MGE UPS Systems PULSAR EVOLUTION 3000 XL Manuale utente

3400711500/AA

MGE UPS SYSTEMS

Installation and user

manual

English

Français

Deutsch

Italiano

Español

Nederlands

Pulsar Evolution

2200/3000/3000 XL

N

O

T

HI

N

G

W

I

L

S

T

O

P

Y

O

U

N

OW

www.mgeups.com

34007115EN/AA - Page 1

Installation and user

manual

www.mgeups.com

N

O

T

H

I

N

G

W

I

L

S

T

O

P

Y

O

U

N

O

W

MGE UPS SYSTEMS

Pulsar Evolution

2200/3000/3000 XL

Page 2 - 34007115EN/AA

34007115EN/AA - Page 3

Introduction

Thank you for selecting an MGE UPS SYSTEMS product to protect your electrical equipment.

The Pulsar Evolution range has been designed with the utmost care. We recommend that you take the time to read this

manual to take full advantage of the many features of your UPS.

MGE UPS SYSTEMS pays great attention to the environmental impact of its products. Measures that have made Pulsar

Evolution a reference in environmental protection include:

◗ the eco-design approach used in product development,

◗ recycling of Pulsar Evolution at the end of its service life.

To discover the entire range of MGE UPS SYSTEMS products and the options available for the Pulsar Evolution range,

we invite you to visit our web site at www.mgeups.com or contact your MGE UPS SYSTEMS representative.

Page 4 - 34007115EN/AA

Foreword

Using this document

Important instructions that must always be followed.

Information, advice, help.

Visual indication.

Action.

Audio indication.

In the illustrations on the following pages, the symbols below are used:

LED off.

LED on.

LED flashing.

Information may be found in two ways, using:

◗ the contents;

◗ the index.

Pictograms

34007115EN/AA - Page 5

Contents

1. Presentation

1.1 Overall view ................................................................................................................................. 7

Tower position ................................................................................................................................. 7

Rack position .................................................................................................................................. 7

1.2 Back ............................................................................................................................................. 8

1.3 Control panel ................................................................................................................................. 9

2. Installation

2.1 Unpacking and parts check ....................................................................................................... 10

2.2 Upright installation (tower position) ......................................................................................... 11

2.3 Flat installation (rack position) .................................................................................................. 12

2.4 Connecting the protected equipment ....................................................................................... 13

2.5 Connection to the RS232 or USB communications port (optional)......................................... 14

2.6 Connection to the data-line protection port (optional) ............................................................. 14

2.7 Installation of the communications-card option ...................................................................... 15

3. Operation

3.1 Start-up ........................................................................................................................................ 16

3.2 Shift to booster or fader mode (during voltage variations in the AC-input power)..................... 16

3.3 Operation on battery power (following failure of AC-input power) ............................................. 17

Transfer to battery power .............................................................................................................. 17

Threshold for the low-battery warning...........................................................................................17

3.4 Personalisation (optional) ........................................................................................................... 18

Function ........................................................................................................................................ 18

ON / OFF conditions tab ............................................................................................................... 18

Battery tab..................................................................................................................................... 18

Voltage-thresholds tab .................................................................................................................. 19

Sensitivity tab ................................................................................................................................ 19

4. Maintenance

4.1 Trouble-shooting......................................................................................................................... 20

4.2 Replacement of the battery module .......................................................................................... 21

5. Environment ..................................................................................................................................... 23

Page 6 - 34007115EN/AA

Contents

6. Appendices

6.1 Technical data ............................................................................................................................. 24

Simplified diagram ........................................................................................................................ 24

Technical characteristics ............................................................................................................... 25

Examples of battery backup times ................................................................................................26

6.2 Glossary....................................................................................................................................... 27

6.3 Index............................................................................................................................................. 28

34007115EN/AA - Page 7

1. Presentation

1.1 Overall view

Tower position

Rack position

Evolution 2200

Evolution 3000

Evolution 3000 XL

Evolution 2200

Evolution 3000

Evolution 3000 XL

Dimensions in mm

(W x H x D)

438 x 87.9 x 640

(19") (2U)

Weight in kg

34

37

21

P U L S A R

Evolution

3 0 0 0

P U L S A R

Evolution

3 0 0 0

W

H

D

Page 8 - 34007115EN/AA

1 2

IN OUT

Ue/In/Eing 230V/16A Max

DATA LINE PROTECTION

AB

1

2

Us/Out/Ausg I max 13A

AB

TO BATTERY

CABINET

RS232

1 2

IN OUT

Ue/In/Eing 230V/10A Max

TO BATTERY

CABINET

DATA LINE PROTECTION

Us/Out/Ausg I max 10A

RS232

1. Presentation

1.2 Back

Pulsar Evolution 3000 / 3000 XL

Pulsar Evolution 2200

USB communications port.

RS232 communications port.

Connector for automatic detection of an

additional battery module.

Data-line protection.

Slot for communications-card option.

