ProLights SMARTMODULA Manuale utente

EN - IT

USER MANUAL

MANUALE UTENTE

NEW FORM OF DECOR AND MODULAR

BATTERY LIGHT

SMARTMODULA

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the

characteristics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

REV.03-10/18

Packing content

• SMARTMODULA

• Power cable

• User manual

TABLE OF

CONTENTS

Safety

General instructions

Warnings and installation precautions

1 Introduction

1. 1 Description

1. 2 Technical specications

1. 3 Technical specications MODULASPOTFC-DY

1. 4 Technical specications MODULAWASHFC-D

1. 5 Battery features

1. 6 Operating elements and connections

2 Installation

2. 1 Mounting

3 Functions and settings

3. 1 Operation

3. 2 Basic

3. 3 Menu structure

3. 4 DMX Mode

3. 5 DMX conguration

3. 6 DMX Addressing

3. 7 Pixel mode

3.8 Wireless

3. 9 Backlight

3. 10Flip display

3. 11 Dimmer

3. 12 Calibration

3. 13 Reload Default

3. 14 Time info

3. 15 Software version

3. 16 Static mode

3. 17 Controller IR

3. 18 DMX control

4 Maintenance

4. 1 Maintenance and cleaning the unit

4. 2 Fuse replacement

4. 3 Troubleshooting

2

3

6

7

8

9

11

12

13

14

15

16

18

SMARTMODULA

2

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

SAFETY

General instruction

• The products referred to in this manual conform to the European Community Directives and are there-

fore marked with .

• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.

Never make any modications on the unit not described in this instruction manual, otherwise you will

risk an electric shock.

• Connection must be made to a power supply system tted with ecient earthing (Class I appliance ac-

cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units

from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• The connection to the main network of electric distribution must be carried out by a qualied electrical

installer. Check that the main frequency and voltage correspond to those for which the unit is designed

as given on the electrical data label.

• This unit is not for home use, only professional applications.

• Never use the xture under the following conditions:

- in places subject to vibrations or bumps;

- in places with a temperature of over 45 °C.

• Make certain that no inammable liquids, water or metal objects enter the xture.

• Do not dismantle or modify the xture.

• All work must always be carried out by qualied technical personnel. Contact the nearest sales point for

an inspection or contact the manufacturer directly.

• If the unit is to be put out of operation denitively, take it to a local recycling

plant for a disposal which is not harmful to the environment.

Warnings and installation precautions

• If this device will be operated in any way dierent to the one described in this manual, it may suer

damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like

short circuit, burns, electric shock, etc.

• Before starting any maintenance work or cleaning the projector, cut o power from the main supply.

• Always additionally secure the projector with the safety rope. When carrying out any work, always com-

ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country

in which the xture’s being used.

• Install the xture in a well ventilated place.

• Keep any inammable material at a safe distance from the xture.

• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent

that their eectiveness is impaired.

• The lamp (LED) shall be changed if it has become damaged or thermally deformed.

• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ashing light, may

trigger epileptic seizures in photosensitive persons or persons with epilepsy.

• Do not touch the product’s housing when operating because it may be very hot.

3

SMARTMODULA

- 1 - INTRODUCTION

1.1 DESCRIPTION

SMARTMODULA is a cable-free battery xture which establishes a new form of decor lighting for events,

banquets and gardens. Its modular and customizable assembly allow to use the luminaire standing from

the oor or hanged as a pinspot four-bar, and packed in a comfortable carry-on sizes. Thelight emitters

are adjustable and can slide on the track for a perfect focusing, and as well be replaced from Spot to Wash

or mixed congurations and available in FC or White color mixing.

SMARTMODULA (Core components to be completed with accessories) includes:

- Floor metal base plate

- Base with supporting bar

- Extension bar with adjustable wight

- Heading bar with light track and electronics (containing 1 battery)

OPTIONALaccessories to complete the Core element:

- MODULASPOT: 2pcs Spot LED Dot with 1 LED source 12° beam, available in FC or WHite color mixing

(Max 6pcs on each SMARTMODULA).

- MODULAWASH: 1pc wash LED strip with 12x3W LED, 60° beam, available in FC or WHite color mixing

(Max 1pcs on each SMartModula + 2 Spot).

- MODULABBAT: 1pc base extra-battery to be installed inside the Base to extend battery operation (Max

2pcs MODULABBAT in each baseplate).

