GE AEC10AX Manuale del proprietario

Tipo
Manuale del proprietario
Write the model and serial
numbers here:
Model # _________________
Serial # _________________
Find these numbers on a label on
the side of the air conditioner.
GE is a trademark of the General Electric Company. Manufactured under trademark license.
Owner’s Manual
and Installation
Instructions
AIR CONDITIONERS
49-7805-2 08-18 GEA
AEC08
AEC10
AEC12
AEC14
AHC14
AEK08
AEK10
AEK12
AEF08
ENGLISH/ESPAÑOL
ROOM
SAFETY INFORMATION .........3
OPERATING INSTRUCTIONS ....5
CARE AND CLEANING
Grille and Case ........................7
Air Filter ..............................7
Outdoor Coils .........................7
Installing Remote Batteries .............7
INSTALLATION ...................8
TROUBLESHOOTING TIPS ......13
APPLIANCE
COMMUNICATION .............15
LIMITED WARRANTY ...........17
CONSUMER SUPPORT ..........18
2 49-7805-2
THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.
Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.
We take pride in the craftsmanship, innovation and design that goes into every GE Appliances
product, and we think you will too. Among other things, registration of your appliance ensures that we
can deliver important product information and warranty details when you need them.
Register your GE appliance now online. Helpful websites and phone numbers are available in the
Consumer Support section of this Owner’s Manual. You may also mail in the pre-printed registration
card included in the packing material.
49-7805-2 3
READ AND SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE
WARNING
For your safety, the information in this manual must be followed to minimize the risk of
fire, electric shock or personal injury.
Ŷ8VHWKLVDSSOLDQFHRQO\IRULWVLQWHQGHGSXUSRVHDV
described in this Owner’s Manual.
ŶThis air conditioner must be properly installed in
accordance with the Installation Instructions before it is
used.
ŶNever unplug your air conditioner by pulling on the
power cord. Always grip plug firmly and pull straight
out from the receptacle.
ŶReplace immediately all electric service cords that
have become frayed or otherwise damaged. A
damaged power supply cord must be replaced with a
new power supply cord obtained from the manufacturer
and not repaired. Do not use a cord that shows cracks
or abrasion damage along its length or at either the
plug or connector end.
ŶTurn the unit OFF and unplug your air conditioner
before cleaning.
ŶFor your safety…do not store or use combustible
materials, gasoline or other flammable vapors or
liquids in the vicinity of this or any other appliance.
ŶIf the receptacle does not match the plug, the
receptacle must be changed out by a qualified
electrician.
Ŷ'RQRWXVHPHDQVWRDFFHOHUDWHWKHGHIURVWLQJSURFHVV
or to clean, other than those recommended by the
manufacturer.
ŶThe appliance shall be stored in a room without
continuously operating ignition sources (for example:
open flames, an operating gas appliance or an
operating electric heater.
ŶDo not pierce or burn refrigerant tubing. Be aware that
refrigerants may not contain an odor.
ŶKeep ventilation openings clear of obstruction.
ŶWhen handling, installing, and operating the appliance,
care should be taken to avoid damage to the
refrigerant tubing.
ŶDo not drill holes in the unit.
ŶMaintenance, cleaning, and service should only be
performed by technicians properly trained and qualified
in the use of flammable refrigerants.
ŶGE Appliances does not support any servicing of the
air conditioner.
ŶDispose of air conditioner in accordance with Federal
and Local Regulations. Flammable refrigerants require
special disposal procedures. Contact your local
authorities for the environmentally safe disposal of your
air conditioner.
ŶThis unit is not designed for in-field service. No
service parts will be provided. Refer to warranty
section for product exchange policy. Maintenance
and repair requiring the assistance of other skilled
personnel shall be carried out under the supervision
of the person competent in the use of flammable
refrigerants.
ŶAny person who is involved with working on or
breaking into a refrigerant circuit should hold a
current valid certificate from an industry-accredited
assessment authority, which authorizes their
competence to handle refrigerants safely in
accordance with an industry recognized assessment
specification.
ŶWhen storing the appliance, care should be taken to
avoid damage to the refrigerant tubing.
SAFETY INFORMATION
Risk of Fire or Explosion. This unit contains flammable refrigerant.
Additional safety precautions must be followed.
WARNING
4 49-7805-2
IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE
READ AND SAVE THESE INSTRUCTIONS
For appliance recycling information please visit geappliances.com/recycling.
WARNING
USE OF EXTENSION CORDS
RISK OF FIRE. Could cause serious injury or death.
Ŷ'2127XVHDQH[WHQVLRQFRUGZLWKWKLV:LQGRZ$LU
Conditioner.
