Biostar J1800MH2 Manuale utente

Marca: Biostar

Modello: J1800MH2

Tipo: Manuale utente

Questo manuale è adatto anche per

J1900MH2

J1800MH2/J1900MH2/J2900MH2/N2940MH2 Setup Manual

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. There is no guarantee that

interference will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the contents

here and specially disclaims any implied warranties of merchantability or fitness

for any purpose. Further the vendor reserves the right to revise this publication

and to make changes to the contents here without obligation to notify any party

beforehand.

Duplication of this publication, in part or in whole, is not allowed without first

obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and we

will not be responsible for any mistakes found in this user’s manual. All the brand

and product names are trademarks of their respective companies.

Dichiarazione di conformità

sintetica

Ai sensi dell’art. 2 comma 3 del D.M.

275 del 30/10/2002

Si dichiara che questo prodotto è

conforme alle normative vigenti e

soddisfa i requisiti essenziali richiesti

dalle direttive

2004/108/CE, 2006/95/CE e

1999/05/CE

quando ad esso applicabili

Short Declaration of conformity

We declare this product is complying

with the laws in force and meeting all

the essential requirements as specified

by the directives

2004/108/CE, 2006/95/CE and

1999/05/CE

whenever these laws may be applied

Table of Contents

Chapter 1: Introduction ............................................................... 1

1.1 Before You Start ......................................................................... 1

1.2 Package Checklist ..................................................................... 1

1.3 Motherboard Specifications ....................................................... 2

1.4 Central Processing Unit (CPU) .................................................. 3

1.5 Rear Panel Connectors ............................................................. 3

1.6 Motherboard Layout .................................................................. 3

Chapter 2: Hardware Installation ................................................ 5

2.1 Connect Cooling Fans ............................................................... 5

2.2 Install System Memory .............................................................. 5

2.3 Expansion Slots ......................................................................... 7

2.4 Jumper Setting .......................................................................... 8

2.5 Headers & Connectors .............................................................. 9

Chapter 3: UEFI BIOS & Software ............................................. 13

3.1 UEFI BIOS Setup .................................................................... 13

3.2 BIOS Update ........................................................................... 13

3.3 Software ................................................................................... 17

Chapter 4: Useful Help .............................................................. 20

4.1 Driver Installation ..................................................................... 20

4.2 AMI BIOS Beep Code .............................................................. 21

4.3 Troubleshooting ....................................................................... 21

Appendix: SPEC In Other Languages ...................................... 23

Arabic ......................................................................................................... 23

French ........................................................................................................ 24

German ....................................................................................................... 25

Italian .......................................................................................................... 26

Japanese .................................................................................................... 27

Polish .......................................................................................................... 28

Portuguese ................................................................................................. 29

Russian ....................................................................................................... 30

Spanish ....................................................................................................... 31

J1800MH2/J1900MH2/J2900MH2/N2940MH2

CHAPTER 1: INTRODUCTION

1.1 Before You Start

Thank you for choosing our product. Before you start installing the

motherboard, please make sure you follow the instructions below:

 Prepare a dry and stable working environment with sufficient

lighting.

 Always disconnect the computer from power outlet before

operation.

 Before you take the motherboard out from anti-static bag,

ground yourself properly by touching any safely grounded

appliance, or use grounded wrist strap to remove the static

charge.

 Avoid touching the components on motherboard or the rear

side of the board unless necessary. Hold the board on the

edge, do not try to bend or flex the board.

 Do not leave any unfastened small parts inside the case after

installation. Loose parts will cause short circuits which may

damage the equipment.

 Keep the computer from dangerous area, such as heat

source, humid air and water.

 The operating temperatures of the computer should be 0 to

45 degrees Celsius.

 To avoid injury, be careful of:

Sharp pins on headers and connectors

Rough edges and sharp corners on the chassis

Damage to wires that could cause a short circuit

1.2 Package Checklist

 Serial ATA Cable x2

 Rear I/O Panel for ATX Case x1

 Installation Guide x1

 Fully Setup Driver DVD x1

Note: The package contents may be different due to the sales region or models in which it was

sold. For more information about the standard package in your region, please contact your

dealer or sales representative.

Motherboard Manual

1.3 Motherboard Specifications

Specifications

CPU Support

J1800MH2: Intel® Celeron® J1800 processor

J1900MH2: Intel® Celeron® J1900 processor

J2900MH2: Intel® Pentium® J2900 processor

N2940MH2: Intel® Celeron® N2940 processor

Memory

Supports Dual Channel DDR3L 1333 (1.35V/1.5V)

2 x DDR3L DIMM Memory Slot, Max. Supports up to 16 GB Memory

Each DIMM supports non-ECC 512MB/ 1/ 2/ 4/ 8 GB DDR3L module

* Please refer to www.biostar.com.tw for Memory support list.

Storage 2x SATA 3Gb/s Connector, Supports Native IDE, AHCI Mode

LAN

Realtek RTL 8111G, 10/ 100/ 1000 Mb/s auto negotiation, Half / Full duplex

capability

Audio Codec ALC662, 5.1 Channels, High Definition Audio

USB

6x USB 2.0 port (2 on rear I/Os and 4 via internal headers)

1x USB 3.0 port (1 on rear I/Os )

Expansion Slots

1x PCIe 2.0 x16 Slot (@ x1 speed)

2x PCIe x1 Slot

Rear I/Os

1x PS/2 Mouse

1x PS/2 Keyboard

1x HDMI Port

1x VGA Port

1x LAN port

1x USB 3.0 Port

2x USB 2.0 Port

3x Audio Jack

Internal I/Os

2x SATA 3.0Gb/s Connector

2x USB 2.0 Header (each header supports 2 USB 2.0 ports)

1x 4-Pin Power Connector

1x 24-Pin Power Connector

2x System Fan Connector

1x Front Panel Header

1x Front Audio Header

1x Clear CMOS Header

1x Printer Port Header

1x Serial Port Header

Form Factor Micro-ATX Form Factor, 226 mm x 188 mm

OS Support

Windows 7 / 8 / 8.1

Biostar reserves the right to add or remove support for any OS with or without

notice.

J1800MH2/J1900MH2/J2900MH2/N2940MH2

1.4 Rear Panel Connectors

Note 1: Since the audio chip supports High Definition Audio Specification, the function

of each audio jack can be defined by software. The input / output function of each audio

jack listed above represents the default setting. However, when connecting external

microphone to the audio port, please use the Line In (Blue) and Mic In (Pink) audio jack.

Note 2: Maximum resolution:

HDMI: 1920 x 1200 @60Hz

VGA: 2560 x 1600 @60Hz

1.5 Central Processing Unit (CPU)

The motherboard is equipped with an onboard Intel procrssor and a CPU cooler.

Motherboard Model: Onboard Intel CPU:

J1800MH2 Intel® Celeron® J1800 processor (Dual core, 1M Cache, 2.58 GHz)

J1900MH2 Intel® Celeron® J1900 processor (Quad core, 2M Cache, 2.42 GHz)

J2900MH2 Intel® Pentium® J2900 processor (Quad core, 2M Cache, 2.67 GHz)

N2940MH2 Intel® Celeron® N2940 processor (Quad core, 2M Cache, 2.25 GHz)

Motherboard Manual

1.6 Motherboard Layout

Note: ■ represents the 1

pin.

J1800MH2/J1900MH2/J2900MH2/N2940MH2

CHAPTER 2: HARDWARE INSTALLATION

2.1 Connect Cooling Fans

These fan headers support cooling-fans built in the computer. The fan cable and

connector may be different according to the fan manufacturer. Connect the fan

cable to the connector while matching the black wire to pin#1.

SYS_FAN1/2: System Fan Header

Pin Assignment

1 Ground

2 +12V

FAN RPM rate sense

Note: SYS_FAN1/2 support 4-pin and 3-pin head connectors. When connecting with

wires onto connectors, please note that the red wire is the positive and should be

connected to pin#2, and the black wire is Ground and should be connected to GND.

2.2 Install System Memory

A. DDR3L Modules (1.35V/1.5V)

Motherboard Manual

Step 1: Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM

on the slot such that the notch on the DIMM matches the break on the slot.

Step 2: Insert the DIMM vertically and firmly into the slot until the retaining clips

snap back in place and the DIMM is properly seated.

Note1: The DIMM must be installed to DDR3_A1 slot first.

Note2: If the DIMM does not go in smoothly, do not force it. Pull it all the way out and try again.

B. Memory Capacity

DIMM Socket Location

DDR3L Module

Total Memory Size

DDR3_A1 512MB/1GB/2GB/4GB/8GB

Max is 16GB.

DDR3_B1 512MB/1GB/2GB/4GB/8GB

C. Dual Channel Memory Installation

Please refer to the following requirements to activate Dual Channel function:

Install memory module of the same density in pairs, shown in the table.

