Hitachi VTFX140EUKN Operating Instructions Manual
- Categoria
- Lettori di cassette
- Tipo
- Operating Instructions Manual
Videorecorder
VTFX140EUKN
Operating instructions
The remote control
VTR/TV TV monitor: To switch between TV reception
and VCR playback
STANDBY m Switch on or off: Switching device on/off,
cancelling function, Cancelling programmed
recordings (TIMER)
0-9 Number buttons:0-9
SELECT Select: To select a function
CLEAR (CL) Delete: To delete last entry/Clear
programmed recording (TIMER)
REC/OTR n Record: To record the TV channel selected
on the video recorder. Press REC/OTR n
and A at the same time
A To activate recording
STILL R Still picture: To stop the tape and show a
still picture
INDEX E Index search: In combination with H /
I : to search for previous or next
recording on the cassette
G Playback: To play a cassette
H Rewind: During STOP and STANDBY:
rewind, during PLAYBACK: reverse scanning
I Forward wind: During STOP and STANDBY: forward wind, during
PLAYBACK: forward scanning
h Pause/Stop: To stop the tape, except during TIMER-recording
;P+ Select: To select the next line or programme number
Q Select: Cursor left
OK Store/Confirm: To store or confirm entry
P Select: Cursor right
MENU Menu: To call up or end main menu
P- = Select: To select the previous line or programme number
TIMER TIMER: To make a TIMER programming with VIDEO Plus+ or to alter or
clear a programmed TIMER
IN BRIEF
&
Front of the device
m Switch on or off: To switch off or on, interrupt a function, interrupt a programmed
recording (TIMER)
PROG r Select: One line or programme number down
PROG q Select: One line or programme number up
REC n Record: To record the TV channel selected at this moment
H Rewind: During STOP and STANDBY: rewind, during PLAYBACK: reverse
scanning
I Forward wind: During STOP and STANDBY: forward wind, during PLAYBACK:
forward scanning
G Playback: To play a cassette
h Pause/Stop, eject cassette: To stop the tape and eject the cassette
Back of the set
4 Mains socket: To connect the mains cable
AUDIO OUT L R Audio output socket, left/right: To connect a HiFi-set
EXT.2 AV. 2 Scart socket 2: To connect a satellite receiver, decoder, video recorder, etc.
(programme number '
E2')
EXT.1 AV. 1 Scart socket 1: To connect the TV set (programme number '
E1')
2 Aerial input socket: To connect the aerial cable
TV Aerial output socket: To connect the TV set
&
Thank you for buying a HITACHI video recorder. The
VT-FX140EUKN is one of the most sophisticated and
easy-to-use video recorders (VCR) on the market.
Please take the time to read this operating manual before
using your video recorder. It contains important information
and notes regarding operation.
The video recorder should not be turned on immediately
after transportation from a cold to a hot area or vice versa, or
in conditions of extreme humidity.
Wait at least three hours after transporting the device. The
video recorder needs this time in order to become acclimatised
to its new environment (temperature, air humidity, etc.).
This video recorder is used for the recording and playback of
VHS video cassettes.
Cassettes with the VHS-C label (VHS cassettes for
camcorders) may only be used with a suitable adapter.
We hope you enjoy your new video recorder
Important notes regarding operation
A Danger: High voltage!
Do not remove the top cover as there is a risk of an electrical
shock!
A The video recorder does not contain any components that can be
repaired by the customer. Please leave all maintenance work for
qualified personnel.
A As soon as the video recorder is connected to the power supply,
there are some components that are in constant operation. To
switch off the video recorder completely you must disconnect it
from the power supply.
C These operating instructions have been printed on non-polluting
paper.
C Deposit old batteries at the appropriate collection points.
C Please make use of the facilities available in your country for
disposing of the packaging of the video recorder in a way that
helps to protect the environment.
C This electronic device contains many materials that can be
recycled. Please enquire about the possibilities for recycling your
old device.
B Make sure that air can circulate freely through the ventilation
slots on the video recorder. Do not place the device on an
unsteady base.
B Make sure that no objects or liquids enter the video recorder. Do
not place vases or the like on the video recorder. If liquid is spilt
into it, immediately disconnect the video recorder from the power
supply and call After-sales Service for advice.
B Do not place any combustible objects on the device (candles,
etc.).
B Make sure that children do not place any foreign objects within
the openings or ventilation slots.
• VIDEO Plus+ and PlusCode are registered trademarks of
Gemstar Development Corporation. The VIDEO Plus+ system is
manufactured under licence from Gemstar Development
Corporation.
So that you can identify your machine for service questions or
in the event of theft, enter the serial number here. The serial
number (PROD.NO.) is printed on the type plate fixed at the
back of the device.
MODELNO. VT-FX140EUKN
PROD. NO. ............................
This product complies with the requirements of Directive
73/23/EEC +89/336/EEC +93/68 EEC.
