JVC Security Camera TK-C553 Manuale utente

Marca: JVC

Modello: Security Camera TK-C553

Categoria: Telecamere di sicurezza

Tipo: Manuale utente

Questo manuale è adatto anche per

TK-C553

INSTRUCTIONS

For Customer Use:

Enter below the Serial No. which is

located on the body. Retain this

information for future reference.

Model No. TK-C553

Serial No.

COLOR DOME CAMERA

SC96896H-001

(B)

IMPORTANT SAFEGUARDS

PORTABLE CART WARNING

(symbol provided by RETAC)

S3126A

1. Read all of these instructions.

2. Save these instructions for later use.

3. All warnings on the product and in the operating instructions should be adhered to.

4. Unplug this appliance system from the wall outlet before cleaning. Do not use liquid clean-

ers or aerosol cleaners. Use a damp cloth for cleaning.

5. Do not use attachments not recommended by the appliance manufacturer as they may

cause hazards.

6. Do not use this appliance near water - for example, near a bathtub, washbowl, kitchen

sink, or laundry tub, in a wet basement, or near a swimming pool, etc.

7. Do not place this appliance on an unstable cart, stand, or table. The

appliance may fall, causing serious injury to a child or adult, and

serious damage to the appliance.

Use only with a cart or stand recommended by the manufacturer, or

sold with the appliance. Wall or shelf mounting should follow the

manufacturer’s instructions, and should use a mounting kit approved

by the manufacturer. An appliance and cart combination should be

moved with care.

Quick stops, excessive force, and uneven surfaces may cause the

appliance and cart combination to overturn.

8. Slots and openings in the cabinet and the back or bottom are pro-vided for ventilation, and

to insure reliable operation of the appliance and to protect it from overheating, these

openings must not be blocked or covered. The openings should never be blocked by

placing the appliance on a bed, sofa, rug, or other similar surface.

This appliance should never be placed near or over a radiator or heat register. This appli-

ance should not be placed in a built-in installation such as a bookcase unless proper

ventilation is provided.

9. This appliance should be operated only from the type of power source indicated on the

marking label. If you are not sure of the type of power supplied to your home, consult your

dealer or local power company. For appliance designed to operate from battery power,

refer to the operating instructions.

10. This appliance system is equipped with a 3-wire grounding type plug (a plug having a

third (grounding) pin). This plug will only fit into a grounding-type power outlet. This is a

safety feature. If you are unable to insert the plug into the outlet, contact your electrician to

replace your obsolete outlet. Do not defeat the safety purpose of the grounding plug.

11. For added protection for this product during a lightning storm, or when it is left unattended

and unused for long periods of time, unplug it form the wall outlet and disconnect the

antenna or cable system. This will prevent damage to the product due to lightning and

power-line surges.

12. Do not allow anything to rest on the power cord. Do not locate this appliance where the

cord will be abused by persons walking on it.

13. Follow all warnings and instructions marked on the appliance.

14. Do not overload wall outlets and extension cords as this can result in fire or electric shock.

15. Never push objects of any kind into this appliance through cabinet slots as they may touch

dangerous voltage points or short out parts that could result in a fire or electric shock.

Never spill liquid of any kind on the appliance.

16. Do not attempt to service this appliance yourself as opening or removing covers may

expose you to dangerous voltage or other hazards. Refer all servicing to qualified service

personnel.

17. Unplug this appliance from the wall outlet and refer servicing to qualified service person-

nel under the following conditions:

a. When the power cord or plug is damaged or frayed.

b. If liquid has been spilled into the appliance.

c. If the appliance has been exposed to rain or water.

d. If the appliance does not operate normally by following the operating instructions. Ad-

just only those controls that are covered by the operating instructions as improper

adjustment of other controls may result in damage and will often require extensive

work by a qualified technician to restore the appliance to normal operation.

e. If the appliance has been dropped or the cabinet has been damaged.

f. When the appliance exhibits a distinct change in performance - this indicates a need

for service.

