Simplicity CANADIANA DUAL STAGE SNOWTHROWER CE, HF 9.0TP 24" Manuale utente

Walkbehind Snowthrower

9.0 TP, 24 Inch (61,0 cm)

1750979

Revision -

Model No. 1695865

en

Operator’s Manual

cs

Bedienungsanleitung

de

Käyttäjän käsikirja

fi

Manuale dell’Operatore

fr

Brukerhåndbok

hu

Használati útmutató

it

Návod k obsluze

lt

Instrukcja obsługi

no

pl

Manuel d’utilisation

sl

Uporabniški priročnik

sv

Instruktionsbok

Vartotojo vadovas

Not for

Reproduction

2

Not for

Reproduction

2

3

5

3

1See Page 15.

4

A

B

C

DE

F

G

A

B

C

B

A

6

A

D

C

B

7

A

C

B

See Pages 17 and 18.

89

Not for

Reproduction

FULL

13

A

14

15

C

B

A

4

11

10

A

BC

D

12

A

B

A

Not for

Reproduction

5

16

17

18

A

B

A

19

A

20

21

A

C

A

B

Not for

Reproduction

.030 in.

(.76 mm)

26

27

B

A

28

Full

22

A

23

A

24

25

A

B

C

B

E

DA

C

B C

6

A

B

Not for

Reproduction

1/2” (12.5mm)

Deflection

83

7

29

A

30

1/8” (3mm)

Screw

A B

C

1/32”

(0.8mm)

31 D

E

A

C

B

F

32

33

B

A

C

Not for

Reproduction

8

Not for

Reproduction

9

CONTENTS

Illustrations ...........................................................................................3

Operator Safety......................................................................................10

Assembly.............................................................................................16

Features and Controls..............................................................................17

Operation.............................................................................................19

Maintenance.........................................................................................23

Storage ...............................................................................................28

Troubleshooting .....................................................................................29

Specifications .......................................................................................31

General Information

Thank you for purchasing this quality-built Murray snowthrower. We’re pleased that you’ve placed your confidence in the Murray brand.

When operated and maintained according to the instructions in this manual, your Murray product will provide many years of

dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with snowthrowers and how to avoid

them. This snowthrower is designed and intended only for snow throwing and is not intended for any other purpose. It is important that

you read and understand these instructions throughly before attempting to start or operate this equipment. Save these instructions for

future reference.

Record your model name/number, manufacturer’s identification

numbers, and engine serial numbers in the space provided for

easy access. These numbers can be found in the locations

shown.

When contacting your authorized dealer for replacement

parts, service, or information you MUST have these numbers.

A. Manufacturer’s Identification Number

B. Manufacturer’s Serial Number

C. Power Rating in Kilowatts

D. Maximum Engine Speed in Rotations per Minute

E. Manufacturer’s Name and Address

F. Year of Manufacture

G. CE Compliance Logo

H. Mass of Unit in Kilograms

I. Guaranteed Sound Power in Decibels

Part No. xxxxxxx

xxxxxxxxxxxxxxx

Serial No. xxxxxxxxxx

20xx

kW: x.xx

xxxx max

xxxxxxxxxxxxxxxxxxxxxxx

xxx dB

kg: xxx

A

B

C

D

E

FG

H

I

PRODUCT REFERENCE DATA

Model Description Name/Number

Unit MFG Number Unit SERIAL Number

Mower Deck MFG Number Mower Deck SERIAL Number

Dealer Name Date Purchased

ENGINE REFERENCE DATA

Engine Make Engine Model

Engine Type/Spec Engine Code/Serial Number

CE Identification Tag

Product Reference Data

The Illustrated Parts List for this machine can be downloaded from www.murray.com. Please provide model and serial number when

ordering replacement parts.

MURRAY is a trademark of Briggs & Stratton Power Products

Group, LLC Milwaukee, WI USA.

Not for

Reproduction

10

OPERATOR SAFETY

www.murray.com

Hazard Symbols and Meanings

Rotating

Impeller

Control Symbols on Equipment

12

Free-Hand™ Control

Easy-Turn™ Traction Control

NOTE: Not all control symbols shown on this page will

appear on your snowthrower. See Features and Controls

section for the applicable symbols.

