CYR1207-B < 1 > CYR1207-B < 2 > CYR1207-B < 3 > CYR1207-B < 4 >
Thank you for buying this Pioneer product. Please read through these instructions so
you will know how to operate your model properly. After you have finished reading the
instructions, keep this document in a safe place for future reference.
Always read and follow the “Safety Precautions” described in this manual when in-
stalling this product in a vehicle. There is a risk of accident and injury if this product is
installed using methods other than those described in this manual, or if parts are used
other than those described in this manual. P
ioneer Corporation accepts no responsibility
whatsoever in these cases.
© 2017-2018 PIONEER CORPORATION.
All rights reserved.
< KNGZ18B >< CYR1207-B >
Owner’s Manual
DASH CAMERA
ND-DVR100
Safety Precautions
Always observe the precautions described here to pre-
vent harm to yourself and others and to prevent damage
to property before it happens.
Internal Rechargeable Lithium-ion Battery
This device uses an internal rechargeable lithium
ion battery that should last the lifetime of the
device. If you suspect your battery may be dead,
try charging it several times. If the battery does not
recharge, please consult Pioneer support.
Important safeguards
WARNING
⨋
Do not install this product in your vehicle if its
location or use would obstruct the driver’s clear view
of the road or the operation of any vehicle airbag. It
is also the driver’s responsibility to know and comply
with the laws, rules, and regulations of the driving
location, including, for example, passenger privacy
rights, and not to use the device in any location where
its installation or use is prohibited.
⨋
The laws in your location may require you to provide no-
tice to passengers that a recording device is in use. If so,
you should place the notice sticker in a location clearly
visible to your passengers.
⨋
Any obstruction of or other interference with the air-
bag, either deployed or non-deployed, or with the clear
view of the road must be avoided and, accordingly,
professional installation is required.
⨋
We recommend that this product be set up and
installed by a technician who has special training and
experience in mobile electronics.
Important safety information
WARNING
⨋
Do not allow this product to come into contact with
liquids. Electrical shock could result. Also, damage
to the product, smoke, and overheating could result
from contact with liquids.
⨋
If liquid or foreign matter should get inside this prod-
uct, park your vehicle in a safe place, turn the ignition
switch off (ACC OFF) and unplug the cigarette lighter
plug immediately, and consult your dealer or the nearest
authorized Pioneer Service Station. Do not use this prod-
uct in this condition because doing so may result in a
fire, electric shock, or other failure.
⨋
If you notice smoke, a strange noise or odor from
this product, or any other abnormal signs on the LCD
screen, turn off the power immediately and consult
your dealer or the nearest authorized Pioneer Service
English
Declaration of Conformity with regard to the Radio Equipment Directive 2014/53/EU
Manufacturer:
Pioneer Corporation
28-8, Honkomagome 2-chome, Bunkyo-ku,
Tokyo 113-0021, JAPAN
EU Representative's & Importer:
Pioneer Europe NV
Haven 1087,Keetberglaan 1,9120 Melsele,Belgium
http://www.pioneer-car.eu
[*] ND-DVR100
English:
Hereby, Pioneer declares that the radio equipment
type [*] is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is
available at the following internet address:
http://www.pioneer-car.eu/compliance
Suomi:
Pioneer vakuuttaa, että radiolaitetyyppi [*] on direk-
tiivin 2014/53/EU mukainen.
EU-vaatimustenmukaisuusvakuutuksen täysimit-
tainen teksti on saatavilla seuraavassa internetosoit-
teessa:http://www.pioneer-car.eu/compliance
Nederlands:
Hierbij verklaar ik, Pioneer, dat het type radioappa-
ratuur [*] conform is met Richtlijn 2014/53/EU.
De volledige tekst van de EU-conformiteitsverklaring
kan worden geraadpleegd op het volgende interne-
tadres:http://www.pioneer-car.eu/compliance
Français:
Le soussigné, Pioneer, déclare que l'équipement
radioélectrique du type [*] est conforme à la direc-
tive 2014/53/UE.
Le texte complet de la déclaration UE de conformité
est disponible à l'adresse internet suivante:
http://www.pioneer-car.eu/compliance
Svenska:
Härmed försäkrar Pioneer att denna typ av radiout-
rustning [*] överensstämmer med direktiv 2014/53/EU.
Den fullständiga texten till EU-försäkran om över-
ensstämmelse finns på följande webbadress:
http://www.pioneer-car.eu/compliance
Dansk:
Hermed erklærer Pioneer, at radioudstyrstypen [*] er
i overensstemmelse med direktiv 2014/53/EU.
EU-overensstemmelseserklæringens fulde tekst kan
findes på følgende internetadresse:
http://www.pioneer-car.eu/compliance
Deutsch:
Hiermit erklärt Pioneer, dass der Funkanlagentyp
[Bezeichnung] der Richtlinie 2014/53/EU entspricht.
Der vollständige Text der EU-Konformitätserklärung
ist unter der folgenden Internetadresse verfüg-
bar:http://www.pioneer-car.eu/compliance
Ελληνικά:
Με την παρούσα ο/η Pioneer, δηλώνει ότι ο
ραδιοεξοπλισμός [*] πληροί την οδηγία 2014/53/ΕΕ.
Το πλήρες κείμενο της δήλωσης συμμόρφωσης
ΕΕ διατίθεται στην ακόλουθη ιστοσελίδα στο
διαδίκτυο:http://www.pioneer-car.eu/compliance
Italiano:
Il fabbricante, Pioneer, dichiara che il tipo di apparec-
chiatura radio [*] è conforme alla direttiva 2014/53/UE.
Il testo completo della dichiarazione di conformità
UE è disponibile al seguente indirizzo Internet:
http://www.pioneer-car.eu/compliance
Español:
Por la presente, Pioneer declara que el tipo de equi-
po radioeléctrico [*] es conforme con la Directiva
2014/53/UE.
El texto completo de la declaración UE de conformi-
dad está disponible en la dirección Internet sigui-
ente:http://www.pioneer-car.eu/compliance
Português:
O(a) abaixo assinado(a) Pioneer declara que o
presente tipo de equipamento de rádio [*] está em
conformidade com a Diretiva 2014/53/UE.
O texto integral da declaração de conformidade está
disponível no seguinte endereço de Internet:
http://www.pioneer-car.eu/compliance
Čeština:
Tímto Pioneer prohlašuje, že typ rádiového zařízení
[*] je v souladu se směrnicí 2014/53/EU.
Úplné znění EU prohlášení o shodě je k dispozici na
této internetové adrese:
http://www.pioneer-car.eu/compliance
Eesti:
Käesolevaga deklareerib Pioneer, et käesolev
raadioseadme tüüp [*] vastab direktiivi 2014/53/EL
nõuetele.
