Gigabyte GA-H110M-H Manuale del proprietario

Marca: Gigabyte

Modello: GA-H110M-H

Tipo: Manuale del proprietario

For more product details, please visit GIGABYTE's website.

https://www.gigabyte.com/Motherboard/GA-H110M-H-rev-1x#kf

GIGABYTE will reduce paper use in order to fulll the responsibilities of a global citizen.

Also, to reduce the impacts on global warming, the packaging materials of this product

are recyclable and reusable. GIGABYTE works with you to protect the environment.

GA-H110M-H

User's Manual

Rev. 1201

The trademarks mentioned in this manual are legally registered to their respective owners.

Disclaimer

Information in this manual is protected by copyright laws and is the property of GIGABYTE.

Changes to the specications and features in this manual may be made by GIGABYTE without

prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or

published in any form or by any means without GIGABYTE's prior written permission.

For detailed product information, carefully read the User's Manual.

For quick set-up of the product, refer to the Quick Installation Guide on GIGABYTE's

website.

https://download.gigabyte.com/FileList/Manual/mb_manual_installation-guide_103.pdf?m=sw

For product-related information, check on our website at: https://www.gigabyte.com

Identifying Your Motherboard Revision

The revision number on your motherboard looks like this: "REV: X.X." For example, "REV: 1.0"

means the revision of the motherboard is 1.0. Check your motherboard revision before updating

motherboard BIOS, drivers, or when looking for technical information.

Example:

- 3 -

Table of Contents

Chapter 1 Product Introduction .......................................................................................4

1-1 Motherboard Layout ......................................................................................... 4

Chapter 2 Hardware Installation .....................................................................................5

2-1 Installation Precautions .................................................................................... 5

2-2 Product Specications ...................................................................................... 6

2-3 Installing the CPU ............................................................................................ 9

2-4 Installing the Memory ....................................................................................... 9

2-5 Installing an Expansion Card ......................................................................... 10

2-6 Back Panel Connectors .................................................................................. 10

2-7 Internal Connectors ........................................................................................ 12

Chapter 3 BIOS Setup ..................................................................................................18

3-1 Startup Screen ............................................................................................... 18

3-2 M.I.T. .............................................................................................................. 19

3-3 System Information ........................................................................................ 25

3-4 BIOS Features ............................................................................................... 26

3-5 Peripherals ..................................................................................................... 29

3-6 Chipset ........................................................................................................... 31

3-7 Power Management ....................................................................................... 32

3-8 Save & Exit ..................................................................................................... 34

Chapter 4 Installing the Operating System and Drivers ................................................ 35

Regulatory Notices .................................................................................................... 36

Contact Us ................................................................................................................ 37

- 4 -

KB_MS CPU_FAN

SYS_FAN

LGA1151

ATX

GA-H110M-H

F_AUDIO

AUDIO

DDR4_1

DDR4_2

BAT

ATX_12V

Intel® H110

F_USB30

R_USB30

CODEC

CLR_CMOS

M_BIOS

VGA

HDMI

USB_LAN

PCIEX16

PCIEX1_1

PCIEX1_2

iTE®

Super I/O

Realtek®

GbE LAN

F_USB1

TPM F_USB2 F_PANEL

SATA3 1 3

0 2

SPDIF_O

1-1 Motherboard Layout

Chapter 1 Product Introduction

2-1 Installation Precautions

The motherboard contains numerous delicate electronic circuits and components which can become

damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user's

manual and follow these procedures:

•Prior to installation, make sure the chassis is suitable for the motherboard.

•Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or

warranty sticker provided by your dealer. These stickers are required for warranty validation.

•Always remove the AC power by unplugging the power cord from the power outlet before

installing or removing the motherboard or other hardware components.

•When connecting hardware components to the internal connectors on the motherboard, make

sure they are connected tightly and securely.

•When handling the motherboard, avoid touching any metal leads or connectors.

•It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic

components such as a motherboard, CPU or memory. If you do not have an ESD wrist strap,

keep your hands dry and rst touch a metal object to eliminate static electricity.

