Eaton Evolution 1150 Rack Manuale utente

www.eaton.com

Installation and user

manual

English

Français

Deutsch

Italiano

Español

Nederlands

Evolution

650 / 650 Rack 1U

850 / 850 Rack 1U

1150 / 1150 Rack 1U

1550 / 1550 Rack 1U

Pulsar Series

3400823500/AC

www.eaton.com

_

Installation and user

manual

Evolution

650/650 Rack 1U

850/850 Rack 1U

1150/1150 Rack 1U

1550/1550 Rack 1U

Pulsar Series

34008235EN/AC - Page 2

34008235EN/AC - Page 3

Introduction

Environmental protection

EATON has implemented an environmental-protection policy.

Products are developed according to an eco-design approach.

Substances

This product does not contain CFCs, HCFCs or asbestos.

Packing

To improve waste treatment and facilitate recycling, separate the various packing components.

◗ The cardboard we use comprises over 50% of recycled cardboard.

◗ Sacks and bags are made of polyethylene.

◗ Packing materials are recyclable and bear the appropriate identification symbol .

Follow all local regulations for the disposal of packing materials.

End of life

EATON will process products at the end of their service life in compliance with local regulations.

EATON works with companies in charge of collecting and eliminating our products at the end of their service life.

Product

The product is made up of recyclable materials.

Dismantling and destruction must take place in compliance with all local regulations concerning waste.

At the end of its service life, the product must be transported to a processing centre for electrical and electronic waste.

Battery

The product contains lead-acid batteries that must be processed according to applicable local regulations concerning

batteries.

The battery may be removed to comply with regulations and in view of correct disposal.

Thank you for selecting an EATON product to protect your electrical equipment.

The Evolution range has been designed with the utmost care.

We recommend that you take the time to read this manual to take full advantage of the many features of your UPS

(Uninterruptible Power System).

Before installing Evolution, please read the booklet presenting the safety instructions. Then follow the indications in

this manual.

To discover the entire range of EATON products and the options available for the Evolution range, we invite you to

visit our web site at www.eaton.com or contact your EATON representative.

Material Abbreviation Number

in the symbol

Polyethylene terephthalate PET 01

High-density polyethylene HDPE 02

Polyvinyl chloride PVC 03

Low-density polyethylene LDPE 04

Polypropylene PP 05

Polystyrene PS 06

34008235EN/AC - Page 4

Introduction

Pictograms

Important instructions that must always be followed.

Information, advice, help.

Visual indication.

Action.

Audio signal.

In the illustrations on the following pages, the symbols below are used:

LED off

LED on

LED flashing

34008235EN/AC - Page 5

Contents

1. Presentation

1.1 Standard positions ...................................................................................................................... 6

Tower models ................................................................................................................................ 6

Rack models................................................................................................................................... 6

1.2 Rear panels................................................................................................................................... 7

Evolution 650/850/1150/1550......................................................................................................... 7

Evolution 650/850/1150/1550 Rack ................................................................................................7

1.3 Control panel................................................................................................................................7

2. Installation

2.1 Unpacking and contents check................................................................................................... 8

2.2 Installation of tower model......................................................................................................... 9

2.3 Installation of rack model ........................................................................................................... 9

2.4 Installation 650 rack model........................................................................................................10

2.5 Communication ports.................................................................................................................11

Connection of RS232 or USB communication port (optional) .......................................................11

Installation of the communication cards (optional) .......................................................................11

Characteristics of the contact communication port (optional) ......................................................11

2.6 Equipment connections .............................................................................................................12

3. Operation

3.1 Start-up and normal operation..................................................................................................13

3.2 Operation on battery power ......................................................................................................13

3.3 Return of AC input power ..........................................................................................................13

3.4 UPS shutdown ............................................................................................................................14

3.5 UPS remote-control functions...................................................................................................14

4. Measurements and personalisation15

5. Maintenance

5.1 Troubleshooting ..........................................................................................................................16

5.2 Replacing the battery module in the tower model..................................................................16

Safety recommendations..............................................................................................................16

Battery-module removal................................................................................................................16

Mounting the new battery module ...............................................................................................17

5.3 Replacing the battery module in the rack model.....................................................................17

Safety recommendations..............................................................................................................17

Battery-module removal................................................................................................................17

Mounting the new battery module ...............................................................................................18

5.4 Training centre.............................................................................................................................18

6. Appendices

6.1 Technical specifications..............................................................................................................19

6.2 Glossary ...................................................................................................................................... 20

