ProLights ARCPOD48Q Manuale utente

USER MANUAL

MANUALE UTENTE

ARCPOD48Q

OUTDOOR COMPACT WASHLIGHT

EN - IT

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the characteris-

tics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

REV. 01-04/19

1

ARCPOD48Q

Packing content

• ARCPOD48Q

• Power adaptor cable

• Signal adaptor cable (2 pcs)

• User manual

TABLE OF CONTENTS

Safety

General instructions

Warnings and installation precautions

1 Introduction

1. 1 Description

1. 2 Technical specications

1. 3 Operating elements and connections

2 Installation

2. 1 Mounting

3 Functions and settings

3. 1 Operation

3. 2 Basic

3. 3 RDM mode

3. 4 RDM function

3. 5 Linking

3. 6 DMX addressing conguration

3. 7 DMX mode conguration

3. 8 DMX addressing

3. 9 Dimmer mode

3. 10 LED frequency

3. 11 Sensor menu

3. 12 Sw version

3. 13 UID

3. 14 Factory Default

3. 15 Manual color

3. 16 Full on mode

3. 17 Connection of the DMX line

3. 18 Construction of the DMX termination

3. 19 DMX control

4 Maintenance

4. 1 Maintenance and cleaning the unit

4. 2 Trouble shooting

2

3

5

6

7

8

9

10

11

12

13

16

ARCPOD48Q

2

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

SAFETY

General instruction

• The products referred to in this manual conform to the European Community Directives and are there-

fore marked with .

• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.

Never make any modications on the unit not described in this instruction manual, otherwise you will

risk an electric shock.

• Connection must be made to a power supply system tted with ecient earthing (Class I appliance ac-

cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units

from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• The connection to the main network of electric distribution must be carried out by a qualied electrical

installer. Check that the main frequency and voltage correspond to those for which the unit is designed

as given on the electrical data label.

• This unit is not for home use, only professional applications.

• Never use the xture under the following conditions:

- in places subject to vibrations or bumps;

- in places with an ambient temperature of over 50°C.

• Make certain that no inammable liquids, water or metal objects enter the xture.

• Do not dismantle or modify the xture.

• All work must always be carried out by qualied technical personnel. Contact the nearest sales point for

an inspection or contact the manufacturer directly.

• If the unit is to be put out of operation denitively, take it to a local recycling

plant for a disposal which is not harmful to the environment.

Warnings and installation precautions

• If this device will be operated in any way dierent to the one described in this manual, it may suer

damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like

short circuit, burns, electric shock, etc.

• Before starting any maintenance work or cleaning the projector, cut o power from the main supply.

• When carrying out any work, always comply scrupulously with all the regulations (particularly regard-

ing safety) currently in force in the country in which the xture’s being used.

• The minimum distance between the xture and surrounding walls must be more than 50 cm and the

air vents at the housing must not be covered in any case.

• Keep any inammable material at a safe distance from the xture.

• The maximum temperature that can be reached on the external surface of the tting, in a thermally

steady state, is high. After power o, please cool down over 15 minutes.

• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent

that their eectiveness is impaired.

• The lamp (LED) shall be changed if it has become damaged or thermally deformed.

• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ashing light, may

trigger epileptic seizures in photosensitive persons or persons with epilepsy.

• This product was designed and built strictly for the use indicated in this documentation. Any other use,

not expressly indicated here, could compromise the good condition/operation of the product and/or

be a source of danger.

• We decline any liability deriving from improper use of the product.

3

ARCPOD48Q

- 1 - INTRODUCTION

1.1 DESCRIPTION

ARCPOD48Q is a compact high-power outdoor wash light featuring an outstanding brightness of 28208

lumens. Equipped with 48 x 10W RGBW full-colour LEDs, delivering superior colour mixing. The slim siz-

ing, as well as the wide range of available optics through the magnet, makes the ARCPOD48Q an incred-

ibly exible and versatile device for large outdoor applications.

