Panasonic SVAV100 Manuale del proprietario

SD Video Camera

Operating Instructions

Model No. SV-AV100

Before use, please read these instructions completely.

VQT0F57

For USA assistance. please call:1-800-211-PANA(7262) or send e-mail to:consumerproducts@panasonic.com

For Canadian assistance. please call:1-800-561-5505 or visit us at www.panasonic.ca

PP

AV100PP.book 1 ページ２００３年８月２２日　金曜日　午後４時３０分

O

Before opening the CD-ROM package, please read the following.

båÇ=rëÉê=iáÅÉåëÉ=^ÖêÉÉãÉåí

You (“Licensee”) are granted a license for the Software defined in this End User License Agreement

(“Agreement”) on condition that you agree to the terms and conditions of this Agreement. If Licensee

does not agree to the terms and conditions of this Agreement, promptly return the Software to

Matsushita Electric Industrial Co., Ltd. (“Matsushita”), its distributors or dealers from which you

made the purchase.

Article 1 License

Licensee is granted the right to use the Software, including the information recorded or described on

the CD-ROM, instruction manuals, and any other media provided to Licensee (collectively

“Software”), but all applicable rights to patents, copyrights, trademarks and trade secrets in the

Software are not transferred to Licensee.

Article 2 Use by a Third Party

Licensee may not use, copy, modify, transfer or allow any third party, whether free of charge or not,

to use, copy or modify the Software, except as expressly provided for in this Agreement.

Article 3 Restrictions on Copying the Software

Licensee may make a single copy of the Software in whole or in part solely for back-up purpose.

Article 4 Computer

Licensee may use the Software only on one computer, and may not use it on more than one

computer.

Article 5 Reverse Engineering, Decompiling or Disassembly

Licensee may not reverse engineer, decompile, or disassemble the Software, except to the extent

either of them is permitted under law or regulation of the country where Licensee resides.

Matsushita, or its distributors will not be responsible for any defects in the Software or damage to

Licensee caused by Licensee’s reverse engineering, decompiling, or disassembly of the Software.

Article 6 Indemnification

The Software is provided “AS-IS” without warranty of any kind, either expressed or implied,

including, but not limited to, warranties of non-infringement, merchantability and/or fitness for a

particular purpose. Further, Matsushita does not warrant that the operation of the Software will be

uninterrupted or error free. Matsushita or any of its distributors will not be liable for any damage

suffered by Licensee arising from or in connection with Licensee’s use of the Software.

Article 7 Export Control

Licensee agrees not to export or re-export to any country the Software in any form without the

appropriate export licenses under regulations of the country where Licensee resides, if necessary.

Article 8 Termination of License

The right granted to Licensee hereunder will be automatically terminated if Licensee contravenes

any of the terms and conditions of this Agreement. Upon termination hereof, Licensee must destroy

the Software and related documentation together with all the copies thereof at Licensee’s own

expense.

