ABB DCS550 Series Quick Manual

DCS550

Quick Guide

DCS550 Drives (20 A to 1000 A)

2 3ADW000395R0100 DCS550 Quick guide edisf a2 3ADW000395R0100 DCS550 Quick guide edisf a

DCS550 Quick Guide

english Contents

DC Drives Worldwide Service Network .............................. 3

DCS550 Manuals ............................................................... 4

DCS550 DC Drives ............................................................. 5

Brief instructions for CD and documents overview ............. 7

Notes on EMC .................................................................... 8

Standard function assignments for the terminals ............... 10

Connection example ......................................................... 11

Fan power connection ...................................................... 13

Terminal locations on the converter ................................... 14

Notes For North American Installations ............................. 15

Safety and operating instructions .....................................17

Installing the DCS550 PC tools on Your computer ............ 18

Commissioning .................................................................19

DCS550 Control Panel ..................................................... 20

Dimensions, drilling patterns and weights ........................ 77

Fault / Alarm list ............................................................... 80

Diagnosis messages.......................................... ...............86

Macro & Firmware structure .............................................. 91

Declaration of conformity ................................................ 104

Declaration of Incorporation ........................................... 105

deutsch Inhalt

DC Drives Worldwide Service Network .............................. 3

DCS550 Manuals / DCS550 Handbücher ........................... 4

DCS550 Gleichstromantriebe ........................................... 21

Kurzanweisung CD und Dokumentationsübersicht .......... 23

EMV Filter ......................................................................... 24

Digitaler und analoger E-A/Anschluss von SDCS-CON-F .. 26

Anschlussbeispiel .............................................................27

Lüfterkühlung ...................................................................29

Klemmen- und Steckeranordnung des Stromrichters ........ 30

Sicherheits- und Anwendungshinweise ............................. 31

Installation der DCS550 Programme auf dem PC ............. 32

Inbetriebnahme ................................................................33

DCS550 Steuertafel .......................................................... 34

Abmessungen, Bohrbild und Gewichte ............................ 77

Fehler- / Alarmliste ...........................................................80

Diagnosemeldungen.......................................... ............... 86

Makro & Firmware Struktur ...............................................91

Declaration of conformity ................................................ 104

Declaration of Incorporation ........................................... 105

italiano Indice

DC Drives Worldwide Service Network .............................. 3

DCS550 Manuals / DCS550 Manuali .................................. 4

DCS550 DC Drives ........................................................... 35

Brevi istruzioni CD e documentazione Panoramica ........... 37

Note sulle EMC .................................................................38

Assegnazione funzioni standard per i morsetti .................. 40

Esempi schemi di collegamento........................................41

Ventole di raffreddamento ................................................. 43

Posizioni terminali sul convertitore .....................................44

Istruzioni per la sicurezza .................................................. 45

Installa i DCS550 PC tools sul Tuo computer ....................46

Messa in servizio .............................................................. 47

DCS550 Pannello di controllo ........................................... 48

Dimensioni, schemi di foratura e pesi ...............................77

Errore / Allarme di lista ..................................................... 80

Messaggi di diagnostica.......................................... ......... 86

Struttura macro & ﬁrmware ............................................... 91

Declaration of conformity ................................................ 104

Declaration of Incorporation ........................................... 105

español Contenido

DC Drives Worldwide Service Network ............................... 3

DCS550 Manuals / Manuales de DCS550 .......................... 4

Convertidores de CC DCS550 ......................................... 49

Instrucciones para el CD y de la documentación .............. 51

Notas acerca de EMC ..................................................... 52

Asignaciones de funciones estándar para los terminales ... 54

Ejemplo de conexión ........................................................ 55

Conexión de alimentación del ventilador .......................... 57

Ubicación de los terminales en el convertidor ................... 58

Instrucciones de seguridad ............................................... 59

Cómo instalar las herramientas para PC del DCS550 ......60

Puesta en funcionamiento ............................................... 61

Panel de control del DCS550 ........................................... 62

Dimensiones, patrones de taladrado y pesos....................77

Lista de errores / alarmas ................................................ 80

Mensajes de diagnóstico ................................................. 86

Estructura del macro & ﬁrmware ....................................... 91

Declaration of conformity ................................................ 104

Declaration of Incorporation ............................................ 105

français Sommaire

DC Drives Worldwide Service Network .............................. 3

DCS550 Manuals / Manuels du DCS550 ............................ 4

Variateurs à courant continu DCS550 ............................... 63

Documentation technique ................................................65

Compatibilité électromagnétique (CEM) ............................ 66

Raccordement standard des signaux d’E/S ...................... 68

Exemple de schéma de câblage ....................................... 69

Câblage du ventilateur ...................................................... 71

Emplacement des bornes sur le convertisseur .................. 72

Consignes de sécurité et d’exploitation............................. 73

Installation des outils logiciels du DCS550 sur votre PC ....74

Mise en service ................................................................. 75

Micro-console DCS550 .................................................... 76

Dimensions, perçages et poids ........................................77

Liste des erreurs / alarmes ............................................... 80

Messages de diagnostic.......................................... ......... 86

Structure du logiciel macro & système .............................. 91

Declaration of conformity ................................................ 104

Declaration of Incorporation ........................................... 105

33ADW000395R0100 DCS550 Quick guide edisf a 33ADW000395R0100 DCS550 Quick guide edisf a

english

ABB Drive Service EN

In order to offer the same after sales

service to our customer around the

world, ABB has created the DRIVE

SERVICE CONCEPT.

ABB's after sales service is globally

consistent due to common targets,

rules, and the way of operation. This

means for our customers:

Please visit the ABB drive service

homepage

www.abb.com/drivesservices

ABB Drive Service FR

Pour offrir la même qualité de service

à tous nos clients, ABB a créé DRIVE

SERVICE CONCEPT.

Dans le monde entier, les équipes de

service proposent les mêmes presta-

tions aux mêmes conditions avec les

mêmes objectifs.

Pour en savoir plus, connectez-vous

sur ABB drive service homepage

www.abb.com/drivesservices

ABB Drive Service DE

Um jedem Kunden rund um die Welt

die gleiche Service Dienstleistung an-

bieten zu können, hat ABB das DRIVE

SERVICE CONCEPT entwickelt.

Durch die Definition von einheitlichen

Zielen, Regeln, und Arbeitsvorschrif-

ten kann ABB die Dienstleitungs

Produkte weltweit auf gleichwertig

hohem Qualitätsniveau anbieten. Für

unsere Kunden bedeuted dies:

Bitte besuchen Sie die ABB-Home-

page Service für Antriebe

www.abb.com/drivesservices

ABB Drive Service IT

ABB ha creato il DRIVE SERVICE

CENCEPT, con lo scopo di offrire ai

nostri clienti lo stesso servizio post

vendita in tutto il mondo.

