Bluewater Pro 600CV-HR Manuale del proprietario

BLUEWATER PRO

WATER PURIFIER

OWNER’S MANUAL

ID

EN

FR

ES

PT

IT

DE

PL

RU

SE

FI

NO

DK

ZH

KO

Applies only to products with serial number 1845-01001 and later

02

Owner’s manual

CONTENTS

OWNER’S MANUAL - EN 03

MANUEL DU PROPRIÉTAIRE - FR 16

MANUAL DE USO - ES 29

MANUAL DO PROPRIETÁRIO - PT 42

MANUALE DEL PROPRIETARIO - IT 55

BEDIENUNGSANLEITUNG - DE 68

INSTRUKCJA OBSŁUGI - PL 81

РУКОВОДСТВО ВЛАДЕЛЬЦА - RU 94

HANDBOK - SE 107

OMISTAJAN KÄSIKIRJA - FI 120

BRUKERHÅNDBOK - NO 133

BETJENINGSVEJLEDNING - DK 146

用户手册 - ZH 159

PANDUAN PEMILIK - ID 172

사용자 설명서 - KO 185

About this manual

This manual gives you the necessary instructions to operate and do minor troubleshooting on the

device. For more information

Bluewater global website

www.bluewatergroup.com

Bluewater China website

Original language

The original language of this instruction is English, all other languages are translations of the original

instruction.

Regulatory information

Symbol Desicription

The CE marking and the related EC Declaration of Conformity is valid for the device when it is used in the same

condition as it was delivered from the manufacturer.

Limited warranty

Please visit www.bluewatergroup.com/warranty for more information on Limited warranty.

Symbols

The following symbols can be found on the water puriﬁer:

Symbol Desicription

The ETL Listed Mark is proof that the device has been independently tested and meets the applicable published

standard.

03

EN

CONTENTS

SAFETY 04

Safety instructions 04

Safety information 04

PRODUCT OVERVIEW 06

Models 06

Pro outside 06

Pro inside and replacement components 07

SYSTEM OVERVIEW 08

System description 08

Water production 09

Installation 10

Leak protection system 10

Low pressure protection 10

MAINTENANCE 11

Daily maintenance 11

Regular maintenance 11

TECHNICAL INFORMATION 12

TROUBLESHOOTING 14

How to solve simple problems 14

Customer service

See "Troubleshooting" to solve minor problems before calling service.

If you need external service support, it can cost money.

Make sure to have the following data (found on the data plate) available

when calling Bluewater:

– Model

– Product number

– Serial number

Environment information

80% of the the water puriﬁer components and its packaging have a label to help you

recycle and discard it correctly. The water puriﬁer is more ecient when it cleans

water for longer periods. Example: do not ﬁll a glass with water. Fill a jug instead.

Appliances bearing this symbol must be deposited at the designated local reception

point for the disposal of electrical and electronic equipment. This product may not be

disposed by using the normal household refuse collection processes.

OWNER’S MANUAL - EN

04

Owner’s manual

SAFETY

Safety instructions

Before you install or operate the device, you must read the safety information. Obey the

instructions in this manual to prevent injuries or damage to the equipment. This manual

contains CAUTIONS and NOTICES that are applicable for the safe operation of the device.

A CAUTION identiﬁes conditions that can cause injury, or

damage to the equipment.

Obey the instructions and do not continue until all conditions

are accepted and engaged.

A Note identiﬁes important information for a trouble free and optimal use of the water

puriﬁer.

Safety information

Only use the cleaned water when the lights “Puriﬁcation level II

and/or III” on the control panel are on.

This appliance can be used by children who are more than 8

years old. It can also be used by persons with reduced physical,

sensory or mental capabilities or lack of experience and

knowledge, if they have been given supervision or instruction

about the use of the appliance in a safe way and understand the

hazards involved.

Do not repair or modify parts of the water puriﬁer. This can

make it operate incorrectly, and lead to injury and damage not

covered by warranty.

