Printek Printer 4000se Manuale utente

FormsPro 4000se Series

Operator’s Manual

©Printek, Inc. 2003

1517 Townline Road

Benton Harbor, MI 49022

(800) 368-4636

www.printek.com

Part Number 5593

ii

This equipment has been tested and found to comply with the limits for a Class A

Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference in which case the user will be

required to correct the interference at his own expense.

The user is cautioned that any changes or modifications not expressly approved by

the party responsible for compliance could void the user's authority to operate the

equipment.

This digital apparatus does not exceed the Class A limits for radio noise emissions as

set out by the ICES-003 standard, of the Canadian Department of Communications.

Cet appareil numérique n’émet pas de bruits radioélectroiques depassant les limites

de Classe A prescrites dans la norme NMB-003 Édictée par le Ministre des

Communications du Canada.

Acknowledgments:

IBM and Proprinter are registered trademarks of International Business Machines

Co.; DEC is a registered trademark of Digital Equipment Corporation; Epson is a

registered trademark of Seiko Epson; QMS is a registered trademark of Quality Micro

Systems, Inc.; IGP is a registered trademark of Printronix Corp.; Printek is a registered

trademark of Printek, Inc.

Specifications are subject to change without notice.

iii

Read all setup and operating instructions before

proceeding with operation.

Operate printer only on a firm, solid surface.

Do not operate in an enclosure unless properly ventilated. Make sure no

ventilation openings are blocked or obstructed, which may result in the

printer overheating.

Do not operate near a heat source.

No user-serviceable parts inside. Refer service or

repairs to a qualified service professional.

Use of genuine Printek replacement parts is required to warrant proper,

safe operation.

Any alteration or modification of this device voids the user warranty and

may make the product unsafe to operate.

The printhead and motors get hot during use. Wait until they cool before

touching them.

Make certain the printer is disconnected from AC power before removing

any covers or performing any required cleaning or maintenance.

Connecting this printer to an ungrounded receptacle can result in electrical

shock.

Never place the printer near inflammable or explosive substances. Do not

operate near liquid or spill liquid into the printer at any time.

iv

Lesen Sie vor der Inbetriebnahme die Aufbau-

und Bedienungsanleitung.

Der Drucker muss zum Betrieb auf einer festen, soliden Oberfläche stehen.

Betreiben Sie den Drucker nicht in einem kleinen, geschlossenen Raum, es

sei denn dieser wird ordnungsgemäß belüftet. Achten Sie darauf, dass die

Lüftungen nicht blockiert oder versperrt sind, denn dies kann zum

Überhitzen des Druckers führen.

Nehmen Sie den Drucker nicht in der Nähe einer Wärmequelle in Betrieb.

Enthält keine Teile, die vom Bediener instandgesetzt

werden können. Bitte wenden Sie sich bei Instandsetzung oder Reparatur

an qualifiziertes Kundendienstpersonal.

Die Verwendung von echten Printek Ersatzteilen ist notwendig, um

ordnungsgemäßen, sicheren Betrieb zu gewährleisten.

Änderungen oder Modifikationen dieses Geräts machen die Garantie

ungültig und können den sicheren Betrieb des Produkts gefährden.

Während des Druckens werden Druckerkopf und Motoren heiß. Warten

Sie, bis sich die Teile abgekühlt haben, bevor Sie sie berühren.

Vergewissern Sie sich, dass der Drucker nicht mehr an die Stromquelle

angeschlossen ist, bevor Sie Abdeckungen abnehmen oder das Gerät

reinigen bzw. warten.

Schließen Sie diesen Drucker nicht an eine ungeerdete Steckdose an; dies

kann zum Elektroschock führen.

Setzen Sie den Drucker niemals in die Nähe von feuer- oder

explosionsgefährlichen Stoffen. Betreiben Sie den Drucker nicht in der

v

Nähe von Flüssigkeiten und lassen Sie keine Flüssigkeiten in den Drucker

gelangen.