Attraverso la definizione di obbiettivi

comuni, ruoli e modo di operare, le

attività post vendita di ABB offrono

sevizi coerenti nella loro globalità. Per

i nostri clienti questo significa:

Vi invitiamo a visitare la homepage

ABB drive service

www.abb.com/drivesservices

ABB Drive Service ES

Para poder ofrecer el mismo servicio

posventa a nuestros clientes en todo

el mundo, ABB ha creado el CON-

CEPTO DE SERVICIO DE CONVER-

TIDORES.

El servicio posventa de ABB está

mundialmente consolidado gracias a

unos objetivos y normas comunes,

así como a su funcionamiento. Esto

significa para nuestros clientes:

Visiten el portal de convertidores de

ABB

www.abb.com/drivesservices

DC Drives Worldwide Service Network

Country Local ABB Service Town Service Phone No.

Argentina Asea Brown Boveri S.A. BUENOS AIRES +54 (0) 12 29 55 00

Australia ABB NOTTING HILL +61 (0) 3 85 44 00 00

Austria ABB AG WIEN +43 1 60 10 90

Belgium ABB N.V. ZAVENTEM

+32 27 18 64 86

+32 27 18 65 00 - 24h service

Brazil ABB Ltda. OSASCO +55 (0) 11 70 84 91 11

Canada ABB Inc. SAINT-LAURENT +1800 865 7628

China ABB China Ltd BEIJING +86 40 08 10 88 85 - 24h service

Czech Republic ABB S.R.O. PRAHA +42 02 34 32 23 60

Finland ABB Oy Service KUUSANKOSKI +35 8 10 22 51 00

Finland ABB Oy Product Service HELSINKI +35 8 10 22 20 00

Finland ABB Oy Service NOKIA +35 8 10 22 51 40

France

ABB Automation

ABB Process Industry

MONTLUEL from abroad

France

+33 1 34 40 25 81

+0810 02 00 00

Germany ABB Process Industries MANNHEIM +49 18 05 22 25 80

Greece ABB SA METAMORPHOSSIS +30 69 36 58 45 74

Ireland ABB Ireland Ltd. TALLAGHT +35 3 14 05 73 00

Italy ABB MILAN +39 02 90 34 73 91

Korea, Republic ABB Ltd., Korea CHONAN +82 (0) 4 15 29 22

Malaysia ABB Malaysia Sdn. Bhd. KUALA LUMPUR +60 3 56 28 42 65

Mexico ABB Sistemas S.A. DE C.V. TLALNEPANTLA +52 53 28 14 00

Netherlands ABB B.V. ROTTERDAM +31 1 04 07 88 66

New Zealand ABB Service ltd AUCKLAND +64 92 76 60 16

Poland ABB Centrum IT Sp.zo.o

WROCLAW

LODZ

+48 42 61 34 96 2

+48 42 29 93 91 39 5

Russia ABB Automation LLC MOSCOW +74 95 96 0

Switzerland ABB AG DÄTTWIL +41 5 85 86 87 86

Singapore ABB Industry Pte Ltd SINGAPORE +65 67 76 57 11

Slovakia ABB Elektro s.r.o. BANSKA BYSTRICA +42 19 05 58 12 78

South Africa ABB South Africa (Pty) Lt JOHANNESBURG +27 1 16 17 20 00

Spain ABB Automation Products BARCELONA +34 9 37 28 73 00

Taiwan ABB Ltd. TAIPEI 105 +88 62 25 77 60 90

Thailand ABB Limited SAMUTPRAKARN +66 27 09 33 46

Turkey ABB Elektirk Sanayi A.S ISTANBUL +90 2 16 36 52 90

USA ABB Industrial Products NEW BERLIN

+1 26 27 85 32 00

+1 262 435 7365

Venezuela ABB S.A. CRCS +58 (0) 22 38 24 11 / 12

4 3ADW000395R0100 DCS550 Quick guide edisf a4 3ADW000395R0100 DCS550 Quick guide edisf a

DCS550 Manuals

Language

Public. number E D I ES F CN RU

Quick Guide 3ADW000395 x x x x x

DCS550 Tools & Documentation CD 3ADW000377 x

DCS550 Modules

DCS550 Flyer 3ADW000374 x x

DCS550 Technical Catalog 3ADW000378 p

DCS550 Manual 3ADW000379 x

DCS550 Service Manual 3ADW000399 p

Installation according to EMC 3ADW000032 x

Technical Guide 3ADW000163 x

Extension Modules

RAIO-01 Analog IO Extension 3AFE64484567 x

RDIO-01 Digital IO Extension 3AFE64485733 x

Serial Communication

RPBA-01 PROFIBUS 3AFE64504215 x

RCAN-01 CANopen 3AFE64504231 x

RCNA-01 ControlNet 3AFE64506005 x

RDNA-01 DeviceNet 3AFE64504223 x

RMBA-01 MODBUS 3AFE64498851 x

RETA-01 Ethernet 3AFE64539736 x

x -> existing p -> planned

Status 05.2011

DCS550 Drive Manuals-List_d.doc

5

3ADW000395R0100 DCS550 Quick guide edisf a

53ADW000395R0100 DCS550 Quick guide edisf a

english

Standard Features

− compact

− highest power ability

− simple operation

− comfortable assistants, e.g. for autotuning or commissioning

6 3ADW000395R0100 DCS550 Quick guide edisf a6 3ADW000395R0100 DCS550 Quick guide edisf a

DCS550 DC Drives

Technical data

Mains supply volt. 230...525 V,

+/–10 %, 3~

Frequency 50...60 Hz, +/–5

Hz

Electronics supply 115...230 V,

–15 % / +10 %, 1~

DC Output current 20...1000 A

Overload capability 200 %

Ambient conditions

Ambient temperat. 0° ... +40° C

40° ... 50°C with

reduction

Storage temperat. –40° ... +55° C

Transport temper. –40° ... +70° C

Relative humidity 5 ... 95 %, not

condensing

(max. 50 % betw.