Pro is a reverse osmosis system. It contains a replaceable

membrane that is very important for eective reduction of total

dissolved solids (TDS). Replace this membrane regularly.

Only approved Bluewater sta can do servicing and repairs on

the water puriﬁer. Only use original replacement cartridges and

parts from Bluewater. For the spare parts catalogue and contact

information for purchases, see www.bluewatergroup.com.

The water to be cleaned must obey the requirements in

"Technical information". Test the water when the water puriﬁer

has been installed, and then one time every year. If the water is

not clean, tastes, or smells bad, do not drink it.

05

EN

Installation must comply with applicable local plumbing codes

and regulations.

Connect the water puriﬁer to an earthed electrical supply. Use

a plug that is easy to access after installation. Only an approved

electrician must do permanent wiring on the system. A safety

switch must be installed on the system. Incorrect installation

can lead to damage, or make the water puriﬁer dangerous to

use.

Do not use the power cord if there are visible signs of damage

on it. If the power cord is damaged, a qualiﬁed electrician must

replace it in order to prevent danger.

Do not use Pro without a ﬁlter. To do so can cause damage.

When Pro is cleaned or put in storage, the ﬁlter can be

removed.

If the water puriﬁer is disconnected from water and electricity for >5 days, store it as

described in Complete User manual “Storage”.

06

Owner’s manual

PRODUCT OVERVIEW

Models

Model Capable of handling

higher TDS, including

brackish inlet water

Suitable for commercial

use without an automatic

shuto

Clean water rinse valve

suitable for environments

where extra high water

quality is required

Pro 400B-HR



Pro 400C-HF



Pro 400C-HR



Pro 400BC-HR

 

Pro 400CV-HR

 

Pro 400BCV-HR

  

Pro 600C-HF



Pro 600CV-HR

 

Pro outside

1

2 3 4 5 87 9

10 11 12

6

Figure 1. Pro outside

Pos Description Pos Description

1 Control panel 7 Electrical connection for faucet (optional)

2 Front cover 8 Drain water hose

3 Clean water connection 9 Power cord

4 Clean water tube 10 Feed water tube

5 Rinse water tube (only for CV models) 11 Grid ﬁlter

6 Air-gap bracket (only for CV models) 12 Feed water connection

07

EN

Control panel

For information about combinations of lights that ﬂash/are on, see

"Troubleshooting".

1

2

3

4

5

6 7 8

Figure 2. Control panel

Pos Light/button Description

1 on/o On:

O:

Flashes:

The water puriﬁer is connected to power.

The water puriﬁer is not connected to power.

The water puriﬁer ﬂushes. Flushing cannot be stopped.

2 ﬁlter I On: The ﬁlter must be replaced. Pro 600: Replace both

Carbon Block ﬁlters.

3 ﬁlter II On: The ﬁlter must be replaced. Pro 600: Replace both

Carbon Block ﬁlters.

4 stop Flashes/On: Something is wrong, see "Troubleshooting".

5 calibration Calibration button, various functions see Complete

User manual.

6 puriﬁcation level I On: Puriﬁcation level I-III indicates clean water puriﬁcation

level. Low level I to high level III.

7 puriﬁcation level II

8 puriﬁcation level III

Pro inside and replacement components

Figure 3. Pro inside

1

2 3 4

Pos Description Art.-Nr.

1 Base plate

2 Preﬁlter I, Pro 600: Carbon Block 919240005

Preﬁlter I, Pro 400: Sediment ﬁlter 919240002

3 Preﬁlter II, Pro 600: Carbon Block 919240005

Preﬁlter II, Pro 400: Carbon ﬁlter,

granulated

919240003

4 Reverse osmosis membrane

Membrane service kit, type HR

(High Rejection)

150718900-SP

Membrane service kit, type HF

(High Flow)

150718901-SP

08

Owner’s manual

SYSTEM OVERVIEW

System description

1

2

3

4

5

6

Figure 4. System overview, an example of Pro installation

Pos Description Pos Description

1 Water puriﬁer 4 Drain water hose, installed with an air-gap

2 Power cord 5 Bracket for drain water hose

3 Feed water tube 6 Clean water tube

09

EN

Water production

Only use the cleaned water when the lights “Puriﬁcation level II

and III” on the control panel are on. It can take up to 60 seconds

before the water puriﬁer indicates good water quality.

