Stanley SFMCCS730B Manuale utente

Categoria
Motoseghe a batteria
Tipo
Manuale utente

Questo manuale è adatto anche per

www.stanley.gb
3
6112 7
13 2 12 15
11
10
9
1
14
17
16
5 4
8
SFMCCS730
2
English (original instructions) 7
Deutsch (übersetzt von den originalanweisungen) 20
Français (traduction de la notice d’instructions originale) 34
Italiano (tradotto dalle istruzioni originali) 48
Nederlands (vertaald vanuit de originele instructies) 63
Español (traducido de las instrucciones originales) 77
Português (traduzido das instruções originais) 91
Svenska (översatt från de ursprungliga instruktionerna) 106
Norsk (oversatt fra de originale instruksjonene) 117
Dansk (oversat fra original brugsvejledning) 129
Suomi (käännetty alkuperäisestä käyttöohjeesta) 141
Ελληνικά (μετάφραση από τις πρωτότυπες οδηγίες) 153
3
14
18
18b
18a
15
14
14 14a
D
8
7
21 45
6
A B
C D
5 4
6
2119
20
E4 5
3mm
F
4
G H
10 9
I
11 4
J
12
13
K
3
13
L
5
2
1
M
60°
22
N
(0.635mm)
O P
17
16
Q
23
R
6
S
Retreat
Retreat
Tree
45º
45º
Direction of fall
T
51mm
Direction of fall
Notch
Felling back cut
51mm
Hinge
U V
W X
7
Y
1
2
Y
YZ
Intended use
Your STANLEY FATMAX, SFMCCS730 Compact Chainsaw
has been designed for light duty cutting and pruning. This
appliance is intended for professional and private, non
professional users.
Safety instructions
General power tool safety warnings
Warning! Read all safety warnings,
instructions, illustrations and specications
provided with power tool. Failure to follow all
instructions listed below may result in electric
shock, re and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below refers
to your mains operated (corded) power tool or battery oper-
ated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of ammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodied plugs
and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the inuence
of drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal
injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as a dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
c. Prevent unintentional starting.
8
ENGLISH (Original instructions)
Ensure the switch is in the off-position before
connecting to power source and/or battery pack,
picking up or carrying the tool. Carrying power tools
with your nger on the switch or energising power tools
that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
h. Do not let familiarity gained from frequent use of tools
allow you to become complacent and ignore tool
safety principles. A careless action can cause severe
injury within a fraction of a second.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
h. Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
5. Battery tool use and care
a. Recharge only with the charger specied by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of re when used with
another battery pack.
b. Use power tools only with specically designated
battery packs. Use of any other battery packs may create
a risk of injury and re.
c. When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws, or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
or a re.
d. Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, ush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
e. Do not use a battery pack or tool that is damaged or
modied. Damaged or modied batteries may exhibit
unpredictable behaviour resulting in re, explosion or risk
of injury.
f. Do not expose a battery pack or tool to re or
excessive temperature. Exposure to re or temperature
above 130 °C may cause explosion. NOTE: The
temperature „130 °C“ can be replaced by the temperature
„265 °F“.
g. Follow all charging instructions and do not charge the
battery pack or tool outside the temperature range
specied in the instructions. Charging improperly or at
temperatures outside the specied range may damage the
battery and increase the risk of re.
6. Service
a. Have your power tool serviced by a qualied repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
b. Never service damaged battery packs. Service of
battery packs should only be performed by the
manufacturer or authorized service providers (only used
for battery tools).
9
ENGLISH
(Original instructions)
General chain saw safety warnings
Warning! Additional safety warnings for
chainsaws
uKeep all parts of the body away from the saw chain
when the chainsaw is operating. Before you start the
chainsaw, make sure the saw chain is not contacting
anything. A moment of inattention while operating chain
saws may cause entanglement of your clothing or body
with the chain saw.
uAlways hold the chainsaw with your right hand on the
rear handle and your left hand on the front handle.
Holding the chainsaw with a reversed hand conguration
increases the risk of personal injury and should never be
done.
uHold the chain saw by insulated gripping surfaces
only, because the saw chain may contact hidden
wiring. Saw chains contacting a "live" wire may make
exposed metal parts of the chain saw "live'" and could give
the operator an electric shock.
uWear eye protection. Further protective equipment for
hearing, head, hands, legs and feet is recommended.
Adequate protective equipment will reduce personal injury
from ying debris or accidental contact with the saw chain.
uDo not operate a chain saw in a tree, on a ladder, from
a rooftop, or any unstable support. Operation of a chain
saw in this manner could result in serious personal injury.
uAlways keep proper footing and operate the chain saw
only when standing on xed, secure and level surface.
Slippery or unstable surfaces such as ladders may cause
a loss of balance or control of the chainsaw.
uWhen cutting a limb that is under tension be alert
for spring back. When the tension in the wood bres is
released the spring loaded limb may strike the operator
and/or throw the chain saw out of control.
uUse extreme caution when cutting brush and saplings.
The slender material may catch the saw chain and be
whipped toward you or pull you off balance.
uCarry the chain saw by the front handle with the chain
saw switched off and away from your body. When
transporting or storing the chainsaw always t the
guide bar cover. Proper handling of the chain saw will
reduce the likelihood of accidental contact with the moving
saw chain.
uFollow instructions for lubricating, chain tensioning
and changing accessories. Improperly tensioned or
lubricated chain may either break or increase the chance
for kickback
uCut wood only. Do not use chainsaw for purposes not
intended. For example: do not use the chainsaw for
cutting plastic, masonry or non-wood building materi-
als.
Use of the chainsaw for operations different than intended
could result in a hazardous situation.
uDo not attempt to fell a tree until you have an
understanding of the risks and how to avoid them.
Serious injury could occur to the operator or bystanders
while felling a tree.
uFollow all instructions when clearing jammed mate-
rial, storing or servicing the chain saw. Make sure the
switch is off and the battery pack is removed. Unex-
pected actuation of the chain saw while clearing jammed
material or servicing may result in serious personal injury.