0°...5° C)

Pollution degree Class 2

Protection class IP 00

Altitude < 1,000 m height

above sea level:

nominal Current

> 1,000 m height

above sea level:

with reduction

I/O

Digital inputs: 8 standard, up to

14 optional

Digital outputs: 5 standard, up

to 9 optional

Analog inputs: 4 standard +/–

10 V; 0/2…10 V, up to 8 optional

+/ 20 mA; 0/4…20 mA

Analog outputs: 3 standard (1x

I

act

) +/-10 V; 0/2…10 V, up to 7

optional –20 mA; 0/4…20 mA

PC-Tools

DriveWindow Light: free of

charge with every converter,

Standard RS232 PC-connection

Communication

Serial communication

• Ethernet • Proﬁbus

• CANopen • DeviceNet

• ControlNet • EtherCat

• Modbus • ProﬁNet

Industrial IT

©

enabled

Protections

Speed feedback monitoring •

Temperature • Overload • Over

speed • Motor stalled • Motor

over current • Motor over voltage

• Field over current • Minimum

ﬁeld current • Zero speed •

Armature current ripple • Mains

over- and under voltage

Approvals

(in preparation 12/2011)

Adaptive Programming

pre-deﬁned drive-speciﬁc function

blocks, e.g.

• Free process controller (PI-

Controller)

• I/O- and digital Operations

With control panel or PC-Tool, no

need for additional hardware

Speed Feedback

EMF

Analog tacho

Encoder

Unit

size

2-Q

rated Current

DCS550-S01

4-Q

rated Current

DCS550-S02

Supply voltage

[V

AC

]

max. field

current

internal

Dimensions

I

DC

[A] I

DC

[A] 230 400 525 [A

DC

] h x w x d [mm] h x w x d [inch]

F1 20 25 12 370 x 270 x 208 14.56 x 10.65 x 8.20

45 50

65 75

90 100

F2 135 150 18 370 x 270 x 264 14.56 x 10.65 x 10.40

180 200

225 250

270 300

F3 315 350 25 459 x 270 x 310 18.07 x 10,65 x 12,25

405 450

470 520

F4 610 680 35 644 x 270 x 345 25.35 x 10.65 x 13.60

740 820

900 1000

Current ratings, dimensions

7

3ADW000395R0100 DCS550 Quick guide edisf a

73ADW000395R0100 DCS550 Quick guide edisf a

english

Brief instructions for CD and documents overview

We appreciate that you purchased an ABB DC drive power

converter and thank you for the trust you put in our products.

This brochure was put together to make sure that you con-

tinue to be satisfied with our product. It is intended to provide

you with a brief overview of the product's key data, EMC

notes, typical applications, start-up and trouble-shooting.

If you need more information about the product you are pro-

vided with a CD-ROM in addition to this brief documentation.

The CD-ROM is part of the delivery and features the following

contents:

Technical catalog (3ADW000378)

Comprehensive information to engineer complete DC drive

systems.

Manual (3ADW000379)

Detailed information, with all important particulars about the

individual components, like module dimensions, electronic

boards, fans and auxiliary components.

Information for mechanical and electrical installation are also

included.

Detailed information with all important issues about firmware

and setting of parameters. The manual includes information

for start-up and maintenance of the entire drive, in detailed

form.

This manual also includes Fault and Alarm codes and informa-

tion for trouble shooting.

Service Manual (3ADW000399)

for maintenance and repair of the converters.

Additional information about applications and technical

accessories (e.g. Hardware extension or Field bus interfaces)

are handled by separate manuals.

See table DCS550 manuals.

System requirements to use the CD-ROM

©

2

0

1

A

B

A

u

t

o

m

a

t

i

o

n

P

r

o

d

u

c

t

s

G

m

b

H

-

A

l

R

i

g

h

t

s

R

e

s

e

r

v

e

d

3ADW 000 377 R0201 / April 2011

System configuration

WINDOWS 98, NT, 2000, XP

Acrobat Reader 4.0 or higher

Internet Explorer 5.0 or higher

I

f

t

h

e

C

D

R

O

M

w

o

n

’

t

s

t

a

r

t

a

u

t

o

m

a

t

i

c

a

l

y

p

l

e

a

s

e

x

e

c

u

t

e

S

T

A

R

T

.

B

A

T

System confirmation

Win2000, WinXP

Before installation of PC tools

remove previous version by

CONTROL PANEL of your

PC

Read more details in

Quick Guide 3ADW000191

Content

This CD ROM provides

information about DCS550 and

contains PC tools:

DWL 2.93 for DC drives

+Commissioning Wizard 1.0

+DWL AP 2.2

FDT 2.2 Firmware

download kit

+ workspace

Firmware 1.1

DCS550

Ver.: 1.10

System confirmation

Win7, Win2000, WinXP

Before installation of PC tools

remove previous version by

CONTROL PANEL of your PC

− Operating system

WINDOWS 7, 2000, XP

− ACROBAT READER

In case the CD ROM does not

start automatically, please

double click on Setup.exe.

Further support

In addition we offer further support, since we can only be

satisfied when you, as our customer, are satisfied with us and

our products.

Internet

On the ABB homepage under

www.abb.com/dc

you'll find abundant information for

− DC products

− service support

− the latest updates

− tools

− downloads, etc.

Please don't hesitate to visit us.

Contacts

If you require any further information, please contact your

nearest ABB Drives office or send an email to:

DC-Drives@de.abb.com

Please give us your name, your company address and phone

number. We immediately put you in contact with our special-

ist.

8 3ADW000395R0100 DCS550 Quick guide edisf a8 3ADW000395R0100 DCS550 Quick guide edisf a

Not applicable

The paragraphs below describe selection

of the electrical components in conformity

with the EMC Guideline.

The aim of the EMC Guideline is, as the

name implies, to achieve electromagnetic

compatibility with other products and

systems. The guideline ensures that the

emissions from the product concerned

are so low that they do not impair another

product‘s interference immunity.

In the context of the EMC Guideline, two

aspects must be borne in mind:

– the product‘s interference immunity

– the product‘s actual emissions

The EMC Guideline expects EMC to be taken

into account when a product is being devel-

oped; however, EMC cannot be designed in, it

can only be quantitatively measured.

Note on EMC conformity

The conformity procedure is the responsibility

of both the power converter‘s supplier and the

manufacturer of the machine or system con-

cerned, in proportion to their share in expand-

ing the electrical equipment involved.

Notes on EMC

M

Mains filter

Converter

Line reactor

Supply transformer for a residential

area (rating normally

≤

1,2 MVA)

Earthed public 400-V

network with neutral

conductor

Medium-voltage network

Earthed

neutral

To other loads, e.g. drive systems

An isolating transformer

with an earthed screen

and earthed iron core

renders mains filter and

line reactor superfluous.

Operation at public

low-voltage network

together with other

loads of all kinds.