AV100PP.book 2 ページ２００３年８月２２日　金曜日　午後４時３０分

P

`çåíÉåíë

End User License Agreement.......... 2

Information for Your Safety............... 4

Introduction ...................................... 7

mêÉé~ê~íáçå

Standard Accessories...................... 8

Optional Accessory.......................... 9

Controls and Components ............. 10

Power Supply................................. 12

Fitting the Camera on

the AV Cradle................................ 13

Inserting a Memory Card............... 14

Using the LCD Monitor .................. 15

Turning the Power On/Selecting

Operation Modes .......................... 17

Using the Menu Screen ................. 18

List of Menus ................................. 19

Setting Date and Time ................... 22

Adjusting Brightness and

Color Level on the LCD Monitor.... 24

_~ëáÅ=cìåÅíáçåë

Before Recording operation........... 25

Clean Up Function......................... 26

Recording Motion Images

(MPEG2)....................................... 27

Recording Motion Images

(MPEG4)....................................... 28

Playing Back Motion Images

(MPEG2)....................................... 29

Playing Back Motion Images

(MPEG4)....................................... 30

Adjusting the Volume ..................... 31

Recording Still Pictures.................. 32

Playing back Still Pictures.............. 33

Play Back All of the Still Pictures

One by One (Slide Show)............. 34

^Çî~åÅÉÇ=cìåÅíáçåë

Zoom In/Out Functions...................35

Backlight Compensation

Function ........................................ 35

Adjusting White Balance ................36

Manual Exposure Adjustment ........37

Manual Focus Adjustment..............37

Recording in Special Situations

(Program AE) ................................ 38

Digital Electronic Image

Stabilizer Function.........................39

Wind Noise Reduction Function.....39

Using the Play Menu Functions......40

Playing Back on

an external device.........................54

Recording pictures supplied from

an external device.........................55

Storing on the PC...........................56

Using the DVD Video Recorder

with a Hard Disk............................57

lå=~=mÉêëçå~ä=`çãéìíÉê

About the supplied software...........58

USB Driver .....................................59

MediaStage for AV100 ................... 60

Installing MediaStage

& USB Driver.................................61

Installing USB Driver ......................62

Connecting with the PC..................63

Starting the Software .....................64

Disconnecting

the USB Cable safely ....................64

If you no longer need software

(Uninstall)......................................64

Constructing a Folder when the

Memory Card is used with a PC ...65

AV100PP.book 3 ページ２００３年８月２２日　金曜日　午後４時３０分

Q

líÜÉêë

Charge the built-in battery for

maintaining the date information...66

Using the Optional Earphones .......66

Using Accessories..........................67

After Use ........................................69

Indications (Recording Mode) ........70

Indications (Playback Mode) ..........72

Notes & Precautions.......................75

Notes and Hints..............................78

Before Requesting Service.............86

Specifications.................................89

Limited Warranty

(For U.S.A. Only)...........................91

Customer Services Directory

(For U.S.A. Only)...........................93

Index...............................................94

pé~åáëÜ=nìáÅâ=rëÉ=dìáÇÉL

dì∞~=Éëé~¥çä~=é~ê~=Éä=ìëç=

ê•éáÇç

Alimentación eléctrica ....................95

Cómo encajar la cámara

en el soporte .................................96

Inserción de la Tarjeta

de memoria ...................................97

Encendido/Selección de

los modos de funcionamiento .......98

Grabación de imágenes

dinámicas/imágenes estáticas ......99

Reproducción de imágenes

dinámicas/imágenes estáticas ......99

Dear Customer,

We would like to take this opportunity to

thank you for purchasing this Panasonic SD

Video Camera. Please read these

Operating Instructions carefully and keep

them handy for future reference.

fåÑçêã~íáçå=Ñçê=vçìê=

p~ÑÉíó

IMPORTANT

Please respect all copyrights.

Whatever you have recorded and created

can be used for your personal

entertainment only. Under copyright

laws, other materials cannot be used

without obtaining permission from the

holders of the copyrights.

WARNING

TO REDUCE THE RISK OF FIRE OR

SHOCK HAZARD AND ANNOYING

INTERFERENCE, USE ONLY THE

RECOMMENDED ACCESSORIES AND

DO NOT EXPOSE THIS EQUIPMENT TO

RAIN OR MOISTURE. DO NOT REMOVE

THE COVER (OR BACK); THERE ARE

NOT USER SERVICEABLE PARTS

INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

Notice:

This product has parts that contain a small

amount of mercury. It also contains lead in

some components. Disposal of these

materials may be regulated in your

community due to environmental

considerations. For disposal or recycling

information please contact your local

authorities, or the Electronics Industries

Alliance: <http://www.eiae.org.>

AV100PP.book 4 ページ２００３年８月２２日　金曜日　午後４時３０分

R

≥Injury or material damage resulting

from any kind of use that is not in

accordance with the operating

Instructions are the sole responsibility

of the user.

≥After long operation, this device can get

warm. This is not a malfunction. The

cautions label is stuck on the surface of

the SD Video Camera.

≥The manufacturer shall in no event be

liable for the loss of recordings due to

malfunction or defect of this SD Video

Camera, its accessories or Memory Card.

≥Please note that the actual controls and

components, menu items, etc. of your SD

Video Camera may look somewhat

different from those shown in the

illustrations in these Operating

Instructions.