For models suitable for commercial use the faucet could be replaced by for example a

valve or a tank.

Figure 5. Water production on/o

Automatic ﬂush

The length of the ﬂush process varies between 5-120 seconds, depending on how

long the previous drawing of water lasted.

An automatic ﬂush will be performed if one of the conditions below are fulﬁlled:

12 h

15 min

2 min

1 2 3

Figure 6. Automatic ﬂush

Pos Description

1 Flush after drawing water. Every time after drawing water.

2 Flush when drawing water. After maximum operation time 15 minutes. (Pro 400B must be

manually restarted)

3 Water puriﬁer in standby mode. Pro is connected to water and power. Flush is performed

every 12 hours, regardless of when clean water was last produced.

10

Owner’s manual

Installation

Pro must not supply water to all the faucets in the house. This

can cause corrosion in the water pipes and water heaters. If Pro

is not correctly installed, warranty will not cover it.

Installation must comply with applicable local plumbing codes

and regulations.

Only connect the water puriﬁer to the cold water supply. The

water must be of sucient quality and fulﬁll the requirements

on feed water.

The ﬁrst time Pro is connected to water and power, it does an

automatic cleaning procedure. The cleaning time is 55 minutes.

Cleaning cannot be stopped. Keep Pro connected to power,

and leave the faucet open.

We recommend that the water puriﬁer is installed by a professional, who is

recommended by an authorized Bluewater dealer. Installation instructions can be

found in the Complete User manual and on www.bluewatergroup.com.

Leak protection system

A sensor at the bottom of the water puriﬁer senses water leaks. If there is a leak, the feed

water supply is stopped. The water puriﬁer cannot be started again until the leak has been

repaired.

Low pressure protection

If Pro stops because of low feed water pressure, the cause

of the low pressure must be removed. If not, Pro can be

permanently damaged.

When Pro has stopped because of a low pressure problem (feed

water), water production can be started manually by pushing

the calibration button.

Low pressure restart function

Only included in models suitable for commercial use.

The low pressure restart is a function to ensure maximum availability of water.

Pro starts automatically when it has stopped because of low pressure. It tries to start three

times: after 3 minutes, after 20 minutes and after 4 hours. If the water pressure is not

suciently high after three tries, Pro will stop.

11

EN

MAINTENANCE

Daily maintenance

Check indicator lights

Step Action

1 Make sure that the lights on the control panel are not on or ﬂashes.

Clean the water puriﬁer

Do not use chemicals to clean the surface. Alcohol, petrol,

organic and inorganic acids, strong basic chemicals (such as

concentrated dish washing detergent) will cause damage to the

surface.

Do not use hard or sharp tools to clean the water puriﬁer.

Step Action

1 Clean the outer surface with a soft moist cloth and a weak soap solution to remove dust,

stains and dirt.

2 Dry with a soft dry cloth.

Regular maintenance

Regular maintenance is important for correct function and long

term operation. Only educated and approved personnel can do

the maintenance.

For instructions on how to do maintenance, see Complete User manual

on www.bluewatergroup.com.

Frequency Action

1 month Check connections.

Wipe o condensation from base plate.

4-6 months* Replace ﬁlters. Replace the ﬁlters after what comes ﬁrst of 4-6 months or

37 850 l (10 000 gal) of puriﬁed water.

6 months* Descale.

1 year Test the water every year. If the water is not clean, do not drink it. Contact a

Bluewater dealer.