•Prior to installing the motherboard, please have it on top of an antistatic pad or within an

electrostatic shielding container.

•Before connecting or unplugging the power supply cable from the motherboard, make sure

the power supply has been turned off.

•Before turning on the power, make sure the power supply voltage has been set according to

the local voltage standard.

•Before using the product, please verify that all cables and power connectors of your hardware

components are connected.

•To prevent damage to the motherboard, do not allow screws to come in contact with the

motherboard circuit or its components.

•Make sure there are no leftover screws or metal components placed on the motherboard or

within the computer casing.

•Do not place the computer system on an uneven surface.

•Do not place the computer system in a high-temperature or wet environment.

•Turning on the computer power during the installation process can lead to damage to system

components as well as physical harm to the user.

•If you are uncertain about any installation steps or have a problem related to the use of the

product, please consult a certied computer technician.

•If you use an adapter, extension power cable, or power strip, ensure to consult with its

installation and/or grounding instructions.

Chapter 2 Hardware Installation

- 5 -

2-2 ProductSpecications

CPU Support for Intel® Core™ i7 processors/Intel® Core™ i5 processors/

Intel® Core™ i3 processors/Intel® Pentium® processors/

Intel® Celeron® processors in the LGA1151 package

(Go to GIGABYTE's website for the latest CPU support list.)

L3 cache varies with CPU

Chipset Intel® H110 Express Chipset

Memory 2 x DDR4 DIMM sockets supporting up to 32 GB of system memory

* Due to a Windows 32-bit operating system limitation, when more than 4 GB of physical

memory is installed, the actual memory size displayed will be less than the size of

the physical memory installed.

Dual channel memory architecture

Support for DDR4 2133 MHz memory modules

Support for ECC UDIMM 1Rx8/2Rx8 memory modules (operate in non-ECC mode)

Support for non-ECC UDIMM 1Rx8/2Rx8/1Rx16 memory modules

(Go to GIGABYTE's website for the latest supported memory speeds and memory

modules.)

Onboard

Graphics

Integrated Graphics Processor-Intel® HD Graphics support:

- 1 x D-Sub port, supporting a maximum resolution of 1920x1200@60 Hz

- 1 x HDMI port, supporting a maximum resolution of 4096x2160@24 Hz

* Support for HDMI 1.4 version.

Maximum shared memory of 512 MB

Audio Realtek® Audio CODEC

High Denition Audio

2/4/5.1/7.1-channel

* You can change the functionality of an audio jack using the audio software. To congure

7.1-channel audio, access the audio software for audio settings.

Support for S/PDIF Out

LAN Realtek® GbE LAN chip (1 Gbps/100 Mbps)

Expansion Slots 1 x PCI Express x16 slot, running at x16

(The PCI Express x16 slot conforms to PCI Express 3.0 standard.)

2 x PCI Express x1 slots

(All of the PCI Express x1 slots conform to PCI Express 2.0 standard.)

Storage Interface Chipset:

- 4 x SATA 6Gb/s connectors

USB Chipset:

- 4 x USB 3.0/2.0 ports (2 ports on the back panel, 2 ports available through

the internal USB header)

- 6 x USB 2.0/1.1 ports (2 ports on the back panel, 4 ports available through

the internal USB headers)

- 6 -

Internal

Connectors

1 x 24-pin ATX main power connector

1 x 4-pin ATX 12V power connector

4 x SATA 6Gb/s connectors

1 x CPU fan header

1 x system fan header

1 x front panel header

1 x front panel audio header

1 x S/PDIF Out header

1 x USB 3.0/2.0 header

2 x USB 2.0/1.1 headers

1 x Trusted Platform Module (TPM) header

1 x Clear CMOS jumper

Back Panel

Connectors

1 x PS/2 mouse port

1 x PS/2 Keyboard port

1 x D-Sub port

1 x HDMI port

2 x USB 3.0/2.0 ports

2 x USB 2.0/1.1 ports

1 x RJ-45 port

3 x audio jacks

I/O Controller iTE® I/O Controller Chip

Hardware

Monitor

System voltage detection

Temperature detection

Fan speed detection

Overheating warning

Fan fail warning

Fan speed control

* Whether the fan speed control function is supported will depend on the cooler you

install.