34008235EN/AC - Page 6

1. Presentation

1.1 Standard positions

Tower models

Rack models

Dimensions (H x W x D)

in mm

Evolution 650 234 x 147 x 418

Evolution 850 234 x 147 x 418

Evolution 1150 234 x 147 x 418

Evolution 1550 234 x 147 x 492

Weights in kg

Evolution 650 8.4

Evolution 850 10.8

Evolution 1150 12.5

Evolution 1550 16.5

Dimensions (H x W x D)

in mm

Evolution 650 Rack 43.5 x 438 x 366

Evolution 850 Rack 43.5 x 438 x 512

Evolution 1150 Rack 43.5 x 438 x 512

Evolution 1550 Rack 43.5 x 438 x 556

Weights in kg

Evolution 650 Rack 10.1

Evolution 850 Rack 16.1

Evolution 1150 Rack 16.6

Evolution 1550 Rack 20

34008235EN/AC - Page 7

1. Presentation

1.2 Rear panels

Evolution 650/850/1150/1550

Evolution 650/850/1150/1550 Rack

1.3 Control panel

Bargraphs (8) and (11)

(1) Slot for optional communication card

(2) Socket for connection to AC-power

source

(3) 2 outlets for connection of equipment

(4) RS232 communication port

(5) 2 programmable outlets (1 and 2) for

connection of equipment

(6) USB communication port

(7) Connector for remote ON/OFF and RPO

(Remote Power Off) control

(8) Bargraph indicating the percent load

(9) Programmable outlet 1 is supplied

(10) ON/OFF button for UPS and outlets

(11) Bargraph indicating battery-charge

level

(12) Programmable outlet 2 is supplied

(13) Load protected LED

(14) Downgraded operation LED

(15) Load not protected LED

230V/10A Max

RS232

ROO RPO

1

2

Ue/In/Eing

Us/Out/Ausg

I max 6.5A

2

3

5

1

4

6

7

2

4 6 7

1

3 5

2

4 6 7

1

3 5

Evolution 650/850/1150 Rack

Evolution 1550 Rack

2

1

2

9

10

12

13

14

15

11

8

25

50 75 100

%min max

34008235EN/AC - Page 8

2. Installation

2.1 Unpacking and contents check

(16) Evolution UPS, tower or rack model

(17) 2 connection cables for the protected equipment

(18) Documentation

(19) Solution-Pac CD-ROM

(20) RS232 communication cable

(21) USB communication cable

(22) Mounting kit for 19-inch bays (rack model only,

except 650 Rack)

(23) System to secure power plugs (rack model only)

Packing materials must be disposed of in compliance with all local regulations concerning waste.

Recycling symbols are printed on the packing materials to facilitate sorting.

34008235EN/AC - Page 9

2. Installation

2.2 Installation of tower model

2.3 Installation of rack model

Follow steps 1 to 4 for module mounting on the rails.

The rails and necessary hardware are supplied by EATON.

34008235EN/AC - Page 10

2. Installation

2.4 Installation of the 650 rack model

Follow steps 1 to 3 for rack mounting.

The necessary hardware is supplied by EATON.

34008235EN/AC - Page 11

2. Installation

2.5 Communication ports

Connection of RS232 or USB communication port (optional)

Installation of the communication cards (optional)

Characteristics of the contact communication port (optional)

The RS232 and USB communication ports cannot operate simultaneously.

1 - Connect the RS232 (20) or USB (21)

communication cable to the serial or USB

port on the computer equipment.

2 - Connect the other end of the

communication cable (20) or (21) to the

USB (6) or RS232 (4) communication port

on the UPS.

The UPS can now communicate with

EATON power management software.

Limited-access slot for the

communication card

It is not necessary to shutdown the UPS

before installing a communication card.

1 - Remove the slot cover (1) secured by

screws.

2 - Insert the communication card in the

slot.

3 - Secure the card cover with the two

screws.

◗ Pins 1, 2, 3, 5, 6: not used

◗ Pin 4: common (user)

◗ Pin 7: low battery

◗ Pin 8: UPS ON, equipment supplied

◗ Pin 9: operation on battery power

n.o.: normally open contact

When a signal is activated, the contact is closed between the common (pin 4) and the pin for the corresponding

signal.

Contact characteristics (optocoupler)

◗ Voltage: 48 V DC max

◗ Current: 25 mA max

◗ Power: 1.2 W

21

20

RS232

ROO RPO

1

2

Us/Out/Ausg

I max 6.5A

4

6

230V/10A Max

RS232

1

Ue/In/Eing

1

5432

9876

1

commun

4

n.o.

n.o.n.o.

34008235EN/AC - Page 12

2. Installation

2.6 Equipment connections

Check that the indications on the name plate located on the back of the UPS correspond to the AC-power source

and the true electrical consumption of the total load.

1 - Disconnect the supply cable

(1)

(not

supplied) of the equipment.

2 - Connect the cable to socket (2), then to

the AC-power source.

