NuTone ECLIPSE 2730 Manuale utente

Marca: NuTone

Modello: ECLIPSE 2730

Categoria: Aeratori / essiccatori

Tipo: Manuale utente

MODELS 2730 & 2736 ECLIPSE

DOWNDRAFT BLOWER SYSTEM

READ AND SAVE THESE INSTRUCTIONS

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer.

If you have questions, contact the manufacturer at the address

or telephone number in the warranty.

2. Before servicing or cleaning unit, switch power off at service

panel and lock the service disconnecting means to prevent

power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a

qualified person(s) in accordance with all applicable codes

and standards, including fire-rated construction codes and

standards.

4. Sufficient air is needed for proper combustion and exhausting

of gases through the flue (chimney) of fuel burning equipment

to prevent backdrafting. Follow the heating equipment

manufacturer’s guideline and safety standards such as those

published by the National Fire Protection Association (NFPA),

and the American Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE), and the local code au-

thorities.

5. When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

6. Do not use this range hood with an additional speed control

device.

7. Ducted fans must always be vented to the outdoors.

8. To reduce the risk of fire, use only metal ductwork.

9. Do not install this product with the activating switch directly

behind a burner or element. Minimum distance between the

switch and the edge of the burner should be 4 inches.

10.Loose-fitting or hanging clothing should never be worn when

operating this appliance. They may be ignited by burners/

elements on cooktop.

11.Children should not be left alone or unattended in the area

where this appliance is in use.

12.When flaming foods, turn the blower OFF. An operating

blower may spread the flames.

13. This unit must be grounded.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

1. Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may

ignite. Heat oils slowly on low or medium settings.

2. Always turn hood ON when cooking at high heat or when

cooking flaming foods.

3. Clean ventilating fans frequently. Grease should not be

allowed to accumulate on fan or filter.

4. Use proper pan size. Always use cookware appropriate for

the size of the surface element.

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE

EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE

FOLLOWING

WARNING

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet,

or metal tray, then turn off the burner. BE CAREFUL TO

PREVENT BURNS. If the flames do not go out immedi

ately, EVACUATE AND CALL THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN - You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels

- a violent steam explosion will result.

4. Use an extinguisher ONLY if:

A. You know you have a Class ABC extinguisher, and you

already know how to operate it.

B. The fire is small and contained in the area where it

started.

C. The fire department is being called.

D. You can fight the fire with your back to an exit.

Based on “Kitchen Firesafety Tips” published by NFPA.

CAUTION

1. For general ventilating use only. Do not use to exhaust

hazardous or explosive materials and vapors.

2. To avoid motor bearing damage and noisy and/or unbalanced

impellers, keep drywall spray, construction dust, etc. off

power unit.

3. Clean filters and grease-laden surfaces frequently.

4. Do not repair or replace any part of this appliance unless

specifically recommended in this manual. All other servicing

should be done by a qualified technician.

5. Please read specification label on product for further informa-

tion and requirements.

PLANNING

INSTALLER: Save this manual for Electrical Inspector and Homeowner to use.

HOMEOWNER: Use and Care Information on Page 5.

AIR

VENT

COUNTER

TOP

BLOWER

BOX

CHIMNEY TOP

3-1/4" X 10"

DUCT CONNECTOR

COOK TOP

GEAR

MOTOR

COVER

TYPICAL INSTALLATION

120 VAC

GROUNDED

OUTLET

This downdraft blower system is

designed to be used to exhaust

airborne contaminants when cook-

ing with a variety of gas or electric

cooktops. It can be mounted in

island, peninsula, or conventional

wall locations.

This unit can be easily installed

following these basic steps:

•

Cut out the countertop

opening.

•

Mount the unit in the

cabinet.

•

Connect the ductwork

and electrical.

•

Install the cooktop.

PLANNING - (continued)

RIGHT

DISCHARGE

DOWN

DISCHARGE

(as shipped)

LEFT

DISCHARGE

EQUALS 6 FT. OF

STRAIGHT DUCT

6" ROUND

ELBOW

3-1/4" X 10"

TO 6" RD.