Additional power tool safety warnings
Warning! Additional safety warnings for co
pact chainsaws.
The intended use is described in this instruction manual. Do
not use the tool for purposes not intended; for example do not
use the tool to fell trees. The use of any accessory or attach-
ment or performance of any operation with this tool other than
those recommended in this instruction manual may present a
risk of personal injury.
uWear close tting and protective clothing including
a safety helmet with visor/goggles, ear protectors,
non- skid safety footwear, protective bib trousers and
strong leather gloves.
uAlways position yourself out of the path of falling
branches.
uThe safe distance between a branch to be felled and
bystanders, buildings and other objects is at least
2 1/2 times the length of the branch. Any bystander,
building or object within this distance is at risk from being
struck by the falling branch.
uPre-plan a safe exit from falling branches. Ensure the
exit route is clear of obstacles that would prevent or hinder
movement. Remember wet grass and freshly cut bark is
slippery.
uEnsure someone is nearby (but at a safe distance) in
case of an accident.
uDo not use the tool while standing in a tree, on a lad-
der or on any other unstable surface.
uKeep proper footing and balance at all times.
uHold the tool rmly with both hands when the motor is
running.
uDo not let the moving chain contact any object at the
tip of the guide bar.
uStart cutting only with the chain moving at full speed.
uDo not attempt to enter a previous cut. Always make a
fresh cut.
uWatch for shifting branches or other forces that could
close a cut and pinch or fall into the chain.
uDo not attempt to cut a branch when the diameter of
the branch exceeds the cutting length of the tool.
10
ENGLISH (Original instructions)
uAlways remove the battery from the tool and place the
chain cover assembly over the chain when storing or
transporting the tool.
uKeep the saw chain sharp and properly tensioned.
Check the tension at regular intervals.
uSwitch the tool off, allow the chain to stop and remove
the battery from the tool before carrying out any
adjustment, servicing or maintenance.
uOnly use genuine replacement parts and accessories.
uKeep handles dry, clean, and free from oil and grease.
Greasy, oily handles are slippery causing loss of control.
uThe spiked bumper may become sharp during the life
of the product. Handle with care.
uWhen handling the product the chain bar may become
hot, handle with care.
Causes and operator prevention of kickback
Kickback may occur when the nose or tip of the guide bar
touches an object, or when the wood closes in and pinches
the saw chain in the cut.
Tip contact in some cases may cause a sudden reverse reac-
tion, kicking the guide bar up and back towards the operator.
Pinching the saw chain along the top of the guide bar may
push the guide bar rapidly back towards the operator.
Either of these reactions may cause you to lose control of
the chainsaw which could result in serious personal injury.
Do not rely exclusively upon the safety devices built into your
chainsaw. As a chainsaw user, you should take several steps
to keep your cutting jobs free from accident or injury.
Kickback is the result of tool misuse and / or incorrect operat-
ing procedures or conditions and can be avoided by taking
proper precautions as given below:
uMaintain a rm grip, with thumbs and ngers
encircling the chainsaw handles. With both hands on
the chainsaw, position your body and arm to allow
you to resist kickback forces. Kickback forces can be
controlled by the operator, if proper precautions are taken.
Do not let go of the chainsaw.
uDo not overreach and do not cut above shoulder
height. This helps prevent unintended tip contact and
enables better control of the chainsaw in unexpected situ-
ations.
uOnly use replacement guide bars and chains specied
by the manufacturer. Incorrect replacement guide bars
and chains may cause chain breakage and/ or kickback.
uFollow the manufacturer's sharpening and mainte-
nance instructions for the saw chain. Decreasing the
depth gauge height can lead to increased kickback.
Safety recommendations for the chainsaw
uWe strongly recommend that rst time users obtain practi-
cal instruction in the use of the chainsaw and protective
equipment from an experienced user.
Initial practice should be completed sawing logs on a saw
horse or cradle.
uWe recommend that when carrying the chainsaw that you
remove the battery and make sure that the saw chain is
facing backwards.
uMaintain your chainsaw when not in use. Do not store
your chainsaw for any length of time without rst remov-
ing the saw chain and guide bar which should be kept
immersed in oil. Store all parts of your chainsaw in a dry,
secure place out of reach of children.
uWe recommend you drain the oil reservoir prior to storage.
uBe sure of your footing and pre-plan a safe exit from a
falling tree or branches.
uUse wedges to help control felling and prevent binding the
guide bar and saw chain in the cut.
uSaw chain care. Keep the saw chain sharp and snug on
the guide bar. Ensure the saw chain and guide bar are
clean and well oiled. Keep handles dry, clean and free
from oil and grease.
Kickback can be caused by:
uStriking branches or other objects accidentally with a tip of
the saw while the saw chain is moving.
uStriking metal, cement or any other hard material near the
wood, or buried in the wood.
uA dull or loose chain.
uCutting above shoulder height.
uLack of attention when holding or guiding the chainsaw
while cutting.
uOver-reaching. Keep proper footing and balance at all
times and do not overreach.
uDo not try to insert into a previous cut. As this could cause
kickback. Make a fresh cut every time.
uWe strongly recommend you do not attempt to operate
your chainsaw while in a tree, on a ladder or on any other
unstable surface. If you decide to do so, be advised that
these positions are extremely dangerous.
uWhen cutting a branch that is under tension, be alert for
spring back so that you will not be struck when the tension
is released.
Avoid cutting:
uPrepared timber.
uInto the ground.
uInto wire fences, nails. etc.
uInto small sized brush and saplings because slender
material may catch the saw chain and be whipped towards
you, or pull you off balance.
uDo not use your chainsaw above shoulder height.
uEnsure someone is nearby (but at a safe distance) in case
of an accident.
11
uIf for any reason you have to touch the saw chain, make
sure your chainsaw is switched off and the battery is
removed.
uThe noise from this product can exceed 80 dB(A). We
therefore recommend you take appropriate measures for
the protection of hearing
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
uInjuries caused by touching any rotating/moving parts.
uInjuries caused when changing any parts, blades or ac-
cessories.
uInjuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
uImpairment of hearing.
uHealth hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Noise and Vibration
The declared vibration emission values and the declared noise
emission value(s) stated in the technical data and the declara-
tion of conformity have been measured in accordance with a
standard test method provided by EN 62841 and may be used
for comparing one tool with another. The declared vibration
emission value and the declared noise emission value(s) may
also be used in a preliminary assessment of exposure.