Features:

MODULA design allows oor standing with exible swivel joints and tiltable stand, or hanging with quick-

lock omega brackets

Accessory xtures available in RGBW/FC and White Color mixing, as well as with Spot or Wash Optics, each

emitter is pixel mapped, can slides and be focused individually (not included)

The base houses room for extra battery (optional) and the stand can be adjusted in height.

1.2 TECHNICAL SPECIFICATIONS

LIGHT SOURCE

• Source: W Light source is supplied as accessory as SPOT or WASH, FC or White

• CT: Optional - FC or WH SPOT 5600 K or WH WASK 6400 K

• Source Life Expectancy: >30.000 h

• Other: Light source is supplied as accessory as SPOT or WASH, FC or White

OPTICS

• Beam Angle: SPOT (Opt) 15°; WASH (Opt) 60 °

COLOR SYSTEM

• Color Mixing: Interchangeable light source: SPOTs or WASH with FullColor or White LED source

DYNAMIC EFFECTS

• Static Color Mode: Selection of static color

• Manual Color Mode: Manual adjustment of color

• Auto Mode: Built-in programs with execution speed adjustment

SMARTMODULA

4

BODY

• Hardware On-board: See the Introduction description

• Pan Angle: 360 ° Metal joint for 360° rotation of header bar

• Tilt Angle:120 ° Manual

• Body: Sturdy stretching aluminium body conceived for long-time durability

• Body Color: Matte black

CONTROL

• Protocols: WDMX

• Pixel Control: Pixel2Pixel control

• W-DMX: Included, Wireless Solution receiver

• Display: Black OLED high resolution display

• IR: Infra-Red sensor controlled by remote

ELECTRONICS

• Dimmer: Linear 0~100% electronic dimmer

• Strobe/Shutter:1~25 Hz, electronic

• Operating Temperature: -10° ~ +40°

• Flicker: Flicker free operation

ELECTRICAL

• Power Supply: 100-240V – 50/60Hz

BATTERY

• Battery:(Head) 1x14.8 V - (Base - optional) 1x14.8 V Lithium

• Autonomy in color change mode, up to:refer to user manual for max h

• Autonomy in single color mode, up to:refer to user manual for max h

• Autonomy in full-on, up to:refer to user manual for max h

• Recharge Connection: Power cable

• Recharge Time:Head battery 5,5 h/max Base battery 11 h/max

• Battery Status: LED battery status indicator

• Other:Check User manual for further information about battery autonomy for all possible compositions

PHYSICAL

• Cooling: Natural cooling of the peculiar chassis and to absence of fans

• Suspension And Fixing: Hanging bracket suitable for safe hanging and positioning

• Power Connection: PowerCON TRUE1 in

• IP:20

• Dimensions (WxHxD): 735x(1456~1916)x958 mm

• Weight:w/o baseplate 23,5Kg, with baseplate 38,5 kg

5

SMARTMODULA

Technical drawing Fig.1

1916 [75.43 in]

1456 [57.32 in]

689 [27.14 in]

735 [28.93 in]

SMARTMODULA

6

80 [3.14 in]

110 [4.33 in]

80 [3.14 in]

1.4 TECHNICAL SPECIFICATIONS MODULAWASHFC-DY

LIGHT SOURCE

• Source:(FC) 12x6 W - (DY) 12x3 W LEDs

• CT:(DY) 6400 K

• CRI:(DY) 81 Ra

• Luminous Flux:(DY) 1213 lm - (FC) 2778 lm

• Lux:(DY) 3800 lux - (FC) 8340 lux @1m Full

• Lux:(DY) 468 lux - (FC) 1110 lux @3m Full

• Source Life Expectancy: >50.000 h

• Other:Max 1pc Modulawash per Smartmodula (+2pcs SPOT)

OPTICS

• Beam Angle:60 °

• Field Angle:65 °

ELECTRICAL

• Power Consumption:(Single FC) 27 W - (Single DY) 15W

PHYSICAL

• Dimensions (WxHxD):500x55x55 mm

• Weight:0,8 kg

1.3 TECHNICAL SPECIFICATIONS MODULASPOTFC-DY

LIGHT SOURCE

• Source:(FC) 1x10 W - (DY) 1x3 W LEDs

• CT:(DY) 5600 K

• CRI:(DY) 70,9 - (FC) 37.6 Ra

• Luminous Flux:(1xDY) 194 lm - (1xFC) 254 lm

• Lux:(1xDY) 5320 lx - (1xFC) 5150 lux @1m Full

• Lux:(1xDY) 477 lx - (1xFC) 453 lux @3m Full

• Source Life Expectancy: >50.000 h

• Other:Max 6pc Modulaspot per Smartmodula

OPTICS

• Beam Angle:15 °

• Field Angle:23 °

ELECTRICAL

• Power Consumption:(Single FC) 5.5 W - (Full FC) 33 W - (Single DY) 1.5 W - (Full DY) 9 W