ELi vastavusdeklaratsiooni täielik tekst on kättesaa-
dav järgmisel internetiaadressil:
http://www.pioneer-car.eu/compliance
Magyar:
Pioneer igazolja, hogy a [*] típusú rádióberendezés
megfelel a 2014/53/EU irányelvnek.
Az EU-megfelelőségi nyilatkozat teljes szövege
elérhető a következő internetes címen:
http://www.pioneer-car.eu/compliance
Latviešu valoda:
Ar šo Pioneer deklarē, ka radioiekārta [*] atbilst Direk-
tīvai 2014/53/ES.
Pilns ES atbilstības deklarācijas teksts ir pieejams
šādā interneta vietnē:
http://www.pioneer-car.eu/compliance
Lietuvių kalba:
Aš, Pioneer, patvirtinu, kad radijo įrenginių tipas [*]
atitinka Direktyvą 2014/53/ES.
Visas ES atitikties deklaracijos tekstas prieinamas
šiuo interneto adresu:
http://www.pioneer-car.eu/compliance
Malti:
B'dan, Pioneer, niddikjara li dan it-tip ta' tagħmir
tar-radju [*] huwa konformi mad-Direttiva 2014/53/UE.
It-test kollu tad-dikjarazzjoni ta' konformità tal-UE
huwa disponibbli f'dan l-indirizz tal-Internet li ġe-
j:http://www.pioneer-car.eu/compliance
Slovenčina
Pioneer týmto vyhlasuje, že rádiové zariadenie typu
[*] je v súlade so smernicou 2014/53/EÚ.
Úplné EÚ vyhlásenie o zhode je k dispozícii na tejto
internetovej adrese:
http://www.pioneer-car.eu/compliance
Slovenščina:
Pioneer potrjuje, da je tip radijske opreme [*] sklad-
en z Direktivo 2014/53/EU.
Celotno besedilo izjave EU o skladnosti je na voljo
na naslednjem spletnem naslovu:
http://www.pioneer-car.eu/compliance
Română:
Prin prezenta, Pioneer declară că tipul de echipa-
mente radio [*] este în conformitate cu Directiva
2014/53/UE.
Textul integral al declarației UE de conformitate este
disponibil la următoarea adresă internet:
http://www.pioneer-car.eu/compliance
Български:
С настоящото Pioneer декларира, че този
тип радиосъоръжение [*] е в съответствие с
Директива 2014/53/ЕС.
Цялостният текст на ЕС декларацията за
съответствие може да се намери на следния
интернет адрес:
http://www.pioneer-car.eu/compliance
Polski:
Pioneer niniejszym oświadcza, że typ urządzenia
radiowego [*] jest zgodny z dyrektywą 2014/53/UE.
Pełny tekst deklaracji zgodności UE jest dostępny
pod następującym adresem internetowym:
http://www.pioneer-car.eu/compliance
Norsk:
Herved Pioneer erklærer at radioutstyr type [*] er i
samsvar med direktiv 2014/53 / EU.
Den fullstendige teksten i EU-samsvarserklæringen
er tilgjengelig på følgende internettadresse :
http://www.pioneer-car.eu/compliance
Íslenska:
Hér með Pioneer lýsir yfir að tegund þráðlausan
búnað [*] er í samræmi við tilskipun 2014/53/ESB.
The fullur texti af ESB-samræmisyfirlýsingu er í boði
á eftirfarandi veffangi:
http://www.pioneer-car.eu/compliance
Hrvatski:
Pioneer ovime izjavljuje da je radijska oprema tipa
[*] u skladu s Direktivom 2014/53/EU.
Cjeloviti tekst EU izjave o sukladnosti dostupan je
na sljedećoj internetskoj adresi:
http://www.pioneer-car.eu/compliance
Türk:
Burada. Pioneer radyo ekipmani turunun [*] 2014/53/
EU direktiflerine uyumlu oldugunu beyan eder.
Avrupa uyumluluk beyaninin tam metni belirtilen
internet sitesinde mevcuttur :
http://www.pioneer-car.eu/compliance
PIONEER CORPORATION
28-8, Honkomagome 2-chome, Bunkyo-ku,
Tokyo 113-0021, Japan
PIONEER ELECTRONICS (USA) INC.
P.O. Box 1540, Long Beach, California 90801-1540, U.S.A.
TEL: (800) 421-1404
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium/
Belgique
TEL: (0) 3/570.05.11
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
2 Jalan Kilang Barat, #07-01, Singapore 159346
TEL: 65-6378-7888
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
5 Arco Lane, Heatherton, Victoria, 3202, Australia
TEL: (03) 9586-6300
PIONEER ELECTRONICS DE MÉXICO S.A. DE C.V.
Blvd. Manuel Ávila Camacho 138, 10 piso
Col.Lomas de Chapultepec, México, D.F. 11000
Tel: 52-55-9178-4270, Fax: 52-55-5202-3714
先鋒股份有限公司
台北市內湖區瑞光路407號8樓
電話 : 886-(0)2-2657-3588
先鋒電子（香港）有限公司
香港九龍長沙灣道909號5樓
電話 : 852-2848-6488
Precaution
Certain country and state laws may prohibit or restrict
the placement and use of this product in your vehicle.
Please comply with all applicable laws and regulations
regarding the use, installation and operation of this
product.It is the user’s responsibility in compliance
with all applicable laws and ordinance.
Information for users on collection and dis-
posal of old equipmentand used batteries
(Symbol for
equipment)
(Symbol examples for batteries)
Pb
These symbols on the products, packaging, and/or
accompanying documents mean that used electri-
cal and electronic products and batteries should
not be mixed with general household waste.
For proper treatment, recovery and recycling of
old products and used batteries, please take them
to applicable collection points in accordance with
your national legislation.
By disposing of these products and batteries correctly,
you will help to save valuable resources and prevent
any potential negative effects on human health and the
environment which could otherwise arise from inappro-
priate waste handling.
For more information about collection and recycling of
old products and batteries, please contact your local
municipality, your waste disposal service or the point of
sale where you purchased the items
These symbols are only valid in the European
Union.
For countries outside the European Union:
If you wish to discard these items, please contact
your local authorities or dealer and ask for the correct
method of disposal.
CAUTION
⨋
The graphical symbol placed on the product
means direct current.
⨋
Information to User - Alteration or modifications
carried out without appropriate authorization may
invalidate the user’s right to operate the equipment.
Information to User
⨋
FEDERAL COMMUNICATIONS COMMISSION DEC-
LARATION OF CONFORMITY
Product Name:DASH CAMERA
Model Number:ND-DVR100
Responsible Party Name: PIONEER ELECTRONICS
(USA), INC. SERVICE SUPPORT DIVISION
Address: 1925 E. DOMINGUEZ ST. LONG BEACH, CA
90810-1003, U.S.A.