Dual Channel Status DDR3_A1 DDR3_B1

Disabled O X

Enabled O O

(O means memory installed, X means memory not installed.)

Note: When installing more than one memory module, we recommend to use the same brand

and capacity memory on this motherboard.

J1800MH2/J1900MH2/J2900MH2/N2940MH2

2.3 Expansion Slots

PEX16_1: PCI-Express Gen2 x16 Slot (@ x1 speed)

PEX1_1/PEX1_2: PCI-Express Gen2 x1 Slot

- PCI-Express 2.0 compliant.

- Data transfer bandwidth up to 500MB/s per direction; 1GB/s in total.

Install an Expansion Card

You can install your expansion card by following steps:

1. Read the related expansion card's instruction document before

install the expansion card into the computer.

2. Remove your computer's chassis cover, screws and slot bracket

from the computer.

3. Place a card in the expansion slot and press down on the card until it

is completely seated in the slot.

4. Secure the card’s metal bracket to the chassis back panel with a

screw.

5. Replace your computer's chassis cover.

6. Power on the computer, if necessary, change BIOS settings for the

expansion card.

7. Install related driver for the expansion card.

Motherboard Manual

2.4 Jumper Setting

The illustration shows how to set up jumpers. When the jumper cap is placed on

pins, the jumper is “close”, if not, that means the jumper is “open”.

Pin opened Pin closed Pin1-2 closed

JCMOS1: Clear CMOS Header

Placing the jumper on pin2-3, it allows user to restore the BIOS safe setting and

the CMOS data. Please carefully follow the procedures to avoid damaging the

motherboard.

Pin 1-2 Close:

Normal Operation (default).

Pin 2-3 Close:

Clear CMOS data.

※

Clear CMOS Procedures:

1. Remove AC power line.

2. Set the jumper to “Pin 2-3 close”.

3. Wait for five seconds.

4. Set the jumper to “Pin 1-2 close”.

5. Power on the AC.

6. Load Optimal Defaults and save settings in CMOS.

J1800MH2/J1900MH2/J2900MH2/N2940MH2

2.5 Headers & Connectors

ATXPWR1: ATX Power Source Connector

For better compatibility, we recommend to use a standard ATX 24-pin power

supply for this connector. Make sure to find the correct orientation before

plugging the connector.

Pin Assignment Pin Assignment

13 +3.3V 1 +3.3V

14 -12V 2 +3.3V

15 Ground 3 Ground

16 PS_ON 4 +5V

17 Ground 5 Ground

18 Ground 6 +5V

19 Ground 7 Ground

20 NC 8 PW_OK

21 +5V 9 Standby Voltage+5V

22 +5V 10 +12V

23 +5V 11 +12V

24 Ground 12 +3.3V

ATXPWR2: ATX Power Source Connector

This connector will provide +12V to CPU power circuit.

Pin Assignment

1 +12V

2 +12V

3 Ground

4 Ground

Note1: Before you power on the system, please make sure that both ATXPWR1 and

ATXPWR2 connectors have been plugged-in.

Note2: Insufficient power supplied to the system may result in instability or the

peripherals not functioning properly. Use of a PSU with a higher power output is

recommended when configuring a system with more power-consuming devices.

Motherboard Manual

PANEL1: Front Panel Header

This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and

speaker connection. It allows user to connect the PC case’s front panel switch

functions.

Pin Assignment Function Pin Assignment Function

1+5V

Speaker

Connector

9 N/A

N/A

2N/A 10N/A

3 N/A 11 N/A N/A

4 Speaker 12 Power LED (+)

Power LED

5 HDD LED (+)

Hard drive LED

13 Power LED (+)

6 HDD LED (-) 14 Power LED (-)

7 Ground

Reset button

15 Power button

Power-on button

8 Reset control 16 Ground

SATA1/2: Serial ATA Connectors

These connectors connect to SATA hard disk drives via SATA cables. It satisfies

the SATA 2.0 specification and with transfer rate of 3.0Gb/s.

Pin Assignment

1 Ground

2 TX+

3 TX-

4 Ground

5 RX-

6 RX+

7 Ground

J1800MH2/J1900MH2/J2900MH2/N2940MH2

F_USB1/F_USB2: Headers for USB 2.0 Ports at Front Panel

This header allows user to connect additional USB cable on the PC front panel,

and also can be connected with a wide range of simultaneously accessible

external Plug and Play peripherals.

Pin Assignment

1 +5V (fused)

2 +5V (fused)

3 USB-

4 USB-

5 USB+

6 USB+

7 Ground

8 Ground

9 Key

10 NC

F_AUDIO1: Front Panel Audio Header

This header allows user to connect the front audio output cable with the PC front

panel. This header supports HD and AC’97 audio front panel connector.

HD Audio AC’97

Pin Assignment Pin Assignment

1 Mic Left in 1 Mic In

2 Ground 2 Ground

3 Mic Right in 3 Mic Power

4 GPIO 4 Audio Power

5 Right line in 5 RT Line Out

6 Jack Sense 6 RT Line Out

7 Front Sense 7 Reserved

8 Key 8 Key

9 Left line in 9 LFT Line Out

10 Jack Sense 10 LFT Line Out

Note1: It is recommended that you connect a high-definition front panel audio module to

this connector to avail of the motherboard's high definition audio capability.

Note2: Please try to disable the "Front Panel Jack Detection" if you want to use an

AC'97 front audio output cable. The function can be found via O.S. Audio Utility.

Motherboard Manual

J_COM1: Serial Port Connector

The motherboard has a Serial Port Connector for connecting RS-232 Port.

Pin Assignment

1 Carrier detect

2 Received data

3 Transmitted data

4 Data terminal read

5Si

nal

round

6 Data set read

7 Request to send

8 Clear to send

9 Ring indicator

10 Key

J_PRINT1: Printer Port Connector

This header allows you to connector printer on the PC.

Pin Assignment Pin Assignment

1 -Strobe 14 Ground

2 -ALF 15 Data 6

3 Data 0 16 Ground

4 -Error 17 Data 7

5 Data 1 18 Ground

6 -Init 19 -ACK

7 Data 2 20 Ground

8 -Scltin 21 Busy

9 Data 3 22 Ground

10 Ground 23 PE

11 Data 4 24 Ground

12 Ground 25 SCLT

13 Data 5 26 Key

J1800MH2/J1900MH2/J2900MH2/N2940MH2

Chapter 3: UEFI BIOS & Software

3.1 UEFI BIOS Setup

 The BIOS Setup program can be used to view and change the BIOS

settings for the computer. The BIOS Setup program is accessed by pressing

the <DEL> key after the Power-On Self-Test (POST) memory test begins

and before the operating system boot begins.

 For further information of setting up the UEFI BIOS, please refer to the UEFI

BIOS Manual in the Setup DVD.

3.2 BIOS Update

The BIOS can be updated using either of the following utilities:

 BIOSTAR BIOS Flasher: Using this utility, the BIOS can be updated from a

file on a hard disk, a USB drive (a flash drive or a USB hard drive), or a

CD-ROM.

 BIOSTAR BIOS Update Utility: It enables automated updating while in the

Windows environment. Using this utility, the BIOS can be updated from a file

on a hard disk, a USB drive (a flash drive or a USB hard drive), or a

CD-ROM, or from the file location on the Web.

BIOSTAR BIOS Flasher

BIOSTAR BIOS Flasher is a BIOS flashing utility providing you an easy and simple

way to update your BIOS via USB pen drive.

Note1: This utility only allows storage device with FAT32/16 format and single partition.

Note2: Shutting down or resetting the system while updating the BIOS will lead to system boot

failure.

Updating BIOS with BIOSTAR BIOS Flasher

1. Go to the website to download the latest BIOS file for the motherboard.

2. Then, copy and save the BIOS file into a USB flash (pen) drive.

3. Insert the USB pen drive that contains the BIOS file to the USB port.

4. Power on or reset the computer and then press <F12> during the POST process.

5. After entering the POST screen,

the BIOS-FLASHER utility pops

out. Choose [fs0] to search for the

BIOS file.

Motherboard Manual

6. Select the proper BIOS file, and a

message asking if you are sure to

flash the BIOS file. Click Yes to

start updating BIOS.

7. A dialog pops out after BIOS flash

is completed, asking you to restart

the system. Press the [Y] key to

restart system.

8. While the system boots up and the full screen logo shows up, press <DEL> key to

enter BIOS setup.

After entering the BIOS setup, please go to the Save & Exit, using the Restore

Defaults function to load Optimized Defaults, and select Save Changes and

Reset to restart the computer. Then, the BIOS Update is completed.

BIOS Update Utility (through the Internet)

1. Installing BIOS Update Utility from the DVD Driver.

2. Please make sure the system is connected to the internet before using this

function.