BIOS 1 x 64 Mbit ash

Use of licensed AMI UEFI BIOS

PnP 1.0a, DMI 2.7, WfM 2.0, SM BIOS 2.7, ACPI 5.0

- 7 -

Unique Features Support for APP Center

* Available applications in APP Center may vary by motherboard model. Supported

functions of each application may also vary depending on motherboard specications.

- 3D OSD

- @BIOS

- AutoGreen

- Cloud Station

- EasyTune

- Fast Boot

- Smart TimeLock

- Smart Keyboard

- Smart Backup

- System Information Viewer

- USB Blocker

Support for Q-Flash

Support for Smart Switch

Bundled

Software

Norton® Internet Security (OEM version)

LAN bandwidth management software

Operating

System Support for Windows 10/8.1/7

Form Factor Micro ATX Form Factor; 22.6cm x 17.4cm

* GIGABYTE reserves the right to make any changes to the product specications and product-related information without

prior notice.

&Please visit GIGABYTE's website for support lists of CPU, memory modules, and SSDs.

https://www.gigabyte.com/Motherboard/GA-H110M-H-rev-1x?m=dl#support-dl

&Please visit the SERVICE/SUPPORT\Utility page on GIGABYTE's website to download the latest version

of apps.

https://www.gigabyte.com/Support/Utility/Motherboard?m=ut

- 8 -

DualChannelMemoryConguration

This motherboard provides two memory sockets and supports Dual Channel Technology. After the memory

is installed, the BIOS will automatically detect the specications and capacity of the memory. Enabling Dual

Channel memory mode will double the original memory bandwidth.

2-3 Installing the CPU

2-4 Installing the Memory

Read the following guidelines before you begin to install the memory:

•Make sure that the motherboard supports the memory. It is recommended that memory of the same

capacity, brand, speed, and chips be used.

(Go to GIGABYTE's website for the latest supported memory speeds and memory modules.)

•Always turn off the computer and unplug the power cord from the power outlet before installing the

memory to prevent hardware damage.

•Memory modules have a foolproof design. A memory module can be installed in only one direction.

If you are unable to insert the memory, switch the direction.

Read the following guidelines before you begin to install the CPU:

•Make sure that the motherboard supports the CPU.

(Go to GIGABYTE's website for the latest CPU support list.)

•Always turn off the computer and unplug the power cord from the power outlet before installing the

CPU to prevent hardware damage.

•Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. (Or you may

locate the notches on both sides of the CPU and alignment keys on the CPU socket.)

•Apply an even and thin layer of thermal grease on the surface of the CPU.

•Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and damage

of the CPU may occur.

•Set the CPU host frequency in accordance with the CPU specications. It is not recommended

that the system bus frequency be set beyond hardware specications since it does not meet the

standard requirements for the peripherals. If you wish to set the frequency beyond the standard

specications, please do so according to your hardware specications including the CPU, graphics

card, memory, hard drive, etc.

Installing the CPU

Locate the alignment keys on the motherboard CPU socket and the notches on the CPU.

Do not remove the CPU socket cover before inserting the CPU. It may pop off from the load

plate automatically during the process of re-engaging the lever after you insert the CPU.

Alignment KeyAlignment Key

LGA1151 CPU Socket

Pin One Corner of the CPU Socket

LGA1151 CPU

Triangle Pin One Marking on the CPU

Notch

&Please visit GIGABYTE's website for details on hardware installation.

http://www.gigabyte.com/WebPage/210/quick-guide.html?m=sw

- 9 -

Due to CPU limitations, read the following guidelines before installing the memory in Dual Channel mode.

1. Dual Channel mode cannot be enabled if only one memory module is installed.

2. When enabling Dual Channel mode with two memory modules, it is recommended that memory of

the same capacity, brand, speed, and chips be used for optimum performance.