Residential area

To other loads which have to be protected from the system disturbances caused by

power converters (HF interference and commutation notches)

Converter

M

alternative

Line reactor +

Y-capacitor

Medium-voltage network

Supply transformer for a residential

area (rating normally

≤

1.2 MVA)

Earthed

neutral

Earthed public 400-V

network with neutral

conductor

To other loads, e.g. drive systems

Mains filter

Line reactor

Converter Converter

Mains filter

Line reactor

Converter Converter

An isolating transformer

with an earthed screen

and earthed iron core

renders mains filter and

line reactor superfluous.

Operation at public

low-voltage network

together with other

loads of all kinds.

To other loads, e.g. drive systems

To other loads which have to be protected from the system disturbances caused by

power converters (HF interference and commutation notches)

Earthed public 400-V

network with neutral

conductor

Operation at public

low-voltage network

together with other

loads of all kinds.

Light industry

Residential area

Commutaion notches < 20%

You will find further informa-

tion in publication:

Technical Guide chapter:

EMC Compliant Installation

and Configuration for a

Power Drive System

satisﬁed satisﬁed

Not applied, since category C1 (general distribution sales channel) excluded Not applicable

First environment (residential area with light industry) with PDS category C2 Second environment (industry) with PDS categories C3, C4

9

3ADW000395R0100 DCS550 Quick guide edisf a

93ADW000395R0100 DCS550 Quick guide edisf a

english

For compliance with the protection ob-

jectives of the German EMC Act (EMVG)

in systems and machines, the following

EMC standards must be satisfied:

Product Standard EN 61800-3

EMC standard for drive systems (Pow-

erDriveSystem), interference immunity

and emissions in residential areas,

enterprise zones with light industry and

in industrial facilities.

This standard must be complied with in

the EU for satisfying the EMC require-

ments for systems and machines!

Classification

The following overview

utilises the terminology and

indicates the action required

in accordance with Product

Standard EN 61800-3.

For the DCS550 series,

the limit values for emitted

interference are complied

with, provided the measure

indicated is carried out. PDS

of category C2 (formerly

restricted distribution in first

environment) is intended to

be installed and commis-

sioned only by a professional

(person or organization with

necessary skills in installing

and/or commissioning PDS

including their EMC aspects).

For power converters without

additional components, the

following warning applies:

This is a product of category

C2 under IEC 61800-3:2004.

In a domestic/residential

environment this product

may cause radio interference

in which case supplementary

mitigation measures my be

required.

The field supply is not depict-

ed in this overview diagram.

For the field current cables,

the same rules apply as for

the armature-circuit cables.

MMMM

emv_clssif_b.dsf

Converter

transformer

Case-referenced EMC analysis

alternative

Converter

transformer

with earthed

iron core

(and earthed

screen where

appropriate)

alternative

I > 400 A

and/or

U > 500 V

Operation with separate power converter transformer. If there

are other loads at the same secondary winding, these must be

able to cope with the commutation gaps caused by the power

converter. In some cases, commutating reactors will be

required.

To other loads, e.g. drive systems

Converter Converter

Line reactor

Medium-voltage network

Industrial

zone

Legend

Unscreened cable with restriction

Screened cable

For emitted interference, the following apply:

EN 61000-6-3 Specialised basic standard for emissions in light industry

can be satisfied with special features (mains ﬁlters,

screened power cables) in the lower rating range *(EN 50081-1).

EN 61000-6-4 Specialised basic standard for emissions in industry *(EN 50081-2)

For interference immunity, the following apply:

EN 61000-6-1 Specialised basic standard for interference immunity in

residential areas *(EN 50082-1)

EN 61000-6-2 Specialised basic standard for interference immunity in

industry. If this standard is satisfied, then the EN 61000-6-1

standard is automatically satisfied as well *(EN 50082-2)

* The generic standards are given in brackets

satisﬁed satisﬁed

on customer's request

satisﬁed

M

I

DC

< 100 A

I

DC

< 100 A

I

DC

>100 A

Supply transformer for a

residential area (rating

normally

≤

1.2 MVA)

Earthed 400-V network

with neutral conductor

;

3~

≤

400 A

Operation at low-voltage network together with

other loads of all kinds, apart from some kinds

of sensitive communication equipment.

To other loads, e.g. drive systems

Line reactor +

Y-capacitor

Line reactor

Converter Converter

Mains filter

Earthed

neutral

Medium-voltage network

Industrial zone

alternative

Line reactor

Converter

alternative

Commutation notches < 40%

PDS category C3

PDS category C4

EN 61800-3

Standards

EN 61000-6/3

EN 61000-6-2

EN 61000-6-1

satisﬁed satisﬁed

Not applied, since category C1 (general distribution sales channel) excluded Not applicable

First environment (residential area with light industry) with PDS category C2 Second environment (industry) with PDS categories C3, C4

10 3ADW000395R0100 DCS550 Quick guide edisf a10 3ADW000395R0100 DCS550 Quick guide edisf a

±90...

±

270 V

±

30...

±

90 V

±

8...

±

30 V

AI4

GND

Power

Sense 0 V

Sense 5 V

AI3

AI1

I-act

GND

+10V

GND

-10V

DI1

DI3

DI4

DO4

DO1

3

4

5

6

9

X4:1

3

4

10

4

1

2

3

6

5

10

8

9

10

5

2

6

8

10

8

X1:1

X2:1

X3:1

X5:

SDCS-CON-F

B22_001_0_a.dsf

+

-

S2

3

4

250

S3

3

4

250

ATACH

+

-

+

-

+

-

+

-

GND

10

+

-

+

-

+

-

5V

S4

11

12

24V

K1

X96:1

t

230V

E

SDCS-PIN-F

1

3

4

6

S1

1

3

S4

2

121

100nF

4

6

S4

5

121

100nF

7

S4

8

121

100nF

10k

9

ChA

ChB

ChZ

ChA

ChB

ChZ

Firmware

Resolution

[bit]

Input/output

values

Hardware

Scaling

by

Common

mode

range

Remarks

15 + sign ±90...270 V

±30...90 V

±8...30 V

①

Firmware

±15 V

15 + sign -10...0...+10 V Firmware ±15 V

15 + sign -10...0...+10 V Firmware ±15V

Power

+10 V ≤ 5 mA

for ext. use

e.g. refer. pot.

-10 V ≤ 5 mA

11 + sign -10...0...+10 V Firmware ≤ 5 mA

-10...0...+10 V Firmware+

Hardware

≤ 5 mA

8 V -> min. of

325% of [99.03] or

230% of [4.05]

Encoder supply Remarks

Inputs not isolated

Impedance = 120 W, if selected

max. frequency ≤ 300 kHz

5 V

24 V

≤ 250 mA

Sense lines for GND and supply

to correct voltage drops on cable

(only if 5 V encoder is in use).