TABLE OF CONTENTS

INTRODUCTION 1

Models and Options 1

Manual Contents 2

GETTING STARTED 5

Installation 5

Interface Set Up 6

RS-232C Serial Interface 7

Parallel Interface 8

Ethernet 10/100BaseT Print Server 9

Wireless Ethernet Print Server 9

Installing The Ribbon Cartridge 10

Why Use Only Printek

®

Brand Ribbons 10

Ribbon Installation 11

Loading Paper 14

FormsPro 4300se & 4500se Single Tractor Model 14

FormsPro 4503se Tri-Trak Model 16

Printer Self-Test 18

DAILY OPERATION 19

Introduction 19

Control Panel Features 20

LCD Display and Indicators 21

Control Panel Buttons 22

Selecting And Loading Forms 25

Selecting a Form Already Loaded In the Tractors 25

Loading a New or Different Form In the Tractors 25

Ejecting And Tearing Off A Form 30

Installing A New Ribbon Cartridge 33

Removing the Old Ribbon Cartridge 33

Installing the New Ribbon Cartridge 34

Aligning Print 36

vi

Common Error Conditions 39

Check Paper 39

No Paper to Load 39

Too Much Paper to Unload 40

Selected Form is not Loaded 40

No Ribbon or Wrong Ribbon 40

Ribbon Lid Open 40

Change Ribbon 40

Other Errors 41

PRINTER CONFIGURATION 43

Introduction To Setup 43

Setup Buttons 43

Entering Setup 44

Using the SETUP Button 44

Using the FUNCTION and VALUE Buttons 44

Exiting Setup 45

Forms Menu 46

Forms Menu Items 46

Interface Menu 54

Entering the Interface Menu 54

RS-232C Serial Interface Items 55

Parallel/LAN Interface Items 59

Options Menu 63

ImagerPlus Graphic Card 68

Test Menu 73

FORM CONSTRUCTION 75

Form Construction 75

Form Layout Considerations 76

MAINTENANCE AND TROUBLESHOOTING 77

Error Messages 77

Preventive Maintenance 78

Obtaining Service 78

ADVANCED SETUP FEATURES 81

Security Menu 81

USING REMOTE SETUP 83

Remote Setup via Windows Application 83

Remote Setup via Generic Text File 83

vii

USING THE OPTIONAL SETUP MODULE 91

Introduction 91

Setup Module Installation 91

PRINTER RESET CONDITIONS 95

CONTROL CODE AND ESCAPE SEQUENCE

SUMMARIES 97

Genicom 3840 and 3410 Emulation 97

ANSI X3.64 Emulation 98

Epson Fx Emulation 99

IBM Proprinter Emulation 101

LA-120/210 Emulation 102

Simple TTY Emulation 103

Printek Emulation 104

ASCII CHARACTER TABLES 105

SPECIFICATIONS 111

GLOSSARY OF TERMS 117

1

INTRODUCTION

Thank you for purchasing a Printek FormsPro 4000se Series Printer.

This printer has been designed to provide years of service handling your

most demanding printing requirements.

The FormsPro 4000se Series printers offer higher throughput than all other

printers in its class. In addition, an easy to use front panel combined with

the ability to store ten different form configurations makes handling multiple

forms as simple as a button press for the operator.

Models and Options

The FormsPro 4300se, 4500se and the FormsPro 4503se differ only in the

number of tractor paths available, one path or three.

Options available for both models include:

• Ethernet 10/100BaseT Print Server

• Wireless Ethernet Print Server

• Imager Bar Code Co-processor

• ImagerPlus Bar Code Co-processor

• Print Stand (required for reduced sound levels)

• External FormsCutter

• Setup Module

• Sound Enclosure

INTRODUCTION

2

Manual Contents

*Unless specifically noted, all instructions and information herein is

valid for all models in the 4000se series.

• GETTING STARTED provides instructions for installation, setting up

the computer interface, installing the ribbon cartridge, loading paper,

and performing a printer self-test.

• DAILY OPERATION provides more detailed descriptions of the

features that are used most frequently. These include the “every day”

buttons and indicators on the control panel, selecting or loading new

forms, ejecting forms, changing the ribbon cartridge, aligning print with

preprinted forms, and causes for common error conditions.

• PRINTER CONFIGURATION provides detailed information on how

to use Setup to permanently store parameters for each of the ten

forms, parameters for the standard and optional interfaces, and

parameters for other options.

• SPECIFYING FORMS provides tips for form construction and layout.

• MAINTENANCE AND TROUBLESHOOTING lists more serious

error messages than discussed in the Daily Operation section,

preventive maintenance, and how to obtain service.