The two DDR4 memory sockets are divided into two channels and each channel has one memory socket as

following:

Channel A: DDR4_1

Channel B: DDR4_2

2-5 Installing an Expansion Card

Read the following guidelines before you begin to install an expansion card:

•Make sure the motherboard supports the expansion card. Carefully read the manual that came

with your expansion card.

•Always turn off the computer and unplug the power cord from the power outlet before installing an

expansion card to prevent hardware damage.

2-6 Back Panel Connectors

PS/2 Keyboard and PS/2 Mouse Port

Use the upper port (green) to connect a PS/2 mouse and the lower port (purple) to connect a PS/2 keyboard.

D-Sub Port

The D-Sub port supports a 15-pin D-Sub connector and supports a maximum resolution of

1920x1200@60 Hz (the actual resolutions supported depend on the monitor being used). Connect a

monitor that supports D-Sub connection to this port.

HDMI Port

The HDMI port is HDCP compliant and supports Dolby True HD and DTS HD

Master Audio formats. It also supports up to 192KHz/16bit 8-channel LPCM

audio output. You can use this port to connect your HDMI-supported monitor. The maximum supported

resolution is 4096x2160@24 Hz, but the actual resolutions supported are dependent on the monitor

being used.

After installing the HDMI device, make sure to set the default sound playback device to HDMI.

(The item name may differ depending on your operating system.)

USB 3.0/2.0 Port

The USB 3.0 port supports the USB 3.0 specication and is compatible to the USB 2.0/1.1 specication.

Use this port for USB devices.

•When removing the cable connected to a back panel connector, rst remove the cable from your

device and then remove it from the motherboard.

•When removing the cable, pull it straight out from the connector. Do not rock it side to side to prevent

an electrical short inside the cable connector.

- 10 -

RJ-45 LAN Port

The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following

describes the states of the LAN port LEDs.

USB 2.0/1.1 Port

The USB port supports the USB 2.0/1.1 specication. Use this port for USB devices.

Line In/Rear Speaker Out (Blue)

The line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.

Line Out/Front Speaker Out (Green)

The line out jack.

Mic In/Center/Subwoofer Speaker Out (Pink)

The Mic in jack.

Audio Jack Congurations:

Jack Headphone/

2-channel 4-channel 5.1-channel 7.1-channel

Line In/Rear Speaker Out aaa

Line Out/Front Speaker Out a a a a

Mic In/Center/Subwoofer

Speaker Out a a

Front Panel Line Out/Side

Speaker Out a

Speed LED Activity LED

LAN Port

Speed LED:

State Description

Orange 1 Gbps data rate

Green 100 Mbps data rate

Off 10 Mbps data rate

Activity LED:

State Description

Blinking Data transmission or receiving is occurring

Off No data transmission or receiving is occurring

&Please visit GIGABYTE's website for details on conguring the audio software.

https://www.gigabyte.com/WebPage/697/realtek897-audio.html

You can change the functionality of an audio jack using the audio software. To congure 7.1-channel

audio, access the audio software for audio settings.

- 11 -

2-7 Internal Connectors

Read the following guidelines before connecting external devices:

•First make sure your devices are compliant with the connectors you wish to connect.

•Before installing the devices, be sure to turn off the devices and your computer. Unplug the power

cord from the power outlet to prevent damage to the devices.

•After installing the device and before turning on the computer, make sure the device cable has

been securely attached to the connector on the motherboard.

1) ATX_12V

2) ATX

3) CPU_FAN

4) SYS_FAN

5) SATA3 0/1/2/3

6) F_PANEL

7) F_AUDIO

8) SPDIF_O

9) CLR_CMOS

10) F_USB30

11) F_USB1/F_USB2

12) TPM

13) BAT

9 6

11 131287

1 3

- 12 -

DEBUG

PORT

G.QBOFM

131

ATX

1/2) ATX_12V/ATX (2x2 12V Power Connector and 2x12 Main Power Connector)

With the use of the power connector, the power supply can supply enough stable power to all the components

on the motherboard. Before connecting the power connector, rst make sure the power supply is turned

off and all devices are properly installed. The power connector possesses a foolproof design. Connect the

power supply cable to the power connector in the correct orientation.