PHYSICAL

• Dimensions (WxHxD):80x80x110 mm

• Weight:0,25 kg

Technical drawing Fig.2

7

SMARTMODULA

55 [2.16 in]

500 [19.68 in]

Technical drawing Fig.3

1.5 BATTERY FEATURES

QTY

(PCS)

FULL

COLOR’S

POWER

(W)

LIGHTING HOURS (h) SINGLE

COLOR’S

POWER

(W)

LIGHTING HOURS (h) COLOR

CHANGING’S

POWER (W)

LIGHTING HOURS (h)

HEAD

BAR’S

BATTERY

HEAD BAR’S

BATTERY+BACK

UP BATTERY

HEAD

BAR’S

BATTERY

HEAD BAR’S

BATTERY+BACK

UP BATTERY

HEAD

BAR’S

BATTERY

HEAD BAR’S

BATTERY+BACK

UP BATTERY

MODULASPOTFC 1 5,8 25 75 1,9 77 231 2,85 51 154

2 11,4 13 39 3,8 38 115 5,7 25 76

3 17,1 9 26 5,7 25 76 8,55 17 51

4 22,8 6 19 7,6 19 58 11,4 13 39

5 27,7 5 16 9,5 15 46 14,25 10 31

6 34,1 4 13 11,4 13 38 17,1 8 25

MODULAWASHFC 1 52 2 8 21,3 6 21 31,95 4 13

MODULASPOTDY 1 1,5 97 292

2 3 49 146

3 4,5 32 97

4 6 24 73

5 7,5 19 57

6 9 16 49

MODULAWASHDY 1 15 9 27

MODULAWASH

MODULASPOT

1

2

54 2 8

SMARTMODULA

8

1.6 OPERATING ELEMENTS AND CONNECTIONS

Fig.4

1. FLOOR METAL BASE PLATE

2. THREADED HOLES M8

3. BASE WITH SUPPORTING BAR

4. POWER IN (PowerCON IN):

for connection to a socket

(100-240V~/50-60Hz) via the

supplied mains cable.

5. FUSE

6. SLOT to house the MODULABBAT

extra battery

7. EXTENSION BAR WITH ADJUSTABLE

HEIGHT

8. BLOCKING SYSTEM

9. FLEX SWIVEL JOINT

10. HEADING BAR

11. MODULAWASH

12. MODULASPOT

13. POWER IN (PowerCON IN): per il

collegamento ad una presa di rete

(100-240V~/50-60Hz) tramite il cavo

rete in dotazione.

14. IMPUT for cable DC IN 24V.

15. HOLE for hook.

16. CONTROL PANEL with OLED display

and 4 button used to access the

control panel functions and manage

them.

17. TRACK to working the MODULASPOT/

WASH.

18. ON/OFF SWITCH to turn the

SMARTMODULA.

1

3

5

4

6

7

2

8

9

10

12

11

16

514

13

15

17

18

9

SMARTMODULA

3

1

7

8

9

1

2

3 4

- 2 - INSTALLATION

2.1 MOUNTING

Fig.5 - Examples conguration

SMARTMODULA

10

165°

958 [37.71 in]

165°

958 [37.71 in]

165°

958 [37.71 in]

165°

958 [37.71 in]

1916 [75.43 in]

735 [28.94 in]

2866 [112.84 in]

1456 [57.33 in]

735 [28.94 in]

2406 [94.74 in]

1916 [75.43 in]

735 [28.94 in]

2868 [112.91 in]

1456 [57.33 in]

735 [28.94 in]

2408 [94.80 in]

Fig.6

11

SMARTMODULA

Fig.7 - Functions of the buttons

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

Connect the supplied main cable to a socket (100-240 VAC-50/60 Hz). Then the unit is ready for operation

and can be operated via a DMX controller or it independently performs its show program in succession.

To switch o, disconnect the mains plug from the socket. For a more convenient operation it is recom-

mended to connect the unit to a socket which can be switched on and o via a light switch.

3.2 BASIC

Access control panel functions using the four panel buttons located directly underneath the OLED Display

(g.4).