4-6 years* Replace reverse osmosis membrane. Contact your Bluewater dealer.

*Frequency depending on inlet water quality and usage

12

Owner’s manual

TECHNICAL INFORMATION

Model Size W×H×D Weight Power Power supply earthed

Pro 400B-HR 230V 225×466×460 mm 29 kg 530 W 230V, 50-60 Hz

120V 8.9×18.3×18.1 “ 64 lbs 6 Amp 120V, 60 Hz

Pro 400C-HF 230V 225×466×460 mm 29 kg 530 W 230V, 50-60 Hz

120V 8.9×18.3×18.1 “ 64 lbs 6 Amp 120V, 60 Hz

Pro 400C-HR 230V 225×466×460 mm 29 kg 530 W 230V, 50-60 Hz

120V 8.9×18.3×18.1 “ 64 lbs 6 Amp 120V, 60 Hz

Pro 400BC-HR 230V 225×466×460 mm 29 kg 530 W 230V, 50-60 Hz

120V 8.9×18.3×18.1 “ 64 lbs 6 Amp 120V, 60 Hz

Pro 400CV-HR 230V 225×466×470 mm 29 kg 530 W 230V, 50-60 Hz

120V 8.9×18.3×18.5 “ 64 lbs 6 Amp 120V, 60 Hz

Pro 400BCV-HR 230V 225×466×470 mm 29 kg 530 W 230V, 50-60 Hz

120V 8.9×18.3×18.5 “ 64 lbs 6 Amp 120V, 60 Hz

Pro 600C-HF 230V 225×466×460 mm 29 kg 720 W 230V 50-60 Hz

Pro 600CV-HR 230V 225×466×470 mm 29 kg 720 W 230V 50-60 Hz

Requirements on feed water to water puriﬁer

Model

Temperature

Feed water

ﬂowing

pressure

Water ﬂow

TDS

(Total Disolved

Solids) [ppm]

Conductivity

[µS/cm, 25 °C

(77 °F)]

Hardness

Iron Fe

(+2)

/Fe

(+3)

[mg/l]

Turbidity

[FNU]

Pro

400B-HR

Pro

400BC-

HR

Pro

400BCV-

HR

230V 2-30 °C 2-10

bar

0.2-1

MPa

> 10

l/min

< 7500 < 13 000 < 20 °dH < 1.5/

< 0.3

< 0.5

120V 36-86 °F 29-145

psi

> 2.6

gal/min

< 20.9

grains/gal

Pro

400C-HF

Pro

400C-HR

Pro

400CV-

HR

230V 2-35 °C 2-10

bar

0.2-1

MPa

> 10

l/min

< 1500 < 2000 < 20 °dH < 1.5/

< 0.3

< 0.5

120V 36-95 °F 29-145

psi

> 2.6

gal/min

< 20.9

grains/gal

Pro

600C-HF

Pro

600CV-

HR

230V 2-35 °C 2.5-10

bar

0.25-1

MPa

> 10

l/min

< 1500 < 2000 < 20 °dH < 1.0/

< 0.3

< 0.5

13

EN

Do not use with water that is microbiologically unsafe or of

unknown quality without sucient disinfection before or after

the system.

Only connect to the cold water supply. The temperature limits

are in the table "Requirements on feed water to water puriﬁer".

For more detailed information see www.bluewatergroup.com.

14

Owner’s manual

TROUBLESHOOTING

How to solve simple problems

If Pro stops because of an emergency, disconnect it from power and connect it again,

or press calibration button to reset the emergency stop.

For more severe problems, see Complete User manual on www.bluewatergroup.com.

Symptom Cause Solution

The on/o light ﬂashes. The water puriﬁer ﬂushes. Flushing

cannot be stopped.

Filter I must be replaced.

Pro 600: Replace both ﬁlters.

See Complete User manual.

The grid ﬁlter is blocked. See Complete User manual.

The feed water pressure is too

low.

