Biostar G41-M7 V6.x Manuale del proprietario

G41-M7 Setup Manual

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. There is no guarantee

that interference will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the

contents here and specially disclaims any implied warranties of merchantability

or fitness for any purpose. Further the vendor reserves the right to revise this

publication and to make changes to the contents here without obligation to

notify any party beforehand.

Duplication of this publication, in part or in whole, is not allowed without first

obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and

we will not be responsible for any mistakes found in this user’s manual. All the

brand and product names are trademarks of their respective companies.

Table of Contents

Chapter 1: Introduction ............................................................ 1

1.1 Before You Start ................................................................................ 1

1.2 Package Checklist............................................................................. 1

1.3 Motherboard Features...................................................................... 2

1.4 Rear Panel Connectors ..................................................................... 3

1.5 Motherboard Layout......................................................................... 4

Chapter 2: Hardware Installation ............................................. 5

2.1 Installing Central Processing Unit (CPU)....................................... 5

2.2 FAN Headers...................................................................................... 7

2.3 Installing System Memory ................................................................ 8

2.4 Connectors and Slots ....................................................................... 10

Chapter 3: Headers & Jumpers Setup ..................................... 12

3.1 How to Setup Jumpers .................................................................... 12

3.2 Detail Settings.................................................................................. 12

Chapter 4: Useful Help ............................................................ 18

4.1 Driver Installation Note.................................................................. 18

4.2 Software............................................................................................ 19

4.3 Extra Information............................................................................ 23

4.4 AMI BIOS Beep Code....................................................................... 25

4.5 Troubleshooting............................................................................... 26

Appendix: SPEC In Other Languages ...................................... 28

German.................................................................................................................. 28

French .................................................................................................................... 30

Italian..................................................................................................................... 32

Spanish ................................................................................................................... 34

Portuguese ............................................................................................................ 36

Polish...................................................................................................................... 38

Russian ................................................................................................................... 40

Arabic..................................................................................................................... 42

Japanese ................................................................................................................ 44

G41-M7

1

CHAPTER 1: INTRODUCTION

1.1 B

EFORE YOU START

Thank you for choosing our product. Before you start installing the

motherboard, please make sure you follow the instructions below:

 Prepare a dry and stable working environment with

sufficient lighting.

 Always disconnect the computer from power outlet

before operation.

 Before you take the motherboard out from anti-static

bag, ground yourself properly by touching any safely

grounded appliance, or use grounded wrist strap to

remove the static charge.

 Avoid touching the components on motherboard or the

rear side of the board unless necessary. Hold the board

on the edge, do not try to bend or flex the board.

 Do not leave any unfastened small parts inside the

case after installation. Loose parts will cause short

circuits which may damage the equipment.

 Keep the computer from dangerous area, such as heat

source, humid air and water.

1.2 PACKAGE CHECKLIST

HDD Cable X 1

Serial ATA Cable X 1

Rear I/O Panel for ATX Case X 1

Installation Guide X 1

Fully Setup Driver CD X 1 (full version manual files inside)

FDD Cable X 1 (optional)

USB 2.0 Cable X1 (optional)

Serial ATA Power Cable X 1 (optional)

Note: The package contents may be different due to area or your motherboard version.

Motherboard Manual

2

1.3 MOTHERBOARD FEATURES

SPEC

CPU

LGA 775

Intel Core2Duo / Core2Quad /

Pent iu m Dual-Core / C eleron Du al- Core /

Celeron 4xx processor

(Maximum Watt: 95W)

Supports Hyper-Threading / Execute Disable Bit /

Enhanced Intel SpeedStep® / Int el Arch itecture-64 /

Extended Memory 64 Technology / Virtualization

Technology

FSB

Support 800 / 1066 / 1333 MHz

Chipset

Intel G41

Inte l ICH7

Super I/O

ITE 8718F

Provides the most commonly used legacy

Super I/O functionality.

Low Pin Count Interface

Environment Control in it iatives,

Hardware Monitor Controller

Fan Speed Contro ller

ITE's "S mart Guardian " function

Main

Memory

DIMM Slots x 2

Each DIMM supports 256MB / 512MB /

1GB / 2GB DDR2

Max Memory Capicity 4GB

Dual Channel Mode DDR2 memory module

Supports DDR2 800/667

Registered DIMM and ECC DIMM is not supported

Graphics

GMA X4500 Max Shared Video Memory is 256MB

IDE

Integr ated IDE Contro ller

Ultra DMA 33 / 66 / 100 Bus Master Mode

supports PIO Mode 0~4

SATA 2

Integrated Serial ATA Controller

Data transfer rates up to 3.0 Gb/s.