18. When replacement parts are required, be sure the service technician has used replace-

ment parts specified by the manufacturer that have the same characteristics as the origi-

nal part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

19. Upon completion of any service or repairs to this appliance, ask the service technician to

perform routine safety checks to determine that the appliance is in safe operating

condition.

FOR USA AND CANADA

CAUTION:TO REDUCE THE RISK OF ELECTRIC

SHOCK. DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS

INSIDE.REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

The lightning flash wish arrowhead

symbol, within an equilateral triangle is

intended to alert the user to the pres-

ence of uninsulated "dangerous volt-

age" within the product's enclosure that

may be of sufficient magnitude to con-

stitute a risk of electric shock to per-

sons.

The exclamation point within an equi-

lateral triangle is intended to alert the

user to the presence of important op-

erating and maintenance (servicing)

instructions in the literature accompa-

nying the appliance.

WARNING:

TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT

EXPOSE THIS APPLIANCE TO RAIN

OR MOISTURE.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

Information for USA

This device complies with part 15 of the FCC Rules.

Changes or modifications not approved by JVC could

void the user’s authority to operate the equipment.

INFORMATION (FOR CANADA)

RENSEIGNEMENT

(POUR CANADA)

This Class B digital apparatus complies with

Canadian ICES-003.

Cet appareil numérique de la Class B est

conforme á la norme NMB-003 du Canada.

Due to design modifications, data given in this

instruction book are subject to possible change

without prior notice.

AVERTISSEMENT:

POUR EVITER LES RISQUES

D’INCENDIE OU D’ELECTRO-

CUTION, NE PAS EXPOSER

L’APPAREIL A L’HUMIDITE OU A LA

PLUIE.

Safety Precautions

Thank you for purchasing this product.

(These instrustions are for TK-C553U and TK-C553E)

CONTENTS

Features ...............................................................................................................................6

Operating Precautions .........................................................................................................6

Safety Precautions...............................................................................................................7

Controls, Connectors and Indicators

Camera Body ........................................................................................................ 8

Ceiling Mount ...................................................................................................... 11

SYSTEM

System with Remote Control Unit RM-P2580 ...................................................................12

INSTALLATION

Connections to Camera Terminal Board ...........................................................................15

Ceiling Installation .............................................................................................................17

Adjusting the Camera Angle..............................................................................................19

Connection for Adjustment of the Camera ........................................................................21

SETUP MENU

SETUP MENU Flow...........................................................................................................22

Menu Settings Using the Operation Buttons on the Camera Body ..................................24

Menu Settings Using the RM-P2580 .................................................................................25

SETUP MENU Screen .......................................................................................................26

VIDEO ADJUSTMENT Screen .......................................................................................... 27

MODE SELECT Screen ....................................................................................................29

COMMUNICATION Screen ...............................................................................................30

FUNCTION Screen ............................................................................................................31

BLC (Back Light Compensation) Adjustment ....................................................................32

Fixed Light Metering Areas ................................................................................................ 32

User Settable Light Metering Areas ...................................................................................33

Manual Adjustment of White Balance ...............................................................................33

AWC (One-Push Auto White Balance) Adjustment ...........................................................35

CAMERA TEXT Setting .....................................................................................................36

AUTO START DEMO .........................................................................................................38

POSITION TEXT Setting ...................................................................................................39

AUTO PATROL Setting ......................................................................................................41

SPECIFICATIONS .............................................................................................................43

Features

 Color Dome Camera with integrated

variable-focal-length lens and camera.

 Backlight compensation function

provided. Enables improvement of video

image shot with backlit conditions.

 Employment of TTL automatic tracking

white balance allows use under various

light source conditions.

 One-push auto white balance (AWC)

function.

 Control possible via external control

signal conforming to the EIA/TIA RS-

422A or RS-485 standard. The unit can

be controlled using the JVC Remote

Control Unit RM-P2580.

