ProLights SMARTOWERPACK Manuale utente

USER MANUAL

MANUALE UTENTE

SMARTOWER

SMARTOWERPACK

LED BATTERY LIGHTING

EN - IT

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the

characteristics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

REV. 01-10/20

1

SMARTOWER - SMARTOWERPACK

TABLE OF CONTENTS

Safety

General instructionsGeneral instructions

Warnings and installation precautionsWarnings and installation precautions

1 Introduction

1. 1 Technical drawing 1. 1 Technical drawing

1. 2 SMARTOWERPACK (optional)1. 2 SMARTOWERPACK (optional)

1. 3 Operating elements and connections1. 3 Operating elements and connections

2 Installation

2. 1 Mounting2. 1 Mounting

3 Functions and settings

3. 1 Operation3. 1 Operation

3. 2 Basic3. 2 Basic

3. 3 Recharge Process3. 3 Recharge Process

3. 4 Menu structure3. 4 Menu structure

3. 5 DMX conguration3. 5 DMX conguration

3. 6 DMX mode 3. 6 DMX mode

3. 7 Display settings3. 7 Display settings

3. 8 WIFI function3. 8 WIFI function

3. 9 Controller IR3. 9 Controller IR

3. 10 Fixture information 3. 10 Fixture information

3. 11 Presents3. 11 Presents

3. 12 Auto3. 12 Auto

3. 13 Pattern 3. 13 Pattern

3. 14 Manual mode3. 14 Manual mode

3. 15 DMX Control3. 15 DMX Control

Battery Guide

2

3

4

5

6

7

8

9

10

11

12

13

16

Packing content

SMARTOWER:

• SMARTOWER

• M10 ring for security

cable

• Single charger

• IR controller

• User manual

SMARTOWERPACK:

• 6 pz SMARTOWER

• Flight case with integrated battery

charger kit

• IR controller

• PowerCON powercable

• User manual

SMARTOWER - SMARTOWERPACK

2

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

SAFETY

General instruction

• The products referred to in this manual conform to the European Community Directives and are there-

fore marked with .

• The unit is supplied with hazardous network voltage. Leave servicing to skilled personnel only. Never

make any modications on the unit not described in this instruction manual, otherwise you will risk an

electric shock.

• Connection must be made to a power supply system tted with ecient earthing (Class I appliance ac-

cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units

from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• The connection to the main network of electric distribution must be carried out by a qualied electrical

installer. Check that the main frequency and voltage correspond to those for which the unit is designed

as given on the electrical data label.

• This unit is not for home use, only professional applications.

• Never use the xture under the following conditions:

- in places subject to vibrations or bumps;

- in places with an ambient temperature of over 40°C.

• Make certain that no inammable liquids, water or metal objects enter the xture.

• Do not dismantle or modify the xture.

• All work must always be carried out by qualied technical personnel. Contact the nearest sales point for

an inspection or contact the manufacturer directly.

• If the unit is to be put out of operation denitively, take it to a local recycling

plant for a disposal which is not harmful to the environment.

Warnings and installation precautions

• If this device will be operated in any way dierent to the one described in this manual, it may suer

damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like

short circuit, burns, electric shock, etc.

• Before starting any maintenance work or cleaning the projector, cut o power from the main supply.

• Always additionally secure the projector with the safety rope. When carrying out any work, always com-

ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country

in which the xture’s being used.

• Install the xture in a well ventilated place.

• Keep any inammable material at a safe distance from the xture.

• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent

that their eectiveness is impaired.

• The lamp (LED) shall be changed if it has become damaged or thermally deformed.

• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ashing light, may

trigger epileptic seizures in photosensitive persons or persons with epilepsy.

• Do not touch the product’s housing when operating because it may be very hot. After power o, please

cool down over 15 minutes.

• This product was designed and built strictly for the use indicated in this documentation. Any other use,

not expressly indicated here, could compromise the good condition/operation of the product and/or

be a source of danger.

• We decline any liability deriving from improper use of the product.

3

SMARTOWER - SMARTOWERPACK

- 1 - INTRODUCTION

1.1 TECHNICAL DRAWING

Technical drawing Fig.1

632

Ø119

SMARTOWER - SMARTOWERPACK

4

1.2 SMARTOWERPACK (optional)

The pack includes:

• 6 pcs SMARTOWER

• 1 Flight case with integrated battery charger kit

• 1 IR controller

• 1 PowerCON powercable

NOTE

Always charge with

ight-case open

671

600 600

117

788

Fig.2

Technical drawing

5

SMARTOWER - SMARTOWERPACK

1.3 OPERATING ELEMENTS AND CONNECTIONS

Fig.3

1. ON/OFF SWITCH

2. IR RECEIVER SIGNAL

3. CONTROL PANEL with LCD display and 4

button used to access the control panel

functions and manage them.