SATA Version 2.0 s pecif ic at ion co mp liant

LAN

Realtek RTL 8102EL

10 / 100 Mb/s auto negotiation

Half / Full duplex capability

Sound

Codec

ALC662

5.1 channels audio out

High Definition Audio

PCI slot x2 Supports PCI expansion cards

Slots

PCI Express x 16 slot x1 Supports PCI-E x16 expansion cards

Floppy Connector x1 Each connector supports 2 Floppy drives

Printer Port Connector x1 Each connector supports 1 Printer port

Serial port Connector x1 Connects to RS-232 Port

IDE Connector x1 Each connector supports 2 IDE device

On Board

Connectors

SATA Connector x4 Each connector supports 1 SATA devices

G41-M7

3

SPEC

Front Panel Connector x1 Supports front panel facilities

Front Audio Connector x1 Supports front panel audio function

CPU Fan Header x1 CPU Fan power supply (with Smart Fan function)

System Fan Header x1 System Fan Power supply

Clear CMOS Head er x1 Restore CMOS dat a to factory default

USB Connector x2 Each connector supports 2 front panel USB ports

Power Connector (24pin) x1 Connects to Power supply

Power Connector (4pin) x1 Connects to Power supply

Back Panel

I/O

PS/2 Keyboard x1

PS/2 Mouse x1

VGA port x1

LAN port x1

USB Port x4

Audio Jack x3

Connects to PS/2 Keyboard

Connects to PS/2 Mouse

Connect to D-SUB monitor

Connect to RJ-45 ethernet cable

Connect to USB devices

Provide Audio-In/Out and microphone connection

Board Size

182 (W) x 235 (L) mm

OS Support

Windows 2000 / XP / Vista 32 / Vista 64

Biostar reserves the right to add or remove support for

any OS with or without notice

1.4 R

EAR PANEL CONNECTORS

PS/ 2

Mouse

PS/2

Keyboard

USBX2USBX2

LAN

VGA

Line In/

Surround

Line Out

Mic In 1/

Bass/ Center

Since the audio chip supports High Definition Audio Specification, the function of each audio

jack can be defined by software. The input / output function of each audio jack listed above

represents the default setting. However, when connecting external microphone to the audio port,

please use the Line In (blue) and Mic In (Pink) audio jack.

Motherboard Manual

4

1.5 MOTHERBOARD LAYOUT

JKBMS1

JATXPWR1

JCFAN1

JUSBV1

JVGA1

JUSB1

JRJ45USB1

JAUDIO1

LAN

Super

I/O

Codec

FDD1

JPRNT1

JCOM1

PCI1

PCI2

PEX1 6_ 1

BATTERY

BIOS

JSFAN1

JUSBV2

JPAN EL 1 JCMO S1

JUSB3

JUSB2

SATA1 SATA2

SATA3

SATA4

Intel

ICH7

IDE1

JAT XPWR2

DDR2_B1

DDR2_A1

Intel

G41

JAUDIO F1

LGA775

CPU1

Note: ■ represents the 1

st

pin.

G41-M7

5

CHAPTER 2: HARDWARE INSTALLATION

2.1 I

NSTALLING CENTRAL PROCESSING UNIT (CPU)

Special Notice:

Remove Pin Cap before installation, and make good preservation

for future use. When the CPU is removed, cover the Pin Cap on the

empty socket to ensure pin legs won’t be damaged.

Pin-Cap

Step 1: Pull the socket locking lever out from the socket and then raise

the lever up to a 90-degree angle.

Motherboard Manual

6

Step 2: Look for the triangular cut edge on socket, and the golden dot on

CPU should point forwards this triangular cut edge. The CPU will

fit only in the correct orientation.

Step 2-1:

Step 2-2:

Step 3: Hold the CPU down firmly, and then lower the lever to locked

position to complete the installation.

Step 4: Put the CPU Fan and heatsink assembly on the CPU and buckle it

on the retention frame. Connect the CPU FAN power cable into

the JCFAN1. This completes the installation.

G41-M7

7

2.2 FAN HEADERS

These fan headers support cooling-fans built in the computer. The fan

cable and connector may be different due to the fan manufacturer.

Connect the fan cable to the connector while matching the black wire to

pin#1.

