Rosemount Oxymitter 4000 O2 Transmitter-Rev 4.3 Manuale del proprietario

Instruction Manual

IM-106-340, Rev 4.3

July 2017

Rosemount

TM

Oxymitter 4000

Oxygen Transmitter

HIGHLIGHTS OF CHANGES

Effective May 31, 2006 Rev. 4.0

Page Summary

General Reformatted entire manual from a two column layout. Removed all references to JIS

specifications. Replaced SPS 4000 information with SPS 4001B information.

Cover Updated photo, revision number and date.

viii Removed Figure 3. Oxymitter 4000 with SPS 4000 Wiring Diagram from Quick Start

Guide.

1-2 Revised Figure 1-1 to show SPS 4001B and updated IMPS 4000.

1-5 Revised Figure 1-2 to show SPS 4001B.

1-8 Added step 11 and Figure 1-6.

1-10, 1-11 Revised Figure 1-8 and Figure 1-9 to show SPS 4001B.

1-12 Removed Components paragraph.

1-13 Removed Figure 1-9. SPS 4000.

1-15

Updated Figure 1-14. Abrasive Shield Assembly.

1-16

, 1-17 Revised Specifications.

1-18, 1-19 Revised Product Matrix table.

2-1 Added two additional warnings.

2-5 Removed Figure 2-3. Oxymitter 4000 Installation (with SPS 4000).

2-12, 2-15 Revised Figure 2-9 and Figure 2-10 to show grounding locations.

2-16 Revised Install Interconnecting Cable paragraph. Removed Electrical Installation (For

Oxymitter 4000 with SPS 400).

2-18 Added SPS 4001B Connections.

3-1, 4-1 Revised Terminal Block Wiring text.

5-2 Added Reference Air information.

7-9 Added D/A Trim Procedure.

8-3 Revised Alarm Indications to include signal alarm levels.

8-23 Removed SPS 4000 Troubleshooting.

9-8, 9-9 Revised Figure 9-3 and Figure 9-4.

9-11, 9-13 Revised Figure 9-6 and Figure 9-7 with updated circuit board.

9-17 Revised Figure 9-10.

9-20 Removed SPS 4000 Maintenance and Component Replacement.

10-3

, 10-4 Updated part numbers for the Cell Replacement Kit, ANSI 15’ and 18’.

10-4

Updated part numbers for the Contact and Thermocouple Replacement Assembly, 15’ and

18’.

HIGHLIGHTS OF CHANGES (CONTINUED)

Effective May 31, 2006 Rev. 4.0 (Continued)

Page Summary

10-5

Removed Ceramic Diffuser Hub Assy. Changed part numbers 4851B89G04 and

4851B90G04 to 10 microns.

10-6

Revised Table 10-2. Removed Replacement Parts for SPS 4000 table.

11-4 Revised Figure 11-4 to show the SPS 4001B.

11-6

Added Figure 11-7 and explanation of the Oxybalance Display and Averaging System.

A-21 Added General Precautions for Handling and Storing High Pressure Gas Cylinders.

Effective January 2007 Rev. 4.1

Page Summary

General Revised reference air specifications to read 1 l/min (2 scfh) throughout the manual.

Page 8-22 Added the paragraph and procedural steps after 'Heater Not Open, but Unable to Reach

736°C Setpoint. '

Page A-2 thru A-24 Added note 11 to the safety data section. Added new language translations.

Page B-1 Updated the return of materials address.

Back cover Updated the address blocks.

Effective July 2008 Rev. 4.2

Page Summary

Page 6-4 Added note regarding cleaning the LOI screen before use.

Effective July 2017 Rev. 4.3

Page Summary

Title page Added “Rosemount” to manual title.

Replaced Emerson Process Management logo with Emerson logo.

General Replaced all instances of “Rosemount Analytical” with “Rosemount”.

Replaced all instances of “Emerson Process Management” with “Emerson”.

Back cover Added URL to main website.

Added social media icons and URLs.

Updated address blocks.

Replaced Rosemount Analytical and Emerson Process Management logos with

Rosemount and Emerson logos.