Connector for an additional battery

module.

Output circuit breakers.

Four outlets for direct connection of

protected equipment.

Two groups of two programmable

outlets (groups 1 and 2).

Input circuit-breaker.

Socket for connection to AC-power

source.

Battery module connectors (to the UPS

or to other battery modules).

Connectors for automatic detection of

additional battery modules.

Circuit breaker for battery ON/OFF and

protection.

1

2

3

4

5

6

7

9

8

10

11

12 14

EXB additional battery module 12

13

14

13 12

7

1234 115 1098

12

6

1234 115 109

8

12

6

34007115EN/AA - Page 9

12

%

1.3 Control panel

Bargraph indicating percent load at output.

Group 1 programmable outlets supplied with power.

Iluminated ON/OFF button for the outlets.

Group 2 programmable outlets supplied with power.

Operation on battery power.

15

16

17

20

19

23

22

18

21

1. Presentation

UPS fault.

Battery fault.

Overload.

Booster or fader mode.

Bargraph indicating the battery charge level.

0 to 25%.

26 to 50%.

51 to 75%.

76 to 100%.

Page 10 - 34007115EN/AA

2. Installation

2.1 Unpacking and parts check

Cord for connection to the AC-power source for 3000/3000 XL versions only (for the 2200 version, use the power cord

of the protected equipment).

Two cords for connection of the protected equipment.

RS232 communications cable.

USB communications cable.

Telescopic rails for mounting in 19" bay with mounting hardware.

Two securing systems for equipment power cords.

CD-ROM with the Solution-Pac and UPS Driver software.

Product documentation.

Two supports for the upright position.

27

28

29

25

24

25

26

27

28

26

24

29

31

32

31

32

30

P U L S A R

Evolution

3 0 0 0

34007115EN/AA - Page 11

2. Installation

2.2 Upright installation (tower position)

Connect the two supports for the upright position.

P U L S A R

Evolution

3 0 0 0

P U L S A R

Evolution

3 0 0 0

Page 12 - 34007115EN/AA

2. Installation

2.3 Flat installation (rack position)

Follow steps 1 to 6 for rack mounting of the UPS on the rails.

The rails and the necessary mounting hardware are supplied by MGE UPS SYSTEMS.

1

2

5

3

6

5

4

3

P U L S A R

Evolution

3 0 0 0

34007115EN/AA - Page 13

Ue/In/Eing 230V/10A Max

1 2

Us/Out/Ausg I max 10A

2.4 Connecting the protected equipment

Check that the indications on the rating plate on the back of the UPS correspond to your AC-power system and to

the actual electrical consumption of all the equipment to be connected to the UPS.

1 - Remove the power cord supplying the

equipment to be protected.

2 - Pulsar Evolution 2200: Connect the

power cord (1) just removed from the

equipment to the AC-power socket 11 and

then to the AC-power wall outlet.

- Pulsar Evolution 3000/3000 XL: Connect

the supplied power cord 24 (250 V, 16 A) to

the AC-power socket 11 and then to the

AC-power wall outlet.

3 - Connect the protected equipment to the

UPS using the two cords 25 . It is advised

to connect priority loads to the four standard

outlets 8 and any non-priority loads to the

four programmable outlets 9 (in groups of

two outlets).

If the UPS is connected to a

computer running MGE

communications software, it is

possible to program the

interruption of power to the

programmable outlets 9 during

operation on battery power, thus

reserving backup power for the

priority loads.

4 - Lock the connections using the securing

system 29 .

25

8

9

1

2

2. Installation

11

29

As soon as the UPS is energised, the battery begins charging. Eight hours are required to charge to the full rated

backup time.

Pulsar Evolution 3000 XL: At least one EXB additional battery module must be connected to the UPS because it does not

have internal batteries. See the EXB battery-module installation manual (Doc. no. 3400711600) for information on making

the connections.

(1) Make sure the cord has the following

characteristics: 250 V, 10 A, cross-sectional area 1

mm2, type HO5.

Page 14 - 34007115EN/AA

IN OUT

DATA LINE PROTECTION

TO BATTERY

CABINET

RS232

2. Installation

2.5 Connection to the RS232 or USB communications port (optional)

1 - Connect the RS232 26 or USB 27

communications cable to the serial port or

the USB port on the computer.

2 - Connect the other end of the

communications cable 26 or 27 to the

RS232 2 or USB 1 communications

port on the UPS.

The UPS can now communicate with all

MGE UPS SYSTEMS supervision, set-up or

safety software.

26

27

The RS232 and USB

communications ports cannot

operate simultaneously.

2.6 Connection to the data-line protection port (optional)

The data-line protection function on the UPS

eliminates overvoltages flowing on the

computer-network lines.

Simply connect the line to be protected to

the UPS using the data-line protection

connectors (IN and OUT) as indicated

opposite (RJ45 cables not supplied).