Ŷ'2127XVHVXUJHSURWHFWRUVRUPXOWLRXWOHWDGDSWRUV
with this Window Air Conditioner.
HOW TO CONNECT ELECTRICITY
Do not, under any circumstances, cut or remove the third
(ground) prong from the power cord. For personal safety,
this appliance must be properly grounded.
DO NOT use an adapter plug with this appliance.
The power cord of this appliance is equipped with a
3-prong (grounding) plug which mates with a standard
3-prong (grounding) wall outlet to minimize the possibility
of electric shock hazard from this appliance.
Power cord includes a current interrupter device. A
test and reset button is provided on the plug case. The
device should be tested on a periodic basis by first
pressing the TEST button and then the RESET button
while plugged into the outlet. If the TEST button does
not trip or if the RESET button will not stay engaged,
discontinue use of the air conditioner and contact a
qualified service technician.
Have the wall outlet and circuit checked by a qualified
electrician to make sure the outlet is properly grounded.
Where a 2-prong wall outlet is encountered, it is your
personal responsibility and obligation to have it replaced
with a properly grounded 3-prong wall outlet.
The air conditioner should always be plugged into its
own individual electrical outlet which has a voltage rating
that matches the rating plate.
This provides the best performance and also prevents
overloading house wiring circuits which could cause a
fire hazard from overheated wires.
See the Installation Instructions, Electrical
Requirements section for specific electrical connection
requirements.
SAFETY INFORMATION
49-7805-2 5
Controls
Features and appearance will vary.
Lights next to the touch pads on the air conditioner control panel indicate the selected settings.
Fan Fan
Mode select
Fan speed
Decrease
Temperature
set Increase
and
Decrease
Auto Fan on
Fan speed
Increase
8QLWSRZHU
on/off
NOTE: The display always shows the room temperature except
when setting the set temperature.
Auto
High
Med
Low
Cool
Fan
Eco
Reset
Filter
Fan Mode
Power
WiFi
8
Light indicates
WiFi connection
Light indicates the unit is in
the temperature set mode.
Controls
NOTE: When the bucket is full or removed, the controls cannot be
set.
1. Power Pad
Turns air conditioner on and off. When turned on, the display
will show the room temperature.
2. Display
Shows the room temperature. Shows the Set temperature
while setting the temperature in Cool or ECO modes. The Set
light will turn on while setting.
3. Temp Increase + /Decrease - Pads
8VHWRVHWWHPSHUDWXUHZKHQLQ&RRORU(&2PRGH7KH6HW
light will turn on while setting.
4. Fan Speed Pads
8VHWRVHWWKHIDQVSHHGWR/RZ0HG+LJKRU$XWRRQWKHXQLW
NOTE: On the remote control, use the fan speed Increase + /
Decrease – pads to set the fan speeds to Low, Med or High.
8VHWKH$XWRSDGWRWXUQ$XWRIDQRQ
5. Mode Pad
8VHWRVHWWKHDLUFRQGLWLRQHUWR&RRO(&2RU)DQ2QO\PRGH
6. WiFI
Enables connection of the air conditioner to the home WiFi.
Download App for details at GEAppliances.com/connect.
7. Reset Filter
LED will turn on when fan has accumulated 250 hours of run
time as a reminder to clean filter. Press Reset Filter to turn off
the LED and reset the accumulated run time.
NOTE: The default temperature reading on the display is
degree Fahrenheit ( °F). To change the display to degree
Celsius (°C), press the Temp Increase + and Temp Decrease -
buttons together and hold for 3 seconds. Repeat the process
to change back to degree Fahrenheit (°F)
8. Control Display On and Off
To reduce brightness during sleeping hours, this air conditioner
control display has an automatic off feature where the control
display will turn off completely after 5 minute of inactivity. To
illuminate the control interface, press any button on the control
display or remote control. The control display will illuminate all
previously illuminated LED’s. The control interface will now
respond to any prescribed button press after it is illuminated.
Press and hold the FAN+MODE button for 3 seconds to toggle
this feature ON or OFF. The LED’s will now stay ON anytime
the unit is ON.
9. Control sound on/off
This air conditioner will make a beep when the buttons on the
control are pushed or if the unit receives a command from
the mobile app or remote control. To silence these beeps,
simultaneously press the FAN and “-” buttons for 3 seconds.
Press these buttons again to toggle the sound back on.
Do Not Operate in Freezing Outdoor Conditions
This cool-only air conditioner was not designed for
freezing outdoor conditions. It must not be used in
freezing outdoor conditions.