TRANSITION

3-1/4" X 10"

ELBOW

EQUALS 8

FT. OF

STRAIGHT DUCT

EQUALS 2

FT. OF

STRAIGHT DUCT

Pay special attention to the areas of potential interference

highlighted above. A countertop with (A) a raised lip and/or (B) a

backsplash may not allow enough flat countertop for a proper

installation. Note that 2" of flat countertop is required behind

cooktop and that 1-3/4" is necessary between the back edge of

the cooktop and the inside of cabinet back.

SPECIFICATIONS

VOLTS AMPS CFM DUCT

120 4.0 500 3-1/4 X 10

TAKE MEASUREMENTS

1. Refer to the cooktop installation instructions for dimensions of

cooktop, countertop cut-out, and cabinet requirements. The

Model 2730 will fit in most 30" wide cabinets and the Model

2736 will fit in most 36" wide cabinets. However, it is recom-

mended that oversized cabinets be used for easier installation.

2. Cooktop depth can vary greatly from one to another. This may

cause the fit of these two appliances to be rather tight.

Note: The high level of air flow of this appliance may affect the gas

flame on some types of gas cooktops. This is NORMAL and will

cause no harm, but can be corrected by lowering the speed of the

blower.

PLAN THE DUCTWORK

1. This downdraft blower system is designed for use with 3-1/4"

x 10" ductwork (can be transitioned to 6" round). Three

different discharge directions are available with side-to-side

adjustment for accurate alignment of ductwork.

2. For best performance: Choose the ducting option which

allows the shortest length of ductwork and a minimum

number of elbows and transitions. Check location of floor

joists, wall studs, electrical wiring or plumbing for possible

interference. NOTE: The unit is shipped with the 3-1/4" x 10"

discharge facing DOWN. See “CHANGING BLOWER DI-

RECTION” on page 3, if necessary.

3. The system will operate most efficiently when the ductwork

does not exceed 40 feet of equivalent duct. The chart, above,

shows equivalent feet of elbows and transitions. The number

of feet of straight duct plus the equivalent feet of transitions

and/or elbows to be used should equal 40 feet or less.

NOTE: The equivalent feet of various roof and wall caps has

been taken into consideration. Do not include them in this

calculation.

PLAN THE WIRING

1. The downdraft blower system draws 4 AMPS and requires a

120 VAC, 60 Hz circuit.

2. The unit has a 2 ft. long power cord with a 3-pronged plug.

Plan to provide a grounded outlet in a location which will allow

the unit’s power cord to reach. (Note: If the Model 2730 is

being installed in a 30" wide cabinet or the Model 2736 is being

installed in a 36" wide cabinet, the outlet cannot be located on

the back wall of cabinet.) Outlet may also be wall-mounted,

with access hole in cabinet.

LEVELING BRACKET -

FLANGE FACING IN

LEVELING BRACKET -

FLANGE FACING OUT

MOUNTING SCREWS

COVER PLATE

CLAMP

CHANNEL

NUT

BLOWER

MOTOR

PLUG

SHEET

METAL

SCREW

CLAMP

CHANNEL

NUTS

SHEET

METAL

SCREW

BOTTOM

FLANGE

BLOWER

PREPARATION

CHANGING BLOWER DISCHARGE (Optional)

The blower is shipped with its discharge facing DOWN. Follow

these steps ONLY if:

•

the position of the blower discharge needs to be moved

so ductwork does not interfere with floor joists, plumb

ing or wiring below.

•

it is necessary to rotate the blower discharge to the

RIGHT or LEFT.

Place the unit on its back on a table or work surface.

DOWN DISCHARGE - MOVING BLOWER LEFT OR RIGHT

Loosen

the 4 nuts and 2 clamp channels.

2. Slide blower to desired position.

3. Use supplied cover plate to close open space (if any).

4. Tighten wing nuts to secure top of blower and use sheet metal

screws through bottom flange to secure bottom of blower.

Remove

the 4 nuts and 2 clamp channels.

2. Carefully lift blower and disconnect motor plug if necessary.

Reposition blower and RECONNECT MOTOR PLUG.

