõïðèáîëüøèõòîêàõ.
5.3 Çàùèòà îò ïåðåãðåâà
Ñâàðî÷íûé èñòî÷íèê ïèòàíèÿ èìååò çàùèòó îò ïåðåãðåâà, ñðàáàòûâàþùóþ,
êîãäà ò åìïåðàòóðà ñòàíîâèòñÿ ñëèøêîì âûñîêîé. Ïðè ýòîì ïîäà÷à ñâàðî÷íîãî
òîêà ïðåêðàùàåòñÿ è íà ïóëüò óïðàâëåíèÿ âûâîäèòñÿ êîä íåèñïðàâíîñòè.
Ïîñëå ñíèæåíèÿ òåìïåðàòóðû çàùèòà îò ïåðåãðåâà àâòîìàòè÷åñêè
âîçâðàùàåòñÿ â èñõîäíîå ïîëîæåíèå.
6 ÒÅÕÍÈ×ÅÑÊÎÅ ÎÁÑËÓÆÈÂÀÍÈÅ
Ðåãóëÿðíîå òåõíè÷åñêîå îáñëóæèâàíèå èìååò âàæíîå çíà÷åíèå äëÿ
îáåñïå÷åíèÿ áåçîïàñíîñòè è íàäåæíîñòè.
Äàííîå èçäåëèå ïðåäíàçíà÷åíî òîëüêî äëÿ äóãîâîé ñâàðêè.
Òîëüêî ëèöà, èìåþùèå êâàëèôèêàöèþ ýëåêòðèêà (àòòåñòîâàííûé ïåðñîíàë),
èìåþò ïðàâî ñíèìàòü ïàíåëè, îáåñïå÷èâàþùèå áåçîïàñíîñòü ð àáîòû.
6.1 Ïðîâåðêà è ÷èñòêà
Èñòî÷íèê ïèòàíèÿ
Ðåãóëÿðíî ñëåäèòå çà òåì, ÷òîáû ñâàðî÷íûé èñòî÷íèê ïèòàíèÿ íå áûë çàáèò
ãðÿçüþ.
Ïåðèîäè÷íîñòü è ïðèìåíÿåìûå ìåòîäû ÷èñòêè çàâèñÿò îò òåõíîëîãèè ñâàðêè,
ä ëèòåëüíîñòè ãîðåíèÿ äóãè è óñëîâèé îêðóæàþùåé ñðåäû. Îáû÷íî áûâàåò
äîñòàòî÷íî ïðîäóâàòü è ñòî÷íèê ïèòàíèÿ ñóõèì ñæàòûì âîçäóõîì (ïðè
ïîíèæåííîì äàâëåíèè) îäèí ðàç â ãîä.
Çàñîðåííûå èëè çàêóïîðåííûå îòâåðñòèÿ äëÿ ïîäâîäà è îòâîäà âîçäóõà òàêæå
ìîãóò ñòàòü ïðè÷èíîé ïåðåãðåâà óñòðîéñòâà.
Ñâàðî÷íàÿ ãîðåëêà
Äëÿ îáåñïå÷åíèÿ íà äåæíîé ñâàðêè íåîáõîäèìî ÷åðåç ðåãóëÿðíûå
ïðîìåæóòêè âðåìåíè ÷èñòèòü è çàìåíÿòü áûñòðîèçíàøèâàåìûå äåòàëè
ñâàðî÷íîé ãîðåëêè.
RU
bt30d1ra -- 1 1 --
7 ÏÎÈÑÊ È ÓÑÒÐÀÍÅÍÈÅ ÍÅÈÑÏÐÀÂÍÎÑÒÅÉ
Ïðåæäå ÷åì âûçûâàòü óïîëíîìî÷åííîãî ñïåöèàëèñòà ïî îáñëóæèâàíèþ,
ïîïðîáóéòå ñàìîñòîÿòåëüíî âûïîëíèòü ðåêîìåíäóåìûå íèæå ïðîâåðêè.
Òèï íåèñïðàâíîñòè Ðåêîìåíäóåìûå ìåðû
Îòñóòñòâèå äóãè S Ïðîâåðüòå, âêëþ÷åí ëè âûêëþ÷àòåëü ïèòàíèÿ.
S Ïðîâåðüòå ïðàâèëüíîñòü ïîäêëþ÷åíèÿ ñâàðî÷íîãî è
îáðàòíîãî ïðîâîäà.
S Ïðîâåðüòå, ïðàâèëüíî ëè çàäàíà â åëè÷èíà òîêà.
 ïðîöåññå ñâàðêè ïðîïàë
ñâàðî÷íûé òîê.
S Ïðîâåðüòå, íå ñðàáîòàëà ëè çàùèòà îò ïåðåãðåâà (íà
ïóëüò óïðàâëåíèÿ âûâîäèòñÿ êîä îòêàçà E6).