4. TOP COVER

5. HOLE for tripode stand.

6. Base for recharge operations through

magnetic charge in case.

7. HOLE for secutity cable.

1

2

4

7

6

5

3

SMARTOWER - SMARTOWERPACK

6

1005 mm

39.57 in

1610 mm

63.38 in

CLAMP

SECURITY

CABLE

2.1 MOUNTING

The SMARTOWER can be placed on a solid plane. Moreover, thanks to the (optional) extendable stand,

it can exceed a height of 1.6m (g.4). As you can see in the illustration, you have to insert the coupling

system in the appropriate seat of the plate where it is locked with a clockwise rotation (until the stop).

Always ensure that the unit is rmly xed to avoid vibration and slipping while operating. The mounting

place must be of sucient stability and be able to support a weight of 10 times of the unit’s weight. When

carrying out any installation, always comply scrupulously with all the regulations (particularly regarding

safety) currently in force in the country in which the xture’s being used.

- 2 - INSTALLATION

Fig.4

7

SMARTOWER - SMARTOWERPACK

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

Switch on the SMARTOWER with the power switch. The unit is ready for operation and can be operated via

a DMX controller or it independently performs its show program in succession.

After operation, switch o the unit with the power switch.

3.2 BASIC

The SMARTOWER has a OLED display and 4 button used to access the control panel functions and manage

them (g.5).

3.3 RECHARGE PROCESS

To recharge the SMARTOWER, use the Flight-case or use the IP connector for the quick magnetic charger.

Fig.5 - Functions of the buttons

MODE / ESC

UP DOWN ENTER

Used to access the menu or

to return a previous menu

option

Navigates downwards through

the menu list and increases

the numeric value when in a

function

Navigates upwards through

the menu list and decreases

the numeric value when in

a function

Used to select and store the

current menu or conrm the

current function value or

option within a menu

MODE

/ ESC

UP DOWN ENTER

SMARTOWER - SMARTOWERPACK

8

3.4 MENU STRUCTURE

MENU

1 CONTROL

ð

Address

ð

W-DMX

ð

Value (1-512)

DMX Mode

ð

Mode

ð

8CH/15CH/18CH

Defautl:

18CH

Wireless

ð

Reset Connect

ð

YES/NO Defautl: No

2 SET

ð

Screen

ð

Backlight

ð

O-99m (02m)

Defautl:

02m

Flip Display

ð

YES/NO Defautl: No

Adjust

ð

Shutter...

3 ADVANCED

ð

Reload Default

ð

Basic Reload

ð

ON/OFF Defautl: O

Program Reload

ð

ON/OFF Defautl: O

Password

ð

050 (unlocks the following settings)

Private Reload

ð

ON/OFF Defautl: O

All Reload

ð

ON/OFF Defautl: O

4 INFORMATION

ð

Software Ver.

ð

1U01 V1.0.00…

5 STATIC

ð

Presets

ð

Red

Deep Orange

Light Orange

Yellow

Green

Sea Green

Aquamarine

Cyan

Blue

Violet

Purple

Magenta

White

Auto Value (1~25)

Pattern Value (1~25)

Manual Shutter

ð

Value (0~255)

9

SMARTOWER - SMARTOWERPACK

3.5 DMX ADDRESSING

To enter the DMX mode, follow these steps:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select Control, then press the ENTER button to enter the

next menu.

• Press the UP/DOWN button to scroll through the menu, select the DMX Address and press the ENTER key.

• Press the arrow keys to select the desired value (001-512). Press the ENTER key to conrm the setting.

• Press the ESC button repeatedly to exit the menu and save changes.

For operation via light control unit with DMX512 protocol, is sucient connect the controller to SMARTOW-

ER. To able to operate the SMARTOWER with a light controller, adjust the DMX start address for the rst a

DMX channel. If e. g. address 33 on the controller is provided for controlling the function of the rst DMX

channel, adjust the start address 33 on the SMARTOWER. The other functions of the light eect panel are

then automatically assigned to the following addresses.

An example with the start address 33 is shown at the below image (g.6).