Specifications
Voltage: 220-240V/50Hz
Energy consumption : 16W
Energy consumption (Standby): less than 4W (clock display
switched off)
Rewind time: approx. 100 seconds (cassette E-180)
Dimensions in cm (B/H/T): 38.0/9.3/26.0
Number of video heads :4
Number of video heads (HIFI):2
Recording/playback time: 4 hours (SP) (cassette E-240)
8 hours (LP) (cassette E-240)
Supplied accessories
• Operating instructions
• Remote control and batteries
• Antenna cable
• Power cable
• Quick install guide
OPERATING INSTRUCTIONS HITACHI VT-FX140EUKN
1
1. Connecting the video recorder 3..............
Important information for customers in Great Britain 3....
Preparing the remote control for operation 3...........
Connecting your video recorder to the TV set 3.........
Connecting with a scart cable and 'Easy Link' 4.........
Connecting with a scart cable without 'Easy Link' 5......
Connecting without a scart cable 6...................
Connecting additional devices 6.....................
2. Installing your video recorder 7...............
Initial installation 7...............................
Decoder allocation 7..............................
Manual TV channel search 8.......................
Using the satellite receiver 8.......................
Sorting TV channels automatically (Follow TV) 9........
Automatic TV channel search (Autoinstall) 10..........
Monitor function 10...............................
Sorting and clearing TV channels manually 10.........
Setting the time and date 11........................
3. Important notes for operation 12..............
Navigation in the screen menu 12...................
4. Playback 14...............................
Playing cassettes 14..............................
Playing back NTSC cassettes 14....................
Displaying current tape position 14...................
Searching for a tape position with picture
(scanning) 15...................................
Still picture / slow motion 15........................
Searching for tape position without picture (forward
wind and rewind) 15..............................
Easy View 15...................................
Tape Finder 16..................................
5. Eliminating picture interference 17............
Optimising tracking 17............................
Optimising still picture 17..........................
6. Manual recording 18........................
General information 18............................
Recording without automatic switch-off 18.............
Recording with automatic switch-off (OTR
One-Touch-Recording) 18.........................
Preventing accidental erasing of cassettes 18..........
Lining up recordings (assemble cut) 19...............
Selecting the recording speed (SP or LP) 19...........
Automatic controlled recording from a satellite
receiver (RECORD LINK) 20.......................
'Direct Record' 20................................
Switching 'Direct Record' on or off 21.................
7. Programming a recording (TIMER) 22..........
General information 22............................
Programming a recording (with 'VIDEO Plus+') 22.......
Problems and solutions for programmed recordings 23...
Programming a recording (without VIDEO Plus+) 24.....
Problem solving for programmed recordings 24.........
How to check, change or delete a programmed
recording (TIMER) 25.............................
'NexTView Link' 25...............................
8. Other functions 26.........................
Changing the video (colour) system 26...............
Child lock 26....................................
Switching the on-screen display (OSD) off or on 27......
Switch off the clock display 27......................
Continuous playback 28...........................
Automatic switch-off 28...........................
Selecting the sound channel 29.....................
9. Suppressing interference 30.................
Optimising the modulator 30........................
Switching the modulator on / off 30..................
10.Before you call an engineer 31...............
Table of contents
2
Important information for customers
in Great Britain
This set is fitted with an approved moulded 13 amp plug. To
change the fuse in this plug or to attach a different plug,
please proceed as follows:
1 Take off the fuse cover and remove the old fuse.
2 Insert a new fuse. Suitable fuses are those of the type BS
1362 3A, A.S.T.A. standard or BSI standard.
3 Close the fuse cover.
If the attached plug does not meet your requirements, you can
cut it off and replace it with a suitable plug. Please observe the
following conditions:
• If your new plug uses a built-in fuse, this should be a 3A
fuse.
• If your new plug does not contain a built-in fuse, please do
not use any fuses in your fusebox with a rating of more
than 5A.
• Please destroy the old, cut-off plug so that it cannot be
used elsewhere.
1 Connect the blue cable (neutral 'N') to the terminal in the
plug which is marked with the letter 'N' or coloured black.
2 Connect the brown cable (live, 'L') to the terminal in the
plug which is marked with the letter 'L' or coloured red.
3 Do not in any circumstances connect either of the two
cables to the terminal in the plug which is marked with the
letter 'E', the symbol "\" or coloured green or green /
yellow.
Before you refit the plug cover, make sure, that the grip at
the bottom of the plug is clamped over the plastic cover of
the lead, not just over the two wires.
Preparing the remote control for
operation
The remote control and its batteries are packed separately in
the original video recorder packaging. You must install the
batteries in the remote control before use - described in the
following section.
1 Take the remote control and the enclosed batteries (2
batteries).
2 Open the remote control's battery compartment and place
the batteries in it as shown in the picture and close the
battery compartment.
The remote control is now ready to use. Its range is
approximately 5 metres.
Connecting your video recorder to
the TV set
The necessary cable connections must be made before you
can record or playback TV programmes using your video
recorder.
We recommend that you use a scart cable to connect your TV
set and video recorder.
What is a scart cable?