JCFAN1: CPU Fan Header

Assignment

1 Ground

2 Power

3 FAN RPM rate sense

41

4 Smart Fan Control

JSFAN1: System Fan Header

Assignment

1 Ground

2 +12V

13

3 FAN RPM rate sense

Note:

JCFAN1 supports 4-pin head connector; JSFAN1, 3-pin head one. When connecting

with wires onto connectors, please note that the red wire is the positive and should be

connected to pin#2, and the black wire is Ground and should be connected to GND.

Motherboard Manual

8

2.3 INSTALLING SYSTEM MEMORY

A. DDR2 module

DDR2_B1

DDR2_A1

1. Unlock a DIMM slot by pressing the retaining clips outward. Align a

DIMM on the slot such that the notch on the DIMM matches the

break on the Slot.

2. Insert the DIMM vertically and firmly into the slot until the retaining

chip snap back in place and the DIMM is properly seated.

G41-M7

9

B. Memory Capacity

DIMM Socket

Location

DDR2 Module

Total Memory

Size

DDR2_A1 256MB/512MB/1GB/2GB

DDR2_B1 256MB/512MB/1GB/2GB

Max is 4GB.

C. Dual Channel Memory Installation

Please refer to the following requirements to activate Dual Channel function:

Install memory module of the same density in pairs, shown in the table.

Dual Channel Status

DDR2_A1

DDR2_B1

Disabled O X

Disabled X O

Enabled O O

(O means memory installed; X, not installed.)

The DRAM bus width of the memory module must be the same(x8 or

x16)

Motherboard Manual

10

2.4 CONNECTORS AND SLOTS

FDD1: Floppy Disk Connector

The motherboard provides a standard floppy disk connector that supports 360K,

720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the

provided floppy drive ribbon cables.

133

234

IDE1: Hard Disk Connector

The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO

Mode 0~4, Bus Master, and Ultra DMA 33/66/100 functionality.

The IDE connector can connect a master and a slave drive, so you can connect

up to two hard disk drives.

1

39

2

40

G41-M7

11

PEX16_1: PCI-Express x16 Slot

- PCI-Express 1.0a compliant.

- Maximum theoretical realized bandwidth of 4GB/s simultaneously per

direction, for an aggregate of 8GB/s totally.

- PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.

- 2X bandwidth over the traditional PCI architecture.

PEX16_1

PCI1/PCI2: Peripheral Component Interconnect Slots

This motherboard is equipped with 2 standard PCI slots. PCI stands for

Peripheral Component Interconnect, and it is a bus standard for expansion

cards. This PCI slot is designated as 32 bits.

PCI1

PCI2

Motherboard Manual

12

CHAPTER 3: HEADERS & JUMPERS SETUP

3.1 H

OW TO SETUP JUMPERS

The illustration shows how to set up jumpers. When the jumper cap is

placed on pins, the jumper is “close”, if not, that means the jumper is

“open”.

Pin opened Pin closed Pin1-2 closed

3.2 DETAIL SETTINGS

JPANEL1: Front Panel Header

This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and

speaker connection. It allows user to connect the PC case’s front panel switch

functions.

PWR _LE D

On/Off

RST

HLED

SPK

++

+

-

1

9

8

16

Pin Assignment Function Pin Assignment Function

1 +5V 9 N/A

2 N/A 10 N/A

N/A

3 N/A 1 1 N/A N/A

4 Speaker

Speaker

Connector

12 Power LED (+)

5 HDD LED (+) 13 Power LED (+)

6 HDD LED (-)

Hard drive

LED

14 Power LED (-)

Power LED

7 Ground 15 Power button

8 Reset control

Reset button

16 Ground

Power-on button

G41-M7

13

JATXPWR2: ATX Power Source Connector

This connector allows user to connect 24-pin power connector on the ATX

power supply.

1

12

13

24

Pin Assignment Pin Assignment

13 +3.3V 1 +3.3V

14 -12V 2 +3.3V

15 Ground 3 Ground

16 PS_ON 4 +5V

17 Ground 5 Ground

18 Ground 6 +5V

19 Ground 7 Ground

20 NC 8 PW_OK

21 +5V 9 Standby Voltage+5V

22 +5V 10 +12V

23 +5V 11 +12V

24 Ground 12 +3.3V

JATXPWR1: ATX Power Source Connector

By connecting this connector, it will provide +12V to CPU power circuit.

Assignment

1 +12V

2 +12V

3 Ground

12

34

4 Ground

Note:

Before you power on the system, please make sure that both JATXPWR1 and

JATXPWR2 connectors have been plugged-in.