3. Use supplied cover plate to close open space (if any).

4. Replace clamp channels and use nuts to secure the blower

in its new position.

5. Use sheet metal screws through bottom flange to secure

bottom of blower.

CUT COUNTERTOP OPENING

1. Lay out and cut the cooktop cut-out far enough FORWARD

so downdraft will fit behind it.

2. Set cooktop in place and slide it as far forward as possible.

Center and square it with edges of countertop.

3. Place the plastic template against the back flange of the

cooktop and center it. Trace around template to mark the

downdraft opening.

4. Remove cooktop from countertop.

5. Cut downdraft opening. Be careful not to chip edges of

countertop.

MOUNT THE UNIT

1. Set downdraft into opening. Extend leveling brackets to floor

of cabinet so downdraft sits straight. (Note: Leveling brackets

can be removed and re-attached in other positions. Bottom

flange may have to face inward in tight cabinet installations.)

2. Secure the downdraft to the countertop as follows: Hold the

downdraft against the back of countertop cut-out and tighten-

ing the 2 mounting screws (one on each end of unit) on

underside of countertop. Use a wood shim between screw

and underside of granite countertops.

3. Screw leveling brackets to bottom of cabinet. Tighten screws

holding leveling bracket to unit on each side.

LEFT OR RIGHT DISCHARGE

6" RD.

ELBOW &

DUCT-

WORK

3-1/4" X 10"

TO 6" RD.

TRANSITION

ç BLOWER è

COLLAR

SCREWS

SWITCH

COVER

SCREWS

SWITCH

MEMBRANE

SWITCH

BRACKET

INSTALL DUCTWORK

CAUTION -

BEFORE CUTTING HOLE IN CABINET FOR DUCT-

WORK:

Check for interference with floor joists, wall studs,

electrical wiring or plumbing.

1. Cut hole in cabinet as well as holes in wall or floor as

necessary.

2. Mount the roof or wall cap and work back towards the cabinet,

attaching all ductwork, elbows and transitions as previously

planned. Tape all ductwork connections to make them secure

and air tight.

3. Connect ductwork (and transition, if required) to downdraft. If

necessary, LOOSEN nuts and screws that hold the blower in

place, and slide blower left or right to meet ductwork. Re-

tighten screws and nuts.

Note: A 3-1/4" x 10" collar is provided for installers who prefer to

rivet the ductwork to the unit. This will allow blower to be removed

and replaced easily in service situations without disturbing

ductwork.

INSTALL ELECTRICAL WIRING

1. Mount a standard wiring box, with 3-pronged receptacle,

inside the cabinet. Make sure the downdraft’s power cord can

easily reach it.

2. Run appropriate power cable into cabinet and connect it to

receptacle.

3. Plug the downdraft’s power cord into the outlet.

WIRING DIAGRAM

INSTALL COOKTOP

1. Align the cooktop with the downdraft and fasten cooktop in

place.

Note: Accurate alignment of cooktop and downdraft is necessary

to ensure that there is no interference when air vent is raised and

lowered. There should be a gap of 1/32"-1/16" between the back

of the cooktop and the front of the downdraft cover.

ADJUSTMENT

The downdraft is factory-adjusted for proper operation. How-

ever, shipping and handling may affect the position of the

activating switch.

To adjust position of activating switch:

WARNING: To avoid possible electrical

shock, personal injury or death -

Disconnect electrical power.

1. If downdraft is plugged into electrical outlet, unplug it.

2. Lift air vent straight up and cock it slightly so it remains in the

UP position.

3. Remove switch cover from right end of air vent.

4. Loosen the 2 screws holding the switch bracket in place.

Position switch bracket so that activating switch just comes in

contact with underside of switch membrane. Tighten screws.

5. Replace switch cover, gently lower air vent into chimney, and

plug in power cord. Re-connect electrical power and check

operation.

USE AND CARE - (Continued)

KNOB

CLEANING

SERVICING

USE AND CARE

Always turn the downdraft blower on before you begin cooking to

establish an air flow in the kitchen. Let the blower run for a few

minutes to clean the air after you turn the cooktop off. This will

keep the whole kitchen cleaner and brighter.

