Ubiquiti R2AC Guida Rapida

Marca: Ubiquiti

Modello: R2AC

Categoria: Antenne di rete

Tipo: Guida Rapida

Questo manuale è adatto anche per

2.4 GHz airMAX

BaseStation Radio with

Dedicated Wi-Fi Management

Model: R2AC

Introduction

Thank you for purchasing the Ubiquiti Networks® Rocket®2AC

Prism®. This Quick Start Guide is designed to guide you

through installation and also includes warranty terms.

Package Contents

Rocket2AC Prism GPS Antenna

2.4 GHz airMAX

BaseStation Radio with

Dedicated Wi-Fi Management

Model: R2AC

Gigabit PoE (24V, 0.5A)

with Mounting Bracket

Power Cord

Quick Start Guide

cable and earth grounding must be used as conditions of product warranty. TOUGHCable

™

designed for outdoor installations. It is the professional installer’s responsibility to follow local

country regulations, including operation within legal frequency channels, output power, and

Dynamic Frequency Selection (DFS) requirements.

Installation Requirements

• The GPS Antenna needs to have clear line of sight to thesky

for proper GPS operation.

• Shielded Category 5 (or above) cabling with drain wire

should be used for all outdoor wired Ethernet connections

and should be grounded through the AC ground of the PoE.

We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial‑grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit

www.ubnt.com/toughcable

• Surge protection should be used for all outdoor installations.

We recommend that you use two Ethernet Surge Protectors,

model ETH‑SP, one near the Rocket and the other at the

entry point to the building. The ETH‑SP will absorb power

surges and safely discharge them into the ground.

To LAN

ETH-SP

ES-8-150W

R2AC*

* Shown without the antenna.

Hardware Overview

GPS

Antenna

Connector

RP-SMA

Antenna

Connector:

Chain 1

RP-SMA

Antenna

Connector:

Chain 0

LED Panel

Port Cover

LED Panel

Signal In airOS®, you can modify the wireless

signal strength threshold values for each LED on

the Wireless tab under Signal LED Thresholds. The

default values are shown below:

LED will light blue when the wireless

signal strength is above ‑65 dBm.

LED will light blue when the wireless

signal strength is above ‑73 dBm.

LED will light blue when the wireless

signal strength is above ‑80 dBm.

LED will light blue when the wireless

signal strength is above ‑94 dBm.

GPS GPS The GPS LED will light steady blue when the

GPS signal strength is sufficient. This requires a

minimum of three satellite connections.

LAN LAN The LAN LED will light steady blue when an

active Ethernet connection is made to the LAN

port and flash when there is activity.

Power The Power LED will light blue when the

device is connected to a power source.

Ports

M/N: R2AC

24V 0.5A GigE PoE

FCC ID: SWX-R2ACN

IC: 6545A-R2ACN

LAN Port

Reset

Button

LAN The Gigabit Ethernet port is used to connect the power

and should be connected to the LAN.

Reset Button To reset to factory defaults, press and hold the

Reset button for more than 10 seconds while the Rocket is

already poweredon. Alternatively, the Rocket may be reset

remotely via a Reset button located on the bottom of the

Gigabit PoE adapter.

Hardware Installation

The Rocket Prism is designed to mount directly onto a Ubiquiti

airMAX RocketDish

™

antenna for Point‑to‑Point use or an

airMAX Sector antenna for Point‑to‑MultiPoint use.

1. Lift the release latch on the bottom of the Rocket and slide

the Port Cover off.

2. Connect an Ethernet cable to the LAN port.

M/N: R2AC

24V 0.5A GigE PoE

FCC ID: SWX-R2ACN

IC: 6545A-R2ACN

3. Replace the Port Cover.

4. Connect the RF cables (included with the antenna) to the

RP-SMA Connectors located on top of the Rocket.

Skip this step if you are using the RocketDish RD‑2G24.

5. Attach the Rocket to an antenna. Align the mounting tabs

on the back of the Rocket with the four mounting slots on

the antenna. Slide the Rocket down until it locks into place.

CHAIN 1

GPS

CHAIN 0

CHAIN 1

GPS

CHAIN 0

CHAIN 1

GPS

CHAIN 0

CHAIN 1

GPS

CHAIN 0

Mounting on a RocketDish Mounting on a Sector Antenna

6. Attach the RF cables to the RF connectors on the Rocket or

antenna as needed.

CHAIN 1

GPS

CHAIN 0

CHAIN 1

GPS

CHAIN 0

CHAIN 1

GPS

CHAIN 0

CHAIN 1

GPS

CHAIN 0

Connecting to a RocketDish Connecting to a Sector Antenna

7. Connect the GPS Antenna to the GPS Antenna Connector

on the Rocket.