Make sure that the feed water pressure

is sucient. If necessary, increase the

pressure.

Filter II must be replaced.

Pro 600: Replace both ﬁlters.

See Complete User manual.

Pro 400 B-HR Filter II must be

replaced.

See Complete User manual.

Reset ﬁlter II.

The feed water pressure is too

low. The water puriﬁer has

stopped. It waits and must be

started again.

The water puriﬁer will try to start

automatically. Make sure that the feed

water pressure is sucient. If necessary,

replace the ﬁlters. See Complete User

manual.

Push the calibration button to start the

water puriﬁer. Release the button when

the ﬁlter I light and the stop light go out.

Filter I or ﬁlter II is blocked. Make sure that nothing in the ﬁlter makes

the water not ﬂow. If necessary, replace

ﬁlters. See Complete User manual.

The grid is blocked. See Complete User manual.

The feed water pressure is too

low.

Install a pump with increased pressure

for the feed water.

Do a check of the parts that have an

eect on the feed water pressure (the

water line, the coarse ﬁlter, the extra

pre-ﬁlter).

The water puriﬁer has

stopped. The clean water

quality has become too low.

Disconnect the water puriﬁer from

power. Connect it again to start the

automatic ﬂush. Do this 2 times.

The water quality meter does

not work correctly.

Disconnect the water puriﬁer from

power. Connect it again to start the

automatic ﬂush. Do not use the water

puriﬁer for 30 minutes.

15

EN

Symptom Cause Solution

The tap has been on for more

than 15 minutes. The water

puriﬁer has stopped. (Pro

400B)

Turn o the tap and wait at least

30 minutes.

Push the calibration button to start the

water puriﬁer. Release the button when

the stop light goes out.

The leak protection system is

activated.

Disconnect the water puriﬁer from

power, and clean the base plate.

The ﬁrst time cleaning

procedure is ongoing.

The water puriﬁer is working correctly.

The ﬁrst time cleaning

procedure has been

interrupted.

Make sure that the feed water pressure is

sucient. Push the calibration button to

start the water puriﬁer.

The ﬁrst time cleaning

procedure has been

interrupted.

Open the faucet on the clean water

tube (and on the rinse water tube for CV

models).

The ﬂow rate from the

clean water faucet is

low.

The clean water tube is

tensioned or jammed.

Make sure that the clean water tube can

move freely.

The water puriﬁer needs to be

descaled.

See Complete User manual.

The water puriﬁer starts

and stops again (short

starts).

The water pressure between

the water puriﬁer and the

faucet/valve/tank is below the

starting pressure level.

Examine the connections.

Make sure that the ends of the water

tubes are circular and have no burrs.

Make sure that the faucets and the valves

are water tight when they are closed.

There is a bad smell

from the water puriﬁer.

Microbial growth in the water

because the water puriﬁer has

not been used for a week or

longer.

See Complete User manual.

16

Manuel du propriétaire

TABLE DES MATIÈRES

SÉCURITÉ 17

Consignes de sécurité 17

Instructions de sécurité 17

PRÉSENTATION GÉNÉRALE DE L’ÉQUIPEMENT 19

Modèles 19

Extérieur de l’osmoseur Pro 19

Intérieur du dispositif Pro et composants de remplacement 20

PRÉSENTATION GÉNÉRALE DU SYSTÈME 21

Description 21

Production d’eau 22

Installation 23

Système anti-fuites 23

Système anti-basse pression 23

ENTRETIEN 24

Entretien quotidien 24

Entretien régulier 24

CARACTÉRISTIQUES TECHNIQUES 25

DÉPANNAGE 27

Résolution de problèmes simples 27

Service d’assistance technique

Consulter la section «DÉPANNAGE» pour tenter de

résoudre un problème avant de contacter le service

d’assistance. Si l’aide de techniciens externes est

nécessaire, celle-ci peut être payante.