3 - Connect the loads to the UPS using the

cables (17).

It is preferable to connect the priority loads

to the two outlets marked (3) and the non-

priority loads to the two programmable

outlets marked (5) (1 and 2).

To program shutdown of outlets (5) during

operation on battery power and thus

optimise the available backup time, the

EATON communication software is

required.

(1) Cable characteristics: 250 V - 10 A (CSA

1mm

2

, type HO5).

Fit the connection securing system. (rack model only).

4 - Fit the connection securing system (23)

that prevents the plugs from being pulled

out accidentally.

Note. The UPS charges the battery as soon as it is connected to the AC-power source, even if button (10) is not

pressed.

Once the UPS is connected to the AC-power source, eight hours of charging are required before the battery can

supply the rated backup time.

24

17

23

17

34008235EN_AC.fm Page 12 Mercredi, 12. novembre 2008 8:30 08

34008235EN/AC - Page 13

3. Operation

3.1 Start-up and normal operation

3.2 Operation on battery power

Transfer to battery power

Low-battery warning

End of battery backup time

3.3 Return of AC input power

Following an outage, the UPS restarts automatically when AC input power returns (unless the restart function has

been disabled via UPS personalisation) and the load is again supplied.

Press button (10) for approximately 1 second.

◗ The buzzer beeps once and all the LEDs go ON simultaneously.

◗ If AC input power is available, button (10) and LED (13) are ON. The

load is supplied by the AC-power source. Conditions permitting, the

UPS runs a battery test, indicated by LEDs (11) and the buzzer.

◗ If AC input power is not available, button (10) and LEDs (13) and (14)

are ON. The load is supplied by the UPS on battery power.

The connected devices are protected by the UPS.

If LED (15) is ON, a fault has occurred (see the

"Troubleshooting"

section).

◗ The connected devices continue to be supplied by the UPS when AC

input power is no longer available. The necessary energy is provided

by the battery.

◗ Button (10) and LEDs (13) and (14) are ON.

◗ The audio alarm beeps every ten seconds.

The connected devices are supplied by the battery.

◗ Button (10) and LEDs (13) and (14) are ON.

◗ The audio alarm beeps every three seconds.

The remaining battery power is low.

Shut down all applications on the connected equipment because

automatic UPS shutdown is imminent.

◗ All the LEDs go OFF.

◗ The audio alarms stops.

The UPS is completely shut down.

1

2

10

13

14

15

11

1

2

10

13

14

1

2

10

13

14

34008235EN/AC - Page 14

3. Operation

3.4 UPS shutdown

3.5 UPS remote-control functions

Remote control connection and test

Press button (10) for approximately 2 seconds.

The devices connected to the UPS are no longer supplied.

Evolution offers a choice between two remote control functions.

◗ RPO (Remote Power Off) allows a remote contact to be used to

disconnect all the equipment connected to the UPS.

Restarting the UPS requires manual intervention.

◗ ROO (Remote ON/OFF) allows remote action of button (10) to shut

down the UPS.

These functions are obtained by opening of the contact connected

between the appropriate pins of connector (7) on the rear panel of the

UPS (see figures below).

1 - Check that the UPS is OFF and disconnected from the AC input source.

2 - Remove connector (7) after unscrewing the screws.

3 - Connect a normally closed volt-free contact (60 V DC / 30 V AC max., 20 mA max., 0.75 mm

2

cable cross-section)

between the two pins of connector (7) (see diagram).

Contact open: UPS shutdown

Contact closed: UPS start-up (UPS connected to AC power and AC power is available)

Note. The local ON/OFF control using button (10) overrides the remote-control function.

Contact open: UPS shutdown, LED (14) goes ON.

To return to normal operation, deactivate the remote external contact and restart the UPS

by pressing button (10).

4 - Plug connector (7) into the back of the UPS.

5 - Connect and restart the UPS following the previously described procedures.

6 - Activate the external remote shutdown contact to test the function.

Warning. This connector must only be connected to SELV (Safety Extra-Low Voltage) circuits.

1

2

10

230V/10A Max

RS232

ROO RPO

1

2

Ue/In/Eing

Us/Out/Ausg

I max 6.5A

7

ROO

7

RPO

34008235EN/AC - Page 15

4. Access to measurements and personalisation data

Main-output personalisation

Voltage-threshold personalisation

(1) Low threshold for transfer to battery: 150 V.

UPS-sensitivity personalisation

UPS ON/OFF personalisation

Battery personalisation

◗ Insert the Solution-Pac CD-ROM in the drive.

◗ On the first navigation screen, select "Point to Point solution" and follow the instructions on how to install the

Personal Solution-Pac software.