Remote Control
Ŷ7RHQVXUHSURSHURSHUDWLRQDLPWKHUHPRWHFRQWURODW
the signal receiver on the air conditioner.
Ŷ0DNHVXUHQRWKLQJLVEHWZHHQWKHDLUFRQGLWLRQHUDQG
the remote control that could block the signal.
Ŷ7KHUHPRWHFRQWUROVLJQDOKDVDUDQJHRI
up to 20 feet.
Ŷ0DNHVXUHEDWWHULHVDUHIUHVKDQGLQVWDOOHGFRUUHFWO\DV
indicated on the remote control.
Ŷ5HPRWHFRQWDLQVDPDJQHWDOORZLQJLWWRDWWDFKWR
metal surfaces.
6 49-7805-2
OPERATING INSTRUCTIONS
Controls
Cool Mode
8VHWKH&RROPRGHDWLow, Med, High or Auto Fan
SpeedIRUFRROLQJ8VHWKHTemperature Increase + /
Decrease - pads to set the desired temperature between
64°F and 86°F in 1°F increments.
An electronic thermostat is used to maintain the room
temperature. The compressor will cycle on and off
to keep the room at the set level of comfort. Set the
thermostat at a lower number and the indoor air will
become cooler. Set the thermostat at a higher number
and the indoor air will become warmer.
NOTE: If the air conditioner is off and is then turned on
while set to a Cool setting or if turned from a fan setting
to a Cool setting, it may take approximately 3 minutes for
the compressor to start and cooling to begin.
Cooling Descriptions
For Normal Cooling—Select the Cool mode and High
or Med fan with a middle set temperature.
For Maximum Cooling—Select the Cool mode and
High fan with a lower set temperature.
For Quieter and Nighttime Cooling—Select the Cool
mode and Low fan with a middle set temperature.
ECO Mode
This mode optimizes the cooling power of your air
conditioner, thereby saving you energy. Once the set
point temperature has been reached, the fan will cycle
off to save energy. The fan will cycle back on periodically
to insure all cooling capacity in the system is used. This
mode is the default mode for the unit. Each time the unit
is powered off, it will restart in ECO mode ON. The first
time the unit is turned on, the settings will be 70° and
Low fan. You can adjust the fan speed and temperature
to your personal comfort.
ECO ON—Helps minimize electricity use. It is normal
for the fan to cycle off and then back on in this mode.
This on/off cycle can repeat multiple times. Because
the fan will cycle off, you may notice a variation in room
temperature and humidity.
ECO OFF—When this mode is not engaged, the fan will
run continuously, and in Cool mode the compressor will
cycle on and off to maintain room temperature.
Fan Only Mode
8VHWKH)DQ2QO\0RGHDW/RZ0HGRU+LJKIDQVSHHG
to provide air circulation and filtering without cooling.
Since fan-only settings do not provide cooling, a Set
temperature cannot be entered. The room temperature
will appear in the display.
NOTE: Auto Fan Speed cannot be used when in the Fan
Only Mode.
Auto Fan Speed
Set to Auto fan speed for the fan speed to automatically
set to the speed needed to provide optimum comfort
settings with the set temperature.
If the room needs more cooling, the fan speed will
automatically increase. If the room needs less cooling,
the fan speed will automatically decrease.
NOTE: Auto Fan Speed cannot be used when in the Fan
Only Mode.
Power Outage Recovery Feature
In the case of a power outage or interruption, the unit will
automatically restart in the settings last used after the
power is restored.
Air Direction
8VHWKHOHYHUWRDGMXVWWKHDLUGLUHFWLRQOHIWDQGULJKW
only.
49-7805-2 7
Care and Cleaning
CARE AND CLEANING
Grille and Case
Turn the air conditioner off and remove the plug from the
wall outlet before cleaning.
To clean, use water and a mild detergent. Do not use
bleach or abrasives.
Outdoor Coils
The coils on the outdoor side of the air conditioner
should be checked regularly. If they are clogged with dirt
or soot, they may be professionally cleaned.
How to Insert the Batteries in the Remote Control
1. Remove the battery cover by sliding it according to the
arrow direction.
2. Insert new batteries, making sure that the (+) and (–)
of battery are installed correctly.
3. Reattach the cover by sliding it back into position.
NOTES:
Ŷ8VH³$$$´YROWDONDOLQHEDWWHULHV'RQRWXVH
rechargeable batteries.
Ŷ5HPRYHWKHEDWWHULHVIURPWKHUHPRWHFRQWUROLIWKH
system is not going to be used for a long time.