1.2 TECHNICAL SPECIFICATIONS

LIGHT SOURCE

• Source: 48X10W RGBW/FC LEDs

• Luminous ux: 28208lm

• Lux: (15°) 26200lux @3m full

• Lux: (15°) 9432lux @5m full

• Source life expectancy: >50.000 h

OPTICS

• Beam angle: 15°

• Field angle: 27°

• Additional optics: 10°, 25°, 45°

• Other: barn doors not included

COLOUR SYSTEM

• Colour mixing: RGBW/FC

• CTC: CTC control through independent DMX channel

• Colour wheel: virtual colour wheel with presets

• Macros: several pre-build macros with adjustable speed

DYNAMIC EFFECTS

• FX generator: section eect with 4 horizontal individually select and control sections

• Static colour mode: selection of static colour

• Manual colour mode: manual adjustment of colour

• Auto mode: built-in programs with execution speed adjustment

BODY

• Tilt angle: 0-130° manual

• Body: sturdy die-cast aluminium body conceived for long-time durability

• Body colour: grey

CONTROL

• Protocols: DMX512, RDM

• DMX channels: 5 / 7 / 10 / 17 / 22channel

• RDM: RDM ready for xture remote monitor and settings

• Display: user interface through DATAMASTER external coder (not included)

• Firmware upgrade: yes, via USB-DMX interface (UPBOX1) not included

• Master/Slave: for synchronized operation of more units linked in a chain

ARCPOD48Q

4

ELECTRONICS

• Dimmer: linear 0~100% electronic dimmer

• Dimmer curves: 4 dierent dimming curves available

• Strobe / shutter: 1 - 30 Hz, electronic

• Operating temperature: -20° ~ +50°

• Flicker: icker free operation

• Selectable PWM: 600~25K Hz

ELECTRICAL

• Power consumption: 700

• Power supply: 100-240V – 50/60Hz

• Power consumption (at 230V): 521W

• Power consumption (at 120V): 552W

• Output (at 230V): 4 units on a single power line

• Output (at 120V): 2 units on a single power line

• Power factor: 0.95

PHYSICAL

• Cooling: natural cooling of the peculiar chassis and to absence of fans

• Adaptors: XLR and Shuko 16A adaptors included

• Signal connection: moulded IP signal IN/OUT connectors

• Power connection: moulded IP power IN/OUT connectors

• IP rating: 66 for outdoor installations

• Dimensions (WxHxD): 574x304x114 mm

• Weight: 14kg

304

574

114

Technical drawing Fig.1

5

ARCPOD48Q

1.3 OPERATING ELEMENTS AND CONNECTIONS

1. LED panel

2. MECHANICAL SYSTEM for individual position-

ing of Led panels

3. HOLES for xing to the ground

4. POWER IN: for connection to a socket

(100-240V~/50-60Hz) via the supplied mains

cable

Fig.2

5. DMX IN (5-pole XLR): 1 = ground, 2 = DMX-, 3 =

DMX+, 4 N/C, 5 N/C.

6. HEATSINK

7. DMX OUT (5-pole XLR): 1 = ground, 2 = DMX-, 3 =

DMX+, 4 N/C, 5 N/C.

8. POWER OUT: connect to supply power to the next

unit.

1

2

3

4

5

6

7 8

ARCPOD48Q

6

- 2 - INSTALLATION

2.1 MOUNTING

The ARCPOD48Q may be set up on a solid and even surface using the fastening devices of the base (2).

Stable mounting clips are required for xing.

Also make sure to comply with all safety warnings.

Fig.3

1

2

7

ARCPOD48Q

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

Connect the supplied main cable to a socket (100-240V~/50-60Hz). To switch o, disconnect the mains

plug from the socket. For a more convenient operation it is recommended to connect the unit to a socket

which can be switched on and o via light switch.

3.2 BASIC

To control the ARCPOD48Q connect the device to a DATAMASTER (g.4).

DATAMASTER is a powerful RDM-DMX tool that automatically detects connected RDM devices, allowing

direct and fast monitoring and control. Information on the status of the connected xture can be read

from the DATAMASTER display.

DMX OUT

Fig.4

ARCPOD48Q

8

3.3 RDM MODE

To use the ARCPOD48Q proceed as follows:

• Connect the ARCPOD48Q to a DATAMASTER.

• Turn on the DATAMASTER using the dedicated button.

• With the DATAMASTER select RDM to show the following info about:

• Model

• Manufacturer

• Function

• Temperature

• Factory Default

• Software Version

• UID

• Manual Color

• Eects mode

• Full On

3.4 MENU STRUCTURE

MENU

1 DMX ADDRESS

ð

001-512 Default: 1

2 DMX MODE

ð

5CH

7CH

10CH

17CH

22CH

Default: 10CH

3 DIMMER MODE

ð

O

Dimmer1

Dimmer2

Dimmer3

Default: O

4 LED FREQUENCY

ð

600Hz

1200Hz

2000Hz

4000Hz

6000Hz

25kHz

Default: 1200Hz

5 SPECIFIC PIDS

ð

8200 (RED)

8201 (Green)

8202 (Blue)

8203 (White)

8217 (Full On Mode)

8206 (Clear Device Hours)

ð

0:HB;1:Studio

White Balance

Default: HB

9

ARCPOD48Q

3.5 LINKING

Multiple units can be connected so that all secondary units have the same lighting eect as the main unit

(Master).

1. 1. Connect the DMX OUT output of the main unit to the DMX IN input of the rst secondary unit using

5 pole XLR cable.

2. 2. Connect the DMX OUT output of the rst secondary unit with the DMX IN input of the second sec-

ondary unit, etc.

3.6 DMX ADDRESSING CONFIGURATION

To enter the DMX mode proceed as follows:

• In the main menu of the DATAMASTER select RDM.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select DMX Addrees, then press the ENTER button

to access.

• Use the arrow buttons to set the desired value (001-512). Press the ENTER button to conrm.

• Press the MENU button repeatedly to exit the menu and to save the changes made.

3.7 DMX MODE CONFIGURATION

ARCPOD48Q has 5 DMX channel congurations.

• In the main menu of the DATAMASTER select RDM

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select the DMX Mode, then press the ENTER but-

ton to enter the next menu.

• Use the UP/DOWN button to select the desired DMX channel conguration (5CH, 7CH, 10CH, 17CH, 22CH),

then press the ENTER button to conrm the selection.

• Press the MENU button repeatedly to exit the menu and to save the changes made.

The tables on page 13, 14 and 15 indicate the operating modes and related DMX values. As an interface

DMX, the unit has 5-pin XLR contacts.

3.8 DMX ADDRESSING

For operation via a light control unit with DMX512 protocol, simply connect ARCPOD48Q to the controller.

The projector has a DMX channel conguration that can be accessed from the control panel. In order to

control ARCPOD48Q with a light control unit, the DMX start address must be set for the rst DMX channel.

If, for example, the address 33 is provided on the control unit to control the function of the rst DMX chan-

nel, the start address 33 must be set on the ARCPOD48Q. The other panel functions will be automatically

assigned to the following addresses.

Number of

DMX chan-

nels

Start address

(example)

DMX Address

occupied

Next possible start

address for unit No. 1

Next possible start

address for unit No. 2

Next possible start

address for unit No. 3

5 33 33-37 38 43 48

7 33 33-39 40 47 54

10 33 33-42 43 53 63

17 33 33-49 50 67 84

22 33 33-54 55 77 99

ARCPOD48Q

10

3.9 DIMMER MODE

To to select specic dimming curve, proceed as follows.

• In the main menu of the DATAMASTER select RDM.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select the Dimmer mode, then press the ENTER

button to access to next menù.

• Press the UP/DOWN button to select one of available setting:

• O: The increase in light intensity is linear.

• Dimmer 1: dimmer curve with low fade.

• Dimmer 2: dimmer curve with medium fade.

• Dimmer 3: dimmer curve with high fade.

• Press ENTER to conrm.

• Press the MENU button repeatedly to exit the menu.

3.10 LED FREQUENCY

To adjust the frequency of the LEDs, proceed as follows.

• In the main menu of the DATAMASTER select RDM.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select the LED Frequency, then press the ENTER

button to access to next menù.

• Press the UP/DOWN button to select one of available setting: 600Hz, 1200Hz, 2000Hz, 4000Hz, 6000Hz, 25kH.

Then select ENTER to conrm.

• Press the MENU button repeatedly to exit the menu.

3.11 SENSOR MENU

To view the information about temperature on the device, proceed as follows.

• In the main menu of the DATAMASTER select RDM.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select the Sensor Menu, then press the ENTER but-

ton to access to next menù to view the temperature.

• Press the MENU button repeatedly to exit the menu.

Fig.5 - Example of a DMX 5-channel conguration

DMX Address:53DMX Address: 43DMX Address: 38 DMX Address: 48

. . . . . . . . . . . .

DMX512 Controller

11

ARCPOD48Q

3.12 SW VERSION

To view the software version installed on the device, proceed as follows.

• In the main menu of the DATAMASTER select RDM.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select the Sw Version, then press the ENTER but-

ton to access to next menù to view the software version of the device.

• Press the MENU button repeatedly to exit the menu.

3.13 UID

To view the UID of the device, proceed as follows.

• In the main menu of the DATAMASTER select RDM.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select the UID, then press the ENTER button to

access to access to next menù to view UID of the device.

Press the MENU button repeatedly to exit the menu.

3.14 FACTORY DEFAULT

To reset the device of the factory default proceed as follows:

• In the main menu of the DATAMASTER select RDM.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select the Factory Default, then press the ENTER

button to access the next menù to choice the Yes or No.

• Press the MENU button repeatedly to exit the menu and to save the changes made.

3.15 MANUAL COLOR

To enter this mode proceed as follows:

• In the main menu of the DATAMASTER select RDM.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select the Manual Color then press the ENTER but-

ton to access.

• Use the arrow buttons to set the desired mixing color (Red, Green, Blue, White) with the relative value (000-

255). Press the ENTER button to conrm.

• Press the MENU button repeatedly to exit the menu and to save the changes made.

• NOTE: once you have set up the mixing of desired colors with the mode described, to change this at a

later time it is necessary to start again with the Factory Reload mode.

3.16 EFFECTS MODE

To enter this mode proceed as follows:

• In the main menu of the DATAMASTER select RDM.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select the Eects then press the ENTER button

• to access.

• Use the arrow buttons to set the desired eect (Eect1, Eect2, Eect3, Eect4, Eect5, Eect6, Eect7, Eect8,

Eect9) with the relative value (000-225). Press the ENTER button to conrm.

• Press the MENU button repeatedly to exit the menu and to save the changes made.

NOTE: once the desired eect has been set with the described mode, to change it at a later time it is neces-

ARCPOD48Q

12

sary to start again with the Factory Reload mode.

3.17 FULL ON MODE

To enter this mode proceed as follows:

• In the main menu of the DATAMASTER select RDM.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select the Full on mode then press the ENTER

button to access.

• Use the UP/DOWN buttons to set the HB mode (High Brightness Mode, with the maxinum value of the

colors) or Studio mode with a automatic white calibration.

• Press the MENU button repeatedly to exit the menu and to save the changes made.

• NOTE: once the desired eect has been set with the described mode, to change it at a later time it is

necessary to start again with the Factory Reload mode.

NOTE: If the projector is in Blackout mode before to receive DMX signal, and if the DMX signal is lost, the

projector will remain on according to the last received DMX value. If the projector was in STATIC or AUTO

mode before to receive DMX signal, if the DMX signal is lost, the projector will return to the previously set

STATIC or AUTO.

13

ARCPOD48Q

3.18 CONNECTION OF THE DMX LINE

DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120Ω imped-

ance and low capacity.

The following diagram shows the connection mode:

ATTENTION

The screened parts of the cable (sleeve) must never be connected to the system’s earth, as this would

cause faulty xture and controller operation.

Over long runs can be necessary to insert a DMX level matching amplier.

For those connections the use of balanced microphone cable is not recommended because it cannot

transmit control DMX data reliably.

• Connect the controller DMX input to the DMX output of the rst unit.

• Connect the DMX output to the DMX input of the following unit. Connect again the output to the input

of the following unit until all the units are connected in chain.

• When the signal cable has to run longer distance is recommended to insert a DMX termination on the

last unit.

3.19 CONSTRUCTION OF THE DMX TERMINATION

The termination avoids the risk of DMX 512 signals being reected back along the cable when they reach-

es the end of the line: under certain conditions and with certain cable lengths, this could cause them to

cancel the original signals.

The termination is prepared by soldering a 120Ω 1/4 W resistor between pins 2 and 3 of the 5-pin male XLR

connector, as shown in gure.

Fig.6

DMX - OUTPUT

XLR socket

DMX - INPUT

XLR plug

Pin1 : GND - Shield

Pin2 : - Negative

Pin3 : + Positive

Pin4 : N/C

Pin5 : N/C

Fig.7

Example:

5 pin XLR connector

ARCPOD48Q

14

3.20 DMX CONTROL

5 CHANNELS

MODE

FUNCTION DMX

Value

5 Ch

1

RED

0~100% 000 - 255

2

GREEN

0~100% 000 - 255

3

BLUE

0~100% 000 - 255

4

WHITE

0~100% 000 - 255

5

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000-051

052-101

102-152

153-203

204-255

10 CHANNELS

MODE

FUNCTION DMX

Value

10 Ch

1

DIMMER

0~100% 000 - 255

2

RED

0~100% 000 - 255

3

GREEN

0~100% 000 - 255

4

BLUE

0~100% 000 - 255

5

WHITE

0~100% 000 - 255

6

STROBE

No function

Strobe Slow to Fast

000 - 010

011 - 255

7

COLOR MACRO

No Function

R 100%, G 0~100%, B 0 %

R 100%~0 %, G 100%, B 0 %

R 0 %, G 100%, B 0~100%

R 0 %, G 100~0 %, B 100%

R 0~100%, G 0 %, B 100%

R 100%, G 0 %, B 100~0 %

R 100%, G 0~100%, B 0~100%

R 100~0 %, G 100~0 %, B 100%

R 100%, G 100%, B 100%, W 100%

2800k

3000k

3200k

4000k

5600k

6000k

6500k

7000k

8000k

9000k

10000k

000 - 010

011 - 030

031 - 050

051 - 070

071 - 090

091 - 110

111 - 130

131 - 150

151 - 170

171 - 200

201 - 205

206 - 210

211 - 215

216 - 220

221 - 225

226 - 230

231 - 235

236 - 240

241 - 245

246 - 250

251 - 255

7 CHANNELS

MODE

FUNCTION DMX

Value

7 Ch

1

DIMMER

0~100% 000 - 255

2

RED

0~100% 000 - 255

3

GREEN

0~100% 000 - 255

4

BLUE

0~100% 000 - 255

5

WHITE

0~100% 000 - 255

6

STROBE

No function

Strobe Slow to Fast

000 - 010

011 - 255

7

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000-051

052-101

102-152

153-203

204-255

15

ARCPOD48Q

10 CHANNELS

MODE

FUNCTION DMX

Value

10 Ch

8

EFFECTS

NO Function

Eect 1

Eect 2

Eect 3

Eect4

Eect5 (Eects1- 4)

Eect 6

Eect 7

Eect 8

Eect 9 (Eects6- 8)

000-010

011-037

038-064

065-091

092-118

119-145

146-172

173-199

200-226

227-255

9

EFFECTS SPEED

Eects speed slow to fast 000 - 255

10

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode 1 (fast speed)

Dimmer speed mode 2 (middle speed)

Dimmer speed mode 3 (slow speed)

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

17 CHANNELS

MODE

FUNCTION DMX

Value

17 Ch

1

RED 1

0~100% 000 - 255

2

GREEN 1

0~100% 000 - 255

3

BLUE 1

0~100% 000 - 255

4

WHITE 1

0~100% 000 - 255

5

RED 2

0~100% 000 - 255

6

GREEN 2

0~100% 000 - 255

7

BLUE 2

0~100% 000 - 255

8

WHITE 2

0~100% 000 - 255

9

RED 3

0~100% 000 - 255

10

GREEN 3

0~100% 000 - 255

11

BLUE 3

0~100% 000 - 255

12

WHITE 3

0~100% 000 - 255

13

RED 4

0~100% 000 - 255

14

GREEN 4

0~100% 000 - 255

15

BLUE 4

0~100% 000 - 255

16

WHITE 4

0~100% 000 - 255

17

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000-051

052-101

102-152

153-203

204-255

ARCPOD48Q

16

22 CHANNELS

MODE

FUNCTION DMX

Value

22 Ch

1

DIMMER

0~100% 000 - 255

2

STROBE 1

No function

Strobe Slow to Fast

000 - 010

011 - 255

3

STROBE 2

No function

Strobe Slow to Fast

000 - 010

011 - 255

4

STROBE 3

No function

Strobe Slow to Fast

000 - 010

011 - 255

5

STROBE 4

No function

Strobe Slow to Fast

000 - 010

011 - 255

6

RED 1

0~100% 000 - 255

7

GREEN 1

0~100% 000 - 255

8

BLUE 1

0~100% 000 - 255

9

WHITE 1

0~100% 000 - 255

10

RED 2

0~100% 000 - 255

11

GREEN 2

0~100% 000 - 255

12

BLUE 2

0~100% 000 - 255

13

WHITE 2

0~100% 000 - 255

14

RED 3

0~100% 000 - 255

15

GREEN 3

0~100% 000 - 255

16

BLUE 3

0~100% 000 - 255

17

WHITE 3

0~100% 000 - 255

22 CHANNELS

MODE

FUNCTION DMX

Value

22 Ch

18

RED 4

0~100% 000 - 255

19

GREEN 4

0~100% 000 - 255

20

BLUE 4

0~100% 000 - 255

21

WHITE 4

0~100% 000 - 255

22

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000-051

052-101

102-152

153-203

204-255

17

ARCPOD48Q

- 4 - MAINTENANCE

4.1 MAINTENANCE AND CLEANING THE UNIT

• Make sure the area below the installation place is free from unwanted persons during setup.

• Switch o the unit, unplug the main cable and wait until the unit has cooled down.

• All screws used for installing the device and any of its parts should be tightly fastened and should not

be corroded.

• Housings, xations and installation spots (ceiling, trusses, suspensions) should be totally free from any

deformation.

• When the lens is visibly damaged due to cracks or deep scratches, it must be replaced.

• The main cables must be in impeccable condition and should be replaced immediately even when a

small problem is detected.

• In order to protect the device from overheating the cooling fans (if any), and ventilation openings

should be cleaned monthly.

To ensure optimal operation and performance for a long time it is essential to periodically clean the parts

subject to dust and grease deposits. The frequency with which the following operations are to be carried

out depends on various factors, such as the amount of the eects and the quality of the working environ-

ment (air humidity, presence of dust, salinity, etc.). Use a soft cloth dampened with any detergent liquid

for cleaning glass to remove the dirt from the reectors, from the lenses and lters.

It is recommended that the projector undergoes an annual service by a qualied technician for special

maintenance involving at least the following operations:

- General cleaning of internal parts..

- Restoring lubrication of all parts subject to friction, using lubricants specically.

- General visual check of the internal components, cabling, mechanical parts, etc.

- Electrical, photometric and functional checks; eventual repairs.

Warning: we strongly recommend internal cleaning to be carried out by qualied personnel!

4.2 TROUBLESHOOTING

Problems Possible causes Checks and remedies

Fixture does not light up

• No mains supply

• Dimmer fader set to 0

• All color faders set to 0

• Faulty LED

• Faulty LED board

• Check the power supply voltage

• Increase the value of the dimmer channels

• Increase the value of the color channels

• Replace the LED board

General low light intensity

• Dirty lens assembly

• Misaligned lens assembly

• Clean the xture regularly

• Install lens assembly properly

Fixture does not power up

• No power

• Loose or damaged power cord

• Faulty internal power supply

• Check for power on power outlet

• Check power cord

• Replace internal power supply

Fixture does not respond to DMX

• Wrong DMX addressing

• Damaged DMX cables

• Bouncing signals

• Check control panel and unit addressing

• Check DMX cables

• Install terminator as suggested

Contact an authorized service center in case of technical problems or not reported in the table can not be

resolved by the procedure given in the table.

Note

La pagina sta caricando ...

ProLights ARCPOD48Q Manuale utente

ProLights ARCPOD48Q Manuale utente

in altre lingue

Documenti correlati

Altri documenti