The scart or Euro AV cable serves as the universal
connector for picture, sound and control signals. With this
type of connection, there is practically no loss of quality
during the picture or sound transfer.
When you install your video recorder for the first time, select
one of the following options:
'Connecting with a scart cable and Easy Link'
If your TV set is equipped with 'Easy Link, NexTView,
Megalogic, Datalogic,…' and you wish to use a scart cable.
What is Easy Link?
If your TV set is equipped with the following functions, e.g.
Easy Link, NextView, Megalogic, Datalogic,… which are
fully compatible with one another (TV set, video recorder,
etc.), your video recorder can exchange information with
your TV set. Please see your TV's operating instructions.
'Connecting with a scart cable without Easy Link'
If your TV set is not equipped with 'Easy Link, NexTView,
Megalogic, Datalogic,…' and you are using a scart cable.
'Connecting without a scart cable'
If you do not wish to use a scart cable.
1. Connecting the video recorder
3
Connecting with a scart cable and
'Easy Link'
Your video recorder can exchange information with your TV
set using 'Easy Link'. Furthermore, your TV channels can be
transferred in the same order from your TV set to your video
recorder using 'Easy Link'.
Have the following cables ready:
an aerial cable (1, supplied), a mains cable (2, supplied), a
special scart cable (for Easylink) (3).
1 Switch off your TV set.
2 Remove the aerial cable plug from your TV set. Insert it
into the socket
2 at the back of the video recorder.
3 Insert one end of the supplied aerial cable into the socket
TV at the back of the video recorder and the other end
into the aerial input socket at the back of the TV set.
4 Plug in a special scart cable (for Easylink) into the scart
socket
EXT.1 AV. 1 at the back of the video recorder
and the scart socket on the TV set reserved for the video
recorder operation (see TV set operating instructions).
My TV set has several scart sockets. Which one should
I use?
Please see the operating instructions of your TV set to find
out which socket supports 'Easy Link'.
5 Switch on the TV set.
6 Insert one end of the supplied mains cable into the mains
socket
4 at the back of the video recorder and the
other end into the wall socket.
7 A message appears on the screen announcing that the
transfer has started.
The TV set transfers all saved TV channels, in the same
order, to the video recorder.
This may take several minutes.
When all the information has been transferred, the
following appears on the TV screen: 'YEAR', 'MONTH',
'DATE', 'TIME'.
CLOCK
YEAR è 2001 p
MONTH 01
DATE 01
TIME 20:00
SMART CLOCK ON
________________________________
EXITpMENU STOREpOK
8 Check the year in line 'YEAR'. If required, please change
the year with the number buttons
0-9 on the remote
control.
9 Select the next line using
;P+ or P- = .
0 Check 'MONTH', 'DATE', 'TIME' and if required modify in
the same way.
A When all information is correct, confirm with
OK .
The initial installation is now complete.
4
Connecting with a scart cable
without 'Easy Link'
Have the following cables ready:
an aerial cable (1, supplied), a mains cable (2, supplied), a
scart cable (3).
1 Remove the aerial cable plug from your TV set. Insert it
into the socket
2 at the back of the video recorder.
2 Insert one end of the supplied aerial cable into the socket
TV at the back of the video recorder and the other end
into the aerial input socket at the back of the TV set.
3 Plug one end of a scart cable into the scart socket
EXT.1 AV. 1 at the back of the video recorder and the
other end into the suitable scart socket on your TV set
reserved for the video recorder operation (see your TV's
operating instructions).
My TV set has several scart sockets. Which one should
I use?
Select that scart socket which is suited for the video output
as well as for the video input.
My TV offers me a selection menu for the scart socket.
Select 'TV' as a connection source of this scart socket.
4 Switch on the TV set.
5 Insert one end of the supplied mains cable into the mains
socket
4 at the back of the video recorder and the
other end into the wall socket.
6 If the connection was properly made and your TV was
automatically switched to the programme number for
the scart socket, e.g. 'EXT', '0', 'AV', you will see the
following picture:
CONGRATULATIONS
YOU NOW OWN A NEW
VIDEO RECORDER
CONTINUEpOK
My screen is empty
* Many TV sets are switched to the programme number for
the scart socket by way of a control signal sent through the
scart cable.
* If the TV set does not automatically switch to the scart
socket programme number, manually change to the
corresponding programme number on your TV set (see your
TV's operating instructions).
Then, read the paragraph 'Initial installation' in the chapter
'Installing your video recorder'.
5
Connecting without a scart cable
Have the following cables ready:
an aerial cable (1, supplied), a mains cable (2, supplied).
1 Switch off your TV set.
2 Remove the aerial cable plug from the aerial input socket
of the TV set. Insert it into the socket
2 at the back of
the video recorder.
3 Insert one end of the supplied aerial cable into the socket
TV at the back of the video recorder and the other end
into the aerial input socket at the back of the TV set.
4 Insert one end of the supplied mains cable into the mains
socket
4 at the back of the video recorder and the
other end into the wall socket.
5 Switch on your TV set and select the programme number
used for video playback on your TV set (see your TV's
operating instructions).