Phone: 1-800-421-1404
URL: http://www.pioneerelectronics.com
⨋
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
⨋
NOTE: This equipment has been tested and found
to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of the
following measures:
—
Reorient or relocate the receiving antenna.
—
Increase the separation between the equipment
and receiver.
—
Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected.
—
Consult the dealer or an experienced radio/TV
technician for help.
The Safety of Your Ears is in Your Hands
Get the most out of your equipment by playing it at a
safe level—a level that lets the sound come through
clearly without annoying blaring or distortion and, most
importantly, without affecting your sensitive hearing.
Sound can be deceiving. Over time, your hearing “com-
fort level” adapts to higher volumes of sound, so what
sounds “normal” can actually be loud and harmful to
your hearing. Guard against this by setting your equip-
ment at a safe level BEFORE your hearing adapts.
ESTABLISH A SAFE LEVEL:
⨋
Set your volume control at a low setting.
⨋
Slowly increase the sound until you can hear it com-
fortably and clearly, without distortion.
⨋
Once you have established a comfortable sound level,
set the dial and leave it there.
BE SURE TO OBSERVE THE FOLLOWING
GUIDELINES:
⨋
Do not turn up the volume so high that you can’t hear
what’s around you.
⨋
Use caution or temporarily discontinue use in poten-
tially hazardous situations.
CYR1207-B.indd 1-4 2018/02/06 15:27:48
CYR1207-B < 5 > CYR1207-B < 6 > CYR1207-B < 7 > CYR1207-B < 8 >
⨋
The storage areas on the microSD card are split
into the four areas shown in the following diagram
according to the type of recording.
Event video file storage area
Continuous video file storage area
Parking mode video file storage area
Photo file storage area
You can change the percentage of space used by
these storage areas.
→
“System” - “SD card partition”
⨋
Note that files be overwritten when there is insufficient
free space in the file storage areas. We recommend
that you back up any important files you want to keep.
→
“Using this product” - “Backing Up Recorded Files”
⨋
You can view video files on your PC. However, the
video may stutter or stop depending on the perfor-
mance of the PC.
⨋
The power terminal will be extremely hot immediately
after using the cigarette lighter. The tip of the Ciga-
rette Lighter Power Cable may melt or short circuit if
it is plugged in while hot. Wait for the terminal to cool
before plugging in the Cigarette Lighter Power Cable.
⨋
Do not touch the lens with your hands. Wipe the lens
off with a soft cloth if you touch it.
Precautions When Handling the
microSD Card
CAUTION
⨋
Keep the microSD card out of the reach of small chil-
dren to prevent them from accidentally swallowing it.
⨋
To prevent data loss and damage to the microSD
card, never remove it from this product while data is
being transferred.
⨋
If data loss or corruption occurs on the microSD card
for any reason, it is usually not possible to recover the
data. Pioneer accepts no liability for damages, costs
or expenses arising from data loss or corruption.
⨋
Never insert or eject an microSD card while driving.
⨋
This product supports microSDHC cards (8 GB to 32 GB,
Class 10). Not all microSDHC cards are guaranteed to work
with this product.
⨋
Format the microSD card before using it. Do not use
a microSD card that contains other data, such as
that from a PC.
⨋
Do not eject the microSD card when it is being ac-
cessed.
The file or card may be corrupted.
⨋
Even if the microSD card is used normally, you may
no longer be able to write data to the card or erase
data from the card normally.
⨋
The service life of the microSD card is not covered
under the warranty.
⨋
The microSD card is a consumable part. We recom-
mend that you regularly replace the microSD card
with a new card. If you use the microSD card for a
long period of time, this product may no longer be
able to save data to the card correctly due to bad
sectors, or an error may occur and the card will no
longer be usable.
⨋
On rare occasions, a microSD card that is recognized by
your computer may not be recognized by this product.
In this case, depending on the problem with the mi-
croSD card, this product may be able to recognize the
card by formatting it with this product format feature
→
“System” - “Format SD card”
.
However, all files,
including protected files, saved to the microSD card will
be erased when it is formatted. Always back up the files
on the microSD card before formatting it.
⨋
Pioneer Corporation does not make any assurances that
microSD card problems will be repaired by formatting
the card. Pioneer Corporation bears no responsibility for
files that are erased from the microSD card or dam-
age that occurs from formatting the card. Format the
microSD card according to your own judgment and at
your own responsibility.
When Replacing the Fuse
Check if the fuse has blown when the power will not turn on or the battery cannot be charged even though the
included Cigarette Lighter Power Cable is connected.
Connect to
vehicle
cigarettelighter
socket
Fuse (2 A/250 V)
Remove this part.
Remove carefully.
These parts are easily lost.
When Replacing the Fuse
Twist counterclockwise to remove.
Note
When the fuse has blown, replace the fuse with a new
cartridge fuse (5.2 mm diameter/20 mm long), and
firmly tighten the tip of the plug. Always replace the
fuse with a fuse of the specified capacity (2 A/250 V).
How to read this Manual
Notation Meaning
These symbols are used to draw your attention to items you should be aware of when
using this product and items you should be aware of to maintain its performance.
Note /Notes
Notes provide useful tips and extra information about product features.
[○○]
Square brackets are used to indicate selectable items displayed on the screen.
→
“
○○○○
”
Quotation marks are used to indicate references and settings.
⨋
The illustrations and example screens used in this
manual may differ from the actual product.
⨋
The actual screens of the product may be changed
without prior notification for the purpose of improve-
ments to product performance and features.
⨋
In this manual, the microSDHC memory card is
referred to as “the microSD card” for convenience.
Usage Precautions
Precautions When Handling this
product
⨋
The driver may manually set the device to save video
to assist in the monitoring of driver performance.
⨋
There are limits to the scope of video that can be
recorded with this product (
→
“Specifications”
). First
check the video that will be recorded before using this
product.
⨋
Be careful not to infringe on the privacy of any subject
in video recorded with this product when using said
video. You are fully responsible for the use of said video.
Video recorded with this product may include personal
information, such as license plate numbers.
⨋
When this product is not fully charged immediately
after purchase and the power to this product is
stopped (the engine is turned off and the Cigarette
Lighter Power Cable is unplugged), the recording time
may be shorter or this product may not be able to
record video.
⨋
The internal battery is a consumable part. The operat-
ing time will slowly decrease as the battery is repeat-
edly charged. Contact Pioneer support if you feel that
the operating time has become too short.
⨋
If this product is used near another device that uses
GPS, such as a car navigation system, that device may
temporarily be unable to receive radio waves from GPS
satellites due to radio interference. There may also
be a negative impact on the functions of surrounding
devices.
⨋
Pioneer does not offer a data recovery service for
corrupted or deleted files.
Check the Accessories
This product × 1 Installation Bracket (attached to
this product) × 1
Cigarette Lighter
Power Cable (3.5 m / 11 ft. 6 in.) × 1
Cleaning Cloth × 1 Owner’s Manual
microSDHC Card (8 GB) × 1
SD Conversion Adapter × 1
Before Installing the Product
CAUTION
⨋
First check with the vehicle manufacturer for precautions related to the installation work when installing the prod-
uct in a vehicle equipped with airbags. Otherwise there is a risk of airbag malfunction.
⨋
Always use the included parts as specified. There is a risk of product failure if other parts are used.
⨋
Install this product in a location where it will not hinder vehicle equipment and the ability to drive the vehicle.
Installation Tips
Before Installing and Securing the Product
⨋
First, temporarily connect this product and confirm that it operates correctly, and then install it. If the product
does not operate correctly, check again if there is a mistake in the connection.
Before Applying Double-sided Tape
⨋
Clean the location where the double-sided tape will be applied.
The double-sided tape cannot be reapplied once applied and peeled off because its adhesive power will weaken.
Temporarily attach this product and carefully review the routing of the cable before applying the double-sided tape.
Installation Precautions
⨋
This product is for installation to the front windshield only. Do not install it anywhere else inside or outside of the
vehicle.
⨋
Always install this product to the specified position of the front windshield and within the specified dimensions.
⨋
Depending on the vehicle, it may not be possible to install this product to the specified position and within the
specified dimensions. Consult with your dealer or the nearest authorized Pioneer Service Station for details.
⨋
Do not cover this product or get the lens dirty.
⨋
Do not place reflective objects near the lens.
⨋
Take care when handling this product so that it does not drop and you do not touch the lens.
⨋
Recording quality may be affected if the front windshield of the vehicle is coated or has been specially treated.
⨋
This product may not be able to receive GPS signals if the front windshield of the vehicle has been specially
treated.
⨋
Check the GPS reception status indicator displayed on the screen of this product. If a GPS signal cannot be
received, this product cannot be installed in this vehicle.
→ “Using this product” - “Status Display”
⨋
Choose a working location free from dust and debris in the air.
⨋
When the temperature is low or there is condensation on the glass, turn on the heater and defroster to warm up
the window in order to prevent poor adhesion of the double-sided tape.
Disclaimer
⨋
Given the large number of variables and conditions
that can be involved in an accident, Pioneer cannot
guarantee that every accident or occurrence will
trigger the recording feature in this device.
⨋
This product features may not operate properly due to
the effects of settings, how this product is installed,
the condition of the microSD card, and driving condi-
tions (including the road conditions).
⨋
If brightly colored objects are placed on the dash-
board, they may be reflected in the front windshield
and the camera image. Do not place brightly colored
objects on the dashboard.
⨋
This product is not guaranteed to be effective as
evidence in an accident.
⨋
This product is not guaranteed to save video in all
situations.
⨋
You may not be able to recognize the conditions in the
front of the vehicle in recorded video, depending on the
ambient conditions, such as the weather and time.
⨋
LED traffic signals may appear as flashing or flicker-
ing when recorded with this product. The color may
also not be correctly identifiable. Pioneer Corpora-
tion accepts no responsibility whatsoever for these
phenomena.
⨋
This product saves video before and after an accident
occurs by detecting the impact (acceleration) with the
G-sensor (accelerometer). However, this product is not
guaranteed to save video in all situations
.
⨋
Pioneer Corporation accepts no responsibility whatsoever
for product failures or damage that occur due to the
microSD card wearing out.
⨋
Pioneer Corporation does not make any assurances that
microSD card problems will be repaired by formatting
the card. Pioneer Corporation bears no responsibility for
files that are erased from the microSD card or damage
that occurs from formatting the card. Format the mi-
croSD card according to your own judgment and at your
own responsibility.
Station. Using this product in this condition may
result in permanent damage to the system.
⨋
Do not disassemble or modify this product, as there
are high-voltage components inside which may cause
an electric shock. Be sure to consult your dealer or
the nearest authorized Pioneer Service Station for
internal inspection, adjustments or repairs.
Before using this product, be sure to read and fully
understand the following safety information:
⨋
Do not operate this product if doing so will divert your
attention in any way from the safe operation of your
vehicle. Always observe safe driving rules and follow
all existing traffic regulations. If you experience diffi-
culty in operating this product or reading the display,
park your vehicle in a safe location and apply the park-
ing brake before making the necessary adjustments.
⨋
Never set the volume of this product so high that you
cannot hear outside traffic and emergency vehicles.
⨋
Keep this manual handy as a reference for operating
procedures and safety information.
⨋
Certain functions (such as viewing of screen and cer-
tain button operations) offered by this product could
be dangerous (possibly resulting in serious injury or
death) and/or unlawful if used while driving. Screen
display and button operation are disabled for this
product while the vehicle is moving.
To ensure safe driving
WARNING
⨋
In some countries the viewing of video image on a dis-
play inside a vehicle even by persons other than the
driver may be illegal. Where such regulations apply,
they must be obeyed.
Precautions before connecting the system
CAUTION
⨋
Firmly install this product so it does not fall off the
window. If this product is not firmly installed, it may
fall off the window while driving and cause an acci-
dent. Periodically inspect this product.
⨋
Secure all wiring with cable clamps or electrical tape.
Do not allow any bare wiring to remain exposed.
⨋
It is extremely dangerous to allow cables to become
wound around the steering column or gearstick. Be
sure to install this product, its cables, and wiring away
in such so that they will not obstruct or hinder driving.
⨋
Make sure that the cables and wires will not interfere
with or become caught in any of the vehicle’s mov-
ing parts, especially the steering wheel, gearstick,
handbrake, sliding seat tracks, doors, or any of the
vehicle’s controls.
⨋
Do not route wires where they will be exposed to high
temperatures. If the insulation heats up, wires may
become damaged, resulting in a short circuit or mal-
function and permanent damage to the product.
⨋
Do not shorten any cables. If you do, the protection
circuit (fuse holder, fuse resistor or filter, etc.) may fail
to work properly.
⨋
Never feed power to other electronic products by
cutting the insulation of the power supply cable of this
product and tapping into the cable. The current capac-
ity of the cable will be exceeded, causing overheating.
To prevent damage
WARNING
⨋
When replacing the fuse, be sure to only use a fuse of
the rating prescribed on this product.
Precautions before installation
CAUTION
Never install this product in places where, or in a
manner that:
⨋
Could injure the driver or passengers if the vehicle
stops suddenly.
⨋
May interfere with the driver’s operation of the vehi-
cle, such as on the floor in front of the driver’s seat, or
close to the steering wheel or gearstick.
⨋
To ensure proper installation, be sure to use the
supplied parts in the manner specified. If any parts
are not supplied with this product, use compatible
parts in the manner specified after you have the parts’
compatibility checked by your dealer. If parts other
than supplied or compatible ones are used, they may
damage internal parts of this product or they may
work loose and the product may become detached.
⨋
Do not install this product where it may
(i) obstruct the driver’s vision,
(ii) impair the performance of any of the vehicle’s op-
erating systems or safety features, including airbags,
hazard lamp buttons or
(
iii) impair the driver’s ability to safely operate the vehicle.
⨋
Never install this product in front of or next to the
place in the dashboard, door, or pillar from which one
of your vehicle’s airbags would deploy. Please refer
to your vehicle’s owner’s manual for reference to the
deployment area of the frontal airbags.
⨋
Consult with your nearest dealer if installation requires
drilling holes or other modifications of the vehicle.
⨋
Before making a final installation of this product, tem-
porarily connect the wiring to confirm that the con-
nections are correct and the system works properly.
⨋
Do not install this product in places subject to high
temperatures or humidity, such as:
—
Places close to a heater, vent or air conditioner.
—
Places that may be exposed to rain, such as close to
the door or on the vehicle’s floor.
Precautions for cigarette lighter plug
WARNING
⨋
When using a power supply in the vehicle, use the
dedicated cigarette lighter plug.
Using a plug other than the specified plug may result
in fire, electric shock, or product failure.
⨋
Unplug the cigarette plug after using the product and
when the product will not be used for a long period of time.
Depending on the vehicle, the cigarette socket may
not be turned off even when the engine is turned off.
For this reason, there is a risk of fire or a dead battery.
⨋
Fully insert the cigarette lighter plug. Poor contact may
occur due to vibrations while driving, resulting in an ex-
tremely dangerous situation where the unit overheats.
⨋
Regularly inspect and clean the cigarette lighter sock-
et. Foreign material inside the cigarette lighter socket,
such as ashes, may cause heat generation due to
poor contact, resulting in fire or electric shock.
CYR1207-B.indd 5-8 2018/02/06 15:27:51
CYR1207-B < 9 > CYR1207-B < 10 > CYR1207-B < 11 > CYR1207-B < 12 >
Installation
Specified Installation Position
⨋
Install this product in a vehicle and at a position that satisfies all of the following conditions.
—
A position where the lens of this product is in the area swept by the windshield wipers.
—
A position where the lens of this product is not affected by the sun visor and frit band.
—
A position where this product faces in the horizontal direction to the front and side to side.
—
A position where the Cigarette Lighter Power Cable can easily reach the socket.
⨋
This product must be slid to the left to remove it from the bracket after installation to the front windshield. If this
product is installed too close to the rear view mirror when it is installed on the right side of the rear view mirror in
a left-hand drive vehicle, you will not be able to remove it from the bracket.
Horizontal Direction
This product
Front Windshield
Ground
Installation Direction
This product
Horizontal DirectionHorizontal Direction
Installation Angle
Forward Direction
of Vehicle
Front Wind
shield
Front Wind
shield
Allowable Installation Angle: 5° to 80°
(With Lens Horizontal)
*
Install this product in a location where it will
not interfere with the driver’s field of view,
such as behind the rearview
mirror.
Drive Recorder UnitThis product
Airbag
Rearview Mirror
A Pillar
Within 20 % of Height
Range of Windshield Wipers
A Pillar
This product
IMPORTANT
Always install this product in the specified installation position to ensure a safe field of view while driving and to
achieve full performance from the product.
1 Clean the installation area of
dirt and oils using the included
cleaning cloth.
2 Install this product.
Peel off the sticker on the Installation Bracket
(①) and attach this product to the front
windshield.
Firmly push the top of the product and both
sides of the LCD (②). Never touch the surface
of the LCD.
1
Installation Bracket
2
Use extreme care as the double-sided tape
on the Installation Bracket in (①) is extreme-
ly strong, and it will be difficult to reapply the
tape once it has been applied.
3 Route the cable.
Route the Cigarette Lighter Power Cable to the
passenger seat side.
Cigarette
Lighter
Power Cable
The power terminal will be extremely hot
immediately after using the cigarette lighter.
The tip of the Cigarette Lighter Power Cable
may melt or short circuit if it is plugged in
while hot. Wait for the terminal to cool be-
fore plugging in the Cigarette Lighter Power
Cable.
4 Adjust the angle of the lens.
Note
A protective film is applied to the lens when the prod-
uct is purchased. Peel off this film.
Removing this product
The Installation Bracket is attached to this product when the product is purchased. After this product is installed in
the vehicle, remove this product from the Installation Bracket with the following steps.
1 Slide this product to the left as viewed from the LCD of this product.
Slide this product in the opposite direction of the "LOCK
" symbol.
2 Remove this product so that the hooks on the Installation Bracket disengage
from the slots on this product.
Installation Bracket Slots
Installation Bracket Hooks
Reverse the steps to reattach this product. Line up and fit together the hooks on the Installation Bracket with the
slots on this product, then slide this product to the right as viewed from the LCD (the direction indicated by the
“LOCK➡” symbol on the Installation Bracket).
Part Names
(Front)
(Back)
1
7
8
3
9
a
9
6
b
45
2
① System Indicator
② Mini USB Terminal (mini-B type)
The Cigarette Lighter Power Cable is connected
to this terminal. You can also connect this
product to your computer with a commercially
available USB cable.
③ Speaker
④ Function Buttons
⑤ Power Button/Function Button
⑥ Microphone
⑦ microSD Card Slot
⑧ Reset Button
Press this button with the tip of a ballpoint pen
to reset this product. (When the product is reset,
the power turns off. To turn the power back on,
press and hold the power button.)
⑨ Installation Bracket Slots
⑩ Lens
⑪ Indicator
The indicator is illuminated when powered.
CYR1207-B.indd 9-12 2018/02/06 15:27:54
CYR1207-B < 13 > CYR1207-B < 14 > CYR1207-B < 15 > CYR1207-B < 16 >
Inserting and Ejecting the microSD Card
Turn off the power to this product when inserting and removing the microSD card.
microSD Card Slot
Inserting the microSD Card
Hold the top edge of the microSD card, position the microSD card so that the label is facing the backside of this
product, and slowly insert it into the microSD card slot until it clicks.
Ejecting the microSD Card
Slowly push in the top edge of the microSD card until it clicks. The lock will be released. Pull out the microSD card.
Playing Files on a PC
You can play the files on the microSD card with your PC by inserting the microSD card ejected from this product into
your PC, using the included SD Conversion Adapter if necessary.
Folder and File Structure
Event
(Event video file)
Parking
(Parking mode video file)
Photo
(Photo file)
Video
(Continuous video file)
EVEN******-******.MP4
EVEN******-******.NMEA
PARK******-******.MP4
PARK******-******.NMEA
IMG******-******.JPG
FILE******-******.MP4
FILE******-******.NMEA
DEVICE.XML
(System file)
Folder File
SD Conversion Adapter
(included)
microSD Card
Notes
⨋
The file name is automatically assigned a name using the year, month, day, hours, minutes, and seconds.
⨋
Files with the extension “.NMEA” are administration files.
⨋
Files can be played on your PC by connecting this product and PC with a commercially available USB cable.
⨋
This product does not support USB 3.0.
Using this product
Before using this product, first stop the vehicle in a safe location and apply the parking brake.
This product Power
This product starts when the vehicle’s engine is turned on (ACC ON), and it automatically starts recording. (Contin-
uous recording)
The recorded video is saved to the microSD card as one file of the set increment of time, and when the microSD
card runs out of free space, the files are overwritten starting from the oldest file.
CAUTION
⨋
This product may not start when the engine is started if the internal battery is discharged or insufficiently
charged.
Start this product with the following methods when it does not start.
—
Press the power button on this product.
—
Charge this product and let it sit for about three minutes. Then unplug the plug of the Cigarette Lighter
Power Cable from the cigarette power socket and plug it back in.
Notes
Continuous recording will stop under the following circumstances.
—
When the settings menu is displayed – During event recording
—
When the power supply is stopped – When parking mode has started
■ Manually Turning the Power On and Off
To manually turn this product power on and off, press and hold the
power button for two or more seconds.
System Indicator Display
The operating status of this product is displayed with the system indicator.
System Indicator Charging Continuous Recording
Event/Parking Mode
Recording
Illuminated green
○
Illuminated red
○
Illuminated amber
○
Check this product settings for the parking mode settings. →
“This product Settings”
Function Buttons
The functions of the function buttons are indicated by the icons displayed at the bottom of the screen.
The functions of the buttons will depend on the displayed screen.
Notes
The following restrictions will occur when the product detects that the vehicle is moving faster than
approx. 15 km/h. (Only when a GPS signal can be received.)
⨋
will be hidden.
⨋
The product switches to the recording state while the settings menu screen is displayed.
■ Recording
1
2 3 4
① Power off
② Display settings menu
③ Take photo
④ Record event
Status Display
The status display shows the operating status of this product.
18:16:23
1 32
4
① Recording indicator
This icon flashes during recording.
② Current time
The time displayed here is recorded as the event
recording time.
→ “System”-“Date/Time”
③ GPS reception status
The bars are green when receiving GPS signals.
GPS signals cannot be received when the bars
are white and a red × is displayed.
④ Recording screen
Event Recording
■ Automatic Recording by Detecting
Impacts (Event Recording)
The continuous video file when an impact was detected
by this product, such as an impact with another vehicle,
is saved to the “Event” folder as an event video file. The
number of event video files and the recording time will
depend on when the impact was detected.
⨋
When the impact was detected at the beginning
of the file
When the impact was detected within 10 seconds
of the start of the continuous video file, the current
file where the impact was detected and the previous
file (continuous video file 1 and 2 in the following
diagram) are saved as the event video file.
Continuous video file 2Continuous video file 1
Impact detected
Continuous video file 2
Start recording
Within 0 to 10 seconds
⨋
When the impact was detected at the end of the file
When the impact was detected in the 9 seconds
before the end of the continuous video file, the file
will be extended by 10 seconds of recording time
and saved as the event video file. If an impact was
detected during the extended period, a subsequent
video file will be added and saved as an event video
file. Video files will be repeatedly added while the
impact continues.
Continuous video
file 1
Impact
detected
Start recording
9 secondsbefore
end of video
Extended by
10 seconds
Continuous video
file 2
⨋
When the impact was detected at a time other
than the beginning or end of the file
Only the continuous video file when the impact was
detected is saved as the event video file.
■ Manual Recording (Manual Event
Recording)
Switch to event recording by pressing the
button
during continuous recording. The recorded video is
saved to the
“Event” folder as an event video file.
This
product returns to continuous recording when event
recording ends.
Notes
⨋
Stop event recording by pressing the
button
during event recording.
⨋
The recording time can be set with
“Video Clip
Length”
.
→
“Video Recording” - “Video Clip Length”
⨋
You can also adjust the sensitivity for detecting
impacts.
→ “Video Recording” - “G-Sensor Sensitivity”
Parking Mode
Parking mode operates for a maximum of approximately
50 minutes after the power supplied to this product
stops (the engine is turned off or the cigarette power
cable is unplugged). If this product detects vibration
or the movement of people/vehicles due to changes
in the image, 20 seconds of video is recorded after the
detected event.
Notes
⨋
To use parking mode, under “Parking Mode”, set
“Parking Mode” to ON.
→ “Parking Mode” - “Parking Mode”
⨋
You can adjust the sensitivity for detecting vibration.
→ “Parking Mode” - “G-Sensor Sensitivity”
⨋
You can adjust the sensitivity for detecting the
movement of people and vehicles.
→
“Parking Mode” - “Motion Detection”
■ Settings menu
5
6 7 8
⑤ Back
⑥ Next settings screen
⑦ Previous settings screen
⑧ Confirm
Notes
The following restrictions will occur when the product detects that the vehicle is moving faster than
approx. 15 km/h. (Only when a GPS signal can be received.)
⨋
If the monitor display is set to [Always On], the recording screen and
will be hidden.
⨋
When the screen is off, the screen can be displayed by pressing any button.
CYR1207-B.indd 13-16 2018/02/06 15:27:58
CYR1207-B < 17 > CYR1207-B < 18 > CYR1207-B < 19 > CYR1207-B < 20 >
Using this product
Before using this product, first stop the vehicle in a safe location and apply the parking brake.
Taking Photos
You can take a photo by pressing the button
during continuous recording.
Backing Up Recorded Files
When the free space of the file storage areas is low,
recording proceeds by first deleting old files.
We recommend that you back up any important files you
want to keep with the following procedure.
Note
Prepare a spare microSD card in advance.
1 Replace the microSD card.
After recording a video or taking photos that you
want to back up, first stop the vehicle is a safe
location. Then turn off this product power, eject
the microSD card, and replace it with a spare
microSD card.
2 Copy or move the files to a PC.
Insert the microSD card into a PC, using the SD
card adapter if necessary.
Copy or move the videos and photo files to back
up to a suitable location on the PC.
Note
For the folder and file structure
→ “Playing Files on a PC”
Playing Recorded Files
You can play recorded video files and view photo files.
1 Press the button to open the
settings menu.
2 Press the
/ function
buttons, select [Playback], and
then press
.
Menu
Playback
Sound Recording
Parking Mode
Video Recording
1/2
3 Press the / function
buttons, select the folder, and then
press
.
Playback
Video
Event
Parking
Photo
You can select the following folders.
• Video • Event
• Parking • Photo
▼
The thumbnails of the selected folder will be displayed.
4 Press the / function
buttons, select the file to play, and
then press
.
Video
1/6
▼
The selected file will play.
Note
You can perform the following operations by pressing
the function buttons during playback.
⨋
Press
to return to the thumbnails.
⨋
Press / during video playback to
play the previous/next movie. Press and hold the
buttons to rewind or fast forward the video.
⨋
Press during video playback and a menu
will be displayed that allows you to perform the
following operations.
—
Pause:
Pauses the video. Press again to start playback.
—
Move to Event:
Moves the current video file to the event folder.
—
Delete:
Deletes the current video file.
⨋
Press / while viewing a photo to dis-
play the previous/next photo. Press
to delete
the current photo.
These settings configure this product. You can reset the settings to the default when the product is purchased.
You can also format the microSD card and check this product version information.
Note that continuous recording will stop while the setting screens are displayed.
1 Press the button to open the
settings menu.
2 Press the
/ function
buttons, select the setting, and
then press
.
Video Recording
Video Clip Length
WDR
EV
G-Sensor Sensitivity
1/2
3 Press the
/ function
buttons, select the value for the
setting, and then press
.
Video Clip Length
20 sec
1 min
3 min
▼
To complete the settings, press the
button until returning to the recording screen.
■ Configurable Features
Bold: Default setting value when the product is purchased.
Setting Details Values
Playback
Select [Video], [Event], [Parking], or [Photo] to play and delete recorded
videos and photo files. →
“Using this product” - “Playing Recorded Files”
Sound Recording
Sets whether or not to record sound around
this product when recording video files.
[ON]/[OFF]
Parking Mode
Parking Mode Sets parking mode. [ON]/[OFF]
Detection Method
Sets the combination of sensors to use for
detection.
[Both Motion & G-sensor]/
[Only G-sensor]/[Only Motion]
Auto Entry
When the product is powered but no vibrations
to the vehicle are detected for approximately
five minutes, the product will automatically
start parking mode. You can set the sensitivity
of the sensor that starts parking mode.
—
[Easy]: Parking mode starts easily.
—
[Difficult]: Parking mode does not start easily.
—
[OFF]: Turns off Auto Entry.
For low-vibration vehicles, the product may
start parking mode while driving, even when
the sensitivity is set to [Difficult]. In this case,
set Auto Entry to [OFF].
[Easy]/[Medium]/[Difficult]/
[OFF]
Motion Detection
Sets the sensitivity for detecting the
movement of people and vehicles through
changes in the image.
[Low]/[Medium]/[High]
G-Sensor
Sensitivity
Sets the sensitivity for detecting that the
vehicle has been exposed to vibrations.
[Low]/[Medium]/[High]
This product Settings
Before using this product, first stop the vehicle in a safe location and apply the parking brake.
Setting Details Values
Video Recording
Video Clip Length
Sets the recording time for one
continuous recording video file.*
1
[20 sec]/[1 min]/[3 min]
*
3
WDR(Wide
Dynamic Range)
Sets use of the feature that automatically
adjusts the image in situations where
there is a large difference between light
and dark.
[ON]/[OFF]
EV(Exposure
Value)
Sets the exposure level for adjusting
image brightness.
[－1]
～
[0]
～
[＋1]
G-Sensor
Sensitivity
Sets the sensitivity for detecting vibration
and impact during continuous recording.
[1]～[4]～[6]
Speed Stamp
Sets whether or not to display the travel
speed in the video file.
[ON]/[OFF]
Text Stamp
Sets a maximum of 12 characters that will be displayed at the bottom
right of the image when playing a video file.
System
Date/Time
Select [Use GPS time] or [Manual] and
set the date and time. When [Use GPS
time] is selected, the date and time will
be automatically set using Greenwich
Mean Time (GMT) received as a signal
from the GPS satellites. When using [Use
GPS time], set the time zone ([GMT-12:00]
to [GMT+12:00]) and Daylight Saving
Time for the region where the product will
be used. (The default setting when the
product is purchased is [GMT-06:00].)
[Use GPS time]/[
Manual
]
System Sound
Sets whether or not to output alarm
sounds and menu beeps.
[ON]/[OFF]
Volume Sets the volume when playing video files.
[1]～[3]～[5]
LCD Standby
Sets the screen to be [Always On] or the
time to display the screen.
[Always On]/
[10 sec screen off]/
[1 min screen off]/
[3 min screen off]
Language
Sets the language used to display the
screen.
[English]/[繁體中文]/[简体中
文]/[Русский]/[Nederlands]/
[Français]/[Deutsch]/[Español
Mexicano]/[ไทย]/[Bahasa
Indonesia]
Distance Unit
Sets the unit of distance/speed.
[Meter]/[Mile]
SD card partition
Sets the percentage of memory to use for
saving continuous video, events, parking
mode video, and photos.
→
“Guide to Recording Time and No. of
Photos”
[79% 10% 10% 1%]/
[59% 30% 10% 1%]
/
[Last storage 20 clips 10 clips
400 pics]
Restore to
Defaults
Restores all settings to the defaults when the product is purchased.
Version Allows you to check the version information of this product firmware.
Format SD card Formats the microSD card. All files on the card will be deleted.
*
2
*1 Approx. 20 seconds of video is recorded for parking mode videos. If vibrations or the movements of people
and vehicles are detected during recording, the recording time will be extended approx. 20 seconds at a time
up to a maximum of approx. 1 minute.
*2
If the microSD card experiences a problem, the “SD card error” screen will be displayed.
*3 In California in the United States of America, set this to 20 seconds to comply with state laws.
CYR1207-B.indd 17-20 2018/02/06 15:28:06
CYR1207-B < 21 > CYR1207-B < 22 > CYR1207-B < 23 > CYR1207-B < 24 >
Troubleshooting
Check the following information before sending the product in for repairs.
Symptom Cause Action
An error occurred during the
display and operation of the this
product .
The microcomputer in this
product is malfunctioning.
Press the reset button.
A file that should have been
saved cannot be found.
If there is insufficient space in
the storage areas of the microSD
card, the files will be overwritten
in order from the oldest files.
We recommend that you back up any
important files you want to keep.
→
“Using this product”- “Backing Up Recorded
Files”
The product makes parking mode
files when I get in and out of the
vehicle.
The vibration when people get
in and out of the vehicle and the
movement of people are being
detected.
Adjust the combination of sensors and their
sensitivity.
→
“Parking Mode” - “Detection Method”,
“G-Sensor Sensitivity”, “Motion Detection”
There are many videos where
nothing happens in the files
recorded while parked.
The sensitivity of vibration
detection and motion detection
may not be appropriate.
Adjust the combination of sensors and their
sensitivity.
→
“Parking Mode” - “Detection Method”,
“G-Sensor Sensitivity”, “Motion Detection”
My vehicle was hit while parked,
but a video file wasn’t made.
This may be due to the service
life of the battery.
Please consult with the nearest authorized
Pioneer Service Station.
An accident occurred during
driving, but a video file wasn’t made.
The sensitivity of impact
detection may not be appropriate.
Adjust the sensitivity of vibration detection.
→
“Video Recording” - “G-Sensor Sensitivity”
There’s no sound when I play a
video file.
The sound recording setting may
be OFF.
Check the sound recording setting again.
→
“Sound Recording”
Guide to Recording Time and No. of Photos
The following table provides estimates of the video recording times and number of photos possible with different
“SD card partition” settings. The actual values will depend on various factors, such as the microSD card being used,
subject being recorded, and recording conditions.
The “SD card partition” setting is expressed as follows.
Example: [79% 10% 10% 1%]
As a percentage of memory card capacity, the continuous recording time will be 79%, the event recording time will
be 10%, the parking mode time will be 10%, and the number of photos will be 1%.
Guide to Recording Time and No. of Photos with an 8 GB microSD Card
SD card partition Continuous
Recording
Event Recording Parking Mode
Recording
No. of Photos
[79% 10% 10% 1%]
Approx. 1 hours 9
minutes
Approx. 6
minutes
Approx. 7
minutes
Approx. 500
photos
[59% 30% 10% 1%]
Approx. 45 minutes Approx. 24
minutes
Approx. 7
minutes
Approx. 500
photos
Remaining capacity*1 Approx. 15 minutes 20 files 10 files 400 photos
Guide to Recording Time and No. of Photos with an 32 GB microSD Card
SD card partition Continuous
Recording
Event Recording Parking Mode
Recording
No. of Photos
[79% 10% 10% 1%]
Approx. 4 hours 47
minutes
Approx. 33
minutes
Approx. 35
minutes
Approx. 2 000
photos
[59% 30% 10% 1%]
Approx. 3 hours 35
minutes
Approx. 1 hour 48
minutes
Approx. 35
minutes
Approx. 2 000
photos
Remaining capacity*1 Approx. 5 hours 20 files 10 files 400 photos
*1 This setting saves 20 files for event recording, 10 files for parking mode recording, 400 photos, and
continuous recordings in the remaining memory.
Guide to Recording Time When Fully Charged
Parking mode standby time: Maximum of approx. 50 minutes
■ Guide to Charging Time
Approx. 3 hours
Note
The recording times are estimates. The actual recording times will depend on the scenery being recorded and
charge status of the battery.
GPS
⨋
GPS (Global Positioning System) is a system that measures your current position by receiving position measure-
ment radio signals from GPS satellites.
⨋
The GPS satellite signals cannot pass through solid matter (except glass). The signals from GPS satellites may be
blocked when this product is in the following locations.
—
Inside tunnels and parking structures
–
On the bottom level of a two-level highway
—
Around concentrations of skyscrapers
–
In a dense forest
Trademarks & Copyrights
⨋
microSDHC logo is a trademark of SD-3C, LLC.
Please Recycle the Rechargeable Battery
(For other than American and Canadian Users)
This product uses a lithium ion battery. Lithium ion batteries are a valuable resource that can be recycled. Remove
the lithium ion battery from the product when replacing the battery or disposing of the product and recycle it. Re-
move the lithium ion battery from the product with the following procedure when disposing of the product.
CAUTION
⨋
The purpose of this section is to describe how to remove the internal battery when disposing of the product. This
product warranty will be void when you open the product.
⨋
Fully discharge the internal battery before removing it to prevent short circuits. The battery still retains a charge even when
the power does not turn on. We recommend that you leave the product for a number of days before removing the battery.
⨋
Eject the microSD card before removing the battery.
⨋
Be careful not to injure yourself when disassembling the case.
1 Remove the two screws on the
bottom of this product.
Note
Remove the screws with a commercially available #0
Phillips screwdriver.
2 Release the four hooks that hold
the display side of the case.
The locations of the hooks are shown in the
following diagram.
Note
The hooks can be released with a flathead screw-
driver.
3 Disconnect the display-side
connector.
4 Disconnect the speaker connector,
and remove the four screws
holding the board.
5 Lift up the board, disconnect the
connector, and remove the battery.
CAUTION
The battery is attached with double-sided tape. If the
battery is difficult to remove, insert a flathead screw-
driver in between the battery and case to remove it.
Be careful not to damage the battery when doing so.
Specifications
Recording Medium microSDHC card, Class 10 (8 GB to 32 GB)
Imaging Element CMOS sensor, 2.07 million pixels
Recording Angles 95° horizontal, 52° vertical, 111° diagonal
F-Number F2.0
Recording Resolution Full HD (1 920 × 1 080 pixels)
GPS Built-in
G-Sensor
3-axis G-sensor (During event recording: level can be set in 6 steps/
during parking mode: level can be set in 3 steps)
Recording Methods
Continuous recording/event recording/manual event recording/
parking mode recording
Video File Structure 20 sec/1 min/3 min
Display 2-inch LCD
Sound Recording Can be set to ON or OFF
Frame Rate 27.5 fps
Compression Method
(Video)
MP4 (H.264 + ADPCM codec)
Compression Method
(Photo)
JPEG
Power Supply Voltage This product 5 VDC (includes a 12 V/24 V Cigarette Lighter Power Cable)
Power Consumption 1.8 W (2.8 W when charging)
Dimensions (W × H × D)
61 mm × 67 mm × 39.2 mm (2-3/8 in. × 2-5/8 in. 1-1/2 in.)
(This product)
Weight
87 g(1.9 lbs)
(excluding the Installation Bracket and Cigarette Lighter Power Cable,
etc.)
Operating Temperature −10 °C to +60 °C (−50 °F to +140 °F)
Internal Battery Capacity 500 mAh
Note
Specifications and design are subject to possible modifications without notice due to improvements.
WARNING/DISPOSAL OF UNIT
(For American Users, Canadian Users)
Please do NOT attempt to change the battery yourself. If the battery has died and you do not want us to replace your
battery, you should follow the disposal instructions below:
⨋
Never dispose of used batteries/electronics with ordinary solid wastes, since they contain toxic substances.
⨋
Always dispose of used batteries/electronics in accordance with the prevailing community regulations that apply
to the disposal of batteries/electronics. If there are no local regulations concerning battery/electronics disposal,
please dispose of the device in a waste bin for electronic devices.
⨋
Many electronics retailers now recycle batteries and other electronic components at no charge. Check to see
which ones in your area do so.
CYR1207-B.indd 21-24 2018/02/06 15:28:09
-
1
-
2
-
3
-
4
-
5
-
6
in altre lingue
- English: Pioneer ND-DVR100 User manual
- română: Pioneer ND-DVR100 Manual de utilizare