The 12V power connector mainly supplies power to the CPU. If the 12V power connector is not connected,

the computer will not start.

To meet expansion requirements, it is recommended that a power supply that can withstand high

power consumption be used (500W or greater). If a power supply is used that does not provide the

required power, the result can lead to an unstable or unbootable system.

ATX:

Pin No. Denition Pin No. Denition

1 3.3V 13 3.3V

2 3.3V 14 -12V

3 GND 15 GND

4 +5V 16 PS_ON (soft On/Off)

5 GND 17 GND

6 +5V 18 GND

7 GND 19 GND

8 Power Good 20 NC

9 5VSB (stand by +5V) 21 +5V

10 +12V 22 +5V

11 +12V (Only for 2x12-pin

ATX)

23 +5V (Only for 2x12-pin ATX)

12 3.3V (Only for 2x12-pin

ATX)

24 GND (Only for 2x12-pin ATX)

ATX_12V:

Pin No. Denition

1 GND

2 GND

3 +12V

4 +12V

3/4) CPU_FAN/SYS_FAN (Fan Headers)

All fan headers on this motherboard are 4-pin. Most fan headers possess a foolproof insertion design.

When connecting a fan cable, be sure to connect it in the correct orientation (the black connector wire is

the ground wire). The speed control function requires the use of a fan with fan speed control design. For

optimum heat dissipation, it is recommended that a system fan be installed inside the chassis.

•Be sure to connect fan cables to the fan headers to prevent your CPU and system from

overheating. Overheating may result in damage to the CPU or the system may hang.

•These fan headers are not conguration jumper blocks. Do not place a jumper cap on the headers.

CPU_FAN

DEBUG

PORT

G.QBOFM

CPU_FAN:

Pin No. Denition

1 GND

2 +12V

3 Sense

4 Speed Control

SYS_FAN:

Pin No. Denition

1 GND

2 Speed Control

3 Sense

4 VCC

SYS_FAN

DEBUG

PORT

G.QBOFM

ATX_12V

- 13 -

5) SATA3 0/1/2/3 (SATA 6Gb/s Connectors)

The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA

1.5Gb/s standard. Each SATA connector supports a single SATA device.

Pin No. Denition

1 GND

2 TXP

3 TXN

4 GND

5 RXN

6 RXP

7 GND

To enable hot-plugging for the SATA ports, refer to Chapter 3, "BIOS Setup," "Peripherals\SATA

Conguration," for more information.

SATA3

3 2

1 0

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

1 1

7 7

The front panel design may differ by chassis. A front panel module mainly consists of power switch,

reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis

front panel module to this header, make sure the wire assignments and the pin assignments are

matched correctly.

6) F_PANEL (Front Panel Header)

Connect the power switch, reset switch, speaker, chassis intrusion switch/sensor and system status indicator

on the chassis to this header according to the pin assignments below. Note the positive and negative pins

before connecting the cables.

System Status LED

S0 On

S3/S4/S5 Off

•PW (Power Switch):

Connects to the power switch on the chassis front panel. You may

congure the way to turn off your system using the power switch

(refer to Chapter 3, "BIOS Setup," "Power Management," for more

information).

•SPEAK (Speaker):

Connects to the speaker on the chassis front panel. The system reports

system startup status by issuing a beep code. One single short beep

will be heard if no problem is detected at system startup.

•PLED/PWR_LED (Power LED):

Connects to the power status indicator

on the chassis front panel. The LED is on

when the system is operating. The LED is

off when the system is in S3/S4 sleep state

or powered off (S5).

•HD (Hard Drive Activity LED):

Connects to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive

is reading or writing data.

•RES (Reset Switch):

Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer

if the computer freezes and fails to perform a normal restart.

•CI (Chassis Intrusion Header):

Connects to the chassis intrusion switch/sensor on the chassis that can detect if the chassis cover has

been removed. This function requires a chassis with a chassis intrusion switch/sensor.

•NC: No connection.