Which programme number is used for video recorder
operation?
To ensure the stability of the television picture during
cassette playback (prevention of waves or streaks), special
programme numbers have been set aside on the TV for the
use of video recorders. This is usually the highest possible
programme number, e.g. '12', '16', '99' or even programme
number '0'. For more information, please see your TV's
operating instructions.
Important: For a Hitachi TV use programme 0
6 Select this programme number and manually start the
TV's channel search as if you wanted to save a new TV
channel until the 'test image' appears.
I do not see a 'test screen'
* Check the cable connections.
* The video recorder 'transmits' on the 583MHz frequency
(channel 35)
Repeat the channel search on your TV set.
7 Save this programme number setting on your TV set for
video recorder operation.
Programme number for video recorder operation
You have now saved a programme number for use by your
video recorder as you would a regular TV channel. This
programme number must now be used in future for video
recorder playback ('video recorder' TV channel).
You can find more details in chapter 'Initial Installation'.
Connecting additional devices
You can connect additional devices such as decoders, satellite
receivers, camcorders, etc. to the socket
EXT.2 AV. 2 .
Two audio sockets
AUDIO OUT L R are located on the back of
the video recorder (audio signal output left/right). These can be
used to connect stereo systems.
6
Initial installation
This chapter shows you how to start the initial installation. The
video recorder automatically seeks out and stores all available
TV channels.
'Aim' correctly
In the following sections, you require the remote control for
the first time. When using, always aim the front of the
remote control at the video recorder and not at the TV set.
Connecting additional devices
After you have connected additional devices (satellite
receiver, etc.) through the aerial cable, switch them on. The
automatic channel search will recognise them and save
them.
1 Confirm the image on the TV screen by pressing the
OK button on the remote control.
Autoinstall starts. This picture will appear on the screen:
AUTO INSTALL
SEARCHING
00 TV CHANNELS FOUND
ƒƒƒƒƒƒƒ__________________
PLEASE WAIT...
The video recorder does not find any TV channels
during the search
* Select channel 1 on the TV set. Can you see the saved TV
channel on the TV set?
If not, check the cable connection of the aerial (aerial
socket), video recorder, TV set.
* Please have patience.
The video recorder searches the entire frequency range in
order to find and save the largest possible number of TV
channels. It is possible that the TV channels in your country
are broadcast in a higher frequency range. As soon as this
range is reached during the search, the video recorder will
find the TV channels.
2 When 'Autoinstall' is complete, 'STORED' will briefly
appear on the TV screen.
The initial installation is now complete.
Check the date and time. Please read 'Setting the time and
date' in this chapter.
Satellite receiver
If you are connecting a satellite receiver, please read the
section 'Using the satellite receiver'.
Decoder
If you are connecting a decoder, you must install it as
described in the next section.
Decoder allocation
Some TV channels transmit encoded TV signals which can
only be viewed with a commercially purchased or hired
decoder without disturbances. You can connect such a
decoder (descrambler) to this video recorder. The following
function will automatically activate the connected decoder for
the desired TV channel.
How do I allocate the decoder with Easy Link?
If your TV supports the 'Easy Link' function, the decoder
must be allocated to the respective TV channel on the TV
(see TV operating instructions).
1 Switch the TV on. If applicable, select the programme
number for the video recorder operation.
2 Use the buttons
;P+ , P- = on the video recorder or
the number buttons
0-9 on the remote control to select
the TV channel which you would like to allocate the
decoder to.
3 Press the button
MENU on the remote control. The main
menu will appear.
4 Use the buttons
;P+ or P- = to select the line
'MANUAL SEARCH' and confirm with
OK .
MANUAL SEARCH
PROGRAMME NUMBER è P01 p
S-CHANNEL NO
CHANNEL NUMBER 21
DECODER OFF
TV SYSTEM AUTO
________________________________
EXITpMENU STOREpOK
5 Use the buttons P- = or ;P+ to select the line
'DECODER'.
6 Use the buttons
Q or P to select 'ON' (Decoder
switched on).
2. Installing your video recorder
7
How can I switch off the decoder?
Use the button
P on the screen to select 'OFF' (Decoder
switched off).
7 Confirm with
OK .
8 End with the button
MENU .
BBC1
The decoder has now been allocated to this TV channel.
If this TV channel is chosen, the symbol 'DEC' will appear in the
video recorder display.
Manual TV channel search
In some cases it could occur that all of the TV channels were
not found and saved during the initial installation. In this case,
the missing or coded TV channels must be searched for and
stored manually.
Manual search with EasyLink
With 'Easy Link', the saved TV channels will automatically
be loaded from the TV. As soon as the 'Manual TV channel
search' function is carried out, the automatic information
transfer from the TV will start. To save new TV channels,
they must first be saved on the TV.
1 Switch on the TV set. If required, select the programme
number for the video recorder.
2 Press
MENU on the remote control.
The main menu will appear.
3 Select line 'MANUAL SEARCH' using
P- = or ;P+ and
confirm with
OK .