◗ Then select "Settings", "Advanced settings" and "UPS settings".

Note that the Linux/Unix/MacOS versions of Personal Solution-Pac software do not offer this possibility.

It is possible to modify the settings listed below (detailed comments are available in the Personal Solution-Pac

software).

Function Factory setting Other available settings

Output voltage

on battery power 230 Volts AC 200/208/220/240 Volts AC

Overload alarm threshold 105% 30/50/70%

Function Factory setting Other available settings

High threshold for transfer to battery 294 Volts AC 271 to 294 Volts AC

Low threshold for transfer to battery 160 Volts AC 160 to 180 Volts AC

Fader activation threshold 265 Volts AC 244 to 265 Volts AC

Booster activation threshold 184 Volts AC 184 to 207 Volts AC

Maximum input-voltage range Disabled Enabled

(1)

Function Factory setting Other available settings

UPS-sensitivity level Normal High or low

Function Factory setting Other available settings

Automatic start Enabled Disabled

Cold start Enabled Disabled

Forced shutdown Enabled Disabled

Energy-savings mode Disabled Enabled

UPS ON/OFF controlled by software Enabled Disabled

Battery level before restart 0% 0 to 100%

Function Factory setting Other available settings

Battery-test intervals Weekly No test / daily test / monthly

test

Low-battery warning 20% 0 to 100%

Battery protection against deep discharge Enabled Disabled

Audio alarm Enabled Disabled

34008235EN/AC - Page 16

5. Maintenance

5.1 Troubleshooting

5.2 Replacing the battery module in the tower model

Safety recommendations

The battery can cause electrocution and high short-circuit currents. The following safety precautions are required

before servicing the battery components:

◗ Remove watches, rings, bracelets and all other metal objects from the hands and arms,

◗ Use tools with an insulated handle.

Battery-module removal

Indication Diagnostic Correction

1 When the UPS is started using button

(10), all the LEDs go ON once and the

buzzer beeps once, then LED (14)

remains ON.

The remote power off (RPO)

contact has been activated to shut

down the UPS and now prevents

restart.

Set the contact back to its normal

position and press button (10) to

restart.

2 Button (10) and LEDs (13) and (14) are

ON and all the LEDs on bargraph (8)

flash.

The percent load is greater than

the set overload level or UPS

capacity.

Check the power drawn by the

connected devices and disconnect

any non-priority devices. Check

the overload level setting.

3 Button (10) and LED (15) are ON and

all the LEDs on bargraph (8) are

flashing.

A critical overload has occurred

on the UPS output. If AC input

power fails, the load will not be

supplied in battery mode.

Check the power drawn by the

connected devices and disconnect

any non-priority devices.

4 LED (15) is ON and all the LEDs on

bargraph (11) are flashing.

A battery fault has been detected

during the automatic test.

Replace the battery module (see

section 5.2, Battery-module

replacement).

5 LED (15) alone is ON and the buzzer

sounds continuously.

A UPS internal fault has occurred

and the load is not supplied.

Call the after-sales support

department.

The UPS must be turned as shown in the

figure opposite.

A - Remove the two screws on the left-

hand side.

B - Lift and pull away the panel with the

logo.

C - Pull on the two connectors to

disconnect the battery (never pull on the

wires).

D - Pull the plastic tab to remove the

battery.

C

D

34008235EN/AC - Page 17

5. Maintenance

Mounting the new battery module

Carry out the above instructions in reverse order.

5.3 Replacing the battery module in the rack model

Safety recommendations

The battery can cause electrocution and high short-circuit currents. The following safety precautions are required

before servicing the battery components:

◗ Remove watches, rings, bracelets and all other metal objects from the hands and arms,

◗ Use tools with an insulated handle.

Battery-module removal

◗ To ensure safety and high performance, use only batteries supplied by EATON.

◗ Take care to firmly press together the two parts of the connector during remounting.

A - Remove the two screws on the left-

hand side of the front panel.

B - Disconnect the battery block by

separating the two connectors (never pull

on the wires).

C - Remove the part.

B

C

34008235EN/AC - Page 18

5. Maintenance

Mounting the new battery module

Carry out the above instructions in reverse order.

5.4 Training centre

D - Pull the plastic tab to remove the

battery block and replace it.

◗ To ensure safety and high performance, use only batteries supplied by EATON.

◗ Take care to firmly press together the two parts of the connector during remounting.

To fully master operation of your EATON product and carry out level 1 servicing, see our complete range of technical

training courses, available in both French and English.

For further information, please visit our website: www.eaton.com

D

La pagina sta caricando ...

Eaton Evolution 1150 Rack Manuale utente

Eaton Evolution 1150 Rack Manuale utente

in altre lingue

Documenti correlati

Altri documenti