Input value Signal

deﬁnition by

Remarks

0...7.3 V

7.5...50 V

Firmware

-> “0“ status

-> “1“ status

Output value Signal

deﬁnition by

Remarks

50 * mA

22 V at no

load

Firmware

Current limit for all 7

outputs = 160 mA

Do not apply any reverse

voltages!

* short circuit protected

① gain can be varied in 15 steps between 1 and 4 by software

parameter

Standard function assignments for the terminals

11

3ADW000395R0100 DCS550 Quick guide edisf a

113ADW000395R0100 DCS550 Quick guide edisf a

english

Converters F1...F4 drive configuration using ‘OnBoard‘ field exciter

Terminal selection according FACTORY macro (default)

F6

DCS550_ans_1_c.dsf

further information see the following page

Connection example

12 3ADW000395R0100 DCS550 Quick guide edisf a12 3ADW000395R0100 DCS550 Quick guide edisf a

START, STOP and E-STOP control

The relay logic can be split into three parts:

a: Generation of the ON/OFF and START/STOP command:

The commands represented by K20 and K21 (latching inter-

face relay) can be e.g. generated by a PLC and transferred to

the terminals of the converter either by relays, using galvanic

isolation or directly via 24V signals.

These commands can be as well transferred via serial com-

munication. Even a mixed solution can be realized by select-

ing different possibilities for the one or the other signal (see

parameter group 11).

gen_ctrl_cmd_c.dsf

b: Generation of control and monitoring signals:

The main contactor K1 for the armature circuit is controlled

by a dry contact (DO 8) located on the SDCS-PIN-F. Status

of fans and fans klixon can be monitored by means of fan ack

signals: MotFanAck (10.06).

c: OFF2, OFF3 Stop function:

Beside ON/OFF and START/STOP, the drive is equipped with

two additional stop functions, OFF2 and OFF3, according to

Profibus standard. OFF3 is a scalable stop function (ramp-

stop, max torque stop, dynamic braking …) to perform stop

category 1. This function should be connected to the E-STOP

button without any time delay. In case of ramp stop selection

the, K 15 timer relay must be set longer than the EStopRamp

(22.04). For COAST selection, the drive opens the main con-

tactor immediately.

OFF2 switches off DC current as fast as possible and pre-

pares the drive for opening main contactor or drop down

mains supply. For a normal DC motor load the time to switch

OFF the DC current is below 20 ms. This function should be

connected to all signals and safety functions opening the main

contactor. This function is important for 4-quadrant drives. Do

not open main contactor during regenerative current.

The correct sequence is

1. switch off regenerative current

2. then open the main contactor

In case of the E-STOP is hit, the information is transferred to

the converter via digital input 5. In case of rampstop, or max

torque selection the converter will decelerate the motor and

then open main contactor.

If the drive has not finished the function within the K15 timer

setting, the drive must get the command to switch OFF the

current via K16. After K16 timer set has elapsed the main

contactor is opened independent of the drives status.

Anschl_special_b.dsf

Timer K15

Timer K16

Stop-Mode_a.dsf

E-STOP

speed

Block current control

K1 main contactor

E-Stop ramp Coast

E-Stop reaction

13

3ADW000395R0100 DCS550 Quick guide edisf a

133ADW000395R0100 DCS550 Quick guide edisf a

english

Converter type Model Configuration Fan voltage

DCS550-S01-0020, ...,

DCS550-S02-0025

F1 - no fan, convection cooled

DCS550-S01-0045, ...,

DCS550-S02-0100

F1 1 1 x 3110KL-05W... (internal 24 V

DC

)

DCS550-S01-0135, ...,

DCS550-S02-0300

F2 2 2 x 4715MS (115 / 230 V

AC

)

DCS550-S01-0315, ...,

DCS550-S02-0450

F3 2 2 x 4715MS (115 / 230 V

AC

)

DCS550-S01-0470, ...,

DCS550-S02-0520

F3 3 2 x 4715MS (115 / 230 V

AC

)

2 x 3115FS (115 / 230 V

AC

)

DCS550-S01-0610, ...,

DCS550-S02-0820

F4 4 1 x W2E200 (230 V

AC

)

DCS550-S01-0900, ...,

DCS550-S02-1000

F4 4 1 x W2E250 (230 V

AC

)

Fan power connection

Fan assignment for DCS550

Fan connection for DCS550

1 2 3

X52:

4 5

L

N

230 V

AC

1 2 3

X52:

4 5

L

N

115 V

AC

M

~

1 2 3

X52:

M

~

4 5

M55 M56

M

~

1 2 3

X52:

M

~

4 5

M55 M56

M

~

M

~

M57 M58

M55

M

~

1 2 3 4 5

X52:

L

N

L

N

1 2 3

X52:

4 5

L

N

230 V

AC

1 2 3

X52:

4 5

L

N

115 V

AC

ϑ

only 230 V

AC

M55

M

~

X19:

SDCS-PIN-F

Configuration 4

F4

Configuration 3

F3

Configuration 2

F2, F3

Configuration 1

F1

Terminals are located on top of the converter housing

14 3ADW000395R0100 DCS550 Quick guide edisf a14 3ADW000395R0100 DCS550 Quick guide edisf a

Terminal locations on the converter

Macro ﬁnder

Macro name

Main

Contactor

ON / OFF

Start/Stop

DI function

Comment DI5 --> ESTOP

DI6 --> Reset

Standard

AC Static

Jog1 --> DI1

Jog2 --> DI2

Ext Fault --> DI 3

Ext Alarm --> DI4

Hardware I/O control x

2-wire DC cont. US

DC Static

Jog1 --> DI1

Jog2 --> DI2

Ext Fault --> DI 3

Main Cont Ack --> DI4

Hardware I/O control x

3-wire DC cont. US

DC Pulse

Fix speed1 --> DI1

Ext Fault --> DI 3

Main Cont Ack --> DI4

Hardware I/O control x

3-wire Standard

AC Pulse

Fix speed1 --> DI1

Ext Fault --> DI 3

Ext Alarm --> DI4

Hardware I/O control x

Torque limit

AC Static

Jog1 --> DI1

Jog2 --> DI2

Ext Fault --> DI 3

Ext Alarm --> DI4

Hardware I/O control

+ Torque limit

x

Manual / Const

AC Pulse

Jog1 --> DI1

Jog2 --> DI2

Direction --> DI 3

SpC - KP, KI --> DI4

Hardware I/O control

select gain

x

Hand / Auto

AC Static

Control select --> DI2

Reference select --> DI2

Direction select --> DI 3

Hardware I/O control

or ﬁeld bus control

x

Hand / Mot Pot

AC Pulse

Motor pot up --> DI1

Motor pot down --> DI2

Direction select --> DI 3

Reference select --> DI4

Hardware I/O control

Reference hardware or Motor

potentiometer

x

Motor Pot

AC Static

Direction select --> DI 1

Motor pot up --> DI2

Motor pot down --> DI3

Motor pot minimum --> DI4

Hardware I/O control

Reference Motor potentiometer

x

Torque Ctrl

AC Static

OFF2 (coast stop) --> DI1

Torque select --> DI2

Ext Fault --> DI 3

Hardware I/O control

Speed control or Torque

reference

x

Enabling a macro

Use the

[DCS550Wizard] 2. Macro as-

sistant of DriveWindow Light or

Parameter browser, either

through the control panel,

DriveWindow, or DriveWindow

Light.