CHAIN 1

GPS

CHAIN 0

CHAIN 1

GPS

CHAIN 0

CHAIN 1

GPS

CHAIN 0

CHAIN 1

GPS

CHAIN 0

Connecting the GPS Antenna Connecting the GPS Antenna

8. Slide the protective shroud over the Rocket until it locks

into place.

Skip this step if you are using the RocketDish RD‑2G24.

CHAIN 1

GPS

CHAIN 0

CHAIN 1

GPS

CHAIN 0

9. Place the GPS Antenna on the mounting hardware.

CHAIN 1

GPS

CHAIN 0

CHAIN 1

GPS

CHAIN 0

CHAIN 1

GPS

CHAIN 0

CHAIN 1

GPS

CHAIN 0

Placement on a Dish Antenna Placement on a Sector Antenna

Connecting Power

Connect the power using one of the following options:

• Using the included Gigabit PoE Adapter: Go to Connecting to

the PoE Adapter.

• Using a separate PoE switch: Connect the Ethernet cable

from the Rocket’s LAN port to a PoE‑enabled Ethernet port

on the switch.

WARNING: The switch port must comply with the

power specifications listed in the Specifications

section of this Quick Start Guide.

Connecting to the PoE Adapter

1. Connect the Ethernet cable from the Rocket to the POE

port of the PoE Adapter.

2. Connect an Ethernet cable from your LAN to the LAN port

of the PoE Adapter.

3. Connect the Power Cord to the adapter’s power port.

Connect the other end of the Power Cord to a power outlet.

Mounting the PoE Adapter (Optional)

1. Remove the PoE Mounting Bracket from the adapter, place

the bracket at the desired location, and mark the two holes.

2. Pre‑drill the holes if necessary, and secure the bracket

using two fasteners (not included).

3. Align the adapter’s slots with the tabs of the PoE Mounting

Bracket, and then slide the adapterdown.

Accessing airOS via Wi‑Fi

Verify connectivity in the airOS Configuration Interface. There

are two methods, the UNMS

™

App and Web Portal. Both are

available for 15 minutes immediately after you power on

the Rocket. If necessary, you can power cycle the Rocket to

re‑enable its Wi‑Fi.

Proceed to the section that corresponds with your preferred

method:

UNMS App

1. Download the UNMS app from the AppStore (iOS) or

Google Play

™

(Android).

2. Connect your device’s Wi‑Fi to the Rocket SSID named:

R2AC:<MAC Address>

Note: Ensure that your Wi‑Fi connection has DHCP

enabled.

3. Launch the app.

4. Tap the Rocket listed on the Connections screen.

5. Tap Connect on the Login screen.

192.168.172.1

R2AC:F09FC12EXXXX

Rocket 2AC Prism

6. Select your Country and tap Done.

7. Customize your settings as needed.

*640-00318-04*

640-00318-04

Web Portal

1. Connect your device’s Wi‑Fi to the Rocket SSID named:

R2AC:<MAC Address>

Note: Ensure that your Wi‑Fi connection has DHCP

enabled.

2. Launch a web browser and type the following URL into the

address bar: http://setup.ubnt.com

3. Enter ubnt in the Username and Password fields. Select

your Country and Language. You must agree to the Terms of

Use to use the product. Click Login.

Note:

The Country setting for U.S. product versions is

restricted to a choice of Canada, Puerto Rico, or the

U.S. to ensure compliance with FCC/IC regulations.

The airOS Configuration Interface will appear, allowing you

to customize your settings as needed. For additional details

on the airOS Configuration Interface, refer to the User Guide

available at www.ubnt.com/download/airmax

Installer Compliance Responsibility

Devices must be professionally installed and it is the

professional installer's responsibility to make sure the device is

operated within local country regulatory requirements.

Since Ubiquiti Networks equipment can be paired with a

variety of antennas and cables, the Antenna, Cable Loss, and

Output Power fields are provided to the professional installer to

assist in meeting regulatory requirements.

Specifications

R2AC

Dimensions 88 x 40 x 230 mm (3.47 x 1.58 x 9.06")

Weight 400 g (14.11 oz)

Networking Interface (1) 10/100/1000 Ethernet Port

RF Connectors (2) RP‑SMA (Waterproof)

(1) GPS (Waterproof)

LEDs Power, LAN, (4) Signal Strength

Enclosure Die‑Cast Aluminum with

White Powder Coating

Max. Power Consumption 9.5W

Power Supply 24V, 0.5A Gigabit PoE Adapter (Included)

Power Method Passive PoE (Pairs 4, 5+; 7, 8 Return)

Operating Temperature ‑40 to 80° C (‑40 to 176° F)

Operating Humidity 5 to 95% Noncondensing

ESD/EMP Protection ± 24kV Contact / Air for Ethernet

Shock and Vibrations ETSI300‑019‑1.4

Certications CE, FCC, IC

Operating Frequency (MHz)

Worldwide 2412 ‑ 2472

USA 2412 ‑ 2462

Management Radio (MHz)

Worldwide 5150 ‑ 5250

USA U‑NII‑3: 5725 ‑ 5850

Safety Notices

1. Read, follow, and keep these instructions.

2. Heed all warnings.

3. Only use attachments/accessories specified by the manufacturer.

WARNING: Do not use this product in a location that can

be submerged by water.