MANUAL SEARCH
PROGRAMME NUMBER è P01 p
S-CHANNEL NO
CHANNEL NUMBER 21
DECODER OFF
TV SYSTEM AUTO
________________________________
EXITpMENU STOREpOK
4 Select line 'PROGRAMME NUMBER' using P- = or
;P+ .
5 Using
Q or P , select the desired programme
number that you want to use for the TV channel, e.g.
'P01'.
6 In line 'S-CHANNEL', select the desired display using
P .
What is hidden behind the settings?
'NO': Display/Entry of channels
'YES': Display/Entry of special channels
What is a special channel?
TV channels are transmitted in certain pre-defined
frequency ranges. These ranges are divided into channels.
A specific frequency/channel is assigned to each TV station.
Certain frequency ranges are specified as special channels
(hyperband channels).
7 In line 'CHANNEL NUMBER', enter the channel of the
desired TV station using the number buttons
0-9 .
I don't know the channels for my TV stations
* In this case, press
P in line 'CHANNEL NUMBER'to
start the automatic channel search. A changing channel
number will appear on the TV screen.
Continue the automatic search until you have found the
desired TV channel.
What is NICAM?
NICAM is a digital sound transmission system. Using
NICAM, you can transmit either 1 stereo channel or 2
separate mono channels. However, if you experience poor
reception resulting in sound disruptions, you can turn off
NICAM.
In line 'NICAM', select 'OFF' using
Q or P .
8 Save the TV channel with
OK .'STORED' will briefly
appear on the TV screen.
9 To search for other TV channels, begin again at step 3.
0 To end, press MENU .
Using the satellite receiver
TV channels from a satellite receiver (connected to the scart
socket
EXT.2 AV. 2 ) are received on the video recorder on
programme number 'E2'.
To do this, select programme number 'E1' with
0 on the
remote control and then select programme number 'E2' with
P- = .
You should select the TV channels to be received by the
satellite receiver directly on the receiver itself.
8
Sorting TV channels automatically
(Follow TV)
When the automatic channel search function is activated, the
TV channels are saved in a specific order. This may vary from
the order of TV channels on the TV set.
This only works if the video recorder (socket
EXT.1 AV. 1 )
and the TV set are connected with a scart cable.
What does EASYLINK do?
If your TV set supports 'Easylink,...', TV channels will be
saved during the initial installation in the same order as they
appear on the TV set. To save the TV channels in a
different order, you must change the order on the TV set.
When you start Follow TV, the information then is
re-transferred from the TV set.
1 Switch on the TV set. If required, select the programme
number for the video recorder.
2 Press the
MENU button on the remote control. The main
menu will appear.
MENU
CLOCK
AUTO INSTALL
MANUAL SEARCH
FOLLOW TV
TV CHANNEL ALLOC.
RECORD SPEED
AUTO STANDBY
VIDEOSYSTEM
SPECIAL SETTINGS
________________________________
…EXITpMENU OK
†
3 Select line 'FOLLOW TV' using P- = or ;P+ and
confirm with
OK .
4 Press the
OK button. 'TV01' will appear in the video
recorder display.
TV01
5 Select programme number '1' on the TV set.
I cannot switch my TV set to programme number '1'
* If you have connected additional devices to socket
EXT.2 AV. 2 , please disconnect these devices. Because of
other connected devices, the TV set could switch to the
programme number of the scart socket.
6 Confirm with
OK on the video recorder remote control.
The video recorder compares the TV channels on the TV
set and the video recorder.
If the video recorder finds the same TV channel as on the
TV set, then it stores it at 'P01'.
'NOTV' will appear in the display. The video recorder is
not receiving a video signal from the TV set.
* Check the plug on the scart cable.
* Check your TV's operating instructions to see which scart
socket is used for video signals.
* If this does not help, it's not possible to use this function.
Please read the section 'Sorting TV channels manually'.
7 Wait until the next number, e.g. 'TV02' appears in the
display.
8 Select the next programme number on the TV set, e.g.
'2'.
9 Confirm with
OK on the video recorder remote control.
Deleting sorting
You can delete an incorrect TV channel sorting by pressing
CLEAR (CL) .
0 Repeat steps 7to 9until you have assigned a
programme number to all TV channels.
A To end, press
MENU .
I cannot switch my TV set to programme number '1'
* If you have connected additional devices to socket
EXT.2 AV. 2 , please disconnect these devices. Because of
other connected devices, the TV set could switch to the
programme number of the scart socket.
9
Automatic TV channel search
(Autoinstall)
During installation, all available TV channels are searched for
and saved. If the channel assignments of your cable or
satellite TV provider change or if you are reinstalling the video
recorder, e.g. after moving house, you can start this procedure
again. This will replace the TV channels already saved with the
new ones.
What does Easy Link do?
With Easylink, TV channels can only be searched for and
saved on the TV set. These settings are accepted by the
video recorder. Therefore, this function starts the transfer of
TV channels from the TV set.
1 Switch on the TV set. If required, select the programme
number for the video recorder.