MENU/ESC UP DOWN ENTER

Used to access the menu or

to return a previous menu

option

Navigates downwards through

the menu list and increases

the numeric value when in a

function

Navigates upwards through

the menu list and decreases

the numeric value when in

a function

Used to select and store the

current menu or conrm the

current function value or

option within a menu

SMARTMODULA

12

3.3 MENU STRUCTURE

MENU

1 CONNECT

ð

DMX Address

ð

Value (001-485)

DMX Mode

ð

1CH

5CH

8CH

PIXCH

Pixel

ð

Order

ð

(001-006)

Wireless

ð

Reset Connect

ð

NO-Yes

2

SETUP

ð

Screen

ð

Back Light

Flip Display

ð

2 ~ 99m

NO-Yes

Adjust

ð

Dimmer

3

ADVANCED

ð

Calibration

ð

Password

Red

Green

Blue

White

ð

Value (001-255)

Reload Default

ð

Basic Default

Password

Private Default

All Default

ð

OFF-On

4

INFORMATION

ð

Time Info

Software version

ð

Current

V1.0

5

STATIC

ð

Presets

ð

Red

Deep Orange

Light Orange

Yellow

Green

Sea Green

Acquamarine

Cyan

Blue

Violet

Purple

Magenta

Full RGB

White

Gradual

13

SMARTMODULA

3.4 DMX ADDRESS

To set the DMX address, press the MENU button until shows CONNECT on the display, then select DMX

ADDRESS and press the ENTER button.

• Press the UP/DOWN button to select the desired value (001-485); Press and hold the UP/DOWN button

to scroll quickly.

• Press ENTER button to store.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.5 DMX CONFIGURATION

SMARTMODULA is equipped with dierent DMX conguration.

• Press the button MENU so many times until shows CONNECT, then select DMX MODE, and press the button

ENTER to conrm.

• Select the desired DMX conguration (1CH - 5CH - 8CH, PIXCH) through the buttons UP/DOWN.

The tables on page 16 and 17 indicate the operating mode and DMX value.

3.6 DMX ADDRESSING

To able to operate the SMARTODULA with a light controller, adjust the DMX start address for the rst a

DMX channel. If e. g. address 33 on the controller is provided for controlling the function of the rst DMX

channel, adjust the start address 33 on the SMARTMODULA.

The other functions of the light eect panel are then automatically assigned to the following addresses.

An example with the start address 33 is shown below:

Number of

DMX channels

Start address

(example)

DMX Address

occupied

Next possible start

address for unit No. 1

Next possible start

address for unit No. 2

Next possible start

address for unit No. 3

1 33 33 34 35 36

5 33 33-37 38 43 48

8 33 33-40 41 49 57

3.7 PIXEL

• Set an order number to the Dot&Strip. If you want to set an order number with one Dot/Strip, you

need to take o other Dots/Strips at rst. Or you want to set a same order number with two/three/

more Dots&Strips, you can insert all of them into the bar. Then you should go into the order number

setting menu(Connect->Pixel->Order) , use “UP/DOWN” for selecting the number and press “ENTER” for

conrmation. Please be aware of that the biggest number is 6.

• Press the UP/ DOWN button to scroll through the menu, select CONNECT then press the ENTER button to

access the next menu).

• Press the UP/DOWN button to select PIXEL, and press the ENTER button to proceed.

• Press the MENU button repeatedly to exit the menu and to save the changes made.

• NOTE: Pixel control can not work while you are using the IR remote-controller.

• NOTE: When the slider bar is short-circuit, the battery will power o for protection. And this protection

will be relieved if charge it for a few minute.

3.8 WIRELESS

To enable wireless control mode, proceed as follows:

• Press the UP/DOWN button to scroll the menu, select CONNECT, then press the ENTER button to enter

SMARTMODULA

14

• the next menù.

• Press theUP/DOWN button to select WIRELESS then press the ENTER button to store.

• Select RESET CONNECT to reset the unit and press the ENTER button to store.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.9 BACKLIGHT

Backlight display Auto O. This feature allows you to automatically turn o the backlight after a specied

time that you can set using the arrow buttons. Set a value between those indicated to turn o the display

once the chosen time has elapsed, after exiting the menu.

• Press the UP/DOWN button to scroll the menu, select SET UP, then press the ENTER button to enter the

next menù.

• Press theUP/DOWN button to select SCREEN then press the ENTER button to store.