WARNING: Avoid using this product during an electrical

storm. There may be a remote risk of electric shock from

lightning.

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and current

requirements indicated on the manufacturer’s label. Connection to a

different power source than those specified may result in improper

operation, damage to the equipment or pose a fire hazard if the

limitations are not followed.

2. There are no operator serviceable parts inside this equipment. Service

should be provided only by a qualified service technician.

3. This equipment is provided with a detachable power cord which has

an integral safety ground wire intended for connection to a grounded

safety outlet.

a. Do not substitute the power cord with one that is not the provided

approved type. Never use an adapter plug to connect to a 2‑wire

outlet as this will defeat the continuity of the grounding wire.

b. The equipment requires the use of the ground wire as a part of the

safety certification, modification or misuse can provide a shock

hazard that can result in serious injury or death.

c. Contact a qualified electrician or the manufacturer if there

are questions about the installation prior to connecting the

equipment.

d. Protective earthing is provided by Listed AC adapter. Building

installation shall provide appropriate short‑circuit backup

protection.

e. Protective bonding must be installed in accordance with local

national wiring rules and regulations.

Limited Warranty

UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the

product(s) furnished hereunder (the “Product(s)”) shall be free from defects

in material and workmanship for a period of one (1) year from the date

of shipment by UBIQUITI NETWORKS under normal use and operation.

UBIQUITI NETWORKS’ sole and exclusive obligation and liability under

the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion,

to repair or replace any Product that fails to conform to the above

warranty during the above warranty period. The expense of removal and

reinstallation of any Product is not included in this warranty. The warranty

period of any repaired or replaced Product shall not extend beyond its

original term.

Warranty Conditions

The above warranty does not apply if the Product:

(I) has been modified and/or altered, or an addition made thereto,

except by Ubiquiti Networks, or Ubiquiti Networks’ authorized

representatives, or as approved by Ubiquiti Networks in writing;

(II) has been painted, rebranded or physically modified in any way;

(III) has been damaged due to errors or defects in cabling;

(IV) has been subjected to misuse, abuse, negligence, abnormal physical,

electromagnetic or electrical stress, including lightning strikes, or

accident;

(V) has been damaged or impaired as a result of using third party

firmware;

(VI) has no original Ubiquiti MAC label, or is missing any other original

Ubiquiti label(s); or

(VII) has not been received by Ubiquiti within 30 days of issuance of

the RMA.

In addition, the above warranty shall apply only if: the product has been

properly installed and used at all times in accordance, and in all material

respects, with the applicable Product documentation; all Ethernet cabling

runs use CAT5 (or above), and for outdoor installations, shielded Ethernet

cabling is used, and for indoor installations, indoor cabling requirements

are followed.

Returns

No Products will be accepted for replacement or repair without obtaining

a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS

during the warranty period, and the Products being received at UBIQUITI

NETWORKS’ facility freight prepaid in accordance with the RMA process of

UBIQUITI NETWORKS. Products returned without an RMA number will not

be processed and will be returned freight collect or subject to disposal.

Information on the RMA process and obtaining an RMA number can be

found at: www.ubnt.com/support/warranty

Disclaimer

EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI

NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA,

SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM

AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND,

EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO,

REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY,

ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY,

SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS

FOR A PARTICULAR PURPOSE AND NON‑INFRINGEMENT AND ANY

WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR

TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES.

BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKS NOR

ITS THIRD PARTY PROVIDERS CONTROL BUYER’S EQUIPMENT OR THE

TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING

THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE

SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS

AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS

FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD

PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS,

DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT

CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY

OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant

that the operation of the Products will be error‑free or that operation will

be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible

for damages or claims of any nature or description relating to system

performance, including coverage, buyer’s selection of products (including

the Products) for buyer’s application and/or failure of products (including

the Products) to meet government or regulatory requirements.

Limitation of Liability

EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL

UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR

DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES

(INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING

OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE

PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER

LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES.

La pagina sta caricando ...

Ubiquiti R2AC Guida Rapida

Marca: Ubiquiti

Modello: R2AC

Categoria: Antenne di rete

Tipo: Guida Rapida

Questo manuale è adatto anche per

Scarica il pdf

rapporto

in altre lingue

English: Ubiquiti R2AC Quick start guide
română: Ubiquiti R2AC Ghid de inițiere rapidă

Documenti correlati

Altri documenti

Twinkly Connection Hub Guida utente