2 Press the
MENU button on the remote control. The main
menu will appear.
3 Select line 'AUTO INSTALL' using
P- = or ;P+ .
4 Press
OK .
AUTO INSTALL
SEARCHING
00 TV CHANNELS FOUND
ƒƒƒƒƒƒƒ__________________
PLEASE WAIT...
5 'Autoinstall' starts. Wait until all TV channels have been
found. This can take several minutes.
6 When Autoinstall is complete, 'STORED' will briefly appear
on the TV screen.
Date and time have been set and saved.
7 To end, press
MENU .
You can read about how to search for a TV channel manually
in the section 'Manual TV channel search'.
Monitor function
You can switch back and forth between the TV picture and
video recorder picture with
VTR/TV . But this only works
when you use a scart cable to connect the video recorder to
your TV set and your TV set responds to this switch-over.
Sorting and clearing TV channels
manually
After you have performed the automatic channel search you
may not agree with the sequence in which the individual TV
channels have been allocated to the programme positions
(programme numbers) of the video recorder. You can use this
function to individually sort the TV channels already saved or
to delete unwanted TV channels or those with poor reception.
The Teletext clock resets automatically
If you save a TV channel which transmits TXT/PDC on
programme number 'P01', date and time will automatically
be transmitted and constantly updated. As a result, time
changes, i.e. daylight savings time, will be set automatically.
What does Easy Link do?
With Easylink, TV channels can only be searched for and
saved on the TV set. They will then be transferred to the
video recorder.
This function will start the automatic information transfer.
1 Switch on the TV set. If required, select the programme
number for the video recorder.
2 Press
MENU on the remote control. The main menu will
appear.
3 Select line 'TV CHANNEL ALLOC.' using
P- = or
;P+ .
4 Confirm with
OK .
TV CHANNEL ALLOC.
ALLOCATE ON P01
TV CHANNEL è BBC1 p
________________________________
ALLOCATEpOK EXITpMENU
5 Using Q or P , select the saved TV channel that
you want to assign to the programme number 'P01'.
10
6 Confirm with OK . The following message will briefly
appear on the TV screen: 'ALLOCATED ON P01'.
7 Then the sorting for the next highest programme number
will appear on the screen, e.g. 'ALLOCATE ON P02'.
8 Using
Q or P , select the saved TV channel that
you want to assign to this programme number, e.g. 'P02'.
Deleting TV channels
Using
CLEAR (CL) you can delete unwanted TV channels
or those with poor reception.
9 Confirm with
OK . The following message will briefly
appear on the TV screen: 'STORED'.
The main menu will appear on the screen
* After you have confirmed the last channel that can be
sorted, you will automatically return to the main menu since
no more TV channels can be assigned.
0 To assign other TV channels to a programme number,
repeat steps 7to 9.
A Confirm the assignment of the TV channel with
MENU .
B To exit the main menu, press
MENU .
Setting the time and date
If the display shows an incorrect time or '--:--', the time and
date must be reset manually.
If a TV channel which transmits TXT/PDC (teletext/PDC) is
stored under programme number 'P01', time/date will
automatically be taken from the TXT/PDC information.
(SMART CLOCK)
1 Switch on the TV set. If required, select the programme
number for the video recorder.
2 Press
MENU on the remote control. The main menu will
appear.
3 Select line 'CLOCK' using
P- = or ;P+ and confirm
with
OK .
CLOCK
YEAR è 2001 p
MONTH 01
DATE 01
TIME 20:00
SMART CLOCK ON
________________________________
EXITpMENU STOREpOK
4 Check the year in line 'YEAR'. If required, please change
the year with the number buttons
0-9 on the remote
control.
5 Select the next line with
;P+ or P- = .
6 Check 'MONTH', 'DATE' and 'TIME' in the same way.
Time/date is displayed incorrectly despite manual
setting
* With Smart Clock, time/date is transferred from the TV
channel saved on 'P01' and automatically corrected.
Switch off Smart Clock. In line 'SMART CLOCK', select 'OFF'
using
Q or P .
You can switch on 'SMART CLOCK' again when you select
'ON'.
7 Check the displayed settings and confirm with
OK .
'STORED' will appear briefly on the screen.
8 To end, press
MENU .
11
Switching on
You can switch on the video recorder with the
STANDBY m button, the number buttons 0-9 or by
putting in a cassette.
Automatic switch-off
If the video recorder is not used for several minutes, it
switches itself off automatically. This function can be
deactivated (e.g. if you want to use the video recorder as a
TV receiver). For more information, please read the section
'Automatic switch-off' in chapter 'Additional functions'.
Time in the display
If you have switched the video recorder off with
STANDBY m , the time will show in the display, e.g.
'18:00'.
If the clock has not been set, '--:--' will appear.
When the video recorder is switched off and the time isn't
shown in the video recorder display, the clock display may
be switched off. You will find more information in the chapter
'Additional functions' section 'Switch off the clock display'.