Warning! The vibration and noise emission value during
actual use of the power tool can differ from the declared value
depending on the ways in which the tool is used. The vibration
level may increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
The following pictograms are shown on the tool along with the
date code:
Warning! To reduce the risk of injury, the
user must read the instruction manual.
Do not use your saw in wet conditions or
expose it to rain.
Always wear head, hearing and eye protec-
tion.
Always wear a dust mask
Always wear gloves.
Always wear non-slip safety footwear.
Always hold a chainsaw rmly with both
hands.
Pay attention to the kickback of the chain-
saw and avoid contact with the tip of the
chain bar.
Do not use chainsaw one handed"
Switch the tool off. Before performing any
maintenance on the tool, remove the battery
from the tool.
Beware of falling objects. Keep bystanders
away
To ensure continued safe operation, check
the chain tension as described in this manu-
al after every 10 minutes of use, and adjust
back to a clearance of 3 mm as required. Oil
the chain after every 10 minutes of use.
Warning! Do not touch chain at the chipping
ejection point
Direction of rotation of the chain.
To ensure continued safe operation, the
chain and guide bar must only be replaced
with original STANLEY FATMAX. Replace-
ment chain part number A6158 replacement
guide bar part number 90619609.
Directive 2000/14/EC guaranteed
sound power.
12
ENGLISH (Original instructions)
Additional safety instructions for batteries and
chargers
Batteries
uNever attempt to open for any reason.
uDo not expose the battery to water.
uDo not expose the battery to heat.
uDo not store in locations where the temperature may
exceed 40°C.
uCharge only at ambient temperatures between 10°C and
40°C.
uCharge only using the charger provided with the appli-
ance/tool. Using the wrong charger could result in an
electric shock or overheating of the battery.
uWhen disposing of batteries, follow the instructions given
in the section “Protecting the environment”.
uDo not damage/deform the battery pack either by puncture
or impact, as this may create a risk of injury and re.
uDo not charge damaged batteries.
Under extreme conditions, battery leakage may occur.
When you notice liquid on the batteries, carefully wipe the
liquid off using a cloth. Avoid skin contact.
In case of skin or eye contact, follow the instructions below.
Warning! The battery uid may cause personal
injury or damage to property. In case of skin contact,
immediately rinse with water. If redness, pain or ir-
ritation occurs seek medical attention. In case of eye
contact, rinse immediately with clean water and seek
medical attention.
Chargers
Warning! Your charger has been designed for a specic
voltage. Always check that the mains voltage corresponds to
the voltage on the rating plate.
Warning! Never attempt to replace the charger unit with a
regular mains plug.
uUse your STANLEY FATMAX charger only to charge the
battery in the appliance/tool with which it was supplied.
Other batteries could burst, causing personal injury and
damage.
uNever attempt to charge non-rechargeable batteries.
uIf the supply cord is damaged, it must be replaced by the
manufacturer or an authorised STANLEY FATMAXService
Centre in order to avoid a hazard.
uDo not expose the charger to water.
uDo not open the charger.
uDo not probe the charger.
uThe charger must be placed in a well ventilated area when
charging.
Labels on the charger
The following symbols are found on your charger:
The charger is intended for indoor use only.
Read the instruction manual before use.
Electrical safety
Your charger is double insulated; therefore no
earth wire is required. Always check that the
mains voltage corresponds to the voltage on the
rating plate. Never attempt to replace the charger
unit with a regular mains plug.
uIf the supply cord is damaged, it must be replaced by
the manufacturer or an authorised STANLEY FATMAX
Service Centre in order to avoid a hazard.
Features
1. ON/OFF trigger switch
2. Lock-off lever
3. Chain brake / front hand guard
4. Guide bar
5. Saw chain
6. Sprocket cover
7. Bar lock nut
8. Chain tensioning screw
9. Oil cap
10. Oil level indicator
11. Guide bar scabbard
12. Rear handle
13. Front handle
14. Battery pack
15. Battery pack release button
16. Hex wrench
17. Hex wrench storage
Assembly
Warning! Before assembly, remove the battery (14) from the
tool.
Charging the battery (Fig. A)
The battery needs to be charged before rst use and whenev-
er it fails to produce sufcient power on jobs that were easily
done before. The battery may become warm while charging;
this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging tem-
perature: approx. 24 °C.
Note: The charger will not charge a battery if the cell tempera-
ture is below approximately 10 °C or above 40 °C.
13
ENGLISH
(Original instructions)
The battery should be left in the charger and the charger
will begin to charge automatically when the cell temperature
warms up or cools down.
uTo charge the battery (14), insert it into the charger (18).
The battery will only t into the charger in one way. Do
not force. Be sure that the battery is fully seated in the
charger.
uPlug in the charger and switch on at the mains.
The charging indicator (18a) will blink.
The charge is complete when the charging indicator (18a)
switches to continuously on. The charger and the battery can
be left connected indenetely. The LED will switch on as the
charger occasionally tops up the battery charge.
uCharge discharged batteries within 1 week. Battery life will
be greatly diminished if stored in a discharged state.
Charger LED Modes
Charging:
Green LED Intermittent
Fully Charged:
Green LED Solid
Hot/Cold Pack Delay:
Green LED Intermittent
Red LED Solid
Note: The compatible charger(s) will not charge a faulty
battery pack. The charger will indicate a faulty battery pack by
refusing to light.
Note: This could also mean a problem with a charger. If the
charger indicates a problem, take the charger and battery
pack to be tested at an authorized service centre.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
LED glowing indenitely. The charger will keep the battery
pack fresh and fully charged.
Hot/Cold Pack Delay
When the charger detects a battery that is too hot or too cold,
it automatically starts a Hot/Cold Pack Delay, the green LED
(18a) will ash intermittently, while the red LED (18b) will
remain on continuously, suspending charging until the battery
has reached an appropriate temperature. The charger then
automatically switches to the pack charging mode. This
feature ensures maximum battery life.