Lors de tout contact avec Bluewater, se munir des

informations suivantes (celles-ci ﬁgurent sur la plaque

signalétique) :

– Modèle

– la référence produit

– le numéro de série

Données environnementales

80 % des composants de cet osmoseur, de même que son emballage, sont dotés

d’une étiquette précisant leur mode de recyclage ou de mise au rebut. L’ecacité

du dispositif est optimale lorsqu’il fonctionne sur de longues durées. Exemple : ne

remplissez pas un verre d’eau. Remplissez plutôt un pichet.

Les appareils portant ce symbole doivent être déposés au point de réception

local pour la mise au rebut des équipements électriques et électroniques usagés.

Ceproduit ne doit pas être éliminé avec les déchets ménagers ordinaires.

MANUEL DU PROPRIÉTAIRE - FR

17

FR

SÉCURITÉ

Consignes de sécurité

Avant d’installer et d’utiliser le dispositif, prendre connaissance des consignes de sécurité.

Ces consignes doivent être scrupuleusement suivies aﬁn de prévenir des blessures

physiques ou la détérioration de l’équipement. Ce manuel inclut des MISES EN GARDE

etdes REMARQUES destinées à garantir l’utilisation sécurisée du dispositif.

Une MISE EN GARDE signale une situation susceptible

d’entraîner des blessures physiques ou une dégradation

matérielle. Suivre les instructions et cesser toute utilisation de

l’équipement tant que la situation n’est pas redevenue normale.

Une REMARQUE fait état d’informations importantes pour une utilisation optimale et

en toute tranquillité de l’osmoseur.

Instructions de sécurité

Utiliser uniquement de l’eau nettoyée lorsque les voyants

«Puriﬁcation de niveau II et/ou III» s’achent sur le panneau

de commande.

Cet appareil peut être utilisé par les enfants de plus de 8ans.

Il peut également être manipulé par des personnes aux

capacités physiques, sensorielles ou mentales réduites ou par

des personnes manquant d’expérience ou de connaissances,

dans la mesure où elles sont sous surveillance, ont reçu

les instructions d’utilisation de l’appareil adéquates et

comprennent les risques associés.

Ne pas réparer ou modiﬁer les composants de l’osmoseur.

Il pourrait en résulter un dysfonctionnement du dispositif

susceptible de provoquer des blessures ou des détériorations

non couvertes par la garantie.

Pro est un système d’osmose inverse. Il contient une membrane

remplaçable très impor-tante pour réduire ecacement les

matières dissoutes totales. Remplacezla régulièrement.

Seuls les techniciens Bluewater agréés sont habilités à

entretenir et réparer cet osmoseur d’eau. Il est indispensable

d’utiliser les cartouches et composants de rechange originaux

de Bluewater. Pour consulter le catalogue des pièces détachées

et les coordonnées pour les achats, rendez-vous sur le site

www.bluewatergroup.com.

18

Manuel du propriétaire

L’eau à épurer doit répondre aux critères stipulés dans la

section «CARACTÉRISTIQUES TECHNIQUES». Testez l’eau après

que l’osmoseur a été installé, puis eectuez des tests une

fois par an. Si celle-ci n’est pas propre, a mauvais goût ou est

malodorante, ne pas la boire.

L’installation doit être conforme aux normes et réglementations de

plomberie locales applicables.

Brancher l’osmoseur sur une alimentation électrique mise à la

terre. La prise doit être aisément accessible après l’installation.

Seul un électricien agréé doit être autorisé à eectuer les

raccordements permanents. Le système doit comporter un

interrupteur de sécurité. Une installation incorrecte peut entraîner

des dommages ou mettre en danger l’utilisateur de l’osmoseur.

Ne pas utiliser le câble d’alimentation s’il présente des

signes visibles de dommages. En cas de dommage, le câble

d’alimentation doit être remplacé par un électricien qualiﬁé aﬁn

de prévenir tout danger.

Ne pas utiliser l’osmoseur Pro sans ﬁltre. Cela pourrait

l’endommager. Si l’osmoseur Pro est nettoyéou rangé, le ﬁltre

peut être ôté.

Si l’osmoseur est débranché de l’alimentation en eau et en électricité pendant plus de

5 jours, stockez-le conformément aux instructions de stockage du manuel «Complete

User manual».

19

FR

PRÉSENTATION GÉNÉRALE DE

L’ÉQUIPEMENT

Modèles

Modèle Capable de traiter un TDS

(matières dissoutes totales)

plus élevé, y comprisl’eau

d’arrivée saumâtre

Convient pour

une utilisation

commerciale sans

arrêt automatique

Le robinet pour l’eau puriﬁée

convient aux environnements

où une qualité d’eau

particulièrement élevée

estexigée

Pro 400B-HR



Pro 400C-HF



Pro 400C-HR



Pro 400BC-HR

 

Pro 400CV-HR

 

Pro 400BCV-HR

  

Pro 600C-HF



Pro 600CV-HR

 

Extérieur de l’osmoseur Pro

1

2 3 4 5 87 9

10 11 12

6

Figure 7. Extérieur de l’osmoseur Pro

N° Description N° Description

1 Panneau de commande 7 Raccord électrique pour robinet (en option)

2 Capot avant 8 Flexible pour eaux usées

3 Raccordement pour eau propre 9 Câble d'alimentation

4 Tuyau pour eau propre 10 Tuyau pour eau d'alimentation

5 Tuyau pour eau de rinçage (Modèles en CV) 11 Filtre à grille

6 Support du dispositif anti-retour (Modèles

en CV)

12 Raccordement pour eau d'alimentation

20

Manuel du propriétaire

Panneau de commande

Pour obtenir des informations concernant des combinaisons de voyants qui clignotent/

apparaissent, se reporter à la section «DÉPANNAGE».

1

2

3

4

5

6 7 8

Figure 8. Panneau de commande

N° Voyant/bouton Description

1 on/o On (sous tension):

O (hors tension):

Clignote:

L’osmoseur est branché sur le secteur.

L’osmoseur n’est pas branché sur le secteur.

L'osmoseur rince. Le rinçage ne peut être arrêté.

2 ﬁlter I On (sous tension): Le ﬁltre doit être remplacé. Pro 600: remplacer

les deux ﬁltres Carbon Block.

3 ﬁlter II On (sous tension): Le ﬁltre doit être remplacé. Pro 600: remplacer

les deux ﬁltres Carbon Block.

4 stop Clignote/Sous tension: Détection d’un problème, se reporter à la

section

«DÉPANNAGE».

5 calibration Bouton d’étalonnage, diérentes fonctions se

reporter au manuel «Complete User manual».

6 puriﬁcation level I On (sous tension): Le niveau de puriﬁcation I-III indique le niveau

de puriﬁcation de l’eau puriﬁée.

Niveau bas I à niveau élevé III.

7 puriﬁcation level II

8 puriﬁcation level III

Intérieur du dispositif Pro et composants de remplacement

Figure 9. Intérieur de l’osmoseur Pro

N° Description Référence

1 Plateau de base

2 Préﬁltre I, Pro 600 : Carbon Block 919240005

Préﬁltre I, Pro 400 : ﬁltre à

sédiments

919240002

3 Préﬁltre II, Pro 600 : Carbon Block 919240005

Préﬁltre II, Pro 400 : ﬁltre à

charbon, granulé

919240003

4

Membrane d'osmose inverse

Kit d'entretien de membrane, type

HR (High Rejection, rejets élevés)

150718900-SP

Kit d'entretien de membrane, type

HF (High Flow, haut débit)

150718901-SP

1

2 3 4

La pagina sta caricando ...

Bluewater Pro 600CV-HR Manuale del proprietario

Questo manuale è adatto anche per

Bluewater Pro 600CV-HR Manuale del proprietario

in altre lingue

Altri documenti