• ADVANCED SETUP FEATURES provides information on how to set

menu security.

• USING REMOTE SETUP describes how to “set up” default

parameters from a host computer.

• USING THE SETUP MODULE describes how the optional Setup

Module can be used to copy Setup parameters from one printer to

another.

• PRINTER RESET CONDITIONS describes the state of the printer

after power up or reset.

INTRODUCTION

3

• CONTROL CODE AND ESCAPE SEQUENCE SUMMARIES lists

the commands supported for each printer emulation.

• ASCII CHARACTER TABLES show the characters for each

character set.

• SPECIFICATIONS list the operating ranges and ratings of the printer.

• GLOSSARY OF TERMS provides definitions for terms used in this

manual.

5

GETTING STARTED

This chapter will use the fewest possible steps to get the first time user up

and running quickly. You will be guided through the following steps:

• Finding a suitable location and installing the printer

• Setting up a host interface if necessary

• Installing the ribbon cartridge

• Loading paper

• Performing a printer self-test

Installation

Before installation, a suitable site must be chosen. Suitable sites include

offices, computer rooms, and most factory environments. The Printek

FormsPro 4000se printers have been designed to be rugged, heavy-duty

printers. As such, they will handle most harsh environments, but should not

be placed in direct sunlight or in areas that will exceed the rated

temperature, humidity, or power requirements. For details, refer to

“SPECIFICATIONS” on 111.

Once a site has been selected, the printer should be placed on a Printek

print stand. The Printek print stand is especially recommended for the

FormsPro 4503se and is required to meet the low noise rating of the

printer. Of course, another sturdy print stand or table with a slotted top for

feeding paper into the bottom of printer may be used.

The print stand should be located in an area large enough to provide easy

access to both the front of the printer and the rear for accessing printed

output. Unpack the printer as described in the “FormsPro 4000se series

Unpacking Instructions” and place the printer on the print stand.

GETTING STARTED

6

Note: Placing the printer on the print stand is best accomplished

with two people. Proper lifting technique should be observed.

Caution: Before connecting or turning on power, make sure that all

shipping materials have been removed. These materials include

a cable tie that secures the print head carriage (open ribbon lid

to access) and remove the cable tie securing the front panel to

the base. When unpacking a FormsPro 4503se, open the front

of the unit by releasing the latch panel of the printer. Remove

the two cable ties securing the tractor shuttle to the front of the

lower side plates, and the two ties located toward the rear of

the shuttle assembly.

Next, connect the power cord supplied with the printer to the printer and an

appropriate power outlet. Now connect the computer cable to the

appropriate interface on the rear panel of the printer.

Interface Set Up

Depending upon which interface is being used to connect the printer to the

host computer, some set up may or may not be required. This is true of the

standard parallel or serial ports The factory default settings for each

interface should work well for most installations. However, the following

paragraphs provide some basic information about each interface and also

refer to the page number in the Configuration chapter where all the details

for each interface are described. If you need to make changes to the

default settings, please refer to “Introduction to Setup” on page 43 for

instructions on how to access the printer’s Setup menus.

Once you are comfortable that the interface settings match those required

by your computer, proceed to the next section, “Installing the Ribbon

Cartridge” on page 10.

GETTING STARTED

7

RS-232C Serial Interface

This interface uses a 25 pin “D” connector as described below. The default

settings are 9600 baud, 8 data bits, 1 stop bit, and no parity with hardware

handshake on pin 11. The default printer emulation is Epson. For a

complete description of all the default settings for this interface, refer to

page 55.

Pin Signal

1

2

3

4

5

6

7

8

11

20

Chassis ground.

Transmit data. (Printer output).

Receive data. (Printer input).

Request to send (set). (Printer output).

Clear to send (ignored). (Printer input).

Data set ready (ignored). (Printer input).

Signal ground.

Carrier detect (ignored). (Printer input).

Printer busy. (Printer output).

Data terminal ready. (Printer output).

RS-232C Serial Interface Connector.

GETTING STARTED

8

Parallel Interface

This interface uses the standard 36 pin parallel connector as shown below.

The default printer emulation is Epson.