• Select the proposed option with the UP / DOWN button and press the ENTER button to conrm.

• Press the ENTER button to conrm the choice.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.10 FLIP DISPLAY

Display orientation. This feature allows you to rotate the display by 180 ° to get a better view of the display

when the unit is hanging upside down. Select ON to activate the function or OFF to deactivate it.

• Press the UP/DOWN button to scroll the menu, select SET UP, then press the ENTER button to enter the

next menù.

• Press theUP/DOWN button to select SCREEN then press the ENTER button to store.

• Select the proposed option with the UP / DOWN button and press the ENTER button to conrm.

• Press the ENTER button to conrm the choice.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.11 DIMMER

To enter the dimmer mode and choose and simulate dierent dimming curves.

• Press the UP/DOWN button to scroll the menu, select SET UP, then press the ENTER button to enter the

next menù.

• Press the UP/DOWN button to select ADJUST and press the ENTER button to conrm.

• Select the proposed option with the UP / DOWN button and press the ENTER button to conrm.

• Press the ENTER button to conrm the choice.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.12 CALIBRATION

Per lo SMARTMODULA is possible to calibrate the intensity of the color:

• Press the UP/DOWN button to scroll the menu, select ADVANCED, then press the ENTER button to enter

the next menù.

• Press the UP/DOWN button to select CALIBRATIONand press the ENTER button to conrm.

• Select the proposed option with the UP / DOWN button and press the ENTER button to conrm.

• Press the ENTER button to conrm the choice.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

•

3.13 RELOAD DEFAULT

Select this function to restore the drive to default settings:

15

SMARTMODULA

• Press the UP/DOWN button to scroll the menu, select ADVANCED,then press the ENTER button to enter

the next menù.

• Press the UP/DOWN button to select RELOAD DEFAULT and press the ENTER button to conrm.

• Select the proposed option with the UP / DOWN button and press the ENTER button to conrm:

- Basic Default:

- Private Default:

- All Default:

• Press the ENTER button to conrm the choice.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.14 TIME INFO

Select this function to display the operating time of the projector on the display.

• Press the UP/DOWN button to scroll the menu, select INFORMATION,then press the ENTER button to enter

the next menù.

• Press the UP/DOWN button to select TIME INFO and press the ENTER button to conrm and display the

desired information.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.15 SOFTWARE VERSION

Select this function to display the version of the installed software on the display.

• Press the UP/DOWN button to scroll the menu, select INFORMATION,then press the ENTER button to enter

the next menù.

• Press the UP/DOWN button to select SOFTWARE VERSION and press the ENTER button to conrm and di-

splay the desired information.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.16 STATIC MODE

The unit has preset pre-programmed colors that can be set through the

following procedure:

• Press the UP/DOWN button to scroll the menu, select STATIC, then press

the ENTER button to enter the next menù.

• Select PRESETS throught the UP/DOWN button, then press the ENTER

button to conrm.

• Set the color (Red, Deep Orange, Light Orange, Yellow, Green, Sea Green,

Aquamarine, Cyan, Blue, Violet, Purple, Magenta, Full RGB, White, Gradual) throu-

ght the UP/DOWN button, then press the ENTER button to conrm.

• Press the MENU button to go back or to meet the waiting time to exit

the setup menu.

Fig.8

3.17 CONTROLLER IR

Make sure to point the controller directly at the IR receiver near the switch

to turn on/o the SMARTMODULA.

Use the keys as below to access the functions.

FADE

SOUND

SENSIT.