S Ïðîâåðüòå ïðåäîõðàíèòåëè â öåïè ïèòàíèÿ.
×àñòî ñðàáàòûâàåò òåïëî âàÿ
çàùèòà.
S Óáåäèòåñü â òîì, ÷òî íå ïðåâûøåíû íîìèíàëüíûå
çíà÷åíèÿ ïàðàìåòðîâ ñâàðî÷íîãî èñòî÷íèêà ïèòàíèÿ (ò.
å. ÷òî óñòðîéñòâî ðàáîòàåò áåç ïåðåãðóçêè).
Ïëîõîå êà÷åñòâî ñâàðêè. S Ïðîâåðüòå ïðàâèëüíîñòü ïîäêëþ÷åíèÿ ñâàðî÷íîãî è
îáðàòíîãî ïðîâîäà.
S Ïðîâåðüòå, ïðàâèëüíî ëè çàäàíà â åëè÷èíà òîêà.
S Óáåäèòåñü â òîì, ÷òî èñïîëüçóþòñÿ ýëåêòðîäû
òðåáóåìîãî òèïà.
S Ïðîâåðüòå ïðåäîõðàíèòåëè â öåïè ïèòàíèÿ.
8 ÇÀÊÀÇ ÇÀÏÀÑÍÛÕ ×ÀÑÒÅÉ
Çàïàñíûå ÷àñòè ìîæíî çàêàçòú ó áëèæàéøåãî ê Âàì ESAB, (ñì. ïåðå÷åíú íà
ïîñëåäíåé ñòðàíèöå äàííîé áðîøþðû).
RU
ENGLISH
-- 1 2 --
TOCe
1 DIRECTIVE 13........................................................
2SAFETY 13...........................................................
3 INTRODUCTION 15...................................................
3.1 Equipment 15................................................................
3.2 Control panel 15.............................................................
4 TECHNICAL DATA 16.................................................
5 INSTALLATION 17....................................................
5.1 Lifting instruction 17..........................................................
5.2 Location 17..................................................................
5.3 Mains power supply 17........................................................
6 OPERATION 18.......................................................
6.1 Connections and control devices 18............................................
6.2 Fan control 18...............................................................
6.3 Overheating protection 18.....................................................
7 MAINTENANCE 19....................................................
7.1 Inspection and cleaning 19....................................................
8 FAULT--TRACING 19..................................................
9 ORDERING SPARE PARTS 20..........................................
DIAGRAM 22............................................................
ORDERING NUMBER 24.................................................
ACCESSORIES 25.......................................................
-- 1 3 --
bt30d1ea
1DIRECTIVE
DECLARATION OF CONFORMITY
ESAB AB, Welding Equipment, SE--695 81 Laxå, Sweden, gives its unreserved guarantee that weld-
ing power source Tig 3000i from serial number 802 are constructed and tested in compliance with the
standard EN 60974--1 /--3 and EN 60974--10 (Class A) in accordance with the requirements of direc-
tive (2006/95/EC) and (2004/108/EEC).
-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --------
Kent Eimbrodt
Global Director
Equipment and Automation
Laxå 2008--01--04
2SAFETY
Users of ESAB welding equipment have the ultimate responsibility for ensuring that anyone who
works on or near the equipment observes all the relevant safety precautions. Safety precautions
must meet the requirements that apply to this type of welding equipment. The following recommen-
dations should be observed in addition to the standard regulations that apply to the workplace.
All work must be carried out by trained personnel well--acquainted with the operation of the welding
equipment. Incorrect operation of the equipment may lead to hazardous situations which can result
in injury to the operator and damage to the equipment.
1. Anyone who uses the welding equipment must be familiar with:
S its operation
S location of emergency stops
S its function
S relevant safety precautions
S welding
2. The operator must ensure that:
S no unauthorized person is stationed within the working area of the equipment when it is
started up.
S no--one is unprotected when the arc is struck
3. The workplace must:
S be suitable for the purpose
S be free from drafts
4. Personal safety equipment
S Always wear recommended personal safety equipment, such as safety glasses, flame--proof
clothing, safety gloves. Note! Do not use safety gloves when replacing wire.
S Do not wear loose--fitting items, such as scarves, bracelets, rings, etc., which could become
trapped or cause burns.
5. General precautions
S Make sure the return cable is connected securely.
S Work on high voltage equipment may only be carried out by a qualified electrician.
S Appropriate fire extinquishing equipment must be clearly marked and close at hand.
S Lubrication and maintenance must not be carried out on the equipment during operation.
GB
-- 1 4 --
bt30d1ea
WARNING
Read and understand the instruction manual before installing or operating.