Use the following parameters:

ApplMacro (99.08) =

Macro selection

Applrestore (99.07) =

YES = execute selection

MacroSel (8.10) =

double check

NOTE

Functions and inputs defined by

macro can be changed later on

without restrictions.

NOTE

Macro diagrams see page 91 ...

X2X1 X3 X4 X5

1 1 1 1 1

S5

15

6 9

S3

S2

S4

1

2

1

2

1

2

1

2

D2100

1

D2001

D2002

D1000

1 30

1

2

1

2

S1

1

42

1

2

3

10

11

12

1

82

1

42

1

2

3

7

8

9

DCS550 terminal alloc_c.dsf

1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8

15

3ADW000395R0100 DCS550 Quick guide edisf a

153ADW000395R0100 DCS550 Quick guide edisf a

english

Notes For North American Installations

1. EMC conformity is not usually required in North America.

In most cases, the section “Notes on EMC” can be bypassed.

In this manual, you will see references to DIN, EN and VDE

standards. These are European standards and, generally, do

not apply to North America. It is, however, the responsibility of

the user to determine which standards need to be followed.

2. If using a DC contactor, you must connect an auxiliary

contact to a digital input of your choice and set para. Main-

ContAck accordingly. Set the following parameters:

MainContAck (10.21) = DI-1 (or any input you

choose for the DC cont.

auxiliary contact)

DO8BitNo (14.16) = 10

MainContCtrlMode (21.16)= DCcontact (3)

Set these parameters AFTER macros are loaded but BEFORE

the drive is commissioned.

Digital output 8 (DO-8) must be used to turn the DC con-

tactor on and off.

3. If using Dynamic Braking, the drive allows you to select

the stopping method under three different situations. Param-

eters 21.02, 21.03 and 21.04 select the stopping method for

loss of the OnOff, run command (StartStop, Jog1, Jog2, etc.),

and E-Stop input, respectively.

Each can be set to:

• RampStop • TorqueLimit

• CoastStop • DynBraking

In order to command the drive to perform a DB stop, one or

more of these parameters must be set to DynBraking. Most

users will want the drive to ramp stop when OnOff or a run

command (StartStop, Jog1, Jog2, etc.) input is cleared, and

dynamically brake when the E-Stop input is cleared. In that

case, use the following settings:

• Off1Mode (21.02) = RampStop

• StopMode (21.03) = RampStop

• E StopMode (21.04) = DynBraking

However, any case is allowed and the final decision is left to

the user.

Other parameters control stops during faults.

See:

LocalLossCtrl (30.27) ComLossCtrl (30.28)

FaultStopMode (30.30) SpeedFbFltMode (30.36)

If using EMF feedback with dynamic braking, set:

• DynBrakeDly (50.11) = t

Where: t = the time (sec) it normally takes the motor to

stop during dynamic braking

DC contactor US:

DC contactor US K1.1 is a special designed contactor with 2x

NO contacts for C1 and D1 connection and 1x NC contact for

connection of Dynamic Brake resistor RB.

The contactor should be controlled by signal 6.03 Bit 10.

The acknowledge can be connected to parameter:

10.21 MainContAck

10.23 DCBreakAck

DC Output Fuses: Fuses between the motor and the con-

verter are required for all regenerative (4-Q) converters.

This is to protect the motor and converter if a commutation

fault should occur. NOTE: DC output fuses are the same type

and size as AC line fuses.

Line reactor:

All thyristor-based dc converters cause notching in the AC

line due to motor commutation. A properly sized line reactor

will mitigate the effect on the line. Unless the converter uses

a dedicated isolation transformer, each converter requires its

own line reactor.

AC or DC contactor:

A contactor is required to safely disconnect the motor from

the incoming power when the converter is off. The contac-

tor can be installed between the line and the converter (an

AC contactor) or between the converter and the motor (a DC

contactor). Do not use both.

IMPORTANT: Other equipment may be necessary de-

pending on application and local codes.

Overview of the Installation and Commissioning Process

Step 1:

Check converter for damage. Contact ABB Technical Support

if damage is found. In North America, call 1-800-435-7365

(1-800-HELP-365)

Step 2:

Select supporting hardware for the converter:

For specific recommendations for fuses, reactors, and con-

tactors, see the DCS550 Manual or technical catalog.

Circuit breaker or disconnect:

Current rating = I

DC

* 0.816 * 1.25 (min)

= I

DC

* 0.816 * 2.50 (max)

Where: I

DC

= nominal DC motor current

Fuses:

AC Line Fuses: To properly protect the converter, semi-

conductor fuses on the incoming AC power line are required

in all cases.

16 3ADW000395R0100 DCS550 Quick guide edisf a16 3ADW000395R0100 DCS550 Quick guide edisf a

Step 3:

Mount and wire the converter and supporting hardware inside

an industrial enclosure with adequate cooling (DCS550 mod-

ules have rating of NEMA type OPEN).

The following control and signal wiring is required:

− If using an AC contactor, we recommend wiring an auxiliary

contact to the digital input you have designated as Main-

ContAck (10.21) or Start/Stop (10.16).

− If using a DC contactor, you must wire an auxiliary contact

from the contactor to the digital input you have designated

as MainContAck (10.21).

− Wire 115 or 230 V

AC

1-phase power to terminal block 99 for

converter control power.

− Wire 1-phase power to converter for cooling fans. See

table and wiring diagrams in this manual.

• F1 – F3 frames: 115/230 V

AC

selectable.

Fan terminal X52 is on top of the converter.

• F4 frame: use 230 V

AC

.

Fan terminal X52 is on top of the converter.

− Wire tachometer or encoder to terminal block X1 (tacho) or

X3 (encoder).