AUTO

MACRO

POWER

STROBESPEEDDIMMERMANUAL

AMBER

UV

RED

YELLOW

CYAN

MAGENTA

STATIC

DEEP

ORANGE

LIGHT

ORANGE

SEA

GREEN

AQUA

MARINE

WARM

WHITE

COLD

WHITE

GREEN

BLUE VIOLET PURPLE

WHITE

SMARTMODULA

16

3.18 DMX CONTROL

1 CHANNEL

MODE

FUNCTION DMX

Value

1 Ch

1

WHITE

0~100% 000 - 255

5 CHANNELS

MODE

FUNCTION DMX

Value

5 Ch

1

DIMMER

0~100% 000 - 255

2

RED

0~100% 000 - 255

3

GREEN

0~100% 000 - 255

4

BLUE

0~100% 000 - 255

5

WHITE

0~100% 000 - 255

8 CHANNELS

MODE

FUNCTION DMX

Value

8 Ch

1

DIMMER

0~100% 000 - 255

2

RED

0~100% 000 - 255

3

GREEN

0~100% 000 - 255

4

BLUE

0~100% 000 - 255

5

WHITE

0~100% 000 - 255

6

VIRTUAL COLOR

No Function

Red

000 - 015

016 - 025

PIXCH

MODE

FUNCTION DMX

Value

PIXCH

1

DIMMER

0~100% 000 - 255

2

VIRTUAL COLOR

No Function

Red

Deep Orange

Light Orange

Yellow

Green

Sea Green

Aquamarine

Cyan

Blue

Violet

Purple

Magenta

Full RGB

White

Gradual

000 - 015

016 - 025

026 - 035

036 - 045

046 - 055

056 - 065

071 - 090

066 - 075

076 - 085

086 - 095

096 - 105

106 - 115

116 - 125

126 - 135

136 - 145

146 - 155

156 - 255

3

SHUTTER FUNCTION

Normal Shutter Function

Strobe eect slow to fast

000 - 031

032 - 255

4

DIMMER FADE

0~100%

000 - 255

6

Deep Orange

Light Orange

Yellow

Green

Sea Green

Aquamarine

Cyan

Blue

Violet

Purple

Magenta

Full RGB

White

Gradual

026 - 035

036 - 045

046 - 055

056 - 065

071 - 090

066 - 075

076 - 085

086 - 095

096 - 105

106 - 115

116 - 125

126 - 135

136 - 145

146 - 155

156 - 255

7

SHUTTER FUNCTION

Normal Shutter Function

Strobe eect slow to fast

000 - 031

032 - 255

8

DIMMER FADE

0~100%

000 - 255

17

SMARTMODULA

PIXCH

MODE

FUNCTION DMX

Value

PIXCH

5

RED 1

0~100% 000 - 255

6

GREEN 1

0~100% 000 - 255

7

BLUE 1

0~100% 000 - 255

8

WHITE 1

0~100% 000 - 255

25

RED 6

0~100% 000 - 255

26

GREEN 6

0~100% 000 - 255

27

BLUE 6

0~100% 000 - 255

28

WHITE 6

0~100% 000 - 255

SMARTMODULA

18

- 4 - MAINTENANCE

4.1 MAINTENANCE AND CLEANING THE UNIT

• Make sure the area below the installation place is free from unwanted persons during setup.

• Switch o the unit, unplug the main cable and wait until the unit has cooled down.

• All screws used for installing the device and any of its parts should be tightly fastened and should not

be corroded.

• Housings, xations and installation spots (ceiling, trusses, suspensions) should be totally free from any

deformation.

• The main cables must be in impeccable condition and should be replaced immediately even when a

small problem is detected.

• It is recommended to clean the front at regular intervals, from impurities caused by dust, smoke, or

other particles to ensure that the light is radiated at maximum brightness. For cleaning, disconnect the

main plug from the socket. Use a soft, clean cloth moistened with a mild detergent. Then carefully wipe

the part dry. For cleaning other housing parts use only a soft, clean cloth. Never use a liquid, it might

penetrate the unit and cause damage to it.

4.2 FUSE REPLACEMENT

1. Disconnect this product from the power outlet.

2. Remove the safety cap by a screwdriver.

3. Replace the blown fuse with a fuse of the exact same type and rating.

4. Install the safety cap, and reconnect power.

4.3 TROUBLESHOOTING

Problems Possible causes Checks and remedies

Fixture does not light up

• No mains supply

• Dimmer fader set to 0

• All color faders set to 0

• Faulty LED

• Faulty LED board

• Check the power supply voltage

• Increase the value of the dimmer channels

• Increase the value of the color channels

• Replace the LED board

General low light intensity

• Dirty lens assembly

• Misaligned lens assembly

• Clean the xture regularly

• Install lens assembly properly

Fixture does not power up

• No power

• Loose or damaged power cord

• Faulty internal power supply

• Check for power on power outlet

• Check power cord

• Replace internal power supply

Fixture does not respond to DMX

• Wrong DMX addressing

• Damaged DMX cables

• Bouncing signals

• Check control panel and unit addressing

• Check DMX cables

• Install terminator as suggested

Contact an authorized service center in case of technical problems or not reported in the table can not be

resolved by the procedure given in the table.

La pagina sta caricando ...

ProLights SMARTMODULA Manuale utente

ProLights SMARTMODULA Manuale utente

in altre lingue

Documenti correlati

Altri documenti