3.6 DMX MODE

The SMARTOWER has 3 DMX channel congurations which can be accessed from the control panel.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select Control, then press the ENTER button to enter the

next menu.

• Press the UP/DOWN button to scroll through the menu, select DMX Mode and press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Mode and press ENTER to conrm your

choice.

• Use the UP/DOWN button to select the desired DMX channel conguration (8CH, 15CH, 18CH), then press

the ENTER button to conrm your choice.

• Press the ESC button to go back or to meet the waiting time to exit the setup menu.

Fig.6 - Example 18 DMX channels conguration

DMX Address: 87DMX Address: 51DMX Address: 33 DMX Address: 69

. . . . . . . . . . . .

DMX512 Controller

Number of

DMX

channels

Start address

(example)

DMX Address

occupied

Next possible start

address for unit No. 1

Next possible start

address for unit No. 2

Next possible start

address for unit No. 3

8 33 33-40 41 49 57

15 33 33-47 48 63 78

18 33 33-50 51 69 87

SMARTOWER - SMARTOWERPACK

10

Fig.7

DMX512 Controller

wireless

solution

3.7 DISPLAY SETTINGS

You can change the following parameters related to the display, following the same procedure:

• Press the ENTER button to access the main menu.

• Press the UP / DOWN keys to scroll the menu, select the Set icon, then press the ENTER button to enter

the next menu.

• Press UP / DOWN to scroll through the menu, then select Screen, and press the ENTER button to enter

the next menu.

• Press UP / DOWN to scroll through the menu, and then select one of the following settings for the dis-

play and press the ENTER key to display it.

- Back Light - Backlight display Auto O. This feature allows you to automatically turn o the backlight

after a specied time that you can set using the arrow buttons. To have the display always on select

Always On or set a value of 01-99 min to turn o the display after the amount of time you choose.

- Flip Display - Orientation of the display. This function allows you to rotate the display 180° to get a

better view of the display when the unit is hanging upside down. Select ON to activate or OFF to

disable this function.

• Press the ENTER button to conrm your choice.

• Press the ESC button to go back or to meet the waiting time to exit the setup menu.

3.8 WIFI FUNCTION

To enable wireless control mode, proceed as follows:

• Press the UP/DOWN button to scroll the menu, select Control, then press the ENTER button to enter the

next menù.

• Press theUP/DOWN button to select Wireless then press the ENTER button to store.

• Select Reset Connect to reset the unit and press the ENTER button to store.

• Press the ESC button to go back or to meet the waiting time to exit the setup menu.

11

SMARTOWER - SMARTOWERPACK

Fig.8

3.9 CONTROLLER IR

Make sure to point the controller directly at the IR receiver near the switch to turn on/o the SMARTOWER.

Use the keys as below to access the functions.

FADE

SOUND

SENSIT.

AUTO

MACRO

POWER

STROBESPEEDDIMMERMANUAL

AMBER

UV

RED

YELLOW

CYAN

MAGENTA

STATIC

DEEP

ORANGE

LIGHT

ORANGE

SEA

GREEN

AQUA

MARINE

WARM

WHITE

COLD

WHITE

GREEN

BLUE VIOLET PURPLE

WHITE

FUNCTION ISTRUCTIONS

POWER

(POWER ON/OFF)

Press this button for one time, the xture will be power on and all

LED will be red.The xture will be power o if you press it twice.

STROBE

(STROBE ON/OFF)

After pressing button “STROBE”,you can chose the strobe mode by

using button “UP” or “DOWN”.

SPEED

(SPEED ADJUST)

1.At STROBE mode, you can adjust the strobe speed by using button

"UP" or "DOWN".

2.At AUTO mode, you can adjust the auto speed by using button

“UP” or “DOWN”.

DIMMER Can adjust the brightness by using button “UP” or “DOWN”.

MANUAL

(COLOR ADJUST

MANUAL)

Can choose RGB by pressing button “MANUAL”,and then using “UP”

or “DOWN” to adjust the color.

RED

Can adjust the color by using “UP” or “Down”,while it cann’t adjust

the color in STATIC mode.

GREEN

BLUE

STATIC Can choose the color by pressing the button “STATIC”.

DEEP ORANGE

LIGHT ORANGE

…

COLD WHITE

AUTO

Press button “AUTO” for one time, can choose the eect by “UP” or

“DOWN”. The eect can be moving reversely by pressing button

“AUTO” twice.

FADE

Press this button,fade is working and can adjust the fade eect by

using button “UP” or “DOWN”.