STOP

Oil

Fuel

Shutoff

Choke

Off

Choke

On

On Off

Stop

Slow

Fast

Auger

Clutch

Electric

Start

Engine

Run

Engine

Stop

Traction

Control

Auger

Control

Discharge

Chute

Deflector

Heated

Hand

Grips

Rotating

Auger

Rotating

Parts

Fire

Shock

Hot

Surface

Safe

Distance

Rotating

Gears

Thrown

Objects

Explosion

Toxic

Fumes

Ear

Protection

Eye

Protection

Moving

Parts

Kickback

Hazardous

Chemical

Forward

Neutral

Reverse

Not for

Reproduction

OPERATOR SAFETY

11

The safety alert symbol and signal word (DANGER,

WARNING, CAUTION, or NOTICE) is used to indicate the likelihood

and potential severity of personal injury and/or damage to the

product. In addition, a hazard symbol may be used to represent the

type of hazard.

DANGER indicates a hazard which, if not avoided, will result

in death or serious injury.

WARNING indicates a hazard which, if not avoided, could

result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE indicates a situation that could result in damage

to the product.

DANGER

• Hand contact with the rotating impeller inside the discharge

chute is the most common cause of injury associated with

snowthrowers.

• This snowthrower is capable of amputating hands and feet,

and throwing objects. Read and observe all the safety

instructions in this manual. Failure to do so will result in

death or serious injury.

WARNING

Certain components in this product and its related accessories

contain chemicals known to the state of California to cause

cancer, birth defects, or other reproductive harm. Wash hands

after handling.

WARNING

The engine exhaust from this product contains chemicals

known to the State of California to cause cancer, birth defects,

or other reproductive harm.

• Be thoroughly familiar with the controls and the proper use of the

snow thrower.

• Make sure you are properly trained before operating the

snowthrower.

• Know how to stop the unit and disengage the controls quickly.

• Never allow anyone to operate the snowthrower without proper

instruction.

• Always follow the instructions in the operator’s manual, if the

snowthrower will be stored for an extende d period.

• Maintain or replace safety and instruction labels as necessary.

• Never attempt to make major repairs on the snowthrower unless

you have been properly trained. Improper servicing of the

snowthrower can result in hazardous operation, equipment

damage, and voiding of the product warranty.

DANGER

Read, understand, and follow all the

instructions on the snowthrower and in the

operator’s manual before operating this unit.

Failure to observe the safet y instructions in

this manual will result in death or serious

injury.

TO SAFELY CLEAR A CLOGGED DISCHARGE CHUTE

DANGER: Hand contact with the rotating impeller inside

the discharge chute is the most common cause of

injury associated with snow throwers. Never use your

hands to clean out the discharge chute.

FOLLOW THESE INSTRUCTIONS:

1. Shut OFF the engine.

2. Wait 10 seconds to be sure the impeller blades have stopped

rotating.

3. Always use a clean-out tool, not your hands.

DANGER

Discharge chute contains rotating impeller to

throw snow. Never clear or unclog the

discharge chute with your hands. Fingers can

quickly become caught in the impeller. Always

use a clean-out tool.

Failure to observe these safety instructions

will result in traumatic amputation or severe

laceration.

Discharge Chute

Not for

Reproduction

OPERATOR SAFETY

12

WHEN ADDING FUEL

• Turn off engine and let cool at least 3 minutes before removing

the fuel cap and adding fuel.

• Fill fuel tank outdoors or in a well ventilated area.

• Do not overfill the fuel tank. To allow for the expansion of gasoline,

do not fill above the bottom of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• Check fuel lines, cap, and fittings frequently for cracks or leaks.

Replace if necessary.

• Use an approved fuel container.

• If fuel spills, wait until it evaporates before starting engine.

WHEN STARTING ENGINE

• Ensure that spark plug, muffler, fuel cap, and air cleaner (if

equipped) are in place and secured.

• Do not crank the engine with the spark plug removed.

• If fuel is spilled, do not attempt to start the engine, but move the

snow thrower away from the area of the spill, and avoid creating

any source of ignition, until the fuel vapors have dissipated.

• Do not over-prime the engine. Follow the engine starting

instructions in this manual.