3. Launch BIOS Update Utility and

click the Online Update button on

the main screen.

J1800MH2/J1900MH2/J2900MH2/N2940MH2

4. An open dialog will show up to

request your agreement to start the

BIOS update. Click Yes to start the

online update procedure.

5. If there is a new BIOS version, the

utility will ask you to download it.

Click Yes to proceed.

6. After the download is completed,

you will be asked to program

(update) the BIOS or not. Click Yes

to proceed.

7. After the updating process is

finished, you will be asked you to

reboot the system. Click OK to

reboot.

8. While the system boots up and the full screen logo shows up, press <DEL> key

to enter BIOS setup.

After entering the BIOS setup, please go to the Save & Exit, using the Restore

Defaults function to load Optimized Defaults, and select Save Changes and

Reset to restart the computer. Then, the BIOS Update is completed.

BIOS Update Utility (through a BIOS file)

1. Installing BIOS Update Utility from the DVD Driver.

2. Download the proper BIOS from http://www.biostar.com.tw/

3. Launch BIOS Update Utility and

click the Update BIOS button on

the main screen.

Motherboard Manual

4. A warning message will show up

to request your agreement to start

the BIOS update. Click OK to start

the update procedure.

5. Choose the location for your BIOS

file in the system. Please select

the proper BIOS file, and then

click on Open. It will take several

minutes, please be patient.

6. After the BIOS Update process is

finished, click on OK to reboot the

system.

7. While the system boots up and the full screen logo shows up, press <DEL> key

to enter BIOS setup.

After entering the BIOS setup, please go to the Save & Exit, using the Restore

Defaults function to load Optimized Defaults, and select Save Changes and

Reset to restart the computer. Then, the BIOS Update is completed.

Backup BIOS

Click the Backup BIOS button on

the main screen for the backup of

BIOS, and select a proper location

for your backup BIOS file in the

system, and click Save.

J1800MH2/J1900MH2/J2900MH2/N2940MH2

3.3 Software

Installing Software

1. Insert the Setup DVD to the optical drive. The driver installation program would

appear if the Auto-run function has been enabled.

2. Select Software Installation, and then click on the respective software title.

3. Follow the on-screen instructions to complete the installation.

Launching Software

After the installation process is completed, you will see the software icon showing on

the desktop. Double-click the icon to launch it.

Note1: All the information and content about following software are subject to be changed without

notice. For better performance, the software is being continuously updated.

Note2: The information and pictures described below are for your reference only. The actual

information and settings on board may be slightly different from this manual.

BIOScreen Utility

This utility allows you to personalize your boot logo easily. You can choose BMP as

your boot logo so as to customize your computer.

Please follow the step-by-step instructions below to update boot logo:

 Load Image󵟊Choose the picture as the boot logo.

 Transform󵟊Transform the picture for BIOS and preview the result.

 Update Bios󵟊Write the picture to BIOS Memory to complete the update.

Motherboard Manual

eHot-Line

eHot-Line is a convenient utility that helps you to contact with our Tech-Support system.

This utility will collect the system information which is useful for analyzing the problem you

may have encountered, and then send these information to our tech-support department

to help you fix the problem.

Note: Before you use this utility, please set Outlook Express as your default e-mail client

application program.

This block will show

the information which

would be collected in

the mail.

Provide the e-mail

address that you would

like to send the copy to.

Provide the name of

the power supply

manufacturer and the

model no.

Send the mail out.

Save these information to a .txt file

Exit this dialog.

Select your area or

the area close to you.

Provide the name of

the memory module

manufacturer.

Describe condition

of your system.

represents important

information that you

must provide. Without

this information, you may

not be able to send out

the mail.

After filling up this information, click

“Send” to send the mail out. A

warning dialog would appear asking

for your confirmation; click “Send” to

confirm or “Do Not Send” to cancel.

If you want to save this information to

a .txt file, click “Save As…” and then

you will see a saving dialog appears

asking you to enter file name.

La pagina sta caricando ...

Biostar J1800MH2 Manuale utente

Marca: Biostar

Modello: J1800MH2

Tipo: Manuale utente

Questo manuale è adatto anche per

J1900MH2

Scarica il pdf

rapporto

in altre lingue

English: Biostar J1800MH2 User manual

Biostar J1800MH2 Manuale utente

Questo manuale è adatto anche per

Biostar J1800MH2 Manuale utente

in altre lingue

Documenti correlati

Altri documenti