 Setup menus can be set using buttons

on the camera body or by external control

signal.

 Auto panning and tilting, auto scrolling

and auto patrol possible.

 Up to 6 position settings per camera.

 Setting of camera text and position text

possible.

 Digital zoom enables up to 2× zoom.

 Before starting an important recording,

be sure to perform a test recording in

order to confirm that a normal recording

is possible.

 We do not accept liability for the loss of

a recording in the case of it becoming

impossible to record due to a problem

in the video camera, VCR or video tape.

 We do not accept liability for any

damage to the camera in cases when

it is dropped because of incomplete

installation due to not observing the

installation instructions correctly.

Please be careful when installing the

camera.

Operating Precautions

● To save energy, when it is not being used

turn the system’s power off.

● This camera has been designed for indoor

use. It cannot be used outdoors.

● This camera has been designed

exclusively to be hung from the ceiling.It

may malfunction if it is placed on a surface

or if it is tilted.

● Do not install or use the camera in the

following places.

• In a place exposed to rain or moisture.

• In a place with vapor or oil soot, for

example in a kitchen.

• In a temperature outside the operating

temperature range (–10°C to 50°C).

• Near a source of radiation, X-rays, strong

radio waves or magnetism.

• In a place subject to vibration.

• In a place with excessive dirt.

● If this camera and the cables connected

to this camera are used where there are

strong electromagnetic waves or where

there is magnetism present, for example

near a radio or TV transmitter, power

transformer or an electric motor, the picture

may produce noise and the colors may be

affected.

● This camera incorporates an AGC circuit.

As a result, when it is used under low light

conditions, the camera sensitivity is

automatically boosted and the picture may

look uneven. This is not a malfunction

however.

● The white balance setting when used

under a fluorescent lamp should be ATW

(Auto White).

● When this camera is used in the ATW

mode, the recorded colors may be slightly

different from the actual colors due to the

operational principles of the auto-tracking

white balance circuit. This is however not

a malfunction.

● If a high-intensity object (such as a lamp)

is shot, the image on the screen may have

vertical lines (smear) or blur (blooming) at

its periphery. This is a characteristic of the

CCD, and is not a defect.

● Resolution decreases as the digital zoom

ratio is increased.

● Do not touch the dome cover of the lens

directly with your hand, contamination of

this cover will lead to a deterioration of the

picture quality.

● Observe the following when carrying out

camera maintenance.

• Turn the power OFF before proceeding

to carry out maintenance.

• Clean the dome cover lens using a lens

wiper cloth (or a tissue).

If it is contaminated seriously, clean the

contaminated part with a cloth (or a tissue)

which has been soaked in a solution of

water and a neutral detergent.

Precautions for Use with the RM-P2580

• The focus button will be inoperative.

• The Pan/Tilt speed becomes as shown in

the following table.

• During auto pan operation, the PAN/TILT

and ZOOM buttons remain inoperative.

• The auto pan start/stop positions cannot be

set.

• Auto patrol works.

 See page 41.

Safety Precautions

• Installation of this unit requires expertise.

Please contact your dealer for details.

• The ceiling to mount the TK-C553 has to

be strong enough to support ten times the

weight of this product.

If the ceiling is not strong enough, make

sure to apply reinforcement to the ceiling

before installation.

• Be sure to tighten the screws and nuts se-

curely, Insufficient tightening may cause the

unit to fall from its mount.

• The unit is to be powered by a DC 12 V or

an AC 24 V power supply.

The AC 24 V power supply should conform

to the following:

Isolated power supply only (E type)

Class 2 only (U type)

RM-P2580 P/T SPEED 2 4 6 8

TK-C553 operation 2 4 4 4

Camera Body

Controls, Connectors and Indicators

MONITOR terminal (RCA pin)

For connecting a monitor when determin-

ing camera angle, etc. (High impedance)

Camera head

Horizontal LOCK screw

When adjusting the camera angles

horizontal rotation, this screw is loosened

for adjustment and tightened to maintain

the angle.