1

2

IN OUT

TO BATTERY

CABINET

DATA LINE PROTECTION

RS232

34007115EN/AA - Page 15

2. Installation

2.7 Installation of the communications-card option

1 - Remove the slot cover 5 secured by

two screws.

2 - Insert the card in the slot.

3 - Secure the cover with the two screws.

Slot for the communications-card

option.

5

IN OUT

TO BATTERY

CABINET

DATA LINE PROTECTION

RS232

It is not necessary to shut down the UPS to install the communications card.

Page 16 - 34007115EN/AA

12

%

3. Operation

3.1 Start-up

15

16

17

Press the ON / OFF button 15 .

The buzzer beeps and all the LEDs come ON.

The buzzer beeps twice during the self-test, then button 15 remains

ON, indicating that the outlets are supplied with power.

- AC power is present: Only button 15 is ON. The protected

equipment is supplied by the AC-power source.

- AC power is absent: Button 15 and LED 16 are ON. The protected

equipment is supplied by the UPS, operating on battery power.

All the connected equipment is supplied with power.

12

%

3.2 Shift to booster or fader mode

(during voltage variations in the AC-input power)

21

The booster and fader functions maintain the output voltage supplied by

the UPS within close tolerances around the rated value even if

significant voltage variations occur in the AC-input power. This avoids

calling on battery power.

The values defining the voltage range may be set using the UPS Driver

software.

During operation in booster or fader mode, LED 21 is ON, signalling a

significant voltage variation in the AC-input power.

If button 15 or LED 16 are not ON or if LED 17 is ON, there is a fault (see section 4.1).

Note: The battery is charged as soon as the UPS is connected to the AC-power source, even if button 15 is in the OFF

position.

34007115EN/AA - Page 17

12

%

12

%

3. Operation

3.3 Operation on battery power (following failure of AC-input power)

Transfer to battery power

The AC-input power is out of tolerances, LED 16 goes ON.

During operation on battery power, the buzzer beeps every ten seconds.

The equipment connected to the UPS is supplied by the battery.

Threshold for the low-battery warning

When the threshold is reached, the buzzer beeps every three seconds.

The low-battery warning threshold can be set by the user, with the “UPS

Driver” software.

There is very little remaining battery backup time. Close all

applications because UPS automatic shutdown is imminent.

When the battery reaches the end of its backup time, the UPS shuts

down and all the LEDs go OFF.

The equipment is no longer supplied with power.

16

The UPS automatically restarts when power returns.

If the UPS does not restart, check that the “automatic restart when power returns” function has not been disabled (see

section 3.4 Personalisation).

16

Page 18 - 34007115EN/AA

3. Operation

3.4 Personalisation (optional)

Function

Configurable function

Automatic restart

Cold start

Forced reboot

Energy saving

UPS ON / OFF via software

Default setting

Enabled

Disabled

Enabled

Personalisation parameters can be set and modified using the UPS Driver software installed on a computer that is

connected to the UPS (see section 2.5 Connection to the RS232 communications port).

Check that the RS232 26 communications cable is connected.

UPS Driver installation:

1 - Insert the Solution-Pac CD-ROM containing the UPS Driver software in the drive of a PC running Windows.

2 - Open the Windows File manager or Explorer and select the CD-ROM drive.

3 - Double-click "\Emb\Evolutio\Config\Setup.exe".

Once UPS Driver has been installed, UPS parameters can be modified in a window containing a number of tabs, each

presenting a set of parameters :

Battery tab

Configurable function

Interval between automatic battery tests

Low-battery warning threshold

Configuration of additional battery modules

Protection against deep discharges

Default setting

Once a week

20% of the remaining battery

backup time

Display the number of standard

EXB modules connected

to the UPS

Enabled

Options

Every day

Once a month

No test

10 to 40% of the remaining battery

backup time

Back-up time for non-standard

batteries (for 3000XL only)

Disabled

Options

Disabled

Enabled

Disabled

ON / OFF conditions tab

34007115EN/AA - Page 19

3. Operation

Configurable function

Output voltage on battery power

Upper threshold for transfer to battery power

Fader-mode cut-in threshold

Booster-mode cut-in threshold

Lower threshold for transfer to battery power

Maximum input-voltage range

Default setting

230 V

294 V

265 V

184 V

160 V

Disabled

Options

200 V - 220 V - 240 V

271 to 294 V

244 to 265 V

184 to 207 V

160 to 180 V

Enabled (1)

Configurable function

UPS sensitivity level

Default setting

Normal

Options

High or low

Voltage-thresholds tab

Sensitivity tab

For more informations about these settings, refer to the Help function of the "UPS Driver" software.

(1) Lower threshold for transfer to battery power = 150 V

La pagina sta caricando ...

MGE UPS Systems PULSAR EVOLUTION 3000 XL Manuale utente

Questo manuale è adatto anche per

MGE UPS Systems PULSAR EVOLUTION 3000 XL Manuale utente

in altre lingue

Documenti correlati

Altri documenti