Ŷ'RQRWPL[ROGDQGQHZEDWWHULHV'RQRWPL[DONDOLQH
standard (carbon-zinc) or rechargeable (ni-cad, ni-mh,
etc) batteries.
Air Filter
The air filter behind the front grille should be checked
and cleaned at least every 30 days or more often if
necessary.
To remove:
Pull the tab on the right side of the unit until the filter is
out.
To remove:
Open the inlet grille by pulling downward on the tabs at
the top upper corners of the inlet grille until the grille is in
a 45º position. Remove the filter.
Clean the filter with warm, soapy water. Rinse and let
the filter dry before replacing it. Do not clean the filter in
a dishwasher.
CAUTION
DO NOT operate the air conditioner
without a filter because dirt and lint will clog it and
reduce performance.
Tab Tab
8 49-7805-2
INSTALLATION INSTRUCTIONS
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
IMPORTANT Save these
instructions for local inspector’s use.
IMPORTANT Observe all
governing codes and ordinances.
Note to Installer – Be sure to leave these
instructions with the Consumer.
Note to Consumer Keep these instructions for
future reference.
Skill level – Installation of this appliance requires
basic mechanical skills.
Completion time Approximately 1 hour
We recommend that two people install
this product.
Proper installation is the responsibility of the
installer.
Product failure due to improper installation is not
covered under the Warranty.
<RX0867XVHDOOVXSSOLHGSDUWVDQGXVHSURSHU
installation procedures as described in these
instructions when installing this air conditioner.
Installation Air Conditioner
Instructions
ELECTRICAL REQUIREMENTS
Some models require a 115/120-volt AC,
60-Hz grounded outlet protected with a
15-amp time-delay fuse or circuit breaker.
The 3-prong grounding plug minimizes the
possibility of electric shock hazard. If the wall outlet
you plan to use is only a 2-prong outlet, it is your
responsibility to have it replaced with a properly
grounded 3-prong wall outlet.
Some models require 230/208-volt AC,
protected with a time-delay fuse or circuit
breaker. These models should be installed
on their own single branch circuit for best
performance and to prevent overloading
house or apartment wiring circuits, which
could cause a possible fire hazard from
overheating wires.
CAUTION
Do not, under any circumstances, cut or
remove the third (ground) prong from the
power cord.
Do not change the plug on the power cord
of this air conditioner.
Aluminum house wiring may present special
problems—consult a qualified electrician.
TOOLS YOU WILL NEED
Phillips-head screwdriver
Ruler or tape measurePencil
Level
Scissors or knife
Flat-blade screwdriver
Power cord includes a current interrupter device. A
test and reset button is provided on the plug case.
The device should be tested on a periodic basis
by first pressing the TEST button and then the
RESET button while plugged into the outlet. If the
TEST button does not trip or if the RESET button
will not stay engaged, discontinue use of the
air conditioner and contact a qualified service
technician.
Questions? Call GE Appliances at 800.GE.CARES (800.432.2737) or Visit our Website at:
GEAppliances.com
49-7805-2 9
INSTALLATION INSTRUCTIONS
Installation Instructions
Type B
Screw (6)
Type A
Screw (4)
Air
conditioner
Window locking
bracket (1)
PARTS INCLUDED
(Appearance may vary)
Frame locking
bracket (2)
(For AEC10, AED10,
and AEC12 Models)
Right
accordion
panel
Left
accordion
panel
Foam top window
gasket
Accordion panel
seal (2)
Window
sill and sash seal
(2)
Foam
Insulation (2)
Top mounting rail
Top mounting rail
seal strip
10 49-7805-2
Installation Instructions
INSTALLATION INSTRUCTIONS
2. Pull hose out
STORM WINDOW
REQUIREMENTS
A storm window frame will not allow the air
conditioner to tilt toward the outside, and will keep
it from draining properly. To adjust for this, attach a
piece of wood to the sill.
WOOD PIECES
WIDTH: 2”
LENGTH: Long enough to fit inside the window
frame.
THICKNESS: To determine the thickness, place a
piece of wood on the sill to make it 1/2” higher than
the top of the storm window frame or the vinyl frame.
Attach securely with nails or screws provided by the
installer.
WINDOW REQUIREMENTS
Ɣ These instructions are for a standard double-hung
window. You will need to modify them for other
types of windows.
Ɣ The air conditioner can be installed without the
accordion panels if needed to fit in a narrow
window. See the window opening dimensions.
Ɣ All supporting parts must be secured to firm wood,
masonry or metal.
Ɣ The electrical outlet must be within reach of the
power cord.
Ɣ Follow the dimensions in the table and illustration
for your model.