Power LED

CI-

CI+

PLED-

PW-

SPEAK+

SPEAK-

PLED+

PW+

Power LED

HD-

RES+

HD+

RES-

Hard Drive

Activity LED

Reset

Switch Chassis Intrusion

Header

Power Switch Speaker

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3  

 S3 BSSS



U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

_ SF_

B 

USB0_B

B_

B_

F_USB3

 F_USB303



_



_3U

S_

_S

SS_F 

_

_ F 

_SB

PWR_LED-

PWR_LED+

PWR_LED-

- 14 -

8) SPDIF_O (S/PDIF Out Header)

This header supports digital S/PDIF Out and connects a S/PDIF digital audio cable (provided by expansion

cards) for digital audio output from your motherboard to certain expansion cards like graphics cards and

sound cards. For example, some graphics cards may require you to use a S/PDIF digital audio cable for

digital audio output from your motherboard to your graphics card if you wish to connect an HDMI display

to the graphics card and have digital audio output from the HDMI display at the same time. For information

about connecting the S/PDIF digital audio cable, carefully read the manual for your expansion card.

Pin No. Denition

1 SPDIFO

2 GND

9) CLR_CMOS (Clear CMOS Jumper)

Use this jumper to clear the BIOS conguration and reset the CMOS values to factory defaults. To clear

the CMOS values, use a metal object like a screwdriver to touch the two pins for a few seconds.

•Always turn off your computer and unplug the power cord from the power outlet before clearing

the CMOS values.

•After system restart, go to BIOS Setup to load factory defaults (select Load Optimized Defaults) or

manually congure the BIOS settings (refer to Chapter 3, "BIOS Setup," for BIOS congurations).

Open: Normal

Short: Clear CMOS Values

7) F_AUDIO (Front Panel Audio Header)

The front panel audio header supports High Denition audio (HD). You may connect your chassis front

panel audio module to this header. Make sure the wire assignments of the module connector match the

pin assignments of the motherboard header. Incorrect connection between the module connector and the

motherboard header will make the device unable to work or even damage it.

Some chassis provide a front panel audio module that has separated connectors on each wire

instead of a single plug. For information about connecting the front panel audio module that has

different wire assignments, please contact the chassis manufacturer.

Pin No. Denition Pin No. Denition

1 MIC L 6 MIC Detection

2 GND 7 SENSE_SEND

3 MIC R 8 No Pin

4 NC 9 Head Phone L

5 Head Phone R 10 Head Phone Detection

- 15 -

12) TPM (Trusted Platform Module Header)

You may connect a TPM (Trusted Platform Module) to this header.

Pin No. Denition Pin No. Denition

1 LCLK 11 LAD0

2 GND 12 GND

3 LFRAME 13 NC

4 No Pin 14 NC

5 LRESET 15 SB3V

6 NC 16 SERIRQ

7 LAD3 17 GND

8 LAD2 18 NC

9 VCC3 19 NC

10 LAD1 20 SUSCLK

11) F_USB1/F_USB2 (USB 2.0/1.1 Headers)

The header conforms to USB 2.0/1.1 specication. Each USB header can provide two USB ports via an

optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer.

Pin No. Denition Pin No. Denition

1 Power (5V) 6 USB DY+

2 Power (5V) 7 GND

3 USB DX- 8 GND

4 USB DY- 9 No Pin

5 USB DX+ 10 NC

Prior to installing the USB bracket, be sure to turn off your computer and unplug the power cord

from the power outlet to prevent damage to the USB bracket.

Pin No. Denition Pin No. Denition

1 VBUS 11 D2+

2 SSRX1- 12 D2-

3 SSRX1+ 13 GND

4 GND 14 SSTX2+

5 SSTX1- 15 SSTX2-

6 SSTX1+ 16 GND

7 GND 17 SSRX2+

8 D1- 18 SSRX2-

9 D1+ 19 VBUS

10 NC 20 No Pin

10) F_USB30 (USB 3.0/2.0 Header)

The header conforms to USB 3.0/2.0 specication and can provide two USB ports. For purchasing the

optional 3.5" front panel that provides two USB 3.0/2.0 ports, please contact the local dealer.