Signal Pin

Signal

1

19

2

20

3

21

4

22

5

23

6

24

7

25

8

26

9

27

____________________

DATA STROBE

DATA STROBE RTN

DATA 1

DATA 1 RETURN

DATA 2

DATA 2 RETURN

DATA 3

DATA 3 RETURN

DATA 4

DATA 4 RETURN

DATA 5

DATA 5 RETURN

DATA 6

DATA 6 RETURN

DATA 7

DATA 7 RETURN

DATA 8

DATA 8 RETURN

10

28

11

29

12

13

14

16

17

18

31

30

32

35

36

_______________________

ACKNOWLEDGE

ACKNLG RETURN

BUSY

BUSY RETURN

PAPER ERROR

SELECT

________________

AUTO FEED

±0V

CHASSIS GROUND

+5V at 200mA Max.

______

INIT

INIT RTN

_________

FAULT

+5V LOGIC HIGH

______________

SELECT IN

Parallel Interface Connector

GETTING STARTED

9

Ethernet 10/100BaseT Print Server

This interface uses a standard RJ-45 connector and the default printer

emulation is Epson. For a complete description of all the default settings for

this interface, refer to “Parallel/LAN Interface Items” on page 59. For

additional software installation and operational information, please refer to

the Troy XCD Quick Install Manual shipped with the unit.

Wireless Ethernet Print Server

This interface is intended for 802.11b wireless connectivity. It may also be

used with conventional CAT-5 twisted pair wiring, using the standard RJ-

45 connector. The interface automatically senses when a CAT-5 connection

is present and will disable the wireless capability.

For additional software installation and operational information, please refer

to the Printek Wireless Ethernet Print Server Manual shipped with the unit.

GETTING STARTED

10

Installing The Ribbon Cartridge

The Printek FormsPro printer has been designed to make installing Printek

brand ribbons a simple, clean process. Unlike other printers, there is no

need to touch the ribbon fabric or deal with difficult to position ribbon

guides. The following sections explain why the use of Printek brand ribbons

should be important to you and will guide you through installing the ribbon

cartridge.

Why Use Only Printek

®

Brand Ribbons

Printek

®

Brand Ribbon Label

The above label on each ribbon can identify Printek brand ribbons. There

are many reasons to use only Printek brand ribbons in your FormsPro

4000se Series printer. First of all, using only Printek brand ribbons

will automatically extend the print head warranty to two years.

The reason this is possible is that Printek brand ribbons are manufactured to

much higher quality standards than those offered by other manufacturers.

This provides not only longer print head life, but also longer ribbon life… 23

million characters as compared to only 15 million characters from some

generic ribbons.

Remember that using only Printek brand ribbons is important because the

wear that is started and the contamination that remains from even one

inferior ribbon will continue to damage the print head. Also, damage to

other printer components that is caused by the use of non-Printek ribbons

will not be covered by the printer’s warranty.

REORDER NUMBER 90729

FOR NEAREST DISTRIBUTOR

CALL 1-800-368-4636

GETTING STARTED

11

Using inferior ribbons would be like using poor quality fuel in your

automobile. Premature engine failure and poor performance leading up to

the failure would be the best you could expect.

Other useful features available only with the use of Printek brand ribbons

are that the printer will not allow printing if a ribbon is not installed, and the

printer will alert the operator when a ribbon needs to be changed.

Ribbon Installation

1. Open the ribbon lid on top of the printer and position the print head

for ribbon loading by lifting the ribbon loading handle as indicated in

the following picture.

1. Opening the Ribbon Loading Handle

2. Ribbon Support Brackets

2. Remove the new ribbon from its plastic bag and make sure the

ribbon fabric is taut by turning the knob on top of the ribbon

cartridge in a counterclockwise direction as indicated by the arrow

on the cartridge.

1

2

GETTING STARTED

12

3. Place the right hand end of the ribbon on the support bracket while

you align the plastic tabs with the slots in the bracket as shown

below.

Installing the Ribbon Cartridge

4. Align and lower the left end of the ribbon onto the left support

bracket until it snaps into place, while guiding the ribbon fabric

between the nose of the print head and the ribbon guide pins.

Continue to lower the cartridge until the tab on the left end of the

cartridge snaps into place.

La pagina sta caricando ...

Printek Printer 4000se Manuale utente

Questo manuale è adatto anche per

Printek Printer 4000se Manuale utente

in altre lingue

Documenti correlati

Altri documenti