Energy consumption
The video recorder should always be connected to the
mains so as not to affect the use of the TV or programmed
recordings.
Your video recorder uses less than 4W (with clock display
switched off).
Power outage/no power
Channel information remains saved for up to 1 year, the
time and timer information is saved for up to 3 hours.
Emergency exit
The video recorder and the remote control have the option
of an 'Emergency exit'. You can use the
STANDBY m
button to interrupt any function or step during use.
You can operate your device without worry. There is no risk
whatsoever of damaging the video recorder by performing
user steps incorrectly.
Navigation in the screen menu
You can check/change many functions and settings of your
video recorder via the screen menu. The individual functions
are selected as follows:
MENU
CLOCK
AUTO INSTALL
MANUAL SEARCH
FOLLOW TV
TV CHANNEL ALLOC.
RECORD SPEED
AUTO STANDBY
VIDEOSYSTEM
SPECIAL SETTINGS
________________________________
…EXITpMENU OK
†
Call up the menu: with MENU .
To select: with
P- = or ;P+ .
To enter or change your selection: with the number buttons
0-9 or with Q or P .
To save or confirm: with
OK .
To cancel: with
STANDBY m .
To end: with
MENU .
3. Important notes for operation
12
The symbols on your video recorder
display
These symbols can light up on your video recorder display:
This is where the current operating mode is
shown as a symbol.
LP When you have switched on the LP (Long Play)
function or when you play a tape that has been
recorded in LP (Long Play).
When you have switched on the child lock.
When a satellite recording has been
programmed.
DEC When a decoder has been allocated to the TV
channel (currently selected programme number
on the video recorder) you have currently
selected on the video recorder.
When you play a cassette that has been
recorded with hifi sound, or when a hifi sound is
transmitted.
When you are making a recording.
k When you have programmed a recording or
when a programmed recording is being made.
D When you are programming daily recordings.
W When you are programming weekly recordings.
When you have put a cassette in the video
recorder.
DATE When the date of the programmed recording is
shown.
START When the start time of the programmed
recording is shown.
PROG. When the programme number of the
programmed recording is shown.
END When the end time of the programmed recording
is shown.
VPS/PDC Video Programming System / Programme
Delivery Control: when a VPS or PDC code is
being transmitted.
Display of programme number of the TV channel
/ tape position / channel name / function.
Tape position in seconds.
13
Playing cassettes
You can use this video recorder to play back recorded VHS
video cassettes. You can operate the video recorder using the
remote control or the buttons on the front of the video recorder.
What does VHS mean?
'Video Home System' (VHS) has become the world-wide
standard for the playback and recording of amateur video
cassettes. This popular standard continues to be improved.
Super VHS (S-VHS) provides a sharper picture and less
noise. Digital VHS (D-VHS) works with digital picture and
sound signals. Your video recorder can only record and play
standard VHS cassettes.
1 Put a cassette into the cassette slot.
The cassette is inserted automatically. '
v' will appear on
the display.
2 Press the Play button
G to view the tape.
This will, for example, appear in the display:
0:00:02
Picture/ sound quality is poor
* When playing rental videos or older, poorer quality
cassettes, it may not be possible to completely filter out
picture and sound interference. This is not a fault in your
machine.
Read the chapter 'Eliminating picture interference'.
* During playback the automatic TV system will switch-over
automatically. If picture/sound interference occurs, attempt
to fix the problem by manually switching the TV system. In
that case, turn to chapter 'Additional functions' section
'Switching the video (color) system'.
3 To stop the playback, press
h on the remote control or
h on the video recorder.
4 To eject the cassette, press
J on the video recorder
when the video recorder stops the playback (STOP).
Automatic switch-off of special functions
Many functions (e.g. pause, still picture, search) switch
themselves off automatically after a short time in order to
protect the cassette and to save energy.
Do I need to change the playback speed when playing
back LP recordings?
For playback, the correct recording speed 'SP' will
automatically be selected. For more information, please
read the section 'Selecting the recording speed (SP/LP)' in
the chapter 'Manual recording'.
Playing back NTSC cassettes
Cassettes that have been recorded in the NTSC standard (for
example, American cassettes) can be played back using this
video recorder. However, this only works on PAL-television
sets which are suitable for a picture frequency of 60Hz.
When you play an NTSC cassette '60HZ' will appear on the
display.
Some special features (for example, still picture) are not
possible while you are playing an NTSC cassette.
Displaying current tape position
The display shows the tape position in hours, minutes and
seconds. In addition, by pressing
OK you can show the
present tape position on the TV screen.
The following information is displayed on the screen:
e.g.: 0:02:45 Shows the tape position in hours, minutes and
seconds.
Moving/blinking arrow: This indicates the current tape position.
The arrow moves in a line from left (tape start) to right (tape
end).
'REMAIN 0:06': will show the actual amount of
playing/recording time left on the tape in hours and minutes.
When you play an NTSC cassette, the video recorder will not
show 'REMAIN 0:06'.
How can I set the counter to '0:00:00'?
You can set the counter to '0:00:00' using
CLEAR (CL) .