≥

:

SD logo is a trademark.

≥The SD Video Camera uses copyright-

protected technologies and is protected by

the patented technologies and intellectual

properties of Japan and the U.S. To use

these copyright-protected technologies,

authorization of the Macrovision Company

is required. It is prohibited to disassemble

or modify the SD Video Camera.

≥(l 00) indicates the page to be referred

to.

≥Note that the SD Video Camera may not

play back data recorded or created on

another product and another product may

not play back data recorded on the SD

Video Camera.

≥The nameplate of the SD Video Camera is

fixed on the bottom of the battery

compartment.

Extremely high precision technology is

employed to produce the LCD Monitor

screen featuring a total of approximately

123,000 pixels. The result is more than

99.99% effective pixels with a mere

0.01% of the pixels inactive or always lit.

However, this is not a malfunction and

does not affect the recorded picture.

U.S. Patent Nos. 4,631,603, 4,577,216, 4,819,098, and 4,907,093.

This product incorporates copyright protection technology that is protected by U.S.

patents and other intellectual property rights. Use of this copyright protection technology

must be authorized by Macrovision, and is intended for home and other limited consumer

uses only unless otherwise authorized by Macrovision. Reverse engineering or

disassembly is prohibited.

A lithium ion/polymer battery that is recyclable powers the product you

have purchased. Please call 1-800-8-BATTERY for information on how to

recycle this battery.

RBRC

Li-ion

TM

AV100PP.book 5 ページ２００３年８月２２日　金曜日　午後４時３０分

S

FCC Note: (U.S. only)

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

≥Reorient or relocate the receiving antenna.

≥Increase the separation between the equipment and receiver.

≥Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

≥Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: To assure continued compliance, follow the attached

installation instructions and use only shielded interface

cables with ferrite core when connecting to a computer or

peripheral devices.

Any changes or modifications not expressly approved by the

party responsible for compliance could void the user’s

authority to operate this equipment.

Trade Name: Panasonic

Model No.: SV-AV100

Responsible party: Matsushita Electric Corporation of America One Panasonic

Way, Secaucus, NJ 07094

Support Contact: Panasonic Consumer Electronics Company

1-800-211-PANA(7262)

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may

cause undesired operation.

This Class B digital apparatus complies with Canadian ICES-003.

SV-AV100

AV100PP.book 6 ページ２００３年８月２２日　金曜日　午後４時３０分

T

fåíêçÇìÅíáçå

This SD Video Camera can record MPEG2/

MPEG4 motion images and still pictures.

Additionally, using the viewer software,

MediaStage for AV100 (supplied

accessory), the MPEG2/MPEG4 motion

images data can be edited on the personal

computer.

ª Charging the Battery

Be sure to charge the supplied battery

before use.

≥Refer to Page 12 for the procedures to

attach and charge the battery.

ª Clock setting

Prior to use the clock in this SD Video

Camera needs to be set. Please turn to

page 22 for additional information.

ª About Using an SD Memory

Card

This product is capable of recording in the

MPEG2 format, producing video quality that

is comparable to digital camcorders. To

achieve this level of performance, large

amounts of data must be written to the SD

card in real time.

The read and write speed of the SD card

may differ from manufacturer to

manufacturer. In MPEG2 motion image

recording, SD card with the high-speed

transmission rate of 10 MB/s is needed. The

use of SD cards other than the above may

result in the following error message: [This

card cannot record in the MPEG2 mode.]

For additional information on other brand

cards that are known to be compatible,

please visit this web site:

For USA

<http://www.panasonic.com/d-snap>

For Canada

<http://www.panasonic.ca/english/

accessories/storagemedia/>

AV100PP.book 7 ページ２００３年８月２２日　金曜日　午後４時３０分

U

mêÉé~ê~íáçå

pí~åÇ~êÇ=^ÅÅÉëëçêáÉë

1 AC Adaptor (VSK0617) (l 12)

≥Supplies power to the SD Video

Camera.

2 Battery Pack (CGA-S302A) (l 12)

≥Supplies power to the SD Video

Camera.