• If the engine floods, set choke (if equipped) to OPEN/RUN

position, move throttle (if equipped) to FAST position and crank

until engine starts.

WHEN OPERATING EQUIPMENT

• Do not tip the snowthrower at an angle which causes the fuel to

spill.

• Do not choke the carburetor to stop the engine.

• Never run the engine with the air cleaner assembly (if equipped)

or the air filter (if equipped) removed.

WHEN CHANGING OIL

• If you drain the oil from the top oil fill tube, the fuel tank must be

empty or fuel can leak out and result in a fire or explosion.

WHEN TRANSPORTING EQUIPMENT

• Transport with fuel tank EMPTY, or with fuel shut-off valve OFF.

WHEN STORING GASOLINE OR EQUIPMENT WITH FUEL

IN TANK

• Store away from furnaces, stoves, water heaters, or other

appliances that have pilot light or other ignition source because

they can ignite fuel vapors.

DANGER

Fuel and its vapors are extremely flammable

and explosive. Always handle fuel with extreme

care.

Failure to observe these safety instructions can

cause a fire or explosion which will result in

severe burns or death.

Fuel Handling

• Keep the area of operation clear of all persons, particularly small

children and pets.

• Thoroughly inspect the area where the snowthrower will be used

and remove all doormats, sleds, boards, wires, and other foreign

objects.

• Do not operate the snowthrower without wearing adequate winter

clothing.

• Wear footwear that will improve footing on slippery surfaces.

• Use caution to avoid slipping or falling especially when operating

the snowthrower in reverse.

• Never operate the snowthrower without good visibility or light.

Always be sure of your footing, and keep a firm hold on the

handles.

• Do not clear snow across the face of slopes. Use extreme caution

when changing direction on slopes. Do not attempt to clear steep

slopes.

• Do not overload the machine capacity by attempting to clear

snow too quickly.

• Never operate the snowthrower at high transport speeds on

slippery surfaces. Look behind the snowthrower and use care

when operating in reverse.

• Do not use the snowthrower on surfaces above ground level such

as roofs of residences, garages, porches, or other such structures

or buildings.

• Operators should evaluate their ability to operate the snowthrower

safely enough to protect themselves and others from injury.

• The snowthrower is intended to remove snow only. Do not use the

snow thrower for any other purpose.

• Do not carry passengers.

• After striking a foreign object, shut OFF the engine, disconnect

the cord on electric motors, thoroughly inspect the snowthrower

for any damage, and repair the damage before restarting and

operating the snowthrower.

• If the snowthrower vibrates abnormally, shut OFF the engine.

Vibration is generally a warning of trouble. See an authorized

dealer if necessary for repairs.

• For models equipped with electric starting motors, disconnect the

power cord after the engine starts.

DANGER

This snowthrower is only as safe as the

operator. If it is misused, or not properly

maintained, it can be dangerous. Remember

you are responsible for your safety and that of

those around you.

Operation and Equipment Safety

www.murray.com

Not for

Reproduction

OPERATOR SAFETY

13

• Keep children out of the area during operation. Children are often

attracted to the equipment. Be mindful of all persons present.

• Be alert and turn unit off if children enter the area.

• Never allow children to operate the unit.

• Use extra care when approaching blind corners, shrubs, trees, or

other objects that may obscure vision. Children may be present.

DANGER

Tragic accidents can occur if the operator is

not alert to the presence of children. Children

are often attracted to the unit and the

operating activity. Never assume that children

will remain where you last saw them.

Children

• Start and run engine outdoors.

• Do not run the engine in an enclosed area, even if doors or

windows are open.

DANGER

Engines give off carbon monoxide, an odorless,

colorless, poison gas.

Breathing carbon monoxide can cause nausea,

fainting, or death.

Engine Safety

• Disengage all clutches and shift into neutral before starting the

engine.

• Let the engine adjust to outdoor temperatures before starting to

clear snow.

• Use a grounded three-wire plug-in for all snowthrowers equipped

with electric drive motors or electric starting motors.

DANGER

Safe operation of the snowthrower requires the

proper care and maintenance of the engine.

Failure to observe the safety instructions in this

manual will result in death or serious injury.

• Always wear safety glasses or eye shields during operation, and

while performing an adjustment or repair.