CONTROLS

Turn the downdraft blower ON by pressing down on the activating

switch. The air vent will rise.

The blower can be turned ON or OFF and its speed can be

adjusted with the recessed knob on the right side of the air vent.

Turn the downdraft blower OFF by pressing the activating switch

again. The air vent will go down and the blower will shut OFF.

Note: For most convenient operation, set the blower to your

favorite speed. The blower will come on to this speed whenever

the activating switch is pressed and the air vent rises.

WARNING: Always disconnect electric

power supply before cleaning unit.

Use a mild detergent suitable for painted surfaces. DO NOT USE

ABRASIVE CLOTH, STEEL WOOL PADS, OR SCOURING

POWDERS. Vacuum blower to clean. Do not immerse blower in

water.

Wash the 2 aluminum grease filters in a mild detergent solution

or a dishwasher. Remove them from the air vent by grasping the

tab at the top of each filter.

Note: The filters are different sizes. Be sure to replace them as

removed, (wider one on the left), with tabs UP.

WARNING: Always disconnect electric

power supply before servicing unit.

It may be necessary to remove the downdraft blower system

from the cabinet in order to service components such as the

blower motor or air vent mechanism.

Disconnect power to the cooktop and remove it first. Reverse the

steps under “MOUNT THE UNIT” to remove the downdraft from

the cabinet.

Service parts are available from your local Broan distributor or

from the Broan Service Department, P.O. Box 140, Hartford, WI

53027 Phone: 1-800-637-1453.

SERVICE PARTS

Models 2730 & 2736

Downdraft Blower Systems

OPTIONAL DOOR KITS

*Standard Hardware - May be purchased locally.