1
2
1/2” higher
than storm
window
frame
Storm window frame
Wood
Sill
1/2 higher
than vinyl frame
(on some windows)
Vinyl frame
PREPARE THE AIR
CONDITIONER
Install the top mounting rail with 4 Type A
screws from the outside of the case.
Hold the
accordion panel
in one hand and
gently pull back to
free the open end.
4
A
B
Top mounting rail
Bottom mounting rail
ATTACH THE TOP MOUNTING
RAIL SEAL STRIP
(Some models may have the seal strip already
attached to the top mounting rail. If applicable,
skip this step.)
Remove the backing from the top mounting rail
seal strip and attach the seal strip to the bottom
of the top mounting rail, along the front edge.
3
Top mounting rail
Remove
backing
from seal
strip
Top mounting rail
Seal strip
FRONT VIEW
A
B
Models A B
AEC08, AEK08, AEF08 13
1/2
Ǝ 22
1/2
´±Ǝ
AEC10, AEK10 15
1/2
´±Ǝ
AEC12, AEC14, AHC14,
AEK12
18
1/4
24” – 40”
49-7805-2 11
Installation Instructions
INSTALLATION INSTRUCTIONS
6
A
B
2 Frame locking brackets
(For AEC10 and AEC12 Models)
PREPARE THE WINDOW
Cut the window seal (2 long strips) to the proper
length. Peel off the backing and attach the
seal to the underside of the window sash. One
attached to sash and one attached to sill.
5
3 Screws
C
INSTALL THE AIR CONDITIONER
IN THE WINDOW
Place the air conditioner on the sill with the
bottom mounting rail against its back edge.
Center it and close the window securely behind
the top mounting rail. It should be level or
VOLJKWO\WLOWHGWRWKHRXWVLGH8VHDOHYHODERXWD
1/3 bubble will be the correct case slant to the
outside.
Extend the left and right accordion panels to
the vertical window sashes and attach 3 screws
through the holes in the upper panels, as
appropriate.
For AEC10 and AEC12 Models: Install the
frame locking brackets between the bottom of
the accordion panel and the window sill. Attach
with 2 screws.
NOTE: To prevent the
window sill from splitting,
drive the pilot holes before
driving the screws.
Sealing Strip
(with adhesive)
PREPARE THE AIR CONDITIONER
(cont.)
Remove the backing from the accordion seal
(two short strips). Stick one sealing strip
respectively on the left side and right side of the
accordion panels, as shown.
Slide the free end of the accordion panel into
the side panel rails. Slide the panel down. Be
sure to leave enough space to slip the top and
bottom of the frame into the rails on the cabinet.
NOTE: There is a right and a left accordion
panel. Be sure to use the proper panel for each
side.
Slide the left and right accordion panels into the
top and bottom mounting rails.
4
C
Top left
Top right
Top mounting rail
Bottom mounting rail
D
Top mounting rail
Bottom mounting rail
E
12 49-7805-2
Installation Instructions
INSTALLATION INSTRUCTIONS
7
INSTALL SUPPORT BRACKET
AND FOAM TOP WINDOW
GASKET
Cut the foam top window gasket to the window
width.
Stuff the foam
between the glass
and the window
to prevent air and
insects from getting
into the room.
NOTE: If the gasket supplied does not fit your
window, obtain appropriate material locally to
provide a proper installation seal.
A
CAUTION
To prevent broken glass
or damage to windows,
on vinyl or other similarly
constructed windows,
attach the window locking
bracket to the window side
jamb with one screw.
B
C
Wood
Vinyl
INSTALL FOAM INSULATION
Additional insulation is provided with your window
air conditioner to reduce heat leakage into the
home, reducing overall energy usage.
After the air conditioner is installed in the window
measure the length of the accordion for both
sides.
Cut the foam insulation to the measured length of
the left and right side accordion.
NOTE: Be sure to measure each accordion
because the length could be different on each
side.
Remove adhesive from back of foam insulation.
Stick the foam insulation onto the left and right
accordion, and inside of the frames.
NOTE: Be careful to cover the entire
accordion.
8
A
/
+
/
+
/RU/
B
C
49-7805-2 13
TROUBLESHOOTING TIPS
Troubleshooting Tips... Before you call for service
Save time and money! Review the charts on the following pages first and you may not need to call for service.
Problem Possible Causes What To Do
Air conditioner does
not start
The air conditioner is
unplugged.
•Make sure the air conditioner plug is pushed completely into
the outlet.
The fuse is blown/circuit
breaker is tripped.
•Check the house fuse/circuit breaker box and replace the fuse
or reset the breaker.
Power failure. •The unit will automatically re-start in the settings last used after
the power is restored.
•There is a protective time delay (approximately 3 minutes) to
prevent tripping of the compressor overload. For this reason, the
unit may not start normal cooling for 3 minutes after it is turned
back on.
The current interrupter device
is tripped.
•Press the RESET button located on the power cord plug.
•If the RESET button will not stay engaged, discontinue use of
the air conditioner and contact a qualified service technician.
Air conditioner does
not cool as it should
Airflow is restricted. •Make sure there are no curtains, blinds or furniture blocking the
front of the air conditioner.
The temp control may not be
set correctly.
•On models with touch pads: In the Cool mode, press the
DecreaseźSDG
•On models with control knobs, turn the temperature knob to a
higher number.
The air filter is dirty. •Clean the filter at least every 30 days. See the Care and
Cleaning section.
The room may have been hot. •When the air conditioner is first turned on, you need to allow
time for the room to cool down.
Cold air is escaping. •Check for open furnace registers and cold air returns.
Cooling coils have iced up. •See “Air conditioner freezing up” below.
Air conditioner
freezing up
Ice blocks the air flow and
stops the air conditioner from
cooling the room.
•On models with control knobs, set the mode control at High
Fan or High Cool with the Temp at 1 or 2.
•On models with touch pads, set the controls at High Fan or
High Cool and set the thermostat to a higher temperature.
The remote control is
not working
The batteries are inserted
incorrectly.
•Check the position of the batteries. They should be inserted in
the opposite (+) and (–) direction.
The batteries may be dead. •Replace the batteries.
Water drips outside Hot, humid weather. •This is normal.
Water drips indoors The air conditioner is not tilted
to the outside.
•For proper water disposal, make sure the air conditioner slants
slightly from the case front to the rear.
Water collects in base
pan
Moisture removed from air and
drains into base pan.
7KLVLVQRUPDOIRUDVKRUWSHULRGLQDUHDVZLWKOLWWOHKXPLGLW
\
normal for a longer period in very humid areas.
Ŷ You may hear a pinging noise caused by water being
picked up and thrown against the condenser on rainy
days or when the humidity is high. This design feature
helps remove moisture and improve efficiency.
Ŷ You may hear the thermostat click when the
compressor cycles on and off.
Ŷ Water will collect in the base pan during high humidity
or on rainy days. The water may overflow and drip
from the outdoor side of the unit.
Ŷ The fan may run even when the compressor does not.
Normal Operating Sounds
14 49-7805-2
Troubleshooting
TROUBLESHOOTING
Normal Operating Sounds
Ŷ<RXPD\KHDUDSLQJLQJQRLVHFDXVHGE\
water being picked up and thrown against the
condenser on rainy days or when the humidity is
high. This design feature helps remove moisture
and improve efficiency.
Ŷ<RXPD\KHDUWKHWKHUPRVWDWFOLFNZKHQWKH
compressor cycles on and off.
Ŷ:DWHUZLOOFROOHFWLQWKHEDVHSDQGXULQJKLJK
humidity or on rainy days. The water may
overflow and drip from the outdoor side of the
unit.
Ŷ7KHIDQPD\UXQHYHQZKHQWKHFRPSUHVVRU
does not.
Ŷ:DWHUGURSOHWVEHLQJWKURZQDJDLQVWWKHRXWVLGH
coils can make a pinging noise. This helps
cool the condenser. You can reduce this noise
by removing the side-base water hole seal by
removing 2 screws, then hole seal. Removing this
seal will lower the Energy Efficiency of your until.
NOTE: Do not drill hole in the base pan.
49-7805-2 15
Appliance Communication
APPLIANCE COMMUNICATION
GE Appliances WiFi Connect (for customers in the United States)
GE Appliances WiFi Connect Enabled*
If your Air Conditioner (AC) has a Connected Appliance Information label
located on the outside as shown below, your AC is GE Appliances WiFi Connect Enabled. A WiFi communication
card is built into the product allowing it to communicate with your smart phone for remote monitoring, control and
notifications. Please visit GEAppliances.com/connect to learn more about connected appliance features, and to learn
what connected appliance apps will work with your smart phone.
REGULATORY INFORMATION
FCC/IC Compliance Statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/television technician for help.
Labelling: Changes or modifications to this unit not expressly approved by the manufacturer could void the user’s
authority to operate the equipment.
*Select Models Only
This product has Wi-Fi capability and requires Internet connectivity and a wireless router to enable interconnection with an Energy
Management System, and/or with other external devices, systems or applications.
8VHRIWKH:RUNVZLWK$SSOH+RPH.LWORJRPHDQVWKDWDQHOHFWURQLFDFFHVVRU\KDVEHHQGHVLJQHGWRFRQQHFW
specifically to iPod touch
®
, iPhone
®
, or iPad
®
, respectively, and has been certified by the developer to meet Apple
®
performance standards. Apple is not responsible for the operation of this device or its compliance with safety and
regulatory standards.
WiFi Connectivity: For assistance with the appliance or the ConnectPlus network connectivity (for models that are WiFi
enabled or WiFi optional), please call 1-800-220-6899.
Network: GE_MODULE_XXXXNetwork: GE_MODULE_XXXX
PASSWORD: XXXXXXXX
MAC ID: XX-XX-XX-XX-XX-XX
CONTAINS FCCID: ZKJ-WCATB002
CONTAINS IC:
100229A-WCATB002
123-45-678
16 49-7805-2
NOTES
Notes
49-7805-2 17
LIMITED WARRANTY
GE Appliances Air Conditioner - One-Year Limited Warranty
EXCLUSION OF IMPLIED WARRANTIES - Your sole and exclusive remedy is product repair as provided in this Limited
àäõõäñ÷üÊñüìðóïìèçúäõõäñ÷ìèöìñæïøçìñê÷ëèìðóïìèçúäõõäñ÷ìèöòéðèõæëäñ÷äåìïì÷üòõĤ÷ñèööéòõäóäõ÷ìæøïäõóøõóòöè
are limited to one year or the shortest period allowed by law.
For US Customers: This limited warranty is extended to the original purchaser and any succeeding owner for products
purchased for home use within the USA. If the product is located in an area where service by a GE Appliances Authorized
Servicer is not available, you may be responsible for a trip charge or you may be required to bring the product to an Authorized
GE Appliances Service location for service. In Alaska, the limited warranty excludes the cost of shipping or service calls to your
home.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This limited warranty gives you
öóèæìĤæïèêäïõìêë÷öäñçüòøðäüäïöòëäùèò÷ëèõõìêë÷öúëìæëùäõüéõòðö÷ä÷è÷òö÷ä÷èÝòîñòúúëä÷üòøõïèêäïõìêë÷öäõè
æòñöøï÷üòøõïòæäïòõö÷ä÷èæòñöøðèõäģäìõöòĦæèòõüòøõö÷ä÷èđöÊ÷÷òõñèüÐèñèõäï
Warrantor US:
GE Appliances, a Haier company
Louisville KY 40225
Ŷ Customer instruction. This owner’s manual provides
information regarding operating instructions and user
controls.
Ŷ Improper installation. If you have an installation problem,
or if the air conditioner is of improper capacity, contact
your dealer or installer. You are responsible for providing
adequate electrical connecting facilities.
Ŷ Failure of the product resulting from modifications to the
product or due to unreasonable use including failure to
provide reasonable and necessary maintenance.
Ŷ Replacement of house fuses or resetting of circuit breakers.
Ŷ Failure due to corrosion on models not corrosion-protected.
Ŷ Damage to the product caused by improper power supply
voltage, accident, fire, floods or acts of God.
Ŷ Incidental or consequential damage caused by possible
defects with this air conditioner.
Ŷ Damage caused after delivery.
What Will Not Cover:
For The Period Of: Will Replace:
One Year
From the date of the
original purchase
Replacement, repair, or refund of the original retail price for any product which fails due to a
defect in materials or workmanship. If the unit is exchanged, the replacement unit is war-
õäñ÷èçéòõ÷ëèõèðäìñçèõòéüòøõóõòçøæ÷đöòõìêìñäïòñè¡üèäõúäõõäñ÷üóèõìòçÐÎúìïïä÷ì÷ö
sole discretion, replace the product with a product of the same or comparable functionality
and quality or refund the original retail price.
Ŷ Properly pack your unit. We recommend using the original
carton and packing materials.
ŶReturn the product to the retail location where it was
purchased.
Ŷ Include in the package a copy of the sales receipt or other
evidence of date of original purchase. Also print your name
and address and a description of the defect.
In Order to Make a Warranty Claim During the First 90 Days from the Date of Original Purchase:
Ŷ Locate your original sales receipt and make a note of your
model and serial number.
Ŷ Call 800.GE.CARES (800.432.2737) (in the United States) to
initiate the product replacement process.
ŶYou will be asked to provide your name, address, date of
purchase, model and serial number.
ŶGE Appliances will arrange for a carton to be sent to your
home to recover the product.