Battery state of charge indicator (Fig. B)
The battery includes a state of charge indicator to quickly
determine the extent of battery life as shown in gure B. By
pressing the state of charge button (14a) you can easily view
the charge remaining in the battery as illustrated in gure B.
Installing and Removing the Battery Pack (Fig. L)
Warning! Ensure the tool/appliance is in the off position
before inserting the battery pack.
Note: For best results, make sure your battery pack is
fully charged.
uTo install the battery pack (14) into the tool handle, align
the battery pack with the rails inside the tool’s handle
and slide it into the handle until the battery pack is rmly
seated in the tool and ensure that it does not disengage.
uTo remove the battery pack from the tool, press the bat-
tery pack release button (15) and rmly pull the battery
pack out of the tool handle. Insert it into the charger as
described in the charger section of this manual.
Installing the guide bar and saw chain (Fig. D-H)
Warning! Sharp chain. Always wear protective gloves when
handling the chain. The chain is sharp and can cut you when
it is not running.
Warning! Sharp moving chain. To prevent accidental
operation, ensure that battery is removed from the tool before
performing the following operations. Failure to do this could
result in serious personal injury.
If the saw chain (5) and guide bar (4) are packed separately in
the carton, the chain has to be attached to the bar, and both
must be attached to the body of the tool.
uPlace the saw on a at, rm surface.
uRotate the bar lock nut (7) counterclockwise with the hex
wrench (16) provided.
uRemove sprocket cover (6), and bar lock nut (7).
uWearing protective gloves, grasp the saw chain (5) and
wrap it around the guide bar (4), ensuring the teeth are
facing the correct direction (Fig. H).
uEnsure the chain is properly set in the slot around the
entire guide bar.
uPlace the saw chain around the sprocket (19). While lining
up the slot on the guide bar with chain tensioning pin (20),
and the bolt (21), on the base of the tool as shown in
Fig. E.
uOnce in place, hold the bar still, replace sprocket
cover (6).
14
ENGLISH (Original instructions)
Install the rear of the sprocket cover rst, rotate it down
and make sure the bolt hole on the cover lines up with the
bolt (21), on the main housing.
uInstall the bar lock nut (7) and rotate clockwise with the
hex wrench (16) provided until snug, then loosen nut one
full turn, so that the saw chain can be properly tensioned.
uRotate the chain tensioning screw (8) clockwise to
increase tension as shown in Fig. D. Make sure the saw
chain (5) is snug around the guide bar (4). Tighten the bar
lock nut (7) until snug.
uFollow the instructions in the section Adjusting Chain Ten-
sion.
Adjusting chain tension (Fig. D-H)
Warning! Incorrect saw chain tension can cause the saw
chain to come off of the guide bar and could cause serious
injury or death.
Note: Saw chain tension should be adjusted regularly before
each use.
uWith the saw still on a rm surface check the saw chain (5)
tension. The tension is correct when the saw chain snaps
back after being pulled (3 mm) away from the guide
bar (4) with light force from the middle nger and thumb
as shown in Fig. F. There should be no “sag” between the
guide bar and the saw chain on the underside as shown in
Fig. G.
uTo adjust saw chain tension, loosen bar lock nut (7).
uRotate the chain tensioning screw ( 8 ) in the front
of the housing using the at screwdriver end of the
hex wrench (16).
uCheck saw chain tension, adjust if needed.
uDo not over-tension the saw chain as this will lead to
excessive wear and will reduce the life of the guide bar
and saw chain. Overtensioning also reduces the amount
of cuts you will get per battery charge.
uOnce saw chain tension is correct, tighten bar lock nut (7)
until snug. Torque the bar lock nut (7) to (8 Nm).
uA new chain stretches slightly during the rst few hours of
use. It is important to check the tension frequently (after
disconnecting battery remove the battery pack) during the
rst two hours of use.
Replacing the saw chain (Fig. D-H)
Warning! Sharp moving chain. To prevent accidental
operation, ensure that battery is removed from the tool before
performing the following operations. Failure to do this could
result in serious personal injury.
Caution: Sharp chain. Always wear protective gloves when
handling the chain. The chain is sharp and can cut you when it
is not running.
Caution: The chain speed of this product is 8.6 m/s. Only use
chains that are rated at greater than 8.6 m/s.
uPlace the saw on a at, rm surface.
uRemove sprocket cover (6) as described in Installing the
Guide Bar and Saw Chain section.
uTo remove the saw chain (5), rotate the chain tensioning
screw (8) in the front of the housing using the at screw-
driver end of the wrench. Turning the screw counterclock-
wise allows the guide bar (4) to recede and reduces the
tension on the chain so that it may be removed.
uWearing protective gloves, grasp the saw chain and lift the
worn saw chain out of the groove in the guide bar.
uFlip guide bar over every time you replace the chain to
ensure even wear.
uPlace the new chain in the slot of the guide bar, making
sure the saw teeth are facing the correct direction by
matching the arrow and graphic of the saw chain on the
sprocket cover (6) shown in Fig. H.
uFollow instructions for Installing the Guide Bar and
Saw Chain.
Replacement chain and bar are available from your nearest
authorized service center.
This chainsaw requires replacement (304 mm) chain.
Replacement (304 mm) bar.
Saw chain and guide bar oiling (Fig. I)
Auto oiling system
This chain saw is equipped with an auto oiling system that
keeps the saw chain and guide bar constantly lubricated.
The oil level indicator (10) shows the level of the oil in the
chain saw. If the oil level is less than a quarter full, remove the
battery from the chain saw and rell the oil tank with the
correct type of oil.
Always empty oil tank when nished cutting.
Always empty oil tank before storing this unit.
Note: Do not operate this chain saw without oil.
Note: Always use a high-quality, biodegradable bar and chain
oil for proper saw chain and bar lubrication. When pruning
trees, vegetable-based bar and chain oil is recommended, as
mineral-based oils may harm living trees. Never use dirty,
used, or contaminated oil. Doing so may damage the tool.