**Service Assembly - Contains numerous parts.

MODEL NO. DESCRIPTION

273001C 30" White

273002C 30" Biscuit

273023C 36" Black

273601C 36" White

273602C 36" Biscuit

273623C 36" Black

.ONYEK.ONYEK

.ONYEK

.ONYEK.ONYEKREBMUNTRAPREBMUNTRAP

REBMUNTRAP

REBMUNTRAPREBMUNTRAPNOITPIRCSEDNOITPIRCSED

NOITPIRCSED

NOITPIRCSEDNOITPIRCSED.YTQ.YTQ

.YTQ

.YTQ.YTQ

183000439"8/7,gnihsuB1

216000499"8/5,ocyeHtilpS,gnihsuB1

342000499"2/1,ocyeH,gnihsuB1

421007439relloR1

583211079nwoD/pU,ylbmessAhctiwS1

641701079lortnoCdeepS,ssenraHeriW1

71940629923-8/3,tuN1

856106399bonK1

948400199rotalosnIrotoM3

0127990079ylbmessAtekcarBhctiwSrewoL1

1139211079eriWdnuorGneerG1

2139901079ssenraHeriW1

6124670089etalPpu-kcaB1

7108770089knarC1

8186180089revoChctiwS1

9152311079)0372ledoM(edilShtiwylbmessAyenmihC1

62311079)6372ledoM(edilShtiwylbmessAyenmihC1

0226308099)37.oNyeK-roticapaChtiw(rotoM1

1274202099leehWrewolB1

2276180089noisnetxExoBllorcS1

3223001799recapS3

4295211079thgiR,ylbmessAtekcarBpoT1

5206211079tfeL,ylbmessAtekcarBpoT1

6222311079)0372ledoM(sselniatS,poT1

32311079)6372ledoM(sselniatS,poT1

8219901079ylbmessAxoBllorcS1

9234411079revoCrotoMraeG1

0349901079)0372ledoM(ylbmessAxoBriA1

29901079)6372ledoM(ylbmessAxoBriA1

1305180089revoCxoBllorcS1

2375180089partSroticapaC1

3368790079)sretilf2sniatnoc()0372ledoM(tiKretliF1

78790079)sretilf2sniatnoc()6372ledoM(tiKretliF1

5450909099paCdnE1

6459208099rotomraeG1

7405801199pirtSedilS4

9454207199DHSWXHTLS573.x81-8#,wercS91

0517405199HRDBSWXH005.x23-01#,wercS2

1519405199HRTHPRS573.x81-8#,wercS6

2588405199mirTHP5.oN005.x81-8#,wercS2

3585180089)0372ledoM(gninepOxoBriA,revoC1

58180089)6372ledoM(gninepOxoBriA,revoC1

458840629942-01#,tuN4

5544180089)0372ledoM(revoCxoBriA1

96180089)6372ledoM(revoCxoBriA1

6500511079ylbmessAtekcarBrotomraeG1

7595180089troppuSgeL2

856350519961/5x02-4/1,wercS5

95729052994/1,rehsaW2

0652206199SMDHHP2/1x23-8#,wercS4

1665306199KCOLHWHS8/3x42-01#,wercS1

2616306199DLDHLFHP8/3x42-01#,wercS1

4673406299SPEKXEH42-01,tuN7

5677406299KCOLZIHW02-4/1,tuN3

663360839942-01,tloB-U1

7684000499feileRniartS1

8674406239egnalFxeH,tuN1

0751480089pmalClennahCeriW2

1739407239eiTeriW3

3700017299roticapaC1

4728306199DHXEH052.1x02-4/1,wercS2

5751405199TPBDHRTHP052.x81-8#2

4830500199)"03(maoF-laeS1

40500199)"63(maoF-laeS1

**11311079.soNyeKsedulcnI(etelpmoC,ylbmessArewolB

)37&,56,46,85,94,23,13,82,22,12,02,9,2

**02311079)0372ledoM(etelpmoC,ylbmessAyenmihC

)17&,25,15,54,91,8,5.soNyeKsedulcnI(

**12311079)6372ledoM(etelpmoC,ylbmessAyenmihC

)17&,25,15,54,91,8,5.soNyeKsedulcnI(

SERVICE PARTS

Models 2730 & 2736

Downdraft Blower Systems

WARRANTY

BROAN-NUTONE ONE YEAR LIMITED WARRANTY

Broan-NuTone warrants to the original consumer purchaser of its products that such

products will be free from defects in materials or workmanship for a period of one year from

the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR

IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MER-

CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

During this one-year period, Broan-NuTone will, at its option, repair or replace, without

charge, any product or part which is found to be defective under normal use and service.

THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS AND

TUBES. This warranty does not cover (a) normal maintenance and service or (b) any

products or parts which have been subject to misuse, negligence, accident, improper

maintenance or repair (other than by Broan-Nutone), faulty installation or installation contrary

to recommended installation instructions.

The duration of any implied warranty is limited to the one-year period as specified for the

express warranty. Some states do not allow limitation on how long an implied warranty lasts,

so the above limitation may not apply to you.

BROAN-NUTONE’S OBLIGATION TO REPAIR OR REPLACE, AT BROAN-NUTONE'S

OPTION, SHALL BE THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER

THIS WARRANTY. BROAN-NUTONE SHALL NOT BE LIABLE FOR INCIDENTAL,

CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION

WITH PRODUCT USE OR PERFORMANCE. Some states do not allow the exclusion or

limitation of incidental or consequential damages, so the above limitation or exclusion may

not apply to you.

This warranty gives you specific legal rights, and you may also have other rights, which vary

from state to state. This warranty supersedes all prior warranties.

To qualify for warranty service, you must (a) notify Broan-Nutone at the address stated below

or telephone: 1-800-637-1453, (b) give the model number and part identification and (c)

describe the nature of any defect in the product or part. At the time of requesting warranty

service, you must present evidence of the original purchase date.

Broan-NuTone LLC, 926 West State Street, Hartford, WI 53027 (1-800-637-1453)

NuTone, Inc., 4820 Red Bank Road, Cincinnati, OH 45227 (1-800-543-8687)

99041818L

NuTone ECLIPSE 2730 Manuale utente

Marca: NuTone

Modello: ECLIPSE 2730

Categoria: Aeratori / essiccatori

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: NuTone ECLIPSE 2730 User manual

NuTone ECLIPSE 2730 Manuale utente

NuTone ECLIPSE 2730 Manuale utente

in altre lingue

Altri documenti