3 AC Cord (K2CA2EA00002) (l 12)

4 USB Cable (K2KZ4CB00002) (l 63)

5 Remote Controller (N2QACC000005)

and Button-Type-Battery (CR2025)

(l 68)

6 AV Cable (K2KC4CB00009) (l 54, 55)

7 Hand Strap (VFC4012) (l 68)

8 AV Cradle (VSK0653) (l 13)

9 Lens Cap (VGQ7448) and

Lens Cap Cord (VFC4035) (l 68)

AV100PP.book 8 ページ２００３年８月２２日　金曜日　午後４時３０分

V

10 CD-ROM (l 58)

MediaStage for AV100,

USB Driver, DirectX,

Adobe Acrobat Reader

≥For using the MediaStage, refer to the

PDF manual. This manual describes

installation only.

11 Card Case/Movie Stand (VFC4032)

(l 69) and SD Memory Card

(512 MB) (RP-SDH512VE0) (l 14)

12 Wearable Carry Case (VFC4020)

≥Put the SD Video Camera in the

Wearable Carry Case supplied after

use or when carrying it.

léíáçå~ä=^ÅÅÉëëçêó

1 Battery Pack (CGA-S302A/1B) (l 12)

≥Supplies power to the SD Video

Camera.

512

AV100PP.book 9 ページ２００３年８月２２日　金曜日　午後４時３０分

NM

`çåíêçäë=~åÇ=`çãéçåÉåíë

1 Lens (l 76)

2 Recording Lamp (l 19)

3 Remote Control Sensor (l 68)

4 AV Input/Output Terminal [AV IN/OUT]

(l 54, 55)

Earphone Terminal [ ] (l 66)

5 USB Terminal (l 63)

6 DC Input Socket [DC IN 4.9V] (l 12)

7 LCD Monitor (l 15)

8 Memory Card Slot (l 14)

9 Card Slot Cover Open Lever (l 14)

10 Card Access Lamp [ACCESS] (l 79)

11 Multi-function Button

Operating/Select Function

[6/;/5/∫/1 SET] (l 18, 29, 30, 33)

Backlight Compensation [

ª] (l 35)

12 Menu Button [MENU] (l 18)

13 Recording/Playback Mode Selector Button

[REC/PLAY] (l 17)

14 Mode Selector Button [MODE] (l 17)

15 Microphone (built-in, stereo)

16 Reset Button [RESET] (l23, 87)

17 Speaker

18 Zoom Lever [T/W] (l 35)

Volume Adjustment Lever [rVOLs] (l 31)

19 Recording Start/Stop Button (l 27, 28, 32, 55)

20 AV Cradle Connector [MULTI] (l 13)

21 Strap Holder (l 68)

22 Power Lamp (l 12)

23 Power Switch [ON/OFF] (l 17)

24 Auto/Manual Selector Switch [AUTO/MANUAL/

SELECT] (l 36, 37)

1

2

3

4

5

6

7

11

12

13

14

8

9

10

17

18

19

21

23

22

24

20

16

15

Í

AV100PP.book 10 ページ２００３年８月２２日　金曜日　午後４時３０分

NN

25 White Balance Sensor (l 36)

26 Battery Compartment (l 12)

27 Battery Compartment Cover (l 12)

28 DC Input Socket [DC IN 4.9V] (l 13)

29 AV Input/Output Terminal [AV IN/OUT]

(l 54, 55)

30 Tray

31 Power Lamp [Í] (l 13)

32 Release Button (l 13)

33 Device Connector (l 13)

34 Mode Selector Button [MODE] (l 17)

35 Recording/Playback Mode Selector Button

[REC/PLAY] (l 17)

36 Menu Button [MENU] (l 18)

37 Multi-function Button

Operating/Select Function

[6/;/5/∫/1 SET] (l 18, 29, 30, 33)

38 Recording Start/Stop Button (l 27, 28, 32, 55)

39 Zoom Button [T/W] (l 35)

Volume Adjustment Button [rVOLs] (l 31)

25

26

27

30

31

32

33

35

34

36

37

38

39

28 29

AV100PP.book 11 ページ２００３年８月２２日　金曜日　午後４時３０分

NO

mçïÉê=pìééäó

ª Using AC Adaptor

N Open the DC Input Socket Cover and

connect the DC Input Lead to the [DC IN

4.9V] socket on the SD Video Camera.

O Connect the AC Cord to the AC Adaptor

and the AC Main socket.

ª Charging the Battery

Be sure to charge the supplied battery before use.

1 While pressing the A part, slide it to

remove the Battery Compartment Cover.

2 Press the terminals of the battery onto

the terminals of the Battery Compartment

and set the battery.

≥Fit the battery with its label facing upward.

≥After the battery is set, close the cover.

3 Connect the DC Input Lead to the [DC IN

4.9V] socket on the SD Video Camera.

4 Connect the AC Cord to the AC Adaptor

and the AC Main socket.

≥Power Lamp 1 flashes, and Charging starts.

≥When recharging, turn the power of the SD Video

Camera off.

5 Wait until Power Lamp 1 goes off.

≥When recharging is completed, Power Lamp 1

goes off.

≥If the Power Lamp flashes quickly (or slowly) when

recharging, recharging is not normal. (l 78)

≥For other notes, see pages 76, 78.

THE SOCKET OUTLET SHALL BE

INSTALLED NEAR THE EQUIPMENT AND

SHALL BE EASILY ACCESSIBLE.

CAUTION

Danger of explosion if battery is incorrectly

replaced.

Replace only with the same or equivalent type

recommended by the manufacturer.

Dispose of used batteries according to the

manufacturer’s instructions.

O

N

1

2

4

3

AV100PP.book 12 ページ２００３年８月２２日　金曜日　午後４時３０分

NP

cáííáåÖ=íÜÉ=`~ãÉê~=çå=íÜÉ=^s=

`ê~ÇäÉ

Fitting the Camera on the AV Cradle eases charging.

The AV Cradle allows the Camera to be connected to

the external device, such as a TV in order for the

pictures on this Device to be viewed on the TV.

≥The charging configuration is the same as the one for

connecting the DC Input Lead to the SD Video

Camera. (l 12)

N Open the [MULTI] Cover. A

O While pressing the Release Button, pull

out the tray.

P Place the SD Video Camera on the AV

Cradle.

≥If the DC Input Socket cover B is open, it is not

possible to fit the SD Video Camera on the AV

Cradle.

≥The grooves 1 of the SD Video Camera fit in the

leading protrusions 2.

Q Push the tray until you hear it click.

R Connect the DC Input Lead to the

[DC IN 4.9V] socket on the AV Cradle.

S Connect the AC Cord to the AC Adaptor

and the AC Main socket.

≥Power Lamp C flashes, and Charging starts.

≥When recharging, turn the power of the SD Video

Camera off.

≥When recharging is completed, Power Lamp

C

goes off.

≥Be sure to turn the SD Video Camera off before

fitting it on the AV Cradle.

≥If the AV Cable or AC Adaptor is connected to the SD

Video Camera, it is not possible to fit the SD Video

Camera on the AV Cradle.

Remove the SD Video Camera from the AV Cradle

While pressing the Release Button 1, pull out the tray

and remove the SD Video Camera 2.

≥For other notes, see page 79.

C

A

B

12

N

P

Q

RIS

O

1

2

AV100PP.book 13 ページ２００３年８月２２日　金曜日　午後４時３０分

NQ

fåëÉêíáåÖ=~=jÉãçêó=`~êÇ

An SD Memory Card can be used for this SD Video

Camera.

N Open the LCD Monitor and slide the Card

Slot Cover Open Lever to open the Card

Slot Cover.

O Hold the Memory Card placing the cut off

corner

1 at the front with the label 2

facing up, and then insert it fully into the

Memory Card Slot horizontally.

≥Turn off the SD Video Camera before inserting/

removing a Card.

P Close the Card Slot Cover securely.

ª Removing the Memory Card

Open the Card Slot Cover and press the center of

the Card

A and then pull it straight out B.

≥After removing the Card, close the Card Slot

Cover.

≥The SD Video Camera may be damaged if the

Card is forced out when the Card is fully inserted.

≥Keep the SD Memory Card out of the reach of

children to prevent swallowing.

≥For other notes, see page 79.

1

2

A

B

N

O

AV100PP.book 14 ページ２００３年８月２２日　金曜日　午後４時３０分

NR

rëáåÖ=íÜÉ=i`a=jçåáíçê

Record and play the video image while viewing the

LCD Monitor.

N Put your finger on the groove 1 to open

the LCD Monitor.

O Adjust the LCD Monitor angle according

to the desired recording/playing angle.

≥The LCD Monitor can rotate up to the angles

illustrated.

1: Up to 90

° maximum

2: Up to 130

° maximum

3: Up to 140

° maximum

4: Up to 130

° maximum

≥Forcefully rotating the LCD Monitor beyond these

ranges will damage the SD Video Camera.

≥If the position of the LCD Monitor is set to 2 or 4,

when you select the Recording Mode only the

indication which is limited (REC pause [¥;], REC

[¥] or Warning [°]) appears on screen display.

If you desired the indication returned to normal, set

position of the LCD Monitor to 1 or 3.

≥The LCD image may appear slightly brighter than the

actual recorded image. This is done intentionally to

provide better visibility when the camera is used

outdoors in bright sunlight.

≥For other notes, see page 79.

ª Vertical Style and Horizontal Style

This SD Video Camera can be used in 2 styles.

1 Vertical Style: Use mainly when recording.

2 Horizontal Style: Use mainly when playing back.

1

2

3

4

1

NIO

1

2

AV100PP.book 15 ページ２００３年８月２２日　金曜日　午後４時３０分

NS

ª Portrait Picture Recording

By opening the LCD Monitor and turning it so that it

faces forward (to the lens side), you can let the subject

in front of the SD Video Camera monitor the shot while

shooting is in progress.

≥If you set the LCD Monitor to this position, an image

on the LCD Monitor will be reversed when displayed.

However, recording images are recorded normally.

≥If a general Warning indication [°] appears, return

the LCD Monitor to the Vertical style in order to verify

contents. (l 71)

ª Using the Multi-function Button

In this SD Video Camera, the Multi-function Button is

tilted to the right to 45 degrees in order to make it easy

to do operation in both the Vertical and Horizontal

Style.

Move the cursor and selection of the item on the

display by the Multi-function Button of main unit:

A: 6 (LEFT)

B: ∫ (DOWN)

C: ; (UP)

D: 5 (RIGHT)

D

CA

B

AV100PP.book 16 ページ２００３年８月２２日　金曜日　午後４時３０分

NT

qìêåáåÖ=íÜÉ=mçïÉê=låL

pÉäÉÅíáåÖ=léÉê~íáçå=jçÇÉë

Select a desired mode on the mode selection screen.

N Set the Power Switch to [ON].

≥The SD Video Camera is turned on.

O Press the [REC/PLAY] Button to select

Recording Mode or Playback Mode.

1: Recording Mode

2: Playback Mode

P Press the [MODE] Button to select a

Operation Mode.

≥Every time the [MODE] Button is pressed, the

Operation Mode changes as follows.

1: Recording Mode

2: Playback Mode

≥For other notes, see page 79.

ª About the Operation Modes

Six operation modes are provided as follows.

Motion image [MPEG2]:

Motion image (MPEG2 format) recording mode

(l 27)

Motion image (MPEG2 format) playback mode

(l 29)

Motion image [MPEG4]:

Motion image (MPEG4 format) recording mode

(l 28)

Motion image (MPEG4 format) playback mode

(l 30)

Still picture [PICTURE]:

Still picture (JPEG format still picture) recording

mode (l 32)

Still picture (JPEG format still picture) playback mode

(l 33)

≥When you use the battery to supply the power with

the SD Video Camera, it is automatically turned off if

you leave it for more than approx. 5 minutes without

any operation.

SET/

g

SET/

O

12

P

12

Í

N

SET/

g

AV100PP.book 17 ページ２００３年８月２２日　金曜日　午後４時３０分

NU

rëáåÖ=íÜÉ=jÉåì=pÅêÉÉå

Allows the functions usable in the selected mode to be

set from the menu.

N Select a desired mode. (l 17)

O Press the [MENU] Button.

≥The Main Menu in the selected mode is

displayed.

P Press the ;/∫ side of the Multi-function

Button to select a desired Main Menu and

press the [1 SET] Button.

≥The Sub-Menu in the selected mode is

displayed.

Q Press the ;/∫ side of the Multi-function

Button to select a desired Sub-Menu and

then press the [1 SET] Button.

R Press the ;/∫ side of the Multi-function

Button to select a desired item and then

press the [1 SET] Button.

S Press the [MENU] Button.

≥Menu screen disappears, and the selected item

is now being set.

Return to the menu one before

Press the 6 side of the Multi-function Button.

≥Press the [MENU] Button when playing back the

motion image or still picture to edit the file being

played back.

≥When you do not perform operation the menu screen

automatically disappears if you leave it for more than

approx. 1 minutes.

≥For other notes, see page 79.

g

SET/

Menu

g

SET/

Menu

g

SET/

Menu

g

P

O

QIR

S

N

AV100PP.book 18 ページ２００３年８月２２日　金曜日　午後４時３０分

NV

iáëí=çÑ=jÉåìë

The menu images used differ slightly from the actual

menus. These are offered for simplified illustration

purposes.

ª Recording Mode

Camera Functions Setup

1 Auto Exposure Mode [Program AE] (l 38)

2 Image Stabilizer [EIS] (l 39)

3 Digital Zoom [Dig. Zoom] (l 35)

4 Wind Noise Reduction [Wind Cut] (l 39)

≥This function appears [MPEG2] mode and

[MPEG4] mode.

Record Functions Setup

5 Picture Quality [Quality] (l 27, 28, 32)

6 Input Source [Input Source] (l 55)

Date Setup

7 Date and Time Indication Mode [Date Mode]

(l 23)

8 Date and Time Indication [Indication] (l 23)

9 Date and Time Setting [Date Set] (l 22)

Display Setup

10 OSD Indication [OSD Output] (l 25)

11 LCD Brightness Adjustment [LCD Bright]

(l 24)

12 LCD Color Adjustment [LCD Color] (l 24)

Initial Setup

13 Beep Sound [Beep]

≥This SD Video Camera will emit sound when the

power switch is changed over, the REC Button is

pressed, or other operations are engaged. If you

do not need operating sound, you can switch it

off.

14 Recording LED [Record LED]

≥The Recording Lamp which is on the front of the

SD Video Camera lights while recording, and

also flashes during remote control receiving.

When [Record LED] set to [Off], the Recording

Lamp will not light.

14

13

g

11

12

10

g

1

2

3

4

5

6

9

7

8

AV100PP.book 19 ページ２００３年８月２２日　金曜日　午後４時３０分

OM

ª Playback Mode

[MPEG2/MPEG4] mode

Scene

1 Deleting a Scene [Delete] (l 40)

2 Setting the Lock [File Lock] (l 41)

3 Scene Detail [Detail] (l 41)

PlayList*

4 Selecting and switching a Play List [Switch]

(l 43)

5 Playing back the Play List [Play] (l 44)

6 Creating the Play List [Create] (l 43)

7 Editing the Play List [Edit] (l 44)

8 Edit a title of the Play List [Title] (l 46)

9 Deleting a Play List [Delete] (l 47)

Program*

10 Switching a Program [Switch] (l 48)

11 Playing back the Program [Play] (l 48)

12 Edit a title of the Program [Title] (l 49)

Go To

13 Go to Top of List [Top] (l 50)

14 Go to End of List [End] (l 50)

*[MPEG2] mode only.

1

2

3

ETC.

4

5

6

7

8

9

ETC.

10

11

12

ETC.

g

ETC.

13

14

AV100PP.book 20 ページ２００３年８月２２日　金曜日　午後４時３０分

La pagina sta caricando ...

Panasonic SVAV100 Manuale del proprietario

Panasonic SVAV100 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti