© RISCO Group 01/2012 5IN1749

EN 50131-1

EN 50131-2-4

Grade 2

Environmental Class II

CE Compliance Section:

Risco Ltd. hereby declares that this equipment is in compliance with the essential

requirement and other relevant provisions of Directive 1999/5/EC.

For the EC Declaration of Conformity please refer to our website: www.riscogroup.com

of production. Because Seller does not install or connect the product and because the

product may be used in conjunction with products not manufactured by the Seller, Seller

cannot guarantee the performance of the security system which uses this product. Seller's

obligation and liability under this warranty is expressly limited to repairing and replacing, at

Seller's option, within a reasonable time after the date of delivery, any product not meeting

the specifications. Seller makes no other warranty, expressed or implied, and makes no

warranty of merchantability or of fitness for any particular purpose.

In no case shall seller be liable for any consequential or incidental damages for breach of

this or any other warranty, expressed or implied, or upon any other basis of liability

whatsoever.

occurred due to any type of tampering, whether intentional or unintentional such as

masking, painting or spraying on the lenses, mirrors or any other part of the detector.

Buyer understands that a properly installed and maintained alarm may only reduce the risk

of burglary, robbery or fire without warning, but is not insurance or a guaranty that such

event will not occur or that there will be no personal injury or property loss as a result

thereof.

Consequently seller shall have no liability for any personal injury, property damage or loss

based on a claim that the product fails to give warning. However, if seller is held liable,

whether directly or indirectly, for any loss or damage arising under this limited warranty or

otherwise, regardless of cause or origin, seller's maximum liability shall not exceed the

Dispose of used batteries according to local regulations.

us through our website (www.riscogroup.com)

or at the following telephone and fax numbers:

Mounting Height L - LONG S - SHORT

2.1m-2.7m (6'11"-8’10") 15m (50’) 6m (20’)

Terminal Description

- 12 + 12VDC Input

ALARM N.C. Relay

TAMPER N.C. Tamper switch

LED LED operation remote control

When an ”Activation Signal”** is applied to the LED input

terminal, all LEDs will be disabled.

0V is applied and LED Input Jumper is on 0V position

Jumper Settings

SW1-2: ACT Used to determine if ACT mode is enabled or disabled

ON

OFF

Walk Test

1. Two minutes after applying power (warm-up period), walk test the

Detector over the entire protected area to verify proper operation of the

unit (see Figure 7).

2. The K-Band MW range must be adjusted using the potentiometer located

on the PCB. It is important to set the potentiometer to the lowest possible

setting that will still provide enough coverage for the inner boundary

protected area (see Figure 5).

Flashing Trouble in PIR channel

Flashing Trouble in MW channel

Technical Specification

Electrical

Current consumption 16mA at 12VDC (typical)

Voltage requirements 9 -16VDC***

Optical

Filtering White Light Protection

Physical

*** Power to be supplied by 5A max. power source using safety approved

wires, with a min Gauge of 20AWG.

(Default)

.

The BWare DT detector is the ultimate motion detector for professional

built-in end-of-line (EOL) resistors to simplify installation.

The detector employs K-Band microwave providing reduced wall

posizione 12V (posizione di default)

- Viene applicato un riferimento di alimentazione 0V e il ponticello LED

Input è nella posizione 0V

Prova di movimento (Walk Test)

1. Due o tre minuti dopo aver alimentato il rivelatore (inizializzazione)

effettuare la prova di copertura dell’area da proteggere verificando la

risposta del rivelatore tramite l’accensione dei LED (vedere Figura 7).

2. La portata della microonda va regolata tramite l’apposito potenziometro

situato sulla scheda elettronica. Regolare il potenziometro della

microonda al minimo possibile riferito all’area da proteggere

una penetrazione ridotta attraverso i muri.

J4- LED Usato per impostare la polarità dei comandi di attivazione

Microint./Pontic. Funzione

Predisposizione microinterruttori e ponticelli

Predisposizione microinterruttori e ponticelli

Microint./Pontic. Funzione

SW1-2: ACT Usato per abilitare o disabilitare la funzione ACT.

ACT abilitato

Importante: Non usare la funzione ACT™ se nel luogo di

OFF

ON

OFF

(Default)

Nota: Quando la funzione Green Line è attiva (Microonda

infrarossi (PIR).

OFF

(Default)

J1 - Alarm EOL

J2 - Tamper EOL

(Default)

Contains FCC ID UXS-IPM165F

BWare RK515DTGL FCC Compliance Section:

FCC Part 15 Note:

This equipment has been tested and found to comply with the limits for a Class B digital

If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment to an outlet on a circuit different from that to which the

receiver is connected.

 Consult the dealer or an experienced radio/TV technician.

FCC Warning:

The manufacturer is not responsible for any radio or TV interference caused by

**Signal d'Activation-

Si une tension de 12VCC est appliquée et que le Cavalier d'entrée LED

est en position 12V (Défaut de position)

-Ou-

Si la Terre (GND) est reliée, le Cavalier d'entrée LED est en position 0V.

SW1-3: Green Line

Le BWare DT intègre la fonction Green Line, qui suit les recommandations

Note : Quand le Green Line est activé (HF désactivé), le

détecteur sera toujours actif (IRP seul).

Arrêt (OFF)

Cavalier Fonction

SW1-2: ACT Définit si le mode ACT est activé ou non

ACT activé.

Important ! N'utilisez pas le mode ACT™ dans une zone en

paraît logique et attendu, un couloir par exemple.

Arrêt (OFF)