Filling the oil reservoir
uUnscrew counterclockwise and then remove the oil
cap (9). Fill the reservoir with the recommended bar and
chain oil until the oil level has reached the top of the oil
level indicator (10).
uRet the oil cap and tighten clockwise.
uPeriodically switch the chain saw off and check the oil
level indicator to ensure the bar and chain are being
properly oiled. Periodically switch the chain saw off and
check the oil level indicator to ensure the bar and chain
are being properly oiled.
15
ENGLISH
(Original instructions)
Transporting chainsaw (Fig. J)
uAlways turn unit off, remove the battery and cover the
guide bar (4) with the guide bar scabbard (11) when
transporting the saw.
Operation
Warning! To reduce the risk of serious personal injury, turn
unit off and remove the battery pack before making any
adjustments or removing/installing attachments or
accessories. An accidental start-up can cause injury.
Proper hand position (Fig. K)
Warning! To reduce the risk of serious personal injury, Always
use proper hand position as shown.
Warning! To reduce the risk of serious personal injury, always
hold securely in anticipation of a sudden reaction.
Proper hand position requires the left hand on the front
handle (13), with the right hand on the rear handle (12).
Operating the chain saw (Fig. K)
Warning! Read and understand all instructions. Failure to
follow all instructions listed below may result in electric shock,
re and/or serious personal injury.
uGuard Against Kickback which can result in severe injury
or death. See General Power Tool Safety Warnings and
General Chain saw Safety Warnings, and Causes and
Operator Prevention of Kickback and Kickback Safety
Features, to avoid the risk of kickback.
uDo not overreach. Do not cut above chest height. Make
sure your footing is rm. Keep feet apart. Divide your
weight evenly on both feet.
uUse a rm grip with your left hand on the front handle (13)
and your right hand on the rear handle (12) so that your
body is to the left of the guide bar (4).
uDo not hold chain saw by chain brake/front hand
guard (3). Keep elbow of left arm locked so that left arm is
straight to withstand a kickback.
Warning! Never use a cross-handed grip (left hand on the
rear handle and right hand on the front handle).
Warning! Never allow any part of your body to be in line with
the guide bar when operating the chain saw.
uNever operate while in a tree, in any awkward position
or on a ladder or other unstable surface. You may lose
control of saw causing severe injury.
uKeep the chain saw running at full speed the entire time
you are cutting.
uAllow the saw chain to cut for you. Exert only light pres-
sure. Do not put pressure on chain saw at end of cut.
Warning! When not in use always have the chain brake
engaged and battery removed.
Setting the chain brake (Fig. K, L)
Your chain saw is equipped with a chain braking system which
will stop the chain quickly in case of kickback.
uEnsure the chain brake/front hand guard (3) is in the
forward position.
uInsert the battery pack (14) into the tool.
uPull the chain brake/front hand guard (3) towards the
front handle (13) into the “set/ready” position as shown in
Fig. L.
uThe tool is now ready to use.
uAfter use, return the chain brake/front hand guard to the
forward position.
uRemove the battery.
Note: In the event of kickback, your left hand will come in
contact with the front guard, pushing it forward, toward the
workpiece. This will stop the tool.
Testing the chain brake (Fig. L)
Test the chain brake before every use to make sure it
operates correctly.
uPlace the tool on a at, rm surface. Make sure the saw
chain (5) is clear of the ground.
uGrip the tool rmly with both hands and turn the chain
saw on.
uRotate your left hand forward around the front handle (13)
so the back of your hand comes in contact with the chain
brake/front hand guard (3) and push it forward, toward the
workpiece. The saw chain should stop immediately.
Note: If saw does not stop immediately, stop use of tool and
bring it to an authorized service center nearest you.
Warning! Make sure to set chain brake before cutting.
On/Off switch (Fig. M)
Always be sure of your footing and grip the chain saw rmly
with both hands with the thumb and ngers encircling
both handles.
uTo turn the unit on, push the lock-off lever (2) in, shown in
Fig. M, and squeeze the trigger switch (1). Once the unit is
running, you may release the lock-off lever.
uIn order to keep the unit running you must continue to
squeeze the trigger. To turn the unit off, release the trigger.
Saw chain sharpening (Fig. N - P)
Caution: Sharp chain. Always wear protective gloves when
handling the chain. The chain is sharp and can cut you when it
is not running.
Warning! Sharp moving chain. To prevent accidental
operation, ensure that battery is removed from the tool before
performing the following operations. Failure to do this could
result in serious personal injury.
Note: The cutters will dull immediately if they touch the ground
or a nail while cutting.
16
ENGLISH (Original instructions)
To get the best possible performance from your chainsaw it is
important to keep the teeth of the saw chain sharp. Follow
these helpful tips for proper saw chain sharpening:
uFor best results use a 4.5 mm le and a le holder or ling
guide to sharpen your saw chain. This will ensure you
always get the correct sharpening angles.
uPlace the le holder at on the top plate and depth gauge
of the cutter.
uKeep the correct top plate (22) ling angle line of 30 ° on
your le guide parallel with your chain (le at 60 ° from
chain viewed from the side) as shown.
uSharpen cutters on one side of the chain rst. File from
the inside of each cutter to the outside. Then turn your
saw around and repeat the processes (2, 3, 4) for cutters
on the other side of the chain.
Note: Use a at le to le the tops of the rakers (portion of
chain link in front of the cutter) so they are about (0.635 mm)
below the tips of the cutters as shown below.
uKeep all cutter lengths equal as shown in Fig. O.
uIf damage is present on the chrome surface of the top
plates or side plates, le back until such damage is re-
moved.
Caution: After ling, the cutter will be sharp, use extra caution
during this process.
Note: Each time the chain is sharpened, it loses some of the
low kickback qualities and extra caution should be used. It is
recommended that a saw chain be sharpened no more than
four times.
Hex wrench storage (Fig. Q)
When not in use the hex wrench (16) should be stored in the
hex wrench storage (17) area located under the tool.
Pull the hex wrench from the hex wrench storage area to
remove it.