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3  

 S3 BSSS



U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

_ SF_

B 

USB0_B

B_

B_

F_USB3

 F_USB303



_



_3U

S_

_S

SS_F 

_

_ F 

_SB

20 1

DEBUG

PORT

G.QBOFM

- 16 -

13) BAT (Battery)

The battery provides power to keep the values (such as BIOS congurations, date, and time information)

in the CMOS when the computer is turned off. Replace the battery when the battery voltage drops to a low

level, or the CMOS values may not be accurate or may be lost.

You may clear the CMOS values by removing the battery:

1. Turn off your computer and unplug the power cord.

2. Gently remove the battery from the battery holder and wait for one minute. (Or use a

metal object like a screwdriver to touch the positive and negative terminals of the battery

holder, making them short for 5 seconds.)

3. Replace the battery.

4. Plug in the power cord and restart your computer.

•Always turn off your computer and unplug the power cord before replacing the battery.

•Replace the battery with an equivalent one. Damage to your devices may occur if the battery is

replaced with an incorrect model.

•Contact the place of purchase or local dealer if you are not able to replace the battery by yourself

or uncertain about the battery model.

•When installing the battery, note the orientation of the positive side (+) and the negative side (-)

of the battery (the positive side should face up).

•Used batteries must be handled in accordance with local environmental regulations.

- 17 -

Chapter 3 BIOS Setup

3-1 Startup Screen

The following startup Logo screen will appear when the computer boots.

Function Keys

•When the system is not stable as usual, select the Load Optimized Defaults item to set your system to its defaults.

•The BIOS Setup menus described in this chapter are for reference only and may differ by BIOS version.

On the main menu of the BIOS Setup program, press arrow keys to move among the items and press <Enter>

to accept or enter a sub-menu. Or you can use your mouse to select the item you want.

•Because BIOS ashing is potentially risky, if you do not encounter problems using the current version of BIOS,

it is recommended that you not ash the BIOS. To ash the BIOS, do it with caution. Inadequate BIOS ashing

may result in system malfunction.

•It is recommended that you not alter the default settings (unless you need to) to prevent system instability or other

unexpected results. Inadequately altering the settings may result in system's failure to boot. If this occurs, try to

clear the CMOS values and reset the board to default values. (Refer to the "Load Optimized Defaults" section in

this chapter or introductions of the battery/clear CMOS jumper in Chapter 2 for how to clear the CMOS values.)

BIOS (Basic Input and Output System) records hardware parameters of the system in the CMOS on the

motherboard. Its major functions include conducting the Power-On Self-Test (POST) during system startup,

saving system parameters and loading operating system, etc. BIOS includes a BIOS Setup program that allows

the user to modify basic system conguration settings or to activate certain system features.

When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS to

keep the conguration values in the CMOS.

To access the BIOS Setup program, press the <Delete> key during the POST when the power is turned on.

To upgrade the BIOS, use either the GIGABYTE Q-Flash or @BIOS utility.

•Q-Flash allows the user to quickly and easily upgrade or back up BIOS without entering the operating system.

•@BIOS is a Windows-based utility that searches and downloads the latest version of BIOS from the Internet

and updates the BIOS.

- 18 -

3-2 M.I.T.

This section provides information on the BIOS version, CPU base clock, CPU frequency, memory frequency,

total memory size, CPU temperature and CPU voltage, etc.

Whether the system will work stably with the overclock/overvoltage settings you made is dependent on your overall

system congurations. Incorrectly doing overclock/overvoltage may result in damage to CPU, chipset, or memory

and reduce the useful life of these components. This page is for advanced users only and we recommend you not to

alter the default settings to prevent system instability or other unexpected results. (Inadequately altering the settings

may result in system's failure to boot. If this occurs, clear the CMOS values and reset the board to default values.)

`M.I.T. Current Status

This screen provides information on CPU/memory frequencies/parameters.

`Advanced Frequency Settings

&Graphics Slice Ratio

Allows you to set the Graphics Slice Ratio.