− Wire analog inputs (e.g., speed reference) and outputs

(e.g., meters for motor voltage, current) to terminal block

X1 and/or X2.

− Wire high speed serial interface if needed. (Requires op-

tional fieldbus interface board.)

− The DCS550 allows you to choose the usage of each digi-

tal and analog input and output. The converter has factory

default settings which can be changed by loading a macro,

but some designations are universal. They include:

• Digital input 5: Estop

• Digital input 6: Fault reset

• Digital input 7: On/Off (maintained) or On-Start

(pulsed)

• *Digital input 8: Start/Stop (maintained) or

Off-Stop (pulsed)

• Digital output 8: Main Contactor On

(3 Amps max. at 115 – 230 V

AC

)

*except Hand/Auto macro

− Other signals may be required depending on your applica-

tion (e.g., motor fan acknowledge input, Off2 input, fan-on

output, brake output).

− You will select the macro and / or choose the configuration

for digital and analog inputs and outputs in step 2 of the

commissioning process, or by updating group 10 and 14

parameters.

− Check all wire terminations (with continuity tester) before

proceeding to the next step.

Step 4:

Connect the drive system to incoming power and the motor to

the converter (both field and armature) as well as accessory

equipment (motor fan, thermal switch, brake, etc.).

− See hardware manual for typical cable size and tightening

torque recommendations.

− IMPORTANT: Be sure all safety equipment is properly

sized for your application

Step 5:

Apply control power to the converter.

− IMPORTANT: See section “Safety and Operating In-

structions” in this manual before proceeding.

− Apply power to terminal block 99 and X52. The keypad

should light up and show the menu screen. The converter

fans should start to run (if converter has fans).

Step 6:

Commission the converter using DriveWindow Light

(preferred) or the control panel.

− IMPORTANT: See safety alerts and general instructions

in the section “Commissioning” before proceeding.

− Install the DCS550 PC tools on your computer. Instruc-

tions are in this manual. Use DriveWindow Light to com-

mission your converter.

− If no PC is available, commission your drive using the con-

trol panel as follows:

• On the control panel, press the softkey to select

MENU.

• Using the down arrow, select ASSISTANTS.

Then press ENTER.

• Starting with “name plate data,” press SEL.

Change the value with the arrow keys.

Then press SAVE.

• Repeat above with other parameters.

Follow directions on the screen.

Configuring and Displaying analog and digital I/O

HINT: To see if the drive is responding to an “on” or “run” command, view signal 8.08.

Control Panel:

− Digital Status: View signal 8.05 (DI’s) or 8.06 (DO’s). Dis-

play is in hexadecimal.

− Configure digital inputs with Group 10.

− Analog Status: View signal 5.03 (AI1) or 5.11 (AO1). Dis-

play is in Volts.

− Configure analog speed ref. with Group 11.

DriveWindow Light:

− Connect to the DCS550 and go on line by clicking on File,

then New Online Drive.

− Click on Wizard, at left side of the screen.

− Click on Advanced.

− Check the box for “I/O assistant,” then click on Next.

− Click on “edit parameters” in the appropriate section (ana-

log or digital inputs or outputs).

17

3ADW000395R0100 DCS550 Quick guide edisf a

173ADW000395R0100 DCS550 Quick guide edisf a

english

1. General

In operation, drive converters, depending on their degree of

protection, may have live, uninsulated, and possibly also mov-

ing or rotating parts, as well as hot surfaces.

In case of inadmissible removal of the required covers, of

improper use, wrong installation or maloperation, there is the

danger of serious personal injury and damage to property.

For further information, see documentation.

All operations serving transport, installation and commission-

ing as well as maintenance are to be carried out by skilled

technical personnel (Observe IEC 364 or CENELEC HD 384

or DIN VDE 0100 and IEC 664 or DIN/VDE 0110 and national

accident prevention rules!).

For the purposes of these basic safety instructions, “skilled

technical personnel” means persons who are familiar with the

installation, mounting, commissioning and operation of the

product and have the qualifications needed for the perfor-

mance of their functions.

2. Intended use

Drive converters are components designed for inclusion in

electrical installations or machinery and are to be mounted in

a cubicle or finger protected area.

In case of installation in machinery, commissioning of the drive

converter (i.e. the starting of normal operation) is prohibited

until the machinery has been proved to conform to the provi-

sions of the directive 89/392/EEC (Machinery Safety Directive

- MSD). Account is to be taken of EN 60204.

Commissioning (i.e. the starting of normal opertion) is admis-

sible only where conformity with the EMC directive (89/336/

EEC) has been established.

The drive converters meet the requirements of the low-voltage

directive 73/23/EEC. They are subject to the harmonized

standards of the series prEN 50178/DIN VDE 0160 in con-

junction with EN 60439-1/ VDE 0660, part 500, and EN

60146/ VDE 0558.

The technical data as well as information concerning the sup-

ply conditions shall be taken from the rating plate and from

the documentation and shall be strictly observed.

3. Transport, storage

The instructions for transport, storage and proper use shall be

complied with.

The climatic conditions shall be in conformity with prEN 50178.

4. Installation

The installation and cooling of the appliances shall be in ac-

cordance with the specifications in the pertinent documenta-

tion.

The drive converters shall be protected against excessive

strains. In particular, no components must be bent or isolating

distances altered in the course of transportation or handling.

No contact shall be made with electronic components and

contacts.

Drive converters contain electrostatic sensitive components

which are liable to damage through improper use. Electric

components must not be mechanically damaged or destroyed

(potential health risks).

5. Electrical connection

When working on live drive converters, the applicable national

accident prevention rules (e.g. VBG 4) must be complied with.

The electrical installation shall be carried out in accordance

with the relevant requirements (e.g. cross-sectional areas of

conductors, fusing, PE connection). For further information,

see documentation.

Instructions for the installation in accordance with EMC

requirements, like screening, earthing, location of filters and

wiring, are contained in the drive converter documentation.

They must always be complied with, also for drive converters

bearing a CE marking. Observance of the limit values required

by EMC law is the responsibility of the manufacturer of the

installation or machine.

6. Operation

Installations which include drive converters shall be equipped

with additional control and protective devices in accordance

with the relevant applicable safety requirements, e.g. Act

respecting technical equipment, accident prevention rules etc.

Changes to the drive converters by means of the operating

software are admissible.

After disconnection of the drive converter from the voltage

supply, live appliance parts and power terminals must not be

touched immediately because of possibly energized capaci-

tors. In this respect, the corresponding signs and markings on

the drive converter must be respected.

During operation, all covers and doors shall be kept closed.

7. Maintenance and servicing

The manufacturer’s documentation shall be followed.

Keep safety instructions in a safe place!

Safety and operating instructions

for drive converters DCS / DCF / DCR

(in conformity with the low-voltage directive 73/23/EEC)

18 3ADW000395R0100 DCS550 Quick guide edisf a18 3ADW000395R0100 DCS550 Quick guide edisf a

After inserting the DCS550 CD all programs and documenta-

tion necessary to work with the DCS550 will be automatically

installed.

This includes:

1. DriveWindow Light for parameterization, commissioning

and service

2. Hitachi FDT 2.2 for firmware download

3. Installation CD of DCS550 Drive for e.g. DWL Wizard,

ABB documents

Attention:

If You do not want to install a certain program just skip it by

using Cancel at the beginning of the program’s wizard.

If the installation routine does not start automatically:

− Go to Start/Run and browse for setup.exe on the CD.

Now start the installation by confirming with OK

− Compact installation for DriveWindow Light + DCS550

add ons is reccomended

Steps to connect Drive to PC

− The documentation can be found under

C:\ABB\DCS550\Docu

− Remove design cover from the converter module

− Start DriveWindow Light PC tool

− Check the communication setting of your COM port

If You use ExpressCard to COM port interface or PCMCIA /

COM port double check the active COM enabled

Start => Settings => Control Panel => System => Hardware

=> Device Manager

− COM address of USB interface can change after the next

boot procedure or after disconnecting and reconnecting of

the USB interface.

Note:

ExpressCard / PCMCIA to COM port provide a stable and

faster drive interface.

Utilize DriveWindow Light or DCS550 Panel Wizard continue

with chapter Commissioning in this manual.

Installing the DCS550 PC tools on Your computer

Connect drive (X34) to your

PC COM port

Remove the DCS550 Control Panel

if present. Depress the locks to

remove the cover

19

3ADW000395R0100 DCS550 Quick guide edisf a

193ADW000395R0100 DCS550 Quick guide edisf a

english

Start the wizard in

DriveWindow Light

Commissioning

Danger! High voltage: this symbol warns of high

voltages which may result in injuries to persons

and/or damage to equipment. Where appropriate,

the text printed adjacent to this symbol describes

how risk of this kind may be avoided

General warning: this symbol warns of non-elec-

trical risks and dangers which may result in

serious or even fatal injuries to persons and/or

damage to equipment. Where appropriate, the text

printed adjacent to this symbol describes how risk

of this kind may be avoided.

Warning of electrostatic discharge: this symbol

warns you against electrostatic discharges which

may damage to unit. Where appropriate, the text

printed adjacent to this symbol describes how risk

of this kind may be avoided.

NEC motor overload protection

The DCS550 provides a solid-state motor overload protection

in accordance with the NEC. The overload protection (e.g.

protection level in percent of full-load motor current) can be

adjusted by parameters in group 31 and group 99

The instructions can be found in chapter Motor thermal model

of the DCS550 Manual.

General instructions

− This short commissioning refers to chapter Connection

examples of this publication.

− Safety and operating instructions - chapter of this publica-

tion.

− Recommendations for motor and field voltages see Techni-

cal catalog.

− In accordance with DIN 57 100 Part 727 / VDE 0100 Part

727, precautions must be taken to enable the drive to be

shut down, e.g. in the event of danger. The unit’s digital

inputs or the control panel are not sufficient as the sole

measure for this purpose!

Preparations

− Check unit for any damage!

− Install unit and wire it up

− Supply voltage level / Rated value correct for electronics

and fan?

− Supply voltage level / Rated value correct for armature-

circuit converter?

− Supply voltage level / Rated value correct for field supply?

− Wiring / cross-sections, etc. correct?

− EMERGENCY STOP functioning properly?

− COAST STOP functioning properly?

For basic commissioning press the Start button or select a specific assistant:

7. Field weakening assistant

6. Autotuning speed controller

5. Speed feedback assistant

4. Autotuning armature current controller

3. Autotuning field current controller

2. Macro assistant

1. Name plate data

Select specific

assistant & press Next

7. Field weakening assistant

6. Autotuning speed controller

5. Speed feedback assistant

4. Autotuning armature current controller

3. Autotuning field current controller

2. Macro assistant

1. Name plate data

Select specific

assistant & press Next

For more information about the wizard, parameters faults and alarms press the Help button!

Commissioning DriveWindow Light

20 3ADW000395R0100 DCS550 Quick guide edisf a20 3ADW000395R0100 DCS550 Quick guide edisf a

DCS550 Control Panel

The following table summarizes the button functions and displays of the DCS550 Control Panel

DCS800 QG pan ov_c.dsf

Parameters entered by assistant

99.02 Motor 1 nominal Voltage

99.03 Motor 1 nominal current

99.04 Motor 1 base speed

20.01 Motor 1 minimum speed

20.02 Motor 1 maximum speed

99.11 Motor 1 nominal field current

30.09 Armature over current level

30.16 Motor 1 over speed

99.10 Nominal mains voltage

99.12 Motor 1 used fex type

20.05 Torque maximum

20.06 Torque minimum

20.12 Motor 1 current limit bridge 1

20.13 Motor 1 current limit bridge 2

50.04 Motor 1 encoder pulse number, if selected

50.02 Motor 1 encoder measured mode, if selected

50.13 Motor 1 tacho volt, only DWL

50.12 Motor 1 tacho adapt, only DWL

20.03 Zero speed limit

22.01 Acceleration time 1

22.02 Deceleration time 1

30.12 Motor 1 field minimum trip

44.01 Field control mode

General display features

Following modes are available in the MAIN MENU:

1. Parameters mode

2. Start-up assistants mode

a. Name plate data

b. Macro assistant

c. Autotuning ﬁeld current controller

d. Autotuning armature current controller

e. Speed feedback assistant

(Tacho ﬁne tuning not available)

f. Autotuning speed controller

g. Field weakening assistant

(only used when maximum speed is higher than base

speed)

3. Macros mode (currently not used)

4. Changed parameters mode (compare to default and

display changed parameters)

5. Fault logger mode (Display fault history)

6. Clock set mode

7. Parameter backup mode

• copy active parameter set from the drive into the

DCS550 Control Panel (only in local mode)

• copy parameter set from DCS550 Control Panel into

the drive (only in local mode)

8. I/O settings mode (currently not used)

With USISel (16.09) it is possible to limit the amount of displayed parameters!

La pagina sta caricando ...

ABB DCS550 Series Quick Manual

Questo manuale è adatto anche per

ABB DCS550 Series Quick Manual

in altre lingue

Documenti correlati

Altri documenti