When you put a cassette in the machine, the counter will
automatically reset to 0:00:00'.
The counter does not move
* This occurs when there are no recordings on a portion of a
tape. Therefore, the video recorder cannot receive any
information from the tape. This is not a fault in your
machine.
The display/the screen shows '-0:01:20'
* If you rewind a cassette from the tape position '0:00:00',
the counter will show for instance, '-0:01:20' (the cassette
4. Playback
14
will be rewound to 1 minute and 20 seconds before
'0:00:00').
'-:--' is displayed in the 'REMAIN' counter
* This counter will automatically recognise the length of the
tape. In addition, when you put in a cassette the video
recorder must first calculate the time played. Therefore, '-:--'
appears first and only after the tape has been running for a
few seconds will the correct playing time be shown.
Searching for a tape position with
picture (scanning)
1 While a cassette is playing, press H (reverse) or
I (forward) one or more times. This will, for example,
appear in the display:
0:30:21
2 To stop at a certain place on the tape, press G .
Decreased picture quality
Scanning interferes with the picture quality. The sound is
switched off. This is not a fault in your machine.
Still picture / slow motion
1 During playback, press STILL R to stop the tape and
display a still picture. This will, for example, appear in the
display:
0:00:02
2 Each time you press STILL R , the picture will
advance one frame.
3 When you hold down the
STILL R button, the tape
will be played in slow motion.
4 When you press
I several times, you have a choice
of several playback speeds for slow motion.
5 To continue playback, press
G .
Searching for tape position without
picture (forward wind and rewind)
1 Stop the tape with h .
2 Press
H (reverse) or I (forward). This will, for
example, appear in the display:
0:30:21
3 To stop at a certain place on the tape, press h .
Easy View
With this function you can switch to picture search during wind
and rewind.
1 If you hold
H (rewind) or I (wind) during wind or
rewind, you will switch to picture search.
2 As soon as you release the button, the video recorder will
automatically switch back to rewind or wind.
15
Tape Finder
Automatic search for a tape position
(index search)
Every time a tape is recorded an index marking is written on
the tape. This marking can be compared with a bookmark.
These marked positions can be found again quickly and easily
later by pressing a button.
1 To search for the previous marking, press
INDEX E and
then
H .
2 For the next marking, press
INDEX E and then I .
This will, for example, appear in the display for the next
marking.
0:30:02
3 As soon as the video recorder finds this marking, it
automatically switches to playback.
Automatic search for a blank space
on the tape
You can search for space on the tape (at least 1 minute of
blank tape) for a new recording, for example, after an existing
recording on the tape.
1 Press
INDEX E . Then press h . This will, for
example, appear in the display:
0:00:00
2 As soon as the video recorder finds the corresponding
tape position, it automatically switches to pause.
The cassette is ejected
* The video recorder was unable to find any blank space on
the tape inserted.
Automatic commercial skip
Do you get annoyed with the commercial breaks that are
recorded along with your programmes? This function allows
you to quickly and easily skip over them. By pressing a button,
the video recorder winds the tape forward for about 2 minutes
and then automatically switches to playback again.
1 During playback, press
G .
2 The video recorder winds the tape forward by
approximately 2 minutes of play time.
Repeating/cancelling 'Commercial Skip'
If the commercial is still on, you can restart the function.
If the commercial break ends sooner, simply press
G .
The video recorder immediately switches to playback.
16
Optimising tracking
This video recorder has an automatic tracking function. In
order for the video heads to optimally read the video track of
the newly inserted video cassette, the tape speed is slightly
corrected automatically.
In some cases however, interference will still occur.
The following section will explain how to manually adjust the
tracking settings.
1 While a cassette is playing, hold
;P+ until 'TRAC'
(TRACking) appears in the display.
2 Hold down the buttons
;P+ or P- = until the playback
quality is at its best.
3 Wait a few seconds, until 'TRAC' disappears from the
display.
These selected picture settings will not change until you eject
the cassette.
Optimising still picture
If the still picture vibrates vertically, you can improve the still
picture as follows:
1 During still picture, hold
;P+ or P- = until the picture
quality is at its best.
'JITT' will appear in the display.
2 When you release the button, 'JITT' will disappear.
The video recorder will store these settings automatically.
I cannot reach optimal quality for the still picture
* Interference which cannot be alleviated by this function
can occur in cassettes of poor quality or camcorder
cassettes .
5. Eliminating picture interference
17
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
Hitachi VTFX140EUKN Operating Instructions Manual
- Categoria
- Lettori di cassette
- Tipo
- Operating Instructions Manual
in altre lingue
- English: Hitachi VTFX140EUKN
Documenti correlati
Altri documenti
-
Yamaha DRX-2 Manuale del proprietario
-
Creative ZEN X-FI - 2 Manuale utente
-
Philips 25PV707 Manuale utente
-
-
Panasonic nv f 55 eg Manuale del proprietario
-
Philips TV Manuale utente
-
-
-
Sanyo vhr 274 Manuale del proprietario