&Graphics UnSlice Ratio

Allows you to set the Graphics UnSlice Ratio.

&CPU Clock Ratio

Allows you to alter the clock ratio for the installed CPU. The adjustable range is dependent on the CPU

being installed.

&CPU Frequency

Displays the current operating CPU frequency.

`Advanced CPU Core Settings

&CPU Clock Ratio, CPU Frequency

The settings above are synchronous to those under the same items on the Advanced Frequency Settings

menu.

- 19 -

(Note) This item is present only when you install a CPU that supports this feature. For more information about

Intel® CPUs' unique features, please visit Intel's website.

&Uncore Ratio

Allows you to set the CPU Uncore ratio. The adjustable range is dependent on the CPU being used.

&Uncore Frequency

Displays the current CPU Uncore frequency.

&CPU Flex Ratio Override

Enables or disables the CPU Flex Ratio. The maximum CPU clock ratio will be based on the CPU Flex

Ratio Settings value if CPU Clock Ratio is set to Auto. (Default: Disabled)

&CPU Flex Ratio Settings

Allows you to set the CPU Flex Ratio. The adjustable range may vary by CPU. (Default: 20)

&Intel(R) Turbo Boost Technology (Note)

Allows you to determine whether to enable the Intel® CPU Turbo Boost technology. Auto lets the BIOS

automatically congure this setting. (Default: Auto)

&Turbo Ratio (Note)

Allows you to set the CPU Turbo ratios for different number of active cores. Auto sets the CPU Turbo ratios

according to the CPU specications. (Default: Auto)

&Power Limit TDP (Watts) / Power Limit Time

Allows you to set the power limit for CPU Turbo mode and how long it takes to operate at the specied

power limit. If the specied value is exceeded, the CPU will automatically reduce the core frequency in

order to reduce the power. Auto sets the power limit according to the CPU specications. (Default: Auto)

&Core Current Limit (Amps)

Allows you to set a current limit for CPU Turbo mode. When the CPU current exceeds the specied current

limit, the CPU will automatically reduce the core frequency in order to reduce the current. Auto sets the

power limit according to the CPU specications. (Default: Auto)

&No. of CPU Cores Enabled (Note)

Allows you to select the number of CPU cores to enable in an Intel® multi-core CPU (the number of CPU

cores may vary by CPU). Auto lets the BIOS automatically congure this setting. (Default: Auto)

&Hyper-Threading Technology (Note)

Allows you to determine whether to enable multi-threading technology when using an Intel® CPU that

supports this function. This feature only works for operating systems that support multi-processor mode.

Auto lets the BIOS automatically congure this setting. (Default: Auto)

&CPU Enhanced Halt (C1E) (Note)

Enables or disables Intel

CPU Enhanced Halt (C1E) function, a CPU power-saving function in system halt

state. When enabled, the CPU core frequency and voltage will be reduced during system halt state to decrease

power consumption. Auto lets the BIOS automatically congure this setting. (Default: Auto)

&C3 State Support (Note)

Allows you to determine whether to let the CPU enter C3 mode in system halt state. When enabled, the

CPU core frequency and voltage will be reduced during system halt state to decrease power consumption.

The C3 state is a more enhanced power-saving state than C1. Auto lets the BIOS automatically congure

this setting. (Default: Auto)

&C6/C7 State Support (Note)

Allows you to determine whether to let the CPU enter C6/C7 mode in system halt state. When enabled, the

CPU core frequency and voltage will be reduced during system halt state to decrease power consumption.

The C6/C7 state is a more enhanced power-saving state than C3. Auto lets the BIOS automatically congure

this setting. (Default: Auto)

- 20 -

La pagina sta caricando ...

Gigabyte GA-H110M-H Manuale del proprietario

Marca: Gigabyte

Modello: GA-H110M-H

Tipo: Manuale del proprietario

Scarica il pdf

rapporto

in altre lingue

English: Gigabyte GA-H110M-H Owner's manual

Gigabyte GA-H110M-H Manuale del proprietario

Gigabyte GA-H110M-H Manuale del proprietario

in altre lingue

Documenti correlati