Camera clamp

Fix the camera body to the ceiling mount

by fastening the camera clamping screw

of the ceiling mount to this clamp.

Operation buttons

LEFT/RIGHT/UP/DOWN

Used to move the cursor on the SETUP

MENU screens and for changing set

values.

AWC

Press for about 1 second to activate the

one-push auto white balance. Even if the

color temperature changes later on, the

white balance does not adjust to the

change.

SET button

Press to display and close the setup

screen.

MONITOR

LOCK

LEFT RIGHT

SET

NOT USED

L/L

INT

OFF

TERMINATION

AWC

DOWN

 Body Surface

View when the dome cover is removed.

DIP switch

 Video synchronization selector

switch

Switches the synchronization method of

the camera image.

INT: Internal synchronization

L/L: The camera’s vertical synchroniza-

tion is matched with the frequency

of the AC 24 V line power supply.

When switching between multiple cam-

eras using a switcher, selecting the LL

mode and adjusting the vertical phase

can reduce the monitor sync distur-

bances occurring when the camera im-

age is switched.

 Control signal termination ON/OFF

switch

This is a termination ON/OFF switch

between the “RX+” and “RX–” control

signal connection terminals.

ON: The “RX+” to “RX–” route is

terminated by a 110-Ω resistor.

OFF: The RX+ to RX– route is not

terminated.

Terminal board

To connect the coaxial cable used as the

video signal cable, the power cable,

control signal cable, etc.

( See page 15)

Video output terminal

Outputs composite video signals (1 V

(p-p), output impedance 75Ω).

Should be connected to video input

terminal on monitor, switcher, or remote

control unit.

Control signal connection terminals

Terminals for inputting signals with

electrical characteristics conforming to

the EIA/TIA RS-422A or RS-485 standard.

Connected to the optional Remote

Control Unit RM-P2580, etc.

DC 12 V / AC 24 V input terminals

To input DC 12 V or AC 24 V power.

The AC 24 V power supply should

conform to the following:

U-type: Class 2 only

E-type: Isolated power supply only

Terminal board cover

Protects the cable connection terminals

from dirt, etc.

Camera body mounting guides (× 3)

To be inserted into the guide holes of the

ceiling mount.

Drop prevention wire hook

Attach the drop prevention wire to this

hook.

Camera positioning alignment mark

When mounting the camera onto the

ceiling mount, align this mark with the

mark on the mount.

Controls, Connectors and Indicators

Camera Body

 Body Underside

(Condition with terminal board attached.)

Ceiling Mount

Mounting holes (

Use these holes to attach the ceiling

mount to the ceiling.

Guide holes for mounting camera (× 3)

Guide holes for mounting the camera.

The camera body mounting guides

are inserted into these holes.

Camera clamping screw

To hold the camera in place, be sure to

use this screw to lock the camera clamp

Camera positioning alignment mark

Positioning mark for when the camera

body is attached.

Drop prevention wire hook

Attach this wire to the drop prevention

wire hook

on the camera body.

System with Remote Control Unit RM-P2580

System with up to 8 cameras. (Six position settings available for each camera.)

PAL

REC

PLAY

FFREW

REVERSE

PAUSE/

STILL

REC

CHECK

STOP/EJECT

COUNT/

CLOCK

TIME

MODE

TIMER

REC

AL/PL

RESET

VIDEO CASSETTE RECORDER

SHIFT/TRACKING

SET/V.LOCK

RESET

/CANCEL

OPERATE

SR-L910E

OPE. LOCK

TO CAMERA

DATA I / O

COM

1 2 3 4 5 6 7 8

COM

9/1

10/2

11/3

12/4

13/5

14/6

15/7

16/8

COM

CAMERA

UNIT

ALARM

AUTO

431 2 875 6

2 3 4 5 6 7

MONITOR

OUTPUT

MONITOR

SERIAL-2

SERIAL-1

VIDEO INPUT

VIDEO OUTPUT

OUTPUT

2 3 4 5 6 7

POWER

OFF

AC INPUT

MONITOR

COM

VIDEO IN

CAMERA

CAM SW

OUT

MONITOR

OUTPUT 2

MONITOR

OUTPUT 1

CAMERA ID:01

TERMINATION:OFF

CAMERA ID:02

TERMINATION:OFF

CAMERA ID:08

TERMINATION:ON

COLOR DOME CAMERA

TK-C553

COLOR DOME CAMERA

TK-C553

COLOR DOME CAMERA

TK-C553

AC24V

Control signal cable

Video signal cable

Power cable

CAMERA 1

CAMERA 2

CAMERA 8

Remote Control Unit

RM-P2580

Time lapse VCR

SYSTEM

• Turn OFF the power supply to all equipment to be used before making connections.

• Read the Instruction Manual for each piece of equipment to be used before making

connections.

• The control signal cable cannot be used for loop connection.

TX+ A

TX– B

RX+ C

RX– D

TX+ A

TX– B

RX+ C

RX– D

TX+ A

TX– B

RX+ C

RX– D

RX+ A

RX– B

TX+ C

TX– D

RM-P2580

Connecting the control signal cable

(Use a twisted-pair cable for connection.  See page 16.)

Connect:

Camera TX+ to RM-P2580 RX+

Camera TX– to RM-P2580 RX–

Camera RX+ to RM-P2580 TX+

Camera RX– to RM-P2580 TX–

The A B C D marks indicated on both the camera

terminals and the RM-P2580 terminals facilitate correct

connections. Connect the terminals with identical

marks.

Camera 1 terminal board

Camera 2 terminal board

Camera 3 terminal board

RX+ C

RX– D

A TX+

B TX–

Terminal board

Lug plates

DC 12 V or AC 24 V

power cable

To DC 12 V or AC 24 V power supply

Control signal cable

To Remote Control Unit (RM-P2580)

Video

signal cable

Settings

 CAMERA FACE

• Video synchronization selector switch

(INT/LL)

Set to LL (Line Lock) on all cameras, and

align V.PHASE.

( See page 29.)

• Control signal termination ON/OFF switch

(TERMINATION OFF/ON)

Set this to ON only on the camera placed

at the end of the control signal cable.

Set to OFF on all other cameras.

Menu Screen Settings

 COMMUNICATION menu screen

• MODE item: Set to DUPLEX

• STYLE item: Set to MULTIDROP

• ID item: Set the camera ID.

For each camera, match the ID with the

VIDEO INPUT number of the RM-

P2580.

* Settings on the COMMUNICATION

menu screen are performed using the

operation buttons on the front section

of the camera.

MEMO

Following selection of MEMORY, the settings

on the COMMUNICATION menu will not be

valid before the power has been turned on

again.

 FUNCTION menu screen

Screen for making settings related to the

Auto Patrol and Auto Pan functions and

display of text.

The number shown in

the MM part of ID-

MMshould be correct.

NOT USED

MONITOR

LOCK

LEFT RIGHT

SET

DOWN

OFF

TERMINATION

INT

L/L

INT

OFF

TERMINATION

AWC

PROT OOL:DUPLEXID-05C

MONITOR screen

“DUPLEX” should be

displayed.

• Settings on the FUNCTION menu are

performed using the operation buttons

on the RM-P2580. They cannot be

made using the operation buttons on

the camera body.

• Make settings on other menus as

required.

Monitor screen (example showing camera ID as “05”)

SYSTEM

System with Remote Control Unit RM-P2580

MEMO

When operating a system using the RM-

P2580, several cameras (up to 16) can be

connected and used on one control signal

cable. Consequently, an incorrect switch

setting on just a single camera will cause

the entire system to work incorrectly.