SMARTOWER - SMARTOWERPACK

12

3.10 FIXTURE INFORMATION

To view all the information on the device, proceed as follows:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the icon Information, then press the ENTER button

to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, then select Software Version to display the cur-

rently installed software version and press the ENTER button to display it.

• Press the ESC button to go back or to meet the waiting time to exit the setup menu..

3.11 PRESETS

The unit has preset pre-programmed colors that can be set through the following procedure:

• Press the UP/DOWN button to scroll the menu, select Static, then press the ENTER button to enter the

next menù.

• Select Presets throught the UP/DOWN button, then press the ENTER button to conrm.

• Set the color (Red, Deep Orange, Light Orange, Yellow, Green, Sea Green, Aquamarine, Cyan, Blue, Violet, Purple,

Magenta, White) throught the UP/DOWN button, then press the ENTER button to conrm.

• Press the ESC button to go back or to meet the waiting time to exit the setup menu.

3.12 AUTO

The unit has automatic pre-programmed show that can be set through the following procedure:

• Press the UP/DOWN button to scroll the menu, select Static, then press the ENTER button to enter the

next menù.

• Select Auto throught the UP/DOWN button, then press the ENTER button to conrm.

• Set the value (1~25) throught the UP/DOWN button, then press the ENTER button to conrm.

• Press the ESC button to go back or to meet the waiting time to exit the setup menu.

3.13 PATTERN

The unit has automatic pattern that can be set through the following procedure:

• Press the UP/DOWN button to scroll the menu, select Static, then press the ENTER button to enter the

next menù.

• Select Pattern throught the UP/DOWN button, then press the ENTER button to conrm.

• Set the value (1~25) throught the UP/DOWN button, then press the ENTER button to conrm.

• Press the ESC button to go back or to meet the waiting time to exit the setup menu.

3.14 MANUAL

This function allows you to create your own customized stand alone, using the following parameters:

Shutter, Dimmer, Dimmer Fade, Color Function, Virtual Color1, Virtual Color2, Red all, Green all, Blue all, Pattern, Pattern

speed, Pattern Dimmer Transition, Foreground, Foreground dimmer, Foreground shutter, Background, Background dimmer,

Background Shutter.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Static icon, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Manual and press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to select one of the parameters and press ENTER to edit the value (000-255)

through the UP/DOWN button. Press the ENTER button to conrm your choice and then press the ESC

button repeatedly to exit the menu and save changes.

13

SMARTOWER - SMARTOWERPACK

3.15 DMX CONTROL

CHANNEL

FUNCTION

DMX

Value

8CH 15CH 18CH

1 1 1

LED STRIP SHUTTER

Shutter closed

Strobe eect slow to fast

No function (shutter open)

Pulse-eect in sequences

No function (shutter open)

Random strobe eect slow to fast

No function (shutter open)

000 - 010

011 - 082

083 - 093

094 - 163

164 - 174

175 - 244

245 - 255

2 2 2

LED STRIP DIMMER

Dimmer 0% ~ 100%

000 - 255

3 3

LED STRIP DIMMER FADE OUT

0% to 100%

000 - 255

3 4 4

LED STRIP VIRTUAL COLOR FUNCTION

On Function

White presets Function

Forward Spin

Reverse Spin

Continuous

Color Bounce

TBD

000 - 015

016 - 031

032 - 047

048 - 063

064 - 079

080 - 111

112 - 255

4 5 5

LED STRIP VIRTUAL COLOR1

White presets Function

White 2000K ~ 2700K

White 2700K ~ 3200K

White 3200K ~ 4200K

White 4200K ~ 5600K

White 5600K ~ 8000K

White 8000K ~ 10000K

Forward Spin

Rainbow Eect (Slow->Fast)

Reverse Spin

Rainbow Eect (Slow->Fast)

Continuous & Color Bounce

Black

Red

Green

Blue

White

Red=0, Green->up,Blue=full,White=0

Red=0, Green=full,Blue->down,White=0

Red->up, Green=full,Blue=0,White=0

Red=full, Green->down,Blue=0,White=0

Red=full, Green=0,Blue->up,White=0

Red->down, Green=0,Blue=full,White=0

000 - 042

043 - 085

086 - 128

129 - 171

172 - 214

215 - 255

000 - 255

000

001

002

003

004

005 - 046

047 - 088

089 - 130

131 - 172

173 - 214

215 - 255

SMARTOWER - SMARTOWERPACK

14

CHANNEL

FUNCTION

DMX

Value

8CH 15CH 18CH

5 6 6

LED STRIP VIRTUAL COLOR2 (Only On Color Bounce)