Arc welding and cutting can be injurious to yourself and others. Take precausions when welding.
Ask for your employer’s safety practices which should be based on manufacturers’ hazard data.
ELECTRIC SHOCK - Can kill
S Install and earth the welding unit in accordance with applicable standards.
S Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.
S Insulate yourself from earth and the workpiece.
S Ensure your working stance is safe.
FUMES AND GASES - Can be dangerous to health
S Keep your head out of the fumes.
S Use ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone
and the general area.
ARC RAYS - Can injure eyes and burn skin.
S Protect y our eyes and body. Use the correct welding screen and filter lens and wear protective
clothing.
S Protect bystanders with suitable screens or curtains.
FIRE HAZARD
S Sparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.
NOISE - Excessive noise can damage hearing
S Protect y our ears. Use earmuffs or other hearing protection.
S Warn bystanders of the risk.
MALFUNCTION - Call for expert assistance in the event of malfunction.
PROTECT YOURSELF AND OTHERS!
ESAB can provide yo u with all necessary welding protection an d accessories.
WARNING!
Do not use the power source for thawing frozen pipes.
CAUTION!
Class A equipment is not intended for use in residential locations where
the electrical power is provided by the public low--voltage supply
system. There may be potential difficulties in ensuring electromagnetic
compatibility of class A equipment in those locations, due to conducted
as well as radiated disturbances.
CAUTION!
This product is solely intended for arc welding.
CAUTION!
Read and understand the instruction manual before
installing or operating.
GB
-- 1 5 --
bt30d1ea
Do not dispose of electrical equipment together with normal waste!
In observance of European Directive 2002/96/EC on Waste Electrical and Electronic
Equipment and its implementation in accordance with national law, electrical equipment
that has reached the end of its life must be collected separately and returned to an
environmentally compatible recycling facility. As the owner of the equipment, you should
get information on approved collection systems from our local representative.
By applying this European Directive you will improve the environment and human
health!
3 INTRODUCTION
The Tig 3000i is a TIG welding power source, which can also be u sed for MMA
welding.
ESAB’s accessories for the product can be found on page 25.
3.1 Equipment
The power sources is supplied with:
Instruction manual for the welding power source, instruction manual for the control
panel and 5 m return cable.
3.2 Control panel
The units are supplied with one of the following control panels:
TA23 TA24
See the separate instruction manual for a detailed description of the control panel.
GB
-- 1 6 --
bt30d1ea
4 TECHNICAL DATA
Tig 3000i
Mains voltage 400 V, ±10%, 3∼ 50/60 Hz
Mains supply S
sc min
1,4 MVA
Primary current
I
max
TIG
I
max
MMA
14.1 A
19 A
No--load power demand when in the
energy--saving mode, 6.5 min. after welding
30 W
Setting range
MMA
TIG
16--300 A
4--300 A
Permissible load at TIG
35% duty cycle
60% duty cycle
100% duty cycle
300 A / 22 V
240 A / 19.6 V
200 A / 18 V
Permissible load at MMA
30% duty cycle
60% duty cycle
100% duty cycle
300 A / 32 V
230 A / 29.2 V
190 A / 27.6 V
Power factor at maximum current
TIG
MMA
0.89
0.90
Efficiency at maximum current
TIG
MMA
81.5 %
84 %
Open --circuit voltage
MMA
57-- 67 V
Operating temperature -- 1 0 t o + 4 0 ˚C
T ransportation temperature -- 2 0 t o + 5 5 ˚C
Constant A--weighted sound pressure <70dB
Dimensions lxwxh 652 x 249 x 423 mm
Weight 32.5 kg
Insulation class transformer H
Enclosure class IP 23
Application class
Duty cycle
The duty cycle refers to the time as a percentage of a ten--minute period that you can weld at a cer-
tain load without overloading. The duty cycle is valid for 40˚C.
Enclosure class
The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid
objects or water. Equipment marked IP23 is designed for indoor and outdoor use.
Application class
The symbol indicates that the power source is designed for use in areas with increased
electrical hazard.
Mains supply, S
sc min
Minimum short circuit power on the network in accordance with IEC 61000--3--12
GB
-- 1 7 --
bt30d1ea
5 I NSTALLATION
The installatio n must be executed by a professional.
Note!
Mains supply requirements
High power equipment may, due to the primary current drawn from the mains supply, influence the
power quality of the grid. Therefore connection restrictions or requirements regarding the
maximum permissible mains impedance or the required minimum supply capacity at the interface
point to the public grid may apply for some types of equipment (see technical data). In this case it
is the responsibility of the installer or user of the equipment to ensure, by consultation with the
distrubution network operator if necessary, that the equipment may be connected.
5.1 Lifting instruction
5.2 Location
Position the welding power source such that its cooling air inlets and outlets are not
obstructed.
5.3 Mains power supply
Check that the welding power source is connected to the
correct mains power supply voltage, and that it is protected by
the correct fuse size. A protective earth connection must be
made in accordance with r egulations.
Rating plate with supply connection data
Recommend ed fuse sizes and minimum cable area
Tig 3000i TIG MMA
Mains voltage 400 V 3μ 50 Hz 400 V 3μ 50 Hz
Mains cable area mm
2
4G2,5 4G2,5
Phase current I
1eff
8A 13 A
Fuse
anti--surge
type C MCB
10 A
16 A
16 A
16 A
GB
-- 1 8 --
bt30d1ea
Note! The mains cable areas and fuse sizes as shown above are in accordance with Swedish
regulations. Use the welding power source in accordance with the relevant national regulations.
Note! The welding power source is designed for connection to a 230 / 400 volt
system with four conductors.
If the power source is to be used in countries with a higher supply voltage, the power
source must be connected via a safety transformer.
6 OPERATION
General safety regulations for the handling of the equipment can be found on
page 13. Read through before you start using the equipment!
6.1 Connections and control devices
1 Control panel,
see separate instruction manual
5 Connection for welding cable (--) or
welding torch
2 CAN connection for cooling unit or remote
control unit
6 Connection for return cable (+)
3 Connection for start signal from the
welding torch
7 Mains voltage switch
4 Connection for gas to the torch 8 Connection for shielding gas
6.2 Fan control
The power source has a time control that means that the fans continue to run for 6.5
minutes after welding has stopped, and the unit switches to energy--saving mode.
The fans start again when welding r estarts.
The fans run at reduced speed for welding currents up to 110 A, and at full speed for
higher currents.
6.3 Overheating protection
The welding power source has overheating protection that operates if the
temperature becomes too high. When this occurs the welding current is interrupted
and a fault code is displayed on the control panel.
The overheating protection resets automatically when the temperature has fallen.
GB
-- 1 9 --
bt30d1ea
7 MAINTENANCE
Regular maintenance is important for safe, reliable operation.
CAUTION!
All guarantee undertakings from the supplier cease to apply if the customer himself
attempts any work in the product during the guarantee period in order to rectify any faults.
Only those persons who have appropriate electrical knowledge (authorized
personnel) may remove the safety plates.
7.1 Inspection and cleaning
Power source
Check r egularly that the welding power source is not clogged with dirt.
How often and which cleaning methods apply depend on: the welding process, arc
times, placement, and the surrounding environment. It is normally sufficient to blow
down the power source with dry compressed air (reduced pressure) once a year.
Clogged or blocked air inlets and outlets otherwise r esult in overheating.
Welding torch
The welding torch’s wear parts should be cleaned and replaced at regular intervals in
order to achieve trouble--free welding.
8 FAULT--TRACING
Try these recommended checks and inspections before sending for an authorised
service technician.
Type of fault Corrective action
No arc. S Check that the mains power supply switch is turned on.
S Check that the welding current supply and return cables are
correctly connected.
S Check that the correct current value is set.
The welding current is
interrupted during welding.
S Check whether the overheating protection has operated (fault
code E6 is displayed on the control panel).
S Check the mains power supply fuses.
The overheating protection trips
frequently.
S Make sure that you are not exceeding the rated data for the
welding power source (i.e. that the unit is not being
overloaded).
Poor welding performance. S Check that the welding current supply and return cables are
correctly connected.
S Check that the correct current value is set.
S Check that the correct electrodes are being used.
S Check the mains power supply fuses.
GB
-- 2 0 --
bt30d1ea
9 ORDERING SPARE PARTS
Tig 3000i is designed and tested in accordance with the international and European
standards IEC/EN 60974--1, 60974--3 and EN 60974--10. It is the obligation of the service
unit which has carried out the service or repair work to make sure that the product still
conforms to the said standard.
Spare parts may be ordered through your nearest ESAB dealer, see the last page of
this publication.
GB
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
ESAB Tig 3000i Origo™ Tig 3000i Manuale utente
- Categoria
- Sistema di saldatura
- Tipo
- Manuale utente
- Questo manuale è adatto anche per
in altre lingue
Documenti correlati
-
ESAB Tig 3000i Origo™ Tig 3000i Manuale utente
-
ESAB Tig 3000i AC/DC Origo™ Tig 3000i AC/DC Manuale utente
-
ESAB Mig L3000i Origo™ Mig L3000i Manuale utente
-
ESAB Caddy Arc 151i Manuale utente
-
ESAB MechTig 3000i Aristo® MechTig 3000i Manuale utente
-
ESAB Mig U4000i Manuale utente
-
ESAB Mig U5000i Manuale utente
-
-
-
ESAB Aristo®Mig U400 Manuale utente