• Confirm switch settings on the screen

as follows.

q Confirm that the image from the camera

to be checked is displayed on the monitor.

w Turn OFF and then ON the power to the

camera to be checked.

e When the STYLE item is MULTIDROP,

characters similar to those shown in the

figure below are displayed for about 5

seconds. They do not appear in the case

of POINT to POINT.

r Confirm that “DUPLEX” and “ID-MM” are

displayed and that the ID number is the

correct number (the number should be the

same as the number of the VIDEO INPUT

terminal to which the camera is connected

on the rear panel of the RM-P2580).

t If wrong, set the MODE item, STYLE item

and camera ID again.

Connections to Camera Terminal Board

INSTALLATION

Connections to Terminal Board

Remove the terminal board cover and con-

nect the video signal cable (coaxial cable)

(× 1).

Connect the DC 12 V or AC 24 V power cables

(× 2).

In a system where the Remote Control Unit

(RM-P2580), etc. is used, connect the con-

trol signal cables (× 4).

 DC 12 V or AC 24 V power supply cable

Connect the DC 12 V or the AC 24 V power

supply to the DC 12V/AC 24V terminals on

the terminal board. To prevent connection

errors or a cable disconnection, we recom-

mend the use of lug plates for the connec-

tions.

The following table shows the connection dis-

tances and connection cables provided that

2-conductor VVF cables (vinyl-insulated vi-

nyl sheath cables) are used.

Maximum extension

(reference)

Conductor

diameter

100 m 260 m 410 m 500 m

1.0

∅

mm 1.6

∅

mm 2.0

∅

mm 2.6

∅

and more and more and more and more

Remove the terminal board

cover by flipping it up while

pushing its top to the left.

RX+ C

RX– D

A TX+

B TX–

Terminal board

Lug plates

DC 12 V or AC 24 V

power cable

To DC 12 V or AC

24 V power supply

Control signal cable

To Remote Control

Unit (RM-P2580)

To Remote Control Unit

(RM-P2580)

Video

signal cable

• Do not allow input from both a DC 12 V

and AC 24 V power supply at the same

time.

• When using a DC 12 V power supply,

ensure that the polarities of the cable are

correct.

• The AC 24 V power supply should con-

form to the following:

U-type: Class 2 only

E-type: Isolated power supply only

• Turn OFF the power supply to all components before making connections.

CAUTION:

• If thin cables are used (i.e. with a high

resistance), a significant voltage drop

will occur when the unit is at its

maximum power consumption. Either

use a thick cable to restrict the voltage

drop at the camera side to below 10%,

or place the power supply near to the

camera. If voltage drop occurs during

operation, the performance will be

unstable.

• Attach the cable conductors so that they

do not come into contact with the drop

prevention wires.

INSTALLATION

 Control signal cables

These cables should be connected only

when it is required to control the cam-

era using the RS-442A or RS-485 sig-

nals. The use of 0.65 4-conductor

twisted pair cables is recommended.

With these cables, the maximum exten-

sion distance is 1,200 m.

After having connected all of the re-

quired cables, again attach the termi-

nal board cover.

Forgetting to attach the terminal board

cover could result in accidents or

injuries.

6mm

12mm

Meshed wire

Polyethylene

Fold the meshed wire back.

Core

conductor

 Video signal cables

Connect the coaxial cables to the video

signal output terminals. Treat the tips of

the coaxial cables as shown on the left

before connection.

Note

Use the 3C-2V or 5C-2V video signal

cable (coaxial cable). The 7C-2V

cannot be used.

Connect to the

other side in

pairs like this.

A TX+

B TX-

C RX+

D RX-

Connect to the

other side in

pairs like this.

Connections to Camera Terminal Board (Continued)

Ceiling Installation

Make a hole (75 mm diameter) in the

ceiling for passing the connection

cables, and attach the provided ceiling

mount to the ceiling.

Coincide the center of the mount with

the hole (75 mm diameter) for passing

the cables through the ceiling. Attach the

ceiling mount to the ceiling using 4

screws.

Pass the wired terminal board through

the hole in the center of the ceiling

mount and leave if hanging down.

• Use M4 screws or bolts for attaching

the ceiling mount.

• If wood screws are used, use screws

with a diameter of 4.1 mm.

• The screw head height should be no

more than 4 mm.

Attach the wired terminal board to the

camera.

1) Slide the tab on the terminal board

into the guide on the camera. When

the terminal board is moved in the

direction of the arrow, it is secured to

the camera.

2) Connect the connector cable from

the camera body to the connector on

the terminal board.

Attach the drop prevention wire.

As shown in the illustration, pull the drop

prevention wire out from the ceiling

mount and attach it to the drop preven-

tion wire hook on the underside of the

camera body.

CAUTION

Be sure to attach the drop prevention wire.

If not attached, the camera body could

drop down.

Drop prevention

wire hook

Ceiling mount

bracket

φ75

Screws

Tab

Guide

Connector

cable

Drop prevention wire

Mount the camera body.

1) Ensure that the camera clamping

screw on the ceiling mount is

loosened.

2) Align the camera position alignment

mark on the camera body with the

camera position alignment mark on

the ceiling mount and press the

camera body straight against the

mount.

Note

Exercise caution when mounting so as not

to pinch the drop prevention wire and the

connected cables.

3) Rotate the camera body clockwise as

far as it will go.

At this point, check that the camera

body clamp is located on the lock

screw on the ceiling mount.

4) Tighten the camera clamping screw.

CAUTION

Be sure to tighten the camera clamping

screw fully. Otherwise the camera body

may vibrate or drop from the ceiling.

To dismount the camera from the ceiling,

perform steps

in reverse order.

Rotate the

camera body

clockwise

Camera clamping

screw

Camera

clamping screw

Camera

clamping screw

Tighten the camera

clamping screw.

(1)

(2)

(3)

(2) Position alignment mark

(2) Camera position

alignment mark

Clamp

(4)

Ceiling Installation (Continued)

INSTALLATION

Adjusting the Camera Angle

Remove the dome cover.

Rotate the dome cover counterclockwise and

pull it off.

 Horizontal rotation

(adjustable range: 90°)

Loosen the horizontal LOCK screw.

Holding the both tilt lock screws, rotate

horizontally.

Tighten the horizontal LOCK screw.

 Vertical rotation

(adjustable range: 130°)

Loosen the tilt lock screws.

Holding the rotation levers, rotate

vertically.

Tighten the tilt lock screws.

 Image inclination

(adjustable range: 30°)

Manipulate the rotation levers to adjust the

inclination of the image.

 Adjusting the image size

Adjust the size using the zoom ring.

 Adjusting the focus

Adjust using the focus ring.

When required, the surveillance image

should be adjusted, etc. This adjustment

is performed using the setup screen.

MONITOR

LOCK

LEFT RIGHT

SET

AWC

DOWN

NOT USED

L/L

INT

OFF

TERMINATION

Horizontal LOCK

screw

Dome

cover

Camera head

Rotation levers

Tilt lock screws

Focus ring

Zoom ring

2.2.

CAUTION

Be sure that the dome cover is firmly at-

tached. Improper attachment could result

in the cover dropping down.

Attach the dome cover.

Align the notch in the dome cover with

the triangle mark and push the cover

onto the camera body.

Rotate the cover clockwise as far as it

will go and is seated firmly.

Notch

Triangle mark

Adjusting the Camera Angle (Continued)

INSTALLATION

La pagina sta caricando ...

JVC Security Camera TK-C553 Manuale utente

Marca: JVC

Modello: Security Camera TK-C553

Categoria: Telecamere di sicurezza

Tipo: Manuale utente

Questo manuale è adatto anche per

Scarica il pdf

rapporto

in altre lingue

English: JVC Security Camera TK-C553 User manual

JVC Security Camera TK-C553 Manuale utente

Questo manuale è adatto anche per

JVC Security Camera TK-C553 Manuale utente

in altre lingue

Documenti correlati

Altri documenti