Ŷ Please return all requested materials (postage pre-paid) in the
carton provided. Please include a description of the defect.
ŶYou should receive your replacement product or refund
within 7 to 10 business days after your package is received.
In Order to Make a Warranty Claim During the Remainder of the One-Year Warranty:
Staple your receipt here. Proof of the original purchase date is needed to obtain service under the warranty.
18 49-7805-2
Printed in China
CONSUMER SUPPORT
Consumer Support
GE Appliances Website
Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day, any day
of the year! You can also shop for more great GE Appliances products and take advantage of all our on-line support
VHUYLFHVGHVLJQHGIRU\RXUFRQYHQLHQFH,QWKH86GEAppliances.com
Register Your Appliance
Register your new appliance on-line at your convenience! Timely product registration will allow for enhanced
communication and prompt service under the terms of your warranty, should the need arise. You may also mail in
WKHSUHSULQWHGUHJLVWUDWLRQFDUGLQFOXGHGLQWKHSDFNLQJPDWHULDO,QWKH86GEAppliances.com/register
Schedule Service
Expert GE Appliances repair service is only one step away from your door. Get on-line and schedule your service at
\RXUFRQYHQLHQFHDQ\GD\RIWKH\HDU,QWKH86GEAppliances.com/ge/service-and-support/service.htm
or call 800.432.2737 during normal business hours.
Extended Warranties
Purchase a GE Appliances extended warranty and learn about special discounts that are available while your
warranty is still in effect. You can purchase it on-line anytime. GE Appliances Services will still be there after your
ZDUUDQW\H[SLUHV,QWKH86GEAppliances.com/ge/service-and-support/shop-for-extended-service-plans.htm
or call 800.626.2224 during normal business hours.
Remote Connectivity
For assistance with wireless network connectivity (for models with remote enable),
visit our website at GEAppliances.com/ge/connected-appliances/RUFDOOLQWKH86
Parts and Accessories
Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes
(VISA, MasterCard and Discover cards are accepted). Order on-line today 24 hours every day.
,QWKH86GEApplianceparts.com or by phone at 877.959.8688 during normal business hours.
Instructions contained in this manual cover procedures to be performed by any user. Other servicing
generally should be referred to qualified service personnel. Caution must be exercised, since improper
servicing may cause unsafe operation.
Contact Us
If you are not satisfied with the service you receive from GE Appliances, contact us on our Website with all the
details including your phone number, or write to:
,QWKH86*HQHUDO0DQDJHU&XVWRPHU5HODWLRQV_*($SSOLDQFHV$SSOLDQFH3DUN_/RXLVYLOOH.<
GEAppliances.com/ge/service-and-support/contact.htm
Escriba los números de modelo
y serie aquí:
# de Modelo _____________
# de Serie _______________
Puede encontrar estos números
en una etiqueta en el costado
del acondicionador de aire.
GE es una marca registrada de General Electric Company. Fabricado bajo licencia de marca.
Manual del propietario
e instalación
ACONDICIONADOR DE AIRE
PARA SALA
49-7805-2 08-18 GEA
INFORMACIÓN
DE SEGURIDAD .................3
INSTRUCCIONES
DE OPERACIÓN ................5
CUIDADO Y LIMPIEZA
Grille and Case ........................7
Filtro de aire ..........................7
Bobinas para exteriores ................7
Installing Remote Batteries .............7
INSTALLATION ...................8
SOLUCIONAR PROBLEMAS ....13
COMUNICACIÓN DEL
ELECTRODOMÉSTICO ........15
GARANTÍA LIMITADA ..........17
SERVICIO AL CONSUMIDOR ...18
AEC08
AEC10
AEC12
AEC14
AHC14
AEK08
AEK10
AEK12
AEF08
2 49-7805-2
GRACIAS POR HACER QUE GE APPLIANCES SEA PARTE DE SU HOGAR.
Ya sea que haya crecido usando GE Appliances, o que ésta es su primera vez, nos complace
tenerlo en la familia.
Sentimos orgullo por el nivel de arte, innovación y diseño de cada uno de los electrodomésticos de
GE Appliances, y creemos que usted también. Entre otras cosas, el registro de su electrodoméstico
asegura que podamos entregarle información importante del producto y detalles de la garantía
cuando los necesite.
Registre su electrodoméstico GE ahora a través de Internet. Sitios Web y números telefónicos útiles
están disponibles en la sección de Soporte para el Consumidor de este Manual del Propietario.
También puede enviar una carta en la tarjeta de inscripción preimpresa que se incluye con
el material embalado.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

GE AEC10AX Manuale del proprietario

Tipo
Manuale del proprietario