• Always be aware of the direction the snow is being thrown.

Nearby pedestrians, pets, or property may be harmed by objects

being thrown.

• Be aware of your environment while operating the snowthrower.

Don’t run over items such as gravel, doormats, newspapers, toys,

and rocks hidden under snow, as they can all be thrown from the

chute or jam in the auger.

• Use extreme caution when operating on or crossing gravel drives,

walks, or roads.

• Adjust the collector housing height to clear gravel or crushed rock

surface.

• Never operate the snowthrower near glass enclosures,

automobiles, window wells, drop-offs, and the like without proper

adjustment of the discharge chute angle.

• Familiarize yourself with the area in which you plan to operate the

snow thrower. Mark off boundaries of walkways and driveways.

DANGER

Objects can be picked up by auger and thrown

from chute. Never discharge snow toward

bystanders or allow anyone in front of the

snowthrower. Failure to observe these safety

instructions will result in death or serious

injury.

Thrown Objects

• Whenever cleaning, repairing, or inspecting the snowthrower,

make sure the engine is OFF, spark plug wire is disconnected,

and all moving parts have stopped.

• Do not put hands or feet near or under rotating parts. Keep clear

of the discharge opening at all times.

• Never operate the snowthrower without proper guards, and other

safety devices in place and working.

• Never leave the snowthrower unattended while engine is running.

Always disengage the auger and traction controls, stop engine,

and remove keys.

• Keep all loose clothing away from the front of the snowthrower

and auger. Scarves, mittens, dangling drawstrings, loose clothes,

and pants can quickly become caught in the rotating device and

amputation will occur. Tie up long hair and remove jewelry.

• Run the machine a few minutes after discharging snow to prevent

freeze-up of the collector/impeller.

• Disengage power to the collector/impeller when snowthrower is

transported or not in use.

DANGER

Keep hands, feet, and clothing away from

rotating parts. Rotating parts can contact or

entangle hands, feet, hair, clothing, or

accessories.

Failure to observe these safety instructions will

result in traumatic amputation or severe

laceration.

Moving Parts

Not for

Reproduction

OPERATOR SAFETY

14

DANGER: READ OPERATOR’S

MANUAL.

Read the Operator’s Manual for

operating and safety instructions.

DANGER: THROWN OBJECTS

HAZARD.

Never direct discharge chute towards

persons or property. Keep bystanders

away.

DANGER: REMOVE KEY BEFORE

SERVICING.

Shut off engine and remove key before

performing maintenance or repair work.

DANGER: AMPUTATION HAZARD.

Contact with auger will cause serious

injury. Keep hands, feet, and clothing

away. Keep bystanders away.

DANGER: AMPUTATION HAZARD.

Contact with moving parts inside chute

will cause serious injury. Shut off engine

before unclogging discharge chute. Use

clean-out tool, not hands!

SAFETY ICONS

• When performing any maintenance or repairs on the

snowthrower, shut OFF the engine, disconnect spark plug wire,

and keep the wire away from the plug to prevent someone from

accidently starting the engine.

• Check shear bolts and other hardware at frequent intervals for

proper tightness to be sure the snowthrower is in safe working

condition.

• Keep nuts and bolts tight and keep snowthrower in good

condition.

• Never tamper with safety devices. Check their proper operation

regularly and make necessary repairs if they are not functioning

properly.

• Components are subject to wear, damage, and deterioration.

Frequently check components and replace with recommended

parts, when necessary.

• Check control operation frequently. Adjust and service as

required.

• Use only factory authorized replacement parts or like parts when

making repairs.

• Always comply with factory specifications on all settings and

adjustments.

• Only authorized service locations should be utilized for major

service and repair requirements.

• Use only attachments and accessories approved by the factory

(such as wheel weights, counterweights, or cabs).

• Never attempt to make any adjustments while the engine is

running (except when specifically recommended by the factory).

WARNING

This snowthrower must be properly maintained

to ensure safe operation and performance.

Failure to observe the safety instructions in this

manual could result in death or serious injury.

Maintenance and Storage

• If there is natural or LP gas leakage in area, do not start engine.

• Do not use pressurized starting fluids because vapors are

flammable.

WARNING

Starting engine creates sparking.

Sparking can ignite nearby flammable gases.

Explosion and fire could result.

• Never touch a hot engine or muffler. Allow muffler, engine

cylinder, and fins to cool before touching.

• Remove debris from muffler area and cylinder area.

• Install and maintain in working order a spark arrester before using

equipment on forest-covered, grass-covered, or brush-covered

unimproved land.

• It is a violation of California Public Resource Code, Section 4442,

to use or operate the engine on any forest-covered, brush-

covered, or grass-covered land unless the exhaust system is

equipped with a spark arrester, as defined in Section 4442,

maintained in effective working order. Other states or federal

jurisdictions may have similar laws. Contact the original

equipment manufacturer, retailer, or dealer to obtain a spark

arrester designed for the exhaust system installed on this engine.

WARNING

Running the engine produces heat. Engine

parts, especially muffler, become extremely hot.

Failure to observe these safety instructions

could result in severe thermal burns on contact.

Engine Safety (Continued)

www.murray.com

Not for

Reproduction

15

Safety Decals Figure 1

Look for this symbol to indicate important safety

precautions. This symbol indicates: “Attention!

Become Alert! Your Safety Is At Risk.”

WARNING: If any safety decals become worn or

damaged and cannot be read, order replacement decals

from your local dealer.

OPERATOR SAFETY

Before operating your snowthrower, read the safety decals as

shown on your snowthrower. The cautions and warnings are

for your safety. To avoid a personal injury or damage to your

snowthrower, understand and follow all the safety decals.

Part No. 1737871

Shift Decal

Part No. 1737869

Auger Control Decal

Part No. 1737870

Traction Control Decal

Part No. 1737867

Auger Control Icons

Part No. 1727207

Chute Control Icons

Product ID Number &

Serial Number Decal

(Rear of Motor Box)

Engine Warning Icons

Part No. 276925

Not for

Reproduction

16

CHECK THE TIRES

Check tires for damage. Check the air pressure in the tires with an

accurate gauge. See the sidewall of the tire for the proper inflation.

CAUTION: Avoid Injury! Explosive separation of tire

and rim parts is possible when they are serviced

incorrectly.

• Do not attempt to mount a tire without the proper

equipment and experience to perform the job.

• Do not inflate the tires above the recommended

pressure.

• Do not weld or heat a wheel and tire assembly. Heat can

cause an increase in air pressure resulting in an

explosion. Welding can structurally weaken or deform

the wheel.

• Do not stand in front or over the tire assembly when

inflating. Use appropriate tool that allows you to stand

to one side.

NOTICE: Check side of tire for maximum tire pressure. DO

NOT exceed maximum.

INSTALL THE DRIFT CUTTERS (If Equipped)

Drift cutters are used to cut a path through snow deeper than the auger

housing.

1. On each side of the auger housing, insert carriage bolt (A, Figure 7)

through upper hole.

2. Insert lower tab of drift cutter (B) into lower hole.

3. Secure with wing nuts (C).

ASSEMBLY

TOOLS REQUIRED FOR ASSEMBLY

1 – Knife

2 – 1/2" Wrenches (or adjustable wrenches)

1 – 7/16” Wrenches (or adjustable wrenches)

1 – Wrench (or adjustable wrench)

1 – Pair pliers or screw driver (to spread cotter pin)

1 – Hammer

1 – Pry Bar

CHECK CABLE CONNECTION AND ADJUSTMENT

The traction control cable (A, Figure 5) and auger control cable (B) are

adjusted at the factory and no adjustment should be necessary.

If the cables become stretched, unattached or begin to sag, adjustment

will be necessary. See MAINTENANCE section of this manual.

INSTALL THE DISCHARGE CHUTE

NOTE: The chute ring assembly (A, Figure 6) comes installed

on the unit from the factory.

1. Install discharge chute assembly (B) using four screws (C) and

nuts (D).

NOTE: Make sure the slot in the chute ring aligns with the

arrow on the outer ring as shown.

2. Tighten screws (C) snugly but be careful not to over-tighten.

WARNING: Always wear safety glasses or eye shields

when assembling the snowthrower.

UNPACK THE SNOWTHROWER

1. Using knife, cut along the dotted lines around the top of the carton.

Then remove top of carton as shown in Figure 2.

2. Using knife, cut along the dotted lines around the bottom of the

carton.

3. Push snowthrower off the bottom of the carton to proceed with

assembly.

PARTS BAG CONTENTS

1 – Shear Bolt Kit, 1/4-20 x 1-3/4 in.

1 – Bag of Shear Bolts

1 – Screw, 1/4-20 x 1-3/4 in.

1 – Spacer, Sleeve, 1/4 in.

1 – Hex Locknut, 1/4-20

1 – Grip, Lever, 1/2-13

NOTE: “Right” and “Left” are from the Operating Position.

ASSEMBLE THE HANDLES AND CHUTE CRANK

1. Loosen, but do not remove the bolts (A, Figure 3) flat washers (B),

lock washers (C) and hex nuts (D) in the upper holes of the lower

handle (E).

2. Remove the fasteners and the crank assembly eyebolt (F) from the

lower holes of the lower handle.

3. Raise upper handle (G) into operating position. Upper handle should

be to the outside of the lower handle.

NOTE: Make sure the cables are not caught between the upper

and lower handle.

4. Replace the fasteners and the crank assembly eyebolt. DO NOT

tighten until all fasteners are in place.

5. Attach the crank rod (A, Figure 4) to the universal joint assembly (B)

with the hair pin (C).

6. Replace and tighten nut on crank assembly eyebolt (F, Figure 3).

Make sure eye bolt is properly aligned and the crank can freely rotate.

7. Tighten all handle bolts.

NOTE: Make sure crank does not touch carburetor cover.

www.murray.com

Not for

Reproduction

17

FEATURES AND CONTROLS

SNOWTHROWER CONTROLS

A. Speed Select Lever — Allows the operator to use one of six (6)

forward and two (2) reverse speeds (see Figure 8). To shift, move

speed select lever to desired position.

NOTICE: Do not move speed select lever while Traction

Drive Clutch is engaged. This may result in severe damage

to drive system.

B. Auger Control Lever — Used to engage and disengage the auger

and impeller. To engage push down, to disengage release.

C. Chute Rotation Crank — Used to rotate the discharge chute to the

left or right.

D. Chute Deflector Wing Nut — Used to control the angle of the

chute deflector (up or down).

E. Traction Control Lever — Used to propel snowthrower forward or

reverse. Push down to engage, release to disengage.

F. Skid Shoe — Used to adjust ground clearance of auger housing.

G. Clean-Out Tool — Used to remove snow and debris from the

discharge chute and the auger housing.

Snowthrower Controls Figure 8

B

C

E

F

D

A

G

Not for

Reproduction

18

FEATURES AND CONTROLS

ENGINE CONTROLS

A. Choke Control Knob — Used to start a cold engine (see Figure 9).

B. Electric Start Button — Used to start the engine using the electric

starter.

C. Primer Button — Used to inject fuel directly into the carburetor

manifold to ensure fast starts in cool weather.

D. Safety Key — Must be inserted to start engine. Pull out to stop. Do

not turn safety key.

E. Starter Cord Handle — Used to start the engine manually.

F. ON/OFF Switch (if equipped) — Used to start and stop the

engine.

G. Fuel Tank and Cap — Fill the fuel tank to approximately 1-1/2 in.

(38 mm) below the top of the neck to allow for fuel expansion.

H. Oil Fill Cap (Extended Dipstick)

Engine Controls Figure 9

C

H

A

F

E

B

G

STOP

D

www.murray.com

Not for

Reproduction

OPERATION

STOP THE SNOWTHROWER

1. Release the auger control lever (B, Figure 10).

2. Release the traction control lever (C).

3. Push the ON/OFF switch (A, Figure 18), if equipped, to the OFF posi-

tion and pull out the safety key (B).

WARNING: Never run engine indoors or in an enclosed,

poor ventilated area. Engine exhaust contains CARBON

MONOXIDE, an ODORLESS and DEADLY GAS.

• Keep hands, feet, hair, and loose clothing away

from any moving parts on engine and

snowthrower.

• Temperature of muffler and nearby areas can

exceed 150°F (66°C). Avoid these areas.

• DO NOT allow children or young teenagers to

operate or be near snowthrower while it is

operating.

OPERATE THE SNOWTHROWER

CAUTION: Operation with a Snow Cab. Wind may blow

exhaust gasses back towards the operator. If you notice

the smell of exhaust, change direction of operation.

6. Use the speed select lever (D) to select the forward drive speed. Set

the speed select lever to one of the following positions as determined

by snow conditions:

1-2 Wet, Heavy, Slushy, Extra Deep

3 Moderate

4-5 Very Light

6 Transport

NOTE: When clearing wet, heavy, snow, it is recommended

that the ground speed of the unit be reduced, maintained full

throttle and do not attempt to clear the full width of the unit.

7. To stop moving forward, release the traction control lever (C).

8. To move the snowthrower backwards, move the speed select lever into

either first or second reverse position and engage the traction control

lever.

NOTE: Always release the traction control lever before moving

the speed select lever.

4. Fully press and hold the auger control lever (B, Figure 11) to engage

the auger rotation. Releasing the auger control lever will disengage

the auger.

5. Fully press and hold the traction control lever (C) to engage the

traction drive and begin moving the snowthrower. To disengage the

traction drive, completely release the lever.

CAUTION: Before operating, make sure the area in

front of the snowthrower is clear of bystanders or

obstacles.

NOTICE: Do not throw snow toward a building as hidden

objects could be thrown with sufficient force to cause damage.

1. Start the engine. See “To Start Engine” in this section.

2. Turn the chute rotation crank (A, Figure 10) to set the direction (left or

right) of the discharge chute.

3. Loosen the wing nut (A, Figure 11) on the side of the discharge chute

(B) to set angle (up or down) the snow is thrown.

19

BEFORE OPERATING SNOWTHROWER

Check the fasteners. Make sure all fasteners are tight.

On electric start models, the unit was shipped with the starter

cord plugged into the engine. Before operating, unplug the

starter cord from the engine.

NOTE: This snowthrower was shipped WITH OIL in the engine.

See Check the Oil (Before Starting Engine) instructions in this

section before starting engine.

Not for

Reproduction

OPERATION

WARNING: Read Operator’s Manual before operating

machine. This machine can be dangerous if used

carelessly.

• Never operate the snowthrower without all guards,

covers, shields in place.

• Never direct discharge towards windows or allow

bystanders near machine while engine is

running.

• Stop the engine whenever leaving the operating

position.

• Disconnect spark plug before unclogging the

impeller housing or the discharge chute and

before making repairs or adjustments.

• When leaving the machine, remove the safety key.

To reduce the risk of fire, keep the machine clean

and free from spilled gas, oil, and debris.

TRACTION LOCK PIN

The right traction wheel can be completely released using the locking pin

(A, Figure 12). This allows the unit to be easily moved with the engine off.

CHECK THE OIL (BEFORE STARTING ENGINE)

NOTE: The engine was shipped from the factory filled with oil.

Check the level of the oil. Add oil as needed.

1. Make sure the unit is level. Use a high quality detergent oil classified

“For Service SF, SH, SJ, SL, or higher”.

2. Remove the oil fill cap/dipstick (A, Figure 13) and wipe with a clean cloth.

3. Insert the oil fill cap/dipstick and turn clockwise to tighten.

4. Remove the oil fill cap/dipstick and check the oil.

NOTE: Do not check the level of the oil while the engine runs.

5. If necessary, add oil until the oil reaches the FULL mark on the oil fill

cap/dipstick. Do not add too much oil.

6. Tighten the oil fill cap/dipstick securely each time you check the oil

level.

NOTE: Synthetic 5W30 motor oil is acceptable for all

temperatures. DO NOT mix oil with gasoline. See Chart for oil

recommendations.

* Below 40°F (4°C) the use of SAE 30 will result in hard starting.

** Above 80°F (27°C) the use of 10W-30 may cause increased oil consumption. Check oil

level more frequently.

20 www.murray.com

Not for

Reproduction

La pagina sta caricando ...

Simplicity CANADIANA DUAL STAGE SNOWTHROWER CE, HF 9.0TP 24" Manuale utente

Simplicity CANADIANA DUAL STAGE SNOWTHROWER CE, HF 9.0TP 24" Manuale utente

in altre lingue

Documenti correlati

Altri documenti