Push the hex wrench into the hex wrench storage area to
store it.
Stanley Track Wall System (Fig. R,S)
Warning! To reduce the risk of serious personal injury, turn
unit off and remove the battery pack before making any
adjustments or removing/installing attachments or
accessories. An accidental start-up can cause injury.
Warning! To reduce the risk of serious personal injury, do not
use a damaged Stanley Track Wall System integral hang hook
or Stanley Track Wall System. A damaged Stanley Track Wall
System integral hang hook or Stanley Track Wall System
Trackwall will not support the weight of the tool.
Warning! To reduce the risk of serious personal injury, DO
NOT suspend tool overhead or suspend objects from the
integral hang hook. ONLY suspend tool on the Stanley Track
Wall System Trackwall using the integral hang hook.
Warning! Stanley Track Wall System integral hang hook is
intended to mount the tool onto a Stanley Track Wall System
Trackwall rail.
Do not use the integral hang hook to mount the tool to any
other surface.
Warning! Stanley Track Wall System integral hang hook is not
a belt hook.
Warning! When hanging objects on a Stanley Track Wall
System Trackwall rail, adequately space the tools in order to
not exceed 35 kg per linear foot.
Warning! Before using the tool make sure that the Stanley
Track Wall System integral hang hook is returned to its
original position.
Important: Stanley Track Wall System accessories mount
compatible tools securely to the Stanley Track Wall System.
Turn tool off, remove the battery pack and
remove accessories.
Install guide bar scabbard (11) onto the guide bar (4).
Caution: Any product with exposed cutting teeth must have
them covered securely if it is to be on the Stanley Track Wall
System Trackwall.
Mount the integral hang hook (23) to the Stanley Track Wall
System Trackwall as shown in Fig. R,S. It clicks when locked
into position.
Note: Stanley Track Wall System accessories for use with
your tool are available at extra cost from your local dealer or
authorized service center.
Common cutting techniques
Felling (Fig. T, U)
The process of cutting down a tree. Do not fell trees in high
wind conditions.
Warning! Felling can result in injury. It should only be
performed by a trained person.
A retreat path should be planned and cleared as necessary
before cuts are started. The retreat path should extend back
and diagonally to the rear of the expected line of fall as
shown below.
uBefore felling is started, consider the natural lean of the
tree, the location of larger branches and the wind direction
to judge which way the tree will fall. Have wedges (wood,
plastic or aluminum) and a heavy mallet handy. Remove
dirt, stones, loose bark, nails, staples, and wire from the
tree where the felling cuts are to be made.
uNotching Undercut - Make the notch 1/3 of the diameter of
the tree, perpendicular to the direction of the fall. Make the
lower horizontal notching cut rst. This will help to avoid
pinching of either the saw chain or the guide bar when the
second notch cut is being made as shown below.
uFelling Back Cut - Make the felling back cut at least
51 mm higher than the horizontal notching cut. Keep the
felling back cut parallel to the horizontal notching cut.
17
ENGLISH
(Original instructions)
Make the felling back cut so enough wood is left to act as
a hinge. The hinge wood keeps the tree from twisting and
falling in the wrong direction.
Do not cut through the hinge as shown below.
uAs the felling cut gets close to the hinge the tree should
begin to fall. If there is any chance that the tree may
not fall in the desired direction or it may rock back and
bind the saw chain, stop cutting before the felling cut is
complete and use wedges to open the cut and drop the
tree along the desired line of fall. When the tree begins to
fall remove the chainsaw from the cut, stop the motor, put
the chainsaw down, then use the retreat path planned. Be
alert for overhead limbs falling and watch your footing.
Limbing (Fig. V)
Removing the branches from a fallen tree. When limbing,
leave larger lower limbs to support the log off the ground.
Remove the small limbs in one cut. Branches under tension
should be cut from the bottom of the branch towards the top
to avoid binding the chainsaw as shown in Fig. V. Trim limbs
from opposite side keeping tree stem between you and saw.
Never make cuts with saw between your legs or straddle the
limb to be cut.
Bucking (Fig. W, X, Y, Z)
Warning! Recommend that rst-time users should practice
cutting on a saw horse.
Cutting a felled tree or log into lengths. How you should
cut depends on how the log is supported. Use a saw horse
whenever possible as shown in Fig. W.
uAlways start a cut with the saw chain running at full speed.
uPlace the bottom spike of the chainsaw behind the area of
the initial cut as shown in Fig. W.
uTurn the chainsaw on then rotate the saw chain and bar
down into the tree, using the spike as a hinge.
uOnce the chainsaw gets to a 45 ° angle, level the chain-
saw again and repeat steps until you cut fully through.
uWhen the tree is supported along its entire length Fig. X,
make a cut from the top (overbuck), but avoid cutting the
earth as this will dull your saw quickly.
uWhen supported at one end Fig. Y, rst, cut 1/3 the
diameter from the underside (underbuck). Then make
the nishing cut by overbucking to meet the rst cut as
shown in Fig Y.
uWhen supported at both ends Fig. Z. First, cut 1/3 down
from the top overbuck. Then make the nished cut by un-
derbucking the lower 2/3 to meet the rst cut as shown in
Fig. Z.
Troubleshooting
Problem Possible cause Possible solution
Tool will not start Lock button not
pressed.
Press the lock
button.
Battery not tted Fit the battery
Battery not charged Charge the battery
Battery not tted
corectly
Remove then re-t the
battery
Chain does not stop
within 2 seconds
when the tool is
switched off
Chain tension is too
slack
Check chain tension
Bar/chain appear hot/
smoking
Oil tank empty Check oil tank level
Oil hole blocked on
chain bar
Clean oil holes and
clear the groove around
the edge of the
chainbar.
Chain tension is too
tight
Check chain tension
Guide bar sprocket
nose needs greasing
Oil the guide bar
sprocket nose
Chainsaw does not
cut well
Chain on backwards Check/modify chain
direction
Sharpen
Chainsaw not using
oil
Debris in tank Empty oil from tank and
replace
Oil hole in cap
blocked
Remove debris from
hole
Debris in chain bar Remove debris and
clean the chain bar
Debris in oil outlet Remove debris
Chainsaw stops
suddnely during
use
Battery depleted Check the charge on
the battery by pressing
the state of charge
indicator. Re-charge
battery if required.
Battery too hot Leave the battery to
cool for at least 30
minutes before
proceeding or
charging.
Current limit
protection
Restart the chainsaw.
Let the tool work at its
own pace. Do not
overload .
Maintenance
Regular maintenance ensures a long effective life for the tool.
We recommend you make the following checks on a regular
basis.
Warning! Before performing any maintenance on power tools:
u Switch off and disconnect the tool from the mains supply.
18
ENGLISH (Original instructions)
Oil level
The level in the reservoir should not be allowed to fall below
a quarter full.
Saw chain and guide bar
u After every few hours of use and before storage,
remove the guide bar and the saw chain and clean them
thoroughly.
u Make sure that the guard is clean and free from debris.
u Oil sprocket nose and chain bar via the sprocket
lubrication holes. This ensures an even distribution of
wear around the guide bar rails.
Saw chain sharpening
If you are to get the best possible performance from the tool it
is important to keep the teeth of the saw chain sharp.
Guidance for this procedure is found on the sharpener
package.
Replacing worn out saw chains
Replacement saw chains are available through retailers or
STANLEY FATMAX service agents. Always use genuine spare
parts.
Saw chain sharpness
The saw chain cutters will blunt immediately if they touch the
ground or a nail while cutting.
Saw chain tension
Regularly check the saw chain tension.
What to do if your chainsaw needs repair?
Your chainsaw is manufactured in accordance with the
relevant safety requirements. Repairs should only be carried
out by a qualied person using original spare parts otherwise
this may result in considerable danger to the user. We
recommend you keep this user manual in a safe place.
Protecting the environment
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries accord-
ing to local provisions. Further information is available at
www.2helpU.com
Technical data
SFMCCS730
Voltage VDC
18
Bar length mm
300
Chain speed (No-load) m/s
6.7
Max cutting length mm
250
Oil capacity ml
150
Weight kg 2.51 (without the saw chain, guide bar, guide bar cover, oil, battery)
Charger SFMCB11 SFMCB12 SFMCB14
Input Voltage VAC 230 230 230
Output Voltage VDC 18 18 18
Current A 1.25 2 4
Battery SFMCB201 SFMCB202 SFMCB204 SFMCB206
Voltage VDC 18 18 18 18
Capacity Ah 1.5 2.0 4.0 6.0
Type Li-Ion Li-Ion Li-Ion Li-Ion
Level of sound pressure according to EN 62841:
LpA (sound pressure) 87 dB(A), Uncertainty (K) 3 dB(A)
LWA (sound power) 99 dB(A), Uncertainty (K) 1.6 dB(A)
Vibration total values (triax vector sum) according to EN 62841:
Vibration emission value (ah) 6.5 m/s2, uncertainty (K) 1.5 m/s2
Supply of Machinery (Safety)
Regulations 2008
SFMCCS730 – Compact Chainsaw
STANLEY FATMAX declares that these products described
under “technical data” are in compliance with:
The Supply of Machinery (Safety) Regulations, 2008, S.I.
2008/1597 (as amended),
EN 62841-1:2015+A11:2022, EN 62841-4-1:2020.
The Noise Emission in the Environment by Equipment for use
Outdoors Regulations 2001, S.I. 2001/1701 (as amended).
Schedule 8.
LWA (measured sound power level) 99 dB(A), uncertainty (K)
= 1.6 dB (A),
LWA (guaranteed sound power) 101 dB(A).
These products conform to the following UK Regulations:
Electromagnetic Compatibility Regulations, 2016,
S.I.2016/1091 (as amended).
The Restriction of the Use of Certain Hazardous Substances
in Electrical and Electronic Equipment Regulations 2012, S.I.
2012/3032 (as amended).
19
ENGLISH
(Original instructions)
For more information, please contact STANLEY FATMAX at
the following address or refer to the back of the manual.
The undersigned is responsible for compilation of the technical
le and makes this declaration on behalf of
STANLEY FATMAX
Paul Featherstone
Product Director - Outdoor Products Group
STANLEY FATMAX, 270 Bath Road, Slough
Berkshire, SL1 4DX
United Kingdom28/06/2023
EC declaration of conformity
MACHINERY DIRECTIVE
%
SFMCCS730 – Compact Chainsaw
STANLEY FATMAX declares that these products described
under "technical data" are in compliance with: 2006/42/EC,
EN 62841-1:2015+A11:2022, EN 62841-4-1:2020,
2000/14/EC, Annex V
LWA (measured sound power level) 99 dB(A), uncertainty (K)
= 1.6 dB (A),
LWA (guaranteed sound power) 101 dB(A)
These products also comply with Directive
2014/30/EU and 2011/65/EU.
For more information, please contact STANLEY FATMAX at
the following address or refer to the back of the manual.
The undersigned is responsible for compilation of the
technical le and makes this declaration on behalf of
STANLEY FATMAX
Patrick Diepenbach
General Manager, Benelux
Stanley FatMax,
Egide Walschaertsstraat 14-18
2800 Mechelen, Belgium
28/06/2023
Guarantee
STANLEY FATMAX is confident of the quality of its products
and offers consumers a 12 month guarantee from the date
of purchase. This guarantee is in addition to and in no way
prejudices your statutory rights. The guarantee is valid within
the territories of the Member States of the European Union
and the European Free Trade Area and the United Kingdom.
To claim on the guarantee, the claim must be in accordance
with STANLEY FATMAX Terms and Conditions and you will
need to submit proof of purchase to the seller or an authorised
repair agent. Terms and conditions of the STANLEY FATMAX
1 year guarantee and the location of your nearest authorised
repair agent can be obtained on the Internet at www.2helpU.
com, or by contacting your local STANLEY FATMAX office at
the address indicated in this manual.
Please visit our website www.stanley.eu/3 to register Please
visit our website www.stanley.eu/3 to register
your new STANLEY FATMAX product and receive updates on
new products and special offers.
20
(Übersetzung der ursprünglichen Anweisungen)
DEUTSCH
Verwendungszweck
Ihre STANLEY FATMAX Kompakt-Kettensäge SFMCCS730
ist für leichte Säge- und Gehölzschnittaufgaben vorgesehen.
Dieses Gerät ist zum gewerblichen und privaten Einsatz
vorgesehen.
Sicherheitshinweise
Allgemeine Sicherheitswarnhinweise für
Elektrowerkzeuge
Warnung! Beachten Sie alle Sicherheits-
hinweise, Anweisungen, Darstellungen und
Daten, die Sie mit dem Gerät erhalten. Wenn
Sie die folgenden Anweisungen nicht beachten,
kann es zu elektrischem Schlag, Feuer und/oder
schweren Verletzungen kommen.
Bewahren Sie alle Warnhinweise und alle Anweisungen
gut auf. Der Begriff „Elektrowerkzeug“ in den Warnhinweisen
bezieht sich auf Ihr netzbetriebenes Elektrowerkzeug
(mit Kabel) oder auf Ihr akkubetriebenes (kabelloses)
Elektrowerkzeug.
1. Sicherheit im Arbeitsbereich
a. Halten Sie den Arbeitsbereich sauber und gut
ausgeleuchtet. Unaufgeräumte oder dunkle Bereiche
begünstigen Unfälle.
b. Betreiben Sie das Elektrowerkzeug nicht in
explosionsgefährdeten Umgebungen, in denen sich
z. B. brennbare Flüssigkeiten, Gase oder Staub
benden. Elektrowerkzeuge erzeugen Funken, die den
Staub oder die Dämpfe entzünden können.
c. Halten Sie Kinder und andere Personen während der
Benutzung von Elektrowerkzeugen fern. Ablenkung
kann dazu führen, dass Sie die Kontrolle über das Gerät
verlieren.
2. Elektrische Sicherheit
a. Der Stecker des Elektrogerätes muss in die Steckdose
passen. Ändern Sie niemals den Stecker in
irgendeiner Form. Verwenden Sie keinerlei
Adapterstecker an geerdeten Elektrogeräten.
Unveränderte Stecker und passende Steckdosen mindern
die Gefahr eines elektrischen Schlages.
b. Vermeiden Sie Körperkontakt mit geerdeten Flächen,
wie Rohren, Radiatoren, Herden und Kühlgeräten. Es
besteht eine erhöhte Gefahr für einen elektrischen Schlag,
wenn Ihr Körper geerdet ist.
c. Setzen Sie Elektrogeräte keinem Regen oder feuchter
Umgebung aus. Wenn Wasser in das Elektrowerkzeug
eindringt, erhöht sich die Gefahr eines elektrischen
Schlages.
d. Verwenden Sie das Kabel ordnungsgemäß.
Verwenden Sie niemals das Kabel, um das
Elektrowerkzeug zu tragen oder durch Ziehen vom
Netz zu trennen. Halten Sie das Kabel fern von Hitze,
Öl, scharfen Kanten oder beweglichen Teilen.
Beschädigte oder verhedderte Kabel erhöhen die Gefahr
eines elektrischen Schlags.
e. Verwenden Sie nur für den Außenbereich zugelassene
Verlängerungskabel, wenn Sie mit dem Gerät im
Freien arbeiten. Die Verwendung eines für den
Außenbereich zugelassenen Verlängerungskabels
verringert das Risiko eines elektrischen Schlags.
f. Wenn das Gerät in einer feuchten Umgebung
verwendet werden muss, schließen Sie es unbedingt
an eine Steckdose mit Fehlerstromschutzschalter
(FI-Schalter) an. Ein Fehlerstromschutzschalter verringert
das Risiko eines elektrischen Schlags.
3. Sicherheit von Personen
a. Seien Sie aufmerksam, achten Sie darauf, was Sie tun,
und gehen Sie sachgerecht mit einem Gerät um.
Benutzen Sie Elektrowerkzeuge nicht, wenn Sie müde
sind oder unter dem Einuss von Drogen, Alkohol
oder Medikamenten stehen. Ein Moment der
Unachtsamkeit beim Betrieb eines Elektrowerkzeugs kann
zu schweren Verletzungen führen.
b. Tragen Sie persönliche Schutzausrüstung. Tragen Sie
immer einen Augenschutz. Das Tragen persönlicher
Schutzausrüstung, wie Staubmaske, rutschfeste
Sicherheitsschuhe, Schutzhelm oder Gehörschutz, je
nach Art und Einsatz des Elektrowerkzeugs, verringert das
Risiko von Verletzungen.
c. Vermeiden Sie unbeabsichtigtes Starten.
Vergewissern Sie sich, dass das Gerät ausgeschaltet
ist, bevor Sie es an eine Steckdose oder einen Akku
anschließen, es hochheben oder tragen. Wenn Sie
beim Tragen des Geräts den Finger am Schalter haben
oder das Gerät eingeschaltet an die Stromversorgung
anschließen, kann dies zu Unfällen führen.
d. Entfernen Sie Einstell- oder Schraubenschlüssel,
bevor Sie das Gerät einschalten. Werkzeuge oder
Schlüssel, die an rotierenden Teilen des Geräts
angebracht sind, können zu Verletzungen führen.
e. Vermeiden Sie eine anormale Körperhaltung. Sorgen
Sie für einen sicheren Stand und halten Sie jederzeit
das Gleichgewicht. Dadurch können Sie das
Elektrowerkzeug in unerwarteten Situationen besser
kontrollieren.
f. Tragen Sie geeignete Kleidung. Tragen Sie keine weite
Kleidung und keinen Schmuck. Halten Sie Ihre Haare,
Kleidung und Handschuhe von beweglichen Teilen
fern. Lose sitzende Kleidung, Schmuck oder lange Haare
können sich in den beweglichen Teilen verfangen.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172

Stanley SFMCCS730B Manuale utente

Categoria
Motoseghe a batteria
Tipo
Manuale utente
Questo manuale è adatto anche per