Black

Red

Green

Blue

White

Red=0, Green->up,Blue=full,White=0

Red=0, Green=full,Blue->down,White=0

Red->up, Green=full,Blue=0,White=0

Red=full, Green->down,Blue=0,White=0

Red=full, Green=0,Blue->up,White=0

Red->down, Green=0,Blue=full,White=0

000

001

002

003

004

005 - 046

047 - 088

089 -130

131 - 172

173 - 214

215 - 255

6 7

LED STRIP RED

0~100%

000 - 255

7 8

LED STRIP GREEN

0~100%

000 - 255

8 9

LED STRIP BLUE

0~100%

000 - 255

7 10

LED STRIP PATTERN

On Pattern

Pattern control

Pattern Eect

Random Pattern Eect

000 - 015

016 - 031

032 - 176

177 - 255

8 11

LED STRIP PATTERN SPEED

Pattern control

Picture Eect 1-250

Pattern Eect & Random Pattern Eect

Static indexing

Forward Slow to fastest

Stop

Reverse Slow to fastest

000 - 255

000 - 023

024 -137

138 - 141

142 - 255

9 12

LED STRIP DIMMER TRANSITION

Dimmer 0% ~ 100%

000 - 255

10 13

LED STRIP FOREGROUND

No Function

Foreground Color

000 - 003

004 - 255

11 14

LED STRIP FOREGROUND DIMMER

Dimmer 0% ~ 100%

000 - 255

12 15

LED STRIP FOREGROUND SHUTTER

Shutter closed

Strobe eect slow to fast

No function (shutter open)

Random strobe eect slow to fast

No function (shutter open)

000 - 010

011 - 163

164 - 174

175 - 244

245 - 255

15

SMARTOWER - SMARTOWERPACK

CHANNEL

FUNCTION

DMX

Value

8CH 15CH 18CH

13 16

LED STRIP BACKGROUND

No Function

Foreground Color

000 - 003

004 - 255

14 17

LED STRIP BACKGROUND DIMMER

Dimmer 0% ~ 100%

000 - 255

15 18

LED STRIP BACKGROUND SHUTTER

Shutter closed

Strobe eect slow to fast

No function (shutter open)

Random strobe eect slow to fast

No function (shutter open)

000 - 010

011 - 163

164 - 174

175 - 244

245 - 255

SMARTOWER - SMARTOWERPACK

16

Battery Guide

New Lithium Battery Initialisation

Any new xture containing a Lithium battery should be initialised when rst purchased to maximise its battery life.

To do this:

1. Fully charge the unit for a minimum of 5 to 6 hours.

2. Fully discharge, then fully recharge the battery.

3. Repeat this cycle another 2 times for optimum battery life.

Maximizing Battery Performance

1. Lithium batteries perform best when in regular use. Long idle periods will reduce the battery life.

2. Recharge the battery at the earliest opportunity, leaving batteries discharged for long periods will reduce battery life.

3. Store units containing Lithium batteries at cool temperatures. High ambient temperatures signicantly reduce the life

of a Lithium battery.

4. Disconnect power from the unit when charging is complete.

5. Do not use xtures whilst charging.

Long term storage

1. Charge your xture’s battery to around 50%. If you store a xture with a fully discharged battery, it could fall into a

deep discharge state. If you store it fully charged, the battery may lose some capacity, leading to shorter battery life.

2. Power down the device to avoid additional battery use.

3. Place your device in a cool, moisture-free environment that’s less than 32° C (90° F).

Music & Lights S.r.l. si riserva ogni diritto di elaborazione in qualsiasi forma delle presenti istruzioni per l’uso.

La riproduzione - anche parziale - per propri scopi commerciali è vietata.

Al ne di migliorare la qualità dei prodotti, la Music&Lights S.r.l. si riserva la facoltà di modicare, in

qualunque momento e senza preavviso, le speciche menzionate nel presente manuale di istruzioni.

Tutte le revisioni e gli aggiornamenti sono disponibili nella sezione 'Manuali' sul sito www.musiclights.it

REV. 02-10/20

La pagina sta caricando ...

ProLights SMARTOWERPACK Manuale utente

Questo manuale è adatto anche per

ProLights SMARTOWERPACK Manuale utente

in altre lingue

Documenti correlati

Altri documenti