Motherboard Manual

14

JUSB2/JUSB3: Headers for USB 2.0 Ports at Front Panel

This motherboard provides 2 USB 2.0 headers, which allows user to connect

additional USB cable on the PC front panel, and also can be connected with

internal USB devices, like USB card reader.

Assignment

1 +5V (fused)

2 +5V (fused)

3 USB-

4 USB-

5 USB+

6 USB+

7 Ground

8 Ground

9 Key

19

2

10

JUSB2

JUSB3

10 NC

JAUDIOF1: Front Panel Audio Header

This header allows user to connect the front audio output cable with the PC front

panel. This header allows only HD audio front panel connector; AC’97 connector

is not acceptable.

Pin Assignment

1 Mic Left in

2 Ground

3 Mic Right in

4 GPIO

5 Right line in

6 Jack Sense

7 Front Sense

8 Key

9 Left line in

10 Jack Sense

1

9

2

10

G41-M7

15

JCMOS1: Clear CMOS Header

Placing the jumper on pin2-3 allows user to restore the BIOS safe setting and

the CMOS data. Please carefully follow the procedures to avoid damaging the

motherboard.

1

3

Pin 1-2 Close:

Normal Operation

(Default).

1

3

1

3

Pin 2-3 Close:

Clear CMOS data.

※ Clear CMOS Procedures:

1. Remove AC power line.

2. Set the jumper to “Pin 2-3 close”.

3. Wait for five seconds.

4. Set the jumper to “Pin 1-2 close”.

5. Power on the AC.

6. Reset your desired password or clear the CMOS data.

SATA1~SATA4: Serial ATA Connectors

The motherboard has a PCI to SATA Controller with 4channels SATA interface, it

satisfies the SATA 2.0 spec and with transfer rate of 3Gb/s.

Pin Assignment

1 Ground

2 TX+

3 TX-

4 Ground

5 RX-

6 RX+

147

SATA1 SATA2

SATA4

SATA3

7 Ground

Motherboard Manual

16

JUSBV1/JUSBV2: Power Source Headers for USB Ports

Pin 1-2 Close:

JUSBV1: +5V for USB ports at USB1/JRJ45USB1.

JUSBV2: +5V for USB ports at USB2/USBB3.

Pin 2-3 Close:

JUSBV1: +5V STB for USB ports at USB1/JRJ45USB1.

JUSBV2: +5V STB for USB ports at USB2/USBB3.

3

1

Pin 1-2 close

3

1

JUSBV1

JUSBV2

3

1

Pin 2-3 close

JCOM1: Serial port Connector

The motherboard has a Serial Port Connector for connecting RS-232 Port.

Assignment

1 Carrier detect

2 Received data

3 Transmitted data

4 Data terminal ready

5 Signal ground

6 Data set ready

7 Request to send

8 Clear to send

9 Ring indicator

10 Key

1

2

9

10

G41-M7

17

JPRNT1: Printer Port Connector

This header allows you to connector printer on the PC.

1

2

25

Pin Assignment Pin Assignment

1 -Strobe 14 Ground

2 -ALF 15 Data 6

3 Data 0 16 Ground

4 -Error 17 Data 7

5 Data 1 18 Ground

6 -Init 19 -ACK

7 Data 2 20 Ground

8 -Scltin 21 Busy

9 Data 3 22 Ground

10 Ground 23 PE

11 Data 4 24 Ground

12 Ground 25 SCLT

13 Data 5 26 Key

Motherboard Manual

18

CHAPTER 4: USEFUL HELP

4.1 D

RIVER INSTALLATION NOTE

After you installed your operating system, please insert the Fully Setup

Driver CD into your optical drive and install the driver for better system

performance.

You will see the following window after you insert the CD

The setup guide will auto detect your motherboard and operating system.

Note:

If this window didn’t show up after you insert the Driver CD, please use file browser to

locate and execute the file SETUP.EXE under your optical drive.

A. Driver Installation

To install the driver, please click on the Driver icon. The setup guide will

list the compatible driver for your motherboard and operating system.

Click on each device driver to launch the installation program.

B. Software Installation

To install the software, please click on the Software icon. The setup guide

will list the software available for your system, click on each software title

to launch the installation program.

C. Manual

Aside from the paperback manual, we also provide manual in the Driver

CD. Click on the Manual icon to browse for available manual.

Note:

You will need Acrobat Reader to open the manual file. Please download the latest version

of Acrobat Reader software from

http://www.adobe.com/products/acrobat/readstep2.html

La pagina sta caricando ...

Biostar G41-M7 V6.x Manuale del proprietario

Questo manuale è adatto anche per

Biostar G41-M7 V6.x Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti