Simplicity SPX110 Manuale utente

80029484WST

Revision A

1

2

3

4

5

6

7

2

8

9

10

11

12

13

14

15

3

16

17

18

4

Manual Contents:

Products Covered by This Manual......................................5

General Information..............................................................5

European Office Contact Information.................................5

Operator Safety.....................................................................5

Features and Controls..........................................................7

Operation...............................................................................8

Maintenance.........................................................................13

Storage.................................................................................15

Troubleshooting..................................................................16

Specifications......................................................................17

Products Covered by This

Manual

The following products are covered by this manual:

2691487-00

General Information

For additional information, refer to the

Customer Contact Guide

and

Setup Instructions

included with the unit.

The illustrations in this document are representative. Your unit

may vary from the images shown.

LEFT

and

RIGHT

are

referenced from the operating position.

The use of Important and Note in the text indicates clarifications,

exceptions, or alternatives to the procedures given.

All language translations of this document are derived from the

original English source file.

All packaging, used oil, and batteries should be recycled

according to applicable government regulations.

European Office Contact

Information

For questions regarding European emissions, please contact

our European office at:

Max-Born-Straße 2, 68519 Viernheim, Germany.

Operator Safety

Save these instructions for future reference. This manual

contains safety information to make you aware of the hazards

and risks associated with the product and how to avoid them.

It also contains important instructions that should be followed

during the initial set-up, operation, and maintenance of the

product.

This product is designed and intended for cutting well maintained

grass and is not intended for any other purpose.

It is important that you read and understand these instructions

before attempting to start or operate this equipment.

Be thoroughly familiar with the controls and the proper use of

the product.

Know how to stop the unit and disengage controls quickly.

Slope Identification Guide

How to measure the slope of a lawn surface with a

smartphone or an angle finder tool:

WARNING

Do not operate on slopes greater than 10 degrees.

1. Use a straight edge at least two (2) feet long (A, Figure 1).

A 2x4 or a straight piece of metal works well.

2. Angle finder tools.

a. Use your smartphone: Many smartphones (B, Figure

1) have an inclinometer (angle finder) located under

the compass application (app). Or, search an app store

for an Inclinometer app.

b. Use angle finder tools: Angle finder tools (C & D,

Figure 1) are available at local hardware stores or online

(also called inclinometer, protractor, angle meter, or

angle gauge). Dial type (C) or digital type (D) work,

others may not. Follow user instructions with the angle

finder tool.

3. Place the two (2) feet long straight edge along the steepest

part of the lawn slope. Place the board up and down the

slope.

4. Lay the smartphone or angle finder tool on the straight edge

and read the angle in degrees. This is the slope of your

lawn.

Note:

A paper gauge slope identification guide is included in

your product literature packet and is also available to download

from the manufacturer's website.

Safety Symbols and Meanings

MeaningSymbolMeaningSymbol

Read and

understand the

operator's manual

before operating or

servicing the unit.

Safety information

about hazards that can

result in personal

injury.

5

MeaningSymbolMeaningSymbol

StopRemove the key before

performing service.

Read the operator's

manual before

performing service.

Explosion hazardFire hazard

Toxic fume hazardShock hazard

Wear eye protectionMoving parts

Hot surface hazardHazardous chemical

Thrown objects

hazard

Amputation hazard

Keep children awayKeep a safe distance

Amputation hazardRoll-over hazard

Safety Alert Symbol and Signal Words

The safety alert symbol identifies safety information about

hazards that can result in personal injury. A signal word

(DANGER, WARNING, or CAUTION) is used with the alert

symbol to indicate the likelihood and the potential severity of

injury. In addition, a hazard symbol may be used to represent

the type of hazard.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could

result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE

indicates an action that could result in damage to the

product.

Safety Decals

Before operating your machine, read and understand the safety

decals. Compare Figure 2 with the table following. The cautions

and warnings are for your safety. To avoid a personal injury or

damage to the machine, understand and follow all the safety

decals.

If any safety decals become worn or damaged, and cannot be

read, order replacement decals from your local dealer.

A

B

C

D

6

Safety Decal Icons

WARNING: Read and understand the Operator’s Manual before

using this machine. Know the location and function of all controls.

Do not operate this machine unless you are trained.

1

DANGER - LOSS OF TRACTION, SLIDING, STEERING AND

CONTROL ON SLOPES HAZARD: If machine stops forward

motion or starts sliding on a slope, stop the blades and drive slowly

off the slope.

2

DANGER: FIRE HAZARD: Keep unit free of grass, leaves and

excess oil. Do not add fuel while engine is hot or running. Stop

engine, remove key and allow to cool for at least 3 minutes prior

to adding fuel. Do not add fuel indoors, in an enclosed trailer,

garage or other enclosed areas. Clean up spilled fuel. Do not

smoke while operating this machine.

3

DANGER - TIPPING AND SLIPPING HAZARD: Mow up and

down slopes not across. Do not operate on slopes over 10

degrees. Avoid sudden and sharp (fast) turns while on slopes.

4

DANGER - AMPUTATION AND DISMEMBERMENT HAZARD:

To avoid injury from rotating blades and moving parts, keep safety

devices (guards, shields and switches) in place and working.

5

Do not mow when children or others are around. Never carry riders

especially children even with the blades off. Do not mow in reverse

unless absolutely necessary. Look down and behind – before and

while backing.

6

Consult technical literature before performing technical repairs or

maintenance. When leaving the machine, shutoff engine, set the

parking brake to the lock position and remove the ignition key.

7

Keep by-standers and children a safe distance away. Remove

objects that can be thrown by the blade. Do not mow without

discharge chute in place.

8

Do not mow without discharge chute or entire grass catcher in

place.

9

To avoid injury from rotating blades, stay clear of deck edge and

keep others away.

10

Safety Messages

WARNING

Read, understand, and follow all the instructions and warnings

in the operator's manual and on the machine, engine, and

attachments before operating this machine. Failure to observe

the safety instructions in this manual and on the equipment

could result in death or serious injury.

• Only allow operators who are responsible, trained and

familiar with the instructions and physically capable to

operate the machine.

• Do not operate the machine while under the influence of

alcohol or drugs.

• Wear safety glasses and closed toe footwear.

• Do not put hands or feet near rotating parts or under the

machine. Keep clear of the discharge opening at all times.

• Keep the machine in good working order. Replace worn

or damaged parts.

• Be careful when servicing blades. Wrap the blade(s) or

wear gloves. Replace damaged blades. Do not repair or

alter blade(s).

• Use full width ramps for loading and unloading a machine

for transport.

• See attachment or accessory for proper wheel weights

or counterweights.

• To help prevent fires, keep machine free of grass, leaves,

or other debris build up; clean up oil or fuel spillage and

remove any fuel soaked debris and allow the machine to

cool before storing.

WARNING

Running engine gives off carbon monoxide, an odorless,

colorless, poison gas. Breathing carbon monoxide can cause

headaches, fatigue, dizziness, vomiting, confusion, seizures,

nausea, fainting or death.

• Operate equipment ONLY outdoors.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes, or other openings.

Features and Controls

Match the callout letters in Figure 3 to the features and controls

that match your machine listed in the accompanying table.

Control Symbols and Meaning

Reverse Mowing OptionA

7

Hourmeter (if equipped)B

Ignition SwitchC

OFF

RUN

Start

Headlight Switch

Power Take-Off Switch Up, Engage BladesD

Power Take-OffE

Power Take-Off Switch Down, Disengage BladesF

Cruise ControlG

Parking BrakeH

Throttle ControlI

Throttle Control SLOW PositionJ

Throttle Control FAST PositionK

ChokeL

Ground Speed PedalsM

Mower Height of Cut AdjustmentN

Transmission Release LeverO

Fuel TankP

Brake PedalR

Seat Adjustment Lever (if equipped)S

Operation

Operating Area

1. Familiarize yourself with the area in which you plan to

operate the rider mower.

2. Make sure that the area is free of debris or objects that

could be picked up by the blades and thrown.

DANGER

This machine is capable of throwing objects that could injure

bystanders or cause damage to buildings.

• Do not operate the machine without the entire grass

catcher, discharge chute, or other safety devices in place

and functioning properly. Check frequently for signs of

wear or detoriation and replace as needed.

• Clear the operating area of any objects which could be

thrown by or interfere with the operation of the machine.

3. Move the rider mower outside, before you start the engine.

8

WARNING

Engines give off carbon monoxide, an odorless, colorless,

poison gas. Breathing carbon monoxide can cause nausea,

fainting, or death.

4. Note all slopes and drop-offs.

DANGER

Operating on slopes, or near water, or drop-offs can result in

loss of control and roll-over.

• Mow up and down slopes not across.

• Reduce speed and be careful on slopes.

• Do not operate on slopes over 10 degrees, which is a 3.5

foot rise over a 20 foot length.

• Give yourself a minimum of two mower widths of clearance

around water, retaining walls, or drop-offs.

• Avoid mowing wet grass.

• Do not operate machine under any condition where

traction, steering, or stability is in question. Tires could

slide even if the wheels are stopped.

• Avoid starting and stopping on slopes.

• Avoid making sudden changes in speed or direction.

• Make turns slowly and gradually.

• Be careful while operating machine with a grass catcher

or other attachment(s). They can affect the stability of the

machine.

• Follow the manufacturer's recommendation for weight

limits for towed equipment and towing on slopes (refer to

Towed Equipment

).

5. Be sure the operating area is clear of bystanders, especially

children.

DANGER

This rider mower is capable of amputating hands and feet.

• Stop the mower when children or others are near.

• Keep children out of the operating area and under the

watchful care of a responsible adult.

• Do not carry passengers, especially children, even with

the blade(s) shut off. Children can fall off and be seriously

injured or interfere with the safe machine operation.

Children who have been given rides in the past can

suddenly appear in the mowing area for another ride and

be run over or backed over by the machine.

• Use care when approaching blind corners, shrubs, trees,

or other objects that obscure vision.

Safety Interlock System Tests

This machine is equipped with a Safety Interlock System. Do

not attempt to bypass or tamper with the switches/devices.

WARNING

If the machine does not pass a safety test, do not operate the

machine. See an authorized dealer.

Test 1 — Engine should NOT crank if:

• PTO switch is ON, OR

• Brake pedal is NOT fully depressed (parking brake OFF),

OR

• Operator is NOT sitting in seat.

Test 2 — Engine SHOULD crank and start if:

• Operator is sitting in seat, AND

• PTO switch is OFF, AND

• Brake pedal is fully depressed (parking brake ON).

Test 3 — Engine should SHUT OFF if:

• Operator rises off seat.

Test 4 — Check Mower Blade Stopping Time

Mower blades and mower drive belt should come to a complete

stop within five seconds after electric Power Take-Off (PTO)

switch is turned OFF. If mower drive belt does not stop within

five seconds, see an authorized dealer.

Test 5 — Reverse Mowing Option (RMO) Check

• Engine should shut off if reverse travel is attempted if the

Power Take-Off (PTO) has been switched on and Reverse

Mowing Option (RMO) has been activated.

• Reverse Mowing Option (RMO) light should illuminate when

RMO has been activated.

DANGER

Mowing in reverse can be hazardous to bystanders. Tragic

accidents can occur if the operator is not alert to the presence

of children. Never activate the Reverse Mowing Option (RMO)

if children are present. Children are often attracted to the

machine and the mowing activity.

Engine

Check and Add Engine Oil

Use of Briggs & Stratton Warranty Certified oils for best

performance. Other high-quality detergent oils are acceptable

if classified for service SF, SG, SH, SJ or higher. Do not use

special additives.

Outdoor temperatures determine the proper oil viscosity for

the engine. Use the chart to select the best viscosity for the

outdoor temperature range expected.

9

SAE 30 - Below 40 °F (4 °C) the use of SAE 30 will result in hard starting.A

10W-30 - Above 80 °F (27 °C) the use of 10W-30 may cause increased

oil consumption. Check oil level more frequently.

B

5W-30C

Synthetic 5W-30D

Vanguard™ Synthetic 15W-50E

*Below 40°F (4°C) the use of SAE 30 will result in hard starting

.

**Above 80°F (27°C) the use of 10W-30 may cause increased oil consumption.

Check oil level more frequently.

1. Place the tractor on a level surface (Figure 4).

2. Stop the engine and remove the key.

3. Clean the oil fill area of any debris.

4. Remove the dipstick and wipe with a clean cloth.

5. Fully insert the dipstick.

6. Remove the dipstick (A, Figure 5) and check the oil level.

It should be at the FULL mark (B) on the dipstick.

7. If FULL, insert the dipstick and tighten securely.

8. If LOW, add oil slowly into the engine oil fill tube (C ) . Do

not overfill. After adding oil, wait one minute, then recheck

the oil level.

Note:

Do not add oil at the quick oil drain (if equipped).

9. Replace and tighten the dipstick.

Oil Pressure

If the oil pressure is too low, a pressure switch (if equipped)

will either stop the engine or activate a warning device on the

equipment. If this occurs, stop the engine and check the oil

level with the dipstick.

If the oil level is below the ADD mark, add oil until it reaches

the FULL mark. Start the engine and check for proper pressure

before continuing to operate.

If the oil level is between the ADD and FULL marks, do not

start the engine. Contact an authorized dealer to have the oil

pressure problem corrected.

Add Fuel

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane / 87 AKI (91 RON). For high

altitude use, see below.

• Gasoline with up to 10% ethanol (gasohol) is acceptable.

NOTICE

Do not use unapproved gasolines, such as E15

and E85. Do not mix oil in gasoline or modify the engine to

run on alternate fuels. Use of unapproved fuels will cause

damage to engine components, which will not be covered

under warranty.

To protect the fuel system from gum formation, mix a fuel

stabilizer into the fuel. See Storage. All fuel is not the same. If

starting or performance problems occur, change fuel providers

or change brands. This engine is certified to operate on gasoline.

The emissions control system for this engine is EM (Engine

Modifications).

High Altitude requirements:

• At altitudes over 5,000 feet (1524 meters), a minimum 85

octane / 85 AKI (89 RON) gasoline is acceptable.

• For carbureted engines, high altitude adjustment is required

to remain emissions compliant. Operation without this

adjustment will cause decreased performance, increased

fuel consumption, and increased emissions. Contact a

Briggs & Stratton Authorized Service Dealer for high altitude

adjustment information.

• Operation of the engine at altitudes below 2,500 feet (762

meters) with the high altitude adjustment is not

recommended.

• For Electronic Fuel Injection (EFI) engines, no high altitude

adjustment is necessary.

WARNING

Fuel and its vapors are extremely flammable and explosive.

Always handle fuel with extreme care.

Failure to observe these safety instructions can cause fire or

explosion which could result in severe burns or death.

When Adding Fuel

• Turn engine off and let engine cool at least 3 minutes

before removing the fuel cap.

• Extinguish all cigarettes, cigars, pipes, and other souces

of ignition.

• Fill fuel tank outdoors or in well-ventilated area.

• Do not overfill fuel tank. To allow for expansion of the fuel,

do not fill above the bottom of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot lights,

heat, and other ignition sources.

• Check fuel lines, tank, cap, and fittings frequently for

cracks or leaks. Replace if necessary.

• If fuel spills, wait until it evaporates before starting engine.

• Use only an approved fuel container.

1. Clean the fuel cap area of dirt and debris.

10

2. Remove the fuel cap (A, Figure 6). Also see Features and

Controls section.

3. Fill the fuel tank (B) with fuel. To allow for expansion of the

fuel, do not fill above the bottom of the fuel tank neck (C).

4. Reinstall the fuel cap.

Start the Engine

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

When Starting the Engine

• Ensure that spark plug, muffler, fuel cap, and air cleaner

(if equipped) are in place and secured.

• Do not crank engine with spark plug removed.

• If engine floods, set choke (if equipped) to OPEN/RUN

position, move throttle (if equipped) to FAST position and

crank until engine starts.

WARNING

Engines give off carbon monoxide, an odorless, colorless,

poison gas.

Breathing carbon monoxide can cause nausea, fainting, or

death.

Fire or explosion can cause severe burns or death.

• Start and run engine outdoors.

• Do not start or run engine in enclosed area, even if doors

or windows are open.

1. Check the oil level (refer to

Check and Add Engine Oil

).

2. Make sure equipment drive controls are disengaged.

3. Sit in the seat and lift UP the seat adjustment lever to lock

the seat in position.

4. Engage the parking brake. Push the brake pedal, pull UP

on the parking brake control, and release the brake pedal.

5. Disengage PTO switch by pushing IN.

6. Set the throttle/choke control to the CHOKE position.

7. Insert the key into the ignition switch and turn it to the

ON/START position.

8. After the engine starts, move the throttle/choke control to

half speed. Warm up the engine by running it for at least

30 seconds.

9. Set throttle/choke control to the FAST position,

In the event of an emergency the engine can be stopped by

simply turning the ignition swtch to STOP. For normal engine

shut down follow the procedure given in

Stop Tractor and

Engine

.

Note:

If the engine does not start after repeated attempts,

contact an authorized dealer.

Stop Tractor and Engine

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

• Do not choke the carburetor to stop the engine.

1. Release the ground speed pedals (A, Figure 7) to return to

the NEUTRAL position.

2. While still on the lawn, disengage the PTO switch (B), then

wait for all moving parts to stop.

3. Move the throttle control (C) (or throttle/choke control) to

SLOW position and turn the ignition key (D) to OFF.

4. Remove the key.

5. Engage the parking brake (E). Push the brake pedal (F),

pull UP on the parking brake control, and release the brake

pedal.

In the event of an emergency the engine can be stopped by

simply turning the ignition switch to STOP.

Tractor Operation

1. Sit in the seat and adjust the seat so that you can

comfortably reach all the controls (refer to

Features and

Controls

).

2. Engage the parking brake.

a. Fully depress the brake pedal.

b. Pull UP on the parking brake control

c. Release the brake pedal.

3. Make sure the PTO switch is disengaged.

4. Start the engine (refer to

Start Engine

).

5. Disengage the parking brake.

a. Fully depress the brake pedal.

b. Press DOWN on the parking brake control.

c. Release the brake pedal.

6. Depress the forward ground speed control pedal to travel

forward. Release the pedal to stop.

Note:

The further down the pedal is depressed the faster the

tractor will travel.

7. Stop the tractor by releasing the ground speed control

pedals, setting the parking brake, and stopping the engine

(see Stop Tractor and Engine).

Cruise Control

To engage:

11

1. Push the forward ground speed Pedal (refer to

Features

and Controls

).

2. Pull up the cruise control when the desired speed is

reached. The cruise will lock in one of its five locking

positions.

To disengage:

1. Push the brake pedal (refer to

Features and Controls

). OR

2. Push the forward ground speed pedal.

Mowing

DANGER

This machine is capable of amputating hands and feet, and

throwing objects. Failure to observe the following safety

instructions could result in serious injury or death.

• Only operate the machine in daylight hours or good

artificial light.

• Avoid holes, ruts, bumps, rocks, or other hidden hazards.

Uneven terrain can overturn the machine or cause

operator to lose their balance or footing.

• Do not direct discharge material toward anyone. Avoid

discharging material against a wall or obstruction as

material may ricochet back toward the operator.

• Stop the blade(s) when crossing gravel surface.

• Do not leave a running machine unattended. Always park

on level ground, disengage the attachment, set parking

brake, stop engine and remove starter insert or key.

1. Engage the parking brake (B, Figure 8).

2. Make sure the PTO switch (C) is disengaged.

3. Start the engine (refer to

Start Engine

).

4. Set the throttle control (D) to the FAST position.

5. Engage the PTO to activate the mower blades.

6. Use the Height-of-Cut Lever (A) to set the cutting height to

the desired level.

7. Disengage the parking brake, then begin mowing.

8. When finished mowing, shut off the PTO.

9. STOP the engine (refer to

Stop Tractor and Engine

).

WARNING

The engine will shut off if the reverse ground speed pedal is

depressed while the PTO is on and the RMO has not been

activated. The operator should always turn the PTO off prior

to driving across on roads, paths, or any area that may be

used by other vehicles. Sudden loss of drive could create a

hazard.

Reverse Mowing Option (RMO)

DANGER

Mowing in reverse can be hazardous to bystanders. Tragic

accidents can occur if the operator is not alert to the presence

of children. Children are often attracted to the machine and

the mowing activity. Never assume that children will remain

where you last saw them.

• Keep children out of the operating area and under the

watchful care of a responsible adult.

• Do not carry passengers, especially children, even with

the blade(s) shut off. Children can fall off and be seriously

injured or interfer with the safe machine operation.

Children who have been given rides in the past can

suddenly appear in the mowing area for another ride and

be run over or backed over by the machine

• Do not mow in reverse unless absolutely necessary.

Always look down and behind before and while backing.

• If the machine mows in reverse without Reverse Mowing

Option activated, see an authorized dealer immediately.

The Reverse Mowing Option (RMO) allows the operator to mow

in reverse.

To activate:

1. Engage the Power Take-Off (PTO) (B, Figure 9).

2. Turn the Reverse Mowing Option (RMO) key (A) to ON.

3. The L.E.D. light illuminates.

4. The operator mows in reverse.

Note:

The key should be removed to restrict access to the RMO.

12

Maintenance

WARNING

Unintentional sparking can result in fire or electric shock.

Unintentional start-up can result in entanglement, traumatic

amputation, or laceration.

Before performing adjustments or repairs:

• Disconnect the spark plug wire and keep it away from the

spark plug.

• Disconnect battery at negative terminal (only engines with

electric start).

• Use only correct tools.

• Do not tamper with governor spring, links, or other parts

to increase engine speed.

• Replacement parts must be of the same design and

installed in the same position as the original parts. Other

parts may not perform as well, may damage the unit, and

may result in injury.

• Do not strike the flywheel with a hammer or hard object

because the flywheel may shatter during operation.

Maintenance Schedule

RIDER AND MOWER

Every 8 Hours or Daily

Check safety interlock system

Clean debris off rider and mower deck

Clean debris from engine compartment

Every 25 Hours or Annually*

Check tire pressure

Check mower blade stopping time

Check rider and mower for loose hardware

Every 50 Hours or Annually*

Clean battery and cables

Check rider brakes

See Dealer Annually to

Lubricate rider and mower

Check mower blades**

* Whichever come first.

** Check blades more often in regions with sandy soils or high dust

conditions.

ENGINE

First 5 Hours

Change engine oil

Every 8 Hours or Daily

Check engine oil level

Every 25 Hours or Annually*

Clean engine air filter and pre-cleaner**

ENGINE

Every 50 Hours or Annually*

Change engine oil

Replace oil filter

Annually

Replace air filter

Replace pre-cleaner

See Dealer Annually to

Inspect muffler and spark arrester

Replace spark plug

Replace fuel filter

Clean engine air cooling system

* Whichever comes first.

** Clean more often in dusty conditions or when airborne debris is present.

Check Tire Pressure

For proper traction and for the best mowing performance,

regularly check the tire inflation pressure. Refer to Check Tire

Pressure in the

Maintenance Schedule

and to Tire Inflation

Pressure in the

Specifications Chart

.

Clean the Battery and Cables

WARNING

When removing or installing battery cables, disconnect the

negative cable FIRST and reconnect it LAST. If not done in

this order, the positive terminal can be shorted to the frame

by a tool.

1. Disconnect the cables from the battery, negative (-) cable

first.

2. Remove the battery hold-down strap and battery.

3. Clean the battery compartment with a solution of baking

soda and water.

4. Clean the battery terminals and cable ends with a wire brush

and battery terminal cleaner until shiny.

5. Reinstall the battery in the battery compartment, and secure

with the battery hold-down strap.

6. Reattach the battery cables, positive (+) cable first (A, B,

Figure 10).

7. Coat the cable ends and battery terminals with petroleum

jelly or non-conducting grease.

Charge the Battery

WARNING

Keep open flames and sparks away from the battery; the

gasses coming from it are highly explosive. Ventilate the

battery well during charging.

13

A dead battery or one too weak to start the engine may be the

result of a defect in the charging system or other electrical

component. If there is any doubt about the cause of the problem,

see your dealer. If you need to replace the battery, follow the

steps under

Clean the Battery and Cables

.

To charge the battery, follow the instructions provided by the

battery charger manufacturer as well as all warnings included

in the safety rules sections of this book. Charge the battery until

fully charged. Do not charge at a rate higher than 10 amps.

Check Mower Blade Stop Time

WARNING

If the mower blade does not come to a complete stop within

5 seconds, the clutch must be adjusted. Do not operate the

machine until the proper adjustment has been performed by

an authorized dealer.

Mower blades and mower drive belt should come to a complete

stop within five seconds after electric Power Take-Off (PTO)

switch is turned OFF. If mower drive belt does not stop within

five seconds, see an authorized dealer for repairs.

Change the Engine Oil

1. Run engine until warm.

2. Place the rider on a level surface (refer to Figure 11).

3. Stop the engine and remove starter insert (A, Figure 11) or

key.

4. Clean oil fill and filter areas of any debris.

5. Remove dipstick (B) and lay on clean cloth.

6. Disconnect the oil drain hose (A, Figure 12).

7. Carefully remove cap (B) and lower hose into an approved

container (C).

8. After the oil has drained, install cap tightly, then attach the

hose to the side of the engine.

9. Remove the oil filter (B, Figure 13) and dispose of properly

10. Lightly lubricate the oil filter gasket (A) with fresh, clean oil..

11. Install the oil filter by hand until the gasket contacts the oil

filter adapter (C), then tighten the oil filter 1/2 to 3/4 turns.

12. Add oil (refer to the

Check and Add Engine Oil

section).

Air Filter Assembly (Cartridge with

pre-cleaner)

WARNING

Never start or run the engine with the air cleaner assembly or

air filter removed as it is a fire hazard.

NOTICE

Do not use pressurized air or solvents to clean the filter.

Pressurized air can damage the filter and solvents will dissolve

the filter.

1. Loosen the fasteners (A, Figure 14) and remove the cover

(B).

2. Remove the air cleaner assembly (C) and disassemble.

3. Clean up any possible debris that might get into the

carburetor throat (D).

4. Remove the pre-cleaner from the air filter.

5. To loosen debris, gently tap the air filter on a hard surface.

If the air filter is excessively dirty, replace with a new air

filter.

6. Wash the pre-cleaner in liquid detergent and water. Then

allow it to thoroughly air dry. Do not oil the pre-cleaner.

7. Assemble the dry pre-cleaner to the air filter.

8. Install the air filter assembly.

9. Install the cover and secure the fasteners.

Check the Spark Plugs

WARNING

Unintentional sparking can result in fire or electric shock.

Unintentional start-up can result in entanglement, traumatic

amputation, or laceration.

When testing for spark:

• Use approved spark plug tester.

• Do not check for spark with spark plug removed.

NOTICE

Spark plugs have different heat ranges. It is important that

the correct spark plug is used, otherwise, engine damage can

occur. Replace the spark plug with the same type or equivalent

one.

Clean Spark Plug

Clean with wire brush and sturdy knife. Do NOT use abrasives.

Check Spark Plug Gap

Use a spark plug feeler gauge (A, Figure 15) to check the gap

between the two electrodes. When the gap is correct, the gauge

will drag slightly as you pull it through the gap.

If necessary, use the spark plug gauge to adjust the gap by

gently bending the curved electrode without touching the center

electrode or the porcelain.

Install Spark Plug

Finger tighten, then tighten with wrench as shown in Figure 16.

14

• 180 in-lbs (20 Nm), OR

• 1/2 turn when reinstalling the original spark plug. 1/4 turn

when installing a new spark plug.

Push the Tractor by Hand

To push the tractor, perform the following:

1. Disengage the Power Take-Off (PTO) (A, Figure 17).

2. Turn the engine off.

3. Pull the transmission release to lock into the released

position.

4. The tractor can be pushed by hand

WARNING

Towing the unit will cause transmission damage. Do not use

another vehicle to push or pull this machine. Do not actuate

the transmission release lever while engine is running.

Towed Equipment

1. Tow only with a machine that has a hitch designed for

towing.

2. Do not attach towed equipment except at the hitch point.

3. Follow the recommendations for weight limit for towed

equipment and towing on slopes as listed below.

• Gross weight (trailer and load) of 400 pounds.

• Maximum of 20 pound foot up or down on the tongue.

• Go from a 10 degree limit to a 5 degree limit on any

slope.

4. Never allow children or others in or on towed equipment.

5. On slopes, the weight of the towed equipment may cause

loss of traction and loss of control.

6. Travel slowly and allow extra distance to stop.

7. Do not shift to neutral and coast down hill.

Wash the Mower Deck (if equipped)

Note:

Use the washout port (C, Figure 18) to clean the underside of

the mower deck.

1. Place the rider on a smooth level surface.

2. Attach the quick disconnect (A, Figure 18) to the garden

hose (B) and then connect to the washout port (C) on the

mower deck.

3. Turn the water on.

4. Sit in the seat and start the engine.

5. Set the Height-of-Cut in the highest position.

6. Engage the Power Take-Off (PTO) switch to activate the

mower blades. The rotation of the blades and the running

water will clean the underside of the mower deck.

7. Disengage the Power Take-Off and stop the engine.

8. Turn the water off.

9. Remove the garden hose and quick disconnect from the

washout port (C).

Storage

WARNING

Never store the unit (with fuel) in an enclosed, unventilated

structure. Fuel vapors can travel to an ignition source (such

as a furnace, water heater, etc.) and cause an explosion.

• Store away from furnaces, stoves, water heaters, or other

appliances that have pilot lights or other ignition sources

because they can ignite fuel vapors.

Equipment

Disengage the Power Take-Off (PTO), set the parking brake,

and remove the starter insert.

Allow the machine to cool.

Battery life will be increased if it is removed. Put in a cool, dry

place and keep fully charged during storage. If the battery is

left in the unit, disconnect the negative cable.

Fuel System

Fuel can become stale when stored over 30 days. Stale fuel

causes acid and gum deposits to form in the fuel system or on

essential carburetor parts. To keep fuel fresh, use Briggs &

Stratton® Advanced Formula Fuel Treatment & Stabilizer,

available wherever Briggs & Stratton genuine service parts are

sold.

There is no need to drain gasoline from the engine if a fuel

stabilizer is added according to instructions. Run the engine for

2 minutes to circulate the stabilizer throughout the fuel system

before storage. If gasoline in the engine has not been treated

with a fuel stabilizer, it must be drained into an approved

container. Run the engine until it stops from lack of fuel. The

use of a fuel stabilizer in the storage container is recommended

to maintain freshness.

Engine Oil

While the engine is still warm, change the engine oil.

Before starting the machine after it has been stored:

• Check all fluid levels. Check all maintenance items.

• Perform all recommended checks and procedures found in

this manual.

• Allow the engine to warm up for several minutes before use.

15

Troubleshooting

Troubleshooting the Rider

REMEDYLOOK FORPROBLEM

Fully depress brake pedal.Brake pedal not depressed.Engine will not turnover or start.

If engine is hot, allow engine to cool, then refill the

fuel tank.

Out of fuel.

Place in OFF position.PTO switch is in ON position.

Move knob to NEUTRAL/OFF position.Cruise control engaged.

Disengage the choke.Engine flooded.

Refer to

Clean the Battery and Cables

.Battery terminals require cleaning.

Charge or replace battery.Battery discharged or dead.

Visually check wiring. If wires are frayed or broken,

see authorized dealer.

Wiring loose or broken.

Clean air filter.Fuel mixture too rich.Engine starts hard or runs poorly.

Check/add oil as required.Low oil level.Engine knocks.

Refer to the

Check and Add Engine Oil

section.Using wrong grade of oil.

Refer to the

Check and Add Engine Oil

section.Using wrong grade of oil.Excessive oil consumption.

Drain excess oil.Too much oil in crankcase.

Refer to the

Service the Air Filter

section.Dirty air filter.Engine exhaust is black.

Open choke.Choke closed.

Depress pedals.Ground speed control pedals not depressed.Engine runs, but rider will not drive.

Move into DRIVE position.Transmission release lever in PUSH position.

Disengage parking brake.Parking brake is engaged.

Refer to the

Check Tire Pressure

section.Improper tire inflation.Rider steers hard or handles poorly.

Note:

For all other problems, contact an Authorized Service Dealer.

Troubleshooting the Mower

REMEDYLOOK FORPROBLEM

Refer to the

Check Tire Pressure

section.Rider tires not properly inflated.Mower cut is uneven.

Set to FAST throttle.Engine speed too slow.Mower cut is rough looking.

Slow down.Ground speed too fast.

Set to FAST throttle.Engine speed too slow.Engine stalls easily with mower engaged.

Slow down.Ground speed too fast.

Refer to the

Service Air Filter

section.Dirty or clogged air cleaner.

Cut tall grass at maximum Height-of-Cut during first

pass.

Height-of-Cut set too low.

Run engine for several minutes to warm up.Engine not up to operating temperature.

Start the mower in a cleared area.Starting mower in tall grass.

Engage PTO.PTO not engaged.Engines runs and rider drives, but mower will not cut.

Note:

For all other problems, contact an Authorized Service Dealer.

16

Specifications

Specification Chart

ModelItem

INTEK™ - Briggs & StrattonEngine

40.0 cu in. (656 cc)Displacement

9 ampElectrical System - Alternator, Regulated

12V - 195 CCABattery

48 oz (1,4 L)Oil Capacity

.030 in. (,76 mm)Spark Plug Gap

180 in.-lbs (20 Nm)Spark Plug Torque

2.9 gal (11 L)Fuel Tank Capacity

Transmission

Tuff Torq® Hydro K46BPMake and Type

Mower Deck

42 in. (107 cm)Cutting Width

2 or 3 Standard LiftNumber of Blades

1.5 to 4 in. (3,8 to 10,2 cm)Height of Cut

Chassis

15 x 6-6Front Wheels Size

12 to 14 psi (0,82 to 0,96 bar)Front Wheels Inflation Pressure

20 x 8-8Rear Wheels Size

10 psi (,68 bar)Rear Wheels Inflation Pressure

Power Ratings

The gross power rating for individual gasoline engine models is labeled in accordance with SAE (Society of Automotive Engineers)

code J1940 Small Engine Power & Torque Rating Procedure, and is rated in accordance with SAE J1995. Torque values are

derived at 2600 RPM for those engines with “rpm” called out on the label and 3060 RPM for all others; horsepower values are

derived at 3600 RPM. The gross power curves can be viewed at www.BRIGGSandSTRATTON.COM. Net power values are

taken with exhaust and air cleaner installed whereas gross power values are collected without these attachments. Actual gross

engine power will be higher than net engine power and is affected by, among other things, ambient operating conditions and

engine-to-engine variability. Given the wide array of products on which engines are placed, the gasoline engine may not develop

the rated gross power when used in a given piece of power equipment. This difference is due to a variety of factors including,

but not limited to, the variety of engine components (air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.), application

limitations, ambient operating conditions (temperature, humidity, altitude), and engine-to-engine variability. Due to manufacturing

and capacity limitations, Briggs & Stratton may substitute an engine of higher rated power for this engine.

Parts and Accessories

Contact an authorized dealer.

17

Indholdsfortegnelse:

Omfattede produkter i denne manual................................18

Generel information............................................................18

Kontaktoplysninger for europæisk kontor.......................18

Førersikkerhed ...................................................................18

Funktioner og betjeningsanordninger..............................20

Betjening..............................................................................21

Vedligeholdelse...................................................................26

Opbevaring..........................................................................29

Fejlfinding............................................................................30

Specifikationer.....................................................................31

Omfattede produkter i denne

manual

Følgende produkter er omfattede af denne manual:

2691487-00

Generel information

For yderligere information henviser vi til

Kundekontaktvejledning

og

Opsætningsvejledning

inkluderet med enheden.

Illustrationerne i dette dokument er repræsentative. Din maskine

kan variere fra de viste billeder.

VENSTRE

og

HØJRE

er

refereret fra betjeningspositionen.

Brugen af Bemærk i teksten indikerer afklaringer, undtagelser

eller alternativer til de givne procedurer.

Alle sprogoversættelser af dette dokument er udført med

udgangspunkt i den oprindelige engelske kildefil.

Al emballage, brugt olie og batterier skal bortskaffes med henblik

på genbrug i henhold til de gældende regeringsvedtægter.

Kontaktoplysninger for

europæisk kontor

Ved spørgsmål i forbindelse med europæiske emissioner bedes

du kontakte vores europæiske kontor på:

Max-Born-Straße 2, 68519 Viernheim, Germany.

Førersikkerhed

Opbevar denne vejledning til senere brug. Denne vejledning

indeholder sikkerhedsinformation, som gør dig opmærksom på

farer og risici forbundet med produktet, samt hvordan de kan

undgås. Den indeholder også vigtige instruktioner, der skal

følges ifm. den første indstilling, betjening og vedligeholdelse

af produktet.

Dette produkt er udelukkende konstrueret og beregnet til slåning

af velholdt græs. Det er ikke beregnet til noget andet formål.

Det er vigtigt, at du læser og forstår disse instruktioner, før du

forsøger at starte eller betjene dette udstyr.

Du skal være indgående bekendt med kontrolanordningerne

og den korrekte brug af udstyret.

Lær, hvordan du hurtigt stopper enheden og afbryder

kontrolanordningerne.

Guide til identifikation af skråninger

Sådan måler du hældningen på en græsplæne med en

smartphone eller et vinkelmålerværktøj:

ADVARSEL

Må ikke betjenes på skråninger, som er højere end 10grader.

1. Brug en lige kant mindst 0,6 meter (to fod) lang (A, figur 1).

Et 2x4 eller et lige stykke metal kan også du.

2. Vinkel -finder værktøj.

a. Brug din smartphone: Mange smartphones (B, figur

1) har en hældningsmåler sammen med kompas

-appen. Ellers kan du lede i en app store efter en

hældningsmåler-app.

b. Brug et hældningsmålerværktøj:

Hældningsmålerværktøj (C og D, figur 1) er tilgængelige

i lokale isenkræmmere eller online (også kaldet

inklinometer, vinkelmåler eller hældningsmåler).

Urskive-type (c) eller digital type (D) virker, andre gør

muligvis ikke. Følg instruktioner for hældnings

målerværktøjet.

3. Placér den 0,6 meter (to fod) lange, lige kant langs den

mest stejle del af plænehældningen. Placér brættet op og

ned langs hældningen.

4. Læg smartphonen eller hældningsmåleren langs kanten og

aflæs vinkelgraderne. Det er din græsplænes hældning.

Bemærk:

En identifikationsguide til papirmåler til hældninger er

inkluderet i produktmanualpakken og er også tilgængelig til at

downloade fra producentens hjemmeside.

Sikkerhedssymboler og deres betydninger

BetydningSymbolBetydningSymbol

Læs og forstå

brugervejledningen,

før brug af eller

servicering af

enheden.

Sikkerhedsinformation

om farer, som kan

resultere i

personskade.

18

BetydningSymbolBetydningSymbol

StopUdtag nøglen inden

udførelse af

vedligeholdelse. Læs

brugsanvisningen, før

service udføres.

EksplosionsfareBrandfare

Fare for giftige

dampe

Fare for stød

Brug

sikkerhedsbriller

Bevægelige Dele

Fare ved varm

overflade

Farligt kemikalie

Fare for slyngede

genstande

Fare for amputation af

lemmer

Hold børn vækHold

sikkerhedsafstand

Fare for amputation

af lemmer

Fare for rulning

Sikkerhedssymboler og signalord

Advarselssymbolet fare identifikanter sikkerhedsinformation

om farer, som kan resultere i personskade. Et signal ord (FARE,

ADVARSEL, eller BEMÆRK) bliver brugt sammen med

alarmsymbolet for at illustrere sandsynligheden og den mulige

grad af skade. Desuden kan et faresymbol bruges til at illustrere

faretypen.

FARE indikerer en fare, der, hvis ikke undgået, vil medføre

dødsfald eller alvorlige personskader.

ADVARSEL indikerer en fare, der, hvis ikke undgået, kunne

medføre dødsfald eller alvorlige personskader.

BEMÆRK indikerer en fare, der, hvis ikke undgået, kunne

medføre mindre eller moderat skade.

BEMÆRK

indikerer en situation, som kan medføre beskadigelse

af produktet.

Sikkerhedsmærkater

Før du betjener din maskine, skal du læse og forstå

sikkerhedsmærkaterne. Sammenhold figurerne 2 med den

efterfølgende tabel. Advarslerne og sikkerhedsforanstaltningerne

er for din egen sikkerheds skyld. For at undgå personskade

eller beskadigelse af maskinen, bedes du sørge for, at du forstår

og følger alle sikkerhedsmærkaterne.

Hvis nogen af sikkerhedsmærkaterne bliver slidte eller

beskadigede og ulæselige, skal du bestille nye hos din lokale

forhandler.

A

B

C

D

19

Sikkerhedsmærkatikoner

ADVARSEL: Læs, og gør dig bekendt med

betjeningsvejledningen, inden du bruger denne maskine. Vær

bekendt med placeringerne og funktionerne af alle

betjeningsanordninger. Du må ikke bruge denne maskine,

medmindre du har lært at bruge den.

1

FARE - TAB AF TRÆKKRAFT, SKRIDNING, STYRING OG

HERREDØMME PÅ SKRÅNINGER: Hvis maskinen ikke vil køre

fremad eller begynder at skride på en skråning, skal du standse

klipningen og langsomt køre væk fra skråningen.

2

FARE: BRANDFARE: Hold maskinen ren for græs, blade og

overskydende olie. Påfyld ikke brændstof, når motoren er varm

eller kører. Stop motoren, udtag nøglen, og lad den køle af i mindst

tre minutter, før du fylder brændstof på. Fyld ikke brændstof på

indendørs eller i en lukket anhænger eller garage eller andre

indelukkede områder. Tør spildt brændstof op. Ryg ikke under

betjening af denne maskine.

3

FARE - FOR AT VÆLTE OG SKRIDE: Slå græs op og ned og

ikke på tværs af skråninger. Må ikke betjenes på skråninger, som

er stejlere end 10 grader. Undgå pludselige og skarpe (hurtige)

sving på skråninger.

4

FARE - AMPUTATION OG ALVORLIG LEMLÆSTELSE: For at

undgå ulykker fra roterende skær og bevægelige dele skal du

sørge for, at sikkerhedsanordningerne (skærme og kontakter) er

på plads og er funktionsdygtige.

5

Undlad at slå græs, når der er børn eller andre personer i

nærheden. Tag aldrig passagerer med, specielt ikke børn, heller

ikke selvom skærene er slået fra. Slå ikke græs i bakgear,

medmindre det er ubetinget nødvendigt. Kig dig tilbage og nedad

før og mens du bakker.

6

Se den tekniske manual, inden du udfører reparationer eller

vedligeholdelse. Når du forlader maskinen, så sluk for motoren,

træk håndbremsen, og fjern tændingsnøglen.

7

Hold uvedkommende og børn på behørig afstand. Fjern

genstande, der kan risikere at blive slynget afsted af de roterende

skær. Undlad at slå græs hvis affaldsslisken ikke er på plads.

8

Undlad at slå græs, hvis affaldsslisken eller hele opsamleren ikke

er på plads.

9

For at undgå ulykker med roterende skær skal du holde dig på

afstand af klippeaggregatets kant og ligeledes holde andre væk.

10

Sikkerhedsmeddelelser

ADVARSEL

Du skal læse, forstå og følge alle instruktioner og advarsler i

producentens manual og på maskinen, motoren og tilkoblet

udstyr , før du betjener denne maskine. Manglende

overholdelse af sikkerhedsforanstaltningerne i denne manual

og på udstyret kunne resultere i død eller alvorlig personskade.

• Tillad kun kørere, der er ansvarlige, trænede og bekendte

med instruktionerne og fysisk i stand til at betjene

maskinen.

• Brug aldrig maskinen, hvis du er under indflydelse af

alkohol eller narkotika.

• Brug beskyttelsesbriller og lukket fodtøj.

• Hold ikke dine hænder eller fødder nær ved roterende

dele eller under maskinen. Hold til enhver tid afstand fra

udkaståbningen.

• Hold maskinen i god stand. Udskift slidte og beskadigede

dele.

• Vær forsigtig, når du betjener knivene. Indpak knivene

eller brug handsker. Erstat beskadigede knive. Reparér

eller ændr ikke knivene.

• Brug ramper i fuld bredde for at laste eller losse en

maskine til transport.

• Se vedhæftede eller tilbehør for passende hjulvægt eller

modvægte.

• For at forebygge brand skal du holde maskinen fri for

ophobning af græs, blade eller andet snavs ; tør spild af

olie eller brændstof op, fjern alt affald ramt af brændstof

og lad maskinen køle af før opbevaring.

ADVARSEL

Kørende motorer udsender kulilte, en lugtfri, farveløs, giftig

luftart. Indånding af kulilte kan forårsage hovedpine, træthed,

svimmelhed, opkast, forvirring, anfald, kvalme, besvimelse

eller dødsfald.

• Brug KUN udstyret udendørs.

• Sørg for at forhindre udstødning i at komme ind på et

lukket område gennem vinduer, døre, ventilationskanaler

eller andre åbninger.

Funktioner og

betjeningsanordninger

Match henvisningsbogstaver i Figur 3 til funktionerne og

styregrebene, der passer til din maskine og er opstillet i den

medfølgende oversigt.

20

La pagina si sta caricando...

Simplicity SPX110 Manuale utente

Questo manuale è adatto anche per

Simplicity SPX110 Manuale utente

in altre lingue

Documenti correlati

Altri documenti