Instruction Manual

IM-106-340, Rev 4.3

July 2017

Oxymitter 4000

TOC-1

Table of Contents

Essential Instructions .................................................................................i

SECTION i

Introduction

Preface .................................................................................................... iv

Definitions ................................................................................................ iv

Symbols ................................................................................................... iv

What You Need To Know ........................................................................ v

Can You Use the Quick Start Guide? ..................................................... vii

Quick Start Guide for Oxymitter 4000 Systems ..................................... viii

Quick Reference Guide Manual Calibration Instructions ........................ ix

HART Communicator Fast Key Sequences ............................................ x

SECTION 1

Description and

Specifications

Component Checklist ........................................................................... 1-1

System Overview .................................................................................. 1-1

Scope .............................................................................................. 1-1

System Description ......................................................................... 1-3

System Configuration ...................................................................... 1-4

System Features ............................................................................. 1-4

Handling the Oxymitter 4000 ........................................................... 1-8

System Considerations ................................................................... 1-9

IMPS 4000 (Optional) ......................................................................... 1-12

SPS 4001B (Optional) ........................................................................ 1-12

Mounting ........................................................................................ 1-12

Operation ....................................................................................... 1-12

Model 751 Remote Powered Loop LCD Display ................................ 1-13

Probe Options ..................................................................................... 1-13

Diffusion Elements ........................................................................ 1-13

Specifications ..................................................................................... 1-16

SECTION 2

Configuration of

Oxymitter 4000

with Membrane

Keypad

Verify Installation .................................................................................. 2-1

Mechanical Installation .................................................................... 2-1

Terminal Block Wiring ..................................................................... 2-1

Oxymitter 4000 Configuration ......................................................... 2-2

Logic I/O ............................................................................................... 2-5

Recommended Configuration ......................................................... 2-6

SECTION 3

Installation

Mechanical Installation ......................................................................... 3-2

Selecting Location ........................................................................... 3-2

Probe Installation ............................................................................. 3-2

Remote Electronics Installation ....................................................... 3-9

Electrical Installation (with Integral Electronics) ................................. 3-10

Electrical Installation (with Remote Electronics)................................. 3-13

Install Interconnecting Cable ......................................................... 3-16

Pneumatic Installation ........................................................................ 3-16

IMPS 4000 Connections ..................................................................... 3-18

SPS 4001B Connections .................................................................... 3-18

Instruction Manual

IM-106-340, Rev 4.3

July 2017

Oxymitter 4000

TOC-2

SECTION 4

Configuration of

Oxymitter 4000 with LOI

Verify installation ................................................................................... 4-1

Mechanical Installation .................................................................... 4-1

Terminal Block Wiring ...................................................................... 4-1

Oxymitter 4000 Configuration .......................................................... 4-2

Logic I/O ................................................................................................ 4-4

Recommended Configuration .......................................................... 4-6

SECTION 5

Startup and Operation of

Oxymitter 4000 with

Membrane Keypad

Power Up .............................................................................................. 5-1

Operation .............................................................................................. 5-2

Overview .......................................................................................... 5-2

SECTION 6

Startup and Operation of

Oxymitter 4000 with LOI

Power Up .............................................................................................. 6-1

Start Up Oxymitter 4000 Calibration ..................................................... 6-3

Navigating the Local Operator Interface ............................................... 6-3

Overview .......................................................................................... 6-3

Lockout ............................................................................................ 6-3

LOI Key Designations ........................................................................... 6-4

LOI Menu Tree ...................................................................................... 6-4

Oxymitter 4000 Setup at the LOI .......................................................... 6-6

LOI Installation ...................................................................................... 6-9

Oxymitter 4000 Test Points ................................................................. 6-10

Remote Powered Loop LCD Display (Optional) ................................. 6-10

SECTION 7

HART/AMS

Overview ............................................................................................... 7-1

HART Communicator Signal Line Connections .................................... 7-2

HART Communicator PC Connections ................................................. 7-2

Off-Line and On-Line Operations .......................................................... 7-4

Logic I/O Configurations ....................................................................... 7-4

HART/AMS Menu Tree ......................................................................... 7-4

HART Communicator O

2

Cal Method ................................................... 7-8

Defining a Timed Calibration via HART ................................................ 7-9

D/A Trim Procedure .............................................................................. 7-9

SECTION 8

Troubleshooting

Overview ............................................................................................... 8-1

General ................................................................................................. 8-3

Alarm Indications................................................................................... 8-3

Alarm Contacts...................................................................................... 8-4

Identifying and Correcting Alarm Indications ........................................ 8-5

Heater Not Open, but Unable to Reach 736°C Setpoint ..................... 8-22

Calibration Passes, but Still Reads Incorrectly ................................... 8-22

SECTION 9

Maintenance and Service

Overview ............................................................................................... 9-1

Calibration with Keypad ........................................................................ 9-1

Automatic Calibration ....................................................................... 9-2

Semi-Automatic Calibration ............................................................. 9-3

Manual Calibration with Membrane Keypad .................................... 9-3

Calibration with LOI ............................................................................... 9-5

Oxymitter 4000 Repair .......................................................................... 9-7

Removal and Replacement of Probe ............................................... 9-7

Instruction Manual

IM-106-340, Rev 4.3

July 2017

Oxymitter 4000

TOC-3

SECTION 10

Replacement Parts

Probe Replacement Parts .................................................................. 10-1

Electronics Replacement Parts .......................................................... 10-6

SECTION 11

Optional

Accessories

HART Handheld 375 Communicator .................................................. 11-1

Asset Management Solutions (AMS) ................................................. 11-2

By-Pass Packages ............................................................................. 11-2

IMPS 4000 Intelligent Multiprobe Test Gas Sequencer ..................... 11-3

SPS 4001B Single Probe Autocalibration Sequencer ........................ 11-4

O

2

Calibration Gas ............................................................................. 11-5

Catalyst Regeneration ........................................................................ 11-6

OxyBalance Display and Averaging System ...................................... 11-6

APPENDIX A

Safety Data

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

Safety Data Sheet for Ceramic Fiber Products . . . . . . . . . . . . . . . . A-24

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-30

APPENDIX B

Return of Material

Returning Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

Instruction Manual

IM-106-340, Rev 4.3

July 2017

Oxymitter 4000

TOC-4

Instruction Manual

IM-106-340, Rev. 4.3

July 2017

Oxymitter 4000

ESSENTIAL

INSTRUCTIONS

Oxymitter Oxygen Transmitters

READ THIS PAGE BEFORE PROCEEDING!

Emerson designs, manufactures and tests its products to meet many national

and international standards. Because these instruments are sophisticated

technical products, you MUST properly install, use, and maintain them to

ensure they continue to operate within their normal specifications. The

following instructions MUST be adhered to and integrated into your safety

program when installing, using, and maintaining Emerson’s Rosemount

products. Failure to follow the proper instructions may cause any one of the

following situations to occur: Loss of life; personal injury; property damage;

damage to this instrument; and warranty invalidation.

•

Read all instructions prior to installing, operating, and servicing the

product.

•

If you do not understand any of the instructions, contact your

Emerson representative for clarification.

•

Follow all warnings, cautions, and instructions marked on and

supplied with the product.

•

Inform and educate your personnel in the proper installation,

operation, and maintenance of the product.

•

Install your equipment as specified in the Installation Instructions

of the appropriate Instruction Manual and per applicable local and

national codes. Connect all products to the proper electrical and

pressure sources.

•

To ensure proper performance, use qualified personnel to install,

operate, update, program, and maintain the product.

•

When replacement parts are required, ensure that qualified people use

replacement parts specified by Emerson. Unauthorized parts and

procedures can affect the product's performance, place the safe

operation of your process at risk, and VOID YOUR WARRANTY.

Look-alike substitutions may result in fire, electrical hazards, or

improper operation.

•

Ensure that all equipment doors are closed and protective covers

are in place, except when maintenance is being performed by

qualified persons, to prevent electrical shock and personal injury.

The information contained in this document is subject to change without

notice.

If a Model 275/375 Universal HART® Communicator is used with this unit, the software

within the Model 275/375 may require modification. If a software modification is required,

please contact your local Emerson Service Group or National Response Center at 1-800-

433-6076 or 1-888-433-6829.

Instruction Manual

IM-106-340, Rev. 4.3

July 2017

Oxymitter 4000

iv

Instruction Manual

IM-106-340, Rev. 4.3

July 2017

Oxymitter 4000

Section i Introduction

Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page iv

Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page iv

Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page iv

What You Need To Know . . . . . . . . . . . . . . . . . . . . . . . . . . page v

Can You Use the Quick Start Guide? . . . . . . . . . . . . . . . . page vii

Quick Start Guide for Oxymitter 4000 Systems . . . . . . . . page viii

Quick Reference Guide Manual Calibration Instructions page ix

HART Communicator Fast Key Sequences . . . . . . . . . . . page x

Instruction Manual

IM-106-340, Rev. 4.3

July 2017

Oxymitter 4000

iv

PREFACE The purpose of this manual is to provide information concerning the

components, functions, installation and maintenance of the Oxymitter 4000

Oxygen Transmitter.

Some sections may describe equipment not used in your configuration. The

user should become thoroughly familiar with the operation of this module

before operating it. Read this instruction manual completely.

DEFINITIONS The following definitions apply to WARNINGS, CAUTIONS, and NOTES

found throughout this publication.

SYMBOLS

NOTE

Highlights an essential operating procedure, condition, or statement.

:

EARTH (GROUND) TERMINAL

:

PROTECTIVE CONDUCT OR TERMINAL

:

RISK OF ELECTRICAL SHOCK

:

WARNING: REFER TO INSTRUCTION MANUAL

NOTE TO USERS

The number in the lower right corner of each illustration in this publication is a

manual illustration number. It is not a part number, and is not related to the

illustration in any technical manner.

Highlights an operation or maintenance procedure, practice, condition, statement, etc. If not

strictly observed, could result in injury, death, or long-term health hazards of personnel.

Highlights an operation or maintenance procedure, practice, condition, statement, etc. If not

strictly observed, could result in damage to or destruction of equipment, or loss of

effectiveness.

Instruction Manual

IM-106-340, Rev. 4.3

July 2017

Oxymitter 4000

v

IMPS

4000

SPS

4001B

WHAT YOU NEED TO

KNOW

BEFORE INSTALLING AND WIRING A ROSEMOUNT OXYMITTER 4000

OXYGEN TRANSMITTER

1. What type of installation does your system require?

Use the following drawings, Figure 1 and Figure 2, to identify which type

of installation is required for your Oxymitter 4000 system.

Figure 1. Installation Options -

Oxymitter 4000 with Integral

Electronics

OXYMITTER 4000

Line Voltage

4-20 mA

Cal. Gas

Instr. Air (Ref. Air)

OXYMITTER 4000 WITH

SPS 4001B

Line Voltage

4-20 mA

LOGIC I/O

Cal. Gas

Ref. Air

Line Voltage

Cal. Gas 1

Cal. Gas 2

Instr. Air (Ref. Air)

OXYMITTER 4000 WITH REMOTE

IMPS 4000 OPTION

Line Voltage

4-20 mA

LOGIC I/O

Cal. Gas

Ref. Air

Line Voltage

Cal. Gas 1

Cal. Gas 2

Instr. Air (Ref. Air)

Highlights an operation or maintenance procedure, practice, condition, statement, etc. If not

strictly observed, could result in injury, death, or long-term health hazards of personnel.

38890001

Instruction Manual

IM-106-340, Rev. 4.3

July 2017

Oxymitter 4000

vi

Figure 2. Installation Options -

Oxymitter 4000 with Remote

Electronics

OXYMITTER 4000

Line Voltage

4-20 mA

Cal. Gas

Instr. Air (Ref. Air)

OXYMITTER 4000 WITH

REMOTE ELECTRONICS

AND SPS 4001B

Line Voltage

4-20 mA

Logic I/O

Calibration Gas

Reference Air

Cal. Gas 2

Cal. Gas 1

Instr. Air

SPS

4001B

OXYMITTER 4000 WITH

REMOTE ELECTRONICS

AND IMPS

Line Voltage

4-20 mA

Logic I/O

Calibration Gas

Reference Air

Cal. Gas 2

Cal. Gas 1

Instr. Air

IMPS

4000

38890049

Instruction Manual

IM-106-340, Rev. 4.3

July 2017

Oxymitter 4000

vii

CAN YOU USE THE

QUICK START GUIDE?

Use this Quick Start Guide if...

1.

Your system requires an Oxymitter 4000 with or without the SPS 4001B

OPTION. Installation options for the Oxymitter 4000 are shown in

Figure 1.

2.

Your system does NOT require an IMPS 4000 OPTION installation.

3.

Your system does NOT use a Remote Electronics as shown in Figure 2.

4.

You are familiar with the installation requirements for the Oxymitter 4000

Oxygen Transmitter. You are familiar with the installation requirements

for the Oxymitter 4000 Oxygen Transmitter with a SPS 4001B.

If you cannot use the Quick Start Guide, turn to Section 3: Installation, in

this Instruction Manual.

Instruction Manual

IM-106-340, Rev. 4.3

July 2017

Oxymitter 4000

viii

QUICK START GUIDE

FOR OXYMITTER 4000

SYSTEMS

Before using the Quick Start Guide, please read "WHAT YOU NEED TO

KNOW BEFORE INSTALLING AND WIRING A ROSEMOUNT

OXYMITTER 4000 OXYGEN TRANSMITTER" on the

preceding page.

1.

Install the Oxymitter 4000 in an appropriate location on the stack or

duct. Refer to "Selecting Location" in Section 3: Installation, for

information on selecting a location for the Oxymitter 4000.

2.

If using an SPS 4001B, connect the calibration gasses to the

appropriate fittings on the SPS 4001B manifold.

3.

Connect reference air to the Oxymitter 4000 or SPS 4001B, as

applicable.

4.

If using an SPS 4001B, make the wiring connections as shown in the

SPS 4001B Single Probe Autocalibration Sequencer Instruction

Manual.

5.

If NOT using an SPS 4001B, make the following wire connections as

shown in Figure 3: line voltage, 4-20 mA, and logic I/O.

6.

Verify the Oxymitter 4000 switch configuration is as desired. Refer to

"Oxymitter 4000 Configuration", "SW1 Setting", and "SW2 Setting" all in

Section 2: Configuration of Oxymitter 4000 with Membrane Keypad, or

"Oxymitter 4000 Configuration", "SW1 Setting", and "SW2 Setting" all in

Section 4: Configuration of Oxymitter 4000 with LOI.

7.

Apply power to the Oxymitter 4000; the cell heater will turn on. Allow

approximately one half hour for the cell to heat to operating

temperature. Once the ramp cycle has completed and the

Oxymitter 4000 is at normal operation, proceed with step 8 or 9.

8.

If using an SPS 4001B, initiate a semi-automatic calibration.

9.

If NOT using an SPS 4001B, perform a manual calibration. Refer to

"Calibration with Keypad" or "Calibration with LOI" both in Section 9:

Maintenance and Service, in this instruction manual.

NOTE

If your system has a membrane keypad you can refer to the Quick Start Guide

on the following pages.

Instruction Manual

IM-106-340, Rev. 4.3

July 2017

Oxymitter 4000

ix

Figure 3. Oxymitter 4000 without SPS 4001B Wiring Diagram

QUICK REFERENCE

GUIDE MANUAL

CALIBRATION

INSTRUCTIONS

Performing a Manual Calibration with a Membrane Keypad

1.

Place the control loop in manual.

2.

Press the CAL key. The CAL LED will light solid.

3.

Apply the first calibration gas.

4.

Press the CAL key. When the unit has taken the readings using the first

calibration gas, the CAL LED will flash continuously.

5.

Remove the first calibration gas and apply the second calibration gas.

6.

Push the CAL key. The CAL LED will light solid. When the unit has

taken the readings using the second calibration gas, the CAL LED will

flash a two-pattern flash or a three-pattern flash. A two-pattern flash

equals a valid calibration, three-pattern flash equals an invalid

calibration.

7.

Remove the second calibration gas and cap off the calibration gas port.

8.

Press the CAL key. The CAL LED will be lit solid as the unit purges.

When the purge is complete, the CAL LED will turn off.

9.

If the calibration was valid, the DIAGNOSTIC ALARMS LEDs indicate

normal operation. If the new calibration values are not within the

parameters, the DIAGNOSTIC ALARMS LEDs will indicate an alarm.

10.

Place the control loop in automatic.

Instruction Manual

IM-106-340, Rev. 4.3

July 2017

Oxymitter 4000

x

HART COMMUNICATOR

FAST KEY SEQUENCES

Perform Calibration

2

3

1

Trim Analog Output

Toggle Analog Output Tracking

O

2

Upper Range Value

3

2

1

Analog Output Lower Range Value

3

2

View O

2

Value

View Analog Output

1

2

1

Technical Support Hotline:

For assistance with technical problems, please call the Customer Support

Center (CSC). The CSC is staffed 24 hours a day, 7 days a week.

Phone: 1-800-433-6076 1-440-914-1261

In addition to the CSC, you may also contact Field Watch. Field Watch

coordinates Emerson’s field service throughout the

U.S. and abroad.

Phone: 1-800-654-RSMT (1-800-654-7768)

Emerson may also be reached via the Internet through e-mail and the World

Wide Web:

e-mail: GAS.CSC@emersonprocess.com

World Wide Web: www.raihome.com

2

3

1

2

1

38890060

Instruction Manual

IM-106-340, Rev. 4.3

July 2017

Oxymitter 4000

Section 1 Description and Specifications

Component Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1-1

System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1-1

IMPS 4000 (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1-12

SPS 4001B (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1-12

Model 751 Remote Powered Loop LCD Display . . . . . . . page 1-13

Probe Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1-13

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1-16

COMPONENT

CHECKLIST

A typical Rosemount Oxymitter 4000 Oxygen Transmitter should contain the

items shown in Figure 1-1. Record the part number, serial number, and order

number for each component of your system in the table located on the first

page of this manual.

Also, use the product matrix in Table 1-1 at the end of this section to compare

your order number against your unit. The first part of the matrix defines the

model. The last part defines the various options and features of the Oxymitter

4000. Ensure the features and options specified by your order number are on

or included with the unit.

SYSTEM OVERVIEW

Scope This Instruction Manual is designed to supply details needed to install, start

up, operate, and maintain the Oxymitter 4000. Signal conditioning electronics

outputs a 4-20 mA signal representing an O

2

value and provides a membrane

keypad or fully functional Local Operator Interface (optional) for setup,

calibration, and diagnostics. This same information, plus additional details,

can be accessed with the HART Model 275/375 handheld communicator or

Asset Management Solutions (AMS) software.

Instruction Manual

IM-106-340, Rev. 4.3

July 2017

Oxymitter 4000

1-2

Figure 1-1. Typical System

Package

1.

Instruction Manual

2.

IMPS 4000 Intelligent Multiprobe Test Gas Sequencer (Optional)

3.

Oxymitter 4000 with Integral Electronics

4.

SPS 4001B Single Probe Autocalibration Sequencer (Optional) (Shown with reference air option)

5.

HART® 275/375 Communicator Package (Optional)

6.

Adapter Plate with Mounting Hardware and Gasket

7.

Remote Electronics and Cable (Optional)

8.

Reference Air Set (used if SPS 4001B without reference air option or IMPS 4000 supplied)

La pagina sta caricando ...

Rosemount Oxymitter 4000 O2 Transmitter-Rev 4.3 Manuale del proprietario

Rosemount Oxymitter 4